Michal Wajdeczko [Wed, 22 May 2019 19:32:00 +0000 (19:32 +0000)]
drm/i915/uc: Use GuC firmware status helper
We already have helper function for checking GuC firmware
load status. Replace existing open-coded checks.
v2: drop redundant USES_GUC check
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190522193203.23932-7-michal.wajdeczko@intel.com
Michal Wajdeczko [Wed, 22 May 2019 19:31:59 +0000 (19:31 +0000)]
drm/i915/uc: Explicitly sanitize GuC/HuC on failure and finish
Explicitly sanitize GuC/HuC on load failure and when we finish
using them to make sure our fw state tracking is always correct.
While around, use new helper in uc_reset_prepare.
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190522193203.23932-6-michal.wajdeczko@intel.com
Michal Wajdeczko [Wed, 22 May 2019 19:31:58 +0000 (19:31 +0000)]
drm/i915/guc: Rename intel_guc_is_alive to intel_guc_is_loaded
This function just check our software flag, while 'is_alive'
may suggest that we are checking runtime firmware status.
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190522193203.23932-5-michal.wajdeczko@intel.com
Michal Wajdeczko [Wed, 22 May 2019 19:31:57 +0000 (19:31 +0000)]
drm/i915/selftests: Use prepare/finish during atomic reset test
We were testing full GPU reset in atomic context without correctly
wrapping it by prepare/finish steps. This could confuse our GuC
reset handling code.
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190522193203.23932-4-michal.wajdeczko@intel.com
Michal Wajdeczko [Wed, 22 May 2019 19:31:56 +0000 (19:31 +0000)]
drm/i915/selftests: Split igt_atomic_reset testcase
Split igt_atomic_reset selftests into separate full & engines parts,
so we can move former to the dedicated reset selftests file.
While here change engines test to loop first over atomic phases and
then loop over available engines.
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190522193203.23932-3-michal.wajdeczko@intel.com
Michal Wajdeczko [Wed, 22 May 2019 19:31:55 +0000 (19:31 +0000)]
drm/i915/selftests: Move some reset testcases to separate file
igt_global_reset and igt_wedged_reset testcases are first candidates.
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190522193203.23932-2-michal.wajdeczko@intel.com
Chris Wilson [Thu, 23 May 2019 06:49:33 +0000 (07:49 +0100)]
drm/i915/gtt: Always acquire struct_mutex for gen6_ppgtt_cleanup
We rearranged the vm_destroy_ioctl to avoid taking struct_mutex, little
realising that buried underneath the gen6 ppgtt release path was a
struct_mutex requirement (to remove its GGTT vma). Until that
struct_mutex is vanquished, take a detour in gen6_ppgtt_cleanup to do
the i915_vma_destroy from inside a worker under the struct_mutex.
<4> [257.740160] WARN_ON(debug_locks && !lock_is_held(&(&vma->vm->i915->drm.struct_mutex)->dep_map))
<4> [257.740213] WARNING: CPU: 3 PID: 1507 at drivers/gpu/drm/i915/i915_vma.c:841 i915_vma_destroy+0x1ae/0x3a0 [i915]
<4> [257.740214] Modules linked in: snd_hda_codec_hdmi i915 x86_pkg_temp_thermal mei_hdcp coretemp crct10dif_pclmul crc32_pclmul ghash_clmulni_intel snd_hda_codec_realtek snd_hda_codec_generic snd_hda_intel snd_hda_codec snd_hwdep snd_hda_core r8169 realtek snd_pcm mei_me mei prime_numbers lpc_ich
<4> [257.740224] CPU: 3 PID: 1507 Comm: gem_vm_create Tainted: G U 5.2.0-rc1-CI-CI_DRM_6118+ #1
<4> [257.740225] Hardware name: MSI MS-7924/Z97M-G43(MS-7924), BIOS V1.12 02/15/2016
<4> [257.740249] RIP: 0010:i915_vma_destroy+0x1ae/0x3a0 [i915]
<4> [257.740250] Code: 00 00 00 48 81 c7 c8 00 00 00 e8 ed 08 f0 e0 85 c0 0f 85 78 fe ff ff 48 c7 c6 e8 ec 30 a0 48 c7 c7 da 55 33 a0 e8 42 8c e9 e0 <0f> 0b 8b 83 40 01 00 00 85 c0 0f 84 63 fe ff ff 48 c7 c1 c1 58 33
<4> [257.740251] RSP: 0018:
ffffc90000aafc68 EFLAGS:
00010282
<4> [257.740252] RAX:
0000000000000000 RBX:
ffff8883f7957840 RCX:
0000000000000003
<4> [257.740253] RDX:
0000000000000046 RSI:
0000000000000006 RDI:
ffffffff8212d1b9
<4> [257.740254] RBP:
ffffc90000aafcc8 R08:
0000000000000000 R09:
0000000000000000
<4> [257.740255] R10:
0000000000000000 R11:
0000000000000000 R12:
ffff8883f4d5c2a8
<4> [257.740256] R13:
ffff8883f4d5d680 R14:
ffff8883f4d5c668 R15:
ffff8883f4d5c2f0
<4> [257.740257] FS:
00007f777fa8fe40(0000) GS:
ffff88840f780000(0000) knlGS:
0000000000000000
<4> [257.740258] CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
<4> [257.740259] CR2:
00007f777f6522b0 CR3:
00000003c612a006 CR4:
00000000001606e0
<4> [257.740260] Call Trace:
<4> [257.740283] gen6_ppgtt_cleanup+0x25/0x60 [i915]
<4> [257.740306] i915_ppgtt_release+0x102/0x290 [i915]
<4> [257.740330] i915_gem_vm_destroy_ioctl+0x7c/0xa0 [i915]
<4> [257.740376] ? i915_gem_vm_create_ioctl+0x160/0x160 [i915]
<4> [257.740379] drm_ioctl_kernel+0x83/0xf0
<4> [257.740382] drm_ioctl+0x2f3/0x3b0
<4> [257.740422] ? i915_gem_vm_create_ioctl+0x160/0x160 [i915]
<4> [257.740426] ? _raw_spin_unlock_irqrestore+0x39/0x60
<4> [257.740430] do_vfs_ioctl+0xa0/0x6e0
<4> [257.740433] ? lock_acquire+0xa6/0x1c0
<4> [257.740436] ? __task_pid_nr_ns+0xb9/0x1f0
<4> [257.740439] ksys_ioctl+0x35/0x60
<4> [257.740441] __x64_sys_ioctl+0x11/0x20
<4> [257.740443] do_syscall_64+0x55/0x1c0
<4> [257.740445] entry_SYSCALL_64_after_hwframe+0x49/0xbe
References:
e0695db7298e ("drm/i915: Create/destroy VM (ppGTT) for use with contexts")
Fixes: 7f3f317a66ca ("drm/i915: Restore control over ppgtt for context creation ABI")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190523064933.23604-1-chris@chris-wilson.co.uk
Jani Nikula [Wed, 22 May 2019 10:35:05 +0000 (13:35 +0300)]
drm/i915: remove duplicate typedef for intel_wakeref_t
Fix the duplicate typedef for intel_wakeref_t leading to Clang build
issues. While at it, actually make the intel_runtime_pm.h header
self-contained, which was claimed in the commit being fixed.
Reported-by: Nathan Chancellor <natechancellor@gmail.com>
Cc: Nathan Chancellor <natechancellor@gmail.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
References: http://mid.mail-archive.com/
20190521183850.GA9157@archlinux-epyc
References: https://travis-ci.com/ClangBuiltLinux/continuous-integration/jobs/
201754420#L2435
Fixes: 0d5adc5f2f01 ("drm/i915: extract intel_runtime_pm.h from intel_drv.h")
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Tested-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190522103505.2082-1-jani.nikula@intel.com
Jani Nikula [Thu, 23 May 2019 08:57:24 +0000 (11:57 +0300)]
drm/i915: Update DRIVER_DATE to
20190523
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Gwan-gyeong Mun [Tue, 21 May 2019 12:17:21 +0000 (15:17 +0300)]
drm/i915/dp: Support DP ports YUV 4:2:0 output to GEN11
Bspec describes that GEN10 only supports capability of YUV 4:2:0 output to
HDMI port and GEN11 supports capability of YUV 4:2:0 output to both DP and
HDMI ports.
v2: Minor style fix.
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190521121721.32010-7-gwan-gyeong.mun@intel.com
Gwan-gyeong Mun [Tue, 21 May 2019 12:17:20 +0000 (15:17 +0300)]
drm/i915/dp: Change a link bandwidth computation for DP
Data M/N calculations were assumed a bpp as RGB format. But when we are
using YCbCr 4:2:0 output format on DP, we should change bpp calculations
as YCbCr 4:2:0 format. The pipe_bpp value was assumed RGB format,
therefore, it was multiplied with 3. But YCbCr 4:2:0 requires a multiplier
value to 1.5.
Therefore we need to divide pipe_bpp to 2 while DP output uses YCbCr4:2:0
format.
- RGB format bpp = bpc x 3
- YCbCr 4:2:0 format bpp = bpc x 1.5
But Link M/N values are calculated and applied based on the Full Clock for
YCbCr 4:2:0. And DP YCbCr 4:2:0 does not need to pixel clock double for
a dotclock caluation. Only for HDMI YCbCr 4:2:0 needs to pixel clock double
for a dot clock calculation.
It only affects dp and edp port which use YCbCr 4:2:0 output format.
And for now, it does not consider a use case of DSC + YCbCr 4:2:0.
v2:
Addressed review comments from Ville.
Remove a changing of pipe_bpp on intel_ddi_set_pipe_settings().
Because the pipe is running at the full bpp, keep pipe_bpp as RGB
even though YCbCr 4:2:0 output format is used.
Add a link bandwidth computation for YCbCr4:2:0 output format.
v3:
Addressed reivew comments from Ville.
In order to make codes simple, it adds and uses intel_dp_output_bpp()
function.
v6:
Link M/N values are calculated and applied based on the Full Clock for
YCbCr420. The Bit per Pixel needs to be adjusted for YUV420 mode as it
requires only half of the RGB case.
- Link M/N values are calculated and applied based on the Full Clock
- Data M/N values needs to be calculated considering the data is half
due to subsampling
Remove a doubling of pixel clock on a dot clock calculator for
DP YCbCr 4:2:0.
Rebase and remove a duplicate setting of vsc_sdp.DB17.
Add a setting of dynamic range bit to vsc_sdp.DB17.
Change Content Type bit to "Graphics" from "Not defined".
Change a dividing of pipe_bpp to muliplying to constant values on a
switch-case statement.
v7:
Addressed review comments from Ville.
Move a setting of dynamic range bit and a setting of bpc which is based
on pipe_bpp to a "drm/i915/dp: Program VSC Header and DB for Pixel
Encoding/Colorimetry Format" commit.
Change Content Type bit to "Not defined" from "Graphics".
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190521121721.32010-6-gwan-gyeong.mun@intel.com
Gwan-gyeong Mun [Tue, 21 May 2019 12:17:19 +0000 (15:17 +0300)]
drm/i915/dp: Add a support of YCBCR 4:2:0 to DP MSA
When YCBCR 4:2:0 outputs is used for DP, we should program YCBCR 4:2:0 to
MSA and VSC SDP.
As per DP 1.4a spec section 2.2.4.3 [MSA Field for Indication of Color
Encoding Format and Content Color Gamut] while sending YCBCR 420 signals
we should program MSA MISC1 fields which indicate VSC SDP for the Pixel
Encoding/Colorimetry Format.
v2: Block comment style fix.
v6:
Fix an wrong setting of MSA MISC1 fields for Pixel Encoding/Colorimetry
Format indication. As per DP 1.4a spec Table 2-96 [MSA MISC1 and MISC0
Fields for Pixel Encoding/Colorimetry Format Indication]
When MISC1, bit 6, is Set to 1, a Source device uses a VSC SDP to
indicate the Pixel Encoding/Colorimetry Format. On the wrong version
it set a bit 5 of MISC1, now it set a bit 6 of MISC1.
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190521121721.32010-5-gwan-gyeong.mun@intel.com
Gwan-gyeong Mun [Tue, 21 May 2019 12:17:18 +0000 (15:17 +0300)]
drm/i915/dp: Program VSC Header and DB for Pixel Encoding/Colorimetry Format
Function intel_pixel_encoding_setup_vsc handles vsc header and data block
setup for pixel encoding / colorimetry format.
Setup VSC header and data block in function intel_pixel_encoding_setup_vsc
for pixel encoding / colorimetry format as per dp 1.4a spec,
section 2.2.5.7.1, table 2-119: VSC SDP Header Bytes, section 2.2.5.7.5,
table 2-120:VSC SDP Payload for DB16 through DB18.
v2:
Minor style fix. [Maarten]
Refer to commit ids instead of patchwork. [Maarten]
v6: Rebase
v7:
Rebase and addressed review comments from Ville.
Use a structure initializer instead of memset().
Fix non-standard comment format.
Remove a referring to specific commit.
Add a setting of dynamic range bit to vsc_sdp.DB17.
Add a setting of bpc which is based on pipe_bpp.
Remove duplicated checking of connector's ycbcr_420_allowed from
intel_pixel_encoding_setup_vsc(). It is already checked from
intel_dp_ycbcr420_config().
Remove comments for VSC_SDP_EXTENSION_FOR_COLORIMETRY_SUPPORTED. It is
already implemented on intel_dp_get_colorimetry_status().
v8:
A missing of setting bpc to VSC setup is the pretty fatal case, it
replaces DRM_DEBUG_KMS() to MISSING_CASE(). [Maarten]
v9: Use a changed member name of struct dp_sdp. it renamed to db from DB.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190521121721.32010-4-gwan-gyeong.mun@intel.com
Gwan-gyeong Mun [Tue, 21 May 2019 12:17:17 +0000 (15:17 +0300)]
drm: Rename struct edp_vsc_psr to struct dp_sdp
VSC SDP Payload for PSR is one of data block type of SDP (Secondaray Data
Packet). In order to generalize SDP packet structure name, it renames
struct edp_vsc_psr to struct dp_sdp. And each SDP data blocks have
different usages, each SDP type has different reserved data blocks and
Video_Stream_Configuration Extension VESA SDP might use all of Data Blocks
as Extended INFORFRAME Data Byte. so it makes Data Block variables as
array type. And it adds comments of details of DB of VSC SDP Payload
for Pixel Encoding/Colorimetry Format. This comments follows DP 1.4a spec,
section 2.2.5.7.5, chapter "VSC SDP Payload for Pixel Encoding/Colorimetry
Format".
v7: Addressed review comments from Ville.
v9: Rename a member value name DB to db on struct dp_sdp [Laurent]
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190521121721.32010-3-gwan-gyeong.mun@intel.com
Gwan-gyeong Mun [Tue, 21 May 2019 12:17:16 +0000 (15:17 +0300)]
drm/i915/dp: Add a config function for YCBCR420 outputs
This patch checks a support of YCBCR420 outputs on an encoder level.
If the input mode is YCBCR420-only mode then it prepares DP as an YCBCR420
output, else it continues with RGB output mode.
It set output_format to INTEL_OUTPUT_FORMAT_YCBCR420 in order to using
a pipe scaler as RGB to YCbCr 4:4:4.
v2:
Addressed review comments from Ville.
Style fixed with few naming.
%s/config/crtc_state/
%s/intel_crtc/crtc/
If lscon is active, it makes not to call intel_dp_ycbcr420_config()
to avoid to clobber of lspcon_ycbcr420_config() routine.
And it move the 420_only check into the intel_dp_ycbcr420_config().
v3: Fix uninitialized return value and it is reported by Dan Carpenter.
v4:
Addressed review comments from Ville.
In order to avoid the extra indentation, it inverts if-clause on
intel_dp_ycbcr420_config().
Remove the error print where no errors print are allowed.
v6: Rebase
v7:
Move intel_dp_get_colorimetry_status() to intel_dp from intel_psr.
intel_dp_get_colorimetry_status() checks
VSC_SDP_EXTENSION_FOR_COLORIMETRY_SUPPORTED bit in the
DPRX_FEATURE_ENUMERATION_LIST register.
And intel_dp_ycbcr420_config() uses intel_dp_get_colorimetry_status().
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190521121721.32010-2-gwan-gyeong.mun@intel.com
Tvrtko Ursulin [Wed, 22 May 2019 09:00:54 +0000 (10:00 +0100)]
drm/i915: Engine discovery query
Engine discovery query allows userspace to enumerate engines, probe their
configuration features, all without needing to maintain the internal PCI
ID based database.
A new query for the generic i915 query ioctl is added named
DRM_I915_QUERY_ENGINE_INFO, together with accompanying structure
drm_i915_query_engine_info. The address of latter should be passed to the
kernel in the query.data_ptr field, and should be large enough for the
kernel to fill out all known engines as struct drm_i915_engine_info
elements trailing the query.
As with other queries, setting the item query length to zero allows
userspace to query minimum required buffer size.
Enumerated engines have common type mask which can be used to query all
hardware engines, versus engines userspace can submit to using the execbuf
uAPI.
Engines also have capabilities which are per engine class namespace of
bits describing features not present on all engine instances.
v2:
* Fixed HEVC assignment.
* Reorder some fields, rename type to flags, increase width. (Lionel)
* No need to allocate temporary storage if we do it engine by engine.
(Lionel)
v3:
* Describe engine flags and mark mbz fields. (Lionel)
* HEVC only applies to VCS.
v4:
* Squash SFC flag into main patch.
* Tidy some comments.
v5:
* Add uabi_ prefix to engine capabilities. (Chris Wilson)
* Report exact size of engine info array. (Chris Wilson)
* Drop the engine flags. (Joonas Lahtinen)
* Added some more reserved fields.
* Move flags after class/instance.
v6:
* Do not check engine info array was zeroed by userspace but zero the
unused fields for them instead.
v7:
* Simplify length calculation loop. (Lionel Landwerlin)
v8:
* Remove MBZ comments where not applicable.
* Rename ABI flags to match engine class define naming.
* Rename SFC ABI flag to reflect it applies to VCS and VECS.
* SFC is wired to even _logical_ engine instances.
* SFC applies to VCS and VECS.
* HEVC is present on all instances on Gen11. (Tony)
* Simplify length calculation even more. (Chris Wilson)
* Move info_ptr assigment closer to loop for clarity. (Chris Wilson)
* Use vdbox_sfc_access from runtime info.
* Rebase for RUNTIME_INFO.
* Refactor for lower indentation.
* Rename uAPI class/instance to engine_class/instance to avoid C++
keyword.
v9:
* Rebase for s/num_rings/num_engines/ in RUNTIME_INFO.
v10:
* Use new copy_query_item.
v11:
* Consolidate with struct i915_engine_class_instnace.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jon Bloomfield <jon.bloomfield@intel.com>
Cc: Dmitry Rogozhkin <dmitry.v.rogozhkin@intel.com>
Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tony Ye <tony.ye@intel.com>
Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com> # v7
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190522090054.6007-1-tvrtko.ursulin@linux.intel.com
Tvrtko Ursulin [Mon, 20 May 2019 11:04:42 +0000 (12:04 +0100)]
drm/i915/icl: Add WaDisableBankHangMode
Disable GPU hang by default on unrecoverable ECC cache errors.
v2:
* Rebase.
v3:
* Use intel_uncore_read. (Chris)
Fixes: cc38cae7c4e9 ("drm/i915/icl: Introduce initial Icelake Workarounds")
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190520110442.403-2-tvrtko.ursulin@linux.intel.com
Tvrtko Ursulin [Mon, 20 May 2019 14:25:46 +0000 (15:25 +0100)]
drm/i915/selftests: Verify context workarounds
Test context workarounds have been correctly applied in newly created
contexts.
To accomplish this the existing engine_wa_list_verify helper is extended
to take in a context from which reading of the workaround list will be
done.
Context workaround verification is done from the existing subtests, which
have been renamed to reflect they are no longer only about GT and engine
workarounds.
v2:
* Test after resets and refactor to use intel_context more. (Chris)
v3:
* Use ce->engine->i915 instead of ce->gem_context->i915. (Chris)
* gem_engine_iter.idx is engine->id + 1. (Chris)
v4:
* Make local function static.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190520142546.12493-1-tvrtko.ursulin@linux.intel.com
Chris Wilson [Tue, 21 May 2019 21:11:34 +0000 (22:11 +0100)]
drm/i915: Allow specification of parallel execbuf
There is a desire to split a task onto two engines and have them run at
the same time, e.g. scanline interleaving to spread the workload evenly.
Through the use of the out-fence from the first execbuf, we can
coordinate secondary execbuf to only become ready simultaneously with
the first, so that with all things idle the second execbufs are executed
in parallel with the first. The key difference here between the new
EXEC_FENCE_SUBMIT and the existing EXEC_FENCE_IN is that the in-fence
waits for the completion of the first request (so that all of its
rendering results are visible to the second execbuf, the more common
userspace fence requirement).
Since we only have a single input fence slot, userspace cannot mix an
in-fence and a submit-fence. It has to use one or the other! This is not
such a harsh requirement, since by virtue of the submit-fence, the
secondary execbuf inherit all of the dependencies from the first
request, and for the application the dependencies should be common
between the primary and secondary execbuf.
Suggested-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Testcase: igt/gem_exec_fence/parallel
Link: https://github.com/intel/media-driver/pull/546
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190521211134.16117-10-chris@chris-wilson.co.uk
Chris Wilson [Tue, 21 May 2019 21:11:33 +0000 (22:11 +0100)]
drm/i915/execlists: Virtual engine bonding
Some users require that when a master batch is executed on one particular
engine, a companion batch is run simultaneously on a specific slave
engine. For this purpose, we introduce virtual engine bonding, allowing
maps of master:slaves to be constructed to constrain which physical
engines a virtual engine may select given a fence on a master engine.
For the moment, we continue to ignore the issue of preemption deferring
the master request for later. Ideally, we would like to then also remove
the slave and run something else rather than have it stall the pipeline.
With load balancing, we should be able to move workload around it, but
there is a similar stall on the master pipeline while it may wait for
the slave to be executed. At the cost of more latency for the bonded
request, it may be interesting to launch both on their engines in
lockstep. (Bubbles abound.)
Opens: Also what about bonding an engine as its own master? It doesn't
break anything internally, so allow the silliness.
v2: Emancipate the bonds
v3: Couple in delayed scheduling for the selftests
v4: Handle invalid mutually exclusive bonding
v5: Mention what the uapi does
v6: s/nbond/num_bonds/
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190521211134.16117-9-chris@chris-wilson.co.uk
Chris Wilson [Tue, 21 May 2019 21:11:32 +0000 (22:11 +0100)]
drm/i915: Extend execution fence to support a callback
In the next patch, we will want to configure the slave request
depending on which physical engine the master request is executed on.
For this, we introduce a callback from the execute fence to convey this
information.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190521211134.16117-8-chris@chris-wilson.co.uk
Chris Wilson [Tue, 21 May 2019 21:11:31 +0000 (22:11 +0100)]
drm/i915: Apply an execution_mask to the virtual_engine
Allow the user to direct which physical engines of the virtual engine
they wish to execute one, as sometimes it is necessary to override the
load balancing algorithm.
v2: Only kick the virtual engines on context-out if required
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190521211134.16117-7-chris@chris-wilson.co.uk
Chris Wilson [Tue, 21 May 2019 21:11:30 +0000 (22:11 +0100)]
drm/i915: Load balancing across a virtual engine
Having allowed the user to define a set of engines that they will want
to only use, we go one step further and allow them to bind those engines
into a single virtual instance. Submitting a batch to the virtual engine
will then forward it to any one of the set in a manner as best to
distribute load. The virtual engine has a single timeline across all
engines (it operates as a single queue), so it is not able to concurrently
run batches across multiple engines by itself; that is left up to the user
to submit multiple concurrent batches to multiple queues. Multiple users
will be load balanced across the system.
The mechanism used for load balancing in this patch is a late greedy
balancer. When a request is ready for execution, it is added to each
engine's queue, and when an engine is ready for its next request it
claims it from the virtual engine. The first engine to do so, wins, i.e.
the request is executed at the earliest opportunity (idle moment) in the
system.
As not all HW is created equal, the user is still able to skip the
virtual engine and execute the batch on a specific engine, all within the
same queue. It will then be executed in order on the correct engine,
with execution on other virtual engines being moved away due to the load
detection.
A couple of areas for potential improvement left!
- The virtual engine always take priority over equal-priority tasks.
Mostly broken up by applying FQ_CODEL rules for prioritising new clients,
and hopefully the virtual and real engines are not then congested (i.e.
all work is via virtual engines, or all work is to the real engine).
- We require the breadcrumb irq around every virtual engine request. For
normal engines, we eliminate the need for the slow round trip via
interrupt by using the submit fence and queueing in order. For virtual
engines, we have to allow any job to transfer to a new ring, and cannot
coalesce the submissions, so require the completion fence instead,
forcing the persistent use of interrupts.
- We only drip feed single requests through each virtual engine and onto
the physical engines, even if there was enough work to fill all ELSP,
leaving small stalls with an idle CS event at the end of every request.
Could we be greedy and fill both slots? Being lazy is virtuous for load
distribution on less-than-full workloads though.
Other areas of improvement are more general, such as reducing lock
contention, reducing dispatch overhead, looking at direct submission
rather than bouncing around tasklets etc.
sseu: Lift the restriction to allow sseu to be reconfigured on virtual
engines composed of RENDER_CLASS (rcs).
v2: macroize check_user_mbz()
v3: Cancel virtual engines on wedging
v4: Commence commenting
v5: Replace 64b sibling_mask with a list of class:instance
v6: Drop the one-element array in the uabi
v7: Assert it is an virtual engine in to_virtual_engine()
v8: Skip over holes in [class][inst] so we can selftest with (vcs0, vcs2)
Link: https://github.com/intel/media-driver/pull/283
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190521211134.16117-6-chris@chris-wilson.co.uk
Chris Wilson [Tue, 21 May 2019 21:11:29 +0000 (22:11 +0100)]
drm/i915: Allow userspace to clone contexts on creation
A usecase arose out of handling context recovery in mesa, whereby they
wish to recreate a context with fresh logical state but preserving all
other details of the original. Currently, they create a new context and
iterate over which bits they want to copy across, but it would much more
convenient if they were able to just pass in a target context to clone
during creation. This essentially extends the setparam during creation
to pull the details from a target context instead of the user supplied
parameters.
The ideal here is that we don't expose control over anything more than
can be obtained via CONTEXT_PARAM. That is userspace retains explicit
control over all features, and this api is just convenience.
For example, you could replace
struct context_param p = { .param = CONTEXT_PARAM_VM };
param.ctx_id = old_id;
gem_context_get_param(&p.param);
new_id = gem_context_create();
param.ctx_id = new_id;
gem_context_set_param(&p.param);
gem_vm_destroy(param.value); /* drop the ref to VM_ID handle */
with
struct create_ext_param p = {
{ .name = CONTEXT_CREATE_CLONE },
.clone_id = old_id,
.flags = CLONE_FLAGS_VM
}
new_id = gem_context_create_ext(&p);
and not have to worry about stray namespace pollution etc.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190521211134.16117-5-chris@chris-wilson.co.uk
Chris Wilson [Tue, 21 May 2019 21:11:28 +0000 (22:11 +0100)]
drm/i915: Re-expose SINGLE_TIMELINE flags for context creation
The SINGLE_TIMELINE flag can be used to create a context such that all
engine instances within that context share a common timeline. This can
be useful for mixing operations between real and virtual engines, or
when using a composite context for a single client API context.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190521211134.16117-4-chris@chris-wilson.co.uk
Chris Wilson [Tue, 21 May 2019 21:11:27 +0000 (22:11 +0100)]
drm/i915: Extend I915_CONTEXT_PARAM_SSEU to support local ctx->engine[]
Allow the user to specify a local engine index (as opposed to
class:index) that they can use to refer to a preset engine inside the
ctx->engine[] array defined by an earlier I915_CONTEXT_PARAM_ENGINES.
This will be useful for setting SSEU parameters on virtual engines that
are local to the context and do not have a valid global class:instance
lookup.
Note that due to the ambiguity in using class:instance with
ctx->engines[], if a user supplied engine map is active the user must
specify the engine to alter by its index into the ctx->engines[].
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190521211134.16117-3-chris@chris-wilson.co.uk
Chris Wilson [Tue, 21 May 2019 21:11:26 +0000 (22:11 +0100)]
drm/i915: Allow a context to define its set of engines
Over the last few years, we have debated how to extend the user API to
support an increase in the number of engines, that may be sparse and
even be heterogeneous within a class (not all video decoders created
equal). We settled on using (class, instance) tuples to identify a
specific engine, with an API for the user to construct a map of engines
to capabilities. Into this picture, we then add a challenge of virtual
engines; one user engine that maps behind the scenes to any number of
physical engines. To keep it general, we want the user to have full
control over that mapping. To that end, we allow the user to constrain a
context to define the set of engines that it can access, order fully
controlled by the user via (class, instance). With such precise control
in context setup, we can continue to use the existing execbuf uABI of
specifying a single index; only now it doesn't automagically map onto
the engines, it uses the user defined engine map from the context.
v2: Fixup freeing of local on success of get_engines()
v3: Allow empty engines[]
v4: s/nengine/num_engines/
v5: Replace 64 limit on num_engines with a note that execbuf is
currently limited to only using the first 64 engines.
v6: Actually use the engines_mutex to guard the ctx->engines.
Testcase: igt/gem_ctx_engines
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190521211134.16117-2-chris@chris-wilson.co.uk
Chris Wilson [Tue, 21 May 2019 21:11:25 +0000 (22:11 +0100)]
drm/i915: Restore control over ppgtt for context creation ABI
Having hid the partially exposed new ABI from the PR, put it back again
for completion of context recovery. A significant part of context
recovery is the ability to reuse as much of the old context as is
feasible (to avoid expensive reconstruction). The biggest chunk kept
hidden at the moment is fine-control over the ctx->ppgtt (the GPU page
tables and associated translation tables and kernel maps), so make
control over the ctx->ppgtt explicit.
This allows userspace to create and share virtual memory address spaces
(within the limits of a single fd) between contexts they own, along with
the ability to query the contexts for the vm state.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190521211134.16117-1-chris@chris-wilson.co.uk
Ville Syrjälä [Thu, 9 May 2019 12:21:59 +0000 (15:21 +0300)]
drm/i915: Bump gen7+ fb size limits to 16kx16k
With gtt remapping in place we can use arbitrarily large
framebuffers. Let's bump the limits to 16kx16k on gen7+.
The limit was chosen to match the maximum 2D surface size
of the 3D engine.
With the remapping we could easily go higher than that for the
display engine. However the modesetting ddx will blindly assume
it can handle whatever is reported via kms. The oversized
buffer dimensions are not caught by glamor nor Mesa until
finally an assert will trip when genxml attempts to pack the
SURFACE_STATE. So we pick a safe limit to avoid the X server
from crashing (or potentially misbehaving if the genxml asserts
are compiled out).
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=110187
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190509122159.24376-9-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Ville Syrjälä [Thu, 9 May 2019 12:21:58 +0000 (15:21 +0300)]
drm/i915: Bump fb stride limit to 128KiB for gen4+ and 256KiB for gen7+
With gtt remapping plugged in we can simply raise the stride
limit on gen4+. Let's just pick the limit to match the render
engine max stride (256KiB on gen7+, 128KiB on gen4+).
No remapping CCS because the virtual address of each page actually
matters due to the new hash mode
(WaCompressedResourceDisplayNewHashMode:skl,kbl etc.), and no
remapping on gen2/3 due extra complications from fence alignment
and gen2 2KiB GTT tile size. Also no real benefit since the
display engine limits already match the other limits.
v2: Rebase due to is_ccs_modifier()
v3: Tweak the comment and commit msg
v4: Fix gen4+ stride limit to be 128KiB
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> #v3
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190509122159.24376-8-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Ville Syrjälä [Thu, 9 May 2019 12:21:57 +0000 (15:21 +0300)]
drm/i915: Align dumb buffer stride to 4k to allow for gtt remapping
Align dumb buffer stride to 4k if the fb will be big enough to
require gtt remapping.
v2: Leave the stride alone for buffers that look to be for the cursor
v3: Make it not a hack (Daniel)
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190509122159.24376-7-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Ville Syrjälä [Thu, 9 May 2019 12:21:56 +0000 (15:21 +0300)]
drm/i915: Overcome display engine stride limits via GTT remapping
The display engine stride limits are getting in our way. On SKL+
we are limited to 8k pixels, which is easily exceeded with three
4k displays. To overcome this limitation we can remap the pages
in the GTT to provide the display engine with a view of memory
with a smaller stride.
The code is mostly already there as We already play tricks with
the plane surface address and x/y offsets.
A few caveats apply:
* linear buffers need the fb stride to be page aligned, as
otherwise the remapped lines wouldn't start at the same
spot
* compressed buffers can't be remapped due to the new
ccs hash mode causing the virtual address of the pages
to affect the interpretation of the compressed data. IIRC
the old hash was limited to the low 12 bits so if we were
using that mode we could remap. As it stands we just refuse
to remapp with compressed fbs.
* no remapping gen2/3 as we'd need a fence for the remapped
vma, which we currently don't have. Need to deal with the
fence POT requirements, and do something about the gen2
gtt page size vs tile size difference
v2: Rebase due to is_ccs_modifier()
Fix up the skl+ stride_mult mess
memset() the gtt_view because otherwise we could leave
junk in plane[1] when going from 2 plane to 1 plane format
v3: intel_check_plane_stride() was split out
v4: Drop the aligned viewport stuff, it was meant for ccs which
can't be remapped anyway
v5: Introduce intel_plane_can_remap()
Reorder the code so that plane_state->view gets filled
even for invisible planes, otherwise we'd keep using
stale values and could explode during remapping. The new
logic never remaps invisible planes since we don't have
a viewport, and instead pins the full fb instead
v6: Fix plane src coord checks after remapping by moving
plane_state->base.src to the final plane x/y offsets.
Allow intel_plane_check_stride() to fail even with
remapping (can happen at least with a linear 64bpp
fb with a 4k plane and a suitably inconvenient src
coordinates).
Improve aux plane FIXME (Daniel)
Move some code shuffling into a separate patch (Daniel)
Testcase: igt/kms_big_fb
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190509122159.24376-6-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Ville Syrjälä [Thu, 9 May 2019 12:21:55 +0000 (15:21 +0300)]
drm/i915: Shuffle stride checking code around
Reorganize some fb stride checking code a bit to prepare for
gtt remapping. And do a bit of s/pitch/stride/ renaming in the
process for a bit more uniformity (apart from the whole
fb->pitches[] thing).
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190509122159.24376-5-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Ville Syrjälä [Thu, 9 May 2019 12:21:54 +0000 (15:21 +0300)]
drm/i915/selftests: Add live vma selftest
Add a live selftest to excercise rotated/remapped vmas. We simply
write through the rotated/remapped vma, and confirm that the data
appears in the right page when read through the normal vma.
Not sure what the fallout of making all rotated/remapped vmas
mappable/fenceable would be, hence I just hacked it in the test.
v2: Grab rpm reference (Chris)
GEM_BUG_ON(view.type not as expected) (Chris)
Allow CAN_FENCE for rotated/remapped vmas (Chris)
Update intel_plane_uses_fence() to ask for a fence
only for normal vmas on gen4+
v3: Deal with intel_wakeref_t
v4: Rebase
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190509122159.24376-4-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Ville Syrjälä [Thu, 9 May 2019 12:21:53 +0000 (15:21 +0300)]
drm/i915/selftests: Add mock selftest for remapped vmas
Extend the rotated vma mock selftest to cover remapped vmas as
well.
TODO: reindent the loops I guess? Left like this for now to
ease review
v2: Include the vma type in the error message (Chris)
v3: Deal with trimmed sg
v4: Drop leftover debugs
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190509122159.24376-3-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Ville Syrjälä [Thu, 9 May 2019 12:21:52 +0000 (15:21 +0300)]
drm/i915: Add a new "remapped" gtt_view
To overcome display engine stride limits we'll want to remap the
pages in the GTT. To that end we need a new gtt_view type which
is just like the "rotated" type except not rotated.
v2: Use intel_remapped_plane_info base type
s/unused/unused_mbz/ (Chris)
Separate BUILD_BUG_ON()s (Chris)
Use I915_GTT_PAGE_SIZE (Chris)
v3: Use i915_gem_object_get_dma_address() (Chris)
Trim the sg (Tvrtko)
v4: Actually trim this time. Limit the max length
to one row of pages to keep things simple
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190509122159.24376-2-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Chris Wilson [Wed, 15 May 2019 13:00:52 +0000 (14:00 +0100)]
drm/i915/execlists: Drop promotion on unsubmit
With the disappearance of NEWCLIENT, we no longer need to provide the
priority boost on preemption in order to prevent repeated gazumping,
and we can remove the dead code.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190515130052.4475-5-chris@chris-wilson.co.uk
Chris Wilson [Wed, 15 May 2019 13:00:51 +0000 (14:00 +0100)]
drm/i915: Downgrade NEWCLIENT to non-preemptive
Commit
1413b2bc0717 ("drm/i915: Trim NEWCLIENT boosting") had the
intended consequence of not allowing a sequence of work that merely
crossed into a new engine the privilege to be promoted to NEWCLIENT
status. It also had the unintended consequence of actually making
NEWCLIENT effective on heavily oversubscribed transcode machines and
impacting upon their throughput.
If we consider a client packet composed of (rcsA, rcsB, vcs) and 30 of
those clients, using the NEWCLIENT boost that will be scheduled as
rcsA x 30, (rcsB, vcs) x 30
where as before it would have been
(rcsA, rcsB, vcs) x 30
That is with NEWCLIENT only boosting the first request of each client,
we would execute all rcsA requests prior to running on the vcs engines;
acruing a lot of dead time as compared to the previous case where the
vcs engine would be started in parallel to processing the second client.
The previous patch has the effect of delaying submission until it is
required by a third party (either the user with an explicit wait, or by
another client/engine). We reduce the NEWCLIENT bump to a mere WAIT,
which has the effect of removing its preemptive grant and reducing it to
the same level as any other user interaction -- that it will not be
promoted above the interengine dependencies, and so preventing NEWCLIENTS
from starving other engines. This a large nerf to the rrul properties of
the current NEWCLIENT, but it still does give prioritised submission to
new requests from light workloads.
References:
b16c765122f9 ("drm/i915: Priority boost for new clients")
Fixes: 1413b2bc0717 ("drm/i915: Trim NEWCLIENT boosting") # customer impact
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Dmitry Rogozhkin <dmitry.v.rogozhkin@intel.com>
Cc: Dmitry Ermilov <dmitry.ermilov@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190515130052.4475-4-chris@chris-wilson.co.uk
Chris Wilson [Wed, 15 May 2019 13:00:50 +0000 (14:00 +0100)]
drm/i915: Bump signaler priority on adding a waiter
The handling of the no-preemption priority level imposes the restriction
that we need to maintain the implied ordering even though preemption is
disabled. Otherwise we may end up with an AB-BA deadlock across multiple
engine due to a real preemption event reordering the no-preemption
WAITs. To resolve this issue we currently promote all requests to WAIT
on unsubmission, however this interferes with the timeslicing
requirement that we do not apply any implicit promotion that will defeat
the round-robin timeslice list. (If we automatically promote the active
request it will go back to the head of the queue and not the tail!)
So we need implicit promotion to prevent reordering around semaphores
where we are not allowed to preempt, and we must avoid implicit
promotion on unsubmission. So instead of at unsubmit, if we apply that
implicit promotion on adding the dependency, we avoid the semaphore
deadlock and we also reduce the gains made by the promotion for user
space waiting. Furthermore, by keeping the earlier dependencies at a
higher level, we reduce the search space for timeslicing without
altering runtime scheduling too badly (no dependencies at all will be
assigned a higher priority for rrul).
v2: Limit the bump to external edges (as originally intended) i.e.
between contexts and out to the user.
Testcase: igt/gem_concurrent_blit
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190515130052.4475-3-chris@chris-wilson.co.uk
Chris Wilson [Fri, 17 May 2019 10:22:25 +0000 (11:22 +0100)]
drm/i915/hdcp: Use both bits for device_count
Smatch spotted:
drivers/gpu/drm/i915//intel_hdcp.c:1406 hdcp2_authenticate_repeater_topology() warn: should this be a bitwise op?
and indeed looks to be suspect that we do need to use a bitwise or to
combine the two register fields into one counter.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190517102225.3069-3-chris@chris-wilson.co.uk
Chris Wilson [Fri, 17 May 2019 10:22:24 +0000 (11:22 +0100)]
drm/i915/dp: Initialise locals for static analysis
Just to squelch an smatch warning that doesn't see the with_() being
taken unconditionally:
drivers/gpu/drm/i915//intel_dp.c:230 intel_dp_get_fia_supported_lane_count() error: uninitialized symbol 'lane_info'.
drivers/gpu/drm/i915//intel_dp.c:5338 intel_digital_port_connected() error: uninitialized symbol 'is_connected'.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190517102225.3069-2-chris@chris-wilson.co.uk
Chris Wilson [Wed, 15 May 2019 13:00:49 +0000 (14:00 +0100)]
drm/i915: Truly bump ready tasks ahead of busywaits
In commit
b7404c7ecb38 ("drm/i915: Bump ready tasks ahead of
busywaits"), I tried cutting a corner in order to not install a signal
for each of our dependencies, and only listened to requests on which we
were intending to busywait. The compromise that was made was that
instead of then being able to promote the request with a full
NOSEMAPHORE like its non-busywaiting brethren, as we had not ensured we
had cleared the semaphore chain, we settled for only using the NEWCLIENT
boost. With an over saturated system with multiple NEWCLIENTS in flight
at any time, this was found to be an inadequate promotion and left us
with a much poorer scheduling order than prior to using semaphores.
The outcome of this patch, is that all requests have NOSEMAPHORE
priority when they have no dependencies and are ready to run and not
busywait, restoring the pre-semaphore ordering on saturated systems.
We can demonstrate the effect of poor scheduling order by oversaturating
the system using gem_wsim on a system with multiple vcs engines
(i.e running the same workloads across more clients than required for
peak throughput, e.g. media_load_balance_17i7.wsim -c4 -b context):
x v5.1 (normalized)
+ tip
* fix
+------------------------------------------------------------------------+
| x |
| x |
| x |
| x |
| %x |
| %%x |
| %%x |
| %%x |
| %%x |
| %%x |
| %%x |
| %%x |
| %%x |
| %%x |
| %%x |
| %#x |
| %#x |
| %#x |
| %#x |
| %#x |
| + %#xx |
| + %#xx |
| + %%#xx |
| + %%#xx |
| + %%#xx |
| + %%#xx |
| + %%##x |
| +++ %%##x |
| +++ %%##x |
| +++ %%##x |
| ++++ %%##x |
| ++++ %%##x |
| ++++ %%##xx |
| ++++ %###xx |
| ++++ %###xx |
| ++++ %###xx |
| ++++ %###xx |
| ++++ + %#O#xx |
| ++++ + %#O#xx |
| ++++++ + %#O#xx |
| ++++++++++ %OOOxxx|
| ++++++++++ + %#OOO#xx|
| + ++++++++++++ ++ +++++ + ++ @@OOOO#xx|
| |A_| |
||__________M_______A____________________| |
| |A_| |
+------------------------------------------------------------------------+
N Min Max Median Avg Stddev
x 120 0.99456 1.00628 0.999985 1.
0001545 0.
0024387139
+ 120 0.873021 1.00037 0.884134 0.
90148752 0.
039190862
Difference at 99.5% confidence
-0.098667 +/- 0.
0110762
-9.86517% +/- 1.10745%
(Student's t, pooled s = 0.
0277657)
% 120 0.990207 1.00165 0.
9970265 0.
99699748 0.
0021024
Difference at 99.5% confidence
-0.003157 +/- 0.
000908245
-0.315651% +/- 0.
0908105%
(Student's t, pooled s = 0.
00227678)
Fixes: b7404c7ecb38 ("drm/i915: Bump ready tasks ahead of busywaits")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Dmitry Rogozhkin <dmitry.v.rogozhkin@intel.com>
Cc: Dmitry Ermilov <dmitry.ermilov@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190515130052.4475-2-chris@chris-wilson.co.uk
Chris Wilson [Wed, 15 May 2019 13:00:48 +0000 (14:00 +0100)]
drm/i915: Mark semaphores as complete on unsubmit out if payload was started
Avoid charging us for the presumed busywait if the request was preempted
after successfully using semaphores to reduce inter-engine latency.
v2: Bump the priority to reflect the lack of semaphores now required.
References:
ca6e56f654e7 ("drm/i915: Disable semaphore busywaits on saturated systems")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190515130052.4475-1-chris@chris-wilson.co.uk
Imre Deak [Thu, 9 May 2019 17:34:46 +0000 (20:34 +0300)]
drm/i915: Assert that TypeC ports are not used for eDP
Add an assert that we don't use TypeC ports for eDP. That may in theory
be possible on TypeC legacy ports, but I'm not sure if that's a
practical scenario, so let's deal with that only if there's a use case.
Adding support for that wouldn't be too difficult, since TypeC mode
switching is not possible on TypeC legacy ports.
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190509173446.31095-12-imre.deak@intel.com
Imre Deak [Thu, 9 May 2019 17:34:45 +0000 (20:34 +0300)]
drm/i915: Avoid taking the PPS lock for non-eDP/VLV/CHV
On ICL we have to make sure that we enable the AUX power domain in a
controlled way (corresponding to the port's actual TypeC mode). Since
the PPS lock - which takes an AUX power ref - is only needed on
eDP on all platforms and eDP/DP on VLV/CHV avoid taking it in all
other cases.
v2:
- Clarify commit log about the condition for taking the PPS lock.
(Ville)
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190509173446.31095-11-imre.deak@intel.com
Imre Deak [Thu, 9 May 2019 17:34:44 +0000 (20:34 +0300)]
drm/i915: Replace use of PLLS power domain with DISPLAY_CORE domain
There isn't a separate power domain specific to PLLs. When programming
them we require the same power domain to be enabled which is needed when
accessing other display core parts (not specific to any
pipe/port/transcoder). This corresponds to the DISPLAY_CORE domain added
previously in this patchset, so use that instead to save bits in the
power domain mask.
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190509173446.31095-10-imre.deak@intel.com
Imre Deak [Thu, 9 May 2019 17:34:43 +0000 (20:34 +0300)]
drm/i915: Remove the unneeded AUX power ref from intel_dp_hpd_pulse()
The power get/put was added in
commit
1c767b339b39 ("drm/i915: take display port power domain in DP HPD handler")
Author: Imre Deak <imre.deak@intel.com>
Date: Mon Aug 18 14:42:42 2014 +0300
to account for the HW access in ibx_digital_port_connected(). This
latter call was in turn removed in
commit
7d23e3c37bb3 ("drm/i915: Cleaning up intel_dp_hpd_pulse")
Author: Shubhangi Shrivastava <shubhangi.shrivastava@intel.com>
Date: Wed Mar 30 18:05:23 2016 +0530
after which we didn't actually need the power reference.
One way we are accessing the HW during HPD pulse handling is via DP AUX
transfers, but the transfer function takes its own reference, so doesn't
need the reference in intel_dp_hpd_pulse().
The other spot is in
intel_psr_short_pulse()->intel_psr_disable_locked()
but that can only happen when the panel is enabled with the
corresponding modeset already holding the required power reference.
v2:
- Remove the unneeded power get/put from intel_psr_disable_locked().
(Ville)
- Checkpatch commit quoting format fix in the commit log.
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190509173446.31095-9-imre.deak@intel.com
Imre Deak [Thu, 9 May 2019 17:34:42 +0000 (20:34 +0300)]
drm/i915: Remove the unneeded AUX power ref from intel_dp_detect()
We don't need the AUX power for the whole duration of the detect, only
when we're doing AUX transfers. The AUX transfer function takes its own
reference on the AUX power domain already. The two places during detect
which access display core registers (not specific to a
pipe/port/transcoder) only need the power domain that is required for
that access. That power domain is equivalent to the device global power
domain on most platforms (enabled whenever we hold a runtime PM
reference) except on CHV/VLV where it's equivalent to the display power
well.
Add a new power domain that reflects the above, and use this at the two
spots accessing registers. With that we can avoid taking the AUX
reference for the whole duration of the detect function.
Put the domains asynchronously to avoid the unneeded on-off-on toggling.
Also adapt the idea from with_intel_runtime_pm et al. for making it easy
to write short sequences where a display power ref is needed.
v2: (Ville)
- Add with_intel_display_power() helper to simplify things.
- s/bool res/bool is_connected/
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190509173446.31095-8-imre.deak@intel.com
Imre Deak [Thu, 9 May 2019 17:34:41 +0000 (20:34 +0300)]
drm/i915: WARN for eDP encoders in intel_dp_detect_dpcd()
We are not calling this function for eDP, so add an early assert about
this for clarity.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190509173446.31095-7-imre.deak@intel.com
Imre Deak [Thu, 9 May 2019 17:34:40 +0000 (20:34 +0300)]
drm/i915: Disable power asynchronously during DP AUX transfers
In a follow-up patch we will restrict holding the reference on the AUX
power domain to the AUX transfer function. To avoid the unnecessary
on-off-on power togglings drop the reference asynchronously.
There is no reason we couldn't do this in general and also put the
reference asynchronously in pps_unlock(); but that's a separate change
that can be done as a follow-up.
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190509173446.31095-6-imre.deak@intel.com
Imre Deak [Mon, 13 May 2019 19:25:33 +0000 (22:25 +0300)]
drm/i915: Add support for asynchronous display power disabling
By disabling a power domain asynchronously we can restrict holding a
reference on that power domain to the actual code sequence that
requires the power to be on for the HW access it's doing, by also
avoiding unneeded on-off-on togglings of the power domain (since the
disabling happens with a delay).
One benefit is potential power saving due to the following two reasons:
1. The fact that we will now be holding the reference only for the
necessary duration by the end of the patchset. While simply not
delaying the disabling has the same benefit, it has the problem that
frequent on-off-on power switching has its own power cost (see the 2.
point below) and the debug trace for power well on/off events will
cause a lot of dmesg spam (see details about this further below).
2. Avoiding the power cost of freuqent on-off-on power switching. This
requires us to find the optimal disabling delay based on the measured
power cost of on->off and off->on switching of each power well vs.
the power of keeping the given power well on.
In this patchset I'm not providing this optimal delay for two
reasons:
a) I don't have the means yet to perform the measurement (with high
enough signal-to-noise ratio, or with the help of an energy
counter that takes switching into account). I'm currently looking
for a way to measure this.
b) Before reducing the disabling delay we need an alternative way for
debug tracing powerwell on/off events. Simply avoiding/throttling
the debug messages is not a solution, see further below.
Note that even in the case where we can't measure any considerable
power cost of frequent on-off switching of powerwells, it still would
make sense to do the disabling asynchronously (with 0 delay) to avoid
blocking on the disabling. On VLV I measured this disabling time
overhead to be 1ms on average with a worst case of 4ms.
In the case of the AUX power domains on ICL we would also need to keep
the sequence where we hold the power reference short, the way it would
be by the end of this patchset where we hold it only for the actual AUX
transfer. Anything else would make the locking we need for ICL TypeC
ports (whenever we hold a reference on any AUX power domain) rather
problematic, adding for instance unnecessary lockdep dependencies to
the required TypeC port lock.
I chose the disabling delay to be 100msec for now to avoid the unneeded
toggling (and so not to introduce dmesg spamming) in the DP MST sideband
signaling code. We could optimize this delay later, once we have the
means to measure the switching power cost (see above).
Note that simply removing/throttling the debug tracing for power well
on/off events is not a solution. We need to know the exact spots of
these events and cannot rely only on incorrect register accesses caught
(due to not holding a wakeref at the time of access). Incorrect
powerwell enabling/disabling could lead to other problems, for instance
we need to keep certain powerwells enabled for the duration of modesets
and AUX transfers.
v2:
- Clarify the commit log parts about power cost measurement and the
problem of simply removing/throttling debug tracing. (Chris)
- Optimize out local wakeref vars at intel_runtime_pm_put_raw() and
intel_display_power_put_async() call sites if
CONFIG_DRM_I915_DEBUG_RUNTIME_PM=n. (Chris)
- Rebased on v2 of the wakeref w/o power-on guarantee patch.
- Add missing docbook headers.
v3:
- Checkpatch spelling/missing-empty-line fix.
v4:
- Fix unintended local wakeref var optimization when using
call-arguments with side-effects, by using inline funcs instead of
macros. In this patch in particular this will fix the
intel_display_power_grab_async_put_ref()->intel_runtime_pm_put_raw()
call).
No size change in practice (would be the same disregarding the
corresponding change in intel_display_power_grab_async_put_ref()):
$ size i915-macro.ko
text data bss dec hex filename
2455190 105890 10272
2571352 273c58 i915-macro.ko
$ size i915-inline.ko
text data bss dec hex filename
2455195 105890 10272
2571357 273c5d i915-inline.ko
Kudos to Stan for reporting the raw-wakeref WARNs this issue caused. His
config has CONFIG_DRM_I915_DEBUG_RUNTIME_PM=n, which I didn't retest
after v1, and we are also not testing this config in CI.
Now tested both with CONFIG_DRM_I915_DEBUG_RUNTIME_PM=y/n on ICL,
connecting both Chamelium and regular DP, HDMI sinks.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190513192533.12586-1-imre.deak@intel.com
Imre Deak [Thu, 9 May 2019 17:34:38 +0000 (20:34 +0300)]
drm/i915: Verify power domains state during suspend in all cases
There is no reason why we couldn't verify the power domains state during
suspend in all cases, so do that. I overlooked this when originally
adding the check.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190509173446.31095-4-imre.deak@intel.com
Imre Deak [Thu, 9 May 2019 17:34:37 +0000 (20:34 +0300)]
drm/i915: Force printing wakeref tacking during pm_cleanup
Make sure we print and drop the wakeref tracking info during pm_cleanup
even if there are wakeref holders (either raw-wakeref or wakelock
holders). Dropping the wakeref tracking means that a late put on the ref
will WARN since the wakeref will be unknown, but that is rightly so,
since the put is late and we want to catch that case.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190509173446.31095-3-imre.deak@intel.com
Imre Deak [Thu, 9 May 2019 17:34:36 +0000 (20:34 +0300)]
drm/i915: Add support for tracking wakerefs w/o power-on guarantee
It's useful to track runtime PM refs that don't guarantee a device
power-on state to the rest of the driver. One such case is holding a
reference that will be put asynchronously, during which normal users
without their own reference shouldn't access the HW. A follow-up patch
will add support for disabling display power domains asynchronously
which needs this.
For this we can split wakeref_count into a low half-word tracking
all references (raw-wakerefs) and a high half-word tracking
references guaranteeing a power-on state (wakelocks).
Follow-up patches will make use of the API added here.
While at it add the missing docbook header for the unchecked
display-power and runtime_pm put functions.
No functional changes, except for printing leaked raw-wakerefs
and wakelocks separately in intel_runtime_pm_cleanup().
v2:
- Track raw wakerefs/wakelocks in the low/high half-word of
wakeref_count, instead of adding a new counter. (Chris)
v3:
- Add a struct_member(T, m) helper instead of open-coding it. (Chris)
- Checkpatch indentation formatting fix.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190509173446.31095-2-imre.deak@intel.com
Imre Deak [Fri, 10 May 2019 14:02:55 +0000 (17:02 +0300)]
drm/i915/icl: More workaround for port F detection due to broken VBTs
Add another ICL-Y PCIID that proved to have only 5 ports to the
corresponding PCIID list.
Meanwhile I'm trying to get a complete list of all PCIIDs with less than
6 ports and/or get a VBT fix to mark these ports non-existent, but until
then the only way is to go one-by-one.
This fixes the following error on machines with less than 6 port:
[drm:intel_power_well_enable [i915]] enabling AUX F
------------[ cut here ]------------
WARN_ON(intel_wait_for_register(&dev_priv->uncore, regs->driver, (0x1 << ((pw_idx) * 2)), (0x1 << ((pw_idx) * 2)), 1))
(Internal reference: BSpec/Index/20584/Issues, HSD/
1306084116)
Cc: Mika Kahola <mika.kahola@intel.com>
References: https://bugs.freedesktop.org/show_bug.cgi?id=108915
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Tested-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190510140255.25215-1-imre.deak@intel.com
Vandita Kulkarni [Thu, 2 May 2019 15:11:02 +0000 (20:41 +0530)]
drm/i915: Fix pixel clock and crtc clock config mismatch
In case of dual link mode, the mode clock that we get
from the VBT is halved.
v2: Simplify the calculation (Jani).
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1556809862-31203-4-git-send-email-vandita.kulkarni@intel.com
Vandita Kulkarni [Thu, 2 May 2019 15:11:01 +0000 (20:41 +0530)]
drm/i915: Fix pipe config mismatch for bpp, output format
Read back the pixel fomrat register and get the bpp.
v2: Read the PIPE_MISC register (Jani).
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1556809862-31203-3-git-send-email-vandita.kulkarni@intel.com
Vandita Kulkarni [Thu, 2 May 2019 15:11:00 +0000 (20:41 +0530)]
drm/i915: Refactor bdw_get_pipemisc_bpp
Move bdw_get_pipemisc_bpp alongside bdw_set_pipemisc
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1556809862-31203-2-git-send-email-vandita.kulkarni@intel.com
Vandita Kulkarni [Thu, 2 May 2019 15:10:59 +0000 (20:40 +0530)]
drm/i915: Fix the pipe state timing mismatch warnings
Adjust the get transcoder timings for mipi dsi as per the
set timing calculations.
v2: Use the existing intel_get_pipe_timings and do the dsi
specific adjustments in the encoder get_config hook.(Ville, Jani)
v3: Exclude VBLANK and HBLANK registers for dsi transcoder.
v4: Fix the incomplete conditional logic.
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1556809862-31203-1-git-send-email-vandita.kulkarni@intel.com
Ramalingam C [Mon, 13 May 2019 13:35:04 +0000 (19:05 +0530)]
drm/hdcp: drm_hdcp_request_srm() as static
Below Sparsh warnings are fixed.
Commit: drm: revocation check at drm subsystem
+drivers/gpu/drm/drm_hdcp.c:235:6: warning: symbol
'drm_hdcp_request_srm' was not declared. Should it be static?
+drivers/gpu/drm/drm_hdcp.c:27:3: warning: symbol 'srm_data' was not
declared. Should it be static?
+drivers/gpu/drm/drm_hdcp.c:317:5: warning: symbol 'drm_setup_hdcp_srm'
was not declared. Should it be static?
+drivers/gpu/drm/drm_hdcp.c:327:6: warning: symbol
'drm_teardown_hdcp_srm' was not declared. Should it be static?
cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190513133504.18612-1-ramalingam.c@intel.com
Chris Wilson [Mon, 13 May 2019 12:01:02 +0000 (13:01 +0100)]
drm/i915: Check for no-op priority changes first
In all likelihood, the priority and node are already in the CPU cache
and by checking them first, we can avoid having to chase the
*request->hwsp for the current breadcrumb.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190513120102.29660-3-chris@chris-wilson.co.uk
Chris Wilson [Mon, 13 May 2019 12:01:01 +0000 (13:01 +0100)]
drm/i915: Pass i915_sched_node around internally
To simplify the next patch, update bump_priority and schedule to accept
the internal i915_sched_ndoe directly and not expect a request pointer.
add/remove: 0/0 grow/shrink: 2/1 up/down: 8/-15 (-7)
Function old new delta
i915_schedule_bump_priority 109 113 +4
i915_schedule 50 54 +4
__i915_schedule 922 907 -15
v2: Adopt node for the old rq local, since it no longer is a request but
the origin node.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190513120102.29660-2-chris@chris-wilson.co.uk
Chris Wilson [Mon, 13 May 2019 12:01:00 +0000 (13:01 +0100)]
drm/i915: Rearrange i915_scheduler.c
To avoid pulling in a forward declaration in the next patch, move the
i915_sched_node handling to after the main dfs of the scheduler.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190513120102.29660-1-chris@chris-wilson.co.uk
Ville Syrjälä [Thu, 25 Apr 2019 16:29:06 +0000 (19:29 +0300)]
drm/i915: Add readout and state check for pch_pfit.force_thru
Convert the HSW pch_pfit.force_thru to a proper state variable
with readout and accompanying pipe conf check. Makes the logic
a bit more straightforward, and hopefully prevents some
breakage in the future.
'force_thru' is probably not the best name for this, but I
didn't manage to come up with anything better either, so I
left it alone.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190425162906.5242-2-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Ville Syrjälä [Thu, 25 Apr 2019 16:29:05 +0000 (19:29 +0300)]
drm/i915: Fix fastset vs. pfit on/off on HSW EDP transcoder
On HSW the pipe A panel fitter lives inside the display power well,
and the input MUX for the EDP transcoder needs to be configured
appropriately to route the data through the power well as needed.
Changing the MUX setting is not allowed while the pipe is active,
so we need to force a full modeset whenever we need to change it.
Currently we may end up doing a fastset which won't change the
MUX settings, but it will drop the power well reference, and that
kills the pipe.
Cc: stable@vger.kernel.org
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Fixes: d19f958db23c ("drm/i915: Enable fastset for non-boot modesets.")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190425162906.5242-1-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Daniel Drake [Tue, 23 Apr 2019 09:28:10 +0000 (17:28 +0800)]
drm/i915/fbc: disable framebuffer compression on GeminiLake
On many (all?) the Gemini Lake systems we work with, there is frequent
momentary graphical corruption at the top of the screen, and it seems
that disabling framebuffer compression can avoid this.
The ticket was reported 6 months ago and has already affected a
multitude of users, without any real progress being made. So, lets
disable framebuffer compression on GeminiLake until a solution is found.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=108085
Fixes: fd7d6c5c8f3e ("drm/i915: enable FBC on gen9+ too")
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: <stable@vger.kernel.org> # v4.11+
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190423092810.28359-1-jian-hong@endlessm.com
Ramalingam C [Tue, 7 May 2019 16:27:40 +0000 (21:57 +0530)]
drm/hdcp: gathering hdcp related code into drm_hdcp.c
Considering the significant size of hdcp related code in drm, all
hdcp related codes are moved into separate file called drm_hdcp.c.
v2:
Rebased.
v2:
Rebased.
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Suggested-by: Daniel Vetter <daniel@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190507162745.25600-7-ramalingam.c@intel.com
Ramalingam C [Tue, 7 May 2019 16:27:39 +0000 (21:57 +0530)]
drm/i915: SRM revocation check for HDCP1.4 and 2.2
DRM HDCP SRM revocation check services are used from I915 for HDCP1.4
and 2.2 revocation check during the respective authentication flow.
v2:
Rebased.
v3:
%s/*_ksvs_revocated/*_check_ksvs_revoked [Daniel]
unwanted noise is removed.
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190507162745.25600-6-ramalingam.c@intel.com
Ramalingam C [Tue, 7 May 2019 16:27:38 +0000 (21:57 +0530)]
drm: revocation check at drm subsystem
On every hdcp revocation check request SRM is read from fw file
/lib/firmware/display_hdcp_srm.bin
SRM table is parsed and stored at drm_hdcp.c, with functions exported
for the services for revocation check from drivers (which
implements the HDCP authentication)
This patch handles the HDCP1.4 and 2.2 versions of SRM table.
v2:
moved the uAPI to request_firmware_direct() [Daniel]
v3:
kdoc added. [Daniel]
srm_header unified and bit field definitions are removed. [Daniel]
locking improved. [Daniel]
vrl length violation is fixed. [Daniel]
v4:
s/__swab16/be16_to_cpu [Daniel]
be24_to_cpu is done through a global func [Daniel]
Unused variables are removed. [Daniel]
unchecked return values are dropped from static funcs [Daniel]
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Acked-by: Satyeshwar Singh <satyeshwar.singh@intel.com>
Reviewed-by: Daniel Vetter <daniel@ffwll.ch>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190507162745.25600-5-ramalingam.c@intel.com
Ramalingam C [Tue, 7 May 2019 16:27:37 +0000 (21:57 +0530)]
drm: generic fn converting be24 to cpu and vice versa
Existing functions for converting a 3bytes(be24) of big endian value
into u32 of little endian and vice versa are renamed as
s/drm_hdcp2_seq_num_to_u32/drm_hdcp_be24_to_cpu
s/drm_hdcp2_u32_to_seq_num/drm_hdcp_cpu_to_be24
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Suggested-by: Daniel Vetter <daniel@ffwll.ch>
cc: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190507162745.25600-4-ramalingam.c@intel.com
Ramalingam C [Tue, 7 May 2019 16:27:36 +0000 (21:57 +0530)]
drm/i915: debugfs: HDCP2.2 capability read
Adding the HDCP2.2 capability of HDCP src and sink info into debugfs
entry "i915_hdcp_sink_capability"
This helps the userspace tests to skip the HDCP2.2 test on non HDCP2.2
sinks.
v2:
Rebased.
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190507162745.25600-3-ramalingam.c@intel.com
Ramalingam C [Tue, 7 May 2019 16:27:35 +0000 (21:57 +0530)]
drm: move content protection property to mode_config
Content protection property is created once and stored in
drm_mode_config. And attached to all HDCP capable connectors.
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190507162745.25600-2-ramalingam.c@intel.com
Chris Wilson [Wed, 8 May 2019 11:24:52 +0000 (12:24 +0100)]
drm/i915: Seal races between async GPU cancellation, retirement and signaling
Currently there is an underlying assumption that i915_request_unsubmit()
is synchronous wrt the GPU -- that is the request is no longer in flight
as we remove it. In the near future that may change, and this may upset
our signaling as we can process an interrupt for that request while it
is no longer in flight.
CPU0 CPU1
intel_engine_breadcrumbs_irq
(queue request completion)
i915_request_cancel_signaling
... ...
i915_request_enable_signaling
dma_fence_signal
Hence in the time it took us to drop the lock to signal the request, a
preemption event may have occurred and re-queued the request. In the
process, that request would have seen I915_FENCE_FLAG_SIGNAL clear and
so reused the rq->signal_link that was in use on CPU0, leading to bad
pointer chasing in intel_engine_breadcrumbs_irq.
A related issue was that if someone started listening for a signal on a
completed but no longer in-flight request, we missed the opportunity to
immediately signal that request.
Furthermore, as intel_contexts may be immediately released during
request retirement, in order to be entirely sure that
intel_engine_breadcrumbs_irq may no longer dereference the intel_context
(ce->signals and ce->signal_link), we must wait for irq spinlock.
In order to prevent the race, we use a bit in the fence.flags to signal
the transfer onto the signal list inside intel_engine_breadcrumbs_irq.
For simplicity, we use the DMA_FENCE_FLAG_SIGNALED_BIT as it then
quickly signals to any outside observer that the fence is indeed signaled.
v2: Sketch out potential dma-fence API for manual signaling
v3: And the test_and_set_bit()
Fixes: 52c0fdb25c7c ("drm/i915: Replace global breadcrumbs with per-context interrupt tracking")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190508112452.18942-1-chris@chris-wilson.co.uk
Chris Wilson [Wed, 8 May 2019 08:06:25 +0000 (09:06 +0100)]
drm/i915/hangcheck: Replace hangcheck.seqno with RING_HEAD
After realising we need to sample RING_START to detect context switches
from preemption events that do not allow for the seqno to advance, we
can also realise that the seqno itself is just a distance along the ring
and so can be replaced by sampling RING_HEAD.
v2: Bonus comment for the mystery separate CS_STALL before MI_USER_INTERRUPT
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190508080704.24223-1-chris@chris-wilson.co.uk
Chris Wilson [Wed, 8 May 2019 11:52:45 +0000 (12:52 +0100)]
drm/i915: Reboot CI if forcewake fails
If the HW fails to ack a change in forcewake status, the machine is as
good as dead -- it may recover, but in reality it missed the mmio
updates and is now in a very inconsistent state. If it happens, we can't
trust the CI results (or at least the fails may be genuine but due to
the HW being dead and not the actual test!) so reboot the machine (CI
checks for a kernel taint in between each test and reboots if the
machine is tainted).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190508115245.27790-1-chris@chris-wilson.co.uk
Aditya Swarup [Tue, 7 May 2019 18:18:56 +0000 (11:18 -0700)]
drm/i915/icl: Fix setting 10 bit deep color mode
There is a bug in hdmi_deep_color_possible() - we compare pipe_bpp
<= 8*3 which returns true every time for hdmi_deep_color_possible 12 bit
deep color mode test in intel_hdmi_compute_config().(Even when the
requested color mode is 10 bit through max bpc property)
Comparing pipe_bpp with bpc * 3 takes care of this condition where
requested max bpc is 10 bit, so hdmi_deep_color_possible with 12 bit
returns false when requested max bpc is 10.(Ville)
v2:Add suggested by Ville Syrjälä
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Aditya Swarup <aditya.swarup@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Clinton Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190507181856.16091-1-aditya.swarup@intel.com
Ville Syrjälä [Mon, 6 May 2019 15:26:27 +0000 (18:26 +0300)]
drm/i915: Kill PCH_KBP
For us KBP is 100% identical to SPT. Kill the redundant enum
value. Also bspec doesn't talk about KBP either, so this might
avoid some confusion when cross checking the code against the
spec.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190506152627.20283-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Chris Wilson [Tue, 7 May 2019 12:29:54 +0000 (13:29 +0100)]
drm/i915/execlists: Don't apply priority boost for resets
Do not treat reset as a normal preemption event and avoid giving the
guilty request a priority boost for simply being active at the time of
reset.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190507122954.6299-1-chris@chris-wilson.co.uk
Chris Wilson [Tue, 7 May 2019 12:25:44 +0000 (13:25 +0100)]
drm/i915: Only reschedule the submission tasklet if preemption is possible
If we couple the scheduler more tightly with the execlists policy, we
can apply the preemption policy to the question of whether we need to
kick the tasklet at all for this priority bump.
v2: Rephrase it as a core i915 policy and not an execlists foible.
v3: Pull the kick together.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190507122544.12698-1-chris@chris-wilson.co.uk
Chris Wilson [Tue, 7 May 2019 12:11:08 +0000 (13:11 +0100)]
drm/i915: Stop spinning for DROP_IDLE (debugfs/i915_drop_caches)
If the user is racing a call to debugfs/i915_drop_caches with ongoing
submission from another thread/process, we may never end up idling the
GPU and be uninterruptibly spinning in debugfs/i915_drop_caches trying
to catch an idle moment.
Just flush the work once, that should be enough to park the system under
correct conditions. Outside of those we either have a driver bug or the
user is racing themselves. Sadly, because the user may be provoking the
unwanted situation we can't put a warn here to attract attention to a
probable bug.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190507121108.18377-4-chris@chris-wilson.co.uk
Chris Wilson [Tue, 7 May 2019 12:11:07 +0000 (13:11 +0100)]
drm/i915: Cancel retire_worker on parking
Replace the racy continuation check within retire_work with a definite
kill-switch on idling. The race was being exposed by gem_concurrent_blit
where the retire_worker would be terminated too early leaving us
spinning in debugfs/i915_drop_caches with nothing flushing the
retirement queue.
Although that the igt is trying to idle from one child while submitting
from another may be a contributing factor as to why it runs so slowly...
v2: Use the non-sync version of cancel_delayed_work(), we only need to
stop it from being scheduled as we independently check whether now is
the right time to be parking.
Testcase: igt/gem_concurrent_blit
Fixes: 79ffac8599c4 ("drm/i915: Invert the GEM wakeref hierarchy")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190507121108.18377-3-chris@chris-wilson.co.uk
Chris Wilson [Tue, 7 May 2019 12:11:06 +0000 (13:11 +0100)]
drm/i915: Remove delay for idle_work
The original intent for the delay before running the idle_work was to
provide a hysteresis to avoid ping-ponging the device runtime-pm. Since
then we have also pulled in some memory management and general device
management for parking. But with the inversion of the wakeref handling,
GEM is no longer responsible for the wakeref and by the time we call the
idle_work, the device is asleep. It seems appropriate now to drop the
delay and just run the worker immediately to flush the cached GEM state
before sleeping.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190507121108.18377-2-chris@chris-wilson.co.uk
Chris Wilson [Tue, 7 May 2019 12:11:05 +0000 (13:11 +0100)]
drm/i915: Flush the switch-to-kernel-context harder for DROP_IDLE
To complete the idle worker, we must complete 2 passes of wait-for-idle.
At the end of the first pass, we queue a switch-to-kernel-context and
may only idle after waiting for its completion. Speed up the flush_work
by doing the wait explicitly, which then allows us to remove the
unbounded loop trying to complete the flush_work in the next patch.
References:
79ffac8599c4 ("drm/i915: Invert the GEM wakeref hierarchy")
Testcase: igt/gem_ppgtt/flind-and-close-vma-leak
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190507121108.18377-1-chris@chris-wilson.co.uk
Clinton Taylor [Mon, 29 Apr 2019 23:08:11 +0000 (16:08 -0700)]
drm/i915/icl: Set GCP_COLOR_INDICATION only for 10/12 bit deep color
v2: Fix commit msg to reflect why issue occurs(Jani)
Set GCP_COLOR_INDICATION only when we set 10/12 bit deep color.
Changing settings from 10/12 bit deep color to 8 bit(& vice versa)
doesn't work correctly using xrandr max bpc property. When we
connect a monitor which supports deep color, the highest deep color
setting is selected; which sets GCP_COLOR_INDICATION. When we change
the setting to 8 bit color, we still set GCP_COLOR_INDICATION which
doesn't allow the switch back to 8 bit color.
v3,4: Add comments & drop changes in intel_hdmi_compute_config(Ville)
Since HSW+, GCP_COLOR_INDICATION is not required for 8bpc.
Drop the changes in intel_hdmi_compute_config as desired_bpp
is needed to change values for pipe_bpp based on bw_constrained flag.
v5: Fix missing logical && in condition for setting GCP_COLOR_INDICATION.
v6: Fix comment formatting (Ville)
v7: Add reviewed by Ville
v8: Set GCP_COLOR_INDICATION based on spec:
For Gen 7.5 or later platforms, indicate color depth only for deep
color modes. Bspec: 8135,7751,50524
Pre DDI platforms, indicate color depth if deep color is supported
by sink. Bspec: 7854
Exception: CHERRYVIEW behaves like Pre DDI platforms.
Bspec: 15975
Check pipe_bpp is less than bpp * 3 in hdmi_deep_color_possible,
to not set 12 bit deep color for every modeset. This fixes the issue
where 12 bit color was selected even when user selected 10 bit.(Ville)
v9: Maintain a consistent behavior for all platforms and support
GCP_COLOR_INDICATION only when we are in deep color mode. Remove
hdmi_sink_is_deep_color() - no longer needed as checking pipe_bpp > 24
takes care of the deep color mode scenario.
Separate patch for fixing switch from 12 bit to 10 bit deep color
mode.
Co-developed-by: Aditya Swarup <aditya.swarup@intel.com>
Signed-off-by: Clinton Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Aditya Swarup <aditya.swarup@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190429230811.9983-1-aditya.swarup@intel.com
Chris Wilson [Fri, 3 May 2019 11:52:15 +0000 (12:52 +0100)]
drm/i915: Assert the local engine->wakeref is active
Due to the asynchronous tasklet and recursive GT wakeref, it may happen
that we submit to the engine (underneath it's own wakeref) prior to the
central wakeref being marked as taken. Switch to checking the local wakeref
for greater consistency.
Fixes: 79ffac8599c4 ("drm/i915: Invert the GEM wakeref hierarchy")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190503115225.30831-3-chris@chris-wilson.co.uk
Chris Wilson [Fri, 3 May 2019 11:52:14 +0000 (12:52 +0100)]
drm/i915: Prefer checking the wakeref itself rather than the counter
The counter goes to zero at the start of the parking cycle, but the
wakeref itself is held until the end. Likewise, the counter becomes one
at the end of the unparking, but the wakeref is taken first. If we check
the wakeref instead of the counter, we include the unpark/unparking time
as intel_wakeref_is_active(), and do not spuriously declare inactive if
we fail to park (i.e. the parking and wakeref drop is postponed).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190503115225.30831-2-chris@chris-wilson.co.uk
Chris Wilson [Fri, 3 May 2019 15:22:14 +0000 (16:22 +0100)]
drm/i915: Assert breadcrumbs are correctly ordered in the signal handler
Inside the signal handler, we expect the requests to be ordered by their
breadcrumb such that no later request may be complete if we find an
earlier incomplete. Add an assert to check that the next breadcrumb
should not be logically before the current.
v2: Move the overhanging line into its own function and reuse it after
doing the insertion.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190503152214.26517-1-chris@chris-wilson.co.uk
Chris Wilson [Fri, 3 May 2019 14:02:39 +0000 (15:02 +0100)]
drm/i915: Acquire the signaler's timeline HWSP last
Acquiring the signaler's timeline takes an active reference to their
HWSP that we would like to avoid if possible, so take it after
performing all of our allocations required to set up the fencing. The
acquisition also provides the final check that the target has not
already signaled allowing us to avoid the semaphore at the last moment.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190503140239.32668-1-chris@chris-wilson.co.uk
Ville Syrjälä [Fri, 3 May 2019 19:31:43 +0000 (22:31 +0300)]
drm/i915: Move the hsw/bdw pc8 code to intel_runtime_pm.c
hsw_enable_pc8()/hsw_disable_pc8() are more less equivalent to
the display core init/unit functions of later platforms. Relocate
the hsw/bdw code into intel_runtime_pm.c so that it sits next to
its cousins.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190503193143.28240-2-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Ville Syrjälä [Fri, 3 May 2019 19:31:42 +0000 (22:31 +0300)]
drm/i915: Replace intel_ddi_pll_init()
intel_ddi_pll_init() is an anachronism. Rename it to
hsw_assert_cdclk() and move it to the power domain init code.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190503193143.28240-1-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Ville Syrjälä [Fri, 3 May 2019 17:38:07 +0000 (20:38 +0300)]
drm/i915: Move w/a 0477/WaDisableIPC:skl into intel_init_ipc()
Move the w/a to disable IPC on SKL closer to the actual code
that implements IPS. Otherwise I just end up confused as to
what is excluding SKL from considerations.
IMO this makes more sense anyway since the hw does have the
feature, we're just not supposed to use it.
And this also makes us actually disable IPC in case eg. the
BIOS enabled it when it shouldn't have.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190503173807.10834-3-ville.syrjala@linux.intel.com
Ville Syrjälä [Fri, 3 May 2019 17:38:06 +0000 (20:38 +0300)]
drm/i915: Drop WaIncreaseLatencyIPCEnabled/1140 for cnl
Drop WaIncreaseLatencyIPCEnabled/Display w/a #1140 for
early cnl steppings.
v2: Drop the IS_GEN9_BC() change since other related
parts of the code also use the KBL||CFL pattern
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190503173807.10834-2-ville.syrjala@linux.intel.com
Ville Syrjälä [Fri, 3 May 2019 17:38:05 +0000 (20:38 +0300)]
drm/i915: Document that we implement WaIncreaseLatencyIPCEnabled
Display w/a #1141 is also known as WaIncreaseLatencyIPCEnabled.
Add that to the comment.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190503173807.10834-1-ville.syrjala@linux.intel.com
Chris Wilson [Sat, 4 May 2019 07:07:07 +0000 (08:07 +0100)]
drm/i915: Disable semaphore busywaits on saturated systems
Asking the GPU to busywait on a memory address, perhaps not unexpectedly
in hindsight for a shared system, leads to bus contention that affects
CPU programs trying to concurrently access memory. This can manifest as
a drop in transcode throughput on highly over-saturated workloads.
The only clue offered by perf, is that the bus-cycles (perf stat -e
bus-cycles) jumped by 50% when enabling semaphores. This corresponds
with extra CPU active cycles being attributed to intel_idle's mwait.
This patch introduces a heuristic to try and detect when more than one
client is submitting to the GPU pushing it into an oversaturated state.
As we already keep track of when the semaphores are signaled, we can
inspect their state on submitting the busywait batch and if we planned
to use a semaphore but were too late, conclude that the GPU is
overloaded and not try to use semaphores in future requests. In
practice, this means we optimistically try to use semaphores for the
first frame of a transcode job split over multiple engines, and fail if
there are multiple clients active and continue not to use semaphores for
the subsequent frames in the sequence. Periodically, we try to
optimistically switch semaphores back on whenever the client waits to
catch up with the transcode results.
With 1 client, on Broxton J3455, with the relative fps normalized by %cpu:
x no semaphores
+ drm-tip
* patched
+------------------------------------------------------------------------+
| * |
| *+ |
| **+ |
| **+ x |
| x * +**+ x |
| x x * * +***x xx |
| x x * * *+***x *x |
| x x* + * * *****x *x x |
| + x xx+x* + *** * ********* x * |
| + x xx+x* * *** +** ********* xx * |
| * + ++++* + x*x****+*+* ***+*************+x* * |
|*+ +** *+ + +* + *++****** *xxx**********x***+*****************+*++ *|
| |__________A_____M_____| |
| |_______________A____M_________| |
| |____________A___M________| |
+------------------------------------------------------------------------+
N Min Max Median Avg Stddev
x 120 2.60475 3.50941 3.31123 3.
2143953 0.
21117399
+ 120 2.3826 3.57077 3.25101 3.
1414161 0.
28146407
Difference at 95.0% confidence
-0.
0729792 +/- 0.
0629585
-2.27039% +/- 1.95864%
(Student's t, pooled s = 0.248814)
* 120 2.35536 3.66713 3.2849 3.
2059917 0.
24618565
No difference proven at 95.0% confidence
With 10 clients over-saturating the pipeline:
x no semaphores
+ drm-tip
* patched
+------------------------------------------------------------------------+
| ++ ** |
| ++ ** |
| ++ ** |
| ++ ** |
| ++ xx *** |
| ++ xx *** |
| ++ xxx*** |
| ++ xxx*** |
| +++ xxx*** |
| +++ xx**** |
| +++ xx**** |
| +++ xx**** |
| +++ xx**** |
| ++++ xx**** |
| +++++ xx**** |
| +++++ x x****** |
| ++++++ xxx******* |
| ++++++ xxx******* |
| ++++++ xxx******* |
| ++++++ xx******** |
| ++++++ xxxx******** |
| ++++++ xxxx******** |
| ++++++++ xxxxx********* |
|+ + + + ++++++++ xxx*xx**********x* *|
| |__A__| |
| |__AM__| |
| |__A_| |
+------------------------------------------------------------------------+
N Min Max Median Avg Stddev
x 120 2.47855 2.8972 2.72376 2.
7193402 0.
074604933
+ 120 1.17367 1.77459 1.71977 1.
6966782 0.
085850697
Difference at 95.0% confidence
-1.02266 +/- 0.
0203502
-37.607% +/- 0.748352%
(Student's t, pooled s = 0.
0804246)
* 120 2.57868 3.00821 2.80142 2.
7923878 0.
058646477
Difference at 95.0% confidence
0.
0730476 +/- 0.
0169791
2.68622% +/- 0.624383%
(Student's t, pooled s = 0.
0671018)
Indicating that we've recovered the regression from enabling semaphores
on this saturated setup, with a hint towards an overall improvement.
Very similar, but of smaller magnitude, results are observed on both
Skylake(gt2) and Kabylake(gt4). This may be due to the reduced impact of
bus-cycles, where we see a 50% hit on Broxton, it is only 10% on the big
core, in this particular test.
One observation to make here is that for a greedy client trying to
maximise its own throughput, using semaphores is the right choice. It is
only the holistic system-wide view that semaphores of one client
impacts another and reduces the overall throughput where we would choose
to disable semaphores.
The most noticeable negactive impact this has is on the no-op
microbenchmarks, which are also very notable for having no cpu bus load.
In particular, this increases the runtime and energy consumption of
gem_exec_whisper.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Dmitry Rogozhkin <dmitry.v.rogozhkin@intel.com>
Cc: Dmitry Ermilov <dmitry.ermilov@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190504070707.30902-1-chris@chris-wilson.co.uk
Ville Syrjälä [Mon, 8 Apr 2019 15:27:01 +0000 (18:27 +0300)]
drm/i915: Use mul_u32_u32() more
We have a lot of '(u64)foo * bar' everywhere. Replace with
mul_u32_u32() to avoid gcc failing to use a regular 32x32->64
multiply for this.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190408152702.4153-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Ville Syrjälä [Thu, 2 May 2019 20:06:07 +0000 (23:06 +0300)]
drm/i915: Allow ICL pipe "HDR mode" when the cursor is visible
Turns out the cursor is compatible with the pipe "HDR mode". It's
only the actual SDR planes that get entirely bypassed during
blending. So let's ignore the cursor when checking if we have
any planes active that aren't HDR compatible. This fixes the
regressions in the kms_cursor_crc and kms_plane_cursor tests.
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Shashank Sharma <shashank.sharma@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=110579
Fixes: 09b25812db10 ("drm/i915: Enable pipe HDR mode on ICL if only HDR planes are used")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190502200607.14504-2-ville.syrjala@linux.intel.com
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Ville Syrjälä [Thu, 2 May 2019 20:06:06 +0000 (23:06 +0300)]
drm/i915: Move the PIPEMISC write the correct place
I fumbled the PIPEMISC write into the wrong place. It only gets
called for fastsets, but since value needs to be updated based on
the set of active planes it needs to be done for all plane updates.
Move it to the correct spot.
The symptoms include SDR planes never showing up if a previous
modeset/fastset left the pipe in HDR mode. This was immediately
obvious when running the kms_plane pixel format tests. Unfortunately
the test didn't realize it was scanning out pure black all the time
and declared success anyway.
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Shashank Sharma <shashank.sharma@intel.com>
Fixes: 09b25812db10 ("drm/i915: Enable pipe HDR mode on ICL if only HDR planes are used")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190502200607.14504-1-ville.syrjala@linux.intel.com
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Chris Wilson [Wed, 1 May 2019 11:45:36 +0000 (12:45 +0100)]
drm/i915: Delay semaphore submission until the start of the signaler
Currently we submit the semaphore busywait as soon as the signaler is
submitted to HW. However, we may submit the signaler as the tail of a
batch of requests, and even not as the first context in the HW list,
i.e. the busywait may start spinning far in advance of the signaler even
starting.
If we wait until the request before the signaler is completed before
submitting the busywait, we prevent the busywait from starting too
early, if the signaler is not first in submission port.
To handle the case where the signaler is at the start of the second (or
later) submission port, we will need to delay the execution callback
until we know the context is promoted to port0. A challenge for later.
Fixes: e88619646971 ("drm/i915: Use HW semaphores for inter-engine synchroni
sation on gen8+")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190501114541.10077-9-chris@chris-wilson.co.uk
Chris Wilson [Wed, 1 May 2019 11:45:28 +0000 (12:45 +0100)]
drm/i915/hangcheck: Track context changes
Given sufficient preemption, we may see a busy system that doesn't
advance seqno while performing work across multiple contexts, and given
sufficient pathology not even notice a change in ACTHD. What does change
between the preempting contexts is their RING, so take note of that and
treat a change in the ring address as being an indication of forward
progress.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190501114541.10077-1-chris@chris-wilson.co.uk
Chris Wilson [Thu, 2 May 2019 15:00:24 +0000 (16:00 +0100)]
drm/i915: Leave engine parking to the engines
Drop the check in GEM parking that the engines were already parked. The
intention here was that before we dropped the GT wakeref, we were sure
that no more interrupts could be raised -- however, we have already
dropped the wakeref by this point and the warning is no longer valid.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190502150024.16636-2-chris@chris-wilson.co.uk
projects / openwrt / staging / blogic.git / log