drm/pl111: Support variants with broken clock divider

The early Integrator CLCD synthesized in the Integrator CP and
IM-PD1 FPGAs are broken: their clock dividers do not work
properly. Support disabling the clock divider and drive the
clock directly from the parent under these circumstances.

Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180206093540.8147-3-linus.walleij@linaro.org

drm/pl111: Handle the Versatile RGB/BGR565 mode

The ARM Versatile series can do RGB/BGR565 with an external
"PLD" (Programmable Logical Device). However the CLCD does not
have control bits for this, so it needs to be set into the
ordinary 16BPP mode, then the RGB/BGR565 handling of the pixel
data is handled by configuring the PLD through the external
register.

Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180206093540.8147-2-linus.walleij@linaro.org

drm/pl111: Properly detect the ARM PL110 variants

With a bit of refactoring we can contain the variant data for
the strange PL110 versions that is feature-incomplete PL110 for
the ARM Integrator/CP and somewhere inbetween PL110 and PL111
for the ARM Versatile AB and Versatile PB.

We also accomodate for the custom duct-taped RGB565/BGR565 support
in the Versatile variant.

Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180206093540.8147-1-linus.walleij@linaro.org

drm/panel: Add support for ARM Versatile panels

The ARM reference designs "Versatile AB" and "Versatile PB"
contain panel connectors with autodetection of the connected
panel type. This adds a small driver utilizing the MFD syscon
look-up to read the autodetection register and set up the
corresponding panel appropriately.

In the source file there is a bit of elaboration of the
panel types and interfaces on these boards.

This was tested with the PL111 DRM driver on the ARM Versatile
AB with the IB2 daughterboard.

Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180205192013.5349-2-linus.walleij@linaro.org

drm/panel: Device tree bindings for ARM Versatile panels

This adds a pretty simple set of device tree bindings for
ARM Versatile panels appearing as child nodes of a system
controller.

Cc: devicetree@vger.kernel.org
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180205192013.5349-1-linus.walleij@linaro.org

drm/bridge: Rename argument from crtc to bridge

Why is the argument to ->mode_valid() called "crtc"?
I guess a copy/paste error. Fix it.

Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180129095531.4557-1-linus.walleij@linaro.org

drm/crc: Add support for polling on the data fd.

This will make it possible for userspace to know whether reading
will block, without blocking on the fd. This makes it possible to
drain all queued CRC's in blocking mode, without having to reopen
the fd.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180202142743.68527-1-maarten.lankhorst@linux.intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[mlankhorst: Use POLLIN|POLLRDNORM, based on Ville's suggestion]

drm/sun4i: Use drm_mode_get_hv_timing() to populate plane clip rectangle

Use drm_mode_get_hv_timing() to fill out the plane clip rectangle.

Note that this replaces crtc_state->adjusted_mode usage with
crtc_state->mode. The latter is the correct choice since that's the
mode the user provided and it matches the plane crtc coordinates
the user also provided.

Once everyone agrees on this we can move the clip handling into
drm_atomic_helper_check_plane_state().

Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180123170857.13818-2-ville.syrjala@linux.intel.com
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com> #irc

drm/rcar-du: Use drm_mode_get_hv_timing() to populate plane clip rectangle

Use drm_mode_get_hv_timing() to fill out the plane clip rectangle.

No functional changes as the code already uses crtc_state->mode
to populate the clip, which is also what drm_mode_get_hv_timing()
uses.

Once everyone agrees on this we can move the clip handling into
drm_atomic_helper_check_plane_state().

Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180123170857.13818-1-ville.syrjala@linux.intel.com
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

MAINTAINERS: Maarten for drm-misc co-maintainer

I'm stepping down, also handing all the drm-misc stuff to the new
team. Plan is that Sean handles 4.17, and Maarten then has fun with
4.18 as his first release.

Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Sean Paul <seanpaul@chromium.org>
Acked-by: Sean Paul <seanpaul@chromium.org>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Gustavo Padovan <gustavo.padovan@collabora.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180131102156.25634-1-daniel.vetter@ffwll.ch

drm/virtio: Don't return invalid caps on timeout

If the wait timeouts, the caps are probably invalid and we shouldn't be
passing them to userspace.

Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20171127142126.25765-1-tomeu.vizoso@collabora.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>

drm/edid: use true and false for boolean values

Assign true or false to boolean variables instead of an integer value.

This issue was detected with the help of Coccinelle.

Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180130100528.GA7154@training

drm/mgag200: fix a test in mga_vga_mode_valid()

The parentheses are in the wrong place here so we pass the bits per
pixel as zero.

Fixes: abbee6238775 ("drm/mgag200: Added resolution and bandwidth limits for various G200e products.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180125142655.GA23885@mwanda

drm/arcpgu: remove drm_encoder_slave

drm_encoder_slave is the old way to write bridge drivers, for i2c
bridges only. It's deprecated, and definitely should not be used in
new drivers. This has absolutely nothing to do with the new bridge
driver infrastructure implemented by drm_bridge.

What's even strange is that arcpgu doesn't even use any of this, it
really only wants a plain normal drm_encoder. Nuke all the surplus
real estate.

v2: Actually git add after compile testing ...

v3: Clarify commit message and stop including drm_encoder_slave.h.

Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180117141755.16933-1-daniel.vetter@ffwll.ch

dma-buf/sw_sync: fix document of sw_sync_create_fence_data

The structure should really be sw_sync_create_fence_data rather than
sw_sync_ioctl_create_fence which is the function name.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1515988079-8677-1-git-send-email-shawn.guo@linaro.org

drm/atomic: Remove WARN_ON for invalid plane configuration.

Userspace can set a FB_ID on a plane without setting CRTC_ID, which
will fail with -EINVAL, but the kernel shouldn't warn about that.

Same for !FB_ID and CRTC_ID being set.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180130102704.28016-1-maarten.lankhorst@linux.intel.com
Reviewed-by: Harry Wentland <harry.wentland@amd.com>

drm/bridge/synopsys: dsi: Fix dsi_host_transfer() return value

The dw_mipi_dsi_host_transfer() must return the number of
bytes transmitted/received on success instead of 0.
Note: As the read feature is not implemented, only the
transmitted number of bytes is returned for the moment.

Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Philippe Cornu <philippe.cornu@st.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180125103800.1999-3-philippe.cornu@st.com

drm/bridge/synopsys: dsi: Add a warning msg on dsi read requests

The dcs/generic dsi read feature is not yet implemented so it
is important to warn the host_transfer() caller in case of
read operation requests.

Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Philippe Cornu <philippe.cornu@st.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180125103800.1999-2-philippe.cornu@st.com

drm/stm: drv: Improve data transfers

To optimize data transfers, align pitch on 128 bytes & height
on 4 bytes. This optimization is not applicable on hw without MMU.

Signed-off-by: Yannick Fertre <yannick.fertre@st.com>
Signed-off-by: Vincent Abriou <vincent.abriou@st.com>
Signed-off-by: Philippe Cornu <philippe.cornu@st.com>
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180130104200.21602-1-philippe.cornu@st.com

drm/stm: dsi: Add 1.31 version support

Add support for the stm dsi phy/wrapper version 1.31.
Only lane capabilities need to be modified.

Signed-off-by: Philippe Cornu <philippe.cornu@st.com>
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180122164628.24728-1-philippe.cornu@st.com

dt-bindings: display: stm32: correct clock-names in dsi panel example

In the dsi panel example, clock names in the "clock-names"
field have been swapped:
* "pclk" (peripheral clock) is <&rcc 1 CLK_F469_DSI> on stm32f4
* "ref" (dsi phy pll ref clock) is <&clk_hse> on stm32f4

Signed-off-by: Philippe Cornu <philippe.cornu@st.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180122153547.23470-1-philippe.cornu@st.com

drm/atomic: Fix memleak on ERESTARTSYS during non-blocking commits

During a non-blocking commit, it is possible to return before the
commit_tail work is queued (-ERESTARTSYS, for example).

Since a reference on the crtc commit object is obtained for the pending
vblank event when preparing the commit, the above situation will leave
us with an extra reference.

Therefore, if the commit_tail worker has not consumed the event at the
end of a commit, release it's reference.

Changes since v1:
- Also check for state->event->base.completion being set, to
  handle the case where stall_checks() fails in setup_crtc_commit().
Changes since v2:
- Add a flag to drm_crtc_commit, to prevent dereferencing a freed event.
  i915 may unreference the state in a worker.

Fixes: 24835e442f28 ("drm: reference count event->completion")
Cc: <stable@vger.kernel.org> # v4.11+
Signed-off-by: Leo (Sunpeng) Li <sunpeng.li@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com> #v1
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180117115108.29608-1-maarten.lankhorst@linux.intel.com
Reviewed-by: Sean Paul <seanpaul@chromium.org>

drm/i915: Provide a device level .mode_valid() hook

We never support certain mode flags etc. Reject those early on in the
mode_config.mode_valid() hook. That allows us to remove some duplicated
checks from the connector .mode_valid() hooks, and it guarantees that
we never see those flags even from user mode as the
mode_config.mode_valid() hooks gets executed for those as well.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171114183258.16976-11-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/modes: Provide global mode_valid hook

Allow drivers to provide a device wide .mode_valid() hook in addition to
the already existing crtc/encoder/bridge/connector hooks. This can be
used to validate device/driver wide constraings without having to add
those to the other hooks. And since we call this hook also for user
modes later on in the modeset we don't have to worry about anything the
hook has already rejected.

I also have some further ideas for this hook. Eg. we could replace the
drm_mode_set_crtcinfo(HALVE_V) call in drm_mode_convert_umode()/etc.
with a driver specific variant via this hook. At least on i915 we would
like to pass CRTC_STEREO_DOUBLE to that function instead, and then
we could safely use the crtc_ timings in all our .mode_valid() hooks,
which would allow us to reuse those hooks for validating the
adjusted_mode during a modeset.

v2: Fix the language fails in the kernel docs (Daniel)

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171114183258.16976-10-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/uapi: Deprecate nonsense kms mode types

BUILTIN, CRTC_C, CLOCK_C, and DEFULT mode types are unused. Let's
refuse to generate them or accept them from userspace either. A
cursory check didn't reveal any userspace code that would depend
on these.

v2: Recommend DRIVER instead of BUILTIN (ajax)

Cc: Jose Abreu <Jose.Abreu@synopsys.com>
Cc: Adam Jackson <ajax@redhat.com>
Cc: Keith Packard <keithp@keithp.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171115154504.14338-1-ville.syrjala@linux.intel.com
Reviewed-by: Jose Abreu <joabreu@synopsys.com>

drm/modes: Kill DRM_MODE_TYPE_CLOCK_CRTC_C define

No idea what the DRM_MODE_TYPE_CLOCK_CRTC_C define is supposed to
achieve. Totally unused so kill if off.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171114183258.16976-8-ville.syrjala@linux.intel.com
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>

drm/modes: Kill off the oddball DRM_MODE_TYPE_CRTC_C vs. DRM_MODE_TYPE_BUILTIN handling

For some reason drm_mode_set_crtcinfo() does nothing if the mode has
the DRM_MODE_TYPE_BUILTIN flag set without the other bit from
DRM_MODE_TYPE_CRTC_C also set. I have zero idea what that is supposed
to achieve, but since we have no users for neither flag bit let's kill
this nonsense off.

v2: Fix typo in commit message

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171114183258.16976-7-ville.syrjala@linux.intel.com
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>

drm/modes: Fix description of DRM_MODE_TYPE_USERDEF

These days DRM_MODE_TYPE_USERDEF is used to flag modes defined via the
kernel command line. Update the docs to reflect that fact.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171114183258.16976-6-ville.syrjala@linux.intel.com
Acked-by: Alex Deucher <alexander.deucher@amd.com>

drm/uapi: Deprecate DRM_MODE_FLAG_BCAST

Reject any mode with DRM_MODE_FLAG_BCAST. We have no code that even
checks for this flag hence it can't possibly do any good.

I think this maybe originated from fbdev where it was supposed to
indicate PAL/NTSC broadcast timings. I have no idea why those would
have to be identified by a flag rather than by just the timings
themselves. And then I assume it got copied into xfree86 for
fbdevhw, and later on it leaked into the randr protocol and kms uapi.

Since kms fbdev emulation never uses the corresponding fbdev flag
there should be no sane way for this to come back into kms via
userspace either.

Cc: Jose Abreu <Jose.Abreu@synopsys.com>
Cc: Adam Jackson <ajax@redhat.com>
Cc: Keith Packard <keithp@keithp.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171114183258.16976-5-ville.syrjala@linux.intel.com
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>

drm/uapi: Deprecate DRM_MODE_FLAG_PIXMUX

Reject any mode with DRM_MODE_FLAG_PIXMUX. We have no code that even
checks for this flag hence it can't possibly do any good.

Looks like this flag had something to do the the controller<->ramdac
interface with some ancient S3 graphics adapters. Why someone though
it would be a good idea to expose it directly to users I don't know.
And later on it got copied into the randr protocol and kms uapi.

Cc: Jose Abreu <Jose.Abreu@synopsys.com>
Cc: Adam Jackson <ajax@redhat.com>
Cc: Keith Packard <keithp@keithp.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171114183258.16976-4-ville.syrjala@linux.intel.com
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>

drm/uapi: Validate the mode flags/type

Currently userspace is allowed to feed in any king of garbage in the
high bits of the mode flags/type, as are drivers when probing modes.
Reject any mode with bogus flags/type.

Hopefully this won't break any current userspace...

v2: Split the type and flags checks to separates ifs (Chris)

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jose Abreu <Jose.Abreu@synopsys.com>
Cc: Adam Jackson <ajax@redhat.com>
Cc: Keith Packard <keithp@keithp.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171115154913.23827-1-ville.syrjala@linux.intel.com
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>

drm/modes: Move 3D stereo flag check into drm_mode_validate_basic()

Currently we don't sanity check the 3D stereo flags for modes filled out
by the kernel. Move the check from drm_mode_convert_umode() into
drm_mode_validate_basic() so that we get the same check going both ways.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171114183258.16976-2-ville.syrjala@linux.intel.com
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>

drm: Warn if plane/crtc/encoder/connector index exceeds our 32bit bitmasks

We use 32bit bitmasks to track planes/crtcs/encoders/connectors.
Naturally we can only do that if the index of those objects stays
below 32. Issue a warning whenever we exceed that limit, hopefully
prompting someone to fix the problem.

For connectors the issue is a bit more complicated as they can
be created/destroyed at runtime due to MST. So the problem is no
longer a purely theoretical programmer error. As the connector
indexes are allocated via ida, we can simply limit the maximum
value the ida is allowed to hand out. The error handling is already
in place.

v2: Return an error to the caller (Harry)
v3: Print a debug message so that we know what happened (Maarten)

Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180125133020.23845-1-ville.syrjala@linux.intel.com
Reviewed-by: Harry Wentland <harry.wentland@amd.com>

drm/sun4i: backend: Check for the number of alpha planes

Due to the way the composition is done in hardware, we can only have a
single alpha-enabled plane active at a time, placed in the second (highest
priority) pipe.

Make sure of that in our atomic_check to not end up in an impossible
scenario.

Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: https://patchwork.freedesktop.org/patch/msgid/7371f62a1385f2cbe3ed75dfca2e746338eb2286.1516617243.git-series.maxime.ripard@free-electrons.com

drm/sun4i: backend: Add support for zpos

Our various planes have a configurable zpos, that combined with the pipes
allow to configure the composition.

Since the interaction between the pipes, zpos and alphas framebuffers is
not trivial, let's just enable the zpos as an immutable property for now,
and use that zpos in our atomic_update part.

Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: https://patchwork.freedesktop.org/patch/msgid/b006853e908bd06661c5bc1f2191121523bce0e4.1516617243.git-series.maxime.ripard@free-electrons.com

drm/sun4i: backend: Set a default zpos in our reset hook

The plane state zpos value will be set only if there's an existing state
attached to the plane when creating the property.

However, this is not the case during the probe, and we therefore need to
put our default value in our reset hook.

Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: https://patchwork.freedesktop.org/patch/msgid/b6a183234f0ad5a9a58c780c9cabbe29cbf40888.1516617243.git-series.maxime.ripard@free-electrons.com

drm/sun4i: backend: Move the coord function in the shared part

The function supposed to update a plane's coordinates is called in both
branches of our function. Let's move it out the if statement.

Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: https://patchwork.freedesktop.org/patch/msgid/2cd57bcf13652109da7bd5bbe12fa1d29429f02f.1516617243.git-series.maxime.ripard@free-electrons.com

drm/sun4i: framebuffer: Add a custom atomic_check

In order to support normalized zpos, we need to call
drm_atomic_normalize_zpos in our driver's drm_mode_config_funcs'
atomic_check.

Let's duplicate the definition of drm_atomic_helper_check for now.

Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: https://patchwork.freedesktop.org/patch/msgid/67cb4ca9889e6bf29314db37127ff15eed279c53.1516617243.git-series.maxime.ripard@free-electrons.com

drm/sun4i: backend: Fix define typo

There was a typo in the width spelling of the (unused)
SUN4I_BACKEND_IYUVLINEWITDTH_REG macro. Fix it.

Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: https://patchwork.freedesktop.org/patch/msgid/6b2e872b611b733a98a38902a2197b70c725e0b9.1516617243.git-series.maxime.ripard@free-electrons.com

drm/sun4i: backend: Fix structure indentation

The sun4i_plane_desc structure was somehow indented to two tabulations
instead of one as we shoud do. Fix that.

Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: https://patchwork.freedesktop.org/patch/msgid/8a6714bddb865adfcfe2b792e406a2f10bb819bc.1516617243.git-series.maxime.ripard@free-electrons.com

drm/vc4: Use the alpha format field in drm_format_info

Now that the drm_format_info has a alpha field to tell if a format embeds
an alpha component in it, let's use it.

Cc: Eric Anholt <eric@anholt.net>
Reviewed-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: https://patchwork.freedesktop.org/patch/msgid/38d4d0a085634a0b8308e819c846b9173d4d93df.1516617243.git-series.maxime.ripard@free-electrons.com

drm/rockchip: Use the alpha format field in drm_format_info

Now that the drm_format_info has a alpha field to tell if a format embeds
an alpha component in it, let's use it.

Acked-by: Sandy huang <hjc@rock-chips.com>
Reviewed-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: https://patchwork.freedesktop.org/patch/msgid/5a217e8c93eea6f0a7f6bc5883424b47dbb6c664.1516617243.git-series.maxime.ripard@free-electrons.com

drm/atmel-exynos: Use the alpha format field in drm_format_info

Now that the drm_format_info has a alpha field to tell if a format embeds
an alpha component in it, let's use it.

Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Seung-Woo Kim <sw0312.kim@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Reviewed-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: https://patchwork.freedesktop.org/patch/msgid/cb1bdfbb481419a17cc4f6c8a1f07930136ac13f.1516617243.git-series.maxime.ripard@free-electrons.com

drm/atmel-hlcdc: Use the alpha format field in drm_format_info

Now that the drm_format_info has a alpha field to tell if a format embeds
an alpha component in it, let's use it.

Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: https://patchwork.freedesktop.org/patch/msgid/23518426a46320dd884465cebec0961f839f2972.1516617243.git-series.maxime.ripard@free-electrons.com

drm/fourcc: Add a alpha field to drm_format_info

There's a bunch of drivers that duplicate the same function to know if a
particular format embeds an alpha component or not.

Let's create a field in the drm_format_info to avoid duplicating that logic
and looking up formats all the time.

Cc: Eric Anholt <eric@anholt.net>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Mark Yao <mark.yao@rock-chips.com>
Cc: Seung-Woo Kim <sw0312.kim@samsung.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: https://patchwork.freedesktop.org/patch/msgid/9cd9951d147ff810c1f6f68d79e7983361ed6b68.1516617243.git-series.maxime.ripard@free-electrons.com

drm/stm: ltdc: use crtc_mode_fixup to update adjusted_mode clock

There is a difference between the panel/bridge requested pixel clock
value and the real one due to the hw platform clock preciseness (pll,
dividers...). This patch updates the adjusted_mode clock value with
the real hw clock value so then attached encoder & connector can use
it for precise timing computations.

Signed-off-by: Philippe Cornu <philippe.cornu@st.com>
Reviewed-by: Yannick Fertré <yannick.fertre@st.com>
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180125160101.9102-1-philippe.cornu@st.com

drm/dp: Add definitions for TPS4 bits and macros to check the support

DP 1.4 spec adds a TPS4 training pattern sequence required for
HBR3. This patch adds the corresponding bit definitions in
MAX_DOWNSPREAD register and TRAINING_PATTERN_SET and
inline functions to check if this bit is set and for selecting
a proper TRAINING_PATTERN_MASK that changed to 0x7 on
DP spec 1.4

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1516660991-20697-2-git-send-email-manasi.d.navare@intel.com

drm/dp: Add HBR3 support in existing DRM DP helpers

Existing helpers add support upto HBR2. This patch
adds support for HBR3 rate (8.1 Gbps) introduced as
part of DP 1.4 specification.

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1516660991-20697-1-git-send-email-manasi.d.navare@intel.com

dma-buf: make returning the exclusive fence optional

Change reservation_object_get_fences_rcu to make the exclusive fence
pointer optional.

If not specified the exclusive fence is put into the fence array as
well.

This is helpful for a couple of cases where we need all fences in a
single array.

Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180110125341.3618-1-christian.koenig@amd.com

drm/zte: Use drm_mode_get_hv_timing() to populate plane clip rectangle

Use drm_mode_get_hv_timing() to fill out the plane clip rectangle.

Note that this replaces crtc_state->adjusted_mode usage with
crtc_state->mode. The latter is the correct choice since that's the
mode the user provided and it matches the plane crtc coordinates
the user also provided.

Once everyone agrees on this we can move the clip handling into
drm_atomic_helper_check_plane_state().

Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171123190502.28449-15-ville.syrjala@linux.intel.com
Acked-by: Shawn Guo <shawnguo@kernel.org>
Reviewed-by: Thierry Reding <treding@nvidia.com>

drm/vmwgfx: Use drm_mode_get_hv_timing() to populate plane clip rectangle

Use drm_mode_get_hv_timing() to fill out the plane clip rectangle.

Note that this replaces crtc_state->adjusted_mode usage with
crtc_state->mode. The latter is the correct choice since that's the
mode the user provided and it matches the plane crtc coordinates
the user also provided.

Once everyone agrees on this we can move the clip handling into
drm_atomic_helper_check_plane_state().

Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: VMware Graphics <linux-graphics-maintainer@vmware.com>
Cc: Sinclair Yeh <syeh@vmware.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171123190502.28449-14-ville.syrjala@linux.intel.com
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>

drm/tegra/dc: Use drm_mode_get_hv_timing() to populate plane clip rectangle

Use drm_mode_get_hv_timing() to fill out the plane clip rectangle.

No functional changes as the code already uses crtc_state->mode
to populate the clip, which is also what drm_mode_get_hv_timing()
uses.

Once everyone agrees on this we can move the clip handling into
drm_atomic_helper_check_plane_state().

v2: Rebase due to tegra_plane_state_add() relocating to plane.c

Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171123190502.28449-13-ville.syrjala@linux.intel.com

drm/rockchip: Use drm_mode_get_hv_timing() to populate plane clip rectangle

Use drm_mode_get_hv_timing() to fill out the plane clip rectangle.

Note that this replaces crtc_state->adjusted_mode usage with
crtc_state->mode. The latter is the correct choice since that's the
mode the user provided and it matches the plane crtc coordinates
the user also provided.

Once everyone agrees on this we can move the clip handling into
drm_atomic_helper_check_plane_state().

Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Mark Yao <mark.yao@rock-chips.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171123190502.28449-12-ville.syrjala@linux.intel.com
Reviewed-by: Thierry Reding <treding@nvidia.com>

drm/nouveau/kms/nv50: Use drm_mode_get_hv_timing() to populate plane clip rectangle

Use drm_mode_get_hv_timing() to fill out the plane clip rectangle.

No functional changes as the code already uses crtc_state->mode
to populate the clip, which is also what drm_mode_get_hv_timing()
uses.

Once everyone agrees on this we can move the clip handling into
drm_atomic_helper_check_plane_state().

Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: nouveau@lists.freedesktop.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171123190502.28449-11-ville.syrjala@linux.intel.com
Reviewed-by: Thierry Reding <treding@nvidia.com>

drm/msm/mdp5: Use drm_mode_get_hv_timing() to populate plane clip rectangle

Use drm_mode_get_hv_timing() to fill out the plane clip rectangle.

Note that this replaces crtc_state->adjusted_mode usage with
crtc_state->mode. The latter is the correct choice since that's the
mode the user provided and it matches the plane crtc coordinates
the user also provided.

Once everyone agrees on this we can move the clip handling into
drm_atomic_helper_check_plane_state().

Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171123190502.28449-10-ville.syrjala@linux.intel.com
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Reviewed-by: Thierry Reding <treding@nvidia.com>

drm/meson: Use drm_mode_get_hv_timing() to populate plane clip rectangle

Use drm_mode_get_hv_timing() to fill out the plane clip rectangle.

No functional changes as the code already uses crtc_state->mode
to populate the clip, which is also what drm_mode_get_hv_timing()
uses.

Once everyone agrees on this we can move the clip handling into
drm_atomic_helper_check_plane_state().

Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: linux-amlogic@lists.infradead.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171123190502.28449-9-ville.syrjala@linux.intel.com
Reviewed-by: Thierry Reding <treding@nvidia.com>

drm/mediatek: Use drm_mode_get_hv_timing() to populate plane clip rectangle

Use drm_mode_get_hv_timing() to fill out the plane clip rectangle.

No functional changes as the code already uses crtc_state->mode
to populate the clip, which is also what drm_mode_get_hv_timing()
uses.

Once everyone agrees on this we can move the clip handling into
drm_atomic_helper_check_plane_state().

Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: CK Hu <ck.hu@mediatek.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171123190502.28449-8-ville.syrjala@linux.intel.com
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Thierry Reding <treding@nvidia.com>

drm/imx: Use drm_mode_get_hv_timing() to populate plane clip rectangle

Use drm_mode_get_hv_timing() to fill out the plane clip rectangle.

Note that this replaces crtc_state->adjusted_mode usage with
crtc_state->mode. The latter is the correct choice since that's the
mode the user provided and it matches the plane crtc coordinates
the user also provided.

Once everyone agrees on this we can move the clip handling into
drm_atomic_helper_check_plane_state().

Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171123190502.28449-7-ville.syrjala@linux.intel.com
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Thierry Reding <treding@nvidia.com>

drm/simple_kms_helper: Use drm_mode_get_hv_timing() to populate plane clip rectangle

Use drm_mode_get_hv_timing() to fill out the plane clip rectangle.

Note that this replaces crtc_state->adjusted_mode usage with
crtc_state->mode. The latter is the correct choice since that's the
mode the user provided and it matches the plane crtc coordinates
the user also provided.

Once everyone agrees on this we can move the clip handling into
drm_atomic_helper_check_plane_state().

Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171123190502.28449-6-ville.syrjala@linux.intel.com
Reviewed-by: Thierry Reding <treding@nvidia.com>

drm/arm/mali-dp: Use drm_mode_get_hv_timing() to populate plane clip rectangle

Use drm_mode_get_hv_timing() to fill out the plane clip rectangle.

Note that this replaces crtc_state->adjusted_mode usage with
crtc_state->mode. The latter is the correct choice since that's the
mode the user provided and it matches the plane crtc coordinates
the user also provided.

Once everyone agrees on this we can move the clip handling into
drm_atomic_helper_check_plane_state().

Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Brian Starkey <brian.starkey@arm.com>
Cc: Mali DP Maintainers <malidp@foss.arm.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171123190502.28449-5-ville.syrjala@linux.intel.com
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>

drm/arm/hdlcd: Use drm_mode_get_hv_timing() to populate plane clip rectangle

Use drm_mode_get_hv_timing() to fill out the plane clip rectangle.

Note that this replaces crtc_state->adjusted_mode usage with
crtc_state->mode. The latter is the correct choice since that's the
mode the user provided and it matches the plane crtc coordinates
the user also provided.

Once everyone agrees on this we can move the clip handling into
drm_atomic_helper_check_plane_state().

Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Brian Starkey <brian.starkey@arm.com>
Cc: Mali DP Maintainers <malidp@foss.arm.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171123190502.28449-4-ville.syrjala@linux.intel.com
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>

drm/i915: Use drm_mode_get_hv_timing() to populate plane clip rectangle

Use drm_mode_get_hv_timing() to fill out the plane clip rectangle.
No functional changes since pipe_src_w/h are already filled via
drm_mode_get_hv_timing().

Once everyone agrees on this we can move the clip handling into
drm_atomic_helper_check_plane_state().

Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171123190502.28449-3-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Thierry Reding <treding@nvidia.com>

drm/i915: Reject odd pipe source width with double wide/dual link

In order to guarantee that pipe_src_w/h matches the user mode h/vdisplay
we must not adjust pipe_src_w to accommodate double wide/dual link.
Instead just reject the mode outright.

This will allows us to rely on crtc_state->mode for plane clipping.

Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171123190502.28449-2-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Thierry Reding <treding@nvidia.com>

drm/sun4i: Fix build warnings in sunxi_engine.h

Fixes the following build warnings:
In file included from ../drivers/gpu/drm/sun4i/sun8i_mixer.h:18:0,
                 from ../drivers/gpu/drm/sun4i/sun8i_vi_scaler.h:13,
                 from ../drivers/gpu/drm/sun4i/sun8i_vi_scaler.c:12:
../drivers/gpu/drm/sun4i/sunxi_engine.h:36:16: warning: ‘struct drm_crtc_state’ declared inside parameter list will not be visible outside of this definition or declaration
         struct drm_crtc_state *old_state);
                ^~~~~~~~~~~~~~
../drivers/gpu/drm/sun4i/sunxi_engine.h:53:15: warning: ‘struct drm_crtc_state’ declared inside parameter list will not be visible outside of this definition or declaration
        struct drm_crtc_state *state);
               ^~~~~~~~~~~~~~
In file included from ../drivers/gpu/drm/sun4i/sun8i_mixer.h:18:0,
                 from ../drivers/gpu/drm/sun4i/sun8i_ui_scaler.h:12,
                 from ../drivers/gpu/drm/sun4i/sun8i_ui_scaler.c:12:
../drivers/gpu/drm/sun4i/sunxi_engine.h:36:16: warning: ‘struct drm_crtc_state’ declared inside parameter list will not be visible outside of this definition or declaration
         struct drm_crtc_state *old_state);
                ^~~~~~~~~~~~~~
../drivers/gpu/drm/sun4i/sunxi_engine.h:53:15: warning: ‘struct drm_crtc_state’ declared inside parameter list will not be visible outside of this definition or declaration
        struct drm_crtc_state *state);
               ^~~~~~~~~~~~~~

Fixes: 6b8562c86e24 ("drm/sun4i: engine: Create an atomic_begin
callback")
Fixes: 656e5f654903 ("drm/sun4i: engine: Add a custom crtc
atomic_check")
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180122174306.231609-1-seanpaul@chromium.org

drm/panel: panasonic-vvx10f034n00: More return value fixes

A couple more return value fixes which Philippe brought up during our
previous review.

Suggested-by: Philippe CORNU <philippe.cornu@st.com>
Reviewed-by: Philippe Cornu <philippe.cornu@st.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180117213751.54668-1-seanpaul@chromium.org

drm/sun4i: backend: Make sure we don't have a commit pending

If we try to read the backend registers while it fetches the new values, we
end up with the value of some random register instead of the one we asked
for.

In order to prevent that, let's make sure that the very first thing we do
during our atomic modesetting is to let the commit bit come to a rest.

We don't have to worry about anything else since the only time we will
trigger a new transaction is during the atomic_commit which comes much
later.

Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: https://patchwork.freedesktop.org/patch/msgid/35604307e5bde2b85c674de79fa7c4d55700f085.1516613040.git-series.maxime.ripard@free-electrons.com

drm/sun4i: backend: Use runtime_pm variant of atomic_commit_tail

During a hardware commit, the commit bit in the backend will only be
cleared if the TCON is enabled. Use the runtime_pm variant of the
atomic_commit_tail hook that makes sure that the CRTC, our TCON, is enabled
when we perform an atomic_commit.

Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: https://patchwork.freedesktop.org/patch/msgid/bde95faff2078f63e9af99c3abee5360b9050fd1.1516613040.git-series.maxime.ripard@free-electrons.com

drm/sun4i: backend: Add a custom atomic_check for the frontend

Now that we have everything in place, we can start enabling the frontend.
This is more difficult than one would assume since there can only be one
plane using the frontend per-backend.

We therefore need to make sure that the userspace will not try to setup
multiple planes using it, since that would be impossible. In order to
prevent that, we can create an atomic_check callback that will check that
only one plane will effectively make use of the frontend in a given
configuration, and will toggle the switch in that plane state so that the
proper setup function can do their role.

Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: https://patchwork.freedesktop.org/patch/msgid/278e6c514a8311750fe627c7f28d58b3e2cbd825.1516613040.git-series.maxime.ripard@free-electrons.com

drm/sun4i: backend: Wire in the frontend

Now that we have a driver, we can make use of it. This is done by
adding a flag to our custom plane state that will trigger whether we should
use the frontend on that particular plane or not.

The rest is just plumbing to set up the backend to not perform the DMA but
receive its data from the frontend.

Note that we're still not making any use of the frontend itself, as no one
is setting the flag yet.

Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: https://patchwork.freedesktop.org/patch/msgid/cdffc25eab2d817820cc78cbd24f1f4b99902014.1516613040.git-series.maxime.ripard@free-electrons.com

drm/sun4i: Add a driver for the display frontend

The display frontend is an hardware block that can be used to implement
some more advanced features like hardware scaling or colorspace
conversions. It can also be used to implement the output format of the VPU.

Let's create a minimal driver for it that will only enable the hardware
scaling features.

Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: https://patchwork.freedesktop.org/patch/msgid/029cdc3478bf89d422f5e8d9e600baf5e48ce4db.1516613040.git-series.maxime.ripard@free-electrons.com

drm/sun4i: engine: Create an atomic_begin callback

We have to implement some display engine specific behaviours in
atomic_begin. Let's add a function for that.

Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: https://patchwork.freedesktop.org/patch/msgid/44110951ae0cc13767fefc7fc1d9e2ec782d0a40.1516613040.git-series.maxime.ripard@free-electrons.com

drm/sun4i: engine: Add a VBLANK quirk callback

In some cases, the display engine needs to apply some quirks during the
VBLANK event. In the Display Engine 1.0 case for example, we can only
disable the frontend once the backend has been, which is at VBLANK.

Let's introduce a callback that can be implemented by the various engines.

Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: https://patchwork.freedesktop.org/patch/msgid/7c298d43aa1500196aa5d15d7a7c0f228c7a6f3c.1516613040.git-series.maxime.ripard@free-electrons.com

drm/sun4i: engine: Add a custom crtc atomic_check

We have some restrictions on what the planes and CRTC can provide that are
tied to only one generation of display engines.

For example, on the first generation, we can only have one YUV plane or one
plane that uses the frontend output.

Let's allow our engines to provide an atomic_check callback to validate the
current configuration.

Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: https://patchwork.freedesktop.org/patch/msgid/e5f5f144e5c20d348cdb29933ae876c105bec017.1516613040.git-series.maxime.ripard@free-electrons.com

drm/sun4i: backend: Add a custom plane state

We will need to store some additional data in the future to the state.
Create a custom plane state that will embed those data, in order to store
the pipe or whether or not that plane should use the frontend.

Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: https://patchwork.freedesktop.org/patch/msgid/88dd9c2b0caa550595e7b2ff37dc9d0af2c78609.1516613040.git-series.maxime.ripard@free-electrons.com

drm/sun4i: backend: Allow a NULL plane pointer to retrieve the format

The function converting the DRM format to its equivalent in the backend
registers was assuming that we were having a plane.

However, we might want to use that function when setting up a plane using
the frontend, in which case we will not have a plane associated to the
backend's layer. Yet, we still need to setup the format to the one output
by the frontend.

Test for NULL plane pointers before referencing them, so that we can work
around it.

Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: https://patchwork.freedesktop.org/patch/msgid/bfbe4c2e8525a7542526b648d59a8f3546e905f1.1516613040.git-series.maxime.ripard@free-electrons.com

drm/sun4i: backend: Document the engine operations

Our operations were missing some documentation to explain what was expected
from them.

Let's make that clearer.

Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: https://patchwork.freedesktop.org/patch/msgid/fdcd8ec3ae9ecd73ef089ede5218d3a41b49be05.1516613040.git-series.maxime.ripard@free-electrons.com

drm/sun4i: backend: Move line stride setup to buffer setup function

Setup the line stride in the buffer setup function, since it's tied to the
buffer itself, and is not needed when we do not set the buffer in the
backend.

This is for example the case when using the frontend and then routing its
output to the backend.

Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: https://patchwork.freedesktop.org/patch/msgid/cbec84125bc0d5a6cf1d856b8291fbf77b138881.1516613040.git-series.maxime.ripard@free-electrons.com

Merge airlied/drm-next into drm-misc-next

It's been a while since we've backmerged drm-next. Dave just brought
back 4.15-rc8, so now's a good time to freshen things up around here.

Signed-off-by: Sean Paul <seanpaul@chromium.org>

drm: add kernel doc for exported gem dmabuf_ops

Signed-off-by: Samuel Li <Samuel.Li@amd.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1516311860-24949-1-git-send-email-Samuel.Li@amd.com

drm/i2c: tda998x: Remove duplicate NULL check

Since i2c_unregister_device() became NULL-aware we may remove duplicate
NULL check.

Cc: Russell King <linux@armlinux.org.uk>
Cc: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171031142149.32512-8-andriy.shevchenko@linux.intel.com
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>

drm/i2c/sil164: Remove duplicate NULL check

Since i2c_unregister_device() became NULL-aware we may remove duplicate
NULL check.

Cc: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171031142149.32512-7-andriy.shevchenko@linux.intel.com
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>

drm/bridge: analogix-anx78xx: Remove duplicate NULL check

Since i2c_unregister_device() became NULL-aware we may remove duplicate
NULL check.

Cc: Archit Taneja <architt@codeaurora.org>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171031142149.32512-6-andriy.shevchenko@linux.intel.com
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>

BackMerge tag 'v4.15-rc8' into drm-next

Linux 4.15-rc8

Daniel requested this for so the intel CI won't fall over on drm-next
so often.

drm/panel: panasonic-vvx10f034n00: Fix wuxga_nt_panel_disable() return value

Return value for mipi_dsi_shutdown_peripheral() is unchecked.
Check it and return any errors if they come up. Even if
mipi_dsi_shutdown_peripheral() fails, continue attempting to
disable.

Cc: Philippe Cornu <philippe.cornu@st.com>
Reviewed-by: Philippe Cornu <philippe.cornu@st.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180116222217.240939-1-seanpaul@chromium.org

drm/dsi: Fix improper use of mipi_dsi_device_transfer() return value

The function mipi_dsi_device_transfer() returns the number of transmitted
or received bytes on success or a negative error code on failure.

The functions mipi_dsi_shutdown_peripheral(), mipi_dsi_turn_on_peripheral() &
mipi_dsi_set_maximum_return_packet_size() use improperly this returned
value in case of success: 0 should be returned instead of the number of
transmitted bytes.

Signed-off-by: Philippe Cornu <philippe.cornu@st.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180112144847.18810-1-philippe.cornu@st.com

drm/bridge/synopsys: dsi: handle endianness correctly in dw_mipi_dsi_write()

We're filling the "remainder" word with little-endian data, then writing
it out to IO registers with endian-correcting writel(). That probably
won't work on big-endian systems.

Let's mark the "remainder" variable as LE32 (since we fill it with
memcpy()) and do the swapping explicitly.

Some of this function could be done more easily without memcpy(), but
the unaligned "remainder" case is a little hard to do without
potentially overrunning 'tx_buf', so I just applied the same solution in
all cases (memcpy() + le32_to_cpu()).

Tested only on a little-endian system.

Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180109203248.139249-2-briannorris@chromium.org

drm/bridge/synopsys: dsi: use common mipi_dsi_create_packet()

This takes care of 2 TODOs in this driver, by using the common DSI
packet-marshalling code instead of our custom short/long write code.
This both saves us some duplicated code and gets us free support for
command types that weren't already part of our switch block (e.g.,
MIPI_DSI_GENERIC_LONG_WRITE).

The code logic stays mostly intact, except that it becomes unnecessary
to split the short/long write functions, and we have to copy data a bit
more.

Along the way, I noticed that loop bounds were a little odd:

while (DIV_ROUND_UP(len, pld_data_bytes))

This really was just supposed to be 'len != 0', so I made that more
clear.

Tested on RK3399 with some pending refactoring patches by Nickey Yang,
to make the Rockchip DSI driver wrap this common driver.

Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Philippe Cornu <philippe.cornu@st.com>
Tested-by: Philippe Cornu <philippe.cornu@st.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180109203248.139249-1-briannorris@chromium.org

drm/bridge/synopsys: dsi: make dw_mipi_dsi_bridge_mode_set() static

sparse complains:

drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c:703:6: warning: symbol
'dw_mipi_dsi_bridge_mode_set' was not declared. Should it be static?

Reviewed-by: Philippe Cornu <philippe.cornu@st.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180109203319.139520-1-briannorris@chromium.org

drm/tinydrm/mipi-dbi: Change reset active time

The MIPI DBI spec states that reset active/low time should be more
than 9us. Change from 20ms to 20us.

Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: David Lechner <david@lechnology.com>
Tested-by: David Lechner <david@lechnology.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180110185940.53841-8-noralf@tronnes.org

drm/tinydrm: Embed the mode in tinydrm_connector

Embed the mode in tinydrm_connector instead of doing an devm_ allocation.
Remove unnecessary use of ret variable at the end of
tinydrm_display_pipe_init().

Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: David Lechner <david@lechnology.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180110185940.53841-7-noralf@tronnes.org

drm/tinydrm/mi0283qt: Let the display pipe handle power

It's better to leave power handling and controller init to the
modesetting machinery using the simple pipe .enable and .disable
callbacks. Remove unused mipi_dbi_pipe_enable().

Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: David Lechner <david@lechnology.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180110185940.53841-6-noralf@tronnes.org

drm/tinydrm/mipi-dbi: Add poweron-reset functions

Split out common poweron-reset functionality.

Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: David Lechner <david@lechnology.com>
Tested-by: David Lechner <david@lechnology.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180110185940.53841-5-noralf@tronnes.org

drm/tinydrm/mipi-dbi: Add mipi_dbi_enable_flush()

Add and use a function for enabling, flushing and turning on backlight.

Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: David Lechner <david@lechnology.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180110185940.53841-4-noralf@tronnes.org

drm/tinydrm/mi0283qt: Remove ili9341.h

No need for a public header file for the command macros.
Just include the necessary ones in the driver.

Also use the MIPI_DCS_PIXEL_FMT_16BIT macro.

Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: David Lechner <david@lechnology.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180110185940.53841-3-noralf@tronnes.org

drm/tinydrm/mi0283qt: Use common include order

Include linux headers before drm headers as it's commonly done.

Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: David Lechner <david@lechnology.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180110185940.53841-2-noralf@tronnes.org

Linux 4.15-rc8

Merge branch 'x86-pti-for-linus' of git://git./linux/kernel/git/tip/tip

Pull x86 fixlet from Thomas Gleixner.

Remove a warning about lack of compiler support for retpoline that most
people can't do anything about, so it just annoys them needlessly.

* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/retpoline: Remove compile time warning

Merge tag 'powerpc-4.15-7' of git://git./linux/kernel/git/powerpc/linux

Pull powerpc fixes from Michael Ellerman:
 "One fix for an oops at boot if we take a hotplug interrupt before we
  are ready to handle it.

  The bulk is patches to implement mitigation for Meltdown, see the
  change logs for more details.

  Thanks to: Nicholas Piggin, Michael Neuling, Oliver O'Halloran, Jon
  Masters, Jose Ricardo Ziviani, David Gibson"

* tag 'powerpc-4.15-7' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/powernv: Check device-tree for RFI flush settings
  powerpc/pseries: Query hypervisor for RFI flush settings
  powerpc/64s: Support disabling RFI flush with no_rfi_flush and nopti
  powerpc/64s: Add support for RFI flush of L1-D cache
  powerpc/64s: Convert slb_miss_common to use RFI_TO_USER/KERNEL
  powerpc/64: Convert fast_exception_return to use RFI_TO_USER/KERNEL
  powerpc/64: Convert the syscall exit path to use RFI_TO_USER/KERNEL
  powerpc/64s: Simple RFI macro conversions
  powerpc/64: Add macros for annotating the destination of rfid/hrfid
  powerpc/pseries: Add H_GET_CPU_CHARACTERISTICS flags & wrapper
  powerpc/pseries: Make RAS IRQ explicitly dependent on DLPAR WQ

x86/retpoline: Remove compile time warning

Remove the compile time warning when CONFIG_RETPOLINE=y and the compiler
does not have retpoline support. Linus rationale for this is:

  It's wrong because it will just make people turn off RETPOLINE, and the
  asm updates - and return stack clearing - that are independent of the
  compiler are likely the most important parts because they are likely the
  ones easiest to target.

  And it's annoying because most people won't be able to do anything about
  it. The number of people building their own compiler? Very small. So if
  their distro hasn't got a compiler yet (and pretty much nobody does), the
  warning is just annoying crap.

  It is already properly reported as part of the sysfs interface. The
  compile-time warning only encourages bad things.

Fixes: 76b043848fd2 ("x86/retpoline: Add initial retpoline support")
Requested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: gnomes@lxorguk.ukuu.org.uk
Cc: Rik van Riel <riel@redhat.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: thomas.lendacky@amd.com
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Kees Cook <keescook@google.com>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linux-foundation.org>
Link: https://lkml.kernel.org/r/CA+55aFzWgquv4i6Mab6bASqYXg3ErV3XDFEYf=GEcCDQg5uAtw@mail.gmail.com

Merge branch 'for-linus' of git://git.kernel.dk/linux-block

Pull NVMe fix from Jens Axboe:
 "Just a single fix for nvme over fabrics that should go into 4.15"

* 'for-linus' of git://git.kernel.dk/linux-block:
  nvme-fabrics: initialize default host->id in nvmf_host_default()