git.openwrt.org Git - openwrt/staging/blogic.git/log

net: dev: Use unsigned integer as an argument to left-shift

1 << 31 is Undefined Behaviour according to the C standard.
Use U type modifier to avoid theoretical overflow.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Drop oversize TX packets to prevent errors.

There have been reports of oversize UDP packets being sent to the
driver to be transmitted, causing error conditions.  The issue is
likely caused by the dst of the SKB switching between 'lo' with
64K MTU and the hardware device with a smaller MTU.  Patches are
being proposed by Mahesh Bandewar <maheshb@google.com> to fix the
issue.

In the meantime, add a quick length check in the driver to prevent
the error.  The driver uses the TX packet size as index to look up an
array to setup the TX BD.  The array is large enough to support all MTU
sizes supported by the driver.  The oversize TX packet causes the
driver to index beyond the array and put garbage values into the
TX BD.  Add a simple check to prevent this.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: fix race condition causing hung sendto

When sending multicast messages via blocking socket,
if sending link is congested (tsk->cong_link_cnt is set to 1),
the sending thread will be put into sleeping state. However,
tipc_sk_filter_rcv() is called under socket spin lock but
tipc_wait_for_cond() is not. So, there is no guarantee that
the setting of tsk->cong_link_cnt to 0 in tipc_sk_proto_rcv() in
CPU-1 will be perceived by CPU-0. If that is the case, the sending
thread in CPU-0 after being waken up, will continue to see
tsk->cong_link_cnt as 1 and put the sending thread into sleeping
state again. The sending thread will sleep forever.

CPU-0                                | CPU-1
tipc_wait_for_cond()                 |
{                                    |
// condition_ = !tsk->cong_link_cnt |
while ((rc_ = !(condition_))) {     |
  ...                                |
  release_sock(sk_);                 |
  wait_woken();                      |
                                     | if (!sock_owned_by_user(sk))
                                     |  tipc_sk_filter_rcv()
                                     |  {
                                     |   ...
                                     |   tipc_sk_proto_rcv()
                                     |   {
                                     |    ...
                                     |    tsk->cong_link_cnt--;
                                     |    ...
                                     |    sk->sk_write_space(sk);
                                     |    ...
                                     |   }
                                     |   ...
                                     |  }
  sched_annotate_sleep();            |
  lock_sock(sk_);                    |
  remove_wait_queue();               |
}                                   |
}                                    |

This commit fixes it by adding memory barrier to tipc_sk_proto_rcv()
and tipc_wait_for_cond().

Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

hv_netvsc: Fix IP header checksum for coalesced packets

Incoming packets may have IP header checksum verified by the host.
They may not have IP header checksum computed after coalescing.
This patch re-compute the checksum when necessary, otherwise the
packets may be dropped, because Linux network stack always checks it.

Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'net-fail-route'

David Ahern says:

====================
net: Fail route add with unsupported nexthop attribute

RTA_VIA was added for MPLS as a way of specifying a gateway from a
different address family. IPv4 and IPv6 do not currently support RTA_VIA
so using it leads to routes that are not what the user intended. Catch
and fail - returning a proper error message.

MPLS on the other hand does not support RTA_GATEWAY since it does not
make sense to have a nexthop from the MPLS address family. Similarly,
catch and fail - returning a proper error message.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

mpls: Return error for RTA_GATEWAY attribute

MPLS does not support nexthops with an MPLS address family.
Specifically, it does not handle RTA_GATEWAY attribute. Make it
clear by returning an error.

Fixes: 03c0566542f4c ("mpls: Netlink commands to add, remove, and dump routes")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv6: Return error for RTA_VIA attribute

IPv6 currently does not support nexthops outside of the AF_INET6 family.
Specifically, it does not handle RTA_VIA attribute. If it is passed
in a route add request, the actual route added only uses the device
which is clearly not what the user intended:

  $ ip -6 ro add 2001:db8:2::/64 via inet 172.16.1.1 dev eth0
  $ ip ro ls
  ...
  2001:db8:2::/64 dev eth0 metric 1024 pref medium

Catch this and fail the route add:
  $ ip -6 ro add 2001:db8:2::/64 via inet 172.16.1.1 dev eth0
  Error: IPv6 does not support RTA_VIA attribute.

Fixes: 03c0566542f4c ("mpls: Netlink commands to add, remove, and dump routes")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv4: Return error for RTA_VIA attribute

IPv4 currently does not support nexthops outside of the AF_INET family.
Specifically, it does not handle RTA_VIA attribute. If it is passed
in a route add request, the actual route added only uses the device
which is clearly not what the user intended:

  $ ip ro add 172.16.1.0/24 via inet6 2001:db8:1::1 dev eth0
  $ ip ro ls
  ...
  172.16.1.0/24 dev eth0

Catch this and fail the route add:
  $ ip ro add 172.16.1.0/24 via inet6 2001:db8:1::1 dev eth0
  Error: IPv4 does not support RTA_VIA attribute.

Fixes: 03c0566542f4c ("mpls: Netlink commands to add, remove, and dump routes")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: avoid use IPCB in cipso_v4_error

Extract IP options in cipso_v4_error and use __icmp_send.

Signed-off-by: Sergey Nazarov <s-nazarov@yandex.ru>
Acked-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: Add __icmp_send helper.

Add __icmp_send function having ip_options struct parameter

Signed-off-by: Sergey Nazarov <s-nazarov@yandex.ru>
Reviewed-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tun: remove unnecessary memory barrier

Replace set_current_state with __set_current_state since no memory
barrier is needed at this point.

Signed-off-by: Timur Celik <mail@timurcelik.de>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: socket: set sock->sk to NULL after calling proto_ops::release()

Commit 9060cb719e61 ("net: crypto set sk to NULL when af_alg_release.")
fixed a use-after-free in sockfs_setattr() when an AF_ALG socket is
closed concurrently with fchownat().  However, it ignored that many
other proto_ops::release() methods don't set sock->sk to NULL and
therefore allow the same use-after-free:

    - base_sock_release
    - bnep_sock_release
    - cmtp_sock_release
    - data_sock_release
    - dn_release
    - hci_sock_release
    - hidp_sock_release
    - iucv_sock_release
    - l2cap_sock_release
    - llcp_sock_release
    - llc_ui_release
    - rawsock_release
    - rfcomm_sock_release
    - sco_sock_release
    - svc_release
    - vcc_release
    - x25_release

Rather than fixing all these and relying on every socket type to get
this right forever, just make __sock_release() set sock->sk to NULL
itself after calling proto_ops::release().

Reproducer that produces the KASAN splat when any of these socket types
are configured into the kernel:

    #include <pthread.h>
    #include <stdlib.h>
    #include <sys/socket.h>
    #include <unistd.h>

    pthread_t t;
    volatile int fd;

    void *close_thread(void *arg)
    {
        for (;;) {
            usleep(rand() % 100);
            close(fd);
        }
    }

    int main()
    {
        pthread_create(&t, NULL, close_thread, NULL);
        for (;;) {
            fd = socket(rand() % 50, rand() % 11, 0);
            fchownat(fd, "", 1000, 1000, 0x1000);
            close(fd);
        }
    }

Fixes: 86741ec25462 ("net: core: Add a UID field to struct sock.")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: sched: act_tunnel_key: fix NULL pointer dereference during init

Metadata pointer is only initialized for action TCA_TUNNEL_KEY_ACT_SET, but
it is unconditionally dereferenced in tunnel_key_init() error handler.
Verify that metadata pointer is not NULL before dereferencing it in
tunnel_key_init error handling code.

Fixes: ee28bb56ac5b ("net/sched: fix memory leak in act_tunnel_key_init()")
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: fix a leaked reference by adding missing of_node_put

The call to of_parse_phandle returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.

Detected by coccinelle with the following warnings:
./net/dsa/port.c:294:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 284, but without a corresponding object release within this function.
./net/dsa/dsa2.c:627:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 618, but without a corresponding object release within this function.
./net/dsa/dsa2.c:630:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 618, but without a corresponding object release within this function.
./net/dsa/dsa2.c:636:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 618, but without a corresponding object release within this function.
./net/dsa/dsa2.c:639:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 618, but without a corresponding object release within this function.

Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

tun: fix blocking read

This patch moves setting of the current state into the loop. Otherwise
the task may end up in a busy wait loop if none of the break conditions
are met.

Signed-off-by: Timur Celik <mail@timurcelik.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: lantiq: Add GPHY firmware files

This adds the file names of the FW files which this driver handles into
the module description.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/sched: act_skbedit: fix refcount leak when replace fails

when act_skbedit was converted to use RCU in the data plane, we added an
error path, but we forgot to drop the action refcount in case of failure
during a 'replace' operation:

# tc actions add action skbedit ptype otherhost pass index 100
# tc action show action skbedit
total acts 1

         action order 0: skbedit  ptype otherhost pass
          index 100 ref 1 bind 0
# tc actions replace action skbedit ptype otherhost drop index 100
RTNETLINK answers: Cannot allocate memory
We have an error talking to the kernel
# tc action show action skbedit
total acts 1

         action order 0: skbedit  ptype otherhost pass
          index 100 ref 2 bind 0

Ensure we call tcf_idr_release(), in case 'params_new' allocation failed,
also when the action is being replaced.

Fixes: c749cdda9089 ("net/sched: act_skbedit: don't use spinlock in the data path")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/sched: act_ipt: fix refcount leak when replace fails

After commit 4e8ddd7f1758 ("net: sched: don't release reference on action
overwrite"), the error path of all actions was converted to drop refcount
also when the action was being overwritten. But we forgot act_ipt_init(),
in case allocation of 'tname' was not successful:

# tc action add action xt -j LOG --log-prefix hello index 100
tablename: mangle hook: NF_IP_POST_ROUTING
         target:  LOG level warning prefix "hello" index 100
# tc action show action xt
total acts 1

         action order 0: tablename: mangle  hook: NF_IP_POST_ROUTING
         target  LOG level warning prefix "hello"
         index 100 ref 1 bind 0
# tc action replace action xt -j LOG --log-prefix world index 100
tablename: mangle hook: NF_IP_POST_ROUTING
         target:  LOG level warning prefix "world" index 100
RTNETLINK answers: Cannot allocate memory
We have an error talking to the kernel
# tc action show action xt
total acts 1

         action order 0: tablename: mangle  hook: NF_IP_POST_ROUTING
         target  LOG level warning prefix "hello"
         index 100 ref 2 bind 0

Ensure we call tcf_idr_release(), in case 'tname' allocation failed, also
when the action is being replaced.

Fixes: 4e8ddd7f1758 ("net: sched: don't release reference on action overwrite")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'for-linus' of git://git./virt/kvm/kvm

Pull KVM fixes from Paolo Bonzini:
"Bug fixes"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: MMU: record maximum physical address width in kvm_mmu_extended_role
  kvm: x86: Return LA57 feature based on hardware capability
  x86/kvm/mmu: fix switch between root and guest MMUs
  s390: vsie: Use effective CRYCBD.31 to check CRYCBD validity

Merge git://git./linux/kernel/git/davem/net

Pull networking fixes from David Miller:
"Hopefully the last pull request for this release. Fingers crossed:

   1) Only refcount ESP stats on full sockets, from Martin Willi.

   2) Missing barriers in AF_UNIX, from Al Viro.

   3) RCU protection fixes in ipv6 route code, from Paolo Abeni.

   4) Avoid false positives in untrusted GSO validation, from Willem de
      Bruijn.

   5) Forwarded mesh packets in mac80211 need more tailroom allocated,
      from Felix Fietkau.

   6) Use operstate consistently for linkup in team driver, from George
      Wilkie.

   7) ThunderX bug fixes from Vadim Lomovtsev. Mostly races between VF
      and PF code paths.

   8) Purge ipv6 exceptions during netdevice removal, from Paolo Abeni.

   9) nfp eBPF code gen fixes from Jiong Wang.

  10) bnxt_en firmware timeout fix from Michael Chan.

  11) Use after free in udp/udpv6 error handlers, from Paolo Abeni.

  12) Fix a race in x25_bind triggerable by syzbot, from Eric Dumazet"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (65 commits)
  net: phy: realtek: Dummy IRQ calls for RTL8366RB
  tcp: repaired skbs must init their tso_segs
  net/x25: fix a race in x25_bind()
  net: dsa: Remove documentation for port_fdb_prepare
  Revert "bridge: do not add port to router list when receives query with source 0.0.0.0"
  selftests: fib_tests: sleep after changing carrier. again.
  net: set static variable an initial value in atl2_probe()
  net: phy: marvell10g: Fix Multi-G advertisement to only advertise 10G
  bpf, doc: add bpf list as secondary entry to maintainers file
  udp: fix possible user after free in error handler
  udpv6: fix possible user after free in error handler
  fou6: fix proto error handler argument type
  udpv6: add the required annotation to mib type
  mdio_bus: Fix use-after-free on device_register fails
  net: Set rtm_table to RT_TABLE_COMPAT for ipv6 for tables > 255
  bnxt_en: Wait longer for the firmware message response to complete.
  bnxt_en: Fix typo in firmware message timeout logic.
  nfp: bpf: fix ALU32 high bits clearance bug
  nfp: bpf: fix code-gen bug on BPF_ALU | BPF_XOR | BPF_K
  Documentation: networking: switchdev: Update port parent ID section
  ...

net: phy: realtek: Dummy IRQ calls for RTL8366RB

This fixes a regression introduced by
commit 0d2e778e38e0ddffab4bb2b0e9ed2ad5165c4bf7
"net: phy: replace PHY_HAS_INTERRUPT with a check for
config_intr and ack_interrupt".

This assumes that a PHY cannot trigger interrupt unless
it has .config_intr() or .ack_interrupt() implemented.
A later patch makes the code assume both need to be
implemented for interrupts to be present.

But this PHY (which is inside a DSA) will happily
fire interrupts without either callback.

Implement dummy callbacks for .config_intr() and
.ack_interrupt() in the phy header to fix this.

Tested on the RTL8366RB on D-Link DIR-685.

Fixes: 0d2e778e38e0 ("net: phy: replace PHY_HAS_INTERRUPT with a check for config_intr and ack_interrupt")
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

tcp: repaired skbs must init their tso_segs

syzbot reported a WARN_ON(!tcp_skb_pcount(skb))
in tcp_send_loss_probe() [1]

This was caused by TCP_REPAIR sent skbs that inadvertenly
were missing a call to tcp_init_tso_segs()

[1]
WARNING: CPU: 1 PID: 0 at net/ipv4/tcp_output.c:2534 tcp_send_loss_probe+0x771/0x8a0 net/ipv4/tcp_output.c:2534
Kernel panic - not syncing: panic_on_warn set ...
CPU: 1 PID: 0 Comm: swapper/1 Not tainted 5.0.0-rc7+ #77
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
<IRQ>
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x172/0x1f0 lib/dump_stack.c:113
panic+0x2cb/0x65c kernel/panic.c:214
__warn.cold+0x20/0x45 kernel/panic.c:571
report_bug+0x263/0x2b0 lib/bug.c:186
fixup_bug arch/x86/kernel/traps.c:178 [inline]
fixup_bug arch/x86/kernel/traps.c:173 [inline]
do_error_trap+0x11b/0x200 arch/x86/kernel/traps.c:271
do_invalid_op+0x37/0x50 arch/x86/kernel/traps.c:290
invalid_op+0x14/0x20 arch/x86/entry/entry_64.S:973
RIP: 0010:tcp_send_loss_probe+0x771/0x8a0 net/ipv4/tcp_output.c:2534
Code: 88 fc ff ff 4c 89 ef e8 ed 75 c8 fb e9 c8 fc ff ff e8 43 76 c8 fb e9 63 fd ff ff e8 d9 75 c8 fb e9 94 f9 ff ff e8 bf 03 91 fb <0f> 0b e9 7d fa ff ff e8 b3 03 91 fb 0f b6 1d 37 43 7a 03 31 ff 89
RSP: 0018:ffff8880ae907c60 EFLAGS: 00010206
RAX: ffff8880a989c340 RBX: 0000000000000000 RCX: ffffffff85dedbdb
RDX: 0000000000000100 RSI: ffffffff85dee0b1 RDI: 0000000000000005
RBP: ffff8880ae907c90 R08: ffff8880a989c340 R09: ffffed10147d1ae1
R10: ffffed10147d1ae0 R11: ffff8880a3e8d703 R12: ffff888091b90040
R13: ffff8880a3e8d540 R14: 0000000000008000 R15: ffff888091b90860
tcp_write_timer_handler+0x5c0/0x8a0 net/ipv4/tcp_timer.c:583
tcp_write_timer+0x10e/0x1d0 net/ipv4/tcp_timer.c:607
call_timer_fn+0x190/0x720 kernel/time/timer.c:1325
expire_timers kernel/time/timer.c:1362 [inline]
__run_timers kernel/time/timer.c:1681 [inline]
__run_timers kernel/time/timer.c:1649 [inline]
run_timer_softirq+0x652/0x1700 kernel/time/timer.c:1694
__do_softirq+0x266/0x95a kernel/softirq.c:292
invoke_softirq kernel/softirq.c:373 [inline]
irq_exit+0x180/0x1d0 kernel/softirq.c:413
exiting_irq arch/x86/include/asm/apic.h:536 [inline]
smp_apic_timer_interrupt+0x14a/0x570 arch/x86/kernel/apic/apic.c:1062
apic_timer_interrupt+0xf/0x20 arch/x86/entry/entry_64.S:807
</IRQ>
RIP: 0010:native_safe_halt+0x2/0x10 arch/x86/include/asm/irqflags.h:58
Code: ff ff ff 48 89 c7 48 89 45 d8 e8 59 0c a1 fa 48 8b 45 d8 e9 ce fe ff ff 48 89 df e8 48 0c a1 fa eb 82 90 90 90 90 90 90 fb f4 <c3> 0f 1f 00 66 2e 0f 1f 84 00 00 00 00 00 f4 c3 90 90 90 90 90 90
RSP: 0018:ffff8880a98afd78 EFLAGS: 00000286 ORIG_RAX: ffffffffffffff13
RAX: 1ffffffff1125061 RBX: ffff8880a989c340 RCX: 0000000000000000
RDX: dffffc0000000000 RSI: 0000000000000001 RDI: ffff8880a989cbbc
RBP: ffff8880a98afda8 R08: ffff8880a989c340 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000001
R13: ffffffff889282f8 R14: 0000000000000001 R15: 0000000000000000
arch_cpu_idle+0x10/0x20 arch/x86/kernel/process.c:555
default_idle_call+0x36/0x90 kernel/sched/idle.c:93
cpuidle_idle_call kernel/sched/idle.c:153 [inline]
do_idle+0x386/0x570 kernel/sched/idle.c:262
cpu_startup_entry+0x1b/0x20 kernel/sched/idle.c:353
start_secondary+0x404/0x5c0 arch/x86/kernel/smpboot.c:271
secondary_startup_64+0xa4/0xb0 arch/x86/kernel/head_64.S:243
Kernel Offset: disabled
Rebooting in 86400 seconds..

Fixes: 79861919b889 ("tcp: fix TCP_REPAIR xmit queue setup")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: Andrey Vagin <avagin@openvz.org>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/x25: fix a race in x25_bind()

syzbot was able to trigger another soft lockup [1]

I first thought it was the O(N^2) issue I mentioned in my
prior fix (f657d22ee1f "net/x25: do not hold the cpu
too long in x25_new_lci()"), but I eventually found
that x25_bind() was not checking SOCK_ZAPPED state under
socket lock protection.

This means that multiple threads can end up calling
x25_insert_socket() for the same socket, and corrupt x25_list

[1]
watchdog: BUG: soft lockup - CPU#0 stuck for 123s! [syz-executor.2:10492]
Modules linked in:
irq event stamp: 27515
hardirqs last  enabled at (27514): [<ffffffff81006673>] trace_hardirqs_on_thunk+0x1a/0x1c
hardirqs last disabled at (27515): [<ffffffff8100668f>] trace_hardirqs_off_thunk+0x1a/0x1c
softirqs last  enabled at (32): [<ffffffff8632ee73>] x25_get_neigh+0xa3/0xd0 net/x25/x25_link.c:336
softirqs last disabled at (34): [<ffffffff86324bc3>] x25_find_socket+0x23/0x140 net/x25/af_x25.c:341
CPU: 0 PID: 10492 Comm: syz-executor.2 Not tainted 5.0.0-rc7+ #88
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:__sanitizer_cov_trace_pc+0x4/0x50 kernel/kcov.c:97
Code: f4 ff ff ff e8 11 9f ea ff 48 c7 05 12 fb e5 08 00 00 00 00 e9 c8 e9 ff ff 90 90 90 90 90 90 90 90 90 90 90 90 90 55 48 89 e5 <48> 8b 75 08 65 48 8b 04 25 40 ee 01 00 65 8b 15 38 0c 92 7e 81 e2
RSP: 0018:ffff88806e94fc48 EFLAGS: 00000286 ORIG_RAX: ffffffffffffff13
RAX: 1ffff1100d84dac5 RBX: 0000000000000001 RCX: ffffc90006197000
RDX: 0000000000040000 RSI: ffffffff86324bf3 RDI: ffff88806c26d628
RBP: ffff88806e94fc48 R08: ffff88806c1c6500 R09: fffffbfff1282561
R10: fffffbfff1282560 R11: ffffffff89412b03 R12: ffff88806c26d628
R13: ffff888090455200 R14: dffffc0000000000 R15: 0000000000000000
FS:  00007f3a107e4700(0000) GS:ffff8880ae800000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f3a107e3db8 CR3: 00000000a5544000 CR4: 00000000001406f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
__x25_find_socket net/x25/af_x25.c:327 [inline]
x25_find_socket+0x7d/0x140 net/x25/af_x25.c:342
x25_new_lci net/x25/af_x25.c:355 [inline]
x25_connect+0x380/0xde0 net/x25/af_x25.c:784
__sys_connect+0x266/0x330 net/socket.c:1662
__do_sys_connect net/socket.c:1673 [inline]
__se_sys_connect net/socket.c:1670 [inline]
__x64_sys_connect+0x73/0xb0 net/socket.c:1670
do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x457e29
Code: ad b8 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 7b b8 fb ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007f3a107e3c78 EFLAGS: 00000246 ORIG_RAX: 000000000000002a
RAX: ffffffffffffffda RBX: 0000000000000003 RCX: 0000000000457e29
RDX: 0000000000000012 RSI: 0000000020000200 RDI: 0000000000000005
RBP: 000000000073c040 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00007f3a107e46d4
R13: 00000000004be362 R14: 00000000004ceb98 R15: 00000000ffffffff
Sending NMI from CPU 0 to CPUs 1:
NMI backtrace for cpu 1
CPU: 1 PID: 10493 Comm: syz-executor.3 Not tainted 5.0.0-rc7+ #88
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:__read_once_size include/linux/compiler.h:193 [inline]
RIP: 0010:queued_write_lock_slowpath+0x143/0x290 kernel/locking/qrwlock.c:86
Code: 4c 8d 2c 01 41 83 c7 03 41 0f b6 45 00 41 38 c7 7c 08 84 c0 0f 85 0c 01 00 00 8b 03 3d 00 01 00 00 74 1a f3 90 41 0f b6 55 00 <41> 38 d7 7c eb 84 d2 74 e7 48 89 df e8 cc aa 4e 00 eb dd be 04 00
RSP: 0018:ffff888085c47bd8 EFLAGS: 00000206
RAX: 0000000000000300 RBX: ffffffff89412b00 RCX: 1ffffffff1282560
RDX: 0000000000000000 RSI: 0000000000000004 RDI: ffffffff89412b00
RBP: ffff888085c47c70 R08: 1ffffffff1282560 R09: fffffbfff1282561
R10: fffffbfff1282560 R11: ffffffff89412b03 R12: 00000000000000ff
R13: fffffbfff1282560 R14: 1ffff11010b88f7d R15: 0000000000000003
FS:  00007fdd04086700(0000) GS:ffff8880ae900000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fdd04064db8 CR3: 0000000090be0000 CR4: 00000000001406e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
queued_write_lock include/asm-generic/qrwlock.h:104 [inline]
do_raw_write_lock+0x1d6/0x290 kernel/locking/spinlock_debug.c:203
__raw_write_lock_bh include/linux/rwlock_api_smp.h:204 [inline]
_raw_write_lock_bh+0x3b/0x50 kernel/locking/spinlock.c:312
x25_insert_socket+0x21/0xe0 net/x25/af_x25.c:267
x25_bind+0x273/0x340 net/x25/af_x25.c:703
__sys_bind+0x23f/0x290 net/socket.c:1481
__do_sys_bind net/socket.c:1492 [inline]
__se_sys_bind net/socket.c:1490 [inline]
__x64_sys_bind+0x73/0xb0 net/socket.c:1490
do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x457e29

Fixes: 90c27297a9bf ("X.25 remove bkl in bind")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: andrew hendry <andrew.hendry@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: Remove documentation for port_fdb_prepare

This callback was removed some time ago, also remove the documentation.

Fixes: 1b6dd556c304 ("net: dsa: Remove prepare phase for FDB")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Revert "bridge: do not add port to router list when receives query with source 0.0.0.0"

This reverts commit 5a2de63fd1a5 ("bridge: do not add port to router list
when receives query with source 0.0.0.0") and commit 0fe5119e267f ("net:
bridge: remove ipv6 zero address check in mcast queries")

The reason is RFC 4541 is not a standard but suggestive. Currently we
will elect 0.0.0.0 as Querier if there is no ip address configured on
bridge. If we do not add the port which recives query with source
0.0.0.0 to router list, the IGMP reports will not be about to forward
to Querier, IGMP data will also not be able to forward to dest.

As Nikolay suggested, revert this change first and add a boolopt api
to disable none-zero election in future if needed.

Reported-by: Linus Lüssing <linus.luessing@c0d3.blue>
Reported-by: Sebastian Gottschall <s.gottschall@newmedia-net.de>
Fixes: 5a2de63fd1a5 ("bridge: do not add port to router list when receives query with source 0.0.0.0")
Fixes: 0fe5119e267f ("net: bridge: remove ipv6 zero address check in mcast queries")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

selftests: fib_tests: sleep after changing carrier. again.

Just like commit e2ba732a1681 ("selftests: fib_tests: sleep after
changing carrier"), wait one second to allow linkwatch to propagate the
carrier change to the stack.

There are two sets of carrier tests. The first slept after the carrier
was set to off, and when the second set ran, it was likely that the
linkwatch would be able to run again without much delay, reducing the
likelihood of a race. However, if you run 'fib_tests.sh -t carrier' on a
loop, you will quickly notice the failures.

Sleeping on the second set of tests make the failures go away.

Cc: David Ahern <dsahern@gmail.com>
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: set static variable an initial value in atl2_probe()

cards_found is a static variable, but when it enters atl2_probe(),
cards_found is set to zero, the value is not consistent with last probe,
so next behavior is not our expect.

Signed-off-by: Mao Wenan <maowenan@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: phy: marvell10g: Fix Multi-G advertisement to only advertise 10G

Some Marvell Alaska PHYs support 2.5G, 5G and 10G BaseT links. Their
default behaviour is to advertise all of these modes, but at the moment,
only 10GBaseT is supported. To prevent link partners from establishing
link at that speed, clear these modes upon configuring aneg parameters.

Fixes: 20b2af32ff3f ("net: phy: add Marvell Alaska X 88X3310 10Gigabit PHY support")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reported-by: Russell King <linux@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'powerpc-5.0-6' of git://git./linux/kernel/git/powerpc/linux

Pull powerpc fix from Michael Ellerman:
"One fix for an oops when using SRIOV, introduced by the recent changes
  to support compound IOMMU groups.

  Thanks to Alexey Kardashevskiy"

* tag 'powerpc-5.0-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/powernv/sriov: Register IOMMU groups for VFs

Merge tag 'scsi-fixes' of git://git./linux/kernel/git/jejb/scsi

Pull SCSI fixes from James Bottomley:
"Four small fixes: three in drivers and one in the core.

  The core fix is also minor in scope since the bug it fixes is only
  known to affect systems using SCSI reservations. Of the driver bugs,
  the libsas one is the most major because it can lead to multiple disks
  on the same expander not being exposed"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: core: reset host byte in DID_NEXUS_FAILURE case
  scsi: libsas: Fix rphy phy_identifier for PHYs with end devices attached
  scsi: sd_zbc: Fix sd_zbc_report_zones() buffer allocation
  scsi: libiscsi: Fix race between iscsi_xmit_task and iscsi_complete_task

Merge git://git./pub/scm/linux/kernel/git/bpf/bpf

Daniel Borkmann says:

====================
pull-request: bpf 2019-02-23

The following pull-request contains BPF updates for your *net* tree.

The main changes are:

1) Fix a bug in BPF's LPM deletion logic to match correct prefix
   length, from Alban.

2) Fix AF_XDP teardown by not destroying umem prematurely as it
   is still needed till all outstanding skbs are freed, from Björn.

3) Fix unkillable BPF_PROG_TEST_RUN under preempt kernel by checking
   signal_pending() outside need_resched() condition which is never
   triggered there, from Stanislav.

4) Fix two nfp JIT bugs, one in code emission for K-based xor, and
   another one to explicitly clear upper bits in alu32, from Jiong.

5) Add bpf list address to maintainers file, from Daniel.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'fixes-v5.0-rc7' of git://git./linux/kernel/git/jmorris/linux-security

Pull keys fixes from James Morris:
"Two fixes from Eric Biggers"

* 'fixes-v5.0-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
KEYS: always initialize keyring_index_key::desc_len
KEYS: user: Align the payload buffer

Merge tag 'pm-5.0' of git://git./linux/kernel/git/rafael/linux-pm

Pull power management fixes from Rafael Wysocki:
"These fix a regression in the PM-runtime framework introduced by the
  recent switch-over of it to using hrtimers and a use-after-free
  introduced by one of the recent changes in the scmi-cpufreq driver.

  Specifics:

   - Use hrtimer_try_to_cancel() instead of hrtimer_cancel() in the
     PM-runtime framework to avoid a possible timer-related deadlock
     introduced recently (Vincent Guittot).

   - Reorder the scmi-cpufreq driver code to avoid accessing memory that
     has just been freed (Yangtao Li)"

* tag 'pm-5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  PM-runtime: Fix deadlock when canceling hrtimer
  cpufreq: scmi: Fix use-after-free in scmi_cpufreq_exit()

Merge tag 'armsoc-fixes' of git://git./linux/kernel/git/soc/soc

Pull ARM SoC fixes from Arnd Bergmann:
"Only a handful of device tree fixes, all simple enough:

  NVIDIA Tegra:
   - Fix a regression for booting on chromebooks

  TI OMAP:
   - Two fixes PHY mode on am335x reference boards

  Marvell mvebu:
   - A regression fix for Armada XP NAND flash controllers
   - An incorrect reset signal on the clearfog board"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
  ARM: tegra: Restore DT ABI on Tegra124 Chromebooks
  ARM: dts: am335x-evm: Fix PHY mode for ethernet
  ARM: dts: am335x-evmsk: Fix PHY mode for ethernet
  arm64: dts: clearfog-gt-8k: fix SGMII PHY reset signal
  ARM: dts: armada-xp: fix Armada XP boards NAND description

Merge tag 'arc-5.0-final' of git://git./linux/kernel/git/vgupta/arc

Pull ARC fixes from Vineet Gupta:
"Fixes for ARC for 5.0, bunch of those are stable fodder anyways so
  sooner the better.

   - Fix memcpy to prevent prefetchw beyond end of buffer [Eugeniy]

   - Enable unaligned access early to prevent exceptions given newer gcc
     code gen [Eugeniy]

   - Tighten up uboot arg checking to prevent false negatives and also
     allow both jtag and bootloading to coexist w/o config option as
     needed by kernelCi folks [Eugeniy]

   - Set slab alignment to 8 for ARC to avoid the atomic64_t unalign
     [Alexey]

   - Disable regfile auto save on interrupts on HSDK platform due to a
     silicon issue [Vineet]

   - Avoid HS38x boot printing crash by not reading HS48x only reg
     [Vineet]"

* tag 'arc-5.0-final' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
  ARCv2: don't assume core 0x54 has dual issue
  ARC: define ARCH_SLAB_MINALIGN = 8
  ARC: enable uboot support unconditionally
  ARC: U-boot: check arguments paranoidly
  ARCv2: support manual regfile save on interrupts
  ARC: uacces: remove lp_start, lp_end from clobber list
  ARC: fix actionpoints configuration detection
  ARCv2: lib: memcpy: fix doing prefetchw outside of buffer
  ARCv2: Enable unaligned access in early ASM code

bpf, doc: add bpf list as secondary entry to maintainers file

We recently created a bpf@vger.kernel.org list (https://lore.kernel.org/bpf/)
for BPF related discussions, originally in context of BPF track at LSF/MM
for topic discussions. It's *optional* but *desirable* to keep it in Cc for
BPF related kernel/loader/llvm/tooling threads, meaning also infrastructure
like llvm that sits on top of kernel but is crucial to BPF. In any case,
netdev with it's bpf delegate is *as-is* today primary list for patches, so
nothing changes in the workflow. Main purpose is to have some more awareness
for the bpf@vger.kernel.org list that folks can Cc for BPF specific topics.

Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

Merge branch 'parisc-5.0-1' of git://git./linux/kernel/git/deller/parisc-linux

Pull parisc fixes from Helge Deller:
"Fix ptrace syscall number modification which has been broken since
  kernel v4.5 and provide alternative email addresses for the remaining
  users of the retired parisc-linux.org email domain"

* 'parisc-5.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  CREDITS/MAINTAINERS: Retire parisc-linux.org email domain
  parisc: Fix ptrace syscall number modification

Merge tag 'kbuild-fixes-v5.0-2' of git://git./linux/kernel/git/masahiroy/linux-kbuild

Pull more Kbuild fixes from Masahiro Yamada:

- fix scripts/kallsyms.c to correctly check too long symbol names

- fix sh build error for the combination of CONFIG_OF_EARLY_FLATTREE=y
   and CONFIG_USE_BUILTIN_DTB=n

* tag 'kbuild-fixes-v5.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  sh: fix build error for invisible CONFIG_BUILTIN_DTB_SOURCE
  kallsyms: Handle too long symbols in kallsyms.c

Merge branch 'udp-a-few-fixes'

Paolo Abeni says:

====================
udp: a few fixes

This series includes some UDP-related fixlet. All this stuff has been
pointed out by the sparse tool. The first two patches are just annotation
related, while the last 2 cover some very unlikely races.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

udp: fix possible user after free in error handler

Similar to the previous commit, this addresses the same issue for
ipv4: use a single fetch operation and use the correct rcu
annotation.

Fixes: e7cc082455cb ("udp: Support for error handlers of tunnels with arbitrary destination port")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

udpv6: fix possible user after free in error handler

Before derefencing the encap pointer, commit e7cc082455cb ("udp: Support
for error handlers of tunnels with arbitrary destination port") checks
for a NULL value, but the two fetch operation can race with removal.
Fix the above using a single access.
Also fix a couple of type annotations, to make sparse happy.

Fixes: e7cc082455cb ("udp: Support for error handlers of tunnels with arbitrary destination port")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

fou6: fix proto error handler argument type

Last argument of gue6_err_proto_handler() has a wrong type annotation,
fix it and make sparse happy again.

Fixes: b8a51b38e4d4 ("fou, fou6: ICMP error handlers for FoU and GUE")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

udpv6: add the required annotation to mib type

In commit 029a37434880 ("udp6: cleanup stats accounting in recvmsg()")
I forgot to add the percpu annotation for the mib pointer. Add it, and
make sparse happy.

Fixes: 029a37434880 ("udp6: cleanup stats accounting in recvmsg()")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mdio_bus: Fix use-after-free on device_register fails

KASAN has found use-after-free in fixed_mdio_bus_init,
commit 0c692d07842a ("drivers/net/phy/mdio_bus.c: call
put_device on device_register() failure") call put_device()
while device_register() fails,give up the last reference
to the device and allow mdiobus_release to be executed
,kfreeing the bus. However in most drives, mdiobus_free
be called to free the bus while mdiobus_register fails.
use-after-free occurs when access bus again, this patch
revert it to let mdiobus_free free the bus.

KASAN report details as below:

BUG: KASAN: use-after-free in mdiobus_free+0x85/0x90 drivers/net/phy/mdio_bus.c:482
Read of size 4 at addr ffff8881dc824d78 by task syz-executor.0/3524

CPU: 1 PID: 3524 Comm: syz-executor.0 Not tainted 5.0.0-rc7+ #45
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0xfa/0x1ce lib/dump_stack.c:113
print_address_description+0x65/0x270 mm/kasan/report.c:187
kasan_report+0x149/0x18d mm/kasan/report.c:317
mdiobus_free+0x85/0x90 drivers/net/phy/mdio_bus.c:482
fixed_mdio_bus_init+0x283/0x1000 [fixed_phy]
? 0xffffffffc0e40000
? 0xffffffffc0e40000
? 0xffffffffc0e40000
do_one_initcall+0xfa/0x5ca init/main.c:887
do_init_module+0x204/0x5f6 kernel/module.c:3460
load_module+0x66b2/0x8570 kernel/module.c:3808
__do_sys_finit_module+0x238/0x2a0 kernel/module.c:3902
do_syscall_64+0x147/0x600 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x462e99
Code: f7 d8 64 89 02 b8 ff ff ff ff c3 66 0f 1f 44 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 bc ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007f6215c19c58 EFLAGS: 00000246 ORIG_RAX: 0000000000000139
RAX: ffffffffffffffda RBX: 000000000073bf00 RCX: 0000000000462e99
RDX: 0000000000000000 RSI: 0000000020000080 RDI: 0000000000000003
RBP: 00007f6215c19c70 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00007f6215c1a6bc
R13: 00000000004bcefb R14: 00000000006f7030 R15: 0000000000000004

Allocated by task 3524:
set_track mm/kasan/common.c:85 [inline]
__kasan_kmalloc.constprop.3+0xa0/0xd0 mm/kasan/common.c:496
kmalloc include/linux/slab.h:545 [inline]
kzalloc include/linux/slab.h:740 [inline]
mdiobus_alloc_size+0x54/0x1b0 drivers/net/phy/mdio_bus.c:143
fixed_mdio_bus_init+0x163/0x1000 [fixed_phy]
do_one_initcall+0xfa/0x5ca init/main.c:887
do_init_module+0x204/0x5f6 kernel/module.c:3460
load_module+0x66b2/0x8570 kernel/module.c:3808
__do_sys_finit_module+0x238/0x2a0 kernel/module.c:3902
do_syscall_64+0x147/0x600 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe

Freed by task 3524:
set_track mm/kasan/common.c:85 [inline]
__kasan_slab_free+0x130/0x180 mm/kasan/common.c:458
slab_free_hook mm/slub.c:1409 [inline]
slab_free_freelist_hook mm/slub.c:1436 [inline]
slab_free mm/slub.c:2986 [inline]
kfree+0xe1/0x270 mm/slub.c:3938
device_release+0x78/0x200 drivers/base/core.c:919
kobject_cleanup lib/kobject.c:662 [inline]
kobject_release lib/kobject.c:691 [inline]
kref_put include/linux/kref.h:67 [inline]
kobject_put+0x146/0x240 lib/kobject.c:708
put_device+0x1c/0x30 drivers/base/core.c:2060
__mdiobus_register+0x483/0x560 drivers/net/phy/mdio_bus.c:382
fixed_mdio_bus_init+0x26b/0x1000 [fixed_phy]
do_one_initcall+0xfa/0x5ca init/main.c:887
do_init_module+0x204/0x5f6 kernel/module.c:3460
load_module+0x66b2/0x8570 kernel/module.c:3808
__do_sys_finit_module+0x238/0x2a0 kernel/module.c:3902
do_syscall_64+0x147/0x600 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe

The buggy address belongs to the object at ffff8881dc824c80
which belongs to the cache kmalloc-2k of size 2048
The buggy address is located 248 bytes inside of
2048-byte region [ffff8881dc824c80, ffff8881dc825480)
The buggy address belongs to the page:
page:ffffea0007720800 count:1 mapcount:0 mapping:ffff8881f6c02800 index:0x0 compound_mapcount: 0
flags: 0x2fffc0000010200(slab|head)
raw: 02fffc0000010200 0000000000000000 0000000500000001 ffff8881f6c02800
raw: 0000000000000000 00000000800f000f 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected

Memory state around the buggy address:
ffff8881dc824c00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff8881dc824c80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
>ffff8881dc824d00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^
ffff8881dc824d80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff8881dc824e00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb

Fixes: 0c692d07842a ("drivers/net/phy/mdio_bus.c: call put_device on device_register() failure")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: Set rtm_table to RT_TABLE_COMPAT for ipv6 for tables > 255

Set rtm_table to RT_TABLE_COMPAT for ipv6 for tables > 255 to
keep legacy software happy. This is similar to what was done for
ipv4 in commit 709772e6e065 ("net: Fix routing tables with
id > 255 for legacy software").

Signed-off-by: Kalash Nainwal <kalash@arista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'bnxt_en-firmware-message-delay-fixes'

Michael Chan says:

====================
bnxt_en: firmware message delay fixes.

We were seeing some intermittent firmware message timeouts in our lab and
these 2 small patches fix them. Please apply to stable as well. Thanks.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Wait longer for the firmware message response to complete.

The code waits up to 20 usec for the firmware response to complete
once we've seen the valid response header in the buffer. It turns
out that in some scenarios, this wait time is not long enough.
Extend it to 150 usec and use usleep_range() instead of udelay().

Fixes: 9751e8e71487 ("bnxt_en: reduce timeout on initial HWRM calls")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Fix typo in firmware message timeout logic.

The logic that polls for the firmware message response uses a shorter
sleep interval for the first few passes.  But there was a typo so it
was using the wrong counter (larger counter) for these short sleep
passes.  The result is a slightly shorter timeout period for these
firmware messages than intended.  Fix it by using the proper counter.

Fixes: 9751e8e71487 ("bnxt_en: reduce timeout on initial HWRM calls")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'bpf-nfp-codegen-fixes'

Jiong Wang says:

====================
Code-gen for BPF_ALU | BPF_XOR | BPF_K is wrong when imm is -1,
also high 32-bit of 64-bit register should always be cleared.

This set fixed both bugs.
====================

Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

nfp: bpf: fix ALU32 high bits clearance bug

NFP BPF JIT compiler is doing a couple of small optimizations when jitting
ALU imm instructions, some of these optimizations could save code-gen, for
example:

  A & -1 =  A
  A |  0 =  A
  A ^  0 =  A

However, for ALU32, high 32-bit of the 64-bit register should still be
cleared according to ISA semantics.

Fixes: cd7df56ed3e6 ("nfp: add BPF to NFP code translator")
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

nfp: bpf: fix code-gen bug on BPF_ALU | BPF_XOR | BPF_K

The intended optimization should be A ^ 0 = A, not A ^ -1 = A.

Fixes: cd7df56ed3e6 ("nfp: add BPF to NFP code translator")
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

Merge tag 'mac80211-for-davem-2019-02-22' of git://git./linux/kernel/git/jberg/mac80211

Johannes Berg says:

====================
Three more fixes:
* mac80211 mesh code wasn't allocating SKB tailroom properly
in some cases
* tx_sk_pacing_shift should be 7 for better performance
* mac80211_hwsim wasn't propagating genlmsg_reply() errors
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

Documentation: networking: switchdev: Update port parent ID section

Update the section about switchdev drivers having to implement a
switchdev_port_attr_get() function to return
SWITCHDEV_ATTR_ID_PORT_PARENT_ID since that is no longer valid after
commit bccb30254a4a ("net: Get rid of
SWITCHDEV_ATTR_ID_PORT_PARENT_ID").

Fixes: bccb30254a4a ("net: Get rid of SWITCHDEV_ATTR_ID_PORT_PARENT_ID")
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: socket: add check for negative optlen in compat setsockopt

__sys_setsockopt() already checks for `optlen < 0`. Add an equivalent check
to the compat path for robustness. This has to be `> INT_MAX` instead of
`< 0` because the signedness of `optlen` is different here.

Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv6: route: purge exception on removal

When a netdevice is unregistered, we flush the relevant exception
via rt6_sync_down_dev() -> fib6_ifdown() -> fib6_del() -> fib6_del_route().

Finally, we end-up calling rt6_remove_exception(), where we release
the relevant dst, while we keep the references to the related fib6_info and
dev. Such references should be released later when the dst will be
destroyed.

There are a number of caches that can keep the exception around for an
unlimited amount of time - namely dst_cache, possibly even socket cache.
As a result device registration may hang, as demonstrated by this script:

ip netns add cl
ip netns add rt
ip netns add srv
ip netns exec rt sysctl -w net.ipv6.conf.all.forwarding=1

ip link add name cl_veth type veth peer name cl_rt_veth
ip link set dev cl_veth netns cl
ip -n cl link set dev cl_veth up
ip -n cl addr add dev cl_veth 2001::2/64
ip -n cl route add default via 2001::1

ip -n cl link add tunv6 type ip6tnl mode ip6ip6 local 2001::2 remote 2002::1 hoplimit 64 dev cl_veth
ip -n cl link set tunv6 up
ip -n cl addr add 2013::2/64 dev tunv6

ip link set dev cl_rt_veth netns rt
ip -n rt link set dev cl_rt_veth up
ip -n rt addr add dev cl_rt_veth 2001::1/64

ip link add name rt_srv_veth type veth peer name srv_veth
ip link set dev srv_veth netns srv
ip -n srv link set dev srv_veth up
ip -n srv addr add dev srv_veth 2002::1/64
ip -n srv route add default via 2002::2

ip -n srv link add tunv6 type ip6tnl mode ip6ip6 local 2002::1 remote 2001::2 hoplimit 64 dev srv_veth
ip -n srv link set tunv6 up
ip -n srv addr add 2013::1/64 dev tunv6

ip link set dev rt_srv_veth netns rt
ip -n rt link set dev rt_srv_veth up
ip -n rt addr add dev rt_srv_veth 2002::2/64

ip netns exec srv netserver & sleep 0.1
ip netns exec cl ping6 -c 4 2013::1
ip netns exec cl netperf -H 2013::1 -t TCP_STREAM -l 3 & sleep 1
ip -n rt link set dev rt_srv_veth mtu 1400
wait %2

ip -n cl link del cl_veth

This commit addresses the issue purging all the references held by the
exception at time, as we currently do for e.g. ipv6 pcpu dst entries.

v1 -> v2:
- re-order the code to avoid accessing dst and net after dst_dev_put()

Fixes: 93531c674315 ("net/ipv6: separate handling of FIB entries from dst based routes")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'nic-thunderx-fix-communication-races-between-VF-PF'

Vadim Lomovtsev says:

====================
nic: thunderx: fix communication races between VF & PF

The ThunderX CN88XX NIC Virtual Function driver uses mailbox interface
to communicate to physical function driver. Each of VF has it's own pair
of mailbox registers to read from and write to. The mailbox registers
has no protection from possible races, so it has to be implemented
at software side.

After long term testing by loop of 'ip link set <ifname> up/down'
command it was found that there are two possible scenarios when
race condition appears:
1. VF receives link change message from PF and VF send RX mode
configuration message to PF in the same time from separate thread.
2. PF receives RX mode configuration from VF and in the same time,
in separate thread PF detects link status change and sends appropriate
message to particular VF.

Both cases leads to mailbox data to be rewritten, NIC VF messaging control
data to be updated incorrectly and communication sequence gets broken.

This patch series is to address race condition with VF & PF communication.

Changes:
v1 -> v2
- 0000: correct typo in cover letter subject: 'betwen' -> 'between';
- move link state polling request task from pf to vf
   instead of cheking status of mailbox irq;
v2 -> v3
- 0003: change return type of nicvf_send_cfg_done() function
   from int to void;
- 0007: update subject and remove unused variable 'netdev'
   from nicvf_link_status_check_task() function;
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

net: thunderx: remove link change polling code and info from nicpf

Since link change polling routine was moved to nicvf side,
we don't need anymore polling function at nicpf side along
with link status info for all enabled Vfs as at VF side
this info is already tracked.

This commit is to remove unnecessary code & fields from
nicpf structure.

Signed-off-by: Vadim Lomovtsev <vlomovtsev@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: thunderx: move link state polling function to VF

Move the link change polling task to VF side in order to
prevent races between VF and PF while sending link change
message(s). This commit is to implement link change request
to be initiated by VF.

Signed-off-by: Vadim Lomovtsev <vlomovtsev@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: thunderx: add mutex to protect mailbox from concurrent calls for same VF

In some cases it could happen that nicvf_send_msg_to_pf() could be called
concurrently for the same NIC VF, and thus re-writing mailbox contents and
breaking messaging sequence with PF by re-writing NICVF data.

This commit is to implement mutex for NICVF to protect mailbox registers
and NICVF messaging control data from concurrent access.

Signed-off-by: Vadim Lomovtsev <vlomovtsev@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: thunderx: rework xcast message structure to make it fit into 64 bit

To communicate to PF each of ThunderX NIC VF uses mailbox which is
pair of 64 bit registers available to both VFn and PF.

This commit is to change the xcast message structure in order to
fit it into 64 bit.

Signed-off-by: Vadim Lomovtsev <vlomovtsev@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: thunderx: add nicvf_send_msg_to_pf result check for set_rx_mode_task

The rx_set_mode invokes number of messages to be send to PF for receive
mode configuration. In case if there any issues we need to stop sending
messages and release allocated memory.

This commit is to implement check of nicvf_msg_send_to_pf() result.

Signed-off-by: Vadim Lomovtsev <vlomovtsev@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: thunderx: make CFG_DONE message to run through generic send-ack sequence

At the end of NIC VF initialization VF sends CFG_DONE message to PF without
using nicvf_msg_send_to_pf routine. This potentially could re-write data in
mailbox. This commit is to implement common way of sending CFG_DONE message
by the same way with other configuration messages by using
nicvf_send_msg_to_pf() routine.

Signed-off-by: Vadim Lomovtsev <vlomovtsev@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: thunderx: replace global nicvf_rx_mode_wq work queue for all VFs to private for each of them.

Having one work queue for receive mode configuration ndo_set_rx_mode()
call for all VFs results in making each of them wait till the
set_rx_mode() call completes for another VF if any of close, set
receive mode and change flags calls being already invoked. Potentially
this could cause device state change before appropriate call of receive
mode configuration completes, so the call itself became meaningless,
corrupt data or break configuration sequence.

We don't need any delays in NIC VF configuration sequence so having delayed
work call with 0 delay has no sense.

This commit is to implement one work queue for each NIC VF for set_rx_mode
task and to let them work independently and replacing delayed_work
with work_struct.

Signed-off-by: Vadim Lomovtsev <vlomovtsev@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: thunderx: correct typo in macro name

Correct STREERING to STEERING at macro name for BGX steering register.

Signed-off-by: Vadim Lomovtsev <vlomovtsev@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ip6_gre: fix possible NULL pointer dereference in ip6erspan_set_version

Fix a possible NULL pointer dereference in ip6erspan_set_version checking
nlattr data pointer

kasan: CONFIG_KASAN_INLINE enabled
kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] PREEMPT SMP KASAN
CPU: 1 PID: 7549 Comm: syz-executor432 Not tainted 5.0.0-rc6-next-20190218
#37
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
RIP: 0010:ip6erspan_set_version+0x5c/0x350 net/ipv6/ip6_gre.c:1726
Code: 07 38 d0 7f 08 84 c0 0f 85 9f 02 00 00 49 8d bc 24 b0 00 00 00 c6 43
54 01 48 b8 00 00 00 00 00 fc ff df 48 89 fa 48 c1 ea 03 <80> 3c 02 00 0f
85 9a 02 00 00 4d 8b ac 24 b0 00 00 00 4d 85 ed 0f
RSP: 0018:ffff888089ed7168 EFLAGS: 00010202
RAX: dffffc0000000000 RBX: ffff8880869d6e58 RCX: 0000000000000000
RDX: 0000000000000016 RSI: ffffffff862736b4 RDI: 00000000000000b0
RBP: ffff888089ed7180 R08: 1ffff11010d3adcb R09: ffff8880869d6e58
R10: ffffed1010d3add5 R11: ffff8880869d6eaf R12: 0000000000000000
R13: ffffffff8931f8c0 R14: ffffffff862825d0 R15: ffff8880869d6e58
FS:  0000000000b3d880(0000) GS:ffff8880ae900000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000020000184 CR3: 0000000092cc5000 CR4: 00000000001406e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
  ip6erspan_newlink+0x66/0x7b0 net/ipv6/ip6_gre.c:2210
  __rtnl_newlink+0x107b/0x16c0 net/core/rtnetlink.c:3176
  rtnl_newlink+0x69/0xa0 net/core/rtnetlink.c:3234
  rtnetlink_rcv_msg+0x465/0xb00 net/core/rtnetlink.c:5192
  netlink_rcv_skb+0x17a/0x460 net/netlink/af_netlink.c:2485
  rtnetlink_rcv+0x1d/0x30 net/core/rtnetlink.c:5210
  netlink_unicast_kernel net/netlink/af_netlink.c:1310 [inline]
  netlink_unicast+0x536/0x720 net/netlink/af_netlink.c:1336
  netlink_sendmsg+0x8ae/0xd70 net/netlink/af_netlink.c:1925
  sock_sendmsg_nosec net/socket.c:621 [inline]
  sock_sendmsg+0xdd/0x130 net/socket.c:631
  ___sys_sendmsg+0x806/0x930 net/socket.c:2136
  __sys_sendmsg+0x105/0x1d0 net/socket.c:2174
  __do_sys_sendmsg net/socket.c:2183 [inline]
  __se_sys_sendmsg net/socket.c:2181 [inline]
  __x64_sys_sendmsg+0x78/0xb0 net/socket.c:2181
  do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290
  entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x440159
Code: 18 89 d0 c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 00 48 89 f8 48 89 f7
48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff
ff 0f 83 fb 13 fc ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007fffa69156e8 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 00000000004002c8 RCX: 0000000000440159
RDX: 0000000000000000 RSI: 0000000020001340 RDI: 0000000000000003
RBP: 00000000006ca018 R08: 0000000000000001 R09: 00000000004002c8
R10: 0000000000000011 R11: 0000000000000246 R12: 00000000004019e0
R13: 0000000000401a70 R14: 0000000000000000 R15: 0000000000000000
Modules linked in:
---[ end trace 09f8a7d13b4faaa1 ]---
RIP: 0010:ip6erspan_set_version+0x5c/0x350 net/ipv6/ip6_gre.c:1726
Code: 07 38 d0 7f 08 84 c0 0f 85 9f 02 00 00 49 8d bc 24 b0 00 00 00 c6 43
54 01 48 b8 00 00 00 00 00 fc ff df 48 89 fa 48 c1 ea 03 <80> 3c 02 00 0f
85 9a 02 00 00 4d 8b ac 24 b0 00 00 00 4d 85 ed 0f
RSP: 0018:ffff888089ed7168 EFLAGS: 00010202
RAX: dffffc0000000000 RBX: ffff8880869d6e58 RCX: 0000000000000000
RDX: 0000000000000016 RSI: ffffffff862736b4 RDI: 00000000000000b0
RBP: ffff888089ed7180 R08: 1ffff11010d3adcb R09: ffff8880869d6e58
R10: ffffed1010d3add5 R11: ffff8880869d6eaf R12: 0000000000000000
R13: ffffffff8931f8c0 R14: ffffffff862825d0 R15: ffff8880869d6e58
FS:  0000000000b3d880(0000) GS:ffff8880ae900000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000020000184 CR3: 0000000092cc5000 CR4: 00000000001406e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400

Fixes: 4974d5f678ab ("net: ip6_gre: initialize erspan_ver just for erspan tunnels")
Reported-and-tested-by: syzbot+30191cf1057abd3064af@syzkaller.appspotmail.com
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Reviewed-by: Greg Rose <gvrose8192@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

team: use operstate consistently for linkup

When a port is added to a team, its initial state is derived
from netif_carrier_ok rather than netif_oper_up.
If it is carrier up but operationally down at the time of being
added, the port state.linkup will be set prematurely.
port state.linkup should be set consistently using
netif_oper_up rather than netif_carrier_ok.

Fixes: f1d22a1e0595 ("team: account for oper state")
Signed-off-by: George Wilkie <gwilkie@vyatta.att-mail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

r8152: Fix an error on RTL8153-BD MAC Address Passthrough support

RTL8153-BD is used in Dell DA300 type-C dongle.
Added RTL8153-BD support to activate MAC address pass through on DA300.
Apply correction on previously submitted patch in net.git tree.

Signed-off-by: David Chen <david.chen7@dell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipvlan: disallow userns cap_net_admin to change global mode/flags

When running Docker with userns isolation e.g. --userns-remap="default"
and spawning up some containers with CAP_NET_ADMIN under this realm, I
noticed that link changes on ipvlan slave device inside that container
can affect all devices from this ipvlan group which are in other net
namespaces where the container should have no permission to make changes
to, such as the init netns, for example.

This effectively allows to undo ipvlan private mode and switch globally to
bridge mode where slaves can communicate directly without going through
hostns, or it allows to switch between global operation mode (l2/l3/l3s)
for everyone bound to the given ipvlan master device. libnetwork plugin
here is creating an ipvlan master and ipvlan slave in hostns and a slave
each that is moved into the container's netns upon creation event.

* In hostns:

  # ip -d a
  [...]
  8: cilium_host@bond0: <BROADCAST,MULTICAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default qlen 1000
     link/ether 0c:c4:7a:e1:3d:cc brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 68 maxmtu 65535
     ipvlan  mode l3 bridge numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535
     inet 10.41.0.1/32 scope link cilium_host
       valid_lft forever preferred_lft forever
  [...]

* Spawn container & change ipvlan mode setting inside of it:

  # docker run -dt --cap-add=NET_ADMIN --network cilium-net --name client -l app=test cilium/netperf
  9fff485d69dcb5ce37c9e33ca20a11ccafc236d690105aadbfb77e4f4170879c

  # docker exec -ti client ip -d a
  [...]
  10: cilium0@if4: <BROADCAST,MULTICAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default qlen 1000
      link/ether 0c:c4:7a:e1:3d:cc brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 68 maxmtu 65535
      ipvlan  mode l3 bridge numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535
      inet 10.41.197.43/32 brd 10.41.197.43 scope global cilium0
         valid_lft forever preferred_lft forever

  # docker exec -ti client ip link change link cilium0 name cilium0 type ipvlan mode l2

  # docker exec -ti client ip -d a
  [...]
  10: cilium0@if4: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default qlen 1000
      link/ether 0c:c4:7a:e1:3d:cc brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 68 maxmtu 65535
      ipvlan  mode l2 bridge numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535
      inet 10.41.197.43/32 brd 10.41.197.43 scope global cilium0
         valid_lft forever preferred_lft forever

* In hostns (mode switched to l2):

  # ip -d a
  [...]
  8: cilium_host@bond0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default qlen 1000
      link/ether 0c:c4:7a:e1:3d:cc brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 68 maxmtu 65535
      ipvlan  mode l2 bridge numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535
      inet 10.41.0.1/32 scope link cilium_host
         valid_lft forever preferred_lft forever
  [...]

Same l3 -> l2 switch would also happen by creating another slave inside
the container's network namespace when specifying the existing cilium0
link to derive the actual (bond0) master:

  # docker exec -ti client ip link add link cilium0 name cilium1 type ipvlan mode l2

  # docker exec -ti client ip -d a
  [...]
  2: cilium1@if4: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000
      link/ether 0c:c4:7a:e1:3d:cc brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 68 maxmtu 65535
      ipvlan  mode l2 bridge numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535
  10: cilium0@if4: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default qlen 1000
      link/ether 0c:c4:7a:e1:3d:cc brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 68 maxmtu 65535
      ipvlan  mode l2 bridge numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535
      inet 10.41.197.43/32 brd 10.41.197.43 scope global cilium0
         valid_lft forever preferred_lft forever

* In hostns:

  # ip -d a
  [...]
  8: cilium_host@bond0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default qlen 1000
      link/ether 0c:c4:7a:e1:3d:cc brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 68 maxmtu 65535
      ipvlan  mode l2 bridge numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535
      inet 10.41.0.1/32 scope link cilium_host
         valid_lft forever preferred_lft forever
  [...]

One way to mitigate it is to check CAP_NET_ADMIN permissions of
the ipvlan master device's ns, and only then allow to change
mode or flags for all devices bound to it. Above two cases are
then disallowed after the patch.

Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: don't compare hb_timer expire date before starting it

hb_timer might not start at all for a particular transport because its
start is conditional. In a result a node is not sending heartbeats.

Function sctp_transport_reset_hb_timer has two roles:
    - initial start of hb_timer for a given transport,
    - update expire date of hb_timer for a given transport.
The function is optimized to update timer's expire only if it is before
a new calculated one but this comparison is invalid for a timer which
has not yet started. Such a timer has expire == 0 and if a new expire
value is bigger than (MAX_JIFFIES / 2 + 2) then "time_before" macro will
fail and timer will not start resulting in no heartbeat packets send by
the node.

This was found when association was initialized within first 5 mins
after system boot due to jiffies init value which is near to MAX_JIFFIES.

Test kernel version: 4.9.154 (ARCH=arm)
hb_timer.expire = 0;                //initialized, not started timer
new_expire = MAX_JIFFIES / 2 + 2;   //or more
time_before(hb_timer.expire, new_expire) == false

Fixes: ba6f5e33bdbb ("sctp: avoid refreshing heartbeat timer too often")
Reported-by: Marcin Stojek <marcin.stojek@nokia.com>
Tested-by: Marcin Stojek <marcin.stojek@nokia.com>
Signed-off-by: Maciej Kwiecien <maciej.kwiecien@nokia.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'drm-fixes-2019-02-22' of git://anongit.freedesktop.org/drm/drm

Pull drm fixes from Dave Airlie:
"This contains a single i915 tiled display fix, and a set of
  amdgpu/radeon fixes.

  i915:

   - tiled display fix

  amdgpu/radeon:

   - runtime PM fix

   - bulk moves disable (fix is too large for 5.0)

   - a set of display fixes that are all cc'ed stable so we didn't want
     to leave them until -next"

* tag 'drm-fixes-2019-02-22' of git://anongit.freedesktop.org/drm/drm:
  drm/amdgpu: disable bulk moves for now
  drm/amd/display: set clocks to 0 on suspend on dce80
  drm/amd/display: fix optimize_bandwidth func pointer for dce80
  drm/amd/display: Fix negative cursor pos programming
  drm/i915/fbdev: Actually configure untiled displays
  drm/amd/display: Raise dispclk value for dce11
  drm/amd/display: Fix MST reboot/poweroff sequence
  drm/amdgpu: Update sdma golden setting for vega20
  drm/amdgpu: Set DPM_FLAG_NEVER_SKIP when enabling PM-runtime
  gpu: drm: radeon: Set DPM_FLAG_NEVER_SKIP when enabling PM-runtime

Merge tag 'for-linus' of git://git./linux/kernel/git/rdma/rdma

Pull rdma fixes from Jason Gunthorpe:
"Small set of three regression fixing patches, things are looking
  pretty good here.

   - Fix cxgb4 to work again with non-4k page sizes

   - NULL pointer oops in SRP during sg_reset"

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
  iw_cxgb4: cq/qp mask depends on bar2 pages in a host page
  cxgb4: Export sge_host_page_size to ulds
  RDMA/srp: Rework SCSI device reset handling

KVM: MMU: record maximum physical address width in kvm_mmu_extended_role

Previously, commit 7dcd57552008 ("x86/kvm/mmu: check if tdp/shadow
MMU reconfiguration is needed") offered some optimization to avoid
the unnecessary reconfiguration. Yet one scenario is broken - when
cpuid changes VM's maximum physical address width, reconfiguration
is needed to reset the reserved bits. Also, the TDP may need to
reset its shadow_root_level when this value is changed.

To fix this, a new field, maxphyaddr, is introduced in the extended
role structure to keep track of the configured guest physical address
width.

Signed-off-by: Yu Zhang <yu.c.zhang@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

kvm: x86: Return LA57 feature based on hardware capability

Previously, 'commit 372fddf70904 ("x86/mm: Introduce the 'no5lvl' kernel
parameter")' cleared X86_FEATURE_LA57 in boot_cpu_data, if Linux chooses
to not run in 5-level paging mode. Yet boot_cpu_data is queried by
do_cpuid_ent() as the host capability later when creating vcpus, and Qemu
will not be able to detect this feature and create VMs with LA57 feature.

As discussed earlier, VMs can still benefit from extended linear address
width, e.g. to enhance features like ASLR. So we would like to fix this,
by return the true hardware capability when Qemu queries.

Signed-off-by: Yu Zhang <yu.c.zhang@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

x86/kvm/mmu: fix switch between root and guest MMUs

Commit 14c07ad89f4d ("x86/kvm/mmu: introduce guest_mmu") brought one subtle
change: previously, when switching back from L2 to L1, we were resetting
MMU hooks (like mmu->get_cr3()) in kvm_init_mmu() called from
nested_vmx_load_cr3() and now we do that in nested_ept_uninit_mmu_context()
when we re-target vcpu->arch.mmu pointer.
The change itself looks logical: if nested_ept_init_mmu_context() changes
something than nested_ept_uninit_mmu_context() restores it back. There is,
however, one thing: the following call chain:

nested_vmx_load_cr3()
  kvm_mmu_new_cr3()
    __kvm_mmu_new_cr3()
      fast_cr3_switch()
        cached_root_available()

now happens with MMU hooks pointing to the new MMU (root MMU in our case)
while previously it was happening with the old one. cached_root_available()
tries to stash current root but it is incorrect to read current CR3 with
mmu->get_cr3(), we need to use old_mmu->get_cr3() which in case we're
switching from L2 to L1 is guest_mmu. (BTW, in shadow page tables case this
is a non-issue because we don't switch MMU).

While we could've tried to guess that we're switching between MMUs and call
the right ->get_cr3() from cached_root_available() this seems to be overly
complicated. Instead, just stash the corresponding CR3 when setting
root_hpa and make cached_root_available() use the stashed value.

Fixes: 14c07ad89f4d ("x86/kvm/mmu: introduce guest_mmu")
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

KEYS: always initialize keyring_index_key::desc_len

syzbot hit the 'BUG_ON(index_key->desc_len == 0);' in __key_link_begin()
called from construct_alloc_key() during sys_request_key(), because the
length of the key description was never calculated.

The problem is that we rely on ->desc_len being initialized by
search_process_keyrings(), specifically by search_nested_keyrings().
But, if the process isn't subscribed to any keyrings that never happens.

Fix it by always initializing keyring_index_key::desc_len as soon as the
description is set, like we already do in some places.

The following program reproduces the BUG_ON() when it's run as root and
no session keyring has been installed.  If it doesn't work, try removing
pam_keyinit.so from /etc/pam.d/login and rebooting.

    #include <stdlib.h>
    #include <unistd.h>
    #include <keyutils.h>

    int main(void)
    {
            int id = add_key("keyring", "syz", NULL, 0, KEY_SPEC_USER_KEYRING);

            keyctl_setperm(id, KEY_OTH_WRITE);
            setreuid(5000, 5000);
            request_key("user", "desc", "", id);
    }

Reported-by: syzbot+ec24e95ea483de0a24da@syzkaller.appspotmail.com
Fixes: b2a4df200d57 ("KEYS: Expand the capacity of a keyring")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: James Morris <james.morris@microsoft.com>

KEYS: user: Align the payload buffer

Align the payload of "user" and "logon" keys so that users of the
keyrings service can access it as a struct that requires more than
2-byte alignment. fscrypt currently does this which results in the read
of fscrypt_key::size being misaligned as it needs 4-byte alignment.

Align to __alignof__(u64) rather than __alignof__(long) since in the
future it's conceivable that people would use structs beginning with
u64, which on some platforms would require more than 'long' alignment.

Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Fixes: 2aa349f6e37c ("[PATCH] Keys: Export user-defined keyring operations")
Fixes: 88bd6ccdcdd6 ("ext4 crypto: add encryption key management facilities")
Cc: stable@vger.kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: James Morris <james.morris@microsoft.com>

Merge tag 'clk-fixes-for-linus' of git://git./linux/kernel/git/clk/linux

Pull clk fixes from Stephen Boyd:
"A few more fixes for clk drivers causing regressions this release.

  Two Allwinner index fixes for A31 and V3 and two Microchip AT91 fixes
  for an incorrect clk parent linkage and a miscalculated number of
  clks"

* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
  clk: at91: fix masterck name
  clk: at91: fix at91sam9x5 peripheral clock number
  clk: sunxi: A31: Fix wrong AHB gate number
  clk: sunxi-ng: v3s: Fix TCON reset de-assert bit

bpf, lpm: fix lookup bug in map_delete_elem

trie_delete_elem() was deleting an entry even though it was not matching
if the prefixlen was correct. This patch adds a check on matchlen.

Reproducer:

$ sudo bpftool map create /sys/fs/bpf/mylpm type lpm_trie key 8 value 1 entries 128 name mylpm flags 1
$ sudo bpftool map update pinned /sys/fs/bpf/mylpm key hex 10 00 00 00 aa bb cc dd value hex 01
$ sudo bpftool map dump pinned /sys/fs/bpf/mylpm
key: 10 00 00 00 aa bb cc dd value: 01
Found 1 element
$ sudo bpftool map delete pinned /sys/fs/bpf/mylpm key hex 10 00 00 00 ff ff ff ff
$ echo $?
0
$ sudo bpftool map dump pinned /sys/fs/bpf/mylpm
Found 0 elements

A similar reproducer is added in the selftests.

Without the patch:

$ sudo ./tools/testing/selftests/bpf/test_lpm_map
test_lpm_map: test_lpm_map.c:485: test_lpm_delete: Assertion `bpf_map_delete_elem(map_fd, key) == -1 && errno == ENOENT' failed.
Aborted

With the patch: test_lpm_map runs without errors.

Fixes: e454cf595853 ("bpf: Implement map_delete_elem for BPF_MAP_TYPE_LPM_TRIE")
Cc: Craig Gallek <kraig@google.com>
Signed-off-by: Alban Crequy <alban@kinvolk.io>
Acked-by: Craig Gallek <kraig@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

Merge tag 'mvebu-fixes-5.0-2' of git://git.infradead.org/linux-mvebu into arm/fixes

mvebu fixes for 5.0 (part 2)

Fix PHY reset signal on clearfog gt 8K (Armada 8040 based)
Fix NAND description on Armada XP boards which was broken since a few
release

* tag 'mvebu-fixes-5.0-2' of git://git.infradead.org/linux-mvebu:
arm64: dts: clearfog-gt-8k: fix SGMII PHY reset signal
ARM: dts: armada-xp: fix Armada XP boards NAND description

Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'omap-for-v5.0/fixes-rc7-signed' of git://git./linux/kernel/git/tmlind/linux-omap into arm/fixes

Two am335x ethernet phy mode fixes for v5.0-rc cycle

Recent changes with commit cd28d1d6e52e: ("net: phy: at803x: Disable phy
delay for RGMII mode") broke Ethernet on am335x-evmsk, and turns out some
device driver fixes are needed.

Even without the driver fixes, am335x needs to run in rgmii-id mode instead
rgmii-txid mode. Things have been working based on luck as the broken driver
has been configuring rgmii-id mode. Let's fix that as that way things work
as they're supposed to work from hardware wiring point of view.

* tag 'omap-for-v5.0/fixes-rc7-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am335x-evm: Fix PHY mode for ethernet
ARM: dts: am335x-evmsk: Fix PHY mode for ethernet

Signed-off-by: Arnd Bergmann <arnd@arndb.de>

mac80211: allocate tailroom for forwarded mesh packets

Forwarded packets enter the tx path through ieee80211_add_pending_skb,
which skips the ieee80211_skb_resize call.
Fixes WARN_ON in ccmp_encrypt_skb and resulting packet loss.

Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: Change default tx_sk_pacing_shift to 7

When we did the original tests for the optimal value of sk_pacing_shift, we
came up with 6 ms of buffering as the default. Sadly, 6 is not a power of
two, so when picking the shift value I erred on the size of less buffering
and picked 4 ms instead of 8. This was probably wrong; those 2 ms of extra
buffering makes a larger difference than I thought.

So, change the default pacing shift to 7, which corresponds to 8 ms of
buffering. The point of diminishing returns really kicks in after 8 ms, and
so having this as a default should cut down on the need for extensive
per-device testing and overrides needed in the drivers.

Cc: stable@vger.kernel.org
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211_hwsim: propagate genlmsg_reply return code

genlmsg_reply can fail, so propagate its return code

Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Merge branch 'pm-cpufreq-fixes'

* pm-cpufreq-fixes:
cpufreq: scmi: Fix use-after-free in scmi_cpufreq_exit()

phonet: fix building with clang

clang warns about overflowing the data[] member in the struct pnpipehdr:

net/phonet/pep.c:295:8: warning: array index 4 is past the end of the array (which contains 1 element) [-Warray-bounds]
                        if (hdr->data[4] == PEP_IND_READY)
                            ^         ~
include/net/phonet/pep.h:66:3: note: array 'data' declared here
                u8              data[1];

Using a flexible array member at the end of the struct avoids the
warning, but since we cannot have a flexible array member inside
of the union, each index now has to be moved back by one, which
makes it a little uglier.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Rémi Denis-Courmont <remi@remlab.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'master' of git://git./linux/kernel/git/klassert/ipsec

Steffen Klassert says:

====================
pull request (net): ipsec 2019-02-21

1) Don't do TX bytes accounting for the esp trailer when sending
   from a request socket as this will result in an out of bounds
   memory write. From Martin Willi.

2) Destroy xfrm_state synchronously on net exit path to
   avoid nested gc flush callbacks that may trigger a
   warning in xfrm6_tunnel_net_exit(). From Cong Wang.

3) Do an unconditionally clone in pfkey_broadcast_one()
   to avoid a race when freeing the skb.
   From Sean Tranchetti.

4) Fix inbound traffic via XFRM interfaces across network
   namespaces. We did the lookup for interfaces and policies
   in the wrong namespace. From Tobias Brunner.

Please pull or let me know if there are problems.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'report-erspan-version-field-just-for-erspan-tunnels'

Lorenzo Bianconi says:

====================
report erspan version field just for erspan tunnels

Do not report erspan_version to userpsace for non erspan tunnels.
Report IFLA_GRE_ERSPAN_INDEX only for erspan version 1 in
ip6gre_fill_info
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

net: ip6_gre: do not report erspan_ver for ip6gre or ip6gretap

Report erspan version field to userspace in ip6gre_fill_info just for
erspan_v6 tunnels. Moreover report IFLA_GRE_ERSPAN_INDEX only for
erspan version 1.
The issue can be triggered with the following reproducer:

$ip link add name gre6 type ip6gre local 2001::1 remote 2002::2
$ip link set gre6 up
$ip -d link sh gre6
14: grep6@NONE: <POINTOPOINT,NOARP,UP,LOWER_UP> mtu 1448 qdisc noqueue state UNKNOWN mode DEFAULT group default qlen 1000
link/gre6 2001::1 peer 2002::2 promiscuity 0 minmtu 0 maxmtu 0
ip6gre remote 2002::2 local 2001::1 hoplimit 64 encaplimit 4 tclass 0x00 flowlabel 0x00000 erspan_index 0 erspan_ver 0 addrgenmode eui64

Fixes: 94d7d8f29287 ("ip6_gre: add erspan v2 support")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ip_gre: do not report erspan_ver for gre or gretap

Report erspan version field to userspace in ipgre_fill_info just for
erspan tunnels. The issue can be triggered with the following reproducer:

$ip link add name gre1 type gre local 192.168.0.1 remote 192.168.1.1
$ip link set dev gre1 up
$ip -d link sh gre1
13: gre1@NONE: <POINTOPOINT,NOARP,UP,LOWER_UP> mtu 1476 qdisc noqueue state UNKNOWN mode DEFAULT group default qlen 1000
link/gre 192.168.0.1 peer 192.168.1.1 promiscuity 0 minmtu 0 maxmtu 0
gre remote 192.168.1.1 local 192.168.0.1 ttl inherit erspan_ver 0 addrgenmode eui64 numtxqueues 1 numrxqueues 1

Fixes: f551c91de262 ("net: erspan: introduce erspan v2 for ip_gre")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'drm-fixes-5.0' of git://people.freedesktop.org/~agd5f/linux into drm-fixes

A bit bigger than normal for this week due to fixes for some long
standing display issues that are bound for stable. These changes would
be going to stable anyway, so I figured it was better via 5.0 than 5.1.
- Several display fixes
- Fix PX systems due to core changes in runtime pm
- Disable bulk moves. They are fixed in 5.1, but fix is too invasive for 5.0

Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190220225715.3240-1-alexander.deucher@amd.com

ARCv2: don't assume core 0x54 has dual issue

The first release of core4 (0x54) was dual issue only (HS4x).
Newer releases allow hardware to be configured as single issue (HS3x)
or dual issue.

Prevent accessing a HS4x only aux register in HS3x, which otherwise
leads to illegal instruction exceptions

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

net: avoid false positives in untrusted gso validation

GSO packets with vnet_hdr must conform to a small set of gso_types.
The below commit uses flow dissection to drop packets that do not.

But it has false positives when the skb is not fully initialized.
Dissection needs skb->protocol and skb->network_header.

Infer skb->protocol from gso_type as the two must agree.
SKB_GSO_UDP can use both ipv4 and ipv6, so try both.

Exclude callers for which network header offset is not known.

Fixes: d5be7f632bad ("net: validate untrusted gso packets without csum offload")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'tipc-improvement-for-wait-and-wakeup'

Tung Nguyen says:

====================
tipc: improvement for wait and wakeup

Some improvements for tipc_wait_for_xzy().
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: improve function tipc_wait_for_rcvmsg()

This commit replaces schedule_timeout() with wait_woken()
in function tipc_wait_for_rcvmsg(). wait_woken() uses
memory barriers in its implementation to avoid potential
race condition when putting a process into sleeping state
and then waking it up.

Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: improve function tipc_wait_for_cond()

Commit 844cf763fba6 ("tipc: make macro tipc_wait_for_cond() smp safe")
replaced finish_wait() with remove_wait_queue() but still used
prepare_to_wait(). This causes unnecessary conditional
checking before adding to wait queue in prepare_to_wait().

This commit replaces prepare_to_wait() with add_wait_queue()
as the pair function with remove_wait_queue().

Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

bonding: fix PACKET_ORIGDEV regression

This patch fixes a subtle PACKET_ORIGDEV regression which was a side
effect of fixes introduced by:

6a9e461f6fe4 bonding: pass link-local packets to bonding master also.

... to:

b89f04c61efe bonding: deliver link-local packets with skb->dev set to link that packets arrived on

While 6a9e461f6fe4 restored pre-b89f04c61efe presence of link-local
packets on bonding masters (which is required e.g. by linux bridges
participating in spanning tree or needed for lab-like setups created
with group_fwd_mask) it also caused the originating device
information to be lost due to cloning.

Maciej Żenczykowski proposed another solution that doesn't require
packet cloning and retains original device information - instead of
returning RX_HANDLER_PASS for all link-local packets it's now limited
only to packets from inactive slaves.

At the same time, packets passed to bonding masters retain correct
information about the originating device and PACKET_ORIGDEV can be used
to determine it.

This elegantly solves all issues so far:

- link-local packets that were removed from bonding masters
- LLDP daemons being forced to explicitly bind to slave interfaces
- PACKET_ORIGDEV having no effect on bond interfaces

Fixes: 6a9e461f6fe4 (bonding: pass link-local packets to bonding master also.)
Reported-by: Vincent Bernat <vincent@bernat.ch>
Signed-off-by: Michal Soltys <soltys@ziu.info>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: vrf: remove MTU limits for vrf device

Similiar to commit e94cd8113ce63 ("net: remove MTU limits for dummy and
ifb device"), MTU is irrelevant for VRF device. We init it as 64K while
limit it to [68, 1500] may make users feel confused.

Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

MAINTAINERS: mark CAIF as orphan

The listed address for the CAIF maintainer bounces with
"553 5.3.0 <dmitry.tarnyagin@lockless.no>... No such user here", and the
only existing email address of the maintainer in git history hasn't
responded in a week.
Therefore, remove the listed maintainer and mark CAIF as orphan.

Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch '40GbE' of git://git./linux/kernel/git/jkirsher/net-queue

Jeff Kirsher says:

====================
Intel Wired LAN Driver Fixes 2019-02-21

This series contains fixes to ixgbe and i40e.

Majority of the fixes are to resolve XDP issues found in both drivers,
there is only one fix which is not XDP related. That one fix resolves
an issue seen on older 10GbE devices, where UDP traffic was either being
dropped or being transmitted out of order when the bit to enable L3/L4
filtering for transmit switched packets is enabled on older devices that
did not support this option.

Magnus fixes an XDP issue for both ixgbe and i40e, where receive rings
are created but no buffers are allocated for AF_XDP in zero-copy mode,
so no packets can be received and no interrupts will be generated so
that NAPI poll function that allocates buffers to the rings will never
get executed.

Björn fixes a race in XDP xmit ring cleanup for i40e, where
ndo_xdp_xmit() must be taken into consideration. Added a
synchronize_rcu() to wait for napi(s) before clearing the queue.

Jan fixes a ixgbe AF_XDP zero-copy transmit issue which can cause a
reset to be triggered, so add a check to ensure that netif carrier is
'ok' before trying to transmit packets.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

CREDITS/MAINTAINERS: Retire parisc-linux.org email domain

Retire the parisc-linux.org email domain and provide alternative email
addresses for the remaining users, as agreed upon with them.

Signed-off-by: Helge Deller <deller@gmx.de>