gpio: rename pca953x symbols

This second part of an extension to support more pca953x chips renames the C
and Kconfig symbols.  All affected files were updated by sed, except for a
couple of obvious exceptions.  It also updates the Kconfig helptext.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

gpio: rename pca9539 driver

First part of an extension to let the pca9539 driver support more chips,
starting with pca9534, pca9535, pca9536, pca9537, and pca9538.

This renames the files and modifies the Makefile.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

w1-gpio: add GPIO w1 bus master driver

Add a GPIO 1-wire bus master driver.  The driver used the GPIO API to
control the wire and the GPIO pin can be specified using platform data
similar to i2c-gpio.  The driver was tested with AT91SAM9260 + DS2401.

Signed-off-by: Ville Syrjala <syrjala@sci.fi>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rtc: at91sam9 RTC support (RTT and/or RTC)

AT91sam9 RTC support, primarily in the form of an RTT-as-RTC driver that was
extracted from 2.6.23-at91 patch and updated:

 - Relies on now-merged platform updates, which associate the RTT
   hardware address with each RTT and use the "at91_rtt" name.

 - RTC framework related fixes and cleanups, notably:
    * removed now-needless suspend/resume clock offset logic
    * alarm read/write now respects the "enabled" flag
    * suspend always disables update irqs
    * shutdown (and startup) disables all irqs

 - Misc cleanup:
    * use dev_*() messaging
    * add comments
    * remove globals,
    * ... etc

 - Don't force use of RTT0 and GPBR0.  Either resource may need
   to be used for other purposes (like NO_HZ support).

 - Update "AT91RM9200 RTC" Kconfig to allow it on SAM9RL chips
   (it has both RTT and RTC).

Driver binding uses bus_find_device() to avoid needing any kind of "timer
library" code when there's more than one RTT module.  (This timer can be used
as an RTC, to support NO_HZ operation, or potentially for other stuff.  The
choice is a per-system policy.)

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Michel Benoit <murpme@gmail.com>
Cc: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rtc: remove more dev->power.power_state usage

Remove some more references to dev->power.power_state.  That field is overdue
for removal, but we can't do that while it's still referenced in the kernel.
The only reason to update it was to make the /sys/devices/.../power/state
files (now removed) work better.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rtc: cleanup example code

No functional changes here, just tighten up style/whitespace.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rtc: update documentation wrt irq_set_freq

Document the proper use of the irq_set_freq function.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rtc ds1307: ds_1340 change init

For DS140, clear the oscillator fault flag as needed.

Signed-off-by: Frederic RODO <f.rodo@til-technologies.fr>
[ And remove some "sparse" warnings. ]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rtc: add support for Epson RTC-9701JE V4

Add support for the Epson RTC-9701JE SPI RTC device.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rtc: add support for Epson RTC-9701JE V2

Add support for the Epson RTC-9701JE SPI RTC device.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ip27-rtc: convert ioctl to unlocked_ioctl

Convert ioctl call to unlocked_ioctl form.  It is possible (in that simple
way) due to a spinlock protection.

Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Acked-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rtc: add HPET RTC emulation to RTC_DRV_CMOS

That patch adds the RTC emulation of the HPET timer to the new RTC_DRV_CMOS.
The old drivers/char/rtc.ko driver had that functionality and it's important
on new systems.

[akpm@linux-foundation.org: unbreak alpha build]
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Andi Kleen <ak@suse.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Robert Picco <Robert.Picco@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Blackfin RTC driver: convert sync wait to use the irq write complete notice

 - thus clearing out the need for spin locks
 - add a small optimization for reading of the rtc field

Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Acked-by: Alessandro Zummo <alessandro.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Blackfin RTC driver: shave off another memcpy() by using assignment.

Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Acked-by: Alessandro Zummo <alessandro.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Blackfin RTC driver: read_alarm() checks the enabled field, not the pending field.

also, dont bother using memcpy since we can just do an assignment of the same structure.

Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Acked-by: Alessandro Zummo <alessandro.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Blackfin RTC driver: use dev_dbg() rather than pr_stamp()

Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Acked-by: Alessandro Zummo <alessandro.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Blackfin RTC driver: cleanup proc handler (we dont need RTC reg dump now that we have MMR filesystem in sysfs)

Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Acked-by: Alessandro Zummo <alessandro.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Blackfin RTC driver: we pass in a (struct device*) to the irq handler, not a (struct platform_device*), so fix the irq handler

Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Acked-by: Alessandro Zummo <alessandro.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Blackfin RTC driver: the frequency function is in units of Hz, not units of seconds, so lock our driver down to 1 Hz

Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Acked-by: Alessandro Zummo <alessandro.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Platform real time clock driver for Dallas 1511 chip

Add RTC support for DS1511 RTC/WDT chip.

Signed-off-by: Andy Sharp <andy.sharp@onstor.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rtc-cmos alarm acts as oneshot

Start making the rtc-cmos alarm act more like a oneshot alarm by disabling
that alarm after its IRQ fires.  (ACPI hooks are also needed.)

The Linux RTC framework has previously been a bit vague in this area, but
any other behavior is problematic and not very portable.  RTCs with full
YYYY-MM-DD HH:MM[:SS] alarms won't have a problem here.  Only ones with
partial match criteria, with the most visible example being the PC RTC, get
confused.  (Because the criteria will match repeatedly.)

Update comments relating to that oneshot behavior and timezone handling.
(Timezones are another issue that's mostly visible with rtc-cmos.  That's
because PCs often dual-boot MS-Windows, which likes its RTC to match local
wall-clock time instead of UTC.)

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rtc: ds1302 rtc support

This adds a basic ds1302 RTC driver, which is basically a cleanup and move
of the in-tree SH SecureEdge5410 code (which is currently located in
arch/sh/board/snapgear/rtc.c) to drivers/rtc.

This aims to be a building block that the M32R and CRIS code can be worked
on top of, so we can get rid of drivers/char/ds1302.c and
arch/cris/arch-v10/drivers/ds1302.c respectively, though more work is
needed for this.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rtc-cmos: export nvram in sysfs

This makes rtc-cmos export its NVRAM, like several other RTC drivers.

It still works within the limits of the current CMOS_READ/CMOS_WRITE calls,
which don't understand how to access multiple register banks.  The primary
impact of that limitation is that Linux can't access the uppermost 128
bytes of NVRAM on many systems.

Note that this isn't aiming to be a drop-in replacement for the legacy
/dev/nvram support.  (Presumably that has real users, and isn't just
getting carried forward automatically?) Userspace handles more work:

 - When userspace code updates NVRAM, that will need to include
   updating any platform-specific checksums that may apply.

 - No /proc/driver/nvram file will parse and display NVRAM data
   according to whichever boot firmware your board expects.

Also minor pnp-related updates: update a comment, remove dead code.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rtc-s3c: Use is_power_of_2() macro for simplicity.

Use is_power_of_2() macro for simplicity.

Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rtc-pcf8583: Don't abuse I2C_M_NOSTART

The rtc-pcf8583 driver is using the I2C_M_NOSTART flag but shouldn't.  This
flag is only meant for broken chips and the PCF8583 RTC chip is not one of
these.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Cosmetic fixes to RTC subsystem's Kconfig

Add adds a warning if a potentially conflicting RTC option has been
selected and makes some other cosmetic fixes to the Kconfig.

Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fuse: limit queued background requests

Libfuse basically creates a new thread for each new request.  This is fine for
synchronous requests, which are naturally limited.  However background
requests (especially writepage) can cause a thread creation storm.

To avoid this, limit the number of background requests available to userspace.

This is done by introducing another queue for background requests, and a
counter for the number of "active" requests, which are currently available for
userspace.

Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fuse: save space in struct fuse_req

Move the fields 'dentry' and 'vfsmount' into the request specific union, since
these are only used for the RELEASE request.

Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fuse: fix attribute caching after create

Invalidate attributes on create, since st_ctime is updated.  Reported by
Szabolcs Szakacsits.

Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ecryptfs: check for existing key_tfm at mount time

Jeff Moyer pointed out that a mount; umount loop of ecryptfs, with the same
cipher & other mount options, created a new ecryptfs_key_tfm_cache item
each time, and the cache could grow quite large this way.

Looking at this with mhalcrow, we saw that ecryptfs_parse_options()
unconditionally called ecryptfs_add_new_key_tfm(), which is what was adding
these items.

Refactor ecryptfs_get_tfm_and_mutex_for_cipher_name() to create a new
helper function, ecryptfs_tfm_exists(), which checks for the cipher on the
cached key_tfm_list, and sets a pointer to it if it exists.  This can then
be called from ecryptfs_parse_options(), and new key_tfm's can be added
only when a cached one is not found.

With list locking changes suggested by akpm.

Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Cc: Michael Halcrow <mhalcrow@us.ibm.com>
Cc: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

eCryptfs: change the type of cipher_code from u16 to u8

Only the lower byte of cipher_code is ever used, so it makes sense
for its type to be u8.

Signed-off-by: Trevor Highland <trevor.highland@gmail.com>
Cc: Michael Halcrow <mhalcrow@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

eCryptfs: Minor fixes to printk messages

The printk statements that result when the user does not have the
proper key available could use some refining.

Signed-off-by: Mike Halcrow <mhalcrow@us.ibm.com>
Cc: Mike Halcrow <mhalcrow@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ecryptfs: remove debug as mount option, and warn if set via modprobe

ecryptfs_debug really should not be a mount option; it is not per-mount,
but rather sets a global "ecryptfs_verbosity" variable which affects all
mounted filesysytems.  It's already settable as a module load option,
I think we can leave it at that.

Also, if set, since secret values come out in debug messages, kick
things off with a stern warning.

Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Acked-by: Mike Halcrow <mhalcrow@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ecryptfs: make show_options reflect actual mount options

Change ecryptfs_show_options to reflect the actual mount options in use.
Note that this does away with the "dir=" output, which is not a valid mount
option and appears to be unused.

Mount options such as "ecryptfs_verbose" and "ecryptfs_xattr_metadata" are
somewhat indeterminate for a given fs, but in any case the reported mount
options can be used in a new mount command to get the same behavior.

[akpm@linux-foundation.org: fix printk warning]
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Acked-by: Michael Halcrow <mhalcrow@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

eCryptfs: set inode key only once per crypto operation

There is no need to keep re-setting the same key for any given eCryptfs inode.
This patch optimizes the use of the crypto API and helps performance a bit.

Signed-off-by: Trevor Highland <trevor.highland@gmail.com>
Signed-off-by: Michael Halcrow <mhalcrow@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

eCryptfs: track header bytes rather than extents

Remove internal references to header extents; just keep track of header bytes
instead.  Headers can easily span multiple pages with the recent persistent
file changes.

Signed-off-by: Michael Halcrow <mhalcrow@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs/ecryptfs/: possible cleanups

- make the following needlessly global code static:
  - crypto.c:ecryptfs_lower_offset_for_extent()
  - crypto.c:key_tfm_list
  - crypto.c:key_tfm_list_mutex
  - inode.c:ecryptfs_getxattr()
  - main.c:ecryptfs_init_persistent_file()

- remove the no longer used mmap.c:ecryptfs_lower_page_cache

- #if 0 the unused read_write.c:ecryptfs_read()

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Michael Halcrow <mhalcrow@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/isdn/hardware/eicon/debug.c: fix uninitialized var warning

drivers/isdn/hardware/eicon/debug.c: In function 'SuperTraceASSIGN':
drivers/isdn/hardware/eicon/debug.c:1191: warning: 'rx_dma_magic' may be used uninitialized in this function

Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/isdn/hardware/eicon/message.c fix 'and' typo in eicons' AddInfo()

'!' has a higher priority than '&'.

Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ser_gigaset: convert mutex to completion

The ser_gigaset ISDN driver was using a mutex in its close() method for
waiting for other running ldisc methods to finish.  That's what completions
are for.  Incidentally, this also avoids a spurious "BUG: lock held at task
exit time" message when the driver's userspace daemon daemonizes itself.

Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Gigaset: permit module unload

Fix the initialization and reference counting of the Gigaset driver modules
so that they can be unloaded when they are not actually in use.

Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Cc: Hansjoerg Lipp <hjlipp@web.de>
Cc: Greg KH <gregkh@suse.de>
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

gigaset: atomic cleanup

Convert atomic_t variables that don't actually use atomic_t functionality
to int.

Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

usb_gigaset: suspend support

Add basic suspend/resume support to the usb_gigaset driver for the Siemens
Gigaset M105 USB DECT adapter.

Only the USB aspects are handled so far; the ISDN subsystem is not notified in
any way, for lack of information about how to do that.  The driver does not
check for active connections before suspending.  They will be dropped when the
device loses USB power.

Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Cc: Greg KH <gregkh@suse.de>
Cc: Hansjoerg Lipp <hjlipp@web.de>
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

bas_gigaset: suspend support

Add basic suspend/resume support to the bas_gigaset ISDN driver for the
Siemens Gigaset SX255 series of ISDN DECT bases.

Only the USB aspects are handled so far; the ISDN subsystem is not notified in
any way, for lack of information about how to do that.  The driver will refuse
to suspend if a connection is active.

Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Cc: Greg KH <gregkh@suse.de>
Cc: Hansjoerg Lipp <hjlipp@web.de>
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

gigaset: code cleanups

Some cleanups to the bas-gigaset and usb-gigaset USB ISDN drivers:
- simplified error handling
- improved debug messages
- readability improvements
- removal of obsolete defines and comments

Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Cc: Greg KH <gregkh@suse.de>
Cc: Hansjoerg Lipp <hjlipp@web.de>
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

gigaset: clean up urb->status usage

Make there only be one reference to urb->status per URB callback, and none
outside, in preparation for removal of that field.

Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Cc: Greg KH <gregkh@suse.de>
Cc: Hansjoerg Lipp <hjlipp@web.de>
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kprobes: kretprobe user entry-handler

Provide support to add an optional user defined callback to be run at
function entry of a kretprobe'd function.  Also modify the kprobe smoke
tests to include an entry-handler during the kretprobe sanity test.

Signed-off-by: Abhishek Sagar <sagar.abhishek@gmail.com>
Cc: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Acked-by: Jim Keniston <jkenisto@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

spi: remove more dev->power.power_state usage

Remove some more references to dev->power.power_state.  That field is overdue
for removal, but we can't do that while it's still referenced in the kernel.
The only reason to update it was to make the /sys/devices/.../power/state
files (now removed) work better.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

spi_bfin: headers are not for changelogs

Use simpler comment headers, and strip out information that is maintained in
GIT history

Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

spi_bfin: wait for tx to complete on write paths

SPI writes should also not return until the last bit is sent.

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

spi_bfin: wait for tx to complete on full duplex paths

Full duplex SPI operation should not read a dummy byte at the first transfer.
Bug and fix by Jean-Christian de Rivaz <jc@eclis.ch>:

http://blackfin.uclinux.org/gf/project/uclinux-dist/tracker/?action=TrackerItemEdit&tracker_item_id=3678

Signed-off-by: Jean-Christian de Rivaz <jc@eclis.ch>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

spi_bfin: wait for tx to complete on some cs_chg paths

PBX 2 SPI devices need the nonstandard "cs change per word" mechanism.

This patch is one of three updating this driver to make the last data bits get
sent before advancing the transfer ...  in this case, before the chipselect
gets deactivated.

Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

spi_bfin: use more useful GPIO labels

Use the SPI driver's name when requesting gpio lines.  When there are gpio
conflicts, this helps to narrow down the problems; "bfin-spi" is not
informative.

Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

spi_bfin: remove useless fault path

Remove useless return status check in restore_state function.  Issue was
pointed out by Michael.

Cc: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

spi: omap2_mcspi handles omap3 too

This adds driver OMAP SPI specific changes to support OMAP 3430

Signed-off-by: Girish S G <girishsg@ti.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

spi: SuperH SPI using SCI

Add support for SPI over SCI pins.  SCI is a very simple serial controller
block that can be found on older SuperH processors.  In theory it is
possible to use the SCI hardware block in syncronous mode, but this version
of the driver simply hooks up the bit banging code on the SCI pins.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

spi: s3c drivers shouldn't care about spi_board_info

The two S3C SPI master drivers got merged without much review, so I just
noticed that they're doing something that the SPI core code is responsible
for, rather than any adapter driver: they try to register SPI devices.

This removes that support from those drivers so they act normally.
Interestingly, none of the current boards are affected.  So it's a net code
shrink with no loss of functionality.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

atmel_spi: fix dmachain oops with DEBUG enabled

In atmel_spi_next_xfer, xfer can be NULL because the next transfer may
already have been submitted to the PDC (using DMA chaining).  This can
cause an oops, since the debug message assumed it was never null.  The
fix changes how those debug messages are issued, ensuring that one is
issued each time a transfer is started instead of once per call.

Also, properly indent the "can this transfer be chained" test so it's
not hidden as if it were non-conditional code.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

atmel_spi: chain DMA transfers

Add support for chained transfers in the atmel_spi driver, letting the DMA
controller switch to the next buffer pair without CPU intervention.  This
reduced I/O latencies by about 2% in one bulk I/O test.  It should also help
work around several interrelated errata affecting chipselect 0 on at91rm9200
chips.

Almost all of the changes are in the reworked atmel_spi_next_xfer() function.
That's now called with the driver in one of three states:

 1. It isn't transferring anything (in which case the first transfer
    of the current message is going to be sent)
 2. It has finished transfering a non-chainable transfer (in which
    case it will go to the next transfer in the message)
 3. It has finished transfering a chained transfer (in which case the
    next transfer is already queued)

After that it will queue the next transfer if it can be chained.

Signed-off-by: Szilveszter Ordog <slipszi@gmail.com>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

atmel_spi throughput improvement

Don't insert (undesirable) delays between consecutive words (DLYBCT) or when
activating chipselects (DLYBS).

Removing the between-word delays improves the performance of bulk transfers
(such as mtd_dataflash, m25p80, mmc_spi) significantly.  In one test, the
improvement was a factor of more than eight!

(The large DLYBCT value came from the legacy at91 SPI driver, and it's not
clear why it used such a huge value.)

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

spi core: stop updating dev->power.power_state

Don't update dev->power.power_state any more in the SPI core.  The only
reason to update this scheduled-to-be-removed field was to make the
already-removed /sys/devices/.../power/state files work better.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Atari floppy: Rename disk_type to atari_disk_type

Commit edfaa7c36574f1bf09c65ad602412db9da5f96bf

    Driver core: convert block from raw kobjects to core devices

    This moves the block devices to /sys/class/block. It will create a
    flat list of all block devices, with the disks and partitions in one
    directory. For compatibility /sys/block is created and contains symlinks
    to the disks.

introduced a global disk_type variable in <linux/genhd.h>, causing the
following compile error on Atari:

    drivers/block/ataflop.c:93: error: conflicting types for 'disk_type'
    include/linux/genhd.h:21: error: previous declaration of 'disk_type' was here

Rename the local disk_type variable in drivers/block/ataflop.c to
atari_disk_type, to avoid the conflict.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

W1: w1_therm.c standardize units to millidegrees C

Standardize the temperature units to millidegrees C for the two sensor
conversion routines.  Previously the routines were,

w1_DS18B20_convert_temp degrees C
w1_DS18S20_convert_temp millidegrees C

Unfortunately this will break any program using the ds18b20 value as it
will now be 1000 times bigger.  Fortunately there can't be that many users
out there, or some of these bugs will have been fixed by now, such as the
negative C error (see previous patch) that makes me think the ds18b20 is
the better choice to change because of the current bugs.

Signed-off-by: David Fries <david@fries.net>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/cdrom/cdrom.c: simplify logic in cdrom_release()

Simplify logic in cdrom_release() without semantic change.

Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

w1: remove unused and confusing variable.

Remvoe variable which actually is not used (except assigning it a value)
and confusing break out of the family checking loop.  Found by Harry Mason.

Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: Harry J Mason <hjm03r@ecs.soton.ac.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

tpm: infineon section mismatch

Fix section mismatch by making the driver template variable name
match one of the whitelisted variable names in modpost.

WARNING: vmlinux.o(.data+0x7a9e8): Section mismatch: reference to .init.text:tpm_inf_pnp_probe (between 'tpm_inf_pnp' and 'cn_idx')

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Marcel Selhorst <tpm@selhorst.net>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

speed up jiffies conversion functions if HZ==USER_HZ

Avoid calling do_div(x, 1) in this case.

Cc: David Fries <david@fries.net>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

system timer: fix crash in <100Hz system timer

The kernel has a divide by zero crash when trying to run the system timer
less than 100Hz.  The problem is x/(HZ/USER_HZ) and related.  Now
x*(USER_HZ/HZ) will be used if HZ<USER_HZ.

I'm running the Linux kernel under qemu and went to run a slower system
timer to take less CPU (and battery) on the host.  I found that the kernel
paniced under emulation because of a divide by zero in three places.  Here
is the patch.  The base git was updated today 01-05-2008.  I went for a
20Hz system time by adding config HZ_20 etc to kernel/Kconfig.hz.  With
this patch I verified the system timer by looking at /proc/interrupts.

[akpm@linux-foundation.org: partially clean up the macro maze]
Signed-off-by: David Fries <david@fries.net>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

phantom: don't grab other devices

Specify also sub pci ids to not grab devices with properly set sub ids.
This devices has these set (unset) to the same as (plx 9050) ids.

Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Andreas Block <andreas.block@esd-electronics.com>
Cc: Oliver Thimm <oliver.thimm@esd-electronics.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Claim maintainership for block2mtd and update email addresses

I have been prime author and maintainer of block2mtd from day one, but
neither MAINTAINERS nor the module source makes this fact clear.  And while
I'm at it, update my email addresses tree-wide, as the old address
currently bounces and change my name to "joern" as unicode will likely
continue to cause trouble until the end of this century.

Signed-off-by: Joern Engel <joern@lazybastard.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Documentation: add hint about call traces & module symbols to BUG-HUNTING

Here's a couple of small additions to BUG-HUNTING.

1. point out that you can list code in gdb with only one command
(gdb) l *(<symbol> + offset)

2. give a very brief hint how to decode module symbols in call traces

Signed-off-by: Richard Kennedy <richard@rsk.demon.co.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

make sys_poll() wait at least timeout ms

schedule_timeout(jiffies) waits for at least jiffies - 1.  Add 1 jiffie to
the timeout_jiffies calculated in sys_poll() to wait at least
timeout_msecs, like poll() manpage says.

Signed-off-by: Karsten Wiese <fzu@wemgehoertderstaat.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix IXANY and restart after signal (e.g. ctrl-C) in n_tty line discipline

Fix two N_TTY line discipline issues related to resuming a stopped TTY
(typically done with ctrl-S):

1) Fix handling of character that resumes a stopped TTY (with IXANY)

With "stty ixany", the TTY line discipline would lose the first character
after the stop, so typing, for example, "hi^Sthere" resulted in "hihere"
(the 't' would cause the resume after ^S, but it would then be thrown away
rather than processed as an input character).  This was inconsistent with
the behavior of other Unix systems.

2) Fix interrupt signal (e.g. ctrl-C) behavior in stopped TTYs

With "stty -ixany" (often the default), interrupt signals were ignored
in a stopped TTY until the TTY was resumed with the start char (typically
ctrl-Q), which was inconsistent with the behavior of other Unix systems.

Signed-off-by: Joe Peterson <joe@skyrush.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

docs: convert kref semaphore to mutex

Just converting this documentation semaphore reference, since we don't
want to promote semaphore usage.

Signed-off-by: Daniel Walker <dwalker@mvista.com>
Acked-by: Corey Minyard <minyard@acm.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Use ilog2() in fs/namespace.c

We can use ilog2() in fs/namespace.c to compute hash_bits and hash_mask at
compile time, not runtime.

[akpm@linux-foundation.org: clean it all up]
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

debug_smp_processor_id() fixlets

- Account for debug_smp_processor_id()'s own preempt_disable() when
  displaying the preempt_count().

- 80 cols, not 800.

Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kernel/sys.c: get rid of expensive divides in groups_sort()

groups_sort() can be quite long if user loads a large gid table.

This is because GROUP_AT(group_info, some_integer) uses an integer divide.
So having to do XXX thousand divides during one syscall can lead to very
high latencies.  (NGROUPS_MAX=65536)

In the past (25 Mar 2006), an analog problem was found in groups_search()
(commit d74beb9f33a5f16d2965f11b275e401f225c949d ) and at that time I
changed some variables to unsigned int.

I believe that a more generic fix is to make sure NGROUPS_PER_BLOCK is
unsigned.

Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

idle_regs() must be __cpuinit

Fix the following section mismatch with CONFIG_HOTPLUG=n,
CONFIG_HOTPLUG_CPU=y:

WARNING: vmlinux.o(.text+0x399a6): Section mismatch: reference to .init.text.5:idle_regs (between 'fork_idle' and 'get_task_mm')

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

calibrate_delay() must be __cpuinit

calibrate_delay() must be __cpuinit, not __{dev,}init.

I've verified that this is correct for all users.

While doing the latter, I also did the following cleanups:
- remove pointless additional prototypes in C files
- ensure all users #include <linux/delay.h>

This fixes the following section mismatches with CONFIG_HOTPLUG=n,
CONFIG_HOTPLUG_CPU=y:

WARNING: vmlinux.o(.text+0x1128d): Section mismatch: reference to .init.text.1:calibrate_delay (between 'check_cx686_slop' and 'set_cx86_reorder')
WARNING: vmlinux.o(.text+0x25102): Section mismatch: reference to .init.text.1:calibrate_delay (between 'smp_callin' and 'cpu_coregroup_map')

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Christian Zankel <chris@zankel.net>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kernel/params.c: remove sparse-warning (different signedness)

Fixing:
  CHECK   kernel/params.c
kernel/params.c:329:41: warning: incorrect type in argument 8 (different signedness)
kernel/params.c:329:41:    expected int *num
kernel/params.c:329:41:    got unsigned int *

Signed-off-by: Richard Knutsson <ricknu-0@student.ltu.se>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

lib/extable.c: remove an expensive integer divide in search_extable()

Actual code let compiler generates idiv instruction on x86.

Using a right shift is OK here and readable as well.

Before patch
   10:   57                      push   %edi
   11:   56                      push   %esi
   12:   89 d6                   mov    %edx,%esi
   14:   53                      push   %ebx
   15:   89 c3                   mov    %eax,%ebx
   17:   eb 22                   jmp    3b <search_extable+0x2b>
   19:   89 f0                   mov    %esi,%eax
   1b:   ba 02 00 00 00          mov    $0x2,%edx
   20:   29 d8                   sub    %ebx,%eax
   22:   89 d7                   mov    %edx,%edi
   24:   c1 f8 03                sar    $0x3,%eax
   27:   99                      cltd
   28:   f7 ff                   idiv   %edi
   2a:   8d 04 c3                lea    (%ebx,%eax,8),%eax
   2d:   39 08                   cmp    %ecx,(%eax)
...

After patch

00000010 <search_extable>:
   10:   53                      push   %ebx
   11:   89 c3                   mov    %eax,%ebx
   13:   eb 18                   jmp    2d <search_extable+0x1d>
   15:   89 d0                   mov    %edx,%eax
   17:   29 d8                   sub    %ebx,%eax
   19:   c1 f8 04                sar    $0x4,%eax
   1c:   8d 04 c3                lea    (%ebx,%eax,8),%eax
   1f:   39 08                   cmp    %ecx,(%eax)
...

Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

parport_pc: detection for SuperIO IT87XX POST

Add detection for IT87XX SuperIO chip and disabling its POST feature, which
made noise on parallel port's pins.

Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ik8: add Dell UK 6400 Inspiron model (MM061)

Add the Dell UK 6400 Inspiron model (MM061) to allow the i8k module to load
correctly without using 'force=1'

Signed-off-by: "Nick Warne" <nick@ukfsn.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

partition: use DEFAULT_SGI_PARTITION for SGI_PARTION default

Use DEFAULT_SGI_PARTITION for SGI_PARTION default

Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

parport_serial: netmos 9855 fix

Fix wrong netmos 9855 serial port configuration.

On loading only one serial port was present and it wasn't working.  After
looking in the data sheet I realized that the base address was wrong.  For
further reference here is lspci and relevant dmesg output:

02:00.0 Communication controller: NetMos Technology PCI 9855 Multi-I/O
Controller (rev 01) (prog-if 02)
        Subsystem: LSI Logic / Symbios Logic Unknown device 0022
        Flags: medium devsel, IRQ 19
        I/O ports at df00 [size=8]
        I/O ports at de00 [size=8]
        I/O ports at dd00 [size=8]
        I/O ports at dc00 [size=8]
        I/O ports at db00 [size=8]
        I/O ports at da00 [size=16]

parport1: PC-style at 0xdd00 [PCSPP,TRISTATE]
parport2: PC-style at 0xdf00 [PCSPP,TRISTATE,EPP]
0000:02:00.0: ttyS0 at I/O 0xdb00 (irq = 19) is a 16550A
0000:02:00.0: ttyS1 at I/O 0xda00 (irq = 19) is a 16550A

Signed-off-by: Christian Pellegrin <chripell@fsfe.org>
Cc: Thomas Richter <thor@math.TU-Berlin.DE>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Martin Schitter <ms@gewi.kfunigraz.ac.at>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

parport: add support for the Quatech SPPXP-100 Parallel port PCI ExpressCard

Added pci device id for the Quatech SPPXP-100 ExpressCard - 0x278 - to
include/linux/pci_id.h

Modified drivers/parport/parport_pc.c to support the Quatech SPPXP-100 Parallel port PCI ExpressCard

[akpm@linux-foundation.org: build fix]
Signed-off-by: Luís P Mendes <luis.p.mendes@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ext2: xip check fix

ext2 should not worry about checking sb->s_blocksize for XIP before the
sb's blocksize actually gets set.

Signed-off-by: Nick Piggin <npiggin@suse.de>
Acked-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Amiga serial driver: port_write_mutex fixup

The port_write_mutex was converted from a semaphore to a mutex,
but there was still this ifdef'd init_MUTEX reference remaining.

Signed-off-by: Daniel Walker <dwalker@mvista.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

stopmachine: semaphore to mutex

[akpm@linux-foundation.org: cleanup]
Signed-off-by: Daniel Walker <dwalker@mvista.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs/reiserfs/xattr.c: use LIST_HEAD instead of LIST_HEAD_INIT

Signed-off-by: Denis Cheng <crquan@gmail.com>
Cc: Chris Mason <chris.mason@oracle.com>
Cc: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/char/ipmi/ipmi_msghandler.c: use LIST_HEAD instead of LIST_HEAD_INIT

Signed-off-by: Denis Cheng <crquan@gmail.com>
Cc: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

docs: kernel-locking: Convert semaphore references

I converted some of the document to reflect mutex usage instead of
semaphore usage.  Since we shouldin't be promoting semaphore usage when
it's on it's way out..

Signed-off-by: Daniel Walker <dwalker@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

tty: enable the echoing of ^C in the N_TTY discipline

Turn on INTR/QUIT/SUSP echoing in the N_TTY line discipline (e.g.  ctrl-C
will appear as "^C" if stty echoctl is set and ctrl-C is set as INTR).

Linux seems to be the only unix-like OS (recently I've verified this on
Solaris, BSD, and Mac OS X) that does *not* behave this way, and I really
miss this as a good visual confirmation of the interrupt of a program in
the console or xterm.  I remember this fondly from many Unixs I've used
over the years as well.  Bringing this to Linux also seems like a good way
to make it yet more compliant with standard unix-like behavior.

[akpm@linux-foundation.org: coding-style fixes]
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Add arch_ptrace_stop

This adds support to allow asm/ptrace.h to define two new macros,
arch_ptrace_stop_needed and arch_ptrace_stop.  These control special
machine-specific actions to be done before a ptrace stop.  The new code
compiles away to nothing when the new macros are not defined.  This is the
case on all machines to begin with.

On ia64, these macros will be defined to solve the long-standing issue of
ptrace vs register backing store.

Signed-off-by: Roland McGrath <roland@redhat.com>
Cc: Petr Tesarik <ptesarik@suse.cz>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Matthew Wilcox <willy@debian.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

quota: improve inode list scanning in add_dquot_ref()

We restarted scan of sb->s_inodes list whenever we had to drop inode_lock
in add_dquot_ref().  This leads to overall quadratic running time and thus
add_dquot_ref() can take several minutes when called on a life filesystem.
We fix the problem by using the fact that inode cannot be removed from
s_inodes list while we hold a reference to it and thus we can safely
restart the scan if we don't drop the reference.  Here we use the fact that
inodes freshly added to s_inodes list are already guaranteed to have quotas
properly initialized and the ordering of inodes on s_inodes list does not
change so we cannot skip any inode.

Thanks goes to Nick <gentuu@gmail.com> for analyzing the problem and
testing the fix.

[akpm@linux-foundation.org: iput(NULL) is legal]
Signed-off-by: Jan Kara <jack@suse.cz>
Cc: Nick <gentuu@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/char: use LIST_HEAD instead of LIST_HEAD_INIT

single list_head variable initialized with LIST_HEAD_INIT could almost
always can be replaced with LIST_HEAD declaration, this shrinks the code
and looks better.

Signed-off-by: Denis Cheng <crquan@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

uio: nopage

Convert uio from nopage to fault.

Signed-off-by: Nick Piggin <npiggin@suse.de>
Acked-by: Hans J Koch <hjk@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

relay: nopage

Convert relay from nopage to fault.
Remove redundant vma range checks.
Switch from OOM to SIGBUS if the resource is not available.

Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Tom Zanussi <zanussi@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kallsyms should prefer non weak symbols

When resolving symbol names from addresses with aliased symbol names,
kallsyms_lookup always returns the first symbol, even if it is a weak
symbol.

This patch changes this by sorting the symbols with the weak symbols last
before feeding them to the kernel.  This way the kernel runtime isn't
changed at all, only the kallsyms build system is changed.

Another side effect is that the symbols get sorted by address, too.  So,
even if future binutils version have some bug in "nm" that makes it fail to
correctly sort symbols by address, the kernel won't be affected by this.

Mathieu says:

  I created a module in LTTng that uses kallsyms to get the symbol
  corresponding to a specific system call address.  Unfortunately, all the
  unimplemented syscalls were all referring to the (same) weak symbol
  identifying an unrelated system call rather that sys_ni (or whatever
  non-weak symbol would be expected).  Kallsyms was dumbly returning the first
  symbol that matched.

  This patch makes sure kallsyms returns the non-weak symbol when there is
  one, which seems to be the expected result.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Looks-great-to: Rusty Russell <rusty@rustcorp.com.au>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

unix98 allocated_ptys_lock semaphore to mutex

Convert the unix98 allocated_ptys_lock to a mutex.

Signed-off-by: Daniel Walker <dwalker@mvista.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>