cxgb4: configure HW VLAN extraction through FW

HW VLAN extraction needs to be configured through FW to work correctly in
virtualization environments.  Remove the direct register manipulation and
rely on FW.

Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000e: add PCI device id to enable support for 82567V-4

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000e: Fix/cleanup PHY reset code for ICHx/PCHx

i) Fixes a bug where e1000_sw_lcd_config_ich8lan() was calling
e1000_lan_init_done_ich8lan() to poll the STATUS.LAN_INIT_DONE bit to
make sure the MAC had completed the PHY configuration.  However,
e1000_lan_init_done_ich8lan() had already been called in one of the two
places where PHY reset occurs for ICHx/PCHx parts, which caused the second
call to busy-wait for 150 msec because the LAN_INIT_DONE bit had already
been checked and cleared.

ii) Cleanup the two separate PHY reset code paths, i.e. the full-chip reset
in e1000_reset_hw_ich8lan() and the PHY-only reset in
e1000_phy_hw_reset_ich8lan().  There was duplicate code in both paths to be
performed post-reset that are now combined into one new function -
e1000_post_phy_reset_ich8lan().  This cleanup also included moving the
clearing of the PHY Reset Asserted bit in the STATUS register (now done for
all ICH/PCH parts) and the check for the indication from h/w that basic
configuration has completed back to where it previously was in
e1000_get_cfg_done_ich8lan().

iii) Corrected a few comments

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000e: move settting of flow control refresh timer to link setup code

The flow control refresh timer value needs to be saved off so that it can
be programmed into the approrpiate register when applicable but without a
reset, e.g. when changing flow control parameters via ethtool.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000e: fix checks for manageability enabled and management pass-through

The mac->arc_subsystem was being incorrectly used to flag whether or not
manageability was enabled when it should only be used to state whether the
ARC (Host interface) subsystem is available on a particular MAC _and_ only
valid when any manageability is enabled. The ARC subsystem is currently
only available on 80003es2lan and 82573 parts supported by the driver.

A new flag, has_fwsm, is introduced to be used when checking if
manageability is enabled but only on parts that acutally have an FWSM
register. While the above parts have an FWSM register, there are other
parts that have FWSM but do not have support for the ARC subsystem,
namely 82571/2 and ICHx/PCH.

And then there are parts that have manageability, but do not have either
FWSM register or support for the ARC subsystem - these are 82574 and 82583.

For 80003es2lan, 82571/2/3 and ICH/PCH parts, this patch makes no
functional changes, it only corrects the usage of the manageability flags.
For 82574 and 82583, it fixes the incorrect accesses of the non-existent
FWSM register and ARC subsystem as well as corrects the check for
management pass-through.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000e: Incorrect function pointer set for force_speed_duplex on 82577

The force_speed_duplex function pointer was incorrectly set.  Instead of
calling the 82577-specific version it was calling the m88 version which,
among other incorrect things, reset the PHY causing autonegotiation to be
re-enabled in the PHY resulting in the link defaulting to half-duplex.
The 82577-specific force_speed_duplex function also had an issue where
it disabled Auto-MDI-X which caused the link to not come up.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000e: Cleanup e1000_sw_lcd_config_ich8lan()

After every reset all ICH/PCH parts call this function which acquires the
swflag, performs a workaround on applicable parts and releases the swflag.
There is no reason for parts for which this workaround is not applicable
to acquire and release the swflag so the function should just return
without doing anything for these parts.  This also provides for the
indentation of most of the function contents to be shifted left cleaning up
the code.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000e: Remove EN_MAC_ADDR_FILTER check from enable_mng_pass_thru check

Patch addresses issues when manageability passthrough is enabled, but the
MAC_ADDR_FILTER bit is not set in the MANC register.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000e: cleanup multiple common exit points

...in e1000_update_nvm_checksum_ich8lan().

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000e: s/w initiated LSC MSI-X interrupts not generated; no transmit

In MSI-X mode when an IMPI SoL session was active (i.e. the PHY reset was
blocked), the LSC interrupt generated by s/w to start the watchdog which
started the transmitter was not getting fired by the hardware because bit
24 (the 'other' cause bit) also needed to be set.  Without an active SoL
session, the PHY was reset which caused the h/w to fire the LSC interrupt.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000e: initialize manageability (IPMI) pass-through in 82574/82583

82574/82583 uses different registers/bits to setup manageability filters
than all other parts supported by e1000e; set them accordingly for IPMI
pass-through.  Rename the function to better reflect what it does.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000e: bad state after running ethtool diagnostics with AMT enabled

When running ethtool online diagnostics with no open interface, there is a
short period of time where the driver relinquishes control of the adapter
during which time AMT (manageability firmware) can put the adapter into an
unknown state resulting in such things as link test failure, hardware hang,
reporting an incorrect link speed, etc.  Resetting the adapter during an
open() resolves this by putting the adapter into a quiescent state.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000e: use static params to save stack space (part 2)

A couple stack cleanups missed in an earlier patch from Jesse.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'master' of git://git./linux/kernel/git/kaber/ipmr-2.6

netxen: handle queue manager access

Check the access by tools for hardware queue engine and handle it
separately than other block registers, otherwise incorrect data
is returned.

Support for only NX3031 based cards.

Acked-by: Dhananjay Phadke <dhananjay.phadke@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

netxen: to fix onchip memory access.

Remove unnecessary remap of the region in bar 0 to access onhip memory
for NX3031.

Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

netxen: remove unnecessary size checks

NX3031 have 64bit on card memory. Fix the limit check to
64MB and remove unnecessary 128bit read/write check.

Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

netxen: fix register usage

o For NX3031, MSI_MODE, CAPABILITIES_FW and SCRATCHPAD registers
  are obsolete. These register addresses can be used for different
  purpose.

Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: Reduce footprint by un-inlining tipc_msg_* routines

Convert tipc_msg_* inline routines that are more than one line into
standard functions, thereby eliminating some repeated code.

Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: Reduce footprint by un-inlining buf_acquire routine

Convert buf_acquire inline routine that is more than one line into
a standard function, thereby eliminating some repeated code.

Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: Reduce footprint by un-inlining bearer congestion routine

Convert bearer congestion inline routine that is more than one line into
a standard function, thereby eliminating some repeated code.

Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: Reduce footprint by un-inlining port list routines

Converts port list inline routines that are more than one line into
standard functions, thereby eliminating a significant amount of
repeated code.

Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: Reduce footprint by un-inlining nmap routines

Converts nmap inline routines that are more than one line into standard
functions, thereby eliminating a significant amount of repeated code.

Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: Reduce footprint by un-inlining address routines

Convert address-related inline routines that are more than one
line into standard functions, thereby eliminating a significant
amount of repeated code.

Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: add tipc_ prefix to fcns targeted for un-inlining

These functions have enough code in them such that they
seem like sensible targets for un-inlining.  Prior to doing
that, this adds the tipc_ prefix to the functions, so that
in the event of a panic dump or similar, the subsystem from
which the functions come from is immediately clear.

Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: Relocate trivial link status functions to header file

Rather than live in link.c where they can only be used in that file alone,
these helper routines are better served by being in link.h

Relocated are the following:

link_working_working
link_working_unknown
link_reset_unknown
link_reset_reset
link_blocked
link_congested

Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: remove abstraction for link_max_pkt

This is just a straight return of a field; there is no
value in the abstraction of hiding it behind a function.

Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: Update commenting in TIPC API

Eliminate comments in TIPC's main API files that are either obsolete,
incorrect, misleading, or unhelpful.  It also adds in one new comment.

Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: Add support for "-s" configuration option

Provide initial support for displaying overall TIPC status/statistics
information at runtime.  Currently, only version info for the TIPC
kernel module is displayed.

Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: Rename "multicast-link" to "broadcast-link"

Make a cosmetic change to the name displayed for the broadcast link,
to better reflect its true nature. Since TIPC utilizes this link to
distribute name table information, in addition to multicast messages
sent by user applications, the prior name "multicast-link" is
no longer appropriate.

Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: Eliminate unnecessary initialization in native API send routines

Eliminate a couple of instances where TIPC's native API send routines
were doing pointless initialization of local variables.

Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: Prune unused data structures from configuration service

Eliminate some unused data structures in the TIPC
configuration service that relate to the handling of link
subscriptions, which were not supported when TIPC 1.5 was
introduced.  If and when support for link subscriptions is
offered in TIPC, these elements may need to be re-introduced.

Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: Eliminate unused argument in print statement

Eliminate an argument in a print statement that has no corresponding
format specification.

Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: Eliminate obsolete port's "congested_link" field

Eliminate a field of the TIPC port structure that is populated,
but never referenced.

Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

netfilter: xtables: add missing depends for xt_TEE

Aviod these link-time errors when IPV6=m, XT_TEE=y:

net/built-in.o: In function `tee_tg_route6':
xt_TEE.c:(.text+0x45ca5): undefined reference to `ip6_route_output'
net/built-in.o: In function `tee_tg6':
xt_TEE.c:(.text+0x45d79): undefined reference to `ip6_local_out'

Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'master' of /linux/kernel/git/davem/net-2.6

Conflicts:
Documentation/feature-removal-schedule.txt
drivers/net/wireless/ath/ar9170/usb.c
drivers/scsi/iscsi_tcp.c
net/ipv4/ipmr.c

Merge branch 'hwmon-for-linus' of git://git./linux/kernel/git/jdelvare/staging

* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
  hwmon: (applesmc) Correct sysfs fan error handling
  hwmon: (asc7621) Bug fixes

Merge branch 'perf-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip

* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  kprobes/x86: Fix removed int3 checking order
  perf: Fix static strings treated like dynamic ones

drivers/gpu/drm/i915/i915_irq.c:i915_error_object_create(): use correct kmap-atomic slot

i915_error_object_create() is called from the timer interrupt and hence
can corrupt the KM_USER0 slot.  Use KM_IRQ0 instead.

Reported-by: Jaswinder Singh Rajput <jaswinderlinux@gmail.com>
Tested-by: Jaswinder Singh Rajput <jaswinderlinux@gmail.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

hp_accel: fix race in device removal

The work queue has to be flushed after the device has been made
inaccessible.  The patch closes a window during which a work queue might
remain active after the device is removed and would then lead to ACPI
calls with undefined behavior.

Signed-off-by: Oliver Neukum <oneukum@suse.de>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Pavel Herrmann <morpheus.ibis@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mqueue: fix kernel BUG caused by double free() on mq_open()

In case of aborting because we reach the maximum amount of memory which
can be allocated to message queues per user (RLIMIT_MSGQUEUE), we would
try to free the message area twice when bailing out: first by the error
handling code itself, and then later when cleaning up the inode through
delete_inode().

Signed-off-by: André Goddard Rosa <andre.goddard@gmail.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fbdev: bfin-t350mcqb-fb: fix fbmem allocation with blanking lines

The current allocation does not include the memory required for blanking
lines.  So avoid memory corruption when multiple devices are using the DMA
memory near each other.

Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

memcg: fix css_is_ancestor() RCU locking

Some callers (in memcontrol.c) calls css_is_ancestor() without
rcu_read_lock.  Because css_is_ancestor() has to access RCU protected
data, it should be under rcu_read_lock().

This makes css_is_ancestor() itself does safe access to RCU protected
area.  (At least, "root" can have refcnt==0 if it's not an ancestor of
"child".  So, we need rcu_read_lock().)

Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Cc: Balbir Singh <balbir@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

memcg: fix css_id() RCU locking for real

Commit ad4ba375373937817404fd92239ef4cadbded23b ("memcg: css_id() must be
called under rcu_read_lock()") modifies memcontol.c for fixing RCU check
message.  But Andrew Morton pointed out that the fix doesn't seems sane
and it was just for hidining lockdep messages.

This is a patch for do proper things.  Checking again, all places,
accessing without rcu_read_lock, that commit fixies was intentional....
all callers of css_id() has reference count on it.  So, it's not necessary
to be under rcu_read_lock().

Considering again, we can use rcu_dereference_check for css_id().  We know
css->id is valid if css->refcnt > 0.  (css->id never changes and freed
after css->refcnt going to be 0.)

This patch makes use of rcu_dereference_check() in css_id/depth and remove
unnecessary rcu-read-lock added by the commit.

Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Cc: Balbir Singh <balbir@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

bsdacct: use del_timer_sync() in acct_exit_ns()

acct_exit_ns --> acct_file_reopen deletes timer without check timer
execution on other CPUs.  So acct_timeout() can change an unmapped memory.

Signed-off-by: Vitaliy Gusev <vgusev@openvz.org>
Cc: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rmap: remove anon_vma check in page_address_in_vma()

Currently page_address_in_vma() compares vma->anon_vma and
page_anon_vma(page) for parameter check, but in 2.6.34 a vma can have
multiple anon_vmas with anon_vma_chain, so current check does not work.
(For anonymous page shared by multiple processes, some verified (page,vma)
pairs return -EFAULT wrongly.)

We can go to checking all anon_vmas in the "same_vma" chain, but it needs
to meet lock requirement.  Instead, we can remove anon_vma check safely
because page_address_in_vma() assumes that page and vma are already
checked to belong to the identical process.

Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Reviewed-by: Rik van Riel <riel@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

hugetlbfs: kill applications that use MAP_NORESERVE with SIGBUS instead of OOM-killer

Ordinarily, application using hugetlbfs will create mappings with
reserves.  For shared mappings, these pages are reserved before mmap()
returns success and for private mappings, the caller process is guaranteed
and a child process that cannot get the pages gets killed with sigbus.

An application that uses MAP_NORESERVE gets no reservations and mmap()
will always succeed at the risk the page will not be available at fault
time.  This might be used for example on very large sparse mappings where
the developer is confident the necessary huge pages exist to satisfy all
faults even though the whole mapping cannot be backed by huge pages.
Unfortunately, if an allocation does fail, VM_FAULT_OOM is returned to the
fault handler which proceeds to trigger the OOM-killer.  This is
unhelpful.

Even without hugetlbfs mounted, a user using mmap() can trivially trigger
the OOM-killer because VM_FAULT_OOM is returned (will provide example
program if desired - it's a whopping 24 lines long).  It could be
considered a DOS available to an unprivileged user.

This patch alters hugetlbfs to kill a process that uses MAP_NORESERVE
where huge pages were not available with SIGBUS instead of triggering the
OOM killer.

This change affects hugetlb_cow() as well.  I feel there is a failure case
in there, but I didn't create one.  It would need a fairly specific target
in terms of the faulting application and the hugepage pool size.  The
hugetlb_no_page() path is much easier to hit but both might as well be
closed.

Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Cc: Lee Schermerhorn <lee.schermerhorn@hp.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kexec: fix OOPS in crash_kernel_shrink

Two "echo 0 > /sys/kernel/kexec_crash_size" OOPSes kernel.  Also content
of this file is invalid after first shrink to zero: it shows 1 instead of
0.

This scenario is unlikely to happen often (root privs, valid crashkernel=
in cmdline, dump-capture kernel not loaded), I hit it only by chance.

This patch fixes it.

Signed-off-by: Vitaly Mayatskikh <v.mayatskih@gmail.com>
Cc: Cong Wang <amwang@redhat.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mmc: atmel-mci: fix in debugfs: response value printing

In debugfs, printing of command response reports resp[2] twice: fix it to
resp[3].

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mmc: atmel-mci: remove data error interrupt after xfer

Disable data error interrupts while we are actually recording that there
is not such errors.  This will prevent, in some cases, the warning message
printed at new request queuing (in atmci_start_request()).

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: <linux-mmc@vger.kernel.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mmc: atmel-mci: prevent kernel oops while removing card

The removing of an SD card in certain circumstances can lead to a kernel
oops if we do not make sure that the "data" field of the host structure is
valid.  This patch adds a test in atmci_dma_cleanup() function and also
calls atmci_stop_dma() before throwing away the reference to data.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: <linux-mmc@vger.kernel.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mmc: atmel-mci: fix two parameters swapped

Two parameters were swapped in the calls to atmci_init_slot().

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Reported-by: Anders Grahn <anders.grahn@hd-wireless.se>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: <linux-mmc@vger.kernel.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

revert "procfs: provide stack information for threads" and its fixup commits

Originally, commit d899bf7b ("procfs: provide stack information for
threads") attempted to introduce a new feature for showing where the
threadstack was located and how many pages are being utilized by the
stack.

Commit c44972f1 ("procfs: disable per-task stack usage on NOMMU") was
applied to fix the NO_MMU case.

Commit 89240ba0 ("x86, fs: Fix x86 procfs stack information for threads on
64-bit") was applied to fix a bug in ia32 executables being loaded.

Commit 9ebd4eba7 ("procfs: fix /proc/<pid>/stat stack pointer for kernel
threads") was applied to fix a bug which had kernel threads printing a
userland stack address.

Commit 1306d603f ('proc: partially revert "procfs: provide stack
information for threads"') was then applied to revert the stack pages
being used to solve a significant performance regression.

This patch nearly undoes the effect of all these patches.

The reason for reverting these is it provides an unusable value in
field 28.  For x86_64, a fork will result in the task->stack_start
value being updated to the current user top of stack and not the stack
start address.  This unpredictability of the stack_start value makes
it worthless.  That includes the intended use of showing how much stack
space a thread has.

Other architectures will get different values.  As an example, ia64
gets 0.  The do_fork() and copy_process() functions appear to treat the
stack_start and stack_size parameters as architecture specific.

I only partially reverted c44972f1 ("procfs: disable per-task stack usage
on NOMMU") .  If I had completely reverted it, I would have had to change
mm/Makefile only build pagewalk.o when CONFIG_PROC_PAGE_MONITOR is
configured.  Since I could not test the builds without significant effort,
I decided to not change mm/Makefile.

I only partially reverted 89240ba0 ("x86, fs: Fix x86 procfs stack
information for threads on 64-bit") .  I left the KSTK_ESP() change in
place as that seemed worthwhile.

Signed-off-by: Robin Holt <holt@sgi.com>
Cc: Stefani Seibold <stefani@seibold.net>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

it8761e_gpio: fix bug in gpio numbering

The SIO chip contains 16 possible gpio lines, not 14.  The schematic was
not read carefully.

Signed-off-by: Denis Turischev <denis@compulab.co.il>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

dma-mapping: fix dma_sync_single_range_*

dma_sync_single_range_for_cpu() and dma_sync_single_range_for_device() use
a wrong address with a partial synchronization.

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ar9170: fix for driver-core ABI change

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-next-2.6 into for-davem

Conflicts:
drivers/net/wireless/ath/ar9170/main.c

Merge branch 'drm-linus' of git://git./linux/kernel/git/airlied/drm-2.6

* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
  drm/radeon: Fix 3 regressions - since buffer rework

Merge git://git./linux/kernel/git/davem/net-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  net: Fix FDDI and TR config checks in ipv4 arp and LLC.
  IPv4: unresolved multicast route cleanup
  mac80211: remove association work when processing deauth request
  ar9170: wait for asynchronous firmware loading
  ipv4: udp: fix short packet and bad checksum logging
  phy: Fix initialization in micrel driver.
  sctp: Fix a race between ICMP protocol unreachable and connect()
  veth: Dont kfree_skb() after dev_forward_skb()
  IPv6: fix IPV6_RECVERR handling of locally-generated errors
  net/gianfar: drop recycled skbs on MTU change
  iwlwifi: work around passive scan issue

CacheFiles: Fix occasional EIO on call to vfs_unlink()

Fix an occasional EIO returned by a call to vfs_unlink():

[ 4868.465413] CacheFiles: I/O Error: Unlink failed
[ 4868.465444] FS-Cache: Cache cachefiles stopped due to I/O error
[ 4947.320011] CacheFiles: File cache on md3 unregistering
[ 4947.320041] FS-Cache: Withdrawing cache "mycache"
[ 5127.348683] FS-Cache: Cache "mycache" added (type cachefiles)
[ 5127.348716] CacheFiles: File cache on md3 registered
[ 7076.871081] CacheFiles: I/O Error: Unlink failed
[ 7076.871130] FS-Cache: Cache cachefiles stopped due to I/O error
[ 7116.780891] CacheFiles: File cache on md3 unregistering
[ 7116.780937] FS-Cache: Withdrawing cache "mycache"
[ 7296.813394] FS-Cache: Cache "mycache" added (type cachefiles)
[ 7296.813432] CacheFiles: File cache on md3 registered

What happens is this:

 (1) A cached NFS file is seen to have become out of date, so NFS retires the
     object and immediately acquires a new object with the same key.

 (2) Retirement of the old object is done asynchronously - so the lookup/create
     to generate the new object may be done first.

     This can be a problem as the old object and the new object must exist at
     the same point in the backing filesystem (i.e. they must have the same
     pathname).

 (3) The lookup for the new object sees that a backing file already exists,
     checks to see whether it is valid and sees that it isn't.  It then deletes
     that file and creates a new one on disk.

 (4) The retirement phase for the old file is then performed.  It tries to
     delete the dentry it has, but ext4_unlink() returns -EIO because the inode
     attached to that dentry no longer matches the inode number associated with
     the filename in the parent directory.

The trace below shows this quite well.

[md5sum] ==> __fscache_relinquish_cookie(ffff88002d12fb58{NFS.fh,ffff88002ce62100},1)
[md5sum] ==> __fscache_acquire_cookie({NFS.server},{NFS.fh},ffff88002ce62100)

NFS has retired the old cookie and asked for a new one.

[kslowd] ==> fscache_object_state_machine({OBJ52,OBJECT_ACTIVE,24})
[kslowd] <== fscache_object_state_machine() [->OBJECT_DYING]
[kslowd] ==> fscache_object_state_machine({OBJ53,OBJECT_INIT,0})
[kslowd] <== fscache_object_state_machine() [->OBJECT_LOOKING_UP]
[kslowd] ==> fscache_object_state_machine({OBJ52,OBJECT_DYING,24})
[kslowd] <== fscache_object_state_machine() [->OBJECT_RECYCLING]

The old object (OBJ52) is going through the terminal states to get rid of it,
whilst the new object - (OBJ53) - is coming into being.

[kslowd] ==> fscache_object_state_machine({OBJ53,OBJECT_LOOKING_UP,0})
[kslowd] ==> cachefiles_walk_to_object({ffff88003029d8b8},OBJ53,@68,)
[kslowd] lookup '@68'
[kslowd] next -> ffff88002ce41bd0 positive
[kslowd] advance
[kslowd] lookup 'Es0g00og0_Nd_XCYe3BOzvXrsBLMlN6aw16M1htaA'
[kslowd] next -> ffff8800369faac8 positive

The new object has looked up the subdir in which the file would be in (getting
dentry ffff88002ce41bd0) and then looked up the file itself (getting dentry
ffff8800369faac8).

[kslowd] validate 'Es0g00og0_Nd_XCYe3BOzvXrsBLMlN6aw16M1htaA'
[kslowd] ==> cachefiles_bury_object(,'@68','Es0g00og0_Nd_XCYe3BOzvXrsBLMlN6aw16M1htaA')
[kslowd] remove ffff8800369faac8 from ffff88002ce41bd0
[kslowd] unlink stale object
[kslowd] <== cachefiles_bury_object() = 0

It then checks the file's xattrs to see if it's valid.  NFS says that the
auxiliary data indicate the file is out of date (obvious to us - that's why NFS
ditched the old version and got a new one).  CacheFiles then deletes the old
file (dentry ffff8800369faac8).

[kslowd] redo lookup
[kslowd] lookup 'Es0g00og0_Nd_XCYe3BOzvXrsBLMlN6aw16M1htaA'
[kslowd] next -> ffff88002cd94288 negative
[kslowd] create -> ffff88002cd94288{ffff88002cdaf238{ino=148247}}

CacheFiles then redoes the lookup and gets a negative result in a new dentry
(ffff88002cd94288) which it then creates a file for.

[kslowd] ==> cachefiles_mark_object_active(,OBJ53)
[kslowd] <== cachefiles_mark_object_active() = 0
[kslowd] === OBTAINED_OBJECT ===
[kslowd] <== cachefiles_walk_to_object() = 0 [148247]
[kslowd] <== fscache_object_state_machine() [->OBJECT_AVAILABLE]

The new object is then marked active and the state machine moves to the
available state - at which point NFS can start filling the object.

[kslowd] ==> fscache_object_state_machine({OBJ52,OBJECT_RECYCLING,20})
[kslowd] ==> fscache_release_object()
[kslowd] ==> cachefiles_drop_object({OBJ52,2})
[kslowd] ==> cachefiles_delete_object(,OBJ52{ffff8800369faac8})

The old object, meanwhile, goes on with being retired.  If allocation occurs
first, cachefiles_delete_object() has to wait for dir->d_inode->i_mutex to
become available before it can continue.

[kslowd] ==> cachefiles_bury_object(,'@68','Es0g00og0_Nd_XCYe3BOzvXrsBLMlN6aw16M1htaA')
[kslowd] remove ffff8800369faac8 from ffff88002ce41bd0
[kslowd] unlink stale object
EXT4-fs warning (device sda6): ext4_unlink: Inode number mismatch in unlink (148247!=148193)
CacheFiles: I/O Error: Unlink failed
FS-Cache: Cache cachefiles stopped due to I/O error

CacheFiles then tries to delete the file for the old object, but the dentry it
has (ffff8800369faac8) no longer points to a valid inode for that directory
entry, and so ext4_unlink() returns -EIO when de->inode does not match i_ino.

[kslowd] <== cachefiles_bury_object() = -5
[kslowd] <== cachefiles_delete_object() = -5
[kslowd] <== fscache_object_state_machine() [->OBJECT_DEAD]
[kslowd] ==> fscache_object_state_machine({OBJ53,OBJECT_AVAILABLE,0})
[kslowd] <== fscache_object_state_machine() [->OBJECT_ACTIVE]

(Note that the above trace includes extra information beyond that produced by
the upstream code).

The fix is to note when an object that is being retired has had its object
deleted preemptively by a replacement object that is being created, and to
skip the second removal attempt in such a case.

Reported-by: Greg M <gregm@servu.net.au>
Reported-by: Mark Moseley <moseleymark@gmail.com>
Reported-by: Romain DEGEZ <romain.degez@smartjog.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ACPI: sleep: eliminate duplicate entries in acpisleep_dmi_table[]

Duplicate entries ended up acpisleep_dmi_table[] by accident.
They don't hurt functionality, but they are ugly, so let's get
rid of them.

Cc: stable@kernel.org
Signed-off-by: Alex Chiang <achiang@canonical.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ipv6: ip6mr: add support for dumping routing tables over netlink

The ip6mr /proc interface (ip6_mr_cache) can't be extended to dump routes
from any tables but the main table in a backwards compatible fashion since
the output format ends in a variable amount of output interfaces.

Introduce a new netlink interface to dump multicast routes from all tables,
similar to the netlink interface for regular routes.

Signed-off-by: Patrick McHardy <kaber@trash.net>

ipv6: ip6mr: support multiple tables

This patch adds support for multiple independant multicast routing instances,
named "tables".

Userspace multicast routing daemons can bind to a specific table instance by
issuing a setsockopt call using a new option MRT6_TABLE. The table number is
stored in the raw socket data and affects all following ip6mr setsockopt(),
getsockopt() and ioctl() calls. By default, a single table (RT6_TABLE_DFLT)
is created with a default routing rule pointing to it. Newly created pim6reg
devices have the table number appended ("pim6regX"), with the exception of
devices created in the default table, which are named just "pim6reg" for
compatibility reasons.

Packets are directed to a specific table instance using routing rules,
similar to how regular routing rules work. Currently iif, oif and mark
are supported as keys, source and destination addresses could be supported
additionally.

Example usage:

- bind pimd/xorp/... to a specific table:

uint32_t table = 123;
setsockopt(fd, SOL_IPV6, MRT6_TABLE, &table, sizeof(table));

- create routing rules directing packets to the new table:

# ip -6 mrule add iif eth0 lookup 123
# ip -6 mrule add oif eth0 lookup 123

Signed-off-by: Patrick McHardy <kaber@trash.net>

ipv6: ip6mr: move mroute data into seperate structure

Signed-off-by: Patrick McHardy <kaber@trash.net>

ipv6: ip6mr: convert struct mfc_cache to struct list_head

Signed-off-by: Patrick McHardy <kaber@trash.net>

ipv6: ip6mr: remove net pointer from struct mfc6_cache

Now that cache entries in unres_queue don't need to be distinguished by their
network namespace pointer anymore, we can remove it from struct mfc6_cache
add pass the namespace as function argument to the functions that need it.

Signed-off-by: Patrick McHardy <kaber@trash.net>

ipv6: ip6mr: move unres_queue and timer to per-namespace data

The unres_queue is currently shared between all namespaces. Following patches
will additionally allow to create multiple multicast routing tables in each
namespace. Having a single shared queue for all these users seems to excessive,
move the queue and the cleanup timer to the per-namespace data to unshare it.

As a side-effect, this fixes a bug in the seq file iteration functions: the
first entry returned is always from the current namespace, entries returned
after that may belong to any namespace.

Signed-off-by: Patrick McHardy <kaber@trash.net>

hwmon: (applesmc) Correct sysfs fan error handling

The current code will not remove the sysfs files for fan numbers three
and up. Also, upon exit, fans one and two are removed regardless of
their existence.  This patch cleans up the sysfs error handling for
the fans.

Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

hwmon: (asc7621) Bug fixes

* Allow fan minimum RPM to be set to zero without triggering alarms.
* Fix voltage scaling arithmetic and correct scale factors.
* Correct fan1-fan4 alarm bit shifts.
* Correct register address for temp3_smoothing_enable.
* Read the alarm registers with high priority.

Signed-off-by: Ken Milmore <ken.milmore@googlemail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

kprobes/x86: Fix removed int3 checking order

Fix kprobe/x86 to check removed int3 when failing to get kprobe
from hlist. Since we have a time window between checking int3
exists on probed address and getting kprobe on that address,
we can have following scenario:

 -------
 CPU1                     CPU2
 hit int3
 check int3 exists
                          remove int3
                          remove kprobe from hlist
 get kprobe from hlist
 no kprobe->OOPS!
 -------

This patch moves int3 checking if there is no kprobe on that
address for fixing this problem as follows:

 ------
 CPU1                     CPU2
 hit int3
                          remove int3
                          remove kprobe from hlist
 get kprobe from hlist
 no kprobe->check int3 exists
          ->rollback&retry
 ------

Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Acked-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: systemtap <systemtap@sources.redhat.com>
Cc: DLE <dle-develop@lists.sourceforge.net>
Cc: Dave Anderson <anderson@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <20100427223348.2322.9112.stgit@localhost6.localdomain6>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

perf: Fix static strings treated like dynamic ones

The raw_field_ptr() helper, used to retrieve the address of a field
inside a trace event, treats every strings as if they were dynamic
ie: having a secondary level of indirection to retrieve their
contents.

FIELD_IS_STRING doesn't mean FIELD_IS_DYNAMIC, we only need to
compute the secondary dereference for the latter case.

This fixes perf sched segfaults, bad cmdline report and may be
some other bugs.

Reported-by: Jason Baron <jbaron@redhat.com>
Reported-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Tom Zanussi <tzanussi@gmail.com>

Merge branch 'master' of git://git./linux/kernel/git/kaber/nf-next-2.6

Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-2.6

drm/radeon: Fix 3 regressions - since buffer rework

Commit b4fe945405e477cded91772b4fec854705443dd5 introduced 3 bugs,
fix them:

* Use the right command dword for second packet offset in
  RADEON_CNTL_PAINT/BITBLT_MULTI.
* Don't leak memory if drm_buffer_copy_from_user() fails.
* Don't call drm_buffer_unprocessed() unless drm_buffer_alloc() and
  drm_buffer_copy_from_user() have been called successfully first.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Pauli Nieminen <suokkos@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

wireless: depends on NET

When CONFIG_NET is disabled, the attempt to build wext-priv.c
fails with:

net/wireless/wext-priv.c: In function 'ioctl_private_call':
net/wireless/wext-priv.c:207: error: implicit declaration of function 'call_commit_handler'

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wireless: rt2x00: rt2800usb: replace X by x

s/X/x

Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Clean up generic procedures on descriptor writing.

With a little bit of restructuring it isn't necessary to have special
cases in rt2x00queue_write_tx_descriptor for writing the descriptor
for beacons.
Simply split off the kicking of the TX queue to a separate function
with is only called for non-beacons.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Fix beaconing on rt2800.

According to the Ralink vendor driver for rt2800 we don't need a full
TXD for a beacon but just a TXWI in front of the actual beacon.
Fix the rt2800pci and rt2800usb beaconing code accordingly.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: provide beacon's txdesc to write_beacon callback function.

Preparation to fix rt2800 beaconing.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Clean up all driver's kick_tx_queue callback functions.

All of the driver's kick_tx_queue callback functions treat the TX queue
for beacons in a special manner.
Clean this up by integrating the kicking of the beacon queue into the
write_beacon callback function, and let the generic code no longer call
the kick_tx_queue callback function when updating the beacon.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Factor out RXWI processing to common rt2800 code.

RXWI processing is exactly the same for rt2800pci and rt2800usb, so
make it common code.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Factor out TXWI writing to common rt2800 code.

TXWI writing is exactly the same for rt2800pci and rt2800usb, so
make it common code.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Don't check whether hardware crypto is enabled when reading RXD.

We should simply follow what the hardware told us it has done.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Clean up rt2800usb.h.

Remove unused RXD_DESC_SIZE define and remove duplicated RXWI definitions
from rt2800.h.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Fix setting of txdesc->length field.

We should take the stripping of the IV into account for the txdesc->length
field.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Tested-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: several off by one range checks

There are several places that use > ARRAY_SIZE() instead of
>= ARRAY_SIZE().

Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k/htc_drv_main: off by one error

I changed "> ATH9K_HTC_MAX_TID" to ">= ATH9K_HTC_MAX_TID" to avoid a
potential overflow.

Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k/htc_drv_main: null dereference typo

This is a stray null dereference.  We initialize "ista" properly later on.

Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: remove stray mutex_unlock()

This mutex_unlock() has been here from the initial commit, but as nearly
as I can tell, there isn't a reason for it.

Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: enable PCIe low power mode for AR9003

Cc: Paul Shaw <paul.shaw@atheros.com>
Cc: Don Breslin <don.breslin@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtl8180: change PCI DMA mask to DMA_BIT_MASK(32)

From the original report:

"I had problems to get my rtl8185 PCI card running on Sparc64: I always
got an error about "No suitable DMA available" followed by an error
that no device could be detected. When comparing the rtl8180 driver to
others I noticed that others are mostly using DMA_BIT_MASK so I changed
the custom mask to DMA_BIT_MASK(32) which fixed my issue."

Reported-by: Tiziano Müller <tm@dev-zero.ch>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'fix/hda' of git://git./linux/kernel/git/tiwai/sound-2.6

* 'fix/hda' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  ALSA: Revert "ALSA: hda/realtek: quirk for D945GCLF2 mainboard"
  ALSA: hda - add support for Lenovo ThinkPad X100e in conexant codec
  ALSA: hda - fix DG45ID SPDIF output

autofs4-2.6.34-rc1 - fix link_count usage

After commit 1f36f774b2 ("Switch !O_CREAT case to use of do_last()") in
2.6.34-rc1 autofs direct mounts stopped working.  This is caused by
current->link_count being 0 when ->follow_link() is called from
do_filp_open().

I can't work out why this hasn't been seen before Als patch series.

This patch removes the autofs dependence on current->link_count.

Signed-off-by: Ian Kent <raven@themaw.net>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

netfilter: use rcu_dereference_protected()

Restore the rcu_dereference() calls in conntrack/expectation notifier
and logger registration/unregistration, but use the _protected variant,
which will be required by the upcoming __rcu annotations.

Based on patch by Eric Dumazet <eric.dumazet@gmail.com>

Signed-off-by: Patrick McHardy <kaber@trash.net>

Merge branch 'for-linus' of git://git./linux/kernel/git/jikos/hid

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
  HID: fix suspend crash by moving initializations earlier
  HID: sony: fix sony_set_operational_bt
  HID: ntrig: Remove unused macro, TripleTap and QuadTap
  HID: ntrig: TipSwitch for single touch mode touch.
  HID: hidraw: fix numbered reports
  HID: wacom: remove annoying non-error printk
  HID: ntrig: Emit TOUCH with DOUBLETAP for single touch
  HID: add support for cymotion master solar keyboard
  HID: ntrig: explain firmware quirk
  HID: fix N-trig touch panel with recent firmware

Merge branch 'master' of /repos/git/net-next-2.6

Conflicts:
net/bridge/br_device.c
net/bridge/br_forward.c

Signed-off-by: Patrick McHardy <kaber@trash.net>

netfilter: nf_conntrack_proto: fix warning with CONFIG_PROVE_RCU

===================================================
[ INFO: suspicious rcu_dereference_check() usage. ]
---------------------------------------------------
include/net/netfilter/nf_conntrack_l3proto.h:92 invoked rcu_dereference_check()
without protection!

other info that might help us debug this:

rcu_scheduler_active = 1, debug_locks = 0
2 locks held by iptables/3197:
 #0:  (sk_lock-AF_INET){+.+.+.}, at: [<ffffffff8149bd8c>]
ip_setsockopt+0x7c/0xa0
 #1:  (&xt[i].mutex){+.+.+.}, at: [<ffffffff8148a5fe>]
xt_find_table_lock+0x3e/0x110

stack backtrace:
Pid: 3197, comm: iptables Not tainted 2.6.34-rc4 #2
Call Trace:
 [<ffffffff8105e2e8>] lockdep_rcu_dereference+0xb8/0xc0
 [<ffffffff8147fb3b>] nf_ct_l3proto_module_put+0x6b/0x70
 [<ffffffff8148d891>] state_mt_destroy+0x11/0x20
 [<ffffffff814d3baf>] cleanup_match+0x2f/0x50
 [<ffffffff814d3c63>] cleanup_entry+0x33/0x90
 [<ffffffff814d5653>] ? __do_replace+0x1a3/0x210
 [<ffffffff814d564c>] __do_replace+0x19c/0x210
 [<ffffffff814d651a>] do_ipt_set_ctl+0x16a/0x1b0
 [<ffffffff8147a610>] nf_sockopt+0x60/0xa0
...

The __nf_ct_l3proto_find() call doesn't actually need rcu read side
protection since the caller holds a reference to the protocol. Use
rcu_read_lock() anyways to avoid the warning.

Kernel bugzilla #15781: https://bugzilla.kernel.org/show_bug.cgi?id=15781

Reported-by: Christian Casteyde <casteyde.christian@free.fr>
Signed-off-by: Patrick McHardy <kaber@trash.net>

ALSA: Revert "ALSA: hda/realtek: quirk for D945GCLF2 mainboard"

This reverts commit 7aee67466536bbf8bb44a95712c848a61c5a0acd.

As it doesn't seem to be universally valid for all mainboard revisions of
the D945GCLF2 and breaks snd-hda-intel/ snd-hda-codec-realtek on the Intel
Corporation "D945GCLF2" (LF94510J.86A.0229.2009.0729.0209) mainboard.

00:1b.0 Audio device [0403]: Intel Corporation N10/ICH 7 Family High Definition Audio Controller [8086:27d8] (rev 01)

Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Cc: <stable@kernel.org> [2.6.33]
Signed-off-by: Takashi Iwai <tiwai@suse.de>

net: trans_start cleanups

Now that core network takes care of trans_start updates, dont do it
in drivers themselves, if possible. Drivers can avoid one cache miss
(on dev->trans_start) in their start_xmit() handler.

Exceptions are NETIF_F_LLTX drivers

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: Fix FDDI and TR config checks in ipv4 arp and LLC.

Need to check both CONFIG_FOO and CONFIG_FOO_MODULE

Signed-off-by: David S. Miller <davem@davemloft.net>