igb: remove unneeded cleaned variable in clean_tx_irq path

The cleaned variable can be replaced by the count of packets cleaned during
the tx interrupt routine so it can be removed.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

e1000e: add support for new 82574L part

This new part has the same feature set as previous parts with the addition
of MSI-X support.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

e1000e: add support for 82567LM-3 and 82567LF-3 (ICH10D) parts

Add support for new LOM devices on the latest generation ICHx platforms.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

e1000e: add support for the 82567LM-4 device

Enable PCI device ID for a new combination of MAC and PHY already supported
in the driver.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

ixgbe: use different context for tso and offload

Change TSO offloads to use a different context than VLAN insertion
and Tx checksumming.  Hardware has separate registers internally for
storing these so use them.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

ixgbe: fix dca hints going to wrong processor

hardware was configured incorrectly which led all hints to be
sent to queue[0]'s DCA configuration.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

ixgbe: fix bug where lro settings are per ring

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

ixgbe: update dca to new interface, fix CONFIG_DCA_MODULE

DCA related fixes
=================
- ixgbe was not compiling and using DCA correctly if dca was a module
- DCA interface changed with new kernel
- ixgbe was not correctly configured to indicate DCA hints to the
  correct CPU.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

ixgbe: should not use HW_CSUM, should use IP* flags

as mentioned by Herbert, our hardware supports IP offloads, not full
checksum offloads for any protocol in existence (even though the
hardware just provides generic csum support over any range of bytes)

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

ixgbe: Lock RSS seed, move rx_buf_len to the rx_ring

This locks the seed down so loading/unloading the driver will present
predictable hashing from RSS.  Also move the rx_buf_len out of the adapter
struct, and into the Rx ring struct.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

ixgbe: Implement Tx Head Writeback

Enable Tx Head Writeback in the hardware.  This helps performance by
removing adapter writebacks to descriptors on transmit completion.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

ixgbe: disable flow control by default

Since the adapter cannot tell what the remote end's flow control capability
is through auto-neg, we must turn off flow control by default.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

ixgbe: Cleanup references to Tx and Rx rings to becommon across the driver

Cleanup all the different references to the Tx ring and Rx ring structures
and make them common across the driver.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

ixgbe: do not update stats twice each receive

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

ixgbe: Implement HAVE_SET_RX_MODE

Implement HAVE_SET_RX_MODE in the driver for MC and UC lists.

Signed-off-by: Christopher Leech <christopher.leech@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

ixgbe: add little endian annotations for sparse

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

ixgbe: fix rx csum return status misinterpretation

the driver was misinterpreting rx_csum return value in the descriptor
so occassionally we would indicate an rx_csum error in our stats
when there was none.  This would have no effect on traffic because
we would just hand the packet to the stack anyway without the offload
flag set, but would increase CPU for those packets that needed a recompute.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

ibm_newemac: MAL[12]_IER_EVENTS definition: 2x *_OTE -> *_DE

MAL[12]_IER_EVENTS definitions have MAL_IER_OTE twice
but lack MAL_IER_DE

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

hp-plus: fix link objects

Fix hp-plus Makefile object file:

drivers/built-in.o: In function `hpp_open':
hp-plus.c:(.text+0xaf445): undefined reference to `ei_interrupt'
hp-plus.c:(.text+0xaf4ac): undefined reference to `ei_open'
drivers/built-in.o: In function `hpp_close':
hp-plus.c:(.text+0xaf59d): undefined reference to `ei_close'
drivers/built-in.o: In function `hpp_probe1':
hp-plus.c:(.init.text+0x7314): undefined reference to `ei_poll'
drivers/built-in.o: In function `hp_plus_probe':
(.init.text+0x7407): undefined reference to `__alloc_ei_netdev'
make[1]: *** [.tmp_vmlinux1] Error 1

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

bonding: change some __constant_htons() to htons()

Resending since I didn't see any responses from the first try.

Change __constant_htons() to htons() in the bonding driver, it should
only be used for initializers.

-Brian

Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Rework efx_set_multicast_hash()

When !port_enabled, defer the write to reconfigure_mac_wrapper.

Whilst here, simplify the logic now that efx_start_port() always calls
efx_reconfigure_port().

From: Steve Hodgson <shodgson@solarflare.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Remove the STATE_RESETTING flag

This was originally a kludge to fix broken locking, which has since
been fixed properly.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Extend self-tests

Include PMA/PMD in loopback self-tests as intended.

Add NVRAM checksum validation and include it in self-tests.

Add register self-tests.

Run PHY self-tests where available.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Rework the bitfield header so that we can identify fields by bit number

This will support register self-tests.

From: Steve Hodgson <shodgson@solarflare.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Cleanup reset code

Move more code from efx_reset() into efx_reset_down() and efx_reset_up().

Stop propagating MAC/PHY setting failures from efx_reset_down() and
efx_reset_up() as these should not be fatal.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Remove some unreachable error paths

Some functions return an error code which is always 0.  Change their
return types to void and simplify their callers accordingly.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Remove remnants of multi-port abstraction for MAC registers

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Remove efx_nic_dummy_op_int() as redundant with efx_port_dummy_op_int()

Update comment on the dummy operation implementations.

Line up the board operation initialisers.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Enable TSO for 802.1q VLAN devices

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Do not call netif_{stop,wake}_queue() before register_netdev

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Make PHY flash mode a device attribute, not a module parameter

This allows updating PHY firmware for one interface without removing
all other interfaces handled by the driver.

Replace tx_disabled flags and 10Xpress status enumeration with flags in
enum efx_phy_mode.

Prevent an interface from being brought up while in PHY flash mode.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Implement get_sset_count, replacing get_stats_count and self_test_count

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Cleanup RX event processing

Make efx_process_channel() and falcon_process_eventq() return the
number of packets received rather than updating the quota, consistent
with new NAPI.

Since channels and RX queues are mapped one-to-one, remove return
value from falcon_handle_rx_event() and add a warning for events
with the wrong RX queue number.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Remove efx_channel::evqnum field

It is redundant with efx_channel::channel.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Make efx_for_each_channel_rx_queue() more efficient

Currently each channel can have at most one RX queue, so go straight to
that one.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Remove initialisation of RX_FILTER_CTL_REG.NUM_KER

We have long since given up doing RSS on Falcon A1 and therefore we
would always write the default value of 0.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Cleanup RX queue information

Rename efx_nic::rss_queues to the more obvious n_rx_queues

Remove efx_rx_queue::used and other stuff that's redundant with it.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Remove efx_channel::has_interrupt

efx_channel::has_interrupt is redundant with efx_channel::used_flags.

Remove efx_test_eventq() because it is now obviously unreachable.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Move CPU counting for RSS into a separate function, efx_wanted_rx_queues()

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Export boot configuration in EEPROM through ethtool

Extend the SPI device setup code to support this.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Removed forced inlining of long functions

gcc will automatically inline static functions with only one caller, and
may inline other functions depending on the kernel configuration and size
of the intermediate code.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Cleaned up struct tso_state fields

Squashed nested structures.

Renamed remaining_len to out_len, ifc.len to in_len, header_length to
header_len.

Moved ipv4_id into the group of output variables where it belongs.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Set net_device::vlan_features appropriately

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Use explicit bool for boolean variables, parameters and return values

Replace (cond ? 1 : 0) with cond or !!cond as appropriate, and
(cond ? 0 : 1) with !cond.

Remove some redundant boolean temporaries.

Rename one field that looks like a flag but isn't.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Reduce the size of struct efx_tx_buffer

Remove unmap_addr since it can be calculated from dma_addr, len and
unmap_len.  This saves 4-16 bytes.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Use pci_map_single() to map the skb header when doing TSO

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Don't leak PCI DMA maps in the TSO code when the queue fills up

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Speed up loopback self-test

Add efx_poll_loopback() function to test for successful completion of test.
Change efx_test_loopback() to end the test after 1 ms if
efx_poll_loopback() indicates success, and otherwise to wait for 100 ms
as before.

While we're here, rename efx_{rx,tx}_loopback() to
efx_{begin,end}_loopback() which more accurately reflect their
purpose.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Self-test reporting cleanup

Removed log messages that are redundant with calling functions.
Fixed bitwise or-ing of return codes.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Reduce log level for XGXS lane status

This was making noise during 10Xpress self-test.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Reverse the XOFF/XON pause frame control fifo thresholds

These were clearly bogus.

From: Steve Hodgson <shodgson@solarflare.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Remove inclusion of workarounds.h from efx.c

efx.c does not use hardware workarounds.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: XMAC statistics fix-ups

Exclude assumed size of RX control frames from rx_bad_bytes.

Exclude assumed size of TX control frames from tx_good_bytes for
consistency with rx_good_bytes.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Remove mistaken hardware workaround

We believed that some valid SNAP frames were being marked as invalid.
In fact this is not the case and no workaround is needed.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Reduce delays in SFE4001 initialisation

Currently the board initialisation includes 2 delays of 1 second each.
Usually it is unnecessary to wait that long, so check before doing so.

Correct some of the comments and log messages while we're here.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Avoid mangling error codes in efx_test_loopback()

efx_test_loopback() used "|" to combine the results of the RX and TX
phases.  If both phases fail with different error codes, this results
in a bogus error code.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Use separate hardware TX queues to select checksum generation

Checksum generation is an attribute of our hardware TX queues, not TX
descriptors.  We previously used a single queue and turned checksum
generation on or off as requested through ethtool.  However, this can
result in regenerating checksums in raw packets that should not be
modified.  We now create 2 hardware TX queues with checksum generation
on or off.  They are presented to the net core as one queue since it
does not know how to select between them.

The self-test verifies that a bad checksum is unaltered on the queue
with checksum generation off.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Remove unused field efx_channel::reset_work

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Change first parameter type of {set,clear}_bit_le() to unsigned

This means the compiler doesn't need to use real division instructions.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Replace net_dev->priv with netdev_priv(net_dev)

Use of the net_device::priv field is deprecated.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

netlink: Remove compat API for nested attributes

Removes all _nested_compat() functions from the API. The prio qdisc
no longer requires them and netem has its own format anyway. Their
existance is only confusing.

Resend: Also remove the wrapper macro.

Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'master' of /linux/kernel/git/davem/net-2.6

Conflicts:

net/mac80211/mlme.c

net: Unbreak userspace usage of linux/mroute.h

Nothing in linux/pim.h should be exported to userspace.

This should fix the XORP build failure reported by
Jose Calhariz, the debain package maintainer.

Nothing originally in linux/mroute.h was exported to userspace
ever, but some of this stuff started to be when it was moved into
this new linux/pim.h, and that was wrong.  If we didn't provide these
definitions for 10 years we can reasonably expect that applications
defined this stuff locally or used GLIBC headers providing the
protocol definitions.  And as such the only result of this can
be conflict and userland build breakage.

Signed-off-by: David S. Miller <davem@davemloft.net>

pkt_sched: Fix locking of qdisc_root with qdisc_root_sleeping_lock()

Use qdisc_root_sleeping_lock() instead of qdisc_root_lock() where
appropriate. The only difference is while dev is deactivated, when
currently we can use a sleeping qdisc with the lock of noop_qdisc.
This shouldn't be dangerous since after deactivation root lock could
be used only by gen_estimator code, but looks wrong anyway.

Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv6: When we droped a packet, we should return NET_RX_DROP instead of 0

Signed-off-by: Yang Hongyang <yanghy@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-next-2.6

b43: Rewrite TX power adjustment

This patch rewrites the TX power recalculation algorithms to scale better
with changed enviromnent. If there's low
TX traffic, the power will be checked against the desired values
every 60 seconds.
If there is high TX traffic, the check is redone every 2 seconds. This improves
the reaction times a lot and confuses the rate control less.
It will also reduce the time it initially takes to tune to a new TX power
value. With the old algorithm it could take about 30 to 45 seconds to settle to
a new power value. This will happen in about two to four seconds now.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: Implement dynamic PHY API

This patch implements a dynamic "ops" based PHY API.
This is needed in order to conveniently support future PHY types
to avoid the "switch"-hell.

This patch does not change any functionality. It just moves lots
of code from one place to another and adjusts it for the changed
data structures.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Release rt2x00 2.2.1

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: skb->data pointer should not include TX descriptor

Make sure the skb->data pointer points to the frame data, not the TX
descriptor. The frame dumping code relies on that.

Signed-off-by: Mattias Nissler <mattias.nissler@gmx.de>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Add Signal type flag

Instead of using the PLCP flag to indicate if the
signal value is plcp or the bitrate we should add
a new flag to mark the bitrate type explicitely.
This is usefull when new types are added later for
rt2800.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Initialize txop during conf_tx() callback

The txop parameter is supported by rt61pci and rt73usb,
and thus should be written to the register instead
of using the fixed value set during initialization.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Only configure hardware when radio is enabled

Some hardware configuration registers such as antenna and channel configuration
can only be written when the radio is enabled. Previously, we didn't consider
this, so some configuration items could be set inconsistently after reenabling
the radio. This patch changes the config() handler to only reprogram the
hardware when the radio is enabled. Configuration changes that are made while
the radio is off are postponed until the radio is switched back on. We also
leave the radio turned off during initialization and only enable it when
requested by mac80211. This allows us to get rid of the DIRTY_CONFIG flag,
because the device is now guaranteed to be completely initialized when brought
up by mac80211.

Signed-off-by: Mattias Nissler <mattias.nissler@gmx.de>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Map extra_tx_headroom to DMA

If a driver requests additional headroom it should
be mapped to DMA as well because it will be send to
the hardware as well (as form of extra descriptor).

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Fix race conditions in flag handling

Some of the flags should be accessed atomically to
prevent race conditions. The flags that are most important
are those that can change often and indicate the actual
state of the device, queue or queue entry.

The big flag rename was done to move all state flags to
the same naming type as the other rt2x00dev flags and
made sure all places where the flags were used were changed. ;)

Thanks to Stephen for most of the queue flags updates,
which fixes some of the most obvious consequences of the
race conditions. Among those the notorious:

rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 0.
rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 0.
rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 0.

Signed-off-by: Stephen Blackheath <tramp.enshrine.stephen@blacksapphire.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: use the common frame control functions

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rfkill: rename rfkill_mutex to rfkill_global_mutex

rfkill_mutex and rfkill->mutex are too easy to confuse with each other.

Rename rfkill_mutex to rfkill_global_mutex, so that they are easier to tell
apart with just one glance.

Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rfkill: add WARN and BUG_ON paranoia (v2)

BUG_ON() and WARN() the heck out of buggy drivers calling into the rfkill
subsystem.

Also switch from WARN_ON(1) to the new descriptive WARN().

Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rfkill: add missing line break

Trivial patch adding a missing line break on
rfkill_claim_show().

Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: Ivo van Doorn <IvDoorn@gmail.co>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rfkill: use strict_strtoul (v2)

Switch sysfs parsing to something that actually works properly.

Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: rc.h cleanup

Use kernel doc syntax for comments and remove a few unused macros.

Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Remove sc_lastrx as we don't use it anywhere

Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Do not update frame's duration field

When AR_DurUpdateEna is set, the frame's duration field
is updated by the MAC based on the current rate.

Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Remove more dead code

Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Add LED support

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211/cfg80211: HT capabilities for NEW_STA

Allow userspace (e.g., hostapd) to set HT capabilities for associated
STAs. This is based on a patch from Zhu Yi <yi.zhu@intel.com> (only
the NL80211_ATTR_HT_CAPABILITY for NEW_STA part is included here).

Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

p54pci: rx tasklet refactoring

This patch moves the all of p54pci's receiver code out of the
bloated interrupt handler routine and into a less critical tasklet.

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

p54: redo queue numbering

The firmware supports 8 different queues and not only 4.
So, let's make some room for further tasks (ap/adhoc support)
in this area.

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

p54: take tx_queue's lock in rx_frame_sent

p54_rx_frame_sent will alter the tx_queue. Therefore we should hold
the lock to protect against concurrent p54_assign_address calls.

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

p54: fix rssi auto calibration

Ever wondered why the signal was so bad with p54 compared to madwifi, or intel?

Well, if you have revision 1 rssi calibration curve points in your EEPROM, then wonder no more.
The firmware wants a extra 1 byte padding for every curve point. But someone forgot to put
them into the EEPROM's data structure...

So now, big question: what happens when we blindly "memcpy" these data points?

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wireless: remove unused #include <version.h>

The driver(s) below do not use LINUX_VERSION_CODE nor KERNEL_VERSION.
  drivers/net/wireless/b43legacy/main.c
  drivers/net/wireless/iwlwifi/iwl-3945-led.c
  drivers/net/wireless/iwlwifi/iwl-led.c
  drivers/net/wireless/iwlwifi/iwl-rfkill.c

This patch removes the said #include <version.h>.

Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Use mac80211 for multicast power save buffering

Replace the internal ath9k implementation of multicast/broadcast frame
power save buffering (AP mode) in ath9k with use of mac80211
ieee80211_get_buffered_bc() mechanism. This removes quite a bit of
duplicated functionality and simplifies the driver part.

Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211_hwsim: Add minimal IEEE 802.11n support

Set some semi-random values for HT and add more queues to allow IEEE
802.11n association to be tested with mac80211_hwsim. This with the
latest hostapd git tree version can complete a simulated 802.11n
association successfully (with mac80211 client MLME).

Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ssb: Clean up extraction of MAC addresses from SPROM

Only rev 1 and 2 ssb SPROMs have fields named et0mac and et1mac;
however, all of the extraction routines extract pseudo data for these
fields from regions that are all 1's resulting in a hardware address
of FF:FF:FF:FF:FF:FF. This patch forces such a fill at the beginning of
the data extraction process, and only does the formal extraction if the
SPROM rev is 1 or 2.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: convert adhoc operations to direct commands

with fixes for v9 and later firmware too.

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: convert CMD_802_11_RADIO_CONTROL to a direct command

and return errors for operations like join & scan that aren't possible
when the radio is turned off.

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: convert CMD_802_11_DEAUTHENTICATE to a direct command

and remove DISASSOCIATE because it's not in any of the specs and has
never been used.

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: convert CMD_802_11_RF_TX_POWER to a direct command

And while we're at it, grab min/max TX power from the firmware and use
that to validate incoming TX power requests from WEXT.

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ssb: Update for Rev. 5 SPROM

Although a revision 5 SPROM has not been seen in the wild, the
open-source portion of the MIPS driver 4.150.10.5 describes its
layout, which is mostly inherited from revision 4. This patch
implements the differences.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: Use only precedence level of DSCP field for frame classification

Bit 4-5 of DSCP should not be considered by classify_d1. The
802.11 QoS Priority field is only depending on the precedence level.

Signed-off-by: Daniel Wagner <wagi@monom.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>