openwrt/staging/981213.git
2 years agomt7629 zioncom ip04398a mtk-snand
Chuanhong Guo [Sat, 9 Apr 2022 12:13:58 +0000 (20:13 +0800)]
mt7629 zioncom ip04398a

2 years agomt7622-rfb-mtk0897-ubi
Chuanhong Guo [Thu, 7 Apr 2022 02:20:40 +0000 (10:20 +0800)]
mt7622-rfb-mtk0897-ubi

2 years agomediatek: mt7629: enable fit partition
Chuanhong Guo [Sat, 9 Apr 2022 11:53:55 +0000 (19:53 +0800)]
mediatek: mt7629: enable fit partition

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2 years agomediatek: enable arm arch timer for mt7629
Chuanhong Guo [Sat, 9 Apr 2022 05:28:26 +0000 (13:28 +0800)]
mediatek: enable arm arch timer for mt7629

otherwise the system delay is completely broken.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2 years agomediatek: enable snfi for mt7629
Chuanhong Guo [Sat, 9 Apr 2022 05:26:50 +0000 (13:26 +0800)]
mediatek: enable snfi for mt7629

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2 years agomediatek: restore support for Fidelix FM35X1GA
Chuanhong Guo [Sat, 9 Apr 2022 12:18:40 +0000 (20:18 +0800)]
mediatek: restore support for Fidelix FM35X1GA

This patch was dropped when the spi-nand driver got replaced last time.
Note: This isn't a complete chip support. It's missing ECC status
functions. It's fine on MT7622 because we don't use it, but this means
it can't be upstreamed.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2 years agomediatek: add an upstreamed spi-nand driver
Chuanhong Guo [Thu, 7 Apr 2022 02:16:47 +0000 (10:16 +0800)]
mediatek: add an upstreamed spi-nand driver

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2 years agomediatek: spi-nand: check for 1 byte BBM only
Chuanhong Guo [Thu, 7 Apr 2022 02:05:56 +0000 (10:05 +0800)]
mediatek: spi-nand: check for 1 byte BBM only

the OOB layout in MTK SNFI uses the 2nd byte, and anything using OOB
will make the block a bad-block in spi-nand driver.
Hack it for now. We need a proper solution upstream.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2 years agomediatek: v5.15: backport spi-mem ecc support
Chuanhong Guo [Thu, 7 Apr 2022 02:05:25 +0000 (10:05 +0800)]
mediatek: v5.15: backport spi-mem ecc support

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2 years agomediatek: drop spi-nand driver from mtk
Chuanhong Guo [Thu, 7 Apr 2022 02:03:50 +0000 (10:03 +0800)]
mediatek: drop spi-nand driver from mtk

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2 years agokernel: mtk_bmt: skip bitflip check if threshold isn't set
Chuanhong Guo [Thu, 7 Apr 2022 01:56:02 +0000 (09:56 +0800)]
kernel: mtk_bmt: skip bitflip check if threshold isn't set

kernel spi-nand driver leaves this field empty and let mtd set it later.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2 years agokernel: v5.15: backport spi-nand supports from nand/next
Chuanhong Guo [Sat, 9 Apr 2022 12:22:36 +0000 (20:22 +0800)]
kernel: v5.15: backport spi-nand supports from nand/next

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2 years agoqosify: update to the latest version
Felix Fietkau [Fri, 8 Apr 2022 11:07:36 +0000 (13:07 +0200)]
qosify: update to the latest version

92f5e18675bf interface: fix ifname present check in interface status
ef82defaae26 ubus: add active devices to bridger blacklist

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2 years agobcm53xx: refresh kernel 5.15 config
Rafał Miłecki [Fri, 8 Apr 2022 08:49:31 +0000 (10:49 +0200)]
bcm53xx: refresh kernel 5.15 config

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2 years agofirewall4: update to latest Git HEAD
Jo-Philipp Wich [Tue, 22 Mar 2022 20:09:27 +0000 (21:09 +0100)]
firewall4: update to latest Git HEAD

a378883 fw4: fix emitting family specific redirect rules without any addrs
11feddf fw4: bracketize IPv6 addresses in dnat addr:port notation
9972f7d fw4: ensure to capitalize weekday names
fde8070 treewide: forward compatibility changes

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2 years agoucode: update to latest Git HEAD
Jo-Philipp Wich [Tue, 22 Mar 2022 19:26:59 +0000 (20:26 +0100)]
ucode: update to latest Git HEAD

33f1e0b treewide: move json-c compat shims into internal header file
e0e9431 vm: move unhandled exception reporting out of `uc_vm_execute_chunk()`
2b59140 vm: fix callframe double free on unhanded exceptions
7d7e950 main: abort when failing to load a preload library
1032a67 lib: let `json()` accept input objects implementing `read()` method
5ee68d5 fs: implement `fs.readfile()` and `fs.writefile()`
df6b861 ci: debian: change path before attempting to invoke Git operations
dfaf05a ci: debian: automatically update changelog from Git tag
34f3c45 ci: fix YAML syntax of Debian workflow
e956bcf fs: fix off-by-one in fs.dirname() function
6fc4b6c .gitignore: fix overmatching patterns, blacklist cram .venv
7c2e082 build: remove legacy json-c check
77942af build: add polyfills for older libjson-c versions
0b4aaa3 CI: build Debian package
f404285 debian: Add package definition
a37f654 types: fix escape sequence encoding of high byte values in JSON strings
aae5312 Update README.md
8134e25 build: fix symlink install target
87c7296 treewide: replace some leftover "utpl" occurrences, update .gitignore
7d27ad5 build: only stage ucc symlink if compile support is enabled
171402f lib: add date and time related functions
8b5dc60 lib: provide API function to obtain stdlib function implementations
eb0d2f1 main: turn ucode into multicall executable
28ee7e1 uloop: add support for tasks
753dea9 CI: build on macOS
668c5c0 lib: add argument position support (`%m$`) to `sprintf()` and `printf()`
ab46fdf treewide: remove legacy json-c include directives
b8f49b1 tests: 21_regex_literals: generalize syntax error test case
fd2e5e7 tests: 16_sort: fix logic flaw exposed on OS X
2c71bf2 tests: run_tests.sh: pass dummy value to `-T` flag
55c4a90 lib: disallow zero padding for %s formats
0d05cb5 tests: run_tests.sh: use greadlink if available
271e520 resolv: make OS X compatible
d13c320 fs: avoid Linux specific sys/sysmacros.h include on OS X
33397a3 uloop: use execvp() on OS X
bafdc8f lib: add naive sigtimedwait() stub for OS X
ada1585 build: consolidate CMakeLists.txt and cover OS X deviations
befbb69 include: add OS X compatible endian.h header
49838a8 include: rename include guards to avoid clashes with system headers
91f65de nl80211: add missing attributes and correct some attribute flags
b4a1fd5 lib: adjust require(), render() and include() raw mode semantics
4618807 main: rework CLI frontend
73dcd78 lib: fix potential integer underflow on empty render output
c402551 vm: fix crash on object literals with non-string computed properties
efe8a02 syntax: support add new operators
078d686 ubus: add event support
6c66c83 ubus: refactor error and argument handling
1cb04f9 ubus: add object publishing, notify and subscribe support
0e85974 uloop: clear errno before integer conversion attempts
05bd7ed types: treat resource type prototypes as GC roots
a2a26ca lib: introduce uloop binding
6b6d01f vm: release this context on exception in managed method call
1af23a9 tests: fix proto() testcase
4ce69a8 fs: implement access(), mkstemp(), file.flush() and proc.flush()

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2 years agohostapd: add ubus link-measurements notifications
David Bauer [Thu, 31 Mar 2022 20:39:04 +0000 (22:39 +0200)]
hostapd: add ubus link-measurements notifications

Notify external ubus subscribers of received link-measurement reports.

Signed-off-by: David Bauer <mail@david-bauer.net>
2 years agohostapd: add ubus method for requesting link measurements
David Bauer [Tue, 29 Mar 2022 22:31:26 +0000 (00:31 +0200)]
hostapd: add ubus method for requesting link measurements

Add a ubus method to request link-measurements from connected STAs.

In addition to the STAs address, the used and maximum transmit power can
be provided by the external process for the link-measurement. If they
are not provided, 0 is used as the default value.

Signed-off-by: David Bauer <mail@david-bauer.net>
2 years agohostapd: add support for enabling link measurements
David Bauer [Thu, 31 Mar 2022 16:06:02 +0000 (18:06 +0200)]
hostapd: add support for enabling link measurements

Allow external processes to enable advertisement of link-measurement RRM
capability.

Signed-off-by: David Bauer <mail@david-bauer.net>
2 years agoat91: Automatically detect USB feature
Hauke Mehrtens [Wed, 6 Apr 2022 22:36:25 +0000 (00:36 +0200)]
at91: Automatically detect USB feature

The sama7 sub target does not have USB support, the feature should not
be activated there. OpenWrt can automatically detect if the target
supports USB by using the scripts/target-metadata.pl script. With the
automatic detection USB support will only get activated on subtargest
which actually support USB like sam9x and sama5.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2 years agoat91/sama7: Do not build in Bluetooth
Hauke Mehrtens [Tue, 5 Apr 2022 20:28:30 +0000 (22:28 +0200)]
at91/sama7: Do not build in Bluetooth

Bluetooth should be activated as an optional kmod package instead of
compiling it into the kernel.

Tested-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2 years agoat91/sama7: Use ext4 driver for ext2 and ext3
Hauke Mehrtens [Tue, 5 Apr 2022 20:27:41 +0000 (22:27 +0200)]
at91/sama7: Use ext4 driver for ext2 and ext3

Use the ext4 driver for ext2 and ext3 too. This feature is activated in
the OpenWrt generic configuration.

Tested-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2 years agoat91/sama7: Deactivate certification and key system
Hauke Mehrtens [Tue, 5 Apr 2022 20:24:00 +0000 (22:24 +0200)]
at91/sama7: Deactivate certification and key system

This was probably activated by mac80211 which was activated before.
mac80211 is build from backports in OpenWrt.

Tested-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2 years agoat91/sama7: Do not activate cgroups and namespaces
Hauke Mehrtens [Tue, 5 Apr 2022 20:22:04 +0000 (22:22 +0200)]
at91/sama7: Do not activate cgroups and namespaces

cgroups and namespaces should be configured by the generic OpenWrt
configuration and not for a specific target.

Tested-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2 years agoat91/sama7: Remove config options build as module
Hauke Mehrtens [Tue, 5 Apr 2022 20:14:16 +0000 (22:14 +0200)]
at91/sama7: Remove config options build as module

Remove the configuration options which are building modules for the sub
target configuration.

These kernel modules are not packaged. Kernel options should only be
build as a module when they are selected by a kmod package and not by
setting them to =m in the target kernel configuration.

Tested-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2 years agokernel: remove duplicate patch that is already in the 5.15 kernel tree
Felix Fietkau [Thu, 7 Apr 2022 11:07:30 +0000 (13:07 +0200)]
kernel: remove duplicate patch that is already in the 5.15 kernel tree

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2 years agomt76: update to the latest version
Felix Fietkau [Thu, 7 Apr 2022 10:23:52 +0000 (12:23 +0200)]
mt76: update to the latest version

5beb87716e70 mt76: dma: add wrapper macro for accessing queue registers
e0bc736d5617 mt76: add support for overriding the device used for DMA mapping
b8c842daa081 mt76: make number of tokens configurable dynamically
87a962e0608f mt76: mt7915: add Wireless Ethernet Dispatch support
2accb74e6be3 mt76: mt7915: fix using null pointer when wfsys on
e5227f2f3120 mt76: mt7921: Fix the error handling path of mt7921_pci_probe()
ec0e9f4da32f mt76: mt7915: fix possible uninitialized pointer dereference in mt7986_wmac_gpio_setup
5a87be892ba7 mt76: mt7915: fix possible NULL pointer dereference in mt7915_mac_fill_rx_vector
fe441e5d3dcf mt76: mt7915: do not pass data pointer to mt7915_mcu_muru_debug_set
f3ddfe886283 mt76: mt7915: report rx mode value in mt7915_mac_fill_rx_rate
2a0d370cb5fe mt76: mt7915: use 0xff to initialize bitrate_mask in mt7915_init_bitrate_mask
506bb0605e3e mt76: mt7921: Add AP mode support

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2 years agoubox: add example /etc/modules.conf + conffiles entry
Felix Fietkau [Thu, 7 Apr 2022 10:01:44 +0000 (12:01 +0200)]
ubox: add example /etc/modules.conf + conffiles entry

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2 years agobcm27xx: include 'rtc' in target's 'FEATURES'
Piotr Dymacz [Wed, 6 Apr 2022 21:07:55 +0000 (23:07 +0200)]
bcm27xx: include 'rtc' in target's 'FEATURES'

There are many ways to add external RTC to Raspberry Pi boards. Let's
include support for this for the whole target and while at it, sort
features alphabetically.

Fixes: #9594
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2 years agouboot-imx: build 'u-boot-dtb.img' for SolidRun CuBox-i
Piotr Dymacz [Fri, 1 Apr 2022 13:11:37 +0000 (15:11 +0200)]
uboot-imx: build 'u-boot-dtb.img' for SolidRun CuBox-i

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2 years agoimx: image: use 'u-boot-dtb.img' filename for SPL payload
Piotr Dymacz [Fri, 1 Apr 2022 13:11:36 +0000 (15:11 +0200)]
imx: image: use 'u-boot-dtb.img' filename for SPL payload

For targets in U-Boot which were migrated to DM, the correct binary
image filename will be 'u-boot-dtb.img'. For backward compatibility,
keep support for both files and use the one which was generated with
our 'uboot-imx' package.

See also 'CONFIG_SPL_FS_LOAD_PAYLOAD_NAME' and 'CONFIG_OF_CONTROL' in
mainline U-Boot sources.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2 years agoimx: bootscript-apalis: make it working with U-Boot 2022.01
Petr Štetiar [Fri, 1 Apr 2022 13:11:35 +0000 (15:11 +0200)]
imx: bootscript-apalis: make it working with U-Boot 2022.01

Upstream in commit 8b9c0cb46471 ("apalis_imx6: boot env configuration
updates") removed emmc legacy wrappers, but so far didn't included any
replacements. Fix it by simply defining the missing variables and UUID
gathering directly into the boot script.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
[pepe2k@gmail.com: updated commit title for 2022.01]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2 years agouboot-imx: bump to 2022.01 release
Piotr Dymacz [Fri, 1 Apr 2022 13:11:34 +0000 (15:11 +0200)]
uboot-imx: bump to 2022.01 release

Two patches were removed because of the changes introduced in upstream:

1. 110-mx6cuboxi-mmc-fallback.patch
Looks like similar changes were introduced in 6c3fbf3e456c ("mx6cuboxi:
customize board_boot_order to access eMMC").

2. 111-mx6cuboxi_defconfig-force-mmc-boot.patch
The 'CONFIG_SPL_FORCE_MMC_BOOT' was removed in 15aec318ef03 ("Revert
"imx: Introduce CONFIG_SPL_FORCE_MMC_BOOT to force MMC boot on falcon
mode").

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2 years agokernel: add missing CONFIG_SECURITY_LANDLOCK symbol for 5.15
Daniel Golle [Wed, 6 Apr 2022 19:04:22 +0000 (20:04 +0100)]
kernel: add missing CONFIG_SECURITY_LANDLOCK symbol for 5.15

Building with SELinux enabled unveiled a missing Kconfig symbol.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2 years agolibselinux: add missing host-build dependency on libsepol/host
Daniel Golle [Wed, 6 Apr 2022 18:59:52 +0000 (19:59 +0100)]
libselinux: add missing host-build dependency on libsepol/host

The host-build of libselinux requires libsepol/host.
Add the libsepol/host to HOST_BUILD_DEPENDS to allow build on hosts
which don't have libsepol installed.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2 years agoscripts: make sure sort-order is independent from locale
Daniel Golle [Wed, 6 Apr 2022 16:25:16 +0000 (17:25 +0100)]
scripts: make sure sort-order is independent from locale

Set LC_ALL=C environment variable when calling 'sort' as the sort
order otherwise depends on the locale set.

Fixes: 56ce110b73 ("scripts: make sure conffiles are sorted")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2 years agodnsmasq: add procd interface index tracking
Valentyn Datsko [Wed, 6 Apr 2022 13:13:13 +0000 (16:13 +0300)]
dnsmasq: add procd interface index tracking

Problem exist when dnsmasq is exclusively bind to particular interface.
After reconfiguring or restarting this interface, its index changes, but
dnsmasq uses the old one. When this problem occurs, dnsmasq does not
listen on the correct interface so DHCP does not work, and clients do not
get an IP address. Procd netdev param can be added to restart dnsmasq when
the interface index is changed.

Signed-off-by: Valentyn Datsko <valikk.d@gmail.com>
[combined into a single &&-connected statement]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2 years agobridger: add bridge forwarding accelerator
Felix Fietkau [Wed, 6 Apr 2022 12:09:34 +0000 (14:09 +0200)]
bridger: add bridge forwarding accelerator

This package uses BPF to create a fast path which improves bridging performance
by bypassing the bridge layer. It also supports creating tc offload rules for
hardware that supports it.
Hardware offload support can be used with MT7622 + MT7915 once it is merged

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2 years agokernel: set SOURCE_DATE_EPOCH for initramfs root dir
Daniel Golle [Wed, 6 Apr 2022 11:19:31 +0000 (12:19 +0100)]
kernel: set SOURCE_DATE_EPOCH for initramfs root dir

Make sure the timestamp of the root directory of the initramfs is set
to SOURCE_DATE_EPOCH as well.

Fixes: 29d7461d11 ("kernel: set options to make external initramfs reproducible")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2 years agoqosify: update to the latest version
Felix Fietkau [Tue, 5 Apr 2022 19:27:40 +0000 (21:27 +0200)]
qosify: update to the latest version

Replace the tc-full dependency with tc + libnl-tiny

1cd5e12eecdc loader/interface: attach bpf program directly using netlink

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2 years agoubox: update to the latest version
Felix Fietkau [Tue, 5 Apr 2022 15:32:40 +0000 (17:32 +0200)]
ubox: update to the latest version

b87a4fdca634 kmodloader: support loading module options and blacklist from /etc/modules.conf

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2 years agokernel: package mhi mbim driver
Koen Vandeputte [Tue, 5 Apr 2022 13:07:36 +0000 (15:07 +0200)]
kernel: package mhi mbim driver

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2 years agokernel: package mhi wwan ctrl driver
Koen Vandeputte [Tue, 5 Apr 2022 13:05:02 +0000 (15:05 +0200)]
kernel: package mhi wwan ctrl driver

MHI WWAN CTRL allows QCOM-based PCIe modems to expose different modem
control protocols/ports to userspace, including AT, MBIM, QMI, DIAG
and FIREHOSE. These protocols can be accessed directly from userspace
(e.g. AT commands) or via libraries/tools (e.g. libmbim, libqmi, libqcdm)

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2 years agokernel: package mhi network driver
Koen Vandeputte [Fri, 1 Apr 2022 08:50:46 +0000 (10:50 +0200)]
kernel: package mhi network driver

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2 years agokernel: package mhi pci driver
Koen Vandeputte [Tue, 5 Apr 2022 12:53:01 +0000 (14:53 +0200)]
kernel: package mhi pci driver

This driver provides MHI PCI controller driver for devices
such as Qualcomm SDX55 based PCIe modems

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2 years agokernel: package mhi bus driver
Koen Vandeputte [Fri, 1 Apr 2022 08:50:25 +0000 (10:50 +0200)]
kernel: package mhi bus driver

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2 years agoath79: mikrotik: enable ecc hamming algorithm for kernel 5.15
Koen Vandeputte [Tue, 5 Apr 2022 11:52:25 +0000 (13:52 +0200)]
ath79: mikrotik: enable ecc hamming algorithm for kernel 5.15

This algorithm has it's own symbol now.
Enable it to fix nand support

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2 years agoath79: mikrotik: add 5.15 support for mikrotik subtarget
Koen Vandeputte [Tue, 5 Apr 2022 11:53:20 +0000 (13:53 +0200)]
ath79: mikrotik: add 5.15 support for mikrotik subtarget

Tested on RB922

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2 years agokernel: add missing symbol for 5.15
Koen Vandeputte [Tue, 5 Apr 2022 10:28:42 +0000 (12:28 +0200)]
kernel: add missing symbol for 5.15

Driver for the National Semiconductor DP83640 PHYTER (DP83640_PHY) [N/m/y/?] (NEW)

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2 years agoath79: fix ar934x spi driver delays
Oskari Lemmela [Wed, 26 Jan 2022 06:38:43 +0000 (08:38 +0200)]
ath79: fix ar934x spi driver delays

Backport spi driver delay fixes from the 5.17-rc1 kernel.

Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
[port also to kernel 5.15]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2 years agoCI: usability improvements for tools
Paul Spooren [Wed, 30 Mar 2022 00:43:17 +0000 (01:43 +0100)]
CI: usability improvements for tools

* Always store build logs
* Store .config as an artifact
* Rename job to `tools-{ os }` for log archive without spaces
* Run CI job on changes to the CI file itself

Signed-off-by: Paul Spooren <mail@aparcar.org>
2 years agobpf-headers: update to linux 5.15
Felix Fietkau [Mon, 4 Apr 2022 15:48:57 +0000 (17:48 +0200)]
bpf-headers: update to linux 5.15

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2 years agogrub2: add missing license
Paul Spooren [Mon, 4 Apr 2022 11:17:25 +0000 (13:17 +0200)]
grub2: add missing license

The PKG_LICENSE field was missing.
While at it, normalize the Makefile a bit.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2 years agoqoriq: enable support for Marvell Alaska PHYs
Stijn Tintel [Sun, 3 Apr 2022 18:31:19 +0000 (21:31 +0300)]
qoriq: enable support for Marvell Alaska PHYs

The WatchGuard Firebox M200 and M300 use a Marvell 88e1543 PHY for the
first 3 ethernet ports. This PHY is supported by the Marvell Alaska PHY
driver, so enable it.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2 years agoRevert "kernel: backport MT7530 VLAN fix"
Stijn Tintel [Sun, 3 Apr 2022 16:08:45 +0000 (19:08 +0300)]
Revert "kernel: backport MT7530 VLAN fix"

There are various reports on Github and in the forum that this commit
causes multiple problems.

This reverts commit ee6ba216d8ba1b02154c287e64d709a8bc7b0054.

Fixes: #9420
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2 years agokernel: load device-mapper early on boot
Daniel Golle [Sun, 3 Apr 2022 15:19:31 +0000 (16:19 +0100)]
kernel: load device-mapper early on boot

Previously commit openwrt/packages@3abb7cb ("lvm2: Added script and updated Makefile[...]")
couldn't actually work and allow rootfs_data to be stored on a LVM2 as
the necessary kernel modules had not been loaded at this point.
Fix this by loading device-mapper modules early at boot.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2 years agoocteon: Introduce 5.15 testing kernel
Donald Hoskins [Fri, 1 Apr 2022 04:30:53 +0000 (00:30 -0400)]
octeon: Introduce 5.15 testing kernel

octeon/patches-5.10 -> octeon/patches-5.15
Removed 140-octeon_e300_support.patch as E300 support appears to be upstreamed.
Reworked 130-add_itus_support.patch to compensate for the upstreaming of E300

octeon/config-5.15
The following Kernel Symbols were ADDED:
Line 5: +CONFIG_AF_UNIX_OOB=y
Line 6: +CONFIG_AHCI_OCTEON=y
Line 9: +CONFIG_ARCH_KEEP_MEMBLOCK=y
Line 16: +CONFIG_ATA=y
Line 17: +CONFIG_BINARY_PRINTF=y
Line 29: +CONFIG_CPU_R4K_FPU=y
Line 45: +CONFIG_FWNODE_MDIO=y
Line 51: +CONFIG_GENERIC_FIND_FIRST_BIT=y
Line 59: +CONFIG_GLOB=y
Line 61: +CONFIG_GPIO_CDEV=y
Line 77: +CONFIG_LTO_NONE=y
Line 85: +CONFIG_MIPS_FP_SUPPORT=y
Line 93: +CONFIG_NET_SELFTESTS=y
Line 94: +CONFIG_NET_SOCK_MSG=y
Line 105: +CONFIG_PATA_OCTEON_CF=y
Line 106: +CONFIG_PATA_TIMINGS=y
Line 114: +CONFIG_PTP_1588_CLOCK_OPTIONAL=y
Line 121: +CONFIG_SATA_AHCI_PLATFORM=y
Line 122: +CONFIG_SATA_HOST=y
Line 124: +CONFIG_SCSI_COMMON=y
Line 132: +CONFIG_SOCK_RX_QUEUE_MAPPING=y
Line 157: +CONFIG_USB_XHCI_HCD=y
Line 158: +CONFIG_USB_XHCI_PLATFORM=y

The following kernel symbols were REMOVED:
Line 21: -CONFIG_BLK_SCSI_REQUEST=y
Line 37: -CONFIG_ENABLE_MUST_CHECK=y
Line 69: -CONFIG_HOLES_IN_ZONE=y
Line 102: -CONFIG_OF_NET=y
Line 140: -CONFIG_SYS_SUPPORTS_HUGETLBFS=y

Compiled for Itus Shield, Boots successfully, continuing to test
for existing 5.10 memory leak.

Signed-off-by: Donald Hoskins <grommish@gmail.com>
[refresh patches]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2 years agoRevert "octeon: mark source-only"
Stijn Tintel [Sun, 3 Apr 2022 02:24:17 +0000 (05:24 +0300)]
Revert "octeon: mark source-only"

The memory leak is fixed by the kernel patches backported in the
previous commit.

This reverts commit 1fa8780056a8c7a2e26c8b4d5e6979232f117349.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2 years agokernel: backport pgalloc memory leak fix
Stijn Tintel [Sun, 3 Apr 2022 02:14:06 +0000 (05:14 +0300)]
kernel: backport pgalloc memory leak fix

Backport a fix for the massive memory leak observed in Octeon after
switching to kernel 5.10.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2 years agokernel: add missing symbol
Stijn Tintel [Sat, 2 Apr 2022 20:41:27 +0000 (23:41 +0300)]
kernel: add missing symbol

Enabling KERNEL_KPROBES exposes KERNEL_BPF_KPROBE_OVERRIDE. Add a build
option for it to fix build failures with KERNEL_KPROBES enabled.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2 years agobpf-headers: support CONFIG_HZ=300
Felix Fietkau [Fri, 25 Mar 2022 11:14:40 +0000 (12:14 +0100)]
bpf-headers: support CONFIG_HZ=300

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2 years agoimx: base-files: drop redundant space after case keywords
Piotr Dymacz [Mon, 14 Mar 2022 13:39:37 +0000 (14:39 +0100)]
imx: base-files: drop redundant space after case keywords

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2 years agokernel: modules: drop 'AddDepends/bluetooth' calls
Piotr Dymacz [Fri, 11 Mar 2022 17:58:36 +0000 (18:58 +0100)]
kernel: modules: drop 'AddDepends/bluetooth' calls

Function 'AddDepends/bluetooth' doesn't exist in our codebase.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2 years agolayerscape: image: drop redundant parameter from kernel build recipe
Piotr Dymacz [Fri, 1 Apr 2022 11:56:36 +0000 (13:56 +0200)]
layerscape: image: drop redundant parameter from kernel build recipe

Neither 'fit', nor target-specific 'traverse-fit' build recipes accept
FDT load address in 3rd parameter.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2 years agokernel: scale nf_conntrack_max more reasonably
Vincent Pelletier [Sat, 19 Feb 2022 02:06:23 +0000 (02:06 +0000)]
kernel: scale nf_conntrack_max more reasonably

Use the kernel's built-in formula for computing this value.
The value applied by OpenWRT's sysctl configuration file does not scale
with the available memory, under-using hardware capabilities.
Also, that formula also influences net.netfilter.nf_conntrack_buckets,
which should improve conntrack performance in average (fewer connections
per hashtable bucket).

Backport upstream commit for its effect on the number of connections per
hashtable bucket.

Apply a hack patch to set the RAM size divisor to a more reasonable value (2048,
down from 16384) for our use case, a typical router handling several thousands
of connections.

Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2 years agoscripts: make sure conffiles are sorted
Paul Spooren [Thu, 31 Mar 2022 21:51:29 +0000 (22:51 +0100)]
scripts: make sure conffiles are sorted

It may happen that conffiles are in different order on different builds.
Make sure they have the same order by sorting them.

FIX: #9612

Signed-off-by: Paul Spooren <mail@aparcar.org>
2 years agotoolchain: reproducible libstdcpp
Paul Spooren [Thu, 31 Mar 2022 16:13:37 +0000 (17:13 +0100)]
toolchain: reproducible libstdcpp

A Python script containing an unreproducible path is copied by default.
Remove it before generating the package.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2 years agoocteon: mark source-only
Stijn Tintel [Fri, 1 Apr 2022 10:05:10 +0000 (13:05 +0300)]
octeon: mark source-only

There is a hard to reproduce, even harder to track down memory leak in
Octeon since kernel 5.10. Mark octeon source-only until it is plugged.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2 years agoRevert "ipq40xx: stop chromium sub-target builds on the buildbots"
Petr Štetiar [Fri, 1 Apr 2022 05:38:43 +0000 (07:38 +0200)]
Revert "ipq40xx: stop chromium sub-target builds on the buildbots"

This reverts commit 35d2bbc29ba7f802706bf65585aeb8808fcac622 as we
believe we found that it is indeed an openssl issue, where openssl is
trying to use getrandom(2), but fails because this particular builder
has an ancient kernel without that syscall. We didn't get to the bottom
of why openssl doesn't fall back to something like /dev/random.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2 years agomxs: enable 5.15 as testing kernel
Zoltan HERPAI [Thu, 31 Mar 2022 13:57:27 +0000 (15:57 +0200)]
mxs: enable 5.15 as testing kernel

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2 years agomxs: update config for 5.15
Zoltan HERPAI [Thu, 31 Mar 2022 13:59:32 +0000 (15:59 +0200)]
mxs: update config for 5.15

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2 years agomxs: copy config from 5.10 to 5.15
Zoltan HERPAI [Thu, 31 Mar 2022 13:56:59 +0000 (15:56 +0200)]
mxs: copy config from 5.10 to 5.15

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2 years agogeneric: add missing symbol for 5.15
Zoltan HERPAI [Thu, 31 Mar 2022 13:56:31 +0000 (15:56 +0200)]
generic: add missing symbol for 5.15

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2 years agobusybox: Fix snprintf arguments in lock
Hauke Mehrtens [Thu, 31 Mar 2022 16:43:09 +0000 (18:43 +0200)]
busybox: Fix snprintf arguments in lock

The first argument for snprintf is the buffer and the 2. one is the
size. Fix the order. This broke the lock application.

Fixes: 34567750db2c ("busybox: fix busybox lock applet pidstr buffer overflow")
Reported-by: Hartmut Birr <e9hack@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2 years agoath79: migrate Archer C5 5GHz radio device paths
Jan-Niklas Burfeind [Mon, 28 Mar 2022 16:07:59 +0000 (18:07 +0200)]
ath79: migrate Archer C5 5GHz radio device paths

When upgrading a TP-Link Archer C5 v1 from ar71xx to ath79,
the 5ghz radio stops working because the device path changed.

Same has been done for the Archer C7 before:

commit e19506f20618 ("ath79: migrate Archer C7 5GHz radio device paths")

Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
2 years agoimx: re-enable ARM arch timer
Petr Štetiar [Thu, 31 Mar 2022 13:50:46 +0000 (15:50 +0200)]
imx: re-enable ARM arch timer

Config option `ARM_ARCH_TIMER` has been removed during rebasing onto
5.15 kernel in commit 2b395c298247 ("imx: update config for 5.15").

Anyway, as stated in commit 8cdc356f8c30 ("mediatek: mt7623: Re-enable
ARM arch timer") config option `ARM_ARCH_TIMER` cannot be enabled in the
config directly; it is only selected by `HAVE_ARM_ARCH_TIMER`. We need
to enable the latter in our config.

Fixes: 2b395c298247 ("imx: update config for 5.15")
Reported-by: Piotr Dymacz <pepe2k@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2 years agokernel: modules: fix kmod-drm-imx-ldb dependency for 5.15
Petr Štetiar [Thu, 31 Mar 2022 13:35:53 +0000 (15:35 +0200)]
kernel: modules: fix kmod-drm-imx-ldb dependency for 5.15

Fixes following issue:

 Package kmod-drm-imx-ldb is missing dependencies for the following libraries:
 drm_dp_aux_bus.ko

Introduced upstream in commit aeb33699fc2c ("drm: Introduce the DP AUX
bus") in kernel version 5.15.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2 years agoimx: make 5.15 default kernel and remove 5.10 support
Petr Štetiar [Thu, 31 Mar 2022 12:42:29 +0000 (14:42 +0200)]
imx: make 5.15 default kernel and remove 5.10 support

In imx target we're sharing single, version agnostic kernel
`config-default` file, which doesn't work very well with current 5.10
and upcoming 5.15 kernel symbols as recent rebase onto 5.15 kernel
introduced in commit 2b395c298247 ("imx: update config for 5.15) has
introduced following regression with 5.10 kernel:

 Marvell 88E6xxx Ethernet switch fabric support (NET_DSA_MV88E6XXX) [Y/n/m/?] y
   Switch Global 2 Registers support (NET_DSA_MV88E6XXX_GLOBAL2) [Y/n/?] (NEW)

That NET_DSA_MV88E6XXX_GLOBAL2 kernel config symbol has been removed in
upstream commit 63368a7416df ("net: dsa: mv88e6xxx: Make global2 support
mandatory") in kernel version 5.12.

This issue could be probably fixed by introduction of separate kernel
config files for each currently used kernel versions and subtarget, but
it is not worth the hassle and resources as imx target is running mostly
upstream kernel, so lets fix it by switching to 5.15 version instead.

Fixes: 2b395c298247 ("imx: update config for 5.15")
Acked-by: Piotr Dymacz <pepe2k@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2 years agotools: SOURCE_DATE_EPOCH handling for mkfs.fat
Paul Spooren [Wed, 30 Mar 2022 22:36:38 +0000 (23:36 +0100)]
tools: SOURCE_DATE_EPOCH handling for mkfs.fat

Backport upstream patch to have reproducible FAT signatures.
This should enable reproducibility for x86 EFI images.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2 years agokernel: modules: fix kmod-drm dependency for 5.15
Petr Štetiar [Tue, 29 Mar 2022 11:33:25 +0000 (13:33 +0200)]
kernel: modules: fix kmod-drm dependency for 5.15

Fixes following issue:

 Package kmod-drm is missing dependencies for the following libraries:
 fb.ko

Introduced upstream in commit f611b1e7624c ("drm: Avoid circular
dependencies for CONFIG_FB") in 5.14.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2 years agokernel: generic: add more missing kernel symbols for 5.15
Petr Štetiar [Tue, 29 Mar 2022 11:04:49 +0000 (13:04 +0200)]
kernel: generic: add more missing kernel symbols for 5.15

Found while adding 5.15 support for imx target.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2 years agoimx: update config for 5.15
Petr Štetiar [Mon, 28 Mar 2022 12:31:55 +0000 (14:31 +0200)]
imx: update config for 5.15

Refresh kernel config with `make kernel_oldconfig` make target.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2 years agoimx: enable 5.15 as testing kernel
Petr Štetiar [Tue, 29 Mar 2022 07:33:31 +0000 (09:33 +0200)]
imx: enable 5.15 as testing kernel

So anyone interested can help with new kernel version integration and
testing.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2 years agoimx: copy config and patches from 5.10 to 5.15
Petr Štetiar [Tue, 29 Mar 2022 07:32:34 +0000 (09:32 +0200)]
imx: copy config and patches from 5.10 to 5.15

So the upcoming changes needed for 5.15 can be reviewed easily.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2 years agobcm53xx: prepare kernel 5.15 support
Rafał Miłecki [Wed, 30 Mar 2022 21:21:32 +0000 (23:21 +0200)]
bcm53xx: prepare kernel 5.15 support

Tested on Luxul XWR-3150 (boot, NAND, PCIe, switch, Ethernet).

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2 years agokernel: bump 5.10 to 5.10.109
John Audia [Mon, 28 Mar 2022 11:54:20 +0000 (07:54 -0400)]
kernel: bump 5.10 to 5.10.109

All patches automatically rebased.

Build system: x86_64
Build-tested: bcm2711/RPi4B, mt7622/RT3200
Run-tested: bcm2711/RPi4B, mt7622/RT3200

Signed-off-by: John Audia <graysky@archlinux.us>
2 years agobusybox: fix busybox lock applet pidstr buffer overflow
Qichao Zhang [Sun, 20 Mar 2022 01:43:22 +0000 (09:43 +0800)]
busybox: fix busybox lock applet pidstr buffer overflow

Kernel setting `/proc/sys/kernel/pid_max` can be set up to 4194304 (7
digits) which will cause buffer overflow in busbox lock patch, this
often happens when running in a rootfs container environment.
This commit enlarges `pidstr` to 12 bytes to ensure a sufficient buffer
for pid number and an additional char '\n'.

Signed-off-by: Qichao Zhang <njuzhangqichao@gmail.com>
2 years agoath79: fix label MAC address for Ubiquiti UniFi AP Outdoor+
Matthias Schiffer [Tue, 29 Mar 2022 22:20:39 +0000 (00:20 +0200)]
ath79: fix label MAC address for Ubiquiti UniFi AP Outdoor+

The label has the MAC address of eth0, not the WLAN PHY address. We can
merge the definition back into ar7241_ubnt_unifi.dtsi, as both DTS
derived from it use the same interface for their label MAC addresses
after all.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2 years agoath79: add 5.15 support for generic subtarget
David Bauer [Sun, 27 Mar 2022 21:12:39 +0000 (23:12 +0200)]
ath79: add 5.15 support for generic subtarget

Add Kernel 5.15 patches + config. This is currently only available for
the generic subtarget, as it was exclusively tested with this target.

Tested-on: Siemens WS-AP3610, Enterasys WS-AP3705i

Signed-off-by: David Bauer <mail@david-bauer.net>
2 years agobcm53xx: add switch ports for Buffalo WZR-900DHP & re-enable it
SHIMAMOTO Takayoshi [Sun, 27 Mar 2022 17:09:25 +0000 (02:09 +0900)]
bcm53xx: add switch ports for Buffalo WZR-900DHP & re-enable it

Specify the switch ports in the DTS file.
Re-enable it after it was disabled by commit e9672b1a8fa4 ("bcm53xx: switch to the
upstream DSA-based b53 driver").

Signed-off-by: SHIMAMOTO Takayoshi <takayoshi.shimamoto.360@gmail.com>
[rmilecki: reword commit & drop unneeded whitespace change]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2 years agobcm53xx: backport DT changes from 5.17 & 5.18
Rafał Miłecki [Wed, 30 Mar 2022 14:05:55 +0000 (16:05 +0200)]
bcm53xx: backport DT changes from 5.17 & 5.18

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2 years agobuild: store sha256_unsigned in JSON
Paul Spooren [Mon, 28 Mar 2022 02:29:09 +0000 (03:29 +0100)]
build: store sha256_unsigned in JSON

Introduce `sha256_unsigned` which is a checksum of the image _before_ a
signature is attached. This is helpful to compare image reproducibility.

Since the `.sha256sum` file is located in the $(KDIR) folder, switch
$(BIN_DIR) with $(KDIR) to simplify the code. The value of $(BIN_DIR)
itself is not stored inside the resulting JSON file, so it can be
replaced.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2 years agomt76: update to the latest version
Felix Fietkau [Tue, 29 Mar 2022 16:34:54 +0000 (18:34 +0200)]
mt76: update to the latest version

eed44048ca57 Revert "mt76: dma: reduce lock contention in mt76_dma_tx_cleanup"

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2 years agobcm53xx: drop dead upgrade code
Rafał Miłecki [Tue, 29 Mar 2022 14:14:54 +0000 (16:14 +0200)]
bcm53xx: drop dead upgrade code

platform_nand_pre_upgrade() is gone since commit 790692dde2b9
("base-files: drop support for the platform_nand_pre_upgrade()").

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2 years agobcm53xx: add support for Asus RT-AC88U
Arınç ÜNAL [Fri, 12 Nov 2021 10:56:15 +0000 (18:56 +0800)]
bcm53xx: add support for Asus RT-AC88U

Asus RT-AC88U is an AC3100 router featuring 9 Ethernet ports over the
integrated Broadcom and the external Realtek switch.

Hardware info:
* Processor: Broadcom BCM4709C0KFEBG dual-core @ 1.4 GHz
* Switch: BCM53012 in BCM4709C0KFEBG & external RTL8365MB
* DDR3 RAM: 512 MB
* Flash: 128 MB (ESMT F59L1G81LA-25T)
* 2.4GHz: BCM4366 4×4 2.4/5G single chip 802.11ac SoC
* 5GHz: BCM4366 4×4 2.4/5G single chip 802.11ac SoC
* Ports: 8 Ports, 1 WAN Ports

Flashing instructions:
* Boot to CFE Recovery Mode by holding the reset button while power-on.
* Connect to the router with an ethernet cable.
* Set IPv4 address of the computer to 192.168.1.2 subnet 255.255.255.0.
* Head to http://192.168.1.1.
* Reset NVRAM.
* Upload the OpenWrt image.

CFE bootloader may reject flashing the image due to image integrity check.
In that case, follow the instructions below.

* Rename the OpenWrt image as firmware.trx.
* Run a TFTP server and make it serve the firmware.trx file.
* Run the URL below on a browser or curl.
  http://192.168.1.1/do.htm?cmd=flash+-noheader+192.168.1.2:firmware.trx+flash0.trx

Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
[rmilecki: mark BROKEN until we sort out nvram & CFE recovery]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2 years agokernel: fix initramfs reproducibility
Daniel Golle [Tue, 29 Mar 2022 12:54:14 +0000 (13:54 +0100)]
kernel: fix initramfs reproducibility

Make sure xz uses at least 2 threads so compression always runs in
multi-threaded mode as the resulting file in single-threaded mode
differs.

Fixes: 29d7461d11 ("kernel: set options to make external initramfs reproducible")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2 years agoimage: let mksquashfs4 use all processors
Stijn Tintel [Sat, 19 Feb 2022 15:54:22 +0000 (17:54 +0200)]
image: let mksquashfs4 use all processors

Drop the -processors argument from the mksquashfs4 call, so it will use
all available processors. This dramatically reduces the time to create
squashfs filesystems.

The times below are observed when building an image for my main router,
the WatchGuard Firebox M300 (qoriq target):

Before:
real    4m45,973s

After:
real    0m23,497s

With this commit `mksquashfs` may use more cores than defined via `-j`.
This is the same behaviour as for archive creation of ImageBuilder, SDK
or toolchain. There is no trivial way to limit `mksquashfs` CPU core
usage to the amount of "free" make jobs since two running `mksquashfs`
instances would each run with the total allowed number (-j) of threads.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
[extended reasoning in commit message]
Signed-off-by: Paul Spooren <mail@aparcar.org>
2 years agorealtek: Fix tc default package
Hauke Mehrtens [Mon, 28 Feb 2022 21:32:08 +0000 (22:32 +0100)]
realtek: Fix tc default package

The tc package does not exits any more, it was split into tc-tiny,
tc-full and tc-bpf. Include tc-bpf by default into realtek images.

This increases the compressed image size by about 232KBytes.

Tested-by: Stijn Segers <foss@volatilesystems.org>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2 years agorealtek: Use firewall4
Hauke Mehrtens [Mon, 28 Feb 2022 20:57:55 +0000 (21:57 +0100)]
realtek: Use firewall4

The realtek target is not a router, but basic device, see DEVICE_TYPE.
The basic device type does not come with firewall by default, see
include/target.mk for details. The realtek target extended
DEFAULT_PACKAGES manually with firewall.

This changes the defaults to take firewall4 and nftables instead of
firewall and iptables. This also adds the additional package
kmod-nft-offload.

The only difference to the router type is the missing ppp,
ppp-mod-pppoe, dnsmasq and odhcpd-ipv6only package.

This increases the compressed image size by about 422KBytes.

Tested-by: Stijn Segers <foss@volatilesystems.org>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2 years agorealtek: Remove dnsmasq and odhcpd-ipv6only from default
Hauke Mehrtens [Fri, 25 Mar 2022 12:57:40 +0000 (13:57 +0100)]
realtek: Remove dnsmasq and odhcpd-ipv6only from default

Do not include the dnsmasq and odhcpd-ipv6only package by default any
more. These services are not needed on a switch. If someone needs this
it is still possible to use opkg or image builder to add them.

This decreases the compressed image size by about 165KBytes.

Tested-by: Stijn Segers <foss@volatilesystems.org>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>