project/netifd.git
3 years agointerface-ip: add unreachable route if address is offlink openwrt-19.07
Hans Dedecker [Sat, 9 Jan 2021 20:18:45 +0000 (21:18 +0100)]
interface-ip: add unreachable route if address is offlink

In order to avoid a routing loop add an unreachable route for the
address prefix is the offlink flag is set for an address.
This fixes a routing loop which is currently present on point-to-point
links (e.g PPP) when the wan interface is assigned a globally unique
prefix (e.g. 2001:db8:1:0::/64) from which an IPv6 address is picked
and installed on the wan interface
(e.g. 2001:db8:1:0:5054:ff:feab:d87c/64)

The prefix route 2001:db8:1::/64 would be present in the routing table
which will route any packet with as destination 2001:db8:1::/64 to the wan
interface and would be routed back by the upstream router due to the
wan interface due to the assigned global unique prefix.
Besides not installing the prefix route 2001:db8:1::/64 on point-to-point links
adding an unreachable route is required to avoid the routing loop.

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
(cherry picked from commit c00c8335d6188daa326ecfe5a62da15a9b9987e1)

5 years agosystem-linux: fix resource leak
Hans Dedecker [Mon, 5 Aug 2019 20:05:36 +0000 (22:05 +0200)]
system-linux: fix resource leak

Fix cb leak in case invalid type is specified in system_if_clear_entries
Detected by Coverity in CID1431183

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
5 years agosystem-linux: Coverity fixes
Hans Dedecker [Sun, 21 Jul 2019 21:10:34 +0000 (23:10 +0200)]
system-linux: Coverity fixes

Fixes CID 122043014322261432807 and 1433508

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
5 years agonetifd: fix xfrm interface deletion and standardize netlink call
André Valentin [Fri, 14 Jun 2019 11:09:45 +0000 (13:09 +0200)]
netifd: fix xfrm interface deletion and standardize netlink call

-xfrm interfaces were deleted before
-use standard parameters for xfrm interface created

Signed-off-by: André Valentin <avalentin@marcant.net>
5 years agointerface-ip: fix possible null pointer dereference
Hans Dedecker [Thu, 13 Jun 2019 19:59:31 +0000 (21:59 +0200)]
interface-ip: fix possible null pointer dereference

Reported by Coverity in CID 1445749

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
5 years agosystem-linux: remove superfluous dev check
Hans Dedecker [Thu, 13 Jun 2019 19:48:00 +0000 (21:48 +0200)]
system-linux: remove superfluous dev check

No need to check if dev is NULL as device is always set when
system_neigh is called

Fixes issue reported by Coverity in CID 1445818

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
5 years agonetifd: add xfrm tunnel interface support
André Valentin [Sat, 8 Jun 2019 11:48:09 +0000 (13:48 +0200)]
netifd: add xfrm tunnel interface support

This adds support for xfrm interfaces. These interfaces can be used since
linux 4.19 for IPsec traffic, like VTI interface.
XFRM interfaces are less complicated compared to VTI because they need no IP
tunnel endpoints.

5 years agoiprule: fix missing ip rules after a reload (FS#2296)
Hans Dedecker [Mon, 27 May 2019 19:01:25 +0000 (21:01 +0200)]
iprule: fix missing ip rules after a reload (FS#2296)

Since commit 5cf79759a24e9bb2a6a3aef7c83d73efb9bf2df3 (iprule: rework
interface based rules to handle dynamic interfaces) the rule
comparison is broken and doesn't correctly recognize matching rules.
This in turn break the reloading as adding the "new" rule fails
because it already exists and it then delete the "old" rule.

The comparison is broken because it now include fields that are not
defining the rule itself, as well as some pointer to malloced strings.
To fix this we move back the offending fields in the iprule struct
before the 'flags' field and match the malloced strings separately.

Signed-off-by: Alban Bedel <albeu@free.fr>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
5 years agointerface-ip: use ptp address as well to find local address target
Hans Dedecker [Fri, 17 May 2019 16:27:59 +0000 (18:27 +0200)]
interface-ip: use ptp address as well to find local address target

In case of tunnel over PPP(such as gretap over l2tp): tunnel interface
use PPP's peer address as remote address, netifd script will call
proto_add_host_dependency function, then netifd will search which device
can reach to the remote address. Before the patch, netifd don't consider
the PPP interface can reach to the remote address, so netifd will select
default route to remote address, it will lead to remote address unreachable.

Based on a patch by xiaofan <xfan1024@live.com>

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
5 years agotreewide: pass bool as second argument of blobmsg_check_attr
Hans Dedecker [Thu, 16 May 2019 20:09:36 +0000 (22:09 +0200)]
treewide: pass bool as second argument of blobmsg_check_attr

blobmsg_check_attr() takes as second argument a bool; fix it where needed

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
5 years agointerface-ip: fine tune IPv6 mtu warning
Hans Dedecker [Wed, 8 May 2019 19:33:05 +0000 (21:33 +0200)]
interface-ip: fine tune IPv6 mtu warning

Failing to set the IPv6 mtu is only a real issue if the mtu to be set is
smaller than the current mtu as in that case it would break IPv6 path mtu;
adapt the logic to generate the warning accordingly

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
5 years agointerface: tidy ipv6 mtu warning
Kevin Darbyshire-Bryant [Tue, 7 May 2019 19:37:25 +0000 (20:37 +0100)]
interface: tidy ipv6 mtu warning

Add missing space to change from:

netifd: Failed to set IPv6 mtu to 1500on interface 'wg0'

to:

netifd: Failed to set IPv6 mtu to 1500 on interface 'wg0'

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
5 years agosystem-linux: remove debug tracing
Hans Dedecker [Mon, 15 Apr 2019 21:13:51 +0000 (23:13 +0200)]
system-linux: remove debug tracing

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
5 years agointerface: add neighbor config support
meurisa [Fri, 12 Apr 2019 07:56:28 +0000 (09:56 +0200)]
interface: add neighbor config support

The neighbor or neighbor6 network section makes neighbours
configurable via UCI or proto shell handlers. It allows to
install neighbor proxy entries or static neighbor entries

The neighbor or neighbor6 section has the following types:
interface : declares the logical OpenWrt interface
ipaddr : the ip address of the neighbor
mac : the mac address of the neighbor
proxy : specifies whether the neighbor ia a proxy
entry (can be 1 or 0)
router : specifies whether the neighbor is a router
 (can be 1 or 0)

Signed-off-by: Alexander Meuris <meurisalexander@gmail.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
5 years agointerface: fix "if-down" hotplug event handling
Martin Schiller [Fri, 12 Apr 2019 07:19:14 +0000 (09:19 +0200)]
interface: fix "if-down" hotplug event handling

commit a97297d83e42 ("interface: set interface in TEARDOWN state when checking link state")
broke the if-down hotplug event handling, as the iface->state is now IFS_TEARDOWN when
calling the mark_interface_down() function from the IFPEV_DOWN event.

Fixes: a97297d83e42 ("interface: set interface in TEARDOWN state when checking link state")
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
5 years agoproto-shell: return error in case setup fails
Hans Dedecker [Mon, 1 Apr 2019 11:53:50 +0000 (13:53 +0200)]
proto-shell: return error in case setup fails

In case PROTO_CMD_SETUP cannot be handled due to an invalid state; return
-1 so the calling functions are aware the PROTO_CMD_SETUP has failed.

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
5 years agointerface: set interface in TEARDOWN state when checking link state
Hans dedecker [Mon, 1 Apr 2019 08:34:26 +0000 (10:34 +0200)]
interface: set interface in TEARDOWN state when checking link state

When launching PROTO_CMD_TEARDOWN in interface_check_state() the interface
was set in IFS_DOWN state. In case an interface is now brought into IFS_SETUP
state in __interface_set_up() it will launch PROTO_CMD_SETUP trying to
bring the proto shell handler in S_SETUP state which will fail as the proto
shell handler is still in the S_TEARDOWN state.

Fix this by setting the interface in IFS_TEARDOWN state when the PROTO_CMD_TEARDOWN
event is launched which will prevent the interface being brought into IFS_SETUP state
as long as it's not in the IFS_DOWN state.

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
5 years agonetifd: wireless: Add support for 802.11ad
Robert Marko [Wed, 13 Mar 2019 13:34:57 +0000 (14:34 +0100)]
netifd: wireless: Add support for 802.11ad

This simple patch adds 802.11ad to hwmode list so that netifd-wireless.sh does not otherwise overwrite it with the default hwmode=g

Signed-off-by: Robert Marko <robimarko@gmail.com>
5 years agonetifd: wireless: Add support for GCMP cipher
Robert Marko [Thu, 14 Mar 2019 10:03:16 +0000 (11:03 +0100)]
netifd: wireless: Add support for GCMP cipher

This patch will add support for using GCMP as cipher suite.
This is not a strong cipher but is only one supported by
wil6210 driver in order to have encrypted traffic.

Signed-off-by: Robert Marko <robimarko@gmail.com>
5 years agointerface-ip: fix delegate config update on reload (FS#2087)
Hans Dedecker [Wed, 13 Mar 2019 13:56:21 +0000 (14:56 +0100)]
interface-ip: fix delegate config update on reload (FS#2087)

Update the no_delegation parameter on a config reload; in case prefixes
are present update the prefix assignments as well according to the
no_delegation status

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
5 years agosystem-linux: handle hotplug event socket ENOBUFS errors
Alin Nastac [Thu, 31 Jan 2019 10:20:29 +0000 (11:20 +0100)]
system-linux: handle hotplug event socket ENOBUFS errors

Hotplug events are no longer handled after socket RX queue is
overrun. The issue has been fixed by:
  - setting SO_RCVBUF initially to 65535
  - doubling SO_RCVBUF value each time RX queue gets overrun

Signed-off-by: Alin Nastac <alin.nastac@gmail.com>
5 years agoproto: fix logic inversion in previous commit
Kevin Darbyshire-Bryant [Mon, 17 Dec 2018 18:26:11 +0000 (18:26 +0000)]
proto: fix logic inversion in previous commit

Rogue ! effectively disabled the ipv6 multicast check.  Fix cd089c52

Why is it always the simple changes that catch you out?

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
5 years agoproto: Support class-e addressing in netifd
Dave Taht [Sun, 9 Dec 2018 04:52:33 +0000 (04:52 +0000)]
proto: Support class-e addressing in netifd

Signed-off-by: Dave Taht <dave.taht@gmail.com>
Acked-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Acked-by: Jo-Philipp Wich <jo@mein.io>
5 years agosystem-linux: get rid of SIOCSDEVPRIVATE
Hans Dedecker [Thu, 13 Dec 2018 15:13:06 +0000 (16:13 +0100)]
system-linux: get rid of SIOCSDEVPRIVATE

Use sysfs to configure the bridge settings stp/forward_delay/priority
ageing_time/hello_time and max_age as the SIOCDEVPRIVATE bridge ioctl
has no compat ioctl support which makes it impossible to set the above
mentioned bridge paramaters if the kernel is compiled in 64 bit mode
and user_space in 32 bit mode.

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
5 years agointerface: fix return code of __interface_add()
Hans Dedecker [Mon, 26 Nov 2018 12:55:53 +0000 (13:55 +0100)]
interface: fix return code of __interface_add()

For dynamic interfaces don't return false if vlist_find returns NULL as
the calling function will try to free iface in case of an error which has
already been freed in interface_change_config()

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
5 years agonetifd: fix resource leak on error in netifd_add_dynamic()
Hans Dedecker [Mon, 26 Nov 2018 08:59:52 +0000 (09:59 +0100)]
netifd: fix resource leak on error in netifd_add_dynamic()

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
5 years agoconfig: fix resource leaks on error in config_parse_interface()
Hans Dedecker [Mon, 26 Nov 2018 08:45:47 +0000 (09:45 +0100)]
config: fix resource leaks on error in config_parse_interface()

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
5 years agointerface: fix memory leak on error in __interface_add()
Hans Dedecker [Mon, 26 Nov 2018 08:24:02 +0000 (09:24 +0100)]
interface: fix memory leak on error in __interface_add()

Detected by Coverity in cid 1441495

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
6 years agotreewide: switch to C-code style comments
Hans Dedecker [Mon, 19 Nov 2018 08:59:05 +0000 (09:59 +0100)]
treewide: switch to C-code style comments

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
6 years agotreewide: make some functions static
Hans Dedecker [Sat, 17 Nov 2018 17:41:16 +0000 (18:41 +0100)]
treewide: make some functions static

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
6 years agointerface: fix removal of dynamic interfaces
Hans Dedecker [Fri, 16 Nov 2018 15:25:41 +0000 (16:25 +0100)]
interface: fix removal of dynamic interfaces

Set config state to remove for dynamic interfaces in the following cases :
-interface is set as not available
-interface is set as down
-interface is set as having no link state
This will trigger an interface delete upon the next call of interface_handle_config_change

Before this change you could end up with lingering inactive dynamic
interfaces in case the aliased interface went down as before a dynamic
interface was only removed when set down via ubus

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
6 years agointerface: rework code to get rid of interface_set_dynamic
Hans Dedecker [Sun, 11 Nov 2018 20:15:56 +0000 (21:15 +0100)]
interface: rework code to get rid of interface_set_dynamic

Integrate dynamic interface creation code into interface_alloc and
__interface_add so we can get rid of interface_set_dynamic

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
6 years agosystem-linux: enable by default ignore encaplimit for grev6 tunnels
Hans Dedecker [Wed, 17 Oct 2018 07:35:11 +0000 (09:35 +0200)]
system-linux: enable by default ignore encaplimit for grev6 tunnels

Similar as for ip6 tunnels ignore encaplimit by default as not all ISPs
support the destination option header containing the tunnel encapsulation
limit resulting into broken connectivity

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
6 years agosystem-linux: fix a typo in gre tunnel data parsing logic
Hans Dedecker [Tue, 16 Oct 2018 14:16:49 +0000 (16:16 +0200)]
system-linux: fix a typo in gre tunnel data parsing logic

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
6 years agowireless: Add WPA-EAP-SUITE-B-192 (WPA3-Enterprise)
Hauke Mehrtens [Tue, 9 Oct 2018 20:57:52 +0000 (22:57 +0200)]
wireless: Add WPA-EAP-SUITE-B-192 (WPA3-Enterprise)

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
6 years agowireless: Add Opportunistic Wireless Encryption (OWE)
Hauke Mehrtens [Tue, 9 Oct 2018 20:57:13 +0000 (22:57 +0200)]
wireless: Add Opportunistic Wireless Encryption (OWE)

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
6 years agowireless: Add Simultaneous Authentication of Equals (SAE)
Hauke Mehrtens [Thu, 4 Oct 2018 20:34:48 +0000 (22:34 +0200)]
wireless: Add Simultaneous Authentication of Equals (SAE)

This adds PSK3 / SAE support.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
6 years agoiprule: coding style fixes
Hans Dedecker [Mon, 1 Oct 2018 20:24:26 +0000 (22:24 +0200)]
iprule: coding style fixes

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
6 years agoiprule: fix segfault (FS#1875)
Hans Dedecker [Mon, 1 Oct 2018 15:52:01 +0000 (17:52 +0200)]
iprule: fix segfault (FS#1875)

Fix segfault in generic_interface_cb by checking the
IPRULE_OUT/IPRULE_IN flags before doing the strcmp for the possible
configured out/in interface(s) of the ip rule.
Also don't copy the interface layer3 device as the layer 3 device is
not yet known when IFEV_CREATE event is launched.
The layer3 device will be known when the IFEV_UP event is processed in
rule_out_cb/rule_in_cb.

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
6 years agoscripts: fix previous commit
Jo-Philipp Wich [Wed, 19 Sep 2018 14:55:00 +0000 (16:55 +0200)]
scripts: fix previous commit

Actually change the glob pattern as described in the previous commit.

Fixes: 3c8ac1c ("netifd: fix wpa mixed mode matching")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
6 years agonetifd: fix wpa mixed mode matching
Rick Farina (Zero_Chaos) [Wed, 19 Sep 2018 14:43:42 +0000 (10:43 -0400)]
netifd: fix wpa mixed mode matching

Change wpa mixed mode matching to not accidently catch wep+mixed.

All documented cases have the character between {wpa,psk} and mixed as a
'-' but no need to break things which were working, so preserve the *
case.

Reported-by: "Rick Farina (Zero_Chaos)" <zerochaos@gentoo.org>
[Allow "psk-mixed" to be prefixed, to align with the *psk2* and *psk* cases,
 slightly reword subject and commit message.]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
6 years agosystem-linux: enable by default ignore encaplimit for ip6 tunnels
Hans Dedecker [Mon, 17 Sep 2018 19:41:16 +0000 (21:41 +0200)]
system-linux: enable by default ignore encaplimit for ip6 tunnels

Enable ignore encaplimit by default for ip6 tunnels as not all ISPs support
the destination option header containing the tunnel encapsulation limit
resulting into broken map/ds-lite connectivity.
Setting the ignore encaplimit flag by default is a more sane setting as it
avoids user configuation of the encaplimit uci option for ds-lite/map tunnels
in case of broken connectivity.

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
6 years agoCMakeList: Check that compiler supports -Wimplicit-fallthrough
Florian Fainelli [Wed, 12 Sep 2018 00:14:19 +0000 (17:14 -0700)]
CMakeList: Check that compiler supports -Wimplicit-fallthrough

This is a GCC >= 7 feature, not all compilers support it.

Fixes: 908a9f4f1027 ("CMakeLists.txt: add -Wimplicit-fallthrough to the compiler flags")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
6 years agointerface: let interface_set_down() return void
Hans Dedecker [Mon, 20 Aug 2018 12:28:00 +0000 (14:28 +0200)]
interface: let interface_set_down() return void

Let interface_set_down() return void as no usefull error code
is returned by __interface_set_down()

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
6 years agointerface: make __interface_set_down() static
Hans Dedecker [Mon, 20 Aug 2018 12:21:06 +0000 (14:21 +0200)]
interface: make __interface_set_down() static

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
6 years agointerface: extend interface error messages in interface_set_up()
Hans Dedecker [Mon, 20 Aug 2018 11:53:17 +0000 (13:53 +0200)]
interface: extend interface error messages in interface_set_up()

Don't return an error code in interface_set_up as it's ignored anyway by the
calling functions; but rather add more interface error messages so the actual
problem is visible for the user by doing ifstatus <interface>

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
6 years agointerface: ensure NO_DEVICE error is always reported
Hans Dedecker [Fri, 17 Aug 2018 13:55:00 +0000 (15:55 +0200)]
interface: ensure NO_DEVICE error is always reported

Remove interface available checks in the functions interface_start_pending
and interface_handle_config_change so the NO_DEVICE error is reported in
ifstatus <interface> making it clear to the user the configured device in
ifname is not found

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
6 years agodevice: gracefully handle device names exceeding IFNAMESIZ
Hans Dedecker [Sun, 12 Aug 2018 20:08:22 +0000 (22:08 +0200)]
device: gracefully handle device names exceeding IFNAMESIZ

Instead of truncating the device name when it exceeds IFNAMSIZ length;
let device_set_ifname return an error code and do not add the device
to the device list.
This avoids possible issues with device names becoming identical due the
truncation and as a result unexpected behavior.
Further let the different device types gracefully handle the error code
returned by device_init

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
6 years agointerface-ip: always override downstream IPv6 mtu
Hans Dedecker [Sun, 5 Aug 2018 12:46:22 +0000 (14:46 +0200)]
interface-ip: always override downstream IPv6 mtu

Always override the downstream IPv6 mtu in case it differs with the IPv6 mtu
of the upstream link. This allows to increase the downstream IPv6 mtu in
case RA messages are received on the upstream link having a mtu attribute
higher than the downstream IPv6 mtu.
At the same be verbose when failing to set the IPv6 mtu on the downstream link.

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
6 years agofix compile error
John Crispin [Mon, 30 Jul 2018 21:52:06 +0000 (23:52 +0200)]
fix compile error

netifd-2018-07-30-75ee7905/interface-ip.c:724:11: error: unused variable 'macaddr' [-Werror=unused-variable]

Signed-off-by: John Crispin <john@phrozen.org>
6 years agointerface-ip: fix eui64 ifaceid generation (FS#1668)
Hans Dedecker [Mon, 30 Jul 2018 19:19:47 +0000 (21:19 +0200)]
interface-ip: fix eui64 ifaceid generation (FS#1668)

Use the mac address stored in the device_settings struct to generate the
eui64 ifaceid as the interface layer3 device does not contain a mac address
for non bridge interfaces

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
6 years agonetifd: make sure the vlan ifname fits into the buffer
John Crispin [Mon, 16 Jul 2018 08:32:08 +0000 (10:32 +0200)]
netifd: make sure the vlan ifname fits into the buffer

Signed-off-by: John Crispin <john@phrozen.org>
6 years agoiprule: remove bogus assert calls
Felix Fietkau [Wed, 25 Jul 2018 08:44:27 +0000 (10:44 +0200)]
iprule: remove bogus assert calls

Signed-off-by: Felix Fietkau <nbd@nbd.name>
6 years agoiprule: fix broken in_dev/out_dev checks
Felix Fietkau [Wed, 25 Jul 2018 08:43:41 +0000 (10:43 +0200)]
iprule: fix broken in_dev/out_dev checks

Since they are both char arrays, they can never be NULL

Signed-off-by: Felix Fietkau <nbd@nbd.name>
6 years agovlan: use alloca to get rid of IFNAMSIZE in vlan_dev_set_name()
Hans Dedecker [Mon, 16 Jul 2018 21:03:25 +0000 (23:03 +0200)]
vlan: use alloca to get rid of IFNAMSIZE in vlan_dev_set_name()

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
6 years agoubus: display correct prefix size for IPv6 prefix address
Hans Dedecker [Mon, 16 Jul 2018 12:31:47 +0000 (14:31 +0200)]
ubus: display correct prefix size for IPv6 prefix address

Make sure the displayed prefix size is identical to the kernel installed
prefix size for local IPv6 prefix addresses

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
6 years agoCMakeLists.txt: add -Wimplicit-fallthrough to the compiler flags
Alexander Couzens [Thu, 5 Jul 2018 01:13:03 +0000 (03:13 +0200)]
CMakeLists.txt: add -Wimplicit-fallthrough to the compiler flags

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Acked-by: Hans Dedecker <dedeckeh@gmail.com>
6 years agoproto-shell.c: add a explicit "fall through" comment to make the compiler happy
Alexander Couzens [Thu, 5 Jul 2018 01:12:26 +0000 (03:12 +0200)]
proto-shell.c: add a explicit "fall through" comment to make the compiler happy

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Acked-by: Hans Dedecker <dedeckeh@gmail.com>
6 years agoreplace fall throughs in switch/cases where possible with simple code changes
Alexander Couzens [Fri, 29 Jun 2018 02:30:13 +0000 (04:30 +0200)]
replace fall throughs in switch/cases where possible with simple code changes

fall throughs are usually error-prone, especially when someone else extend
it.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Acked-by: Hans Dedecker <dedeckeh@gmail.com>
6 years agoiprule: rework interface based rules to handle dynamic interfaces
Alexander Couzens [Fri, 29 Jun 2018 21:15:28 +0000 (23:15 +0200)]
iprule: rework interface based rules to handle dynamic interfaces

Previous netifd would only apply `ip rule`s while config phase.
If the iprule is depending on an interface (iif or oif), the rule
will fail if the interface is not up.

Allow iprules to track interfaces and their devices by using
the interface events.

Fixes: FS#1571
Acked-by: Hans Dedecker <dedeckeh@gmail.com>
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
6 years agoIntroduce new interface event "create" (IFEV_CREATE)
Alexander Couzens [Fri, 29 Jun 2018 03:23:14 +0000 (05:23 +0200)]
Introduce new interface event "create" (IFEV_CREATE)

"create" will be called before the proto handlers initialised.

Acked-by: Hans Dedecker <dedeckeh@gmail.com>
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
6 years agosystem-linux: fix build error on older kernels
Felix Fietkau [Wed, 4 Jul 2018 19:15:58 +0000 (21:15 +0200)]
system-linux: fix build error on older kernels

Add an #ifdef guard around 56000base* definitions, which don't exist on
Linux 3.18

Signed-off-by: Felix Fietkau <nbd@nbd.name>
6 years agosystem-linux: adjust bridge isolate mode for upstream attribute naming
Felix Fietkau [Wed, 4 Jul 2018 17:48:03 +0000 (19:48 +0200)]
system-linux: adjust bridge isolate mode for upstream attribute naming

Signed-off-by: Felix Fietkau <nbd@nbd.name>
6 years agosystem-linux: extend link mode speed definitions
Hans Dedecker [Tue, 3 Jul 2018 13:49:18 +0000 (15:49 +0200)]
system-linux: extend link mode speed definitions

Add all available link mode speed definitions as defined in ethtool.h

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
6 years agosystem-linux: add autoneg and link-partner output
Joe Holden [Wed, 27 Jun 2018 21:14:33 +0000 (22:14 +0100)]
system-linux: add autoneg and link-partner output

This adds an array that contains the link modes advertised by the other device and also
indicates whether auto negotiation is true or false.

link-partner may or may not be populated depending on hardware, driver and/or settings.

Signed-off-by: Joe Holden <jwh@zorins.co.uk>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
6 years agosystem-linux: make encaplimit configurable for ip6 tunnels (FS#1501)
Hans Dedecker [Tue, 29 May 2018 20:40:00 +0000 (22:40 +0200)]
system-linux: make encaplimit configurable for ip6 tunnels (FS#1501)

Make encapsulation limit of IP6 tunnels configurable for the ds-lite/map
proto shell handlers as not all ISPs support the destination option header
containing the tunnel encapsulation limit value as reported in FS#1501.

The IP6 tunnel specific setting encaplimit is parsed as a nested json
data object; setting it to ignore disables the insertion of the
destination option header while a value from 0 till 255 sets the
tunnel encapsulation limit accordingly in the destination option header.

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
6 years agonterface-ip: remove superfluous iface check in interface_ip_set_enabled()
Hans Dedecker [Thu, 26 Apr 2018 20:40:24 +0000 (22:40 +0200)]
nterface-ip: remove superfluous iface check in interface_ip_set_enabled()

No need to check iface pointer in interface_ip_set_enabled as the
interface is always set by the function __interface_ip_init().
Reported by Coverity in CID 1330437

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
6 years agosystem-linux: fix strncpy bounds
Hans Dedecker [Sun, 22 Apr 2018 20:23:49 +0000 (22:23 +0200)]
system-linux: fix strncpy bounds

Fix strncpy bounds as reported by Coverity in CID 14349881328977,
13289531328952132895113289501328949 and 1328944.

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
6 years agowireless: include noscan option in common wdev vars
Daniel Golle [Fri, 20 Apr 2018 05:27:16 +0000 (07:27 +0200)]
wireless: include noscan option in common wdev vars

'noscan' can be passed down to wpa_supplicant to enforce channel
settings in mesh mode. Allow hostapd.sh to take care of it.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
6 years agosystem-linux: check ioctl return value in system_vlan()
Hans Dedecker [Mon, 16 Apr 2018 11:02:28 +0000 (13:02 +0200)]
system-linux: check ioctl return value in system_vlan()

Detected by Coverity in CID 1433754

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
6 years agosystem-linux: check ioctl return value in system_if_flags()
Hans Dedecker [Sat, 14 Apr 2018 19:15:42 +0000 (21:15 +0200)]
system-linux: check ioctl return value in system_if_flags()

Detected by Coverity in CID 1433760

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
6 years agosystem-linux: fix segfault on alloc failure in system_if_check()
Hans Dedecker [Sat, 14 Apr 2018 19:05:25 +0000 (21:05 +0200)]
system-linux: fix segfault on alloc failure in system_if_check()

Detected by Coverity in CID 1433686

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
6 years agosystem-linux: fix segfault on error in system_add_ip6_tunnel()
Hans Dedecker [Sat, 14 Apr 2018 18:58:42 +0000 (20:58 +0200)]
system-linux: fix segfault on error in system_add_ip6_tunnel()

Detected by Coverity in CID 1430884

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
6 years agohandler: fix resource leak on error in netifd_init_script_handlers()
Hans Dedecker [Thu, 12 Apr 2018 20:46:35 +0000 (22:46 +0200)]
handler: fix resource leak on error in netifd_init_script_handlers()

Detected by Coverity in CID 1412486

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
6 years agosystem-linux: remove unnecessary open call in system_if_dump_info()
Hans Dedecker [Thu, 12 Apr 2018 20:36:38 +0000 (22:36 +0200)]
system-linux: remove unnecessary open call in system_if_dump_info()

Detected by coverity in CID 1329735

6 years agosystem-linux: fix memory leak on error in system_add_vxlan()
Hans Dedecker [Thu, 12 Apr 2018 20:14:52 +0000 (22:14 +0200)]
system-linux: fix memory leak on error in system_add_vxlan()

Detected by coverity in CID 1412449

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
6 years agointerface-ip: fix memory leak on error in interface_update_prefix_assignments()
Hans Dedecker [Thu, 12 Apr 2018 20:08:18 +0000 (22:08 +0200)]
interface-ip: fix memory leak on error in interface_update_prefix_assignments()

Detected by coverity in CID 141267

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
6 years agointerface: fix "ifup-failed" hotplug event handling
Martin Schiller [Tue, 10 Apr 2018 04:21:39 +0000 (06:21 +0200)]
interface: fix "ifup-failed" hotplug event handling

The ifup-failed event should only be triggered when the former
interface state is IFS_SETUP.

Otherwise, there will also be an ifup-failed event in the
IFS_TEARDOWN stateif you do an manual ifdown <IFC>.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
6 years agointerface-ip: fix memory leak in interface_ip_add_target_route()
Hans Dedecker [Sun, 1 Apr 2018 10:21:38 +0000 (12:21 +0200)]
interface-ip: fix memory leak in interface_ip_add_target_route()

Commit 9c8d781 introduced a memory leak in interface_ip_add_target_route
in case interface_ip_find_addr_target returns true for a given address
by not freeing the previously allocated route.
While at it rework the logic so a host route is only allocated when it's
really required.

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
6 years agonetifd: return the interface for locally addressable host dependencies (FS#1452)
Felix Fietkau [Tue, 27 Mar 2018 09:28:54 +0000 (11:28 +0200)]
netifd: return the interface for locally addressable host dependencies (FS#1452)

Fixes an issue where interfaces with host dependencies that resolve to a
local subnet stay down.

Fixes: 1f5a29c3de6e ("ip: do not add local routes for host dependencies")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
6 years agointerface-ip: fix route selection for host dependencies
Felix Fietkau [Tue, 13 Mar 2018 12:05:28 +0000 (13:05 +0100)]
interface-ip: fix route selection for host dependencies

In order to find the best match, allow overriding the last found entry
if route->mask for the new entry is bigger than the one from the previous
entry.

Patch submitted by 'Mikael' in FS#1358

Signed-off-by: Felix Fietkau <nbd@nbd.name>
6 years agodevice: add support for setting the isolate options for bridge ports
Felix Fietkau [Tue, 13 Mar 2018 11:52:43 +0000 (12:52 +0100)]
device: add support for setting the isolate options for bridge ports

Signed-off-by: Felix Fietkau <nbd@nbd.name>
6 years agoip: do not add local routes for host dependencies
Felix Fietkau [Wed, 7 Mar 2018 22:14:57 +0000 (23:14 +0100)]
ip: do not add local routes for host dependencies

This avoids creating invalid routes in cases where another daemon is
handling local routes for an interface, e.g. on mesh interfaces

Signed-off-by: Felix Fietkau <nbd@nbd.name>
6 years agoremove rps/xps configuration support
Felix Fietkau [Mon, 26 Feb 2018 11:21:00 +0000 (12:21 +0100)]
remove rps/xps configuration support

It is overly complex, yet does not cover common scenarios very well.
It will be replaced with a simpler shell script that provides a better
default policy

Signed-off-by: Felix Fietkau <nbd@nbd.name>
6 years agonetifd-proto: add proto_config_add_array wrapper
Hans Dedecker [Mon, 5 Feb 2018 08:57:47 +0000 (09:57 +0100)]
netifd-proto: add proto_config_add_array wrapper

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
6 years agosystem-linux: VXLAN: add options to enable and disable UDP checksums
Matthias Schiffer [Wed, 24 Jan 2018 12:21:44 +0000 (13:21 +0100)]
system-linux: VXLAN: add options to enable and disable UDP checksums

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
6 years agoproto: allow dumping protocol handlers without config_params
Olof Sivertsson [Wed, 3 Jan 2018 09:35:13 +0000 (10:35 +0100)]
proto: allow dumping protocol handlers without config_params

When ubus invokes proto_dump_handlers, and a struct proto_handler has
been added with a NULL config_params, a segmentation fault occurs.

Avoid this segmentation fault by checking for a NULL config_params
before further access.

Signed-off-by: Olof Sivertsson <olof.sivertsson@zenterio.com>
6 years agointerface-ip: harden eui64 IPv6 prefix address generation
Hans Dedecker [Thu, 14 Dec 2017 13:13:35 +0000 (14:13 +0100)]
interface-ip: harden eui64 IPv6 prefix address generation

Check if a mac address is actually present when generating an eui64 based
IPv6 address; in case of failure bail out.
At the same time make sure the active mac address is used as input for the
eui64 based IPv6 address and guarantee IPv6 prefix address generation is
based on the actual config by resetting the IPv6 prefix address in the
assignment structure when it gets deleted.

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
6 years agointerface-ip: fix race condition in IPv6 prefix address generation
Hans Dedecker [Thu, 14 Dec 2017 13:13:34 +0000 (14:13 +0100)]
interface-ip: fix race condition in IPv6 prefix address generation

Don't generate an IPv6 prefix address without taking into account the
interface state. In case eui64 is configured to generate the ifaceid this
could fail as the layer3 device mac address could not yet be available if
the interface is not yet in setup or up state.
While at it remove the interface metric assignment as this is already done
by the function interface_set_route_info.

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
6 years agohandler: replace is_error() helper with NULL check
Alexandru Ardelean [Fri, 8 Dec 2017 14:22:13 +0000 (16:22 +0200)]
handler: replace is_error() helper with NULL check

The `is_error()` is just a macro that checks
that object is NULL (which is considered an error
in libjson-c terminology).

Newer libjson-c versions have deprecated this.

Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
7 years agointerface-ip: add missing IPv6 policy rule
Hans Dedecker [Thu, 16 Nov 2017 14:42:41 +0000 (15:42 +0100)]
interface-ip: add missing IPv6 policy rule

Commit 2f31bff38d4dc2f36006ded6b8a7d039cb569eaa added interface routing
table support; as a result for IPv6 the prefix route linked to the IPv6
address is added to the specified IPv6 interface routing table.
In order to route traffic having as destination the IPv6 prefix a policy
rule is required using the prefix destination as policy so the traffic is
passed to the correct routing table.
The IPv6 prefix address logic was not installing this policy rule effectively
breaking routing when trying to reach a global or ULA IPv6 address in the
lan from either the device or another wan device.

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
7 years agoproto: add point-to-point IPv4 address config support (FS#1037)
Hans Dedecker [Tue, 17 Oct 2017 20:16:43 +0000 (22:16 +0200)]
proto: add point-to-point IPv4 address config support (FS#1037)

Add config support support for point-to-point IPv4 addresses by providing
the uci parameter ptpaddr. This allows to support a gateway being in a
different subnet than the assigned IP by modeling the local IP having a
point-to-point address.
This is similar to the point-to-point IPv4 address support already present
for the protocol handlers.

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
7 years agoubus: display the point-to-point IPv4 address
Hans Dedecker [Tue, 17 Oct 2017 20:16:44 +0000 (22:16 +0200)]
ubus: display the point-to-point IPv4 address

Display the point-to-point IPv4 address as well when dumping
the IP address list in ubus.

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
7 years agoubus: fix ubus error code on reload failure
Hans Dedecker [Sat, 7 Oct 2017 17:46:44 +0000 (19:46 +0200)]
ubus: fix ubus error code on reload failure

Return the more approriate error code UBUS_STATUS_NOT_FOUND in case
network reload fails

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
7 years agoconfig: suppress error if no wireless config present (FS#1030)
Hans Dedecker [Fri, 6 Oct 2017 14:56:42 +0000 (16:56 +0200)]
config: suppress error if no wireless config present (FS#1030)

Wireless config is optional as not all targets have a wireless interface;
therefore don't report an error if the wireless config is missing so
network reload is not reporting an error to the user.
While at it use netifd_log_message to print an error if the config cannot
be loaded.

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
7 years agosystem-linux: add support for hotplug event 'move'
Martin Schiller [Thu, 28 Sep 2017 08:32:28 +0000 (10:32 +0200)]
system-linux: add support for hotplug event 'move'

If you rename a network interface, there is a move uevent
invoked instead of remove/add.

This patch adds support for this kind of event.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Acked-by: Hans Dedecker <dedeckeh@gmail.com>
7 years agosystem-linux: parse map-e fmrs parameters as nested data json object
Hans Dedecker [Sun, 27 Aug 2017 19:48:28 +0000 (21:48 +0200)]
system-linux: parse map-e fmrs parameters as nested data json object

Parse map-e fmrs parameters IPv6 prefix, IPv4 prefix, ealen and offset
as array elements nested in a data json object.
At the same time remove the now obsolete TUNNEL_ATTR_FMRS tunnel attribute.

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
7 years agoallow setting rps/xps defualt values via uci
John Crispin [Tue, 22 Aug 2017 07:10:58 +0000 (09:10 +0200)]
allow setting rps/xps defualt values via uci

Signed-off-by: John Crispin <john@phrozen.org>
7 years agosystem: remove unused 6rd tunnel attributes
Hans Dedecker [Mon, 21 Aug 2017 17:32:25 +0000 (19:32 +0200)]
system: remove unused 6rd tunnel attributes

Commit 7573880ac042c6e5c8d48b1ad83d357b5e02743b added support for 6rd
attributes as a nested json data object which makes the attributes
TUNNEL_ATTR_6RD_PREFIX and TUNNEL_ATTR_6RD_RELAY_PREFIX unused

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
7 years agonetifd: allow negative neighlocktime values
Alin Năstac [Thu, 17 Aug 2017 12:12:05 +0000 (14:12 +0200)]
netifd: allow negative neighlocktime values

When -1 is written in /proc/sys/net/ipv4/neigh/<iface>/locktime,
kernel disables ARP trashing protection. A value of 0 does not completely
disable this protection, a second ARP update being discarded if it
is processed during the same jiffie as the first update.

Signed-off-by: Alin Nastac <alin.nastac@gmail.com>