qlcnic: fix promiscous mode for VF

o Allow promiscous mode setting for VF's depending upon the configuration.

Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlcnic: fix board description

Remove "Flex-10" from board description.

Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlcnic: remove private LRO flag

LRO was not getting enable after interface down/up.

Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlcnic: support quiescent mode

Put device in quiescent mode during internal loopback test.
Before running test, set state to NEED_QUISCENT. After getting
ack from all function, change state to QUISCENT and perform test.

Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlcnic: driver private workqueue

Currently fw recovery usage global workqueue.
As same workqueue used by kernel for ethtool and etc., supporting
quiescent mode is not possible, without driver private workqueue.

Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'for-davem' of git://git./linux/kernel/git/linville/wireless-next-2.6

Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-next-2.6 into for-davem

Conflicts:
Documentation/feature-removal-schedule.txt
drivers/net/wireless/ipw2x00/ipw2200.c

ipv4: Remove leftover rcu_read_unlock calls from __mkroute_output()

Commit "fib: RCU conversion of fib_lookup()" removed rcu_read_lock() from
__mkroute_output but left a couple of calls to rcu_read_unlock() in there.
This causes lockdep to complain that the rcu_read_unlock() call in
__ip_route_output_key causes a lock inbalance and quickly crashes the
kernel. The below fixes this for me.

Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sfc: Don't try to set filters with search depths we know won't work

The filter engine will time-out and ignore filters beyond
200-something hops.  We also need to avoid infinite loops in
efx_filter_search() when the table is full.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: Update kernel-doc for netif_set_real_num_rx_queues()

Synchronise the comment with the preceding implementation change.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ath9k_hw: Fix hw reset failure with HTC driver

The following commit removed DISABLE_REGWRITE_BUFFER ops. The unnecessary
REGWRITE_BUFFER_FLUSH was not removed properly which is causing failure on
hw reset.

Author: Felix Fietkau <nbd@openwrt.org>
Date:   Tue Oct 5 12:03:42 2010 +0200

    ath9k_hw: clean up register write buffering

Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: constify WDS address

There's no need for the WDS peer address
to not be const, so make it const.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

nl80211: use new genl helpers for WDS

Bill Jordan's patch to allow setting the WDS
peer crossed with my patch removing all the
boilerplate code in nl80211, and consequently
he didn't make use of it yet. Fix that.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: fix sw scan locking

The recent scan overhaul broke locking
because now we can jump to code that
attempts to unlock, while we don't have
the mutex held. Fix this by holding the
mutex around all the relevant code.

Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl1271: Support FEM autodetection

In the NVS/INI-parameters for the driver/firmware there is the FEM
(front end module) selection option, which may configure the hardware FEM
via autodetection or manual selection. So far, there has been support for
manual selection only.

Add support for FEM autodetection.

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'wireless-next-2.6' of git://git./linux/kernel/git/iwlwifi/iwlwifi-2.6

Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-2.6

Revert "mac80211: use netif_receive_skb in ieee80211_tx_status callpath"

This reverts commit 5ed3bc7288487bd4f891f420a07319e0b538b4fe.

It turns-out that not all drivers are calling ieee80211_tx_status from a
compatible context.  Revert this for now and try again later...

Signed-off-by: John W. Linville <linville@tuxdriver.com>

Revert "rtl8180: use NAPI for bottom-half processing"

This reverts commit 030725d2c7c1fafec7ede618647bf30ed79601f0.

This commit relies on commit 5ed3bc7288487bd4f891f420a07319e0b538b4fe
("mac80211: use netif_receive_skb in ieee80211_tx_status callpath")
Unfortunately not all drivers are calling ieee80211_tx_status from a
compatible context, so that commit needs to be reverted in 2.6.36.

Signed-off-by: John W. Linville <linville@tuxdriver.com>

ixgbe: Use affinity_hint when Flow Director is enabled

Use the new infrastructure to balance interrupts for flow
alignment when ATR or Flow Director are enabled.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/stmmac/: add HAS_IOMEM dependency

The stmmac driver does not compile on s390:

drivers/net/stmmac/stmmac_main.c: In function 'stmmac_adjust_link':
drivers/net/stmmac/stmmac_main.c:210: error: implicit declaration of function 'readl'
drivers/net/stmmac/stmmac_main.c:263: error: implicit declaration of function 'writel'
drivers/net/stmmac/stmmac_main.c: In function 'stmmac_dvr_probe':
drivers/net/stmmac/stmmac_main.c:1674: error: implicit declaration of function 'ioremap'
drivers/net/stmmac/stmmac_main.c:1674: warning: assignment makes pointer from integer without a cast
drivers/net/stmmac/stmmac_main.c:1761: error: implicit declaration of function 'iounmap'
make[3]: *** [drivers/net/stmmac/stmmac_main.o] Error 1

Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Giuseppe CAVALLARO <peppe.cavallaro@st.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: netif_set_real_num_rx_queues may cap num_rx_queues at init time

Do not set num_rx_queues in netif_set_real_num_rx_queues() some
drivers will increase the real_num_rx_queues later due to a feature
changes or available interrupts increasing. By setting num_rx_queues
here this ends up creating a cap on the number of rx queues
available.

For example the ixgbe driver sets the max number of queues it intends
to use ever then sets the current number in use with the
netif_set_num_{rx|tx}_queues calls. With the current implementation
the number of rx queues gets limited so when a feature such as DCB
or FCoE is enabled the queues are no longer available.

kobjects will only be allocated for real_num_rx_queues so the waste
in memory is minimal.

Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

eicon: make buffer larger

In diva_mnt_add_xdi_adapter() we do this:
  strcpy (clients[id].drvName,     tmp);
  strcpy (clients[id].Dbg.drvName, tmp);

The "clients[id].drvName" is a 128 character buffer and
"clients[id].Dbg.drvName" was originally a 16 character buffer but I've
changed it to 128 as well.  We don't actually use 128 characters but we
do use more than 16.

I've also changed the size of "tmp" to 128 characters instead of 256.

Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

dccp: Kill dead code and add static markers.

Remove dead code and make some functions static.
Compile tested only.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sundance: Drop legacy _COMPAT_WITH_OLD_KERNEL includes

Drop legacy includes since 2.4.x

Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

TCP: Fix setting of snd_ssthresh in tcp_mtu_probe_success

This looks like a simple typo that has gone unnoticed for some time.  The
impact is relatively low but it's clearly wrong.

Signed-off-by: John Heffner <johnwheffner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'master' of /linux/kernel/git/davem/net-2.6

Conflicts:
drivers/net/pcmcia/pcnet_cs.c
net/caif/caif_socket.c

Merge branch 'master' of /linux/kernel/git/torvalds/linux-2.6

bonding: add Speed/Duplex information to /proc/net/bonding/bond

Effect:
 Slave Interface: eth5
 MII Status: up
 Speed: 10000 Mbps
 Duplex: full
 Link Failure Count: 0
 Permanent HW addr: XX:XX:XX:XX:XX:XX
 Slave queue ID: 0

Signed-off-by: Krzysztof Piotr Oledzki <ole@ans.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

neigh: RCU conversion of struct neighbour

This is the second step for neighbour RCU conversion.

(first was commit d6bf7817 : RCU conversion of neigh hash table)

neigh_lookup() becomes lockless, but still take a reference on found
neighbour. (no more read_lock()/read_unlock() on tbl->lock)

struct neighbour gets an additional rcu_head field and is freed after an
RCU grace period.

Future work would need to eventually not take a reference on neighbour
for temporary dst (DST_NOCACHE), but this would need dst->_neighbour to
use a noref bit like we did for skb->_dst.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

iwlagn: add define for MODULE_FIRMWARE

Adding MODULE_FIRMWARE define for 130 series of devices

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlagn: fix module firmware name for 130 series device

130 series device should use firmware name with 130 in it.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

bonding: reread information about speed and duplex when interface goes up

When an interface was enslaved when it was down, bonding thinks
it has speed -1 even after it goes up. This leads into selecting
a wrong active interface in active/backup mode on mixed 10G/1G or
1G/100M environment.

before:
 bonding: bond0: link status definitely up for interface eth5, 100 Mbps full duplex.
 bonding: bond0: link status definitely up for interface eth0, 100 Mbps full duplex.

after:
 bonding: bond0: link status definitely up for interface eth5, 10000 Mbps full duplex.
 bonding: bond0: link status definitely up for interface eth0, 1000 Mbps full duplex.

Signed-off-by: Krzysztof Piotr Oledzki <ole@ans.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

bonding: print information about speed and duplex seen by the driver

before:
 bonding: bond0: link status definitely up for interface eth5
 bonding: bond0: link status definitely up for interface eth0

after:
 bonding: bond0: link status definitely up for interface eth5, 100 Mbps full duplex.
 bonding: bond0: link status definitely up for interface eth0, 100 Mbps full duplex.

Signed-off-by: Krzysztof Piotr Oledzki <ole@ans.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: update version to 1.60.00-1

Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: properly initialize FW stats

Client statistics need to be initialized to -1

Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: code beautify

This patch does not include any functional changes.
The changes are: empty lines, indentation and comments.

Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x, cnic: Fix SPQ return credit

Return proper L2 and L5 SPQ (slow path queue) credits.  Previously, all
SPQ events were counted as L5 types.

Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: move msix table initialization to probe()

Decide which interrupt mode to use (MSI-X, MSI, INTa) only once in probe() and
initialize appropriate structures.

Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: use L1_CACHE_BYTES instead of magic number

Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: use proper constants for dma_unmap* calls

Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: remove unused fields in main driver structure

Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: remove unused parameter in reuse_rx_skb()

Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: Add 57712 support

57712 HW supported with same set of features as for 57710/57711

Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: change type of spq_left to atomic

The field is now accessed from different contexts.

Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: rename MF related fields

MF (multi-function) mode supported not only by 57711E (E1H) devices,
but also by coming 57712E, then we use more generic names.

Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: remove old FW files

Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x, cnic, bnx2i: use new FW/HSI

This is the new FW HSI blob and the relevant definitions without logic changes.
It also included code adaptation for new HSI. New features are not enabled.

New FW/HSI includes:
- Support for 57712 HW
- Future support for VF (not used)
- Improvements in FW interrupts scheme
- FW FCoE hooks (stubs for future usage)

Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: add 6.0.34 fw files

New firmware files for all bnx2x devices

Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: create folder for bnx2x firmware files

Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

cnic: Fine-tune ring init code.

Initialize the rings only during cnic_uio_open() and shut them down
during cnic_uio_close().  Check for the new bit CNIC_LCL_FL_RINGS_INITED
before checking for ring interrupt.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

cnic: Use pfid for internal memory offsets.

The pfid (physical function ID) is the same as PCI function on production
devices.  The pfid for future devices will be different and will be used
for internal memory offsets.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

cnic: Pass cp pointer to BNX2X_HW_CID.

Preparation work for upcoming firmware interface changes.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

[PATCH net-next] tg3: Set real_num_rx_queues for non-multiq devs

Commit 2ddaad397c47de012dfb956b0c05540da1a0dde5 entitled "tg3: Use
netif_set_real_num_{rx,tx}_queues()" added a new call to
netif_set_real_num_rx_queues in tg3_enable_msix().  This call also needs
to be added to the legacy path to correctly reflect the actual number of
rx queues.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mac80211: avoid uninitialized var warning in ieee80211_scan_cancel

net/mac80211/scan.c: In function ‘ieee80211_scan_cancel’:
net/mac80211/scan.c:794: warning: ‘finish’ may be used uninitialized in this function

Signed-off-by: John W. Linville <linville@tuxdriver.com>

Linux 2.6.36-rc7

cfg80211: fix BSS double-unlinking

When multiple interfaces are actively trying
to associate with the same BSS, they may both
find that the BSS isn't there and then try to
unlink it. This can cause errors since the
unlinking code can't currently deal with items
that have already been unlinked.

Normally this doesn't happen as most people
don't try to use multiple station interfaces
that associate at the same time too.

Fix this by using the list entry as a flag to
see if the item is still on a list.

Cc: stable@kernel.org
Reported-by: Ben Greear <greearb@candelatech.com>
Tested-by: Hun-Kyi Wynn <hkwynn@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

nl80211/mac80211: Add retry and failed transmission count to station info

This information is already available in mac80211, we just need to export it
via cfg80211 and nl80211.

Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Revert "iwlwifi: do not perferm force reset while doing scan"

This reverts commit 7acc7c683a747689aaaaad4fce1683fc3f85e552. It was
applied to avoid possible warning in ieee80211_restart_hw, however
reason of the warning were races in mac80211, currently hopefully fixed.

Not reseting device when performing scan is bad for two reasons.

When forcing reset from iwl_check_stuck_queue(), in case of fail,
reset will be repeated until scan finish. But since firmware is in bad
shape, scan only finish after scan_check work (about 7s). So we will
delay the reset, what is not good behaviour.

When forcing reset from iwl_recover_from_statistics(), we will not
repeat the reset, so we will not perform reset at all when needed.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: compete scan to cfg80211 if deferred scan fail to start

We nulify local->scan_req on failure in __ieee80211_start_scan, so
__ieee80211_scan_completed will not call cfg80211_scan_done. Fix that.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: do not requeue scan work when not needed

When performing hw scan and not abort it, __ieee80211_scan_completed()
is currently called from scan work, so does not need to reschedule work
to call drv_hw_scan().

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: assure we also cancel deferred scan request

This is partial revert and fix for commit
85f72bc839705294b32b6c16b491c0422f0a71b3 "mac80211: only cancel
software-based scans on suspend"

When cfg80211 request the scan and mac80211 perform some management work,
we defer the scan request. We do not canceling such requests when calling
ieee80211_scan_cancel(), because of SCAN_SW_SCANNING bit check just
before the call. So fix that problem.

Another problem, which commit 85f72bc839705294b32b6c16b491c0422f0a71b3
tries to solve, is we can not cancel HW scan. Hence patch make
ieee80211_scan_cancel() ignore HW scan (see code comments). Keeping
local->mtx lock assures that the deferred scan will not become
"working" HW scan.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: keep lock when calling __ieee80211_scan_completed()

We are taking local->mtx inside __ieee80211_scan_completed(), but just
before call to that function we drop the lock. Dropping/taking lock is not
good, because can lead to hard to understand race conditions.

Patch split scan_completed() code into two functions, first must be called
with local->mtx taken and second without it.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: reduce number of __ieee80211_scan_completed calls

Use goto instruction to call __ieee80211_scan_completed only ones in
ieee80211_scan_work. This is prepare for the next patch.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: N-PHY: don't duplicate setting channel in shared memory

It's already set in PHY common code.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: define B43_SHM_SH_CHAN_40MHZ

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: N-PHY: simplify channel switching

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

nl80211: fix error in generic netif_running check

Yikes! The error return keeps a netdev reference
and the rdev mutex locked, fix that!

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211/mac80211: allow per-station GTKs

This adds API to allow adding per-station GTKs,
updates mac80211 to support it, and also allows
drivers to remove a key from hwaccel again when
this may be necessary due to multiple GTKs.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: avoid transmitting delBA to old AP

When roaming while we have active BA session,
we can end up transmitting delBA frames to
the old AP while we're already on the new AP's
channel, which can cause warnings.

Simply avoid sending those frames, but still
tear down the internal session state, since
they are not really necessary anyway as we
will implicitly disassociate when sending the
association to the new AP.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Introduce a wrapper for power save disable.

Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: remove unnecessary power save flags.

drv_config callback is called only after the ack for the nullframe
is received and so driver need not do anything special for this.

So remove NULLFUNC_COMPLETED, PS_ENABLED flags and bf_isnullfunc
flags from ath9k as mac80211 already handles them properly.

Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: merge ath9k_hw_ani_monitor_old and ath9k_hw_ani_monitor_new

After the last rounds of cleanup, these functions are now functionally
equivalent and can thus be merged.
Also get rid of some excessive (and redundant) debug messages.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: remove function pointer abstraction for internal ANI ops

The code gets more concise and readable when making the new ANI functions
fall back to the old ones if ANI v2 is disabled. This also makes further code
cleanup easier.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: remove code duplication in phy error counter handling

Split out the PHY error counter update from ath9k_hw_ani_monitor_*, reuse
it in ath9k_hw_proc_mib_event (merged from ath9k_hw_proc_mib_event_old
and ath9k_hw_proc_mib_event_new).

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: clean up ANI state handling

ANI state is kept per channel, so instead of keeping an array of ANI states
with an arbitrary size of 255, move the ANI state into the channel struct.

Move some config settings that are not per-channel out of
the per-channel struct to save some memory.

With those changes, ath9k_ani_restart_old and ath9k_ani_restart_new can
be merged into a single function.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: add a helper function to check for the new ANI implementation

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: clean up register write buffering

Throughout the code, DISABLE_REGWRITE_BUFFER is always called right after
REGWRITE_BUFFER_FLUSH. Since that's unlikely to change any time soon, that
makes keeping those ops separate rather pointless, as it only increases
code size and line number counts.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'upstream' of git://git.linux-mips.org/upstream-linus

* 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus:
  MIPS: Octeon: Place cnmips_cu2_setup in __init memory.
  MIPS: Don't place cu2 notifiers in __cpuinitdata
  MIPS: Calculate VMLINUZ_LOAD_ADDRESS based on the length of vmlinux.bin
  MIPS: Alchemy: Resolve prom section mismatches
  MIPS: Fix syscall 64 bit number comments.
  MIPS: Hookup fanotify_init, fanotify_mark, and prlimit64 syscalls.
  MIPS: TX49xx: Rename ARCH_KMALLOC_MINALIGN to ARCH_DMA_MINALIGN
  MIPS: N32: Fix getdents64 syscall for n32
  MIPS: Remove pr_<level> uses of KERN_<level>
  MIPS: PNX8550: Sort out machine halt, restart and powerdown functions.
  MIPS: GIC: Remove dependencies from Malta files.
  MIPS: Kconfig: Fix and clarify kconfig help text for VSMP and SMTC.
  MIPS: DMA: Fix computation of DMA flags from device's coherent_dma_mask.
  MIPS: Audit: Fix hang in entry.S.
  MIPS: Document why RELOC_HIDE is there.
  MIPS: Octeon: Determine if helper needs to be built
  MIPS: Use generic atomic64 for 32-bit kernels
  MIPS: RM7000: Symbol should be static
  MIPS: kspd: Adjust confusing if indentation
  MIPS: Fix a typo.

ath9k_hw: merge codepaths that access the cycle counter registers

The cycle counters are used by ANI to determine the amount of time that the
radio spent not receiving or transmitting. They're also used for debugging
purposes if the baseband watchdog on AR9003 detects a lockup.
In the future, we want to use these counters to determine the medium utilization
and export this information via survey. For that, we need to make sure that
the counter is only accessed from one place, which also ensures that
wraparounds won't occur at inconvenient points in time.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: clean up calibration flags

The calibration actual calibration flags are only used by the per chip family
source files, so it makes more sense to define them in those files instead
of globally. That way the code has to test for less flags.

Also instead of using a separate callback for testing whether a particular
calibration type is supported, simply adjust ah->supp_cals in the calibration
init which is called right after the hardware reset, before any of the
calibrations are run.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-2.6

Merge branch 'vhost-net-next' of git://git./linux/kernel/git/mst/vhost

mac80211: delete AddBA response timer

We never delete the addBA response timer, which
is typically fine, but if the station it belongs
to is deleted very quickly after starting the BA
session, before the peer had a chance to reply,
the timer may fire after the station struct has
been freed already. Therefore, we need to delete
the timer in a suitable spot -- best when the
session is being stopped (which will happen even
then) in which case the delete will be a no-op
most of the time.

I've reproduced the scenario and tested the fix.

This fixes the crash reported at
http://mid.gmane.org/4CAB6F96.6090701@candelatech.com

Cc: stable@kernel.org
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: fix regression in ANI listen time calculation

  wireless-testing
  commit 37e5bf6535a4d697fb9fa6f268a8354a612cbc00
  Author: Luis R. Rodriguez <lrodriguez@atheros.com>
  Date:   Sat Jun 12 00:33:40 2010 -0400

    ath9k_hw: fix clock rate calculations for ANI

This commit accidentally broke clock rate calculation by doubling the
calculated clock rate

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'for-linus' of git://git.kernel.dk/linux-2.6-block

* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
  writeback: always use sb->s_bdi for writeback purposes

Merge branch 'v2.6.36-rc6-urgent-fixes' of git://xenbits.xen.org/people/sstabellini/linux-pvhvm

* 'v2.6.36-rc6-urgent-fixes' of git://xenbits.xen.org/people/sstabellini/linux-pvhvm:
  xen: do not initialize PV timers on HVM if !xen_have_vector_callback
  xen: do not set xenstored_ready before xenbus_probe on hvm

Merge branch 'for-linus' of git://git./linux/kernel/git/mszeredi/fuse

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
  fuse: Initialize total_len in fuse_retrieve()

iwlagn: define 130 series of WiFi/BT combo devices

add new structures and defines need to identify 130 devices.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlagn: rename iwl5000_tx_resp

iwl5000_tx_resp really should be iwlagn_tx_resp, rename it.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: remove uncorrect comments

some structure belong to _agn devices, not just 5000. Fix it.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlagn: rename iwl5000_tx_power_dbm_cmd

iwl5000_tx_power_dbm_cmd really should be iwlagn_tx_power_dbm_cmd,
so rename it.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlagn: reduce redundant parameter definitions

move paramater definitions to a device paramater structure only
leaving the device name, which antennas are used and what firmware
file to use in the iwl_cfg structure.  this will not completely
remove the redundancies but greatly reduce them for devices that
only vary by name or antennas.  the parameters that are more
likely to change within a given device family are left in iwl_cfg.
also separate bt param structure added to help reduce more.

Signed-off-by: Jay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: schedule to deprecate software scan support

Hardware scan is the prefer method for all iwlwifi devices;
especially for dual-mode functions. Schedule to deprecate the
software scan support in kernel 2.6.40

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

bna: scope and dead code cleanup

As suggested by Stephen Hemminger:
1) Made functions and data structures static wherever possible.
2) Removed unused code.

Signed-off-by: Debashis Dutt <ddutt@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bna: fix interrupt handling

This fix handles the case when IRQ handler is called (for shared IRQs)
even before the driver is ready to handle interrupts.

Signed-off-by: Debashis Dutt <ddutt@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

fib: RCU conversion of fib_lookup()

fib_lookup() converted to be called in RCU protected context, no
reference taken and released on a contended cache line (fib_clntref)

fib_table_lookup() and fib_semantic_match() get an additional parameter.

struct fib_info gets an rcu_head field, and is freed after an rcu grace
period.

Stress test :
(Sending 160.000.000 UDP frames on same neighbour,
IP route cache disabled, dual E5540 @2.53GHz,
32bit kernel, FIB_HASH) (about same results for FIB_TRIE)

Before patch :

real 1m31.199s
user 0m13.761s
sys 23m24.780s

After patch:

real 1m5.375s
user 0m14.997s
sys 15m50.115s

Before patch Profile :

13044.00 15.4% __ip_route_output_key vmlinux
 8438.00 10.0% dst_destroy           vmlinux
 5983.00  7.1% fib_semantic_match    vmlinux
 5410.00  6.4% fib_rules_lookup      vmlinux
 4803.00  5.7% neigh_lookup          vmlinux
 4420.00  5.2% _raw_spin_lock        vmlinux
 3883.00  4.6% rt_set_nexthop        vmlinux
 3261.00  3.9% _raw_read_lock        vmlinux
 2794.00  3.3% fib_table_lookup      vmlinux
 2374.00  2.8% neigh_resolve_output  vmlinux
 2153.00  2.5% dst_alloc             vmlinux
 1502.00  1.8% _raw_read_lock_bh     vmlinux
 1484.00  1.8% kmem_cache_alloc      vmlinux
 1407.00  1.7% eth_header            vmlinux
 1406.00  1.7% ipv4_dst_destroy      vmlinux
 1298.00  1.5% __copy_from_user_ll   vmlinux
 1174.00  1.4% dev_queue_xmit        vmlinux
 1000.00  1.2% ip_output             vmlinux

After patch Profile :

13712.00 15.8% dst_destroy             vmlinux
 8548.00  9.9% __ip_route_output_key   vmlinux
 7017.00  8.1% neigh_lookup            vmlinux
 4554.00  5.3% fib_semantic_match      vmlinux
 4067.00  4.7% _raw_read_lock          vmlinux
 3491.00  4.0% dst_alloc               vmlinux
 3186.00  3.7% neigh_resolve_output    vmlinux
 3103.00  3.6% fib_table_lookup        vmlinux
 2098.00  2.4% _raw_read_lock_bh       vmlinux
 2081.00  2.4% kmem_cache_alloc        vmlinux
 2013.00  2.3% _raw_spin_lock          vmlinux
 1763.00  2.0% __copy_from_user_ll     vmlinux
 1763.00  2.0% ip_output               vmlinux
 1761.00  2.0% ipv4_dst_destroy        vmlinux
 1631.00  1.9% eth_header              vmlinux
 1440.00  1.7% _raw_read_unlock_bh     vmlinux

Reference results, if IP route cache is enabled :

real 0m29.718s
user 0m10.845s
sys 7m37.341s

25213.00 29.5% __ip_route_output_key   vmlinux
 9011.00 10.5% dst_release             vmlinux
 4817.00  5.6% ip_push_pending_frames  vmlinux
 4232.00  5.0% ip_finish_output        vmlinux
 3940.00  4.6% udp_sendmsg             vmlinux
 3730.00  4.4% __copy_from_user_ll     vmlinux
 3716.00  4.4% ip_route_output_flow    vmlinux
 2451.00  2.9% __xfrm_lookup           vmlinux
 2221.00  2.6% ip_append_data          vmlinux
 1718.00  2.0% _raw_spin_lock_bh       vmlinux
 1655.00  1.9% __alloc_skb             vmlinux
 1572.00  1.8% sock_wfree              vmlinux
 1345.00  1.6% kfree                   vmlinux

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

caif: fix two caif_connect() bugs

caif_connect() might dereference a netdevice after dev_put() it.

It also doesnt check dev_get_by_index() return value and could
dereference a NULL pointer.

Fix it, using RCU to avoid taking a reference.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Sjur Braendeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bonding: add retransmit membership reports tunable

Allow sysadmins to configure the number of multicast
membership report sent on a link failure event.

Signed-off-by: Flavio Leitner <fleitner@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bonding: fix to rejoin multicast groups immediately

The IGMP specs states that if the system receives a
membership report, it shouldn't send another for the
next minute. However, if a link failure happens right
after that, the backup slave and the switch connected
to this slave will not know about the multicast and
the traffic will hang for about a minute.

This patch fixes it to rejoin multicast groups immediately
after a failover restoring the multicast traffic.

Signed-off-by: Flavio Leitner <fleitner@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>