openwrt/staging/blogic.git
5 years agoASoC: SOF: Intel: initialise and verify FW crash dump data.
Liam Girdwood [Fri, 27 Sep 2019 20:05:36 +0000 (15:05 -0500)]
ASoC: SOF: Intel: initialise and verify FW crash dump data.

FW mailbox offset was not set before use and HDR size was not validated.
Fix this.

Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190927200538.660-12-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: SOF: Intel: hda: fix warnings during FW load
Kai Vehmanen [Fri, 27 Sep 2019 20:05:35 +0000 (15:05 -0500)]
ASoC: SOF: Intel: hda: fix warnings during FW load

The "snd_pcm_substream" handle was not initialized properly
in hda-loader.c for firmware load.

When the HDA DMAs were used to load the firmware,
the interrupts related to firmware load also triggered
calls to snd_sof_pcm_period_elapsed() on a non-existent ALSA
PCM stream.

This caused runtime kernel warnings from
pcm_lib.c:snd_pcm_period_elapsed().

Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190927200538.660-11-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: SOF: pcm: harden PCM STOP sequence
Pan Xiuli [Fri, 27 Sep 2019 20:05:31 +0000 (15:05 -0500)]
ASoC: SOF: pcm: harden PCM STOP sequence

The old STOP sequence is: 1. stop DMA 2. send STOP ipc
If delay happen before the steps 1 and 2, the DMA buffer will be empty in
short time and cause pipeline xrun then stop the pipeline.
Then the step 2 ipc stop will return error as pipeline is already stopped.

Suggested change to avoid the issue is to switch the order of steps 1 and 2
for the stop sequence.

Signed-off-by: Pan Xiuli <xiuli.pan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190927200538.660-7-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: SOF: pcm: fix resource leak in hw_free
Kai Vehmanen [Fri, 27 Sep 2019 20:05:30 +0000 (15:05 -0500)]
ASoC: SOF: pcm: fix resource leak in hw_free

Fix a bug in sof_pcm_hw_free() where some cleanup actions were
skipped if STREAM_PCM_FREE IPC was already successfully sent to
DSP when the stream was stopped or suspended. This is incorrect
as hw_free should clean up also other resources, including pcm
lib page allocations, period elapsed work queue and call to
platform hw_free.

Fixes: c29d96c3b9b4 ("ASoC: SOF: reset DMA state in prepare")
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190927200538.660-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: SOF: topology: fix parse fail issue for byte/bool tuple types
Keyon Jie [Fri, 27 Sep 2019 20:05:27 +0000 (15:05 -0500)]
ASoC: SOF: topology: fix parse fail issue for byte/bool tuple types

We are using sof_parse_word_tokens() to parse tokens with
bool/byte/short/word tuple types, here add the missing check, to fix the
parsing failure at byte/bool tuple types.

Signed-off-by: Keyon Jie <yang.jie@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190927200538.660-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: SOF: loader: fix kernel oops on firmware boot failure
Pierre-Louis Bossart [Fri, 27 Sep 2019 20:05:26 +0000 (15:05 -0500)]
ASoC: SOF: loader: fix kernel oops on firmware boot failure

When we fail to boot the firmware, we encounter a kernel oops in
hda_dsp_get_registers(), which is called conditionally in
hda_dsp_dump() when the sdev_>boot_complete flag is set.

Setting this flag _after_ dumping the data fixes the issue and does
not change the programming flow.

Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190927200538.660-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: wm_adsp: Fix theoretical NULL pointer for alg_region
Li Xu [Tue, 1 Oct 2019 13:09:11 +0000 (14:09 +0100)]
ASoC: wm_adsp: Fix theoretical NULL pointer for alg_region

Fix potential NULL pointer dereference for alg_region in
wm_adsp_buffer_parse_legacy. In practice this can never happen as
loading the firmware should have failed at the wm_adsp2_setup_algs
stage, however probably better for the code to be robust against
future changes and this is more helpful for static analysis.

Signed-off-by: Li Xu <li.xu@cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20191001130911.19238-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: max98373: check for device node before parsing
Sathyanarayana Nujella [Sat, 28 Sep 2019 20:22:30 +0000 (13:22 -0700)]
ASoC: max98373: check for device node before parsing

Below Oops is caused in a system which uses ACPI instead of device node:

of_get_named_gpiod_flags: can't parse 'maxim,reset-gpio' property of node '(null)[0]'
BUG: kernel NULL pointer dereference, address: 0000000000000010

This patch avoids NULL pointer deferencing by adding a check before parsing
and initializes to make reset-gpio pin as invalid.

Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Signed-off-by: Jairaj Arava <jairaj.arava@intel.com>
Link: https://lore.kernel.org/r/1569702150-11976-1-git-send-email-sathyanarayana.nujella@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: topology: Fix a signedness bug in soc_tplg_dapm_widget_create()
Dan Carpenter [Wed, 25 Sep 2019 11:06:24 +0000 (14:06 +0300)]
ASoC: topology: Fix a signedness bug in soc_tplg_dapm_widget_create()

The "template.id" variable is an enum and in this context GCC will
treat it as an unsigned int so it can never be less than zero.

Fixes: 8a9782346dcc ("ASoC: topology: Add topology core")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20190925110624.GR3264@mwanda
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: soc-component: fix a couple missing error assignments
Dan Carpenter [Mon, 23 Sep 2019 14:22:57 +0000 (17:22 +0300)]
ASoC: soc-component: fix a couple missing error assignments

There were a couple places where the return value wasn't assigned so the
error handling wouldn't trigger.

Fixes: 5c0769af4caf ("ASoC: soc-dai: add snd_soc_dai_bespoke_trigger()")
Fixes: 95aef3553384 ("ASoC: soc-dai: add snd_soc_dai_trigger()")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20190923142257.GB31251@mwanda
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: wm8994: Do not register inapplicable controls for WM1811
Sylwester Nawrocki [Fri, 20 Sep 2019 13:02:10 +0000 (15:02 +0200)]
ASoC: wm8994: Do not register inapplicable controls for WM1811

In case of WM1811 device there are currently being registered controls
referring to registers not existing on that device.
It has been noticed when getting values of "AIF1ADC2 Volume", "AIF1DAC2
Volume" controls was failing during ALSA state restoring at boot time:
 "amixer: Mixer hw:0 load error: Device or resource busy"

Reading some registers through I2C was failing with EBUSY error and
indeed these registers were not available according to the datasheet.

To fix this controls not available on WM1811 are moved to a separate
array and registered only for WM8994 and WM8958.

There are some further differences between WM8994 and WM1811,
e.g. registers 603h, 604h, 605h, which are not covered in this patch.

Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Link: https://lore.kernel.org/r/20190920130218.32690-2-s.nawrocki@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: samsung: arndale: Add missing OF node dereferencing
Sylwester Nawrocki [Fri, 20 Sep 2019 13:02:11 +0000 (15:02 +0200)]
ASoC: samsung: arndale: Add missing OF node dereferencing

Ensure there is no OF node references kept when the driver
is removed/unbound.

Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20190920130218.32690-3-s.nawrocki@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: ti: fix SND_SOC_DM365_VOICE_CODEC dependencies
Arnd Bergmann [Fri, 20 Sep 2019 07:50:18 +0000 (09:50 +0200)]
ASoC: ti: fix SND_SOC_DM365_VOICE_CODEC dependencies

SND_SOC_DM365_VOICE_CODEC is a 'bool' option in a choice statement,
meaning it cannot be set to =m, but it selects two other drivers
that we may want to be loadable modules after all:

WARNING: unmet direct dependencies detected for SND_SOC_CQ0093VC
  Depends on [m]: SOUND [=m] && !UML && SND [=m] && SND_SOC [=m]
  Selected by [y]:
  - SND_SOC_DM365_VOICE_CODEC [=y] && <choice>
  Selected by [m]:
  - SND_SOC_ALL_CODECS [=m] && SOUND [=m] && !UML && SND [=m] && SND_SOC [=m] && COMPILE_TEST [=y]

Add an intermediate symbol that sets SND_SOC_CQ0093VC and
MFD_DAVINCI_VOICECODEC to =m if SND_SOC=m.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20190920075046.3210393-1-arnd@arndb.de
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: pcm3168a: The codec does not support S32_LE
Peter Ujfalusi [Thu, 19 Sep 2019 07:16:52 +0000 (10:16 +0300)]
ASoC: pcm3168a: The codec does not support S32_LE

24 bits is supported in all modes and 16 bit only when the codec is slave
and the DAI is set to RIGHT_J.

Remove the unsupported sample format.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20190919071652.31724-1-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: core: use list_del_init and move it back to soc_cleanup_component
Bard liao [Wed, 18 Sep 2019 13:31:31 +0000 (21:31 +0800)]
ASoC: core: use list_del_init and move it back to soc_cleanup_component

commit a0a4bf57a977 ("ASoC: core: delete component->card_list in soc_remove_component only")
was trying to fix a kernel oops when list_del was called twice without
re-init the list. Use list_del_init() can solve it, too. Besides, it
will be more readable if we cleanup all component related resource at
soc_cleanup_component().

Suggested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Bard liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20190918133131.15045-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: rsnd: do error check after rsnd_channel_normalization()
Kuninori Morimoto [Wed, 18 Sep 2019 06:02:38 +0000 (15:02 +0900)]
ASoC: rsnd: do error check after rsnd_channel_normalization()

SSI need to use rsnd_channel_normalization() for TDM-split mode,
thus, channel check need to do after that.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/874l1aw39d.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: atmel_ssc_dai: Remove wrong spinlock usage
Gregory CLEMENT [Wed, 18 Sep 2019 10:03:44 +0000 (12:03 +0200)]
ASoC: atmel_ssc_dai: Remove wrong spinlock usage

A potential bug was reported in the email "[BUG] atmel_ssc_dai: a
possible sleep-in-atomic bug in atmel_ssc_shutdown"[1]

Indeed in the function atmel_ssc_shutdown() free_irq() was called in a
critical section protected by spinlock.

However this spinlock is only used in atmel_ssc_shutdown() and
atmel_ssc_startup() functions. After further analysis, it occurred that
the call to these function are already protected by mutex used on the
calling functions.

Then we can remove the spinlock which will fix this bug as a side
effect. Thanks to this patch the following message disappears:

"BUG: sleeping function called from invalid context at
kernel/locking/mutex.c:909"

[1]: https://www.spinics.net/lists/alsa-devel/msg71286.html

Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20190918100344.23629-1-gregory.clement@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: core: delete component->card_list in soc_remove_component only
Bard Liao [Mon, 16 Sep 2019 21:03:53 +0000 (05:03 +0800)]
ASoC: core: delete component->card_list in soc_remove_component only

We add component->card_list in the end of soc_probe_component(). In
other words, component->card_list will not be added if there is an
error in the soc_probe_component() function. So we can't delete
component->card_list in the error handling of soc_probe_component().

Fixes: 22d1423187e5 ("ASoC: soc-core: add soc_cleanup_component()")
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190916210353.6318-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: fsl_sai: Fix noise when using EDMA
Mihai Serban [Fri, 13 Sep 2019 19:28:05 +0000 (22:28 +0300)]
ASoC: fsl_sai: Fix noise when using EDMA

EDMA requires the period size to be multiple of maxburst. Otherwise the
remaining bytes are not transferred and thus noise is produced.

We can handle this issue by adding a constraint on
SNDRV_PCM_HW_PARAM_PERIOD_SIZE to be multiple of tx/rx maxburst value.

Signed-off-by: Mihai Serban <mihai.serban@nxp.com>
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Link: https://lore.kernel.org/r/20190913192807.8423-2-daniel.baluta@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: sdm845: remove unneeded semicolon
Saiyam Doshi [Sat, 14 Sep 2019 03:11:33 +0000 (08:41 +0530)]
ASoC: sdm845: remove unneeded semicolon

Remove excess semicolon after closing parenthesis.

Signed-off-by: Saiyam Doshi <saiyamdoshi.in@gmail.com>
Link: https://lore.kernel.org/r/20190914031133.GA28447@SD
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: fsl_sai: Implement set_bclk_ratio
Viorel Suman [Fri, 30 Aug 2019 21:59:10 +0000 (00:59 +0300)]
ASoC: fsl_sai: Implement set_bclk_ratio

This is to allow machine drivers to set a certain bitclk rate
which might not be exactly rate * frame size.

Cc: NXP Linux Team <linux-imx@nxp.com>
Signed-off-by: Viorel Suman <viorel.suman@nxp.com>
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Link: https://lore.kernel.org/r/20190830215910.31590-1-daniel.baluta@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: wcd9335: remove redundant use of ret variable
Saiyam Doshi [Mon, 9 Sep 2019 17:45:41 +0000 (23:15 +0530)]
ASoC: wcd9335: remove redundant use of ret variable

All these functions declares and initializes variable ret with
'0' and without modifying 'ret' variable, it is returned.

This patch removes this redundancy and returns '0' directly.

Signed-off-by: Saiyam Doshi <saiyamdoshi.in@gmail.com>
Link: https://lore.kernel.org/r/20190909174541.GA22718@SD
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: hdmi-codec: Add an op to set callback function for plug event
Cheng-Yi Chiang [Wed, 17 Jul 2019 08:33:23 +0000 (16:33 +0800)]
ASoC: hdmi-codec: Add an op to set callback function for plug event

Add an op in hdmi_codec_ops so codec driver can register callback
function to handle plug event.

Driver in DRM can use this callback function to report connector status.

Signed-off-by: Cheng-Yi Chiang <cychiang@chromium.org>
Link: https://lore.kernel.org/r/20190717083327.47646-2-cychiang@chromium.org
Reviewed-by: Tzung-Bi Shih <tzungbi@google.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: rt5677: keep analog power register at SND_SOC_BIAS_OFF
Ben Zhang [Fri, 6 Sep 2019 19:46:24 +0000 (12:46 -0700)]
ASoC: rt5677: keep analog power register at SND_SOC_BIAS_OFF

Instead of clearing RT5677_PWR_ANLG2 (MX-64h) to 0 at SND_SOC_BIAS_OFF,
we only clear the RT5677_PWR_CORE bit which is set at SND_SOC_BIAS_PREPARE.
MICBIAS control bits are left unchanged.

This fixed the bug where if MICBIAS1 widget is forced on, MICBIAS
control bits will be cleared at suspend and never turned back on again,
since DAPM thinks the widget is always on.

Signed-off-by: Ben Zhang <benzh@chromium.org>
Signed-off-by: Curtis Malainey <cujomalainey@chromium.org>
Link: https://lore.kernel.org/r/20190906194636.217881-3-cujomalainey@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: rt5677: Remove magic number register writes
Curtis Malainey [Fri, 6 Sep 2019 19:46:23 +0000 (12:46 -0700)]
ASoC: rt5677: Remove magic number register writes

In order to simplify understanding what register values are being
written to the codec for debugging more advanced features (such as
hotwording) it is best to remove magic numbers

Signed-off-by: Curtis Malainey <cujomalainey@chromium.org>
Link: https://lore.kernel.org/r/20190906194636.217881-2-cujomalainey@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: soc-core: self contained soc_unbind_aux_dev()
Kuninori Morimoto [Wed, 4 Sep 2019 00:15:40 +0000 (09:15 +0900)]
ASoC: soc-core: self contained soc_unbind_aux_dev()

Current soc_unbind_aux_dev() implementation is very half,
thus it is very unreadable.

for_each_comp_order(order) {
for_each_card_auxs_safe(card, comp, _comp) {

(1) if (comp->driver->remove_order == order) {
...
=> soc_unbind_aux_dev(comp);
}
}

soc_unbind_aux_dev() itself is not related to remove_order (1).
And, it is called from soc_remove_aux_devices(), even though
its paired function soc_bind_aux_dev() is called from
snd_soc_instantiate_card().
It is very unbalance, and very difficult to understand.

This patch do
1) update soc_bind_aux_dev() to self contained
2) call it from soc_cleanup_card_resources() to make up balance

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87r24wor0z.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: soc-core: add soc_unbind_aux_dev()
Kuninori Morimoto [Wed, 4 Sep 2019 00:15:35 +0000 (09:15 +0900)]
ASoC: soc-core: add soc_unbind_aux_dev()

It is easy to read code if it is cleanly using paired function/naming,
like start <-> stop, register <-> unregister, etc, etc.
But, current ALSA SoC code is very random, unbalance, not paired, etc.
It is easy to create bug at the such code, and it will be difficult to
debug.

soc-core.c has soc_bind_aux_dev(), but, there is no its paired
soc_unbind_aux_dev().
This patch adds soc_unbind_aux_dev().

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87sgpcor14.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: soc-core: self contained soc_bind_aux_dev()
Kuninori Morimoto [Wed, 4 Sep 2019 00:15:28 +0000 (09:15 +0900)]
ASoC: soc-core: self contained soc_bind_aux_dev()

Current soc_bind_aux_dev() implementation is very half,
thus it is very unreadable.

for_each_card_pre_auxs(xxx) {
=> ret = soc_bind_aux_dev(xxx);
...
}

This patch does all for_each_xxx() under soc_bind_aux_dev(),
and makes it to self contained.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87tv9sor1b.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: soc-core: move soc_probe_link_dais() next to soc_remove_link_dais()
Kuninori Morimoto [Wed, 4 Sep 2019 00:15:23 +0000 (09:15 +0900)]
ASoC: soc-core: move soc_probe_link_dais() next to soc_remove_link_dais()

It is easy to read code if it is cleanly using paired function/naming,
like start <-> stop, register <-> unregister, etc, etc.
But, current ALSA SoC code is very random, unbalance, not paired, etc.
It is easy to create bug at the such code, and it will be difficult to
debug.

This patch moves soc_probe_link_dais() next to soc_remove_link_dais()
which is paired function.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87v9u8or1g.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: soc-core: self contained soc_probe_link_dais()
Kuninori Morimoto [Wed, 4 Sep 2019 00:15:17 +0000 (09:15 +0900)]
ASoC: soc-core: self contained soc_probe_link_dais()

Current soc_probe_link_dais() implementation is very half,
thus it is very difficult to read.

for_each_comp_order(xxx) {
for_each_card_rtds(xxx)
=> soc_probe_link_dais(xxx);
}

This patch does all for_each_xxx() under soc_probe_link_dais(),
and makes it to self contained.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87woeoor1m.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: soc-core: add new soc_link_init()
Kuninori Morimoto [Wed, 4 Sep 2019 00:15:12 +0000 (09:15 +0900)]
ASoC: soc-core: add new soc_link_init()

Current soc_probe_link_dais() (1) is called under probe_order (2),
and it will initialize dai_link related settings at *Last* turn (3)(B).
It is very complex code.

static int soc_probe_link_dais(..., order)
{
(A) /* probe DAIs here */
...

(3) if (order != SND_SOC_COMP_ORDER_LAST)
return 0;

(B) /* initialize dai_link related settings */
...
}

static int snd_soc_instantiate_card(...)
{
...
(2) for_each_comp_order(order) {
for_each_card_rtds(...) {
(1) ret = soc_probe_link_dais(..., order);
}
}
}

This patch separes soc_probe_link_dais() into "DAI probe" portion (A),
and dai_link settings portion (B).
The later is named as soc_link_init() by this patch.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87y2z4or1r.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: soc-core: move soc_probe_dai() next to soc_remove_dai()
Kuninori Morimoto [Wed, 4 Sep 2019 00:15:06 +0000 (09:15 +0900)]
ASoC: soc-core: move soc_probe_dai() next to soc_remove_dai()

It is easy to read code if it is cleanly using paired function/naming,
like start <-> stop, register <-> unregister, etc, etc.
But, current ALSA SoC code is very random, unbalance, not paired, etc.
It is easy to create bug at the such code, and it will be difficult to
debug.

This patch moves soc_probe_dai() next to soc_remove_dai() which is
paired function.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87zhjkor1x.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: soc-core: self contained soc_remove_link_dais()
Kuninori Morimoto [Wed, 4 Sep 2019 00:14:57 +0000 (09:14 +0900)]
ASoC: soc-core: self contained soc_remove_link_dais()

Current soc_remove_link_dais() implementation is very half,
thus it is very difficult to read.

for_each_comp_order(xxx) {
for_each_card_rtds(xxx)
=> soc_remove_link_dais(xxx);
}

This patch does all for_each_xxx() under soc_remove_link_dais(),
and makes it to self contained.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/871rwwq5mm.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: soc-core: self contained soc_remove_link_components()
Kuninori Morimoto [Wed, 4 Sep 2019 00:14:51 +0000 (09:14 +0900)]
ASoC: soc-core: self contained soc_remove_link_components()

Current soc_remove_link_components() implementation is very half,
thus it is very difficult to read.

for_each_comp_order(xxx) {
for_each_card_rtds(xxx)
=> soc_remove_link_components(xxx);
}

This patch does all for_each_xxx() under soc_remove_link_components(),
and makes it to self contained.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/8736hcq5ms.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: soc-core: self contained soc_probe_link_components()
Kuninori Morimoto [Wed, 4 Sep 2019 00:14:46 +0000 (09:14 +0900)]
ASoC: soc-core: self contained soc_probe_link_components()

Current soc_probe_link_components() implementation is very half,
thus it is very difficult to read.

for_each_comp_order(xxx) {
for_each_card_rtds(xxx) {
=> ret = soc_probe_link_components(xxx);
...
}
}

This patch does all for_each_xxx() under soc_probe_link_components(),
and makes it to self contained.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/874l1sq5mx.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: rt1308: make array pd static const, makes object smaller
Colin Ian King [Sat, 7 Sep 2019 07:46:34 +0000 (08:46 +0100)]
ASoC: rt1308: make array pd static const, makes object smaller

Don't populate the array pd on the stack but instead make it
static const. Makes the object code smaller by 82 bytes.

Before:
   text    data     bss     dec     hex filename
  26548    7288      64   33900    846c sound/soc/codecs/rt1308.o

After:
   text    data     bss     dec     hex filename
  26370    7384      64   33818    841a sound/soc/codecs/rt1308.o

(gcc version 9.2.1, amd64)

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20190907074634.22144-1-colin.king@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: rt1305: make array pd static const, makes object smaller
Colin Ian King [Sat, 7 Sep 2019 07:41:56 +0000 (08:41 +0100)]
ASoC: rt1305: make array pd static const, makes object smaller

Don't populate the array pd on the stack but instead make it
static const. Makes the object code smaller by 93 bytes.

Before:
   text    data     bss     dec     hex filename
  38961    9784      64   48809    bea9 sound/soc/codecs/rt1305.o

After:
   text    data     bss     dec     hex filename
  38804    9848      64   48716    be4c sound/soc/codecs/rt1305.o

(gcc version 9.2.1, amd64)

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20190907074156.21907-1-colin.king@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: rt1011: make array pd static const, makes object smaller
Colin Ian King [Sat, 7 Sep 2019 07:37:17 +0000 (08:37 +0100)]
ASoC: rt1011: make array pd static const, makes object smaller

Don't populate the array pd on the stack but instead make it
static const. Makes the object code smaller by 100 bytes.

Before:
   text    data     bss     dec     hex filename
  51463   13016     128   64607    fc5f sound/soc/codecs/rt1011.o

After:
   text    data     bss     dec     hex filename
  51299   13080     128   64507    fbfb sound/soc/codecs/rt1011.o

(gcc version 9.2.1, amd64)

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20190907073717.21632-1-colin.king@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoSoC: simple-card-utils: set 0Hz to sysclk when shutdown
Katsuhiro Suzuki [Sat, 7 Sep 2019 17:45:01 +0000 (02:45 +0900)]
SoC: simple-card-utils: set 0Hz to sysclk when shutdown

This patch set 0Hz to sysclk when shutdown the card.

Some codecs set rate constraints that derives from sysclk. This
mechanism works correctly if machine drivers give fixed frequency.

But simple-audio and audio-graph card set variable clock rate if
'mclk-fs' property exists. In this case, rate constraints will go
bad scenario. For example a codec accepts three limited rates
(mclk / 256, mclk / 384, mclk / 512).

Bad scenario as follows (mclk-fs = 256):
   - Initialize sysclk by correct value (Ex. 12.288MHz)
     - Codec set constraints of PCM rate by sysclk
       48kHz (1/256), 32kHz (1/384), 24kHz (1/512)
   - Play 48kHz sound, it's acceptable
   - Sysclk is not changed

   - Play 32kHz sound, it's acceptable
   - Set sysclk to 8.192MHz (= fs * mclk-fs = 32k * 256)
     - Codec set constraints of PCM rate by sysclk
       32kHz (1/256), 21.33kHz (1/384), 16kHz (1/512)

   - Play 48kHz again, but it's NOT acceptable because constraints
     do not allow 48kHz

So codecs treat 0Hz sysclk as signal of applying no constraints to
avoid this problem.

Signed-off-by: Katsuhiro Suzuki <katsuhiro@katsuster.net>
Link: https://lore.kernel.org/r/20190907174501.19833-1-katsuhiro@katsuster.net
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: rockchip: ignore 0Hz sysclk
Katsuhiro Suzuki [Sat, 7 Sep 2019 17:43:32 +0000 (02:43 +0900)]
ASoC: rockchip: ignore 0Hz sysclk

This patch ignores sysclk setting if it is 0Hz.

Some codecs treat 0Hz sysclk as signal of applying no constraints.
This driver does not have such feature but current implementation
outputs 'Failed to set mclk' error message if machine driver sets
0Hz sysclk to this driver.

Signed-off-by: Katsuhiro Suzuki <katsuhiro@katsuster.net>
Link: https://lore.kernel.org/r/20190907174332.19586-1-katsuhiro@katsuster.net
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: codecs: ad193x: make two arrays static const, makes object smaller
Colin Ian King [Fri, 6 Sep 2019 16:14:04 +0000 (17:14 +0100)]
ASoC: codecs: ad193x: make two arrays static const, makes object smaller

Don't populate the arrays on the stack but instead make them
static const. Makes the object code smaller by 37 bytes.

Before:
   text    data     bss     dec     hex filename
  16253    7200       0   23453    5b9d sound/soc/codecs/ad193x.o

After:
   text    data     bss     dec     hex filename
  16056    7360       0   23416    5b78 sound/soc/codecs/ad193x.o

(gcc version 9.2.1, amd64)

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20190906161404.1440-1-colin.king@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: es8316: support fixed and variable both clock rates
Katsuhiro Suzuki [Sat, 7 Sep 2019 16:36:53 +0000 (01:36 +0900)]
ASoC: es8316: support fixed and variable both clock rates

This patch supports some type of machine drivers that set 0 to mclk
when sound device goes to idle state. After applied this patch,
sysclk == 0 means there is no constraint of sound rate and other
values will set constraints which is derived by sysclk setting.

Original code refuses sysclk == 0 setting. But some boards and SoC
(such as RockPro64 and RockChip I2S) has connected SoC MCLK out to
ES8316 MCLK in. In this case, SoC side I2S will choose suitable
frequency of MCLK such as fs * mclk-fs when user starts playing or
capturing.

Bad scenario as follows (mclk-fs = 256):
  - Initialize sysclk by correct value (Ex. 12.288MHz)
    - ES8316 set constraints of PCM rate by sysclk
      48kHz (1/256), 32kHz (1/384), 30.720kHz (1/400),
      24kHz (1/512), 16kHz (1/768), 12kHz (1/1024)
  - Play 48kHz sound, it's acceptable
  - Sysclk is not changed

  - Play 32kHz sound, it's acceptable
  - Set sysclk by 8.192MHz (= fs * mclk-fs = 32k * 256)
    - ES8316 set constraints of PCM rate by sysclk
      32kHz (1/256), 21.33kHz (1/384), 20.48kHz (1/400),
      16kHz (1/512), 10.66kHz (1/768), 8kHz (1/1024)

  - Play 48kHz again, but it's NOT acceptable because constraints
    list does not allow 48kHz

Signed-off-by: Katsuhiro Suzuki <katsuhiro@katsuster.net>
Link: https://lore.kernel.org/r/20190907163653.9382-2-katsuhiro@katsuster.net
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: es8316: fix redundant codes of clock
Katsuhiro Suzuki [Sat, 7 Sep 2019 16:36:52 +0000 (01:36 +0900)]
ASoC: es8316: fix redundant codes of clock

This patch removes redundant null checks for optional MCLK clock.
And fix DT binding document for changing clock property to optional
from required.

Signed-off-by: Katsuhiro Suzuki <katsuhiro@katsuster.net>
Link: https://lore.kernel.org/r/20190907163653.9382-1-katsuhiro@katsuster.net
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: SOF: imx8: Fix COMPILE_TEST error
YueHaibing [Thu, 5 Sep 2019 06:44:00 +0000 (14:44 +0800)]
ASoC: SOF: imx8: Fix COMPILE_TEST error

When do compile test, if SND_SOC_SOF_OF is not set, we get:

sound/soc/sof/imx/imx8.o: In function `imx8_dsp_handle_request':
imx8.c:(.text+0xb0): undefined reference to `snd_sof_ipc_msgs_rx'
sound/soc/sof/imx/imx8.o: In function `imx8_ipc_msg_data':
imx8.c:(.text+0xf4): undefined reference to `sof_mailbox_read'
sound/soc/sof/imx/imx8.o: In function `imx8_dsp_handle_reply':
imx8.c:(.text+0x160): undefined reference to `sof_mailbox_read'

Make SND_SOC_SOF_IMX_TOPLEVEL always depends on SND_SOC_SOF_OF

Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 202acc565a1f ("ASoC: SOF: imx: Add i.MX8 HW support")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190905064400.24800-1-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: meson: tdmout: add sm1 support
Jerome Brunet [Thu, 5 Sep 2019 12:01:20 +0000 (14:01 +0200)]
ASoC: meson: tdmout: add sm1 support

On the sm1, the TDMOUT number of input is extended and the
the gain enable bit moved to accommodate this extension

Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20190905120120.31752-9-jbrunet@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: meson: axg-toddr: add sm1 support
Jerome Brunet [Thu, 5 Sep 2019 12:01:19 +0000 (14:01 +0200)]
ASoC: meson: axg-toddr: add sm1 support

On sm1, the maximum number TODDR inputs is extended to 16.

Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20190905120120.31752-8-jbrunet@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: meson: axg-frddr: add sm1 support
Jerome Brunet [Thu, 5 Sep 2019 12:01:18 +0000 (14:01 +0200)]
ASoC: meson: axg-frddr: add sm1 support

On sm1, the output routing bits have moved to CTRL2 register

Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20190905120120.31752-7-jbrunet@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: meson: tdmin: expose all 16 inputs
Jerome Brunet [Thu, 5 Sep 2019 12:01:17 +0000 (14:01 +0200)]
ASoC: meson: tdmin: expose all 16 inputs

The TDMIN component, as it, has a maximum of 16 input. Depending on
the SoC, these may not all be connected.

Instead of decribing only the connected inputs of each SoC, describe
them all and let ASoC routing do the rest.

Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20190905120120.31752-6-jbrunet@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: meson: axg-toddr: expose all 8 inputs
Jerome Brunet [Thu, 5 Sep 2019 12:01:16 +0000 (14:01 +0200)]
ASoC: meson: axg-toddr: expose all 8 inputs

The TODDR component, as it, has a maximum of 8 input. Depending on
the SoC, these may not all be connected or some input components may
not be supported

Instead of decribing only the connected inputs, describe them all
and let ASoC routing do the rest.

Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20190905120120.31752-5-jbrunet@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: meson: axg-frddr: expose all 8 outputs
Jerome Brunet [Thu, 5 Sep 2019 12:01:15 +0000 (14:01 +0200)]
ASoC: meson: axg-frddr: expose all 8 outputs

The FRDDR component, as it, has a maximum of 8 outputs. Depending on
the SoC, these may not all be connected.

Instead of decribing only the connected outputs of each SoC, describe
them all and let ASoC routing do the rest.

Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20190905120120.31752-4-jbrunet@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: meson: add reset binding
Jerome Brunet [Thu, 5 Sep 2019 12:01:14 +0000 (14:01 +0200)]
ASoC: meson: add reset binding

The g12a audio subsystem, which is a derivative of the axg subsystem,
provides a dedicated reset line for each of the audio components.

The axg did not provide that and it is unclear if/when these reset are
required. The reset already helped solve a channel mapping issue on the
tdm formatter devices. Let's add the reset binding for the other
components, so we can describe this in DT. We'll use it later on
in the driver when/if needed.

Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20190905120120.31752-3-jbrunet@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: meson: add sm1 compatibles
Jerome Brunet [Thu, 5 Sep 2019 12:01:13 +0000 (14:01 +0200)]
ASoC: meson: add sm1 compatibles

Document the compatible strings of the audio devices of the sm1 SoC
family

Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20190905120120.31752-2-jbrunet@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: qcom: common: Include link-name in error messages
Bjorn Andersson [Thu, 5 Sep 2019 04:03:06 +0000 (21:03 -0700)]
ASoC: qcom: common: Include link-name in error messages

Reading out the link-name earlier and including it in the various error
messages makes it much more convenient to figure out what links have
unmet dependencies.

Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20190905040306.21399-1-bjorn.andersson@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: soc-core: add comment to jack at soc_remove_component()
Kuninori Morimoto [Wed, 4 Sep 2019 00:14:35 +0000 (09:14 +0900)]
ASoC: soc-core: add comment to jack at soc_remove_component()

Basically, driver which setups snd_soc_component_set_jack() need
to release it by themselves. But, as framework level robustness,
soc_remove_component() also releases it.

To avoid code reader confuse, this patch makes it clarify.

This patch makes it clarify.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/875zm8q5n8.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: tegra: use devm_platform_ioremap_resource() to simplify code
YueHaibing [Wed, 4 Sep 2019 08:39:09 +0000 (16:39 +0800)]
ASoC: tegra: use devm_platform_ioremap_resource() to simplify code

Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.

Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904083909.18804-1-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: sirf-audio: use devm_platform_ioremap_resource() to simplify code
YueHaibing [Wed, 4 Sep 2019 08:34:12 +0000 (16:34 +0800)]
ASoC: sirf-audio: use devm_platform_ioremap_resource() to simplify code

Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.

Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904083412.18700-1-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: ep93xx: use devm_platform_ioremap_resource() to simplify code
YueHaibing [Wed, 4 Sep 2019 08:25:07 +0000 (16:25 +0800)]
ASoC: ep93xx: use devm_platform_ioremap_resource() to simplify code

Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.

Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904082507.24300-1-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: amd: use devm_platform_ioremap_resource() to simplify code
YueHaibing [Wed, 4 Sep 2019 07:48:33 +0000 (15:48 +0800)]
ASoC: amd: use devm_platform_ioremap_resource() to simplify code

Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.

Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904074833.23572-1-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: es8316: add clock control of MCLK
Katsuhiro Suzuki [Tue, 3 Sep 2019 16:53:20 +0000 (01:53 +0900)]
ASoC: es8316: add clock control of MCLK

This patch introduce clock property for MCLK master freq control.
Driver will set rate of MCLK master if set_sysclk is called and
changing sysclk by board driver.

[Modified slightly to apply without an earlier patch in the series due
to context diffs -- broonie]

Signed-off-by: Katsuhiro Suzuki <katsuhiro@katsuster.net>
Link: https://lore.kernel.org/r/20190903165322.20791-2-katsuhiro@katsuster.net
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: es8316: add DT-bindings
Katsuhiro Suzuki [Tue, 3 Sep 2019 16:53:22 +0000 (01:53 +0900)]
ASoC: es8316: add DT-bindings

This patch adds missing DT-bindings document for Everest ES8316.

Signed-off-by: Katsuhiro Suzuki <katsuhiro@katsuster.net>
Link: https://lore.kernel.org/r/20190903165322.20791-4-katsuhiro@katsuster.net
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: audio-graph: indicate rebind issue
Kuninori Morimoto [Tue, 3 Sep 2019 08:16:05 +0000 (17:16 +0900)]
ASoC: audio-graph: indicate rebind issue

ALSA SoC try to rebind Sound Card if Card/CPU/Codec/Platform
were unbinded and re-binded again.
But, Audio Graph Card might can't rebind again if user do for example

unbind CPU or Codec driver
bind   CPU or Codec driver

Because Audio Graph Card is still pointing old/unbinded
CPU or Codec driver's DAI name at dlc->dai_name.

To avoid this issue, it needs to alloc memory and keep DAI name
even though if CPU or Codec driver was unbinded.
Or, always do unbind/bind at Sound Card.

For now, this patch indicates this issue as FIXME.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87sgpdu75m.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: simple-card: indicate rebind issue
Kuninori Morimoto [Tue, 3 Sep 2019 08:15:54 +0000 (17:15 +0900)]
ASoC: simple-card: indicate rebind issue

ALSA SoC try to rebind Sound Card if Card/CPU/Codec/Platform
were unbinded and re-binded again.
But, Simple Card might can't rebind again if user do for example

unbind CPU or Codec driver
bind   CPU or Codec driver

Because Simple Card is still pointing old/unbinded
CPU or Codec driver's DAI name at dlc->dai_name.

To avoid this issue, it needs to alloc memory and keep DAI name
even though if CPU or Codec driver was unbinded.
Or, always do unbind/bind at Sound Card.

For now, this patch indicates this issue as FIXME.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87tv9tu75x.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: soc-core: move soc_probe_link_components() position
Kuninori Morimoto [Fri, 23 Aug 2019 00:58:58 +0000 (09:58 +0900)]
ASoC: soc-core: move soc_probe_link_components() position

It is easy to read code if it is cleanly using paired function/naming,
like start <-> stop, register <-> unregister, etc, etc.
But, current ALSA SoC code is very random, unbalance, not paired, etc.
It is easy to create bug at the such code, and it will be difficult to
debug.

soc_probe_link_components() has paired soc_remove_link_components(),
but, these are implemented at different place.
So it is difficult to confirm code.
This patch moves soc_probe_link_components() next to
soc_remove_link_components().

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87o90g7lbd.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: soc-core: add snd_soc_dapm_init()
Kuninori Morimoto [Fri, 23 Aug 2019 00:58:52 +0000 (09:58 +0900)]
ASoC: soc-core: add snd_soc_dapm_init()

It is easy to read code if it is cleanly using paired function/naming,
like start <-> stop, register <-> unregister, etc, etc.
But, current ALSA SoC code is very random, unbalance, not paired, etc.
It is easy to create bug at the such code, and it will be difficult to
debug.

soc-dapm has snd_soc_dapm_free() which cleanups debugfs, widgets, list.
But, there is no paired initialize function.
This patch adds snd_soc_dapm_init() and initilaizing dapm

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87pnkw7lbj.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: soc-core: dapm related setup at one place
Kuninori Morimoto [Fri, 23 Aug 2019 00:58:47 +0000 (09:58 +0900)]
ASoC: soc-core: dapm related setup at one place

Current ASoC setups some dapm related member at
snd_soc_component_initialize() which is called when component was
registered, and setups remaining member at soc_probe_component()
which is called when component was probed.
This kind of setup separation is no meanings, and it is very
difficult to read and confusable.
This patch setups all dapm settings at one place.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87r25c7lbo.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: soc-core: move soc_probe_component() position
Kuninori Morimoto [Fri, 23 Aug 2019 00:58:42 +0000 (09:58 +0900)]
ASoC: soc-core: move soc_probe_component() position

It is easy to read code if it is cleanly using paired function/naming,
like start <-> stop, register <-> unregister, etc, etc.
But, current ALSA SoC code is very random, unbalance, not paired, etc.
It is easy to create bug at the such code, and it will be difficult to
debug.

soc_probe_comonent() has paired soc_remove_comonent(),
but, these are implemented at different place.
So it is difficult to confirm code.
This patch moves soc_probe_component() next to
soc_remove_component().

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87sgps7lbt.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: soc-core: add soc_rtd_free()
Kuninori Morimoto [Fri, 23 Aug 2019 00:58:37 +0000 (09:58 +0900)]
ASoC: soc-core: add soc_rtd_free()

It is easy to read code if it is cleanly using paired function/naming,
like start <-> stop, register <-> unregister, etc, etc.
But, current ALSA SoC code is very random, unbalance, not paired, etc.
It is easy to create bug at the such code, and it will be difficult to
debug.

soc_rtd_init() was soc_post_component_init(), but there was no
its paired soc_post_component_free(), but it is done at
soc_remove_link_dais().
This means it is difficult to find related code.

This patch adds soc_rtd_free() which is paired soc_rtd_init().
soc_rtd_xxx() will be more cleanuped in the future.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87tva87lby.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: dt-bindings: Convert Allwinner A64 analog codec to a schema
Maxime Ripard [Wed, 28 Aug 2019 12:52:09 +0000 (14:52 +0200)]
ASoC: dt-bindings: Convert Allwinner A64 analog codec to a schema

The Allwinner A64 SoC has an embedded audio codec that uses a separate
controller to drive its analog part, which is supported in Linux, with a
matching Device Tree binding.

Now that we have the DT validation in place, let's convert the device tree
bindings for that controller over to a YAML schemas.

Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://lore.kernel.org/r/20190828125209.28173-5-mripard@kernel.org
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: dt-bindings: Convert Allwinner A33 codec to a schema
Maxime Ripard [Wed, 28 Aug 2019 12:52:07 +0000 (14:52 +0200)]
ASoC: dt-bindings: Convert Allwinner A33 codec to a schema

The Allwinner A33 SoC have an embedded audio codec that is supported in Linux,
with a matching Device Tree binding.

Now that we have the DT validation in place, let's convert the device tree
bindings for that controller over to a YAML schemas.

Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://lore.kernel.org/r/20190828125209.28173-3-mripard@kernel.org
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: dt-bindings: sun4i-spdif: Fix dma-names warning
Maxime Ripard [Wed, 28 Aug 2019 12:52:05 +0000 (14:52 +0200)]
ASoC: dt-bindings: sun4i-spdif: Fix dma-names warning

Even though the H6 compatible has been properly added, the exeption for the
number of DMA channels hasn't been updated, leading in a validation
warning.

Fix this.

Fixes: b20453031472 ("dt-bindings: sound: sun4i-spdif: Add Allwinner H6 compatible")
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://lore.kernel.org/r/20190828125209.28173-1-mripard@kernel.org
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: mediatek: mt8183: fix space issues
Tzung-Bi Shih [Fri, 30 Aug 2019 07:42:40 +0000 (15:42 +0800)]
ASoC: mediatek: mt8183: fix space issues

Fix space issues:
- No space before ';'.
- No trailing blank line.

Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20190830074240.195166-5-tzungbi@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: mediatek: mt8183: remove forward declaration of headset_init
Tzung-Bi Shih [Fri, 30 Aug 2019 07:42:39 +0000 (15:42 +0800)]
ASoC: mediatek: mt8183: remove forward declaration of headset_init

The forward declaration of mt8183_mt6358_ts3a227_max98357_headset_init
is for cyclic dependency between card, headset_dev, and headset_init.

It used to be:
- card depends on headset_dev
- headset_dev depends on headset_init
- headset_init depends on card

Commit a962a809e5e4 ("ASoC: mediatek: mt8183: make headset codec
optional") removed the cyclic dependency.

Thus, it is safe to remove the forward declaration.

Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20190830074240.195166-4-tzungbi@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: mediatek: mt8183: move headset jack to card-specific storage
Tzung-Bi Shih [Fri, 30 Aug 2019 07:42:38 +0000 (15:42 +0800)]
ASoC: mediatek: mt8183: move headset jack to card-specific storage

Move headset jack descriptor from module global scope to card-specific
storage to make its ownership more explicit.

Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20190830074240.195166-3-tzungbi@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: mediatek: mt8183: move private structure
Tzung-Bi Shih [Fri, 30 Aug 2019 07:42:37 +0000 (15:42 +0800)]
ASoC: mediatek: mt8183: move private structure

Move private structure to the beginning of file to declare earlier
so that most functions can see it.

Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20190830074240.195166-2-tzungbi@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: SOF/Intel: fix selection of SND_INTEL_NHTL
Pierre-Louis Bossart [Thu, 29 Aug 2019 21:42:13 +0000 (16:42 -0500)]
ASoC: SOF/Intel: fix selection of SND_INTEL_NHTL

We should only select SND_INTEL_NHLT when ACPI is defined. This was
done for the legacy HDAudio driver but not for DSP-enabled cases,
leading to compilation errors with randconfig.

Fix by aligning on the same solution.

For the Skylake driver this is overkill since there is a top-level
dependency on ACPI, but it doesn't hurt and it's better to have
consistency.

Fixes: 68b953aeb50d9 ('ASoC: SOF: Intel: hda: fixup HDaudio topology name with DMIC number')
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190829214213.11653-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: Intel: broadwell: Simplify device probe
Cezary Rojewski [Thu, 22 Aug 2019 11:36:16 +0000 (13:36 +0200)]
ASoC: Intel: broadwell: Simplify device probe

With legacy ADSP private context adjusted, there is no need for double
safety.

Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20190822113616.22702-5-cezary.rojewski@intel.com
Tested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: Intel: bdw-rt5677: Simplify device probe
Cezary Rojewski [Thu, 22 Aug 2019 11:36:15 +0000 (13:36 +0200)]
ASoC: Intel: bdw-rt5677: Simplify device probe

With legacy ADSP private context adjusted, there is no need for double
safety.

Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20190822113616.22702-4-cezary.rojewski@intel.com
Tested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: Intel: haswell: Simplify device probe
Cezary Rojewski [Thu, 22 Aug 2019 11:36:14 +0000 (13:36 +0200)]
ASoC: Intel: haswell: Simplify device probe

With legacy ADSP private context adjusted, there is no need for double
safety.

Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20190822113616.22702-3-cezary.rojewski@intel.com
Tested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: Intel: Haswell: Adjust machine device private context
Cezary Rojewski [Thu, 22 Aug 2019 11:36:13 +0000 (13:36 +0200)]
ASoC: Intel: Haswell: Adjust machine device private context

Apart from Haswell machines, all other devices have their private data
set to snd_soc_acpi_mach instance.

Changes for HSW/ BDW boards introduced with series:
https://patchwork.kernel.org/cover/10782035/

added support for dai_link platform_name adjustments within card probe
routines. These take for granted private_data points to
snd_soc_acpi_mach whereas for Haswell, it's sst_pdata instead. Change
private context of platform_device - representing machine board - to
address this.

Fixes: e87055d732e3 ("ASoC: Intel: haswell: platform name fixup support")
Fixes: 7e40ddcf974a ("ASoC: Intel: bdw-rt5677: platform name fixup support")
Fixes: 2d067b2807f9 ("ASoC: Intel: broadwell: platform name fixup support")
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20190822113616.22702-2-cezary.rojewski@intel.com
Tested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: ti: davinci-evm: Do not fail if the dai_set_sysclk returns -ENOTSUPP
Peter Ujfalusi [Fri, 30 Aug 2019 10:38:41 +0000 (13:38 +0300)]
ASoC: ti: davinci-evm: Do not fail if the dai_set_sysclk returns -ENOTSUPP

The davinci McBSP (davinci-i2s) driver does not implement the set_sysclk
callback, which is fine and should not be treated as error.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20190830103841.25128-5-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: ti: edma-pcm: Fix for legacy dma_slave_map based channel lookup
Peter Ujfalusi [Fri, 30 Aug 2019 10:38:40 +0000 (13:38 +0300)]
ASoC: ti: edma-pcm: Fix for legacy dma_slave_map based channel lookup

Most of the daVinci devices does not boot with DT. In this case the DMA
channel is looked up with dma_slave_map and for that the chan_names[]
must be configured.

Both McASP and ASP/McBSP uses "tx" and "rx" as channel names, so we can
just do this when the dev->of_node is not valid.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20190830103841.25128-4-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: ti: davinci-i2s: Add S32_LE as support format
Peter Ujfalusi [Fri, 30 Aug 2019 10:38:38 +0000 (13:38 +0300)]
ASoC: ti: davinci-i2s: Add S32_LE as support format

ASP/McBSP can support 8/16/20/24/32 bits word in theory. I have only tested
S16_LE and S32_LE, the other formats might not work so only extend the
supported formats with S32_LE for now.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20190830103841.25128-2-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: wcd9335: Fix primary interpolator max rate
Srinivas Kandagatla [Thu, 22 Aug 2019 09:56:51 +0000 (10:56 +0100)]
ASoC: wcd9335: Fix primary interpolator max rate

On this codec SLIMBus RX path supports 384000 rate on primary interpolator.
Add this missing rate as supported rate.

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20190822095653.7200-3-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoALSA: pcm: add support for 352.8KHz and 384KHz sample rate
Vidyakumar Athota [Thu, 22 Aug 2019 09:56:50 +0000 (10:56 +0100)]
ALSA: pcm: add support for 352.8KHz and 384KHz sample rate

Most of the modern codecs supports 352.8KHz and 384KHz sample rates.
Currenlty HW params fails to set 352.8Kz and 384KHz sample rate
as these are not in known rates list.
Add these new rates to known list to allow them.

This patch also adds defines in pcm.h so that drivers can use it.

Signed-off-by: Vidyakumar Athota <vathota@codeaurora.org>
Signed-off-by: Banajit Goswami <bgoswami@codeaurora.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20190822095653.7200-2-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: mediatek: mt8183: fix tdm out data is valid on rising edge
Jiaxin Yu [Sat, 24 Aug 2019 04:37:25 +0000 (12:37 +0800)]
ASoC: mediatek: mt8183: fix tdm out data is valid on rising edge

This patch correct tdm out bck inverse register to AUDIO_TOP_CON3[3].

Signed-off-by: Jiaxin Yu <jiaxin.yu@mediatek.com>
Link: https://lore.kernel.org/r/1566621445-26989-4-git-send-email-jiaxin.yu@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: mediatek: mt8183: tdm hw support tdm out and 8ch i2s out
Jiaxin Yu [Sat, 24 Aug 2019 04:37:24 +0000 (12:37 +0800)]
ASoC: mediatek: mt8183: tdm hw support tdm out and 8ch i2s out

This patch refined tdm driver code, and allow tdm hw to support two
configurations in machine driver to output tdm signal or i2s signal.

Signed-off-by: Jiaxin Yu <jiaxin.yu@mediatek.com>
Link: https://lore.kernel.org/r/1566621445-26989-3-git-send-email-jiaxin.yu@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: atmel_ssc_dai: implement left-justified data mode
Michał Mirosław [Sat, 24 Aug 2019 20:26:54 +0000 (22:26 +0200)]
ASoC: atmel_ssc_dai: implement left-justified data mode

Enable support for left-justified data mode for SSC-codec link.

Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Link: https://lore.kernel.org/r/44fa6b700421e80778f20ff9ead2b148cf6d2e92.1566677788.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: atmel_ssc_dai: rework DAI format configuration
Michał Mirosław [Sat, 24 Aug 2019 20:26:53 +0000 (22:26 +0200)]
ASoC: atmel_ssc_dai: rework DAI format configuration

Rework DAI format calculation in preparation for adding more formats
later. As a side-effect this enables all CBM/CBS x CFM/CFS combinations
for supported formats. (Note: the additional modes are not tested.)

Note: this changes FSEDGE to POSITIVE for I2S CBM_CFS mode as the TXSYN
interrupt is not used anyway.

Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Link: https://lore.kernel.org/r/f5949b0326fdcdca072f3ed03f77de9e207631cd.1566677788.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: atmel: enable SOC_SSC_PDC and SOC_SSC_DMA in Kconfig
Michał Mirosław [Sat, 24 Aug 2019 20:26:52 +0000 (22:26 +0200)]
ASoC: atmel: enable SOC_SSC_PDC and SOC_SSC_DMA in Kconfig

Allow SSC to be used on platforms described using audio-graph-card
in Device Tree.

Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/233d5461f4448df151755de7b69a0cd3ad310d5c.1566677788.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: cs42xx8: Force suspend/resume during system suspend/resume
Shengjiu Wang [Tue, 27 Aug 2019 22:13:46 +0000 (18:13 -0400)]
ASoC: cs42xx8: Force suspend/resume during system suspend/resume

Use force_suspend/resume to make sure clocks are disabled/enabled
accordingly during system suspend/resume.

Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/1566944026-18113-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: Intel: Skylake: Release topology when we are done with it
Amadeusz Sławiński [Tue, 27 Aug 2019 14:17:11 +0000 (16:17 +0200)]
ASoC: Intel: Skylake: Release topology when we are done with it

Currently topology is kept in memory while driver is running. It's
unnecessary, as it's only needed during parsing.

Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20190827141712.21015-6-amadeuszx.slawinski@linux.intel.com
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: Intel: Skylake: Print module type instead of id
Amadeusz Sławiński [Tue, 27 Aug 2019 14:17:10 +0000 (16:17 +0200)]
ASoC: Intel: Skylake: Print module type instead of id

When we are printing module params, we were actually printing module id
instead of type, but debug message was saying that number we get is type.
So print module type, as it is useful when debugging paths, but also
keep printing module id, as it is used in all other logs.

Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@intel.com>
Link: https://lore.kernel.org/r/20190827141712.21015-5-amadeuszx.slawinski@linux.intel.com
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: SOF: imx8: Fix an is IS_ERR() vs NULL check
Dan Carpenter [Mon, 26 Aug 2019 13:18:55 +0000 (16:18 +0300)]
ASoC: SOF: imx8: Fix an is IS_ERR() vs NULL check

The device_link_add() function only returns NULL on error, it doesn't
return error pointers.

Fixes: 202acc565a1f ("ASoC: SOF: imx: Add i.MX8 HW support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/20190826131855.GA6840@mwanda
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: sun4i: Revert A83t description
Maxime Ripard [Tue, 27 Aug 2019 12:31:31 +0000 (14:31 +0200)]
ASoC: sun4i: Revert A83t description

The last set of reworks included some fixes to change the A83t behaviour
and "fix" it.

It turns out that the controller described in the datasheet and the one
supported here are not the same, yet the A83t has the two of them, and the
one supported in the driver wasn't the one described in the datasheet.

Fix this by reintroducing the proper quirks.

Fixes: 69e450e50ca6 ("ASoC: sun4i-i2s: Fix the LRCK period on A83t")
Fixes: bf943d527987 ("ASoC: sun4i-i2s: Fix MCLK Enable bit offset on A83t")
Fixes: 2e04fc4dbf50 ("ASoC: sun4i-i2s: Fix WSS and SR fields for the A83t")
Fixes: 515fcfbc7736 ("ASoC: sun4i-i2s: Fix LRCK and BCLK polarity offsets on newer SoCs")
Fixes: c1d3a921d72b ("ASoC: sun4i-i2s: Fix the MCLK and BCLK dividers on newer SoCs")
Fixes: fb19739d7f68 ("ASoC: sun4i-i2s: Use module clock as BCLK parent on newer SoCs")
Fixes: 71137bcd0a9a ("ASoC: sun4i-i2s: Move the format configuration to a callback")
Fixes: d70be625f25a ("ASoC: sun4i-i2s: Move the channel configuration to a callback")
Reported-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://lore.kernel.org/r/20190827123131.29129-2-mripard@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: SOF: imx8: Fix return value check in imx8_probe()
Wei Yongjun [Mon, 26 Aug 2019 12:00:03 +0000 (12:00 +0000)]
ASoC: SOF: imx8: Fix return value check in imx8_probe()

In case of error, the function devm_ioremap_wc() returns NULL pointer
not ERR_PTR(). The IS_ERR() test in the return value check should be
replaced with NULL test.

Fixes: 202acc565a1f ("ASoC: SOF: imx: Add i.MX8 HW support")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/20190826120003.183279-1-weiyongjun1@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: mediatek: mt8183: remove unused DAPM-related variables
Tzung-Bi Shih [Mon, 26 Aug 2019 03:26:42 +0000 (11:26 +0800)]
ASoC: mediatek: mt8183: remove unused DAPM-related variables

Remove unused variable mt8183_mt6358_ts3a227_max98357_dapm_widgets and
mt8183_mt6358_ts3a227_max98357_dapm_routes.  They are accidentially
included when rebasing commits.

Fixes: 6191cbde5ff0 ("ASoC: mediatek: mt8183: switch tdm pins gpio function when playback on or off")
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20190826032642.27324-1-tzungbi@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: sunxi: Revert initial A83t support
Maxime Ripard [Tue, 27 Aug 2019 09:32:05 +0000 (11:32 +0200)]
ASoC: sunxi: Revert initial A83t support

This reverts commit 3e9acd7ac6933c (ASoC: sun4i-i2s: Remove
duplicated quirks structure").

It turns out that while one I2S controller is described in the A83t
datasheet, the driver supports another, undocumented, one that has been
inherited from the older SoCs, while the documented one uses the new
design.

Fixes: 3e9acd7ac693 ("ASoC: sun4i-i2s: Remove duplicated quirks structure")
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://lore.kernel.org/r/20190827093206.17919-1-mripard@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: imx-audmix: register the card on a proper dev
Shengjiu Wang [Tue, 27 Aug 2019 15:55:15 +0000 (11:55 -0400)]
ASoC: imx-audmix: register the card on a proper dev

This platform device is registered from "fsl_audmix", which is
its parent device. If use pdev->dev.parent for the priv->card.dev,
the value set by dev_set_drvdata in parent device will be covered
by the value in child device.

Fixes: b86ef5367761 ("ASoC: fsl: Add Audio Mixer machine driver")
Signed-off-by: Viorel Suman <viorel.suman@nxp.com>
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/1566921315-23402-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: SOF: imx8: Make some functions static
YueHaibing [Fri, 23 Aug 2019 12:59:39 +0000 (20:59 +0800)]
ASoC: SOF: imx8: Make some functions static

Fix sparse warnings:

sound/soc/sof/imx/imx8.c:104:6: warning: symbol 'imx8_dsp_handle_reply' was not declared. Should it be static?
sound/soc/sof/imx/imx8.c:115:6: warning: symbol 'imx8_dsp_handle_request' was not declared. Should it be static?
sound/soc/sof/imx/imx8.c:336:5: warning: symbol 'imx8_get_bar_index' was not declared. Should it be static?
sound/soc/sof/imx/imx8.c:341:6: warning: symbol 'imx8_ipc_msg_data' was not declared. Should it be static?
sound/soc/sof/imx/imx8.c:348:5: warning: symbol 'imx8_ipc_pcm_params' was not declared. Should it be static?

Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/20190823125939.30012-1-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
5 years agoASoC: soc-core: rename soc_post_component_init() to soc_rtd_init()
Kuninori Morimoto [Fri, 23 Aug 2019 00:58:32 +0000 (09:58 +0900)]
ASoC: soc-core: rename soc_post_component_init() to soc_rtd_init()

It is easy to read code if it is cleanly using paired function/naming,
like start <-> stop, register <-> unregister, etc, etc.
But, current ALSA SoC code is very random, unbalance, not paired, etc.
It is easy to create bug at the such code, and it will be difficult to
debug.

From function name point of view, "soc_post_component_init()" sounds
like "component initialize function".
But in reality it is rtd setup function.

This patch renames soc_post_component_init() to soc_rtd_init()

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87v9uo7lc3.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>