Gabor Juhos [Fri, 24 Jan 2014 17:40:17 +0000 (17:40 +0000)]
ar71xx: fix bad RX sensitivity on newer TL-WDR4300 boards
On recent TL-WDR4300 boards the external LNAs of the 2.4GHz
interface are connected to GPIO lines. Because these GPIO
lines are disabled by default, the RX sensitivity of the
device is quite bad.
Setup the GPIOs of the external LNAs to fix the issue.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39392
Gabor Juhos [Fri, 24 Jan 2014 17:15:03 +0000 (17:15 +0000)]
ar71xx: image: generate sysupgrade images for the Compex boards
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39391
Gabor Juhos [Fri, 24 Jan 2014 17:15:02 +0000 (17:15 +0000)]
ar71xx: add sysupgrade support for the Compex boards
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39390
Gabor Juhos [Fri, 24 Jan 2014 17:15:01 +0000 (17:15 +0000)]
ar71xx: image: use a single firmware partition on Compex devices
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39389
Gabor Juhos [Fri, 24 Jan 2014 17:15:01 +0000 (17:15 +0000)]
ar71xx: enable MTD_SPLIT_LZMA_FW option
It will be used for Compex devices.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39388
Gabor Juhos [Fri, 24 Jan 2014 17:14:59 +0000 (17:14 +0000)]
kernel/3.1x: add split code for LZMA compressed kernel based firmwares
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39387
Luka Perkov [Fri, 24 Jan 2014 13:49:39 +0000 (13:49 +0000)]
config: lxc: enable KERNEL_POSIX_MQUEUE
Recent lxc versions are not useful if this option is not enabled. That said,
enable KERNEL_POSIX_MQUEUE by default when KERNEL_LXC_MISC is selected.
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 39385
Gabor Juhos [Fri, 24 Jan 2014 11:59:35 +0000 (11:59 +0000)]
ar71xx: image: detect partition sizes in the Image/Build/Ath macro
Get the size of the mtd partitions directly from the
MTD layout and remove the superfluous macro parameters.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39384
Gabor Juhos [Fri, 24 Jan 2014 11:59:32 +0000 (11:59 +0000)]
ar71xx: image: fix size verification in the CatFiles macro
The macro checks the size of the rootfs image even if
the second parameter of the macro contains the size of
an eraseblock. It is wrong because the size of the
kernel image will be adjusted to the next eraseblock
and the resulting image might be too large.
Fix the macro to check the size of the final image
instead of the rootfs image.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39383
Gabor Juhos [Fri, 24 Jan 2014 08:48:10 +0000 (08:48 +0000)]
Revert "kernel: create firmware partition from MyLoader partition parser"
This reverts r38197.
The automatically created firmware partition includes
the partition_table partition. Apart from the partition
table, this partition contains sensitive data on some
Compex devices which data can be destroyed when the
firmware partition gets modified. Revert the change to
prevent that.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39382
Luka Perkov [Fri, 24 Jan 2014 00:07:48 +0000 (00:07 +0000)]
uboot-envtools: add support for wndr3700
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 39380
Gabor Juhos [Thu, 23 Jan 2014 16:47:42 +0000 (16:47 +0000)]
ar71xx: ap83: define mtd layout via command line
Also use the RKuImage macro becasue the original
firmware starts with the rootfs.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39379
Gabor Juhos [Thu, 23 Jan 2014 16:47:41 +0000 (16:47 +0000)]
ar71xx: ap81: define mtd layout via command line
Also use the RKuImage macro becasue the original
firmware starts with the rootfs.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39378
Gabor Juhos [Thu, 23 Jan 2014 12:27:28 +0000 (12:27 +0000)]
ar71xx: image: show size limit in warning messages
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39376
Gabor Juhos [Thu, 23 Jan 2014 12:23:10 +0000 (12:23 +0000)]
ar71xx: add initramfs image support for Compex devices
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39375
Gabor Juhos [Thu, 23 Jan 2014 12:23:08 +0000 (12:23 +0000)]
ar71xx: wp543: use KEY_RESET code for the sw4 button
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39374
Luka Perkov [Thu, 23 Jan 2014 11:33:42 +0000 (11:33 +0000)]
ar71xx: create wndr3700 network config from uci-defaults
Since that was the last configuration in defconfig directory we can drop the
defconfig init script too.
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 39373
Luka Perkov [Thu, 23 Jan 2014 11:33:41 +0000 (11:33 +0000)]
base-files: add ucidef_add_switch_port function
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 39372
Steven Barth [Thu, 23 Jan 2014 11:02:18 +0000 (11:02 +0000)]
odhcpd: fix certain config values being overwritten
Thanks to Hans Dedecker for the fix.
SVN-Revision: 39371
Steven Barth [Thu, 23 Jan 2014 10:59:04 +0000 (10:59 +0000)]
6rd: Make don't fragment bit (df) a configurable variable
Make the IPv4 "do not fragment" bit a configurable variable for the 6rd
tunnel interface as the bit should not be set in the encapsulating IPv4
header according to RFC3056.
On top the config variable allows to enable/disable path mtu discovery
for tunnel interfaces.
Config variable can be passed to netifd as tunnel config support is
already present for the "do not fragment" bit.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
SVN-Revision: 39370
Gabor Juhos [Thu, 23 Jan 2014 09:07:49 +0000 (09:07 +0000)]
kernel/3.10: update pci_disable_usb_common_quirks patch
Fix build errors caused by undefined 'usb_disable_xhci_ports'
symbol.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39369
Gabor Juhos [Thu, 23 Jan 2014 06:55:58 +0000 (06:55 +0000)]
mpc85xx: Fix building ramdisk images
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39368
Gabor Juhos [Thu, 23 Jan 2014 06:55:50 +0000 (06:55 +0000)]
mpc85xx: Remove inittab workaround
The default inittab uses "askconsole" which is implemented by procd
and uses the console provided by the kernel command line.
Hence, this platform specific workaround is not necessary anymore.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39367
John Crispin [Wed, 22 Jan 2014 15:33:16 +0000 (15:33 +0000)]
ubox: revert log buffer size changes
the fix horribly broke existing setups
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 39366
John Crispin [Tue, 21 Jan 2014 20:59:04 +0000 (20:59 +0000)]
ubox: update to latest git head
make sure log buffer size is not bigger than the ubus message size
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 39365
Florian Fainelli [Tue, 21 Jan 2014 18:50:26 +0000 (18:50 +0000)]
brcm63xx: enable support for BCM63268
Support for the BCM63268 is usable, enable it by default.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 39364
Florian Fainelli [Tue, 21 Jan 2014 18:50:11 +0000 (18:50 +0000)]
brcm63xx: add support for BCM963269BHR board
Add kernel support for the BCM963269BHR board, USB and Ethernet switch,
LEDs and buttons are working.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 39363
Florian Fainelli [Tue, 21 Jan 2014 18:49:50 +0000 (18:49 +0000)]
brcm63xx: improve BCM63268 support
Allow using the HSSPI controller since it works just fine, as well as
the integrated switch core, since that one works too.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 39362
Gabor Juhos [Tue, 21 Jan 2014 17:17:42 +0000 (17:17 +0000)]
ar71xx: mynet-n750: define LEDs connected to the AR8327 switch
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/4743/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39361
Zoltan Herpai [Tue, 21 Jan 2014 14:43:50 +0000 (14:43 +0000)]
modules: swconfig.c: update the error path on 3.13, and behave nicely with return
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
SVN-Revision: 39360
Zoltan Herpai [Tue, 21 Jan 2014 14:24:45 +0000 (14:24 +0000)]
modules: update swconfig.c to compile on 3.13 (compile-tested)
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
SVN-Revision: 39359
Zoltan Herpai [Tue, 21 Jan 2014 14:23:00 +0000 (14:23 +0000)]
add missing symbols
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
SVN-Revision: 39358
Jonas Gorski [Tue, 21 Jan 2014 12:11:18 +0000 (12:11 +0000)]
kernel: ocf: add missing dependency for hifn driver
The HIFN driver is a PCI driver, thus requires PCI support to be enabled
to compile. Therefore let it depend on PCI..
Should fix mvebu builds.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 39357
John Crispin [Tue, 21 Jan 2014 09:51:16 +0000 (09:51 +0000)]
lantiq: fix unaligned access in vdsl firmware extractor
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 39356
Zoltan Herpai [Tue, 21 Jan 2014 07:53:11 +0000 (07:53 +0000)]
add missing symbols
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
SVN-Revision: 39355
Hauke Mehrtens [Mon, 20 Jan 2014 20:01:22 +0000 (20:01 +0000)]
b53: use drvdata to store driver data
we should not abuse the platform_data pointer.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 39354
Hauke Mehrtens [Mon, 20 Jan 2014 19:07:18 +0000 (19:07 +0000)]
b53: make b53_switch_reset_gpio() static
SVN-Revision: 39353
John Crispin [Mon, 20 Jan 2014 18:42:58 +0000 (18:42 +0000)]
procd: update to latest git head
Fixes OpenWrt bug #14832
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 39352
Steven Barth [Mon, 20 Jan 2014 18:23:02 +0000 (18:23 +0000)]
netifd: don't add unnecessary NOP policy rules
SVN-Revision: 39351
Zoltan Herpai [Mon, 20 Jan 2014 15:23:27 +0000 (15:23 +0000)]
update ocf patches - as ENT_DEBUG is removed, move the messages into pr_notice
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
SVN-Revision: 39350
Imre Kaloz [Mon, 20 Jan 2014 14:46:29 +0000 (14:46 +0000)]
update/fixup overlayfs patch
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 39349
Imre Kaloz [Mon, 20 Jan 2014 13:56:24 +0000 (13:56 +0000)]
add initial 3.13 support
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 39348
Steven Barth [Mon, 20 Jan 2014 12:53:15 +0000 (12:53 +0000)]
6in4: fix typo in config variable (fixes #14830)
SVN-Revision: 39347
Gabor Juhos [Mon, 20 Jan 2014 10:23:06 +0000 (10:23 +0000)]
ar71xx: tl-wr1043nd-v2: define LEDs connected to the AR8327 switch
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39346
Gabor Juhos [Mon, 20 Jan 2014 10:23:05 +0000 (10:23 +0000)]
ar71xx: tl-wdr4300: define LEDs connected to the AR8327 switch
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39345
Gabor Juhos [Mon, 20 Jan 2014 10:23:04 +0000 (10:23 +0000)]
ar71xx: set default LED config for the RB2011* boards
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39344
Gabor Juhos [Mon, 20 Jan 2014 10:23:03 +0000 (10:23 +0000)]
ar71xx: set status_led for the RB2011* boards
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39343
Gabor Juhos [Mon, 20 Jan 2014 10:23:02 +0000 (10:23 +0000)]
ar71xx: fix indentation in diag.sh
Replace the leading spaces with tabs.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39342
Gabor Juhos [Mon, 20 Jan 2014 10:23:01 +0000 (10:23 +0000)]
ar71xx: rb2011: define LEDs connected to the AR8327 switch
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39341
Gabor Juhos [Mon, 20 Jan 2014 10:23:00 +0000 (10:23 +0000)]
ar71xx: enable AR8327 LED support
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39340
Gabor Juhos [Mon, 20 Jan 2014 10:22:59 +0000 (10:22 +0000)]
kernel/3.1[02]: add AR8216_PHY_LEDS option
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39339
Gabor Juhos [Mon, 20 Jan 2014 10:22:56 +0000 (10:22 +0000)]
generic: ar8216: add custom LED support for the AR8327 switch
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39338
Gabor Juhos [Mon, 20 Jan 2014 10:22:55 +0000 (10:22 +0000)]
generic: ar8216: allow to use chip specific cleanup callback
It will be used for AR8327.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39337
Gabor Juhos [Mon, 20 Jan 2014 10:22:54 +0000 (10:22 +0000)]
generic: ar8216: add optimized rmw operation
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39336
Gabor Juhos [Mon, 20 Jan 2014 10:22:49 +0000 (10:22 +0000)]
ar71xx: rb2011: fix eth5 LED
The eth5 LED on the RB2011 is not working because the
LED control rule is missing. Fix it.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39335
John Crispin [Sun, 19 Jan 2014 19:10:09 +0000 (19:10 +0000)]
ubox: update to latest git head
adds option to set internal buffer size
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 39333
Steven Barth [Sun, 19 Jan 2014 17:35:33 +0000 (17:35 +0000)]
firewall: don't reload if there were no address or data changes
This fixes packet loss due to reloading firewall every minute with IPv6
implementation of certain ISPs.
SVN-Revision: 39332
John Crispin [Sun, 19 Jan 2014 17:27:40 +0000 (17:27 +0000)]
kernel: add usb3 module definitions
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 39331
John Crispin [Sun, 19 Jan 2014 17:27:31 +0000 (17:27 +0000)]
ralink: activate xhci config
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 39330
John Crispin [Sun, 19 Jan 2014 17:27:22 +0000 (17:27 +0000)]
ralink: backport various fixes from linux-mti
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 39329
John Crispin [Sun, 19 Jan 2014 17:27:13 +0000 (17:27 +0000)]
ralink: add xhci driver
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 39328
John Crispin [Sun, 19 Jan 2014 17:27:04 +0000 (17:27 +0000)]
scripts/kconfig.pl: Indicate which file we couldn't open
Signed-off-by: Daniel Colascione <dancol@dancol.org>
SVN-Revision: 39327
Jonas Gorski [Sun, 19 Jan 2014 14:00:18 +0000 (14:00 +0000)]
brcm63xx: fix typo breaking build in r39325
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 39326
Jonas Gorski [Sun, 19 Jan 2014 13:46:25 +0000 (13:46 +0000)]
brcm63xx: set usb host port number for some devices
Update a few devices with their actual port numbers, especially those
with two ports.
Should allow properly using the second port on the Neufboxen and HW553
and HW556.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 39325
Jonas Gorski [Sun, 19 Jan 2014 13:46:14 +0000 (13:46 +0000)]
brcm63xx: allow setting the number of usb host ports for boards
Allow setting the number of available usb host ports for boards with
additional sanity checks to allow using the second port on devices
where it is available.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 39324
Jonas Gorski [Sun, 19 Jan 2014 13:46:05 +0000 (13:46 +0000)]
brcm63xx: add USB support for BCM63268
Add and enable USB support for the BCM63268 family of SoCs.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 39323
Jonas Gorski [Sun, 19 Jan 2014 13:45:55 +0000 (13:45 +0000)]
brcm63xx: BCM6318 needs to select _HAS_OHCI/EHCI too
USB will fail to work if compiling with BCM6318 only if BCM63XX_HAS_EHCI
and BCM63XX_HAS_OHCI are not selected.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 39322
Jonas Gorski [Sun, 19 Jan 2014 13:45:42 +0000 (13:45 +0000)]
brcm63xx: prevent usb clock state inconsistency on BCM6318
Return the same clock for usbh and usbd on BCM6318 to prevent the clock
getting disabled despite being supposed to be enabled, e.g. by the
following sequence:
clk_enable(usbh); <- usbh->usage = 1, enabled
clk_enable(usbd); <- usbd->usage = 1, enabled (no effect)
clk_disable(usbd); <- usbd->usage = 0, -> disabled!
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 39321
Imre Kaloz [Sat, 18 Jan 2014 19:44:40 +0000 (19:44 +0000)]
generate images for the On Networks N150 (rebranded Netgear WNR612v2)
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 39320
Steven Barth [Sat, 18 Jan 2014 10:11:03 +0000 (10:11 +0000)]
odhcpd: Fix a memory corruption when static leases are used
SVN-Revision: 39319
John Crispin [Fri, 17 Jan 2014 22:12:05 +0000 (22:12 +0000)]
sysupgrade: do not kill any processes in failsafe
sysugrade killed the lock causing failsafe to stop
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 39318
John Crispin [Fri, 17 Jan 2014 21:45:55 +0000 (21:45 +0000)]
usbmode: update usb-modeswitch-data version to
20131113
https://dev.openwrt.org/ticket/14762
Signed-off-by: Alif M. Ahmad <ama_alif@yahoo.co.id>
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 39317
John Crispin [Fri, 17 Jan 2014 21:35:32 +0000 (21:35 +0000)]
ubox: update to latest git
- fix duplicate device wildcard
- fix elf 64bit elf parsing
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 39316
Steven Barth [Fri, 17 Jan 2014 19:05:54 +0000 (19:05 +0000)]
odhcpd: be even less verbose and don't start unnecessary relays
SVN-Revision: 39315
Steven Barth [Fri, 17 Jan 2014 15:53:43 +0000 (15:53 +0000)]
odhcpd: fix logspam
SVN-Revision: 39314
Steven Barth [Fri, 17 Jan 2014 15:48:02 +0000 (15:48 +0000)]
odhcpd: use hybrid management mode by default
SVN-Revision: 39313
Steven Barth [Fri, 17 Jan 2014 14:00:09 +0000 (14:00 +0000)]
dnsmasq: add dnsmasq.d config folder & improve odhcpd coexistence
SVN-Revision: 39312
Steven Barth [Fri, 17 Jan 2014 14:00:04 +0000 (14:00 +0000)]
odhcp6c: Use sourcerouting by default
SVN-Revision: 39311
Steven Barth [Fri, 17 Jan 2014 14:00:00 +0000 (14:00 +0000)]
odhcp6c: fix several small issues + decrease size
SVN-Revision: 39310
Steven Barth [Fri, 17 Jan 2014 13:59:55 +0000 (13:59 +0000)]
target: replace 6relayd with odhcpd by default
SVN-Revision: 39309
Steven Barth [Fri, 17 Jan 2014 13:59:51 +0000 (13:59 +0000)]
odhcpd: several bugfixes and improved integration
SVN-Revision: 39308
Steven Barth [Fri, 17 Jan 2014 13:59:47 +0000 (13:59 +0000)]
6in4, 6rd, 6to4: Use source-restricted routes by default
SVN-Revision: 39307
Steven Barth [Fri, 17 Jan 2014 13:59:40 +0000 (13:59 +0000)]
netifd: Add IFUPDATE-flags and use main IPv6 routing table again
SVN-Revision: 39306
John Crispin [Fri, 17 Jan 2014 13:57:25 +0000 (13:57 +0000)]
kexec: bump to latest head revision
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 39305
Florian Fainelli [Thu, 16 Jan 2014 00:45:19 +0000 (00:45 +0000)]
brcm63xx: do not add twice the same field to board
Changeset r39302 updated a board section and added twice .has_ehci0,
this is not necessary, so fix it.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 39304
John Crispin [Wed, 15 Jan 2014 19:16:51 +0000 (19:16 +0000)]
lantiq: Add support for Astoria ARV7510PW22
This board is pretty similar to ARV752DPW22.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 39303
Florian Fainelli [Wed, 15 Jan 2014 19:05:57 +0000 (19:05 +0000)]
brcm63xx: add USB support to BCM6318
BCM6318 has a special initialization sequence which involves touching
PLL control registers in the USBH_PRIV register space, as well as
toggling a bit the Simulation control register.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 39302
Luka Perkov [Wed, 15 Jan 2014 18:38:51 +0000 (18:38 +0000)]
mvebu: fix build failures when initramfs is not selected
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 39301
John Crispin [Wed, 15 Jan 2014 18:29:59 +0000 (18:29 +0000)]
firewall: improve logging in hotplug script
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 39300
John Crispin [Wed, 15 Jan 2014 18:29:51 +0000 (18:29 +0000)]
ramips: Add profile for the Edimax BR-6475nD
Signed-off-by: Christopher Lais <chris+openwrt@zenthought.org>
SVN-Revision: 39299
John Crispin [Wed, 15 Jan 2014 18:29:44 +0000 (18:29 +0000)]
ramips: Add userspace support for the Edimax BR-6475nD
The rt2x00 wifi driver may still need updating to
function with this device.
Signed-off-by: Christopher Lais <chris+openwrt@zenthought.org>
SVN-Revision: 39298
John Crispin [Wed, 15 Jan 2014 18:29:03 +0000 (18:29 +0000)]
ramips: rt3883: Fix a typo in rt3883.dtsi
Signed-off-by: Christopher Lais <chris+openwrt@zenthought.org>
SVN-Revision: 39297
Luka Perkov [Wed, 15 Jan 2014 14:11:36 +0000 (14:11 +0000)]
lantiq: update kernel configuration
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 39296
Zoltan Herpai [Wed, 15 Jan 2014 09:28:41 +0000 (09:28 +0000)]
packages: ifenslave: add kernel dependencies as source was removed from 3.12
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
SVN-Revision: 39295
Florian Fainelli [Wed, 15 Jan 2014 00:06:08 +0000 (00:06 +0000)]
brcm63xx: fix BCM96318MVWG LEDs
Power LED is not active low, and ppp-fail is red, not green.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 39294
Florian Fainelli [Wed, 15 Jan 2014 00:05:51 +0000 (00:05 +0000)]
brcm63xx: remove config-3.11
This was not supposed to be committed, remove it.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 39293
Florian Fainelli [Tue, 14 Jan 2014 23:56:46 +0000 (23:56 +0000)]
brcm63xx: 96368MVWG supports USB gadget, enable it
Enable the use of the USB gadget device at the board level so we can use
bcm63xx_udc on this board.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 39292
Florian Fainelli [Tue, 14 Jan 2014 23:56:28 +0000 (23:56 +0000)]
brcm63xx: replace gadget driver build fix with upstream submission
Also fixing a build warning due to a misplaced parenthesis in the
previous submission.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 39291
Hauke Mehrtens [Tue, 14 Jan 2014 23:11:10 +0000 (23:11 +0000)]
gpio-button-hotplug: add wwan button
The wimax key will be used as a generic wwan key starting with Linux
3.13. The brcm47xx target uses this key for the 3g buttons. Also remove
the ifdef around KEY_WPS_BUTTON, this is in the kernel for a long time
now.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 39290
Hauke Mehrtens [Tue, 14 Jan 2014 22:51:30 +0000 (22:51 +0000)]
packages: kernel: reverse kernel dependencies logic
This will select the correct dependencies also for more recent kernel versions.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 39289
projects / openwrt / staging / robimarko.git / log