Linus Walleij [Thu, 10 Jan 2019 11:40:49 +0000 (12:40 +0100)]
drm/fb-helper: Scale back depth to supported maximum
The following happened when migrating an old fbdev driver to DRM:
The Integrator/CP PL111 supports 16BPP but only ARGB1555/ABGR1555
or XRGB1555/XBGR1555 i.e. the maximum depth is 15.
This makes the initialization of the framebuffer fail since
the code in drm_fb_helper_single_fb_probe() assigns the same value
to sizes.surface_bpp and sizes.surface_depth. I.e. it simply assumes
a 1-to-1 mapping between BPP and depth, which is true in most cases
but not for this hardware that only support odd formats.
To support the odd case of a driver supporting 16BPP with only 15
bits of depth, this patch will make the code loop over the formats
supported on the primary plane on each CRTC managed by the FB
helper and cap the depth to the maximum supported on any primary
plane.
On the PL110 Integrator, this makes drm_mode_legacy_fb_format()
select DRM_FORMAT_XRGB1555 which is acceptable for this driver, and
thus we get framebuffer, penguin and console on the Integrator/CP.
Cc: Noralf Trønnes <noralf@tronnes.org>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190110114049.10618-1-linus.walleij@linaro.org
Ville Syrjälä [Tue, 8 Jan 2019 17:28:28 +0000 (19:28 +0200)]
drm/edid: Add display_info.rgb_quant_range_selectable
Move the CEA-861 QS bit handling entirely into the edid code. No
need to bother the drivers with this.
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: "David (ChunMing) Zhou" <David1.Zhou@amd.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: Eric Anholt <eric@anholt.net> (supporter:DRM DRIVERS FOR VC4)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20190108172828.15184-4-ville.syrjala@linux.intel.com
Ville Syrjälä [Tue, 8 Jan 2019 17:28:27 +0000 (19:28 +0200)]
drm/radeon: Use drm_hdmi_avi_infoframe_quant_range()
Fill out the AVI infoframe quantization range bits using
drm_hdmi_avi_infoframe_quant_range() instead of hand rolling it.
This changes the behaviour slightly as
drm_hdmi_avi_infoframe_quant_range() will set a non-zero Q bit
even when QS==0 iff the Q bit matched the default quantization
range for the given mode. This matches the recommendation in
HDMI 2.0 and is allowed even before that.
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: "David (ChunMing) Zhou" <David1.Zhou@amd.com>
Cc: amd-gfx@lists.freedesktop.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190108172828.15184-3-ville.syrjala@linux.intel.com
Ville Syrjälä [Tue, 8 Jan 2019 17:28:26 +0000 (19:28 +0200)]
drm/i915: Use drm_hdmi_avi_infoframe_quant_range() for SDVO HDMI as well
Fill out the AVI infoframe quantization range bits using
drm_hdmi_avi_infoframe_quant_range() for SDVO HDMI encoder as well.
This changes the behaviour slightly as
drm_hdmi_avi_infoframe_quant_range() will set a non-zero Q bit
even when QS==0 iff the Q bit matched the default quantization
range for the given mode. This matches the recommendation in
HDMI 2.0 and is allowed even before that.
v2: Pimp commit msg (DK)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190108172828.15184-2-ville.syrjala@linux.intel.com
Ville Syrjälä [Tue, 8 Jan 2019 17:28:25 +0000 (19:28 +0200)]
drm/edid: Pass connector to AVI infoframe functions
Make life easier for drivers by simply passing the connector
to drm_hdmi_avi_infoframe_from_display_mode() and
drm_hdmi_avi_infoframe_quant_range(). That way drivers don't
need to worry about is_hdmi2_sink mess.
v2: Make is_hdmi2_sink() return true for sil-sii8620
Adapt to omap/vc4 changes
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: "David (ChunMing) Zhou" <David1.Zhou@amd.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: Seung-Woo Kim <sw0312.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: CK Hu <ck.hu@mediatek.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Sandy Huang <hjc@rock-chips.com>
Cc: "Heiko Stübner" <heiko@sntech.de>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Vincent Abriou <vincent.abriou@st.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Ilia Mirkin <imirkin@alum.mit.edu>
Cc: amd-gfx@lists.freedesktop.org
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Cc: nouveau@lists.freedesktop.org
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190108172828.15184-1-ville.syrjala@linux.intel.com
Daniel Vetter [Thu, 10 Jan 2019 10:30:45 +0000 (11:30 +0100)]
drm/crtc-helpers: WARN when used with atomic drivers
Motivated by an oversight of mine when looking at the atomic bochs
conversion. For consistency also switch over to the same style as used
elsewhere (e.g. in drm_mode_set_config_internal).
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190110103045.26821-1-daniel.vetter@ffwll.ch
Sam Ravnborg [Tue, 8 Jan 2019 19:29:39 +0000 (20:29 +0100)]
drm: remove drmP.h from drm_gem_cma_helper.h
With all dependencies fixed we can now remove
drmP.h from drm_gem_cma_helper.h.
It is replaced by the include files required,
or forward declarations as appropritate.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190108192939.15255-13-sam@ravnborg.org
Sam Ravnborg [Tue, 8 Jan 2019 19:29:38 +0000 (20:29 +0100)]
drm/tinydrm: do not reply on drmP.h from drm_gem_cma_helper.h
drmP.h was the only header file in the past and a lot
of files rely on that drmP.h defines everything.
The goal is to one day to delete drmP.h and
as a step towards this it will no longer be included in the
headers files in include/drm/
To prepare tinydrm/ for this add dependencies that
othwewise was pulled in by drmP.h from drm_gem_cma_helper.h
To avoid that tinydrm.h became "include everything",
push include files to the individual drivers.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: David Lechner <david@lechnology.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Eric Anholt <eric@anholt.net>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190108192939.15255-12-sam@ravnborg.org
Sam Ravnborg [Tue, 8 Jan 2019 19:29:36 +0000 (20:29 +0100)]
drm/arc: do not rely on drmP.h from drm_gem_cma_helper.h
drmP.h was the only header file in the past and a lot
of files rely on that drmP.h defines everything.
The goal is to one day to delete drmP.h and
as a step towards this it will no longer be included in the
headers files in include/drm/
To prepare arc/ for this add dependencies that
othwewise was pulled in by drmP.h from drm_gem_cma_helper.h
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: David Airlie <airlied@linux.ie>
[danvet: Fix typo in commit message.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190108192939.15255-10-sam@ravnborg.org
Sam Ravnborg [Tue, 8 Jan 2019 19:29:34 +0000 (20:29 +0100)]
drm: remove include of drmP.h from drm_encoder_slave.h
No further changes required.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190108192939.15255-8-sam@ravnborg.org
Sam Ravnborg [Tue, 8 Jan 2019 19:29:33 +0000 (20:29 +0100)]
drm: remove include of drmP.h from bridge/dw_hdmi.h
drmP.h is an relic from the days when there was a single header file.
To enable the removal of drmP.h from all users drop include
of drmP.h from bridge/dw_hdmi.h.
A few files relied on the file included in drmP.h - add explicit
include statements or forward declarations to these files.
Build tested with arm and x86.
v2:
- prefer forward declarations when possible (Laurent Pinchart)
- sort include files (Laurent Pinchart)
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190108192939.15255-7-sam@ravnborg.org
Kuo-Hsin Yang [Tue, 8 Jan 2019 07:45:17 +0000 (15:45 +0800)]
drm/gem: Mark pinned pages as unevictable
The gem drivers use shmemfs to allocate backing storage for gem objects.
On Samsung Chromebook Plus, the drm/rockchip driver may call
rockchip_gem_get_pages -> drm_gem_get_pages -> shmem_read_mapping_page
to pin a lot of pages, breaking the page reclaim mechanism and causing
oom-killer invocation.
E.g. when the size of a zone is 3.9 GiB, the inactive_ratio is 5. If
active_anon / inactive_anon < 5 and all pages in the inactive_anon lru
are pinned, page reclaim would keep scanning inactive_anon lru without
reclaiming memory. It breaks page reclaim when the rockchip driver only
pins about 1/6 of the anon lru pages.
Mark these pinned pages as unevictable to avoid the premature oom-killer
invocation. See also similar patch on i915 driver [1].
[1]: https://patchwork.freedesktop.org/patch/msgid/
20181106132324.17390-1-chris@chris-wilson.co.uk
Signed-off-by: Kuo-Hsin Yang <vovoy@chromium.org>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190108074517.209860-1-vovoy@chromium.org
Sam Ravnborg [Tue, 8 Jan 2019 19:29:30 +0000 (20:29 +0100)]
drm: make drm_framebuffer.h self contained
Add forward declaration and pull in include
file to make drm_framebuffer.h self contained.
While add it order include files alphabetically.
The use of TASK_COMM_LEN is the reason for including sched.h.
I could not see any good way to avoid this dependency,
and users of drm_framebuffer.comm already use
TASK_COMM_LEN to check for length etc.
v2:
- Added forward declaration of drm_gem_object (Noralf)
- Added ack from Noralf
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190108192939.15255-4-sam@ravnborg.org
Sam Ravnborg [Tue, 8 Jan 2019 19:29:29 +0000 (20:29 +0100)]
drm: move DRM_SWITCH_POWER defines to drm_device.h
Move DRM_SWITCH_POWER out of drmP.h to allow users
to get rid of the drmP include.
Moved to drm_device.h because drm_device.switch_power_state
is the only user.
Converted to enum and added sparse kerneldoc comments.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190108192939.15255-3-sam@ravnborg.org
Sam Ravnborg [Tue, 8 Jan 2019 19:29:28 +0000 (20:29 +0100)]
drm: drm_device.h: update comments to kernel-doc style
Updated comment style to kernel-doc format in drm_device.h
In struct drm_device there are 12 struct members without doc:
- registered
- filelist_mutex
- filelist
- irq
- vbl_lock
- event_lock
- hose
- sigdata
- sigdata.context
- sigdata.lock
- agp_buffer_map
- agp_buffer_token
They all need proper documentation, a task left for someone
that knows their usage.
drm_device is not plugged into Documentation/gpu/drm-internals.rst
as this would create a new load of warnings.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190108192939.15255-2-sam@ravnborg.org
Shayenne Moura [Thu, 20 Dec 2018 12:27:57 +0000 (10:27 -0200)]
drm: i915: Cleanup drm_display_mode print str
This patch adjust the print string of drm_display_mode object
to remove drm_mode_object dependency in i915 files.
It modifies the print style to standardize the use of DRM_MODE_FMT.
Signed-off-by: Shayenne Moura <shayenneluzmoura@gmail.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/087e07a388c7c65b6d0ec50db069640e4eb32fdf.1545308167.git.shayenneluzmoura@gmail.com
Shayenne Moura [Thu, 20 Dec 2018 12:27:30 +0000 (10:27 -0200)]
drm: sti: Cleanup drm_display_mode print str
This patch adjust the print string of drm_display_mode object
to remove drm_mode_object dependency in sti files.
Signed-off-by: Shayenne Moura <shayenneluzmoura@gmail.com>
Acked-by: Benjamin Gaignard <benjamin;gaignard@linaro.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/c079f461575aece9d598784da25aaadc711a2729.1545308167.git.shayenneluzmoura@gmail.com
Shayenne Moura [Thu, 20 Dec 2018 12:26:55 +0000 (10:26 -0200)]
drm: meson: Cleanup on drm_display_mode print str
This patch adjust the print string of drm_display_mode object
to remove drm_mode_object dependency in meson files.
Signed-off-by: Shayenne Moura <shayenneluzmoura@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/7017942bbbb3e0e6c1e2bd854ea5a5f461784ac4.1545308167.git.shayenneluzmoura@gmail.com
Shayenne Moura [Thu, 20 Dec 2018 12:26:10 +0000 (10:26 -0200)]
drm: omapdrm: Cleanup drm_display_mode print str
This patch adjust the print string of drm_display_mode object
to remove drm_mode_object dependency in omapdrm files.
Signed-off-by: Shayenne Moura <shayenneluzmoura@gmail.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/cb6079fa6de6fda8d865a1d2a61d7cf10019ae88.1545308167.git.shayenneluzmoura@gmail.com
Gustavo A. R. Silva [Tue, 8 Jan 2019 16:21:52 +0000 (10:21 -0600)]
qxl: Use struct_size() in kzalloc()
One of the more common cases of allocation size calculations is finding the
size of a structure that has a zero-sized array at the end, along with memory
for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = kzalloc(sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can now
use the new struct_size() helper:
instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20190108162152.GA25361@embeddedor
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Ezequiel Garcia [Tue, 8 Jan 2019 14:59:30 +0000 (11:59 -0300)]
drm/virtio: Drop deprecated load/unload initialization
Move the code around so the driver is probed the bus
.probe and removed from the bus .remove callbacks.
This commit is just a cleanup and shouldn't affect
functionality.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20190108145930.15080-1-ezequiel@collabora.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Peter Wu [Sun, 23 Dec 2018 00:55:07 +0000 (01:55 +0100)]
drm/fb-helper: fix leaks in error path of drm_fb_helper_fbdev_setup
After drm_fb_helper_fbdev_setup calls drm_fb_helper_init,
"dev->fb_helper" will be initialized (and thus drm_fb_helper_fini will
have some effect). After that, drm_fb_helper_initial_config is called
which may call the "fb_probe" driver callback.
This driver callback may call drm_fb_helper_defio_init (as is done by
drm_fb_helper_generic_probe) or set a framebuffer (as is done by bochs)
as documented. These are normally cleaned up on exit by
drm_fb_helper_fbdev_teardown which also calls drm_fb_helper_fini.
If an error occurs after "fb_probe", but before setup is complete, then
calling just drm_fb_helper_fini will leak resources. This was triggered
by
df2052cc922 ("bochs: convert to drm_fb_helper_fbdev_setup/teardown"):
[ 50.008030] bochsdrmfb: enable CONFIG_FB_LITTLE_ENDIAN to support this framebuffer
[ 50.009436] bochs-drm 0000:00:02.0: [drm:drm_fb_helper_fbdev_setup] *ERROR* fbdev: Failed to set configuration (ret=-38)
[ 50.011456] [drm] Initialized bochs-drm 1.0.0
20130925 for 0000:00:02.0 on minor 2
[ 50.013604] WARNING: CPU: 1 PID: 1 at drivers/gpu/drm/drm_mode_config.c:477 drm_mode_config_cleanup+0x280/0x2a0
[ 50.016175] CPU: 1 PID: 1 Comm: swapper/0 Tainted: G T 4.20.0-rc7 #1
[ 50.017732] EIP: drm_mode_config_cleanup+0x280/0x2a0
...
[ 50.023155] Call Trace:
[ 50.023155] ? bochs_kms_fini+0x1e/0x30
[ 50.023155] ? bochs_unload+0x18/0x40
This can be reproduced with QEMU and CONFIG_FB_LITTLE_ENDIAN=n.
Link: https://lkml.kernel.org/r/20181221083226.GI23332@shao2-debian
Link: https://lkml.kernel.org/r/20181223004315.GA11455@al
Fixes: 8741216396b2 ("drm/fb-helper: Add drm_fb_helper_fbdev_setup/teardown()")
Reported-by: kernel test robot <rong.a.chen@intel.com>
Cc: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Peter Wu <peter@lekensteyn.nl>
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20181223005507.28328-1-peter@lekensteyn.nl
Noralf Trønnes [Sat, 5 Jan 2019 18:18:46 +0000 (19:18 +0100)]
drm/fb-helper: generic: Fix setup error path
If register_framebuffer() fails during fbdev setup we will leak the
framebuffer, the GEM buffer and the shadow buffer for defio. This is
because drm_fb_helper_fbdev_setup() just calls drm_fb_helper_fini() on
error not taking into account that register_framebuffer() can fail.
Since the generic emulation uses DRM client for its framebuffer and
backing buffer in addition to a shadow buffer, it's necessary to open code
drm_fb_helper_fbdev_setup() to properly handle the error path.
Error cleanup is removed from .fb_probe and is handled by one function for
all paths.
Fixes: 9060d7f49376 ("drm/fb-helper: Finish the generic fbdev emulation")
Reported-by: Peter Wu <peter@lekensteyn.nl>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190105181846.26495-1-noralf@tronnes.org
Gerd Hoffmann [Wed, 19 Dec 2018 12:27:01 +0000 (13:27 +0100)]
drm/virtio: drop virtio_gpu_fence_cleanup()
Just call drm_fence_put directly instead.
Also set vgfb->fence to NULL after dropping the reference.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20181219122708.4586-4-kraxel@redhat.com
Gerd Hoffmann [Wed, 19 Dec 2018 12:27:00 +0000 (13:27 +0100)]
drm/virtio: fix pageflip flush
Sending the flush command only makes sense if we actually have
a framebuffer attached to the scanout (handle != 0).
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20181219122708.4586-3-kraxel@redhat.com
Gerd Hoffmann [Wed, 19 Dec 2018 12:26:59 +0000 (13:26 +0100)]
drm/virtio: log error responses
If we got an error response code from the host, print it to the log.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20181219122708.4586-2-kraxel@redhat.com
Ezequiel Garcia [Wed, 2 Jan 2019 17:55:07 +0000 (14:55 -0300)]
drm/virtio: Add missing virtqueue reset
As per the VirtIO spec, the virtqueues must be reset during cleanup
(see "3.3.1 Driver Requirements: Device Cleanup").
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20190102175507.4653-2-ezequiel@collabora.com
Ezequiel Garcia [Wed, 2 Jan 2019 17:55:06 +0000 (14:55 -0300)]
drm/virtio: Remove incorrect kfree()
The virtio_gpu_output is a member of struct virtio_gpu_device
and is not a dynamically-allocated chunk, so it's wrong to kfree() it.
Removing it fixes a memory corruption BUG() that can be triggered
when the virtio-gpu driver is removed.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20190102175507.4653-1-ezequiel@collabora.com
Daniel Vetter [Mon, 7 Jan 2019 10:22:38 +0000 (11:22 +0100)]
drm/todo: Better defio support in the generic fbdev emulation
The current one essentially means you need CMA or a vmalloc backed
object, which makes fbdev emulation a special case.
Since implementing this will be quite a bit of work, capture the idea
in a TODO.
Cc: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190107102238.7789-1-daniel.vetter@ffwll.ch
Maxime Ripard [Mon, 7 Jan 2019 15:43:24 +0000 (16:43 +0100)]
Merge tag 'topic/drmp-cleanup-2019-01-02' of git://anongit.freedesktop.org/drm/drm-intel into drm-misc-next
Make some drm headers self-contained with includes and forward declarations
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
# gpg: Signature made Wed 02 Jan 2019 10:47:51 AM CET
# gpg: using RSA key
1565A65B77B0632E1124E59CD398079D26ABEE6F
# gpg: Can't check signature: No public key
From: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/87pntfl6pa.fsf@intel.com
YueHaibing [Sat, 29 Dec 2018 02:49:07 +0000 (10:49 +0800)]
drm: Fix error handling in drm_legacy_addctx
'ctx->handle' is unsigned, it never less than zero.
This patch use int 'tmp_handle' to handle the err condition.
Fixes: 62968144e673 ("drm: convert drm context code to use Linux idr")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20181229024907.12852-1-yuehaibing@huawei.com
Chris Wilson [Sun, 30 Dec 2018 12:28:42 +0000 (12:28 +0000)]
drm: Reorder set_property_atomic to avoid returning with an active ww_ctx
Delay the drm_modeset_acquire_init() until after we check for an
allocation failure so that we can return immediately upon error without
having to unwind.
WARNING: lock held when returning to user space!
4.20.0+ #174 Not tainted
------------------------------------------------
syz-executor556/8153 is leaving the kernel with locks still held!
1 lock held by syz-executor556/8153:
#0:
000000005100c85c (crtc_ww_class_acquire){+.+.}, at:
set_property_atomic+0xb3/0x330 drivers/gpu/drm/drm_mode_object.c:462
Reported-by: syzbot+6ea337c427f5083ebdf2@syzkaller.appspotmail.com
Fixes: 144a7999d633 ("drm: Handle properties in the core for atomic drivers")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Cc: <stable@vger.kernel.org> # v4.14+
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181230122842.21917-1-chris@chris-wilson.co.uk
Jani Nikula [Fri, 28 Dec 2018 08:28:15 +0000 (10:28 +0200)]
drm: forward declare struct drm_file in drm_syncobj.h
drm_syncobj.h uses struct drm_file pointers, forward declare struct
drm_file to make the header self-contained. This prepares for dropping
drmP.h from files including drm_syncobj.h.
Switch from "" to <> includes while at it.
v2: forward declare instead of including drm_file.h (Daniel)
[Updated commit message per Laurent's review while applying.]
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181228082815.10797-1-jani.nikula@intel.com
Jani Nikula [Thu, 27 Dec 2018 12:56:39 +0000 (14:56 +0200)]
drm: include types.h from drm_hdcp.h
drm_hdcp.h uses kernel integer types, make it self-contained by
including linux/kernel.h. This prepares for dropping drmP.h from files
including drm_hdcp.h.
[Updated commit message per Laurent's review while applying.]
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/adfc79941e827b49eb6186f317cbeff0fb365f33.1545915059.git.jani.nikula@intel.com
Jani Nikula [Thu, 27 Dec 2018 12:56:38 +0000 (14:56 +0200)]
drm: include idr.h from drm_file.h
drm_file.h embeds idr structures in DRM-specific structures. Include the
corresponding header to make drm_file.h self-contained. Make it easier
to drop drmP.h includes.
[Updated commit message per Laurent's review while applying.]
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/2818b15332ab562722dfc324cf977b7eb4a04401.1545915059.git.jani.nikula@intel.com
Jani Nikula [Thu, 27 Dec 2018 12:56:37 +0000 (14:56 +0200)]
drm: include kernel.h and agp_backend.h from intel-gtt.h
intel-gtt.h uses kernel and agp pointers, make it self-contained by
including the relevant headers. This prepares for dropping drmP.h from
files including intel-gtt.h.
[Updated commit message per Laurent's review while applying.]
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/9414800f89d6f326c6e9173233bf6c4dee254d9a.1545915059.git.jani.nikula@intel.com
Jani Nikula [Fri, 28 Dec 2018 13:04:46 +0000 (15:04 +0200)]
drm: un-inline drm_legacy_findmap()
Un-inline drm_legacy_findmap() to not depend on struct drm_device
definition within drm_legacy.h, so that a forward declaration suffices.
Also include drm_hashtab.h in drm_legacy.h to make it more
self-contained. Make it easier to drop drmP.h includes.
v2: avoid including drm_device.h by un-inlining (Daniel)
[Updated commit message per Laurent's review while applying.]
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181228130446.22141-1-jani.nikula@intel.com
Sam Ravnborg [Wed, 26 Dec 2018 21:03:47 +0000 (22:03 +0100)]
drm: move DRM_IF_VERSION to drm_internal.h
Move DRM_IF_VERSION out of drmP.h to allow users
to get rid of the drmP include.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20181226210353.13993-1-sam@ravnborg.org
Brajeswar Ghosh [Mon, 24 Dec 2018 14:36:36 +0000 (20:06 +0530)]
drm/drm_drv.c: Remove duplicate header
Remove drm_crtc_internal.h which is included more than once
Signed-off-by: Brajeswar Ghosh <brajeswar.linux@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20181224143636.GA3237@hp-pavilion-15-notebook-pc-brajeswar
Yangtao Li [Fri, 30 Nov 2018 16:11:01 +0000 (11:11 -0500)]
dma-buf: Change to use DEFINE_SHOW_ATTRIBUTE macro
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20181130161101.3413-1-tiny.windzz@gmail.com
Gerd Hoffmann [Thu, 20 Dec 2018 10:11:21 +0000 (11:11 +0100)]
drm/bochs: add edid present check
Check header before trying to read the complete edid blob, to avoid the
log being spammed in case qemu has no edid support (old qemu or edid
support turned off).
Fixes: 01f23459cf drm/bochs: add edid support.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20181220101122.16153-1-kraxel@redhat.com
Boris Brezillon [Thu, 6 Dec 2018 14:24:39 +0000 (15:24 +0100)]
drm/vc4: Attach margin props to the HDMI connector
Now that the plane code takes the margins setup into account, we can
safely attach margin props to the HDMI connector.
We also take care of filling AVI infoframes correctly to expose the
top/botton/left/right bar.
Note that those margin props match pretty well the
overscan_{left,right,top,bottom} properties defined in config.txt and
parsed by the VC4 firmware.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20181206142439.10441-6-boris.brezillon@bootlin.com
Boris Brezillon [Thu, 6 Dec 2018 14:24:38 +0000 (15:24 +0100)]
drm/vc4: Take margin setup into account when updating planes
Applyin margins is just a matter of scaling all planes appropriately
and adjusting the CRTC X/Y offset to account for the
left/right/top/bottom borders.
Create a vc4_plane_margins_adj() function doing that and call it from
vc4_plane_setup_clipping_and_scaling() so that we are ready to attach
margins properties to the HDMI connector.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20181206142439.10441-5-boris.brezillon@bootlin.com
Boris Brezillon [Thu, 6 Dec 2018 14:24:37 +0000 (15:24 +0100)]
drm/connector: Allow creation of margin props alone
TV margins properties can only be added as part of the SDTV TV
connector properties creation, but we might need those props for HDMI
TVs too, so let's move the margins props creation in a separate
function and expose it to drivers.
We also add an helper to attach margins props to a connector.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20181206142439.10441-4-boris.brezillon@bootlin.com
Boris Brezillon [Thu, 6 Dec 2018 14:24:36 +0000 (15:24 +0100)]
drm/connector: Clarify the unit of TV margins
All margins are expressed in pixels. Clarify that in the doc.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20181206142439.10441-3-boris.brezillon@bootlin.com
Boris Brezillon [Thu, 6 Dec 2018 14:24:35 +0000 (15:24 +0100)]
drm/connector: Fix drm_mode_create_tv_properties() doc
The in the kernel-doc header did not match the function name.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20181206142439.10441-2-boris.brezillon@bootlin.com
Kuninori Morimoto [Tue, 18 Dec 2018 06:00:24 +0000 (15:00 +0900)]
drm: dw-hdmi-i2s: convert to SPDX identifiers
This patch updates license to use SPDX-License-Identifier
instead of verbose license text.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/87lg4n1izg.wl-kuninori.morimoto.gx@renesas.com
Archit Taneja [Thu, 13 Sep 2018 07:53:00 +0000 (13:23 +0530)]
MAINTAINERS: drm: Remove myself as drm-bridge maintainer
I have moved on to other stuff for now. Haven't been able to make time
to review bridge related work. Andrzej has been doing it by himself
for a while now.
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Sean Paul <sean@poorly.run>
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180913075300.22510-1-architt@codeaurora.org
emersion [Sun, 16 Dec 2018 18:49:08 +0000 (18:49 +0000)]
drm/vkms: set preferred depth to 24
Otherwise DRM_CAP_DUMB_PREFERRED_DEPTH is zero.
Signed-off-by: Simon Ser <contact@emersion.fr>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/o2SmEP0M6h287Fs5OeL3HtQzTr8uV0PyOhFict_qdxeS7vFvV1Zr8qzRUJh-YnCoJHo13nJgAqqQByzEzTZTqk9R2ExsOszYLj68hQLqBIc=@emersion.fr
Dan Carpenter [Mon, 17 Dec 2018 07:03:44 +0000 (10:03 +0300)]
drm/ati_pcigart: Fix error code in drm_ati_pcigart_init()
The drm_ati_pcigart_init() function was originally suppose to return one
on success and zero on failure, but these days it returns a mix of
zero, one and -ENOMEM on failure.
This patch cleans it up and modifies the caller so now the function
returns zero on success and negative error codes on failure.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20181217070344.GC12159@kadam
Dan Carpenter [Mon, 17 Dec 2018 07:00:38 +0000 (10:00 +0300)]
drm: Fix an error pointer dereference()
The drm_mode_create_tile_group() is only called from
drm_parse_tiled_block() and the caller expects it to return a NULL on
error. In other words, this function should match
drm_mode_get_tile_group().
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20181217065733.GA12159@kadam
Lyude Paul [Fri, 14 Dec 2018 01:25:31 +0000 (20:25 -0500)]
drm/dp_mst: Refactor drm_dp_update_payload_part1()
This:
- Adds local variables in the first loop, instead of using array indices
everywhere
- Adds an early continue to reduce the indent level in the second loop
There should be no functional changes here
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Juston Li <juston.li@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181214012604.13746-3-lyude@redhat.com
Lyude Paul [Fri, 14 Dec 2018 01:25:30 +0000 (20:25 -0500)]
drm/dp_mst: Remove bogus conditional in drm_dp_update_payload_part1()
There's no reason we need this, it's just confusing looking.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Juston Li <juston.li@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20181214012604.13746-2-lyude@redhat.com
Gerd Hoffmann [Thu, 13 Dec 2018 13:49:15 +0000 (14:49 +0100)]
drm/virtio: switch to generic fbdev emulation
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Dave Airlie <airlied@redhat.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20181213134915.24722-1-kraxel@redhat.com
Shayenne da Luz Moura [Thu, 13 Dec 2018 22:55:37 +0000 (20:55 -0200)]
drm: Remove complete task from TODO documentation
This patch remove the follow complete task from TODO documentation:
drm_mode_config.crtc_idr is misnamed, since it contains all KMS object.
Should be renamed to drm_mode_config.object_idr.
Signed-off-by: Shayenne da Luz Moura <shayenneluzmoura@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20181213225537.nq4dwidn6tma33iv@smtp.gmail.com
Lyude Paul [Tue, 11 Dec 2018 23:50:26 +0000 (18:50 -0500)]
drm/dp_mst: Fix memory leak in drm_dp_mst_topology_mgr_destroy()
We need to call drm_dp_mst_topology_mgr_set_mst(mgr, false) when
destroying the topology manager in order to ensure that the root mstb
and all of it's descendents are actually destroyed, and additionally to
try to make sure that we leave the hub in a clean state.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Daniel Vetter <daniel@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20181211235026.21758-1-lyude@redhat.com
Shayenne da Luz Moura [Thu, 13 Dec 2018 21:29:57 +0000 (19:29 -0200)]
drm: Rename crtc_idr as object_idr to KMS cleanups
This patch solves this TODO task:
drm_mode_config.crtc_idr is misnamed, since it contains all KMS object.
Should be renamed to drm_mode_config.object_idr.
Signed-off-by: Shayenne da Luz Moura <shayenneluzmoura@gmail.com>
[danvet: resolve conflict with addition of privobj_list.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20181213212957.vkitkyl5cj2qh7qr@smtp.gmail.com
Heiko Stuebner [Fri, 30 Nov 2018 10:24:49 +0000 (11:24 +0100)]
drm/rockchip: Add implicit fencing support for planes
Render like lima will attach a fence to the framebuffer dma_buf,
so the display driver should wait for it to finish before showing
the framebufferto prevent tearing.
Generally tested on rk3188, rk3288, rk3328 and rk3399 and
together with an actual lima-based kmscube on rk3188 and rk3328.
Suggested-by: Qiang Yu <yuq825@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181130102449.6430-1-heiko@sntech.de
Daniel Vetter [Mon, 10 Dec 2018 10:03:58 +0000 (11:03 +0100)]
drm/xen: Don't set the dpms hook
Doesn't do anything for atomic.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Cc: xen-devel@lists.xen.org
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181210100359.22507-7-daniel.vetter@ffwll.ch
Daniel Vetter [Mon, 10 Dec 2018 10:03:57 +0000 (11:03 +0100)]
drm/qxl: Don't set the dpms hook
Doesn't do anything with atomic.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: virtualization@lists.linux-foundation.org
Cc: spice-devel@lists.freedesktop.org
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181210100359.22507-6-daniel.vetter@ffwll.ch
Christian König [Tue, 11 Dec 2018 10:34:41 +0000 (18:34 +0800)]
drm/syncobj: remove drm_syncobj_cb and cleanup
This completes "drm/syncobj: Drop add/remove_callback from driver
interface" and cleans up the implementation a bit.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Link: https://patchwork.freedesktop.org/patch/266255/
Christian König [Fri, 7 Dec 2018 19:10:17 +0000 (20:10 +0100)]
drm/etnaviv: fix for 64bit seqno change
The fence seqno is now 64bit, fixes build warning.
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/267136/
Rob Clark [Mon, 22 Oct 2018 12:31:22 +0000 (14:31 +0200)]
drm/atomic: integrate modeset lock with private objects
Follow the same pattern of locking as with other state objects. This
avoids boilerplate in the driver.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20181022123122.30468-1-boris.brezillon@bootlin.com
Ville Syrjälä [Fri, 28 Sep 2018 18:04:00 +0000 (21:04 +0300)]
drm/dp/mst: Validate REMOTE_I2C_READ harder
Make sure i2c msgs we're asked to transfer conform to the
requirements of REMOTE_I2C_READ. We were only checking that the
last message is a read, but we must also check that the preceding
messages are all writes. Also check that the length of each
message isn't too long.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180928180403.22499-2-ville.syrjala@linux.intel.com
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Ville Syrjälä [Fri, 28 Sep 2018 18:03:59 +0000 (21:03 +0300)]
drm/dp/mst: Configure no_stop_bit correctly for remote i2c xfers
We aren't supposed to force a stop+start between every i2c msg
when performing multi message transfers. This should eg. cause
the DDC segment address to be reset back to 0 between writing
the segment address and reading the actual EDID extension block.
To quote the E-DDC spec:
"... this standard requires that the segment pointer be
reset to 00h when a NO ACK or a STOP condition is received."
Since we're going to touch this might as well consult the
I2C_M_STOP flag to determine whether we want to force the stop
or not.
Cc: Brian Vincent <brainn@gmail.com>
References: https://bugs.freedesktop.org/show_bug.cgi?id=108081
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180928180403.22499-1-ville.syrjala@linux.intel.com
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
YueHaibing [Sat, 8 Dec 2018 08:36:25 +0000 (08:36 +0000)]
drm/ast: Remove set but not used variable 'bo'
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpu/drm/ast/ast_fb.c: In function 'astfb_create':
drivers/gpu/drm/ast/ast_fb.c:194:17: warning:
variable 'bo' set but not used [-Wunused-but-set-variable]
It never used since introduction in commit
312fec1405dd ("drm: Initial KMS
driver for AST (ASpeed Technologies) 2000 series (v2)")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1544258185-50430-1-git-send-email-yuehaibing@huawei.com
Daniel Vetter [Wed, 28 Nov 2018 22:12:34 +0000 (23:12 +0100)]
drm/dp-mst-helper: Remove hotplug callback
When everyone implements it exactly the same way, among all 4
implementations, there's not really a need to overwrite this at all.
Aside: drm_kms_helper_hotplug_event is pretty much core functionality
at this point. Probably should move it there.
Reviewed-by: Lyude Paul <lyude@redhat.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181128221234.15054-1-daniel.vetter@ffwll.ch
Boris Brezillon [Fri, 7 Dec 2018 08:36:06 +0000 (09:36 +0100)]
drm/vc4: Add support for X/Y reflection
Add support for X/Y reflection when the plane is using linear or
T-tiled formats. X/Y reflection hasn't been tested on SAND formats, so
we reject them until proper testing/debugging has been done.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20181207083606.15449-2-boris.brezillon@bootlin.com
Boris Brezillon [Fri, 7 Dec 2018 08:36:05 +0000 (09:36 +0100)]
drm/vc4: Fix negative X/Y positioning on SAND planes
Commit
3e407417b192 ("drm/vc4: Fix X/Y positioning of planes using
T_TILES modifier") fixed the problem with T_TILES format, but left
things in a non-working state for SAND formats. Address that now.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20181207083606.15449-1-boris.brezillon@bootlin.com
Eric Anholt [Mon, 3 Dec 2018 22:24:38 +0000 (14:24 -0800)]
drm/v3d: Invalidate the caches from the outside in.
This would be a fairly obscure race, but let's make sure we don't ever
lose it.
Signed-off-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20181203222438.25417-6-eric@anholt.net
Reviewed-by: Dave Emett <david.emett@broadcom.com>
Eric Anholt [Mon, 3 Dec 2018 22:24:37 +0000 (14:24 -0800)]
drm/v3d: Stop trying to flush L2C on V3D 3.3+
This cache was replaced with the slice accessing the L2T in the newer
generations. Noted by Dave during review.
Signed-off-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20181203222438.25417-5-eric@anholt.net
Reviewed-by: Dave Emett <david.emett@broadcom.com>
Eric Anholt [Mon, 3 Dec 2018 22:24:36 +0000 (14:24 -0800)]
drm/v3d: Drop the wait for L2T flush to complete.
According to Dave, once you've started an L2T flush, all L2T accesses
will be blocked until the flush completes. This fixes a consistent
3-4ms stall between the ioctl and running the job, and 3DMMES Taiji
goes from 27fps to 110fps.
v2: Leave a note about why we don't need to wait for completion.
Signed-off-by: Eric Anholt <eric@anholt.net>
Fixes: 57692c94dcbe ("drm/v3d: Introduce a new DRM driver for Broadcom V3D V3.x+")
Reviewed-by: Dave Emett <david.emett@broadcom.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181203222438.25417-4-eric@anholt.net
Eric Anholt [Mon, 3 Dec 2018 22:24:35 +0000 (14:24 -0800)]
drm/v3d: Don't bother flushing L1TD at job start.
This is the write combiner for TMU writes. You're supposed to flush
that at job end if you had dirtied any cachelines. Flushing it at job
start then doesn't make any sense.
Signed-off-by: Eric Anholt <eric@anholt.net>
Fixes: 57692c94dcbe ("drm/v3d: Introduce a new DRM driver for Broadcom V3D V3.x+")
Reviewed-by: Dave Emett <david.emett@broadcom.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181203222438.25417-3-eric@anholt.net
Eric Anholt [Mon, 3 Dec 2018 22:24:34 +0000 (14:24 -0800)]
drm/v3d: Drop unused v3d_flush_caches().
Now that I've specified how the end-of-pipeline flushing should work,
we're never going to use this function.
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Dave Emett <david.emett@broadcom.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181203222438.25417-2-eric@anholt.net
Eric Anholt [Mon, 3 Dec 2018 22:24:33 +0000 (14:24 -0800)]
drm/v3d: Document cache flushing ABI.
Right now, userspace doesn't do any L2T writes, but we should lay out
our expectations for how it works.
v2: Explicitly mention the VCD cache flushing requirements and that
we'll flush the other caches before each of the CLs.
Signed-off-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20181203222438.25417-1-eric@anholt.net
Reviewed-by: Dave Emett <david.emett@broadcom.com>
Mika Kuoppala [Fri, 7 Dec 2018 12:34:28 +0000 (14:34 +0200)]
drm/i915: Compile fix for 64b dma-fence seqno
Many errs of the form:
drivers/gpu/drm/i915/selftests/intel_hangcheck.c: In function ‘__igt_reset_evict_vma’:
./include/linux/kern_levels.h:5:18: error: format ‘%x’ expects argument of type ‘unsigned int’, but argum
Fixes: b312d8ca3a7c ("dma-buf: make fence sequence numbers 64 bit v2")
Cc: Christian König <christian.koenig@amd.com>
Cc: Chunming Zhou <david1.zhou@amd.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20181207123428.16257-1-mika.kuoppala@linux.intel.com
Christian König [Wed, 14 Nov 2018 15:11:06 +0000 (16:11 +0100)]
dma-buf: make fence sequence numbers 64 bit v2
For a lot of use cases we need 64bit sequence numbers. Currently drivers
overload the dma_fence structure to store the additional bits.
Stop doing that and make the sequence number in the dma_fence always
64bit.
For compatibility with hardware which can do only 32bit sequences the
comparisons in __dma_fence_is_later only takes the lower 32bits as significant
when the upper 32bits are all zero.
v2: change the logic in __dma_fence_is_later
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Link: https://patchwork.freedesktop.org/patch/266927/
Gerd Hoffmann [Wed, 21 Nov 2018 09:01:29 +0000 (10:01 +0100)]
drm/qxl: add spice-devel list to MAINTAINERS
So qxl kernel patches are sent to the spice-devel list for review.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20181121090129.23506-1-kraxel@redhat.com
Christian König [Wed, 5 Dec 2018 19:43:02 +0000 (20:43 +0100)]
drm/v3d: fix broken build
I missed one case during the recent revert of the replace_fence
interface change.
Fixes: 0b258ed1a219 drm: revert "expand replace_fence to support timeline point v2"
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/266134/
Christian König [Wed, 14 Nov 2018 13:24:27 +0000 (14:24 +0100)]
drm: revert "expand replace_fence to support timeline point v2"
This reverts commit
9a09a42369a4a37a959c051d8e1a1f948c1529a4.
The whole interface isn't thought through. Since this function can't
fail we actually can't allocate an object to store the sync point.
Sorry, I should have taken the lead on this from the very beginning and
reviewed it more thoughtfully. Going to propose a new interface as a
follow up change.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Link: https://patchwork.freedesktop.org/patch/265580/
YueHaibing [Thu, 29 Nov 2018 06:00:33 +0000 (06:00 +0000)]
drm/tinydrm: Use kmemdup rather than duplicating its implementation in repaper_spi_transfer()
use kmemdup rather than duplicating its implementation
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1543471233-159568-1-git-send-email-yuehaibing@huawei.com
YueHaibing [Sat, 1 Dec 2018 03:20:44 +0000 (03:20 +0000)]
drm/vkms: Remove set but not used variable 'vkms_obj'
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpu/drm/vkms/vkms_plane.c: In function 'vkms_prepare_fb':
drivers/gpu/drm/vkms/vkms_plane.c:144:26: warning:
variable 'vkms_obj' set but not used [-Wunused-but-set-variable]
It never used since introduction in commit
8ce1bb0b5337 ("drm/vkms: map/unmap buffers in [prepare/cleanup]_fb hooks")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1543634444-186448-1-git-send-email-yuehaibing@huawei.com
Jernej Skrabec [Sun, 4 Nov 2018 18:26:45 +0000 (19:26 +0100)]
drm/sun4i: Add compatible for H6 display engine
H6 is first Allwinner SoC which supports 10 bit colors, HDR and AFBC.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-9-jernej.skrabec@siol.net
Eric Anholt [Sat, 1 Dec 2018 00:57:58 +0000 (16:57 -0800)]
drm/v3d: Add more tracepoints for V3D GPU rendering.
The core scheduler tells us when the job is pushed to the scheduler's
queue, and I had the job_run functions saying when they actually queue
the job to the hardware. By adding tracepoints for the very top of
the ioctls and the IRQs signaling job completion, "perf record -a -e
v3d:.\* -e gpu_scheduler:.\* <job>; perf script" gets you a pretty
decent timeline.
Signed-off-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20181201005759.28093-5-eric@anholt.net
Reviewed-by: Dave Emett <david.emett@broadcom.com>
Eric Anholt [Sat, 1 Dec 2018 00:57:59 +0000 (16:57 -0800)]
drm/v3d: Add missing fence timeline name for TFU.
We shouldn't be returning v3d-render for our new queue.
Signed-off-by: Eric Anholt <eric@anholt.net>
Fixes: 83d5139982db ("drm/v3d: Add support for submitting jobs to the TFU.")
Link: https://patchwork.freedesktop.org/patch/msgid/20181201005759.28093-6-eric@anholt.net
Reviewed-by: Dave Emett <david.emett@broadcom.com>
Christian König [Tue, 13 Nov 2018 13:14:00 +0000 (14:14 +0100)]
drm/syncobj: use dma_fence_get_stub
Extract of useful code from the timeline work. Let's use just a single
stub fence instance instead of allocating a new one all the time.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Link: https://patchwork.freedesktop.org/patch/265248/
Christian König [Mon, 3 Dec 2018 12:36:14 +0000 (13:36 +0100)]
dma-buf: add dma_fence_get_stub
Extract of useful code from the timeline work. This provides a function
to return a stub or dummy fence which is always signaled.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Link: https://patchwork.freedesktop.org/patch/265248/
Alex Gonzalez [Thu, 25 Oct 2018 15:09:30 +0000 (17:09 +0200)]
drm/panel: simple: Add AUO G101EVN010 panel support
The change adds support for the AU Optronics G101EVN010 10.1" TFT LCD
panel.
Signed-off-by: Alex Gonzalez <alex.gonzalez@digi.com>
Reviewed-by: Rob Herring <robh@kernel.org>
[treding@nvidia.com: sort new entry alphabetically]
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1540480173-12009-2-git-send-email-alex.gonzalez@digi.com
Neil Armstrong [Wed, 28 Nov 2018 10:07:34 +0000 (11:07 +0100)]
drm/meson: Fix an Alpha Primary Plane bug on Meson GXL/GXM SoCs
On the Amlogic GXL & GXM SoCs, a bug occurs on the primary plane when
alpha is used where the alpha is not aligned with the pixel content.
The workaround Amlogic implemented is to reset the OSD1 plane hardware
block each time the plane is (re)enabled, solving the issue.
In the reset, we still need to save the content of 2 registers which
depends on the status of the plane, in addition to reload the scaler
conversion matrix at the same time.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Maxime Jourdan <mjourdan@baylibre.com>
Reviewed-by: Maxime Jourdan <mjourdan@baylibre.com>
[narmstrong: fixed typo in commit log]
Link: https://patchwork.freedesktop.org/patch/msgid/20181128100734.6536-1-narmstrong@baylibre.com
Eric Anholt [Wed, 28 Nov 2018 23:09:27 +0000 (15:09 -0800)]
drm/v3d: Fix prime imports of buffers from other drivers.
v3d_bo_get_pages() checks this to decide to map the imported buffer
instead of the backing shmem file. The caller was about to set this
value anyway, and there's no error path in between. Ideally we
wouldn't even allocate the shmem file for our imports, but that's a
more invasive fix.
Signed-off-by: Eric Anholt <eric@anholt.net>
Fixes: 57692c94dcbe ("drm/v3d: Introduce a new DRM driver for Broadcom V3D V3.x+")
Link: https://patchwork.freedesktop.org/patch/msgid/20181128230927.10951-3-eric@anholt.net
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Dave Emett <david.emett@broadcom.com>
Eric Anholt [Wed, 28 Nov 2018 23:09:26 +0000 (15:09 -0800)]
drm/v3d: Drop the "dev" argument to lock/unlock of BO reservations.
They were unused, as Dave Emett noticed in TFU review.
Signed-off-by: Eric Anholt <eric@anholt.net>
Cc: Dave Emett <david.emett@broadcom.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181128230927.10951-2-eric@anholt.net
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Eric Anholt [Wed, 28 Nov 2018 23:09:25 +0000 (15:09 -0800)]
drm/v3d: Add support for submitting jobs to the TFU.
The TFU can copy from raster, UIF, and SAND input images to UIF output
images, with optional mipmap generation. This will certainly be
useful for media EGL image input, but is also useful immediately for
mipmap generation without bogging the V3D core down.
For now we only run the queue 1 job deep, and don't have any hang
recovery (though I don't think we should need it, with TFU). Queuing
multiple jobs in the HW will require synchronizing the YUV coefficient
regs updates since they don't get FIFOed with the job.
v2: Change the ioctl to IOW instead of IOWR, always set COEF0, explain
why TFU is AUTH, clarify the syncing docs, drop the unused TFU
interrupt regs (you're expected to use the hub's), don't take
&bo->base for NULL bos.
v3: Fix a little whitespace alignment (noticed by checkpatch), rebase
on drm_sched_job_cleanup() changes.
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Dave Emett <david.emett@broadcom.com> (v2)
Link: https://patchwork.freedesktop.org/patch/264607/
Daniel Vetter [Wed, 28 Nov 2018 10:07:28 +0000 (11:07 +0100)]
drm: Fix up drm_atomic_state_helper.[hc] extraction
I've misplaced two functions by accident:
- drm_atomic_helper_duplicate_state is really part of the
resume/suspend/shutdown device-wide helpers.
- drm_atomic_helper_legacy_gamma_set is part of the legacy ioctl
compat helpers.
Move them both back.
Fixes: 9ef8a9dc4b21 ("drm: Extract drm_atomic_state_helper.[hc]")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sean Paul <sean@poorly.run>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181128100728.4674-1-daniel.vetter@ffwll.ch
Sean Paul [Thu, 29 Nov 2018 20:36:48 +0000 (15:36 -0500)]
drm: Fix compiler warning in drm_atomic_helper.c
Kbuild was complaining about:
>> drivers/gpu/drm/drm_atomic_helper.c:3169:27: warning: 'state' may be used uninitialized in this function [-Wmaybe-uninitialized]
Now state can't actually be used uninitialized, but we'll assign a value
anyways so it stops bellyaching.
Kbuild config:
link: https://lists.01.org/pipermail/kbuild-all/2018-November/055374.html
tree: git://anongit.freedesktop.org/drm/drm-misc for-linux-next
head:
b7ea04d299c78b6cf96ab281a1683ff62a74f969
commit:
b7ea04d299c78b6cf96ab281a1683ff62a74f969 [4/4] drm: Add
DRM_MODESET_LOCK_BEGIN/END helpers
config: x86_64-randconfig-x017-201847 (attached as .config)
compiler: gcc-7 (Debian 7.3.0-1) 7.3.0
reproduce:
git checkout
b7ea04d299c78b6cf96ab281a1683ff62a74f969
# save the attached .config to linux build tree
make ARCH=x86_64
Fixes: b7ea04d299c7 ("drm: Add DRM_MODESET_LOCK_BEGIN/END helpers")
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
[seanpaul added extra details on airlied's suggestion]
Link: https://patchwork.freedesktop.org/patch/msgid/20181129203652.223634-1-sean@poorly.run
Sean Paul [Fri, 30 Nov 2018 13:47:01 +0000 (08:47 -0500)]
Merge drm/drm-next into drm-misc-next
Need to pick up the following patch to fix htmldocs build
167bfe534dc2 ("Documentation: drm: Remove dangling pointer from drm-mm.rst")
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Boris Brezillon [Fri, 30 Nov 2018 09:02:54 +0000 (10:02 +0100)]
drm/vc4: Allow YUV formats on cursor planes
Now that scaling is allowed on cursor planes, we can also allow YUV
formats.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20181130090254.594-6-boris.brezillon@bootlin.com
Boris Brezillon [Fri, 30 Nov 2018 09:02:53 +0000 (10:02 +0100)]
drm/vc4: Allow scaling on cursor plane
Now that async update has been reworked to allow scaled planes to be
updated asynchronously when the scaling params do not change, we can
remove the NO_SCALING constraint on cursor planes.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20181130090254.594-5-boris.brezillon@bootlin.com
Boris Brezillon [Fri, 30 Nov 2018 09:02:52 +0000 (10:02 +0100)]
drm/vc4: Rework the async update logic
vc4_plane_atomic_async_check() was only based on the
state->{crtc,src}_{w,h} which was fine since scaling was not allowed on
the cursor plane.
We are about to change that to properly support underscan, and, in order
to make the async check more reliable, we call vc4_plane_mode_set()
from there and check that only the pos0, pos2 and ptr0 entries in the
dlist have changed.
In vc4_plane_atomic_async_update(), we no longer call
vc4_plane_atomic_check() since vc4_plane_mode_set() has already been
called in vc4_plane_atomic_async_check(), and we don't need to allocate
a new LBM region (we reuse the one from the current state).
Note that we now have to manually update each field of the current
plane state since it's no longer updated in place (not sure we have
to sync all of them, but it's harmless if we do).
We also drop the vc4_plane_async_set_fb() call (ptr0 dlist entry has
been properly updated in vc4_plane_mode_set())
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20181130090254.594-4-boris.brezillon@bootlin.com
Boris Brezillon [Fri, 30 Nov 2018 09:02:51 +0000 (10:02 +0100)]
drm/vc4: Don't check plane state more than once
We are about to use vc4_plane_mode_set() in the async check path, but
async check can decide that async update is not possible and force the
driver to fallback to a sync update.
All the checks that have been done on the plane state during async check
stay valid, and checking it again is not necessary. Add a ->checked
field to vc4_plane_state, and use it to track the status of the state
(checked or not).
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20181130090254.594-3-boris.brezillon@bootlin.com
Boris Brezillon [Fri, 30 Nov 2018 09:02:50 +0000 (10:02 +0100)]
drm/vc4: Move LBM creation out of vc4_plane_mode_set()
We are about to use vc4_plane_mode_set() in the async check path, and
async updates require that LBM size stay the same since they reuse the
LBM from the previous state. So we definitely don't want to allocate a
new LBM region that we know for sure will be free right away.
Move the LBM allocation out of vc4_plane_mode_set() and call the new
function (vc4_plane_update_lbm()) from vc4_plane_atomic_check().
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20181130090254.594-2-boris.brezillon@bootlin.com
projects / openwrt / staging / blogic.git / log