gxfb/lxfb: detect framebuffer size using an MSR if VSA2 isn't available

If there's no VSA2 (ie, if we're using tinybios or OpenFirmware), use the
GLIU's P2D Range Offset Descriptor to determine how much memory we have
available for the framebuffer.

Originally based on a patch by Jordan Crouse.  Tested with OpenFirmware;
Pascal informs me that tinybios has a stub that fills in P2D_RO0.

Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

gxfb/lxfb: use VSA definitions when fetching framebuffer size

..Rather than using magic constants.

Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

lxfb/gxfb: when blanking with FB_BLANK_POWERDOWN, also turn off the CRT

The Display Control's CRT_EN can be shut off when we enter FB_BLANK_POWERDOWN
in an attempt to save additional power.

Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

lxfb: disable suspend VT switch by default

By default disable VT switch, but allow it to be overridden via the
'vt_switch' module arg.

Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

lxfb: rename kernel arg fbsize to vram

Match other fb drivers (including gxfb).  Also, document the current boot
arguments in Documentation/fb/lxfb.txt.

Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

lxfb: add power management functionality

This adds the ability to suspend/resume the lxfb driver, which includes:
  - Register and palette saving code; registers are stored in lxfb_par.
    A few MSR values are saved as well.
  - lx_powerup and lx_powerdown functions which restore/save registers and
    enable/disable graphic engines.
  - lxfb_suspend/lxfb_resume

Originally based on a patch by Jordan Crouse.

[akpm@linux-foundation.org: be conventional, save an ifdef]
Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

lxfb: rearrange/rename MSR bitfields

Finally, move the MSR bitfields around in lxfb.h, and rename them.  Alas, most
of that crap appears to be undocumented.

Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

lxfb: clean up final bits of df_regs

Finally drop the last remnants of df_regs, using vp_regs instead.  Also, drop
panel_width and panel_height from lxfb_par; they're unused.

Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

lxfb: clean up register definitions

 - Rename various bitfield defines to match the data sheet names.
 - Rename DF_ register definitions to VP_ to match the data sheet;
   ie, DF_PAR -> VP_PAR.
 - for GP/DC registers, rather than defining to specific addresses, use
   an enum to number them sequentially and just multiply by 4 (bytes) to
   access them (in read_*/write_* functions).
 - for VP/FP registers, use an enum and multiple by 8 (bytes).  They're
   64bit registers.

Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

lxfb: create GP/DC/VP/FP-specific handlers rather than using readl/writel

This creates read_gp/write_gp, read_dc/write_dc, read_vp/write_vp, and
read_fp/write_fp for reading and updating those registers.  Note that we don't
follow the 'DF' naming; those will be renamed to VP shortly.

Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

lxfb: extend PLL table to support dotclocks below 25 MHz

Extends the PLL frequency table of the AMD Geode-LX frame buffer driver to
make use of the DIV4 bit, thus adding support for dotclocks between 6 and 25
MHz.  These are needed for small LCDs (e.g.  320x240).  Also inserts some
intermediate steps between pre-existing frequencies.

Signed-off-by: Jens Rottmann <JRottmann@LiPPERT-AT.de>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

atmel_lcdfb: adjust fifo size for at91sam9rl

AT91SAM9RL soc has a 2048 bytes deep FIFO, like AT91SAM9263.

[bn@niasdigital.com: fix build breakage in atmel_lcdfb]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Nicolas FERRE <nicolas.ferre@rfo.atmel.com>
Cc: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

atmel_lcdfb: wiring BGR to RGB color mode

Adds different wiring mode for the LCD screen.

The legacy atmel LCDC IP uses a non standard color mode, "BGR-555.1" instead
"RGB-565".  The major part of graphic stacks for embedded systems uses only
"RGB-565".  It is possible to swap LCD IOs instead of doing this bit swapping
by software (See application note AT91SAM9 LCD Controller
http://www.atmel.com/dyn/resources/prod_documents/doc6300.pdf)

This wire swapping is done on the at91sam9rl-ek board (board code
using this patch will come later).

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Andrew Victor <avictor.za@gmail.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

atmel_lcdfb: suspend/resume support

Teach atmel_lcdfb driver how to suspend/resume.

Note that the backlight control should probably do more of the same stuff:
turning off display power (more than just the backlight) and stopping the
clocks (and dma to drive the no-longer-seen display).  No point in wasting
power to generate images that can't be observed, after all...

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Andrew Victor <avictor.za@gmail.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

atmel_lcdfb: don't initialize a pre-allocated framebuffer

If the user specified a fixed framebuffer address on the command line, it may
have been initialized already with a splash image or something, so we
shouldn't clear it.

Therefore, we should only initialize the framebuffer if we allocated it
ourselves.  This patch also updates the AVR32 setup code to clear the
framebuffer if it allocated it itself, i.e.  the user didn't provide a fixed
address or the reservation failed.

I've updated the at91 platform code as well so that it initializes the
framebuffer if it is located in SRAM, but I haven't tested that it actually
works.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Nicolas FERRE <nicolas.ferre@rfo.atmel.com>
Cc: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fbdev: framebuffer_alloc() fixes

Correct the dev arg of framebuffer_alloc() in arkfb, s3fb and vt8623fb.

Signed-off-by: Ondrej Zajicek <santiago@crfreenet.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fbdev: vt8623fb: better resume from STR

After resume from STR, image is shifted by 8 pixels to the left.  This patch
fixes it.

Signed-off-by: Ondrej Zajicek <santiago@crfreenet.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

savagefb: speed up the I2C bus

There is no reason to drive the savagefb I2C bus at such a low speed, so bump
it from 12.5 kbps to 50 kbps.  The Intel (i810) and Matrox framebuffer drivers
already run their I2C bus at this speed, and so are the legacy i2c-savage4 and
i2c-prosavage drivers.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/video/imsttfb.c: add missing curly brackets

in #if 0 inactivated function msttfb_load_cursor_image() the call eieio()
occurs after rather than in the loop due to missing curly brackets.

Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

uvesafb: don't treat valid modes returned byfb_find_mode() as errors

Don't treat valid modes returned by fb_find_mode() (best-fit modes, default
modes or the first valid mode) as errors.

Currently, when fb_find_mode() finds a valid mode belonging to one of the
above-mentioned classes, uvesafb will ignore it and will try to set a 640x480
video mode.  The expected behaviour (introduced by this patch) would be to use
the valid mode returned by fb_find_mode() instead.

Signed-off-by: Michal Januszewski <spock@gentoo.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

radeonfb: speed up the I2C buses

There is no reason to drive the radeon I2C buses at such a low speed, so bump
it from 12.5 kbps to 50 kbps.  The Intel (i810) and Matrox framebuffer drivers
already run their I2C bus at this speed.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

radeonfb: drop redundant RTRACE macro

RTRACE() does exactly the same thing as the standard pr_debug() call, so just
use the latter.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

radeonfb: fix debug option

Fix CONFIG_FB_RADEON_DEBUG.  DEBUG must be defined before including any kernel
header, otherwise dev_dbg() resolves to a no-op.  Also, when debugging is
disabled, don't set DEBUG at all instead of setting it to 0, to comply with
what the kernel headers expect.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

radeonfb: use PCI device id in hex for name string

Additionally provide PCI device id in character format if possible.  (The
printable characters were commonly used to identify the cards.)

Signed-off-by: Andreas Herrmann <aherrman@arcor.de>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/video/aty/aty128fb.c: fix incorrect usage of strncat in aty128_init()

Fix incorrect length for strncat by replacing it with strlcat

Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fbdev: add removed option "mode" to keep compatibility

Add removed option "mode" to keep compatibility with existing setups.  The
option is back for pm2fb, tridentfb and vt8623fb drivers.

Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

s3fb: add option mode_option

Add the option "mode_option".  It also moves mtrr variable to devinitdata
section.

Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

arkfb: add option mode_option

Add the option "mode_option".  This is one step toward changing all fb
drivers to have common "mode_option" parameter.

Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

vt8623fb: change option mode to mode_option

Change the option "mode" into "mode_option".

This is one step toward changing all fb drivers to have common "mode_option"
parameter.

Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

update modedb.txt documentation about mode_option parameter change

Add names of drivers converted to "mode_option" parameter.

This is one step toward changing all fb drivers to have common "mode_option"
parameter.

Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

pm3fb: change option mode to mode_option

Add the option "mode_option".

This is one step toward changing all fb drivers to have common "mode_option"
parameter.

Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

tridentfb: change option mode to mode_option

Change the option "mode_option" into "mode".  It also adds __init attribute to
tridentfb_setup function.

This is one step toward changing all fb drivers to have common "mode_option"
parameter.

Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Alain Kalker <miki@dds.nl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

pm2fb: change option mode to mode_option

Change the option "mode_option" into "mode".

This is one step toward changing all fb drivers to have common "mode_option"
parameter.

Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Alain Kalker <miki@dds.nl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

video/aty/atyfb_base.c: free when fb can't be registered

Free buffer when the framebuffer can't be registered

Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fbmem: fix con2fbmap limit check

Fix limit check in FBIOPUT_CON2FBMAP ioctl.

Signed-off-by: Peter Samuelson <peter@p12n.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

PM/gxfb: add hook to PM console layer that allows disabling of suspend VT switch

Prior to suspend, we allocate and switch to a new VT; after suspend, we switch
back to the original VT.  This can be slow, and is completely unnecessary if
the framebuffer we're using can restore video properly.

This adds a hook that allows drivers to select whether or not to do this vt
switch, and changes the gxfb driver to call this hook.  It also adds a module
param to gxfb to allow controlling of the vt switch (defaulting to no switch).

(Note: I'm not convinced that console_sem is the best way to protect this, but
we should probably have some form of locking..)

[akpm@linux-foundation.org: build fix]
Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

gxfb: add power management functionality

This adds the ability to suspend/resume the gxfb driver, which includes:
  - The addition of a Graphics Processor register table in gxfb.h, and
    associated GP handling.
  - Register and palette saving code; registers are stored in gxfb_par.
    A few MSR values are saved as well.
  - gx_powerup and gx_powerdown functions which restore/save registers and
    enable/disable graphic engines.
  - gxfb_suspend/gxfb_resume

Originally based on a patch by Jordan Crouse.

Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

gxfb: stop sharing code with gx1fb

We want to stop sharing stuff with gx1fb; it makes little sense.  There were
fields in geodefb_par that weren't being used, there was little point to the
DC/VP ops callbacks, etc.  This implements the following:

  - Create gxfb_par (based on geodefb_par), place it in gxfb.h
  - Drop display_gx.h and video_gx.h.  The last few patches moved most
    stuff into gxfb.h anyways, so there was very little left.
  - Drop the geode_{dc,vid}_ops stuff.  Un-static functions, add
    declarations to gxfb.h.

Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

gxfb: move MSR bit fields into gxfb.h

This continues the gxfb header cleanups.  MSRs are defined in geode.h; the
specific bits we care about are defined in gxfb.h.

Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

gxfb: clean up register definitions

This does the following in preparation for register saving:
  - moves the register definitions from video_gx.h and display_gx.h into
    gxfb.h.
  - renames GX_* registers to match their section (ie, VP_).
  - renames register bitfields to match the data sheet (ie,
    DC_DCFG_TGEN -> DC_DISPLAY_CFG_TGEN).
  - for DC registers, rather than defining to specific addresses, use
    an enum to number them sequentially and just multiply by 4(bytes) to
    access them (in read_dc/write_dc).
  - for VP and FP registers, use an enum and multiple by 8 (bytes).  They're
    64bit registers.

Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

gxfb: create DC/VP/FP-specific handlers rather than using readl/writel

This creates read_dc/write_dc, read_vp/write_vp, and read_fp/write_fp for
reading and updating those registers.  It creates gxfb.h to house these.

We also drop a no-op readl() from gx_set_mode.  Other than that, there should
be no functionality change.

Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

gxfb: replace FBSIZE config option with a module parameter

Use a command line option (vram) rather than hardcoding the vram size.  LxFB
already does this; it's useful for machines that can't query the BIOS for fb
size.  This patch originated from David Woodhouse, was modified by Jordan
Crouse, and was then modified further by me.

This also adds some gxfb documentation in Documentation/fb.

Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

gxfb: use PCI_DEVICE() for gxfb's pci device table

Drop the class/class_mask stuff; it's unnecessary as long as the vendor and
device IDs match.

Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

gxfb: don't enable the CRT DACs when we are in flatpanel mode

When the FP strap is enabled, don't turn on the CRT DACs - that will save
about 35 mA of power.

Updated/cleaned up by Andres Salomon.

Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

gxfb: set the right registers to tweak the sync polarity

While running in flatpanel mode it is important to change the FP sync bits (VG
register 0x408) rather then the CRT sync bits (VG register 0x008).  This patch
keeps the CRT sync bits at default when a flatpanel exists.

Note that this also fixes inverted logic; we want CRT_VSYNC_POL to be set (ie,
vsync is normally high) when FB_SYNC_VERT_HIGH_ACT is unset.

Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

x86: GEODE: add Virtual Systems Architecture detection

This is generic VSA2 detection.  It's used by OLPC to determine whether or not
the BIOS contains VSA2, but since other BIOSes are coming out that don't use
the VSA (ie, tinybios), it might end up being useful for others.

Signed-off-by: Andres Salomon <dilinger@debian.org>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

x86: geode: MSR cleanup

This cleans up a few MSR-using drivers in the following manner:
  - Ensures MSRs are all defined in asm/geode.h, rather than in misc
    places
  - Makes the naming consistent; cs553[56] ones begin with MSR_,
    GX-specific ones start with MSR_GX_, and LX-specific ones start
    with MSR_LX_.  Also, make the names match the data sheet.
  - Use MSR names rather than numbers in source code
  - Document the fact that the LX's MSR_PADSEL has the wrong value
    in the data sheet.  That's, uh, good to note.

Signed-off-by: Andres Salomon <dilinger@debian.org>
Acked-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fbcon: replace mono_col macro with static inline

Use __u32 for max_len to match the declaration of length in the struct
fb_bitfield.

Suppresses sparse shadowed variable warnings from the nested max()
macros:
drivers/video/console/fbcon.h:130:8: warning: symbol '_x' shadows an earlier one
drivers/video/console/fbcon.h:130:8: originally declared here
drivers/video/console/fbcon.h:130:8: warning: symbol '_x' shadows an earlier one
drivers/video/console/fbcon.h:130:8: originally declared here
drivers/video/console/fbcon.h:130:8: warning: symbol '_y' shadows an earlier one
drivers/video/console/fbcon.h:130:8: originally declared here

[akpm@linux-foundation.org: fix constness]
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

pm2fb: correct error values returned from probe function

Fix error values returned in some code branches in the pm2fb_probe() function.

Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fbdev: use DIV_ROUND_UP or roundup

The kernel.h macro DIV_ROUND_UP performs the computation (((n) + (d) - 1) /
(d)) but is perhaps more readable.

An extract of the semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@haskernel@
@@

#include <linux/kernel.h>

@depends on haskernel@
expression n,d;
@@

(
- (n + d - 1) / d
+ DIV_ROUND_UP(n,d)
|
- (n + (d - 1)) / d
+ DIV_ROUND_UP(n,d)
)

@depends on haskernel@
expression n,d;
@@

- DIV_ROUND_UP((n),d)
+ DIV_ROUND_UP(n,d)

@depends on haskernel@
expression n,d;
@@

- DIV_ROUND_UP(n,(d))
+ DIV_ROUND_UP(n,d)
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

powerpc: offb: add support for foreign endianness

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fb: add support for foreign endianness

Add support for the framebuffers with non-native endianness.  This is done via
FBINFO_FOREIGN_ENDIAN flag that will be used by the drivers.  Depending on the
host endianness this flag will be overwritten by FBINFO_BE_MATH internal flag,
or cleared.

Tested to work on MPC8360E-RDK (BE) + Fujitsu MINT framebuffer (LE).

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: <Valdis.Kletnieks@vt.edu>
Cc: Clemens Koller <clemens.koller@anagramm.de>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fbdev: make the best-fit section of fb_find_mode return the closest matching mode

Currently, if a perfect match in terms of resolution is not found,
fb_find_mode() only looks for a best-fit mode among modes with a higher
resolution than the one requested.  Thus, if the user requests a resolution
higher than the largest supported one, they are dropped to the default mode
(usually a low resolution one).

Change this behaviour so that all valid video modes are considered when
looking for a best-fit mode, while still preferring modes with a higher
resolution.

Signed-off-by: Michal Januszewski <spock@gentoo.org>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

gpiochip_reserve()

Add a new function gpiochip_reserve() to reserve ranges of gpios that platform
code has pre-allocated.  That is, this marks gpio numbers which will be
claimed by drivers that haven't yet been loaded, and thus are not available
for dynamic gpio number allocation.

[akpm@linux-foundation.org: remove unneeded __must_check]
[david-b@pacbell.net: don't export gpiochip_reserve (section fix)]
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

gpiolib: dynamic gpio number allocation

If gpio_chip->base is negative during registration, gpiolib performs dynamic
base allocation.  This is useful for devices that aren't always present, such
as GPIOs on hotplugged devices rather than mainboards.  (This behavior was
previously specified but not implemented.)

To avoid using any numbers that may have been explicitly assigned but not yet
registered, this dynamic allocation assigns GPIO numbers from the biggest
number on down, instead of from the smallest on up.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

gpio: define gpio_is_valid()

Introduce a gpio_is_valid() predicate; use it in gpiolib.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
    [ use inline function; follow the gpio_* naming convention;
      work without gpiolib; all programming interfaces need docs ]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

gpiolib: i2c/spi drivers: handle rmmod better

Use the newly introduced owner field in struct gpio_chip to protect the
current (small) set of non-SOC GPIO drivers from being unloaded while any of
their GPIOs are in use.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
[ add mcp23s08 and pcf857x ]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

gpiolib: better rmmod infrastructure

As long as one or more GPIOs on a gpio chip are used its driver should not be
unloaded.  The existing mechanism (gpiochip_remove failure) doesn't address
that, since rmmod can no longer be made to fail by having the cleanup code
report errors.  Module usecounts are the solution.

Assuming standard "initialize struct to zero" policies, this change won't
affect SOC platform drivers.  However, drivers for external chips (on I2C and
SPI busses) should be updated if they can be built as modules.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
[ gpio_ensure_requested() needs to update module usecounts too ]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

i2o: remove static inline forward declarations

Nothing in between of them and the later declaration with body
needs them.

Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

isdn: rename CONFIG_AVMB1_COMPAT to not look like a Kconfig variable

Since CONFIG_AVMB1_COMPAT is not a Kconfig variable, move it out of the
Kconfig namespace.

Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Acked-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

capifs: fix memory leak on remount

capifs_remount may reach 'return' statement without freeing of memory
allocated by kstrdup call

Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

hisax: depend on CONFIG_PNP, not __ISAPNP__

The PNP driver interfaces depend on CONFIG_PNP, so test that rather than
__ISAPNP__.

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

isdn: fix obvious cut-and-paste error in st5481_usb.c

Fix a rather obvious cut-and-paste error, where earlier code for the
controller URB got somehow mixed in with code for the interrupt URB.

Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

isdn: replace remaining __FUNCTION__ occurrences

__FUNCTION__ is gcc-specific, use __func__

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

eicon: fix sparse integer as NULL pointer warnings

drivers/isdn/hardware/eicon/message.c:745:47: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/eicon/message.c:761:45: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/eicon/message.c:9122:16: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/eicon/message.c:9147:16: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/eicon/message.c:9173:14: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/eicon/divasmain.c:396:23: warning: Using plain integer as NULL pointer

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Karsten Keil <kkeil@suse.de>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

avm: fix sparse warning using integer as NULL pointer

drivers/isdn/hardware/avm/b1isa.c:206:37: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/b1isa.c:208:33: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/b1.c:664:42: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/b1.c:666:44: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/b1.c:668:42: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/b1.c:791:37: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/b1.c:793:33: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/b1pci.c:385:37: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/b1pci.c:387:33: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/b1dma.c:886:42: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/b1dma.c:888:44: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/b1dma.c:890:42: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/b1dma.c:973:37: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/b1dma.c:975:33: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/b1pcmcia.c:204:37: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/b1pcmcia.c:206:33: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/t1isa.c:554:37: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/t1isa.c:556:33: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/t1pci.c:236:37: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/t1pci.c:238:33: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/c4.c:1091:42: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/c4.c:1093:44: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/c4.c:1095:42: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/c4.c:1170:21: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/c4.c:1294:37: warning: Using plain integer as NULL pointer
drivers/isdn/hardware/avm/c4.c:1296:33: warning: Using plain integer as NULL pointer

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Karsten Keil <kkeil@suse.de>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

capi: fix sparse warnings using integer as NULL pointer

drivers/isdn/capi/kcapi.c:829:30: warning: Using plain integer as NULL pointer
drivers/isdn/capi/kcapi.c:838:27: warning: Using plain integer as NULL pointer
drivers/isdn/capi/kcapi.c:954:17: warning: Using plain integer as NULL pointer
drivers/isdn/capi/kcapi.c:1007:37: warning: Using plain integer as NULL pointer
drivers/isdn/capi/kcapi.c:1009:33: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capiutil.c:453:24: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capilib.c:47:30: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capi.c:353:29: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capi.c:369:15: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capi.c:486:48: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capi.c:515:46: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capi.c:541:47: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capi.c:692:47: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capi.c:699:49: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capi.c:704:14: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capi.c:943:53: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capi.c:948:32: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capi.c:969:42: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capi.c:989:48: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capi.c:1026:69: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capi.c:1028:19: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capi.c:1061:20: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capi.c:1529:37: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capi.c:1531:33: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capidrv.c:338:15: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capidrv.c:758:32: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capidrv.c:880:40: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capidrv.c:407:15: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capidrv.c:429:49: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capidrv.c:407:15: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capidrv.c:444:49: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capidrv.c:429:49: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capidrv.c:429:49: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capidrv.c:429:49: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capidrv.c:429:49: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capidrv.c:429:49: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capidrv.c:1664:61: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capidrv.c:1969:37: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capidrv.c:2294:37: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capidrv.c:2297:33: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capidrv.c:2338:37: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capidrv.c:2341:33: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capifs.c:192:37: warning: Using plain integer as NULL pointer
drivers/isdn/capi/capifs.c:194:33: warning: Using plain integer as NULL pointer

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Karsten Keil <kkeil@suse.de>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

quota: convert stub functions from macros into inlines

Fixes things like this:

fs/super.c: In function `deactivate_super':
fs/super.c:182: warning: statement with no effect
fs/super.c: In function `do_remount_sb':
fs/super.c:644: warning: statement with no effect

Cc: Jan Kara <jack@ucw.cz>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

quota: reiserfs: make reiserfs handle quotaon on remount

Update reiserfs to handle quotaon on remount RW.

Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

quota: ext4: make ext4 handle quotaon on remount

Update ext4 to handle quotaon on remount RW.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

quota: ext3: make ext3 handle quotaon on remount

Update ext3 handle quotaon on remount RW.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

quota: quota core changes for quotaon on remount

Currently, we just turn quotas off on remount of filesystem to read-only
state.  The patch below adds necessary framework so that we can turn quotas
off on remount RO but we are able to automatically reenable them again when
filesystem is remounted to RW state.  All we need to do is to keep references
to inodes of quota files when remounting RO and using these references to
reenable quotas when remounting RW.

Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

quota: various style cleanups

Cleanups in quota code:
  Change __inline__ to inline.
  Change some macros to inline functions.
  Remove vfs_quota_off_mount() macro.
  DQUOT_OFF() should be (0) is CONFIG_QUOTA is disabled.
  Move declaration of mark_dquot_dirty and dirty_dquot from quota.h to dquot.c

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

quota: remove superfluous DQUOT_OFF() in fs/namespace.c

We don't need to turn quotas off before remounting root ro, because
do_remount_sb() already handles this.

Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

quota: do not allow setting of quota limits to too high values

We should check whether quota limits set via Q_SETQUOTA are not exceeding
limits which quota format is able to handle.

Signed-off-by: Andrew Perepechko <andrew.perepechko@sun.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kprobes: update document about batch registration

Add the description of batch registration interfaces to
Documentation/kprobes.txt.

Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Jim Keniston <jkenisto@us.ibm.com>
Cc: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Cc: Shaohua Li <shaohua.li@intel.com>
Cc: David Miller <davem@davemloft.net>
Cc: "Frank Ch. Eigler" <fche@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kprobes: add (un)register_jprobes for batch registration

Introduce unregister_/register_jprobes() for jprobe batch registration.

Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Jim Keniston <jkenisto@us.ibm.com>
Cc: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Cc: Shaohua Li <shaohua.li@intel.com>
Cc: David Miller <davem@davemloft.net>
Cc: "Frank Ch. Eigler" <fche@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kprobes: add (un)register_kretprobes for batch registration

Introduce unregister_/register_kretprobes() for kretprobe batch registration.

Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Jim Keniston <jkenisto@us.ibm.com>
Cc: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Cc: Shaohua Li <shaohua.li@intel.com>
Cc: David Miller <davem@davemloft.net>
Cc: "Frank Ch. Eigler" <fche@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kprobes: add (un)register_kprobes for batch registration

Introduce unregister_/register_kprobes() for kprobe batch registration.  This
can reduce waiting time for synchronized_sched() when a lot of probes have to
be unregistered at once.

Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Jim Keniston <jkenisto@us.ibm.com>
Cc: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Cc: Shaohua Li <shaohua.li@intel.com>
Cc: David Miller <davem@davemloft.net>
Cc: "Frank Ch. Eigler" <fche@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

list.h: add list_is_singular()

Add list_is_singular() to check a list has just one entry.

list_is_singular() is useful to check whether a list_head which have been
temporarily allocated for listing objects can be released or not.

Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kprobes: prevent probing of preempt_schedule()

Prohibit users from probing preempt_schedule().  One way of prohibiting the
user from probing functions is by marking such functions with __kprobes.  But
this method doesn't work for those functions, which are already marked to
different section like preempt_schedule() (belongs to __sched section).  So we
use blacklist approach to refuse user from probing these functions.

In blacklist approach we populate the blacklisted function's starting address
and its size in kprobe_blacklist structure.  Then we verify the user specified
address against start and end of the blacklisted function.  So any attempt to
register probe on blacklisted functions will be rejected.

[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Srinivasa DS <srinivasa@in.ibm.com>
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Jim Keniston <jkenisto@us.ibm.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

VT notifier extension for accessibility

Some accessibility modules need to be able to catch the output on the
console before the VT interpretation, and possibly swallow it.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mfd: use shorter set_current_state()

Since this routine declares a separate "tsk" pointer for no other reason than
to call set_task_state(), get rid of it and just invoke set_current_state().

Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Nicolas Pitre <nico@cam.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

sm501: add uart support

This patch extends the sm501 mfd with 8250 uart support. We're currently
doing this in the board specific r2d-1 code already, but it would be nice to
do move things into the mfd since it's more chip specific than board specific.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

spi: spi_imx updates

Updates to the i.MX SPI controller driver:

 1) Some comments changed and/or added.

 2) End of transfers is now managed on TXFIFO empty interrupt after the
    last write to TXFIFO.  This speeds interrupt execution by removing
    the wait for TXFIFO to become empty.  On TXFIFO empty interrupt the
    handler needs only to poll for the end of the ongoing transaction
    (SPI_CONTROL_XCH) to close the transfer.
     (2.1) Write only transfers are closed flushing RXFIFO.
     (2.2) Read transfers are closed reading trailing bytes from RXFIFO.
     (2.3) Read transfers where RXFIFO overrun occurred are closed by
           flushing RXFIFO and aborting the message.

 3) Fifos are now flushed via SPI disable after the end of ongoing
    transaction.

Signed-off-by: Andrea Paterniani <a.paterniani@swapp-eng.it>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

atmel_spi: support zero length transfer

A spi transfer with zero length is not invalid.  For example, such
transfer (len == 0 && delay_usecs != 0) can be used to achieve delay
before first CLK edge after chipselect assertion.

Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

spi: replace remaining __FUNCTION__ occurrences

__FUNCTION__ is gcc-specific, use __func__

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

documentation: move spidev_fdx example to its own source file

Move sample source code to its own source file so that it can be used
easier and build-tested/check/maintained by anyone.

(Makefile changes are in a separate patch for all of Documentation/.)

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

spi: pxa2xx_spi "sparse" fixes

Various cleanups to pxa2xx_spi suggested by "sparse": make sure that
register addresess are "void __iomem *", and make a few functions properly
static.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Ned Forrester <nforrester@whoi.edu>
Cc: Stephen Street <stephen@streetfiresound.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

spi: use menuconfig for CONFIG_SPI

Signed-off-by: Alessandro Guido <alessandro.guido@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

oprofile: change cpu_buffer from array to per_cpu variable

Change cpu_buffer from array to per_cpu variable in oprofile functions.

[akpm@linux-foundation.org: coding-style fixes]
Cc: Philippe Elie <phil.el@wanadoo.fr>
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

x86: configurable DMI scanning code

Turn CONFIG_DMI into a selectable option if EMBEDDED is defined, in
order to be able to remove the DMI table scanning code if it's not
needed, and then reduce the kernel code size.

With CONFIG_DMI (i.e before) :

   text    data     bss     dec     hex filename
1076076  128656   98304 1303036  13e1fc vmlinux

Without CONFIG_DMI (i.e after) :

   text    data     bss     dec     hex filename
1068092  126308   98304 1292704  13b9a0 vmlinux

Result:

   text    data     bss     dec     hex filename
  -7984   -2348       0  -10332   -285c vmlinux

The new option appears in "Processor type and features", only when
CONFIG_EMBEDDED is defined.

This patch is part of the Linux Tiny project, and is based on previous work
done by Matt Mackall <mpm@selenic.com>.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Anvin" <hpa@zytor.com>
Signed-off-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/acpi/thermal.c: fix build with CONFIG_DMI=n

drivers/acpi/thermal.c: In function 'acpi_thermal_init':
drivers/acpi/thermal.c:1794: error: 'thermal_dmi_table' undeclared (first use in this function)
drivers/acpi/thermal.c:1794: error: (Each undeclared identifier is reported only once
drivers/acpi/thermal.c:1794: error: for each function it appears in.)

Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

atmel_serial: remove duplicated macro definition

After commit 39d4c922b596633da86878b1a5cc881785b8e5fa (atmel_serial: fix
uart/console concurrent access) the UART_GET_TCR macro got redefined. This
patch removes the duplicated definition.

Signed-off-by: michael trimarchi <trimarchimichael@evidence.eu.com>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

serial: use time_before, time_before_eq, etc

The functions time_before, time_before_eq, time_after, and time_after_eq
are more robust for comparing jiffies against other values.

A simplified version of the semantic patch making this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@ change_compare_np @
expression E;
@@

(
- jiffies <= E
+ time_before_eq(jiffies,E)
|
- jiffies >= E
+ time_after_eq(jiffies,E)
|
- jiffies < E
+ time_before(jiffies,E)
|
- jiffies > E
+ time_after(jiffies,E)
)

@ include depends on change_compare_np @
@@

#include <linux/jiffies.h>

@ no_include depends on !include && change_compare_np @
@@

  #include <linux/...>
+ #include <linux/jiffies.h>
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

serial 8250: tighten test for using backup timer

Thomas Koeller had reported an issue where a device that had been making use
of the UART_BUG_TXEN code in the 8250 driver was mistakenly being caught by
the backup timer test, causing the device to work improperly.

To fix this, tighten the test requirements to enable the backup timer
workaround.

The backup timer is really meant to catch UARTs that don't re-assert the THRE
interrupt.  The expectation is that they do initially assert THRE.  This patch
clarifies the test.

Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Cc: Thomas Koeller <thomas@koeller.dyndns.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

serial: add VR41xx SIU setup for serial console

Add VR41xx SIU setup for serial console.

Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

serial: add vr41xx_siu_early_setup() for serial console

Add vr41xx_siu_early_setup() for serial console.

Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

uart_get_baud_rate: stop mangling termios

Russell King noticed this one: We have to avoid replacing B0 when we pick a
baud rate for a "hung up" port.  Ugly but the proper fix is in the tty layer
and means changing the tty<->serial interfaces so we will defer that for now.

[akpm@linux-foundation.org: fix uninitialised var]
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix tty speed handling on 8250

We try and write the correct speed back but the serial midlayer already
mangles the speed on us and that means if we request B0 we report back B9600
when we should not.  For now we'll hack around this in the drivers and serial
code, pending a better long term solution.

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>