ASoC: wm_adsp: Expose mixer control API

Expose mixer control API for reading and writing controls from the kernel.
This API can be used by ALSA kernel drivers with ADSP support to
read and write firmware-defined memory regions.

Signed-off-by: Li Xu <li.xu@cirrus.com>
Signed-off-by: David Rhodes <david.rhodes@cirrus.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/1573847653-17094-2-git-send-email-david.rhodes@cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: tlv320aic31xx: configure output common-mode voltage

The tlv320aic31xx devices allow to adjust the output common-mode voltage
for best analog performance. The datasheet states that the common mode
voltage should be set to be <= AVDD/2.

This changes allows to configure the output common-mode voltage via a DT
property. If the property is absent the voltage is automatically chosen
as the highest voltage below/equal to AVDD/2.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Link: https://lore.kernel.org/r/20191118151207.28576-1-l.stach@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: SOF: Intel: Fix CFL and CML FW nocodec binary names.

The manifest information is different between CNL, CML and CFL platforms
hence we need to load different files.

Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191111222901.19892-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: pcm3168a: Add support for optional RST gpio handling

In case the RST line is connected to a GPIO line it needs to be pulled high
when the driver probes to be able to use the codec.

Add support also for cases when more than one codec is is controlled by the
same GPIO line by requesting the gpio with GPIOD_FLAGS_BIT_NONEXCLUSIVE.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191113124734.27984-3-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: pcm3168a: Document optional RST gpio

On boards where the RST line is not pulled up, but it is connected to a
GPIO line this property must present in order to be able to enable the
codec.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191113124734.27984-2-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: wm5100: add missed pm_runtime_disable

The driver forgets to call pm_runtime_disable in remove and
probe failure.
Add the calls to fix it.

Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20191118073707.28298-1-hslester96@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: wm2200: add missed operations in remove and probe failure

This driver misses calls to pm_runtime_disable and regulator_bulk_disable
in remove and a call to free_irq in probe failure.
Add the calls to fix it.

Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Link: https://lore.kernel.org/r/20191118073633.28237-1-hslester96@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: qcom: q6asm-dai: add support to flac decoder

Qualcomm DSPs also support the flac decoder, so add support for FLAC
decoder and convert the snd_dec_flac params to qdsp format.

Co-developed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20191115102705.649976-4-vkoul@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: qcom: q6asm: add support to flac config

Qualcomm DSPs expect flac config to be set for flac decoders, so add the
API to program the flac config to the DSP

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20191115102705.649976-3-vkoul@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>

ALSA: compress: add flac decoder params

The current design of sending codec parameters assumes that decoders
will have parsers so they can parse the encoded stream for parameters
and configure the decoder.

But this assumption may not be universally true and we know some DSPs
which do not contain the parsers so additional parameters are required
to be passed.

So add these parameters starting with FLAC decoder. The size of
snd_codec_options is still 120 bytes after this change (due to this
being a union)

Co-developed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20191115102705.649976-2-vkoul@kernel.org
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: rt5677: rt5677_check_hotword() can be static

Fixes: 21c00e5df439 ("ASoC: rt5677: Enable jack detect while DSP is running")
Signed-off-by: kbuild test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20191114153304.n4pyix7qadu76tx4@4978f4969bb8
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: ti: davinci-mcasp: Use dma_request_chan() directly for channel request

dma_request_slave_channel_reason() is:
#define dma_request_slave_channel_reason(dev, name) \
dma_request_chan(dev, name)

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191113095445.3211-3-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: dmaengine: Use dma_request_chan() directly for channel request

dma_request_slave_channel_reason() is:
#define dma_request_slave_channel_reason(dev, name) \
dma_request_chan(dev, name)

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191113095445.3211-2-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: soc-core: care card_probed at soc_cleanup_card_resources()

soc_cleanup_card_resources() will call card->remove(), but it should be
called if card->probe() or card->late_probe() are called.
snd_soc_bind_card() might be error before calling
card->probe() / card->late_probe().
In that time, card->remove() will be called.
This patch adds card_probed parameter to judge it.

Fixes: bfce78a559655 ("ASoC: soc-core: tidyup soc_init_dai_link()")
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/87o8xg4ltr.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: soc-core: move snd_soc_unbind_card() next to snd_soc_bind_card()

To makes code readable, this patch moves snd_soc_unbind_card() next
to snd_soc_bind_card().

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87pnhw4lu5.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: soc-core: call snd_soc_dapm_shutdown() at soc_cleanup_card_resources()

It is easy to read code if it is cleanly using paired function/naming,
like start <-> stop, register <-> unregister, etc, etc.
But, current ALSA SoC code is very random, unbalance, not paired, etc.
It is easy to create bug at the such code, and it will be difficult to
debug.

snd_soc_bind_card() is calling snd_soc_dapm_init() for both
card and component.
Let's call paired snd_soc_dapm_shutdown() at paired
soc_cleanup_card_resources().

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87r22c4lub.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: tas2770: clean up an indentation issue

There is a block that is indented too deeply, remove
the extraneous tabs.

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20191112190218.282337-1-colin.king@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>

dt-bindings: vendor-prefixes: Add 'fsi[ab]' to the list of non-vendor prefixes

'fsia' and 'fsib' property prefixes were added as schema in commit
2f52475bac7e ("ASoC: fsi: switch to yaml base Documentation").
Unfortunately to do checks on actual vendor prefixes, we have to track
the handful of prefixes which are not vendors like 'fsia' and 'fsib'.

Fixes: 2f52475bac7e ASoC: fsi: switch to yaml base Documentation
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20191108153538.11970-1-robh@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: soc-core: tidyup soc_probe_aux_devices()

snd_soc_bind_card() is calling many initialize functions
for each card / link / dai / aux etc, etc, etc...
When error happen, the message is indicated at snd_soc_bind_card(),
not at each functions.
But, only soc_probe_aux_devices() case is indicating error at functions,
not at snd_soc_bind_card().
It is not an issue, but unbalanced.

This patch moves error message to snd_soc_bind_card().
Also avoids deep-nested code.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87lfsthkw9.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: soc-core: merge snd_soc_bind_card() and snd_soc_instantiate_card()

having both soc_bind_card() and snd_soc_instantiate_card() is
very confusable. Let's merge these.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87mud9hkwj.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: soc-core: merge soc_remove_component() and soc_cleanup_component()

having both soc_remove_component() and soc_cleanup_component() is
very confusable. Let's merge these.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87o8xphkwt.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: soc-core: merge snd_soc_remove_dai_link() and soc_unbind_dai_link()

We don't need to separete snd_soc_remove_dai_link() and
soc_unbind_dai_link() anymore. Let's merge these.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87pni5hkx1.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: soc-core: merge snd_soc_add_dai_link() and soc_bind_dai_link()

We don't need to separete snd_soc_add_dai_link() and
soc_bind_dai_link() anymore. Let's merge these.

One note is that before this patch, it adds list (A)
eventhough if it had dai_link->ignore (1), or already bounded dai_link (2).
But I guess it is wrong. This patch also solve this issue.

/* BEFORE */
int soc_bind_dai_link(...)
{
...
(1) if (dai_link->ignore)
return 0;

(2) if (soc_is_dai_link_bound(...))
return 0;
...
}

int snd_soc_add_dai_link(...)
{
...
=> ret = soc_bind_dai_link(...);
=> if (ret < 0)
=> return ret;

(A) list_add_tail(&dai_link->list, &card->dai_link_list);
...
}

/* AFTER */

int snd_soc_add_dai_link(...)
{
...
(1) if (dai_link->ignore)
return 0;

(2) if (soc_is_dai_link_bound(...))
return 0;
...
(A) list_add_tail(&dai_link->list, &card->dai_link_list);
return 0;
}

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87r22lhkx8.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: soc-core: merge snd_soc_unregister_dai() and soc_del_dai()

We don't need to separete snd_soc_unregister_dai() and
soc_del_dai() anymore. Let's merge these

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87sgn1hkxg.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: soc-core: merge snd_soc_register_dai() and soc_add_dai()

We don't need to separete snd_soc_register_dai() and
soc_add_dai() anymore. Let's merge these

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87tv7hhkxm.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: soc-core: remove soc_is_dai_link_bound()

Because complex separeted "card pre-listed component" and
"topology added component" duplicated operation is now
becoming simple, we don't need to check already bound dai_link
which is not exist anymore.
This patch removes soc_is_dai_link_bound().

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87v9rxhkxw.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: SOF: topology: free kcontrol memory on error

The volume and bytes kcontrols are currently not freeing their
memory on initialization failures. When an error occurs, all the
widgets loaded so far are unloaded via sof_widget_unload().
But this only happens for the widgets that got successfully loaded.

Fix that by kfree()-ing the allocated memory on load error.

Fixes: 311ce4fe7637d ("ASoC: SOF: Add support for loading topologies")
Reviewed-by: Paul Olaru <paul.olaru@nxp.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Dragos Tarcatu <dragos_tarcatu@mentor.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191111222039.19651-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: SOF: PM: only suspend to D0I3 when needed

We should suspend audio to D3 by default, for the sake of power saving,
change the condition of D0I3 suspending here to that when there is
stream with suspend_ignored specified.

Signed-off-by: Keyon Jie <yang.jie@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191111223343.19986-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: SOF: add helper to check if we should enter d0i3 suspend

Add helper to check if the DSP should be put in D0i3. This function
returns true if a stream has ignored the SUSPEND trigger to keep the
pipelines running in the DSP.

Signed-off-by: Keyon Jie <yang.jie@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191111223343.19986-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: SOF: PM: add check before setting d0_substate

Add check before seeting d0_substate and return success if Audio DSP is
already in the target substate.

Signed-off-by: Keyon Jie <yang.jie@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191111223343.19986-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: SOF: PM: add state machine to comments

Add Audio DSP state machine with comments. Note that the
'D0<-->runtime D0I3' part is not implemented yet.

Signed-off-by: Keyon Jie <yang.jie@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191111223343.19986-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: SOF: Intel: hda: use fallback for firmware name

We have platforms such as CFL with no known I2S codec being used, and
the ACPI tables are currently empty, so fall-back to using the
firmware filename used in nocodec mode

Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191111222901.19892-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: Intel: acpi-match: split CNL tables in three

Due to firmware manifest/signature differences, we have to use
different firmware names, so split CNL machine table in three (CNL,
CFL, CML).

The CFL table is currently empty since all known platforms use
HDaudio, but let's plan ahead.

Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191111222901.19892-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: wm8904: configure sysclk/FLL automatically

This adds a new mode WM8904_CLK_AUTO which automatically enables the FLL
if a frequency different than the MCLK is set.

These additions make the codec work with the simple-card driver in
general and especially in systems where the MCLK doesn't match the
required clock.

Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20191108203152.19098-1-michael@walle.cc
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: Intel: kbl_rt5663_rt5514_max98927: Add dmic format constraint

On KBL platform, the microphone is attached to external codec(rt5514)
instead of PCH. However, TDM slot between PCH and codec is 16 bits only.
In order to avoid setting wrong format, we should add a constraint to
force to use 16 bits format forever.

Signed-off-by: Yu-Hsuan Hsu <yuhsuan@chromium.org>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190923162940.199580-1-yuhsuan@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: Add DA7213 audio codec as selectable option

This commit adds the Dialog DA7213 audio codec as a selectable option
in the kernel config. Currently the driver can only be selected for
Intel Baytrail/Cherrytrail devices or if SND_SOC_ALL_CODECS is enabled.

Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20191108174843.11227-3-sebastian.reichel@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: rt5677: Wait for DSP to boot before loading firmware

Wait for hardware to startup. If we load before hardware is ready we
could end up corrupting the firmware.

Signed-off-by: Curtis Malainey <cujomalainey@chromium.org>
Link: https://lore.kernel.org/r/20191106011335.223061-12-cujomalainey@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: rt5677: Set ADC clock to use PLL and enable ASRC

Use the PLL to kept the correct 24M clock rate so frequency shift does
not occur when using the DSP VAD.

Signed-off-by: Curtis Malainey <cujomalainey@chromium.org>
Link: https://lore.kernel.org/r/20191106011335.223061-11-cujomalainey@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: bdw-rt5677: Turn on MCLK1 for DSP via DAPM

The RT5677 DSP needs the I2S MCLK1 to run its DSP. Add a dapm route to
SSP0 CODEC IN so the clock is turned on automatically when the DSP is
turned on.

Signed-off-by: Curtis Malainey <cujomalainey@chromium.org>
Link: https://lore.kernel.org/r/20191106011335.223061-10-cujomalainey@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: rt5677: Allow VAD to be shut on/off at all times

Due to limitations of the clocking configuration, we have no way of
scheduling our hibernation before the bdw dsp hibernates. This causes
issues when the system suspends with an open stream. We need userspace
to toggle the kcontrol before we are suspended so that any writes on
suspend are not lost and we don't corrupt the regmap.

Signed-off-by: Curtis Malainey <cujomalainey@chromium.org>
Link: https://lore.kernel.org/r/20191106011335.223061-9-cujomalainey@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: rt5677: Disable irq at suspend

The irq is disabled at suspend to avoid running the threaded irq
handler after the codec has been powered off. At resume, codec irq is
re-enabled and the interrupt status register is checked to see if
headphone has been pluggnd/unplugged while the device is suspended.

There is still a chance that the headphone gets enabled or disabled
after the codec is suspended. disable_irq syncs the threaded irq
handler, but soc-jack's threaded irq handler schedules a delayed
work to poll gpios (for debounce). This is still OK. The codec won't
be powered back on again because all audio paths have been suspended,
and there are no force enabled supply widgets (MICBIAS1 is disabled).
The gpio status read after codec power off could be wrong, so the
gpio values are checked again after resume.

Signed-off-by: Ben Zhang <benzh@chromium.org>
Signed-off-by: Curtis Malainey <cujomalainey@chromium.org>
Link: https://lore.kernel.org/r/20191106011335.223061-8-cujomalainey@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: rt5677: Stop and restart DSP over suspend/resume

MCLK1 gets disabled at suspend and re-enabled at resume. Before
MCLK1 is re-enabled, if the DSP is already on (either the DSP was
left on during suspend, or the DSP is turned on early at resume),
i2c register read returns garbage and corrupts the regmap cache.

This patch stops the DSP before suspend and restarts it after
resume with a dalay to ensure MCLK is on while loading firmware.

Signed-off-by: Ben Zhang <benzh@chromium.org>
Signed-off-by: Curtis Malainey <cujomalainey@chromium.org>
Link: https://lore.kernel.org/r/20191106011335.223061-7-cujomalainey@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: rt5677: Mark reg RT5677_PWR_ANLG2 as volatile

The codec dies when RT5677_PWR_ANLG2(MX-64h) is set to 0xACE1
while it's streaming audio over SPI. The DSP firmware turns
on PLL2 (MX-64 bit 8) when SPI streaming starts.  However regmap
does not believe that register can change by itself. When
BST1 (bit 15) is turned on with regmap_update_bits(), it doesn't
read the register first before write, so PLL2 power bit is
cleared by accident.

Marking MX-64h as volatile in regmap solved the issue.

Signed-off-by: Ben Zhang <benzh@chromium.org>
Signed-off-by: Curtis Malainey <cujomalainey@chromium.org>
Link: https://lore.kernel.org/r/20191106011335.223061-6-cujomalainey@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: rt5677: Add DAPM audio path for hotword stream

Add a DAPM audio path from "DMIC L1" to "DSP Buffer" so that
when hotwording is enabled, DAPM does not power off the codec
with SND_SOC_BIAS_OFF.

Signed-off-by: Ben Zhang <benzh@chromium.org>
Signed-off-by: Curtis Malainey <cujomalainey@chromium.org>
Link: https://lore.kernel.org/r/20191106011335.223061-5-cujomalainey@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: rt5677: Enable jack detect while DSP is running

Before a hotword is detected, GPIO1 pin is configured as IRQ
output so that jack detect works. When a hotword is detected,
the DSP firmware configures the GPIO1 pin as GPIO1 and
drives a 1. rt5677_irq() is called after a rising edge on
the GPIO1 pin, due to either jack detect event or hotword
event, or both. All possible events are checked and handled
in rt5677_irq() where GPIO1 pin is configured back to IRQ
output if a hotword is detected.

Signed-off-by: Ben Zhang <benzh@chromium.org>
Signed-off-by: Curtis Malainey <cujomalainey@chromium.org>
Link: https://lore.kernel.org/r/20191106011335.223061-4-cujomalainey@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: bdw-rt5677: Add a DAI link for rt5677 SPI PCM device

This link is needed for the RT5677 DSP to do hotwording

Signed-off-by: Ben Zhang <benzh@chromium.org>
Signed-off-by: Curtis Malainey <cujomalainey@chromium.org>
Link: https://lore.kernel.org/r/20191106011335.223061-3-cujomalainey@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: rt5677: Load firmware via SPI using delayed work

The firmware rt5677_elf_vad is an ELF binary obtained from
request_firmware(). Sections of the ELF are loaded to
the DSP via SPI. A model (e.g. en_us.mmap) can optionally be
loaded to the DSP at RT5677_MODEL_ADDR to overwrite the
baked-in model in rt5677_elf_vad.

Then we switch to DSP mode, load firmware, and let DSP run.
When a hotword is detected, an interrupt is fired and
rt5677_irq() is called. When 'DSP VAD Switch' is turned off,
the codec is set back to normal mode.

The kcontrol 'DSP VAD Switch' is automatically enabled/disabled
when the hotwording PCM stream is opened/closed.

Signed-off-by: Ben Zhang <benzh@chromium.org>
Signed-off-by: Curtis Malainey <cujomalainey@chromium.org>
Link: https://lore.kernel.org/r/20191106011335.223061-2-cujomalainey@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: fsl_audmix: Add spin lock to protect tdms

Audmix support two substream, When two substream start
to run, the trigger function may be called by two substream
in same time, that the priv->tdms may be updated wrongly.

The expected priv->tdms is 0x3, but sometimes the
result is 0x2, or 0x1.

Fixes: be1df61cf06e ("ASoC: fsl: Add Audio Mixer CPU DAI driver")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/1e706afe53fdd1fbbbc79277c48a98f8416ba873.1573458378.git.shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>

ASoC: SOF: Intel: hda: set L1SEN on S0ix suspend

Set L1SEN to make sure the system can enter S0ix, and restore it on
resume.

Signed-off-by: Keyon Jie <yang.jie@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191101170916.26517-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: SOF: topology: fix missing NULL pointer check

Add check to avoid possible NULL pointer dereference issue.

This issue was reported by static analysis tools, we didn't face this
issue but we can't rule it out either as a false positive.

Reported-by: Keqiao Zhang <keqiao.zhang@intel.com>
Signed-off-by: Keyon Jie <yang.jie@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191101170916.26517-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: core: Fix compile warning with CONFIG_DEBUG_FS=n

Paper over a compile warning:
  sound/soc/soc-pcm.c:1185:8: warning: unused variable ‘name’

Fixes: 0632fa042541 ("ASoC: core: Fix pcm code debugfs error")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20191107134833.1502-1-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: fsi: switch to yaml base Documentation

This patch switches from .txt base to .yaml base Document for FSI.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/878sp4jaqy.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: SOF: topology: Fix bytes control size checks

When using the example SOF amp widget topology, KASAN dumps this
when the AMP bytes kcontrol gets loaded:

[ 9.579548] BUG: KASAN: slab-out-of-bounds in
sof_control_load+0x8cc/0xac0 [snd_sof]
[ 9.588194] Write of size 40 at addr ffff8882314559dc by task
systemd-udevd/2411

Fix that by rejecting the topology if the bytes data size > max_size

Fixes: 311ce4fe7637d ("ASoC: SOF: Add support for loading topologies")
Reviewed-by: Jaska Uimonen <jaska.uimonen@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Dragos Tarcatu <dragos_tarcatu@mentor.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191106145816.9367-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

Merge branch 'for-5.4' of https://git./linux/kernel/git/broonie/sound into asoc-5.5

ASoC: soc-core: fixup dead-lock at snd_soc_unregister_component()

snd_soc_unregister_component() is calling snd_soc_lookup_component()
under mutex_lock(). But, snd_soc_lookup_component() itself is using
mutex_lock(), thus it will be dead-lock.
This patch adds _nolocked version of it, and avoid dead-lock issue.

Fixes: ac6a4dd3e9f0("ASoC: soc-core: use snd_soc_lookup_component() at snd_soc_unregister_component()")
Reported-by: "kernelci.org bot" <bot@kernelci.org>"
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87bltph4da.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: soc-core: fix RIP warning on card removal

SOF module load/unload tests show nasty recurring warnings:

WARNING: CPU: 5 PID: 1339 at sound/core/control.c:466
snd_ctl_remove+0xf0/0x100 [snd]
RIP: 0010:snd_ctl_remove+0xf0/0x100 [snd]

This regression was introduced by the removal of the call to
soc_remove_link_components() before soc_card_free() is invoked.

Go back to the initial order but only call
soc_remove_link_components() once.

Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Fixes: 5a4c9f054ceea ("ASoC: soc-core: snd_soc_unbind_card() cleanup")
GitHub issue: https://github.com/thesofproject/linux/issues/1424
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191106145801.9316-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: SOF: topology: Fix bytes control size checks

When using the example SOF amp widget topology, KASAN dumps this
when the AMP bytes kcontrol gets loaded:

[ 9.579548] BUG: KASAN: slab-out-of-bounds in
sof_control_load+0x8cc/0xac0 [snd_sof]
[ 9.588194] Write of size 40 at addr ffff8882314559dc by task
systemd-udevd/2411

Fix that by rejecting the topology if the bytes data size > max_size

Fixes: 311ce4fe7637d ("ASoC: SOF: Add support for loading topologies")
Reviewed-by: Jaska Uimonen <jaska.uimonen@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Dragos Tarcatu <dragos_tarcatu@mentor.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191106145816.9367-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: soc.h: dobj is used only when SND_SOC_TOPOLOGY

snd_soc_dobj is used only when SND_SOC_TOPOLOGY was selected.
Let's enable it under SND_SOC_TOPOLOGY.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/87o8xq251d.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: soc-core: remove topology specific operation

soc-core has some API which is used from topology, but it is doing
topology specific operation at soc-core.
soc-core should care about core things, and topology should care
about topology things, otherwise, it is very confusable.

For example topology type is not related to soc-core,
it is topology side issue.

This patch removes meaningless check from soc-core.

This patch keeps extra initialization/destruction at
snd_soc_add_dai_link() / snd_soc_remove_dai_link()
which were for topology.
From this patch, non-topology card can use it.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/87pni6251h.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: soc-core: call snd_soc_register_dai() from snd_soc_register_dais()

ALSA SoC has 2 functions.
snd_soc_register_dai()  is used from topology
snd_soc_register_dais() is used from snd_soc_add_component()

In general, people think like _dai() is called from _dais()
with for loop. But in reality, these are very similar
but different implementation.
We shouldn't have duplicated and confusing implementation.

This patch calls snd_soc_register_dai() from snd_soc_register_dais()

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/87r22m251l.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: soc-core: don't call snd_soc_dapm_new_dai_widgets() at snd_soc_register_dai()

ALSA SoC has 2 functions.
snd_soc_register_dai()  is used from topology
snd_soc_register_dais() is used from snd_soc_add_component()

In general, people think like _dai() is called from _dais()
with for loop. But in reality, these are very similar
but different implementation.
We shouldn't have duplicated and confusing implementation.

snd_soc_register_dai() is now used from topology.
But to reduce duplicated code, it should be used from _dais(), too.

Because of topology side specific reason,
it is calling snd_soc_dapm_new_dai_widgets(),
but it is not needed _dais() side.

This patch factorizes snd_soc_register_dai() to
topology / _dais() common part, and topology specific part.
And do topology specific part at soc-topology.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/87sgn2251p.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: soc-core: have legacy_dai_naming at snd_soc_register_dai()

ALSA SoC has 2 functions.
snd_soc_register_dai()  is used from topology
snd_soc_register_dais() is used from snd_soc_add_component()

In general, people think like _dai() is called from _dais()
with for loop. But in reality, these are very similar
but different implementation.
We shouldn't have duplicated and confusing implementation.

snd_soc_register_dai() is now used from topology.
But to reduce duplicated code, it should be used from _dais(), too.
To prepare it, this patch adds missing parameter legacy_dai_naming
to snd_soc_register_dai().

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/87tv7i251u.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: soc-core: add snd_soc_unregister_dai()

It is easy to read code if it is cleanly using paired function/naming,
like start <-> stop, register <-> unregister, etc, etc.
But, current ALSA SoC code is very random, unbalance, not paired, etc.
It is easy to create bug at the such code, and is difficult to debug.

This patch adds missing soc_del_dai() and snd_soc_unregister_dai().

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/87v9ry251z.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: soc-core: move snd_soc_unregister_dais()

This patch moves snd_soc_unregister_dais() next to
snd_soc_register_dais().
This is prepare for snd_soc_register_dais() cleanup

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/87woce2524.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: soc-core: move snd_soc_register_dai()

This patch moves snd_soc_register_dai() next to
snd_soc_register_dais().
This is prepare for snd_soc_register_dais() cleanup.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/87y2wu2528.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: soc-core: use snd_soc_lookup_component() at snd_soc_unregister_component()

snd_soc_unregister_component() is now finding component manually,
but we already have snd_soc_lookup_component() to find component;
Let's use existing function.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/87zhha252c.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: soc-core: remove snd_soc_component_add/del()

soc-core has
snd_soc_add_component(), snd_soc_component_add(),
snd_soc_del_component(), snd_soc_component_del().

These are very confusing naming.
snd_soc_component_xxx() are called from snd_soc_xxx_component(),
and these are very small.
Let's merge these into snd_soc_xxx_component(), and
remove snd_soc_component_xxx().

Reported-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/871rum3jmy.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: soc-core: add snd_soc_del_component_unlocked()

It is easy to read code if it is cleanly using paired function/naming,
like start <-> stop, register <-> unregister, etc, etc.
But, current ALSA SoC code is very random, unbalance, not paired, etc.
It is easy to create bug at the such code, and is difficult to debug.

Now ALSA SoC has snd_soc_add_component(), but there is no paired
snd_soc_del_component(). Thus, snd_soc_unregister_component() is
calling cleanup function randomly. it is difficult to read.
This patch adds missing snd_soc_del_component_unlocked() and
balance up code.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/8736f23jn4.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: soc-core: tidyup snd_soc_lookup_component()

snd_soc_lookup_component() is using mix of continue and break
in the same loop. It is odd.
This patch cleanup it.

Reported-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/874kzi3jn8.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: soc-core: move snd_soc_lookup_component()

This patch moves snd_soc_lookup_component() to upper side.
This is prepare for snd_soc_unregister_component()

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/875zjy3jnd.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: soc-core: add soc_unbind_dai_link()

It is easy to read code if it is cleanly using paired function/naming,
like start <-> stop, register <-> unregister, etc, etc.
But, current ALSA SoC code is very random, unbalance, not paired, etc.
It is easy to create bug at the such code, and it will be difficult to
debug.

ALSA SoC has soc_bind_dai_link(), but its paired soc_unbind_dai_link()
is not implemented.
More confusable is that soc_remove_pcm_runtimes() which should be
soc_unbind_dai_link() is implemented without synchronised
to soc_bind_dai_link().

This patch cleanup this unbalance.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/877e4e3jni.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: soc-core: call soc_bind_dai_link() under snd_soc_add_dai_link()

If we focus to soc_bind_dai_link() at snd_soc_instantiate_card(),
we will notice very complex operation.

static int snd_soc_instantiate_card(...)
{
...
/*
 * (1) Bind dai_link via card pre-linked dai_link
 *
 * Bind dai_link via card pre-linked.
 * 1 dai_link will be 1 rtd, and connected to card.
 * for_each_card_prelinks() is for card pre-linked dai_link.
 *
 * Image
 *
 * card
 * - rtd(A)
 * - rtd(A)
 */
for_each_card_prelinks(card, i, dai_link) {
ret = soc_bind_dai_link(card, dai_link);
...
}
...
/*
 * (2) Connect card pre-linked dai_link to card list
 *
 * Connect all card pre-linked dai_link to *card list*.
 * Here, (A) means from card pre-linked.
 *
 * Image
 *
 * card card list
 *  - rtd(A)  - dai_link(A)
 *  - rtd(A)  - dai_link(A)
 *  - ...  - ...
 */
for_each_card_prelinks(card, i, dai_link) {
ret = snd_soc_add_dai_link(card, dai_link);
...
}
...
/*
 * (3) Probe binded component
 *
 * Each rtd has many components.
 * Here probes each rtd connected components.
 * rtd(A) in Image is the probe target.
 *
 * During this component probe, topology may add new dai_link to
 * *card list* by using snd_soc_add_dai_link() which is
 * used at (2).
 * Here, (B) means from topology
 *
 * Image
 *
 * card card list
 *  - rtd(A)  - dai_link(A)
 *  - rtd(A)  - dai_link(A)
 *  - ...  - ...
 *  - dai_link(B)
 *  - dai_link(B)
 */
ret = soc_probe_link_components(card);
...

/*
 * (4) Bind dai_link again
 *
 * Bind dai_link again for topology.
 * Note, (1) used for_each_card_prelinks(),
 * here is using  for_each_card_links()
 *
 * This means from card list.
 * As Image indicating, it has dai_link(A) (from card pre-link)
 * and dai_link(B) (from topology).
 * main target here is dai_link(B).
 * soc_bind_dai_link() ignores already used
 * dai_link (= dai_link(A))
 *
 * Image
 *
 * card card list
 *  - rtd(A)  - dai_link(A)
 *  - rtd(A)  - dai_link(A)
 *  - ...  - ...
 *  - rtd(B)  - dai_link(B)
 *  - rtd(B)  - dai_link(B)
 */
for_each_card_links(card, dai_link) {
ret = soc_bind_dai_link(card, dai_link);
...
}
...
}

As you see above, it is doing very complex method.
The problem is binding dai_link via "card pre-linked" (= (1)) and
"topology added dai_link" (= (3)) are separated.
The code can be simple if we can bind dai_link when dai_link
is connected to *card list*.
This patch do it.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/878sou3jnn.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: soc-core: remove duplicated soc_is_dai_link_bound()

soc_is_dai_link_bound() check will be called both
*before* soc_bind_dai_link() (A), and
*under*  soc_bind_dai_link() (B).
These are very verbose code. Let's remove one of them.

* static int soc_bind_dai_link(...)
{
...
(B) if (soc_is_dai_link_bound(...)) {
...
return 0;
}
...
}

static int snd_soc_instantiate_card(...)
{
...
for_each_card_links(...) {
(A) if (soc_is_dai_link_bound(...))
continue;

* ret = soc_bind_dai_link(...);
if (ret)
goto probe_end;
}
...
}

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/87a79a3jns.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: soc-core: typo fix at soc_dai_link_sanity_check()

Reported-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/87bltq3jo7.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: soc-core: tidyup soc_init_dai_link()

soc_init_dai_link() is needed to be called before soc_bind_dai_link().

int snd_soc_instantiate_card()
{
for_each_card_prelinks(...) {
(1) ret = soc_init_dai_link(...);
...
}
...
for_each_card_prelinks(...) {
(2) ret = soc_bind_dai_link(...);
...
}
...
for_each_card_links(...) {
...
(A) ret = soc_init_dai_link(...);
...
(B) ret = soc_bind_dai_link(...);
}
...

(1) is for (2), and (A) is for (B)
(1) and (2) are for card prelink   dai_link.
(A) and (B) are for topology added dai_link.

soc_init_dai_link() is sanity check for dai_link, not initializing today.
Therefore, it is confusable naming. We can rename it as sanity_check.

And this check is for soc_bind_dai_link().
It can be more simple code if we can call it from soc_bind_dai_link().

This patch renames it to soc_dai_link_sanity_check(), and
call it from soc_bind_dai_link().

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/87d0e63joh.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: soc-core: move soc_init_dai_link()

This patch moves soc_init_dai_link() next to soc_bind_dai_link().
This is prepare for soc_bind_dai_link() cleanup.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/87eeym3joq.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: adau7118: Fix example warning

The ADAU7118 has an example where the codec has an i2c address of 14, and
the unit address set to 14 as well.

However, while the address is expressed in decimal, the unit-address is
supposed to be in hexadecimal, which ends up with two different addresses
that trigger a DTC warning. Fix this by setting the address to 0x14.

Cc: Nuno Sá <nuno.sa@analog.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Fixes: 969d49b2cdc8 ("dt-bindings: asoc: Add ADAU7118 documentation")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20191105105615.21391-1-maxime@cerno.tech
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: SOF: topology: set trigger order for FE DAI link

Set trigger order for FE DAI links to SND_SOC_DPCM_TRIGGER_POST
to trigger the BE DAI's before the FE DAI's. This prevents the
xruns seen on playback pipelines using the link DMA.

Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191104224812.3393-3-ranjani.sridharan@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: pcm: update FE/BE trigger order based on the command

Currently, the trigger orders SND_SOC_DPCM_TRIGGER_PRE/POST
determine the order in which FE DAI and BE DAI are triggered.
In the case of SND_SOC_DPCM_TRIGGER_PRE, the FE DAI is
triggered before the BE DAI and in the case of
SND_SOC_DPCM_TRIGGER_POST, the BE DAI is triggered before
the FE DAI. And this order remains the same irrespective of the
trigger command.

In the case of the SOF driver, during playback, the FW
expects the BE DAI to be triggered before the FE DAI during
the START trigger. The BE DAI trigger handles the starting of
Link DMA and so it must be started before the FE DAI is started
to prevent xruns during pause/release. This can be addressed
by setting the trigger order for the FE dai link to
SND_SOC_DPCM_TRIGGER_POST. But during the STOP trigger,
the FW expects the FE DAI to be triggered before the BE DAI.
Retaining the same order during the START and STOP commands,
results in FW error as the DAI component in the FW is still
active.

The issue can be fixed by mirroring the trigger order of
FE and BE DAI's during the START and STOP trigger. So, with the
trigger order set to SND_SOC_DPCM_TRIGGER_PRE, the FE DAI will be
trigger first during SNDRV_PCM_TRIGGER_START/STOP/RESUME
and the BE DAI will be triggered first during the
STOP/SUSPEND/PAUSE commands. Conversely, with the trigger order
set to SND_SOC_DPCM_TRIGGER_POST, the BE DAI will be triggered
first during the SNDRV_PCM_TRIGGER_START/STOP/RESUME commands
and the FE DAI will be triggered first during the
SNDRV_PCM_TRIGGER_STOP/SUSPEND/PAUSE commands.

Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191104224812.3393-2-ranjani.sridharan@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: max98373: replace gpio_request with devm_gpio_request

Use devm_gpio_request() to automatic unroll when fails and avoid
resource leaks at error paths.

Signed-off-by: Yong Zhi <yong.zhi@intel.com>
Link: https://lore.kernel.org/r/1572905399-22402-1-git-send-email-yong.zhi@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: stm32: sai: add restriction on mmap support

Do not support mmap in S/PDIF mode. In S/PDIF mode
the buffer has to be copied, to allow the channel status
bits insertion.

Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Link: https://lore.kernel.org/r/20191104133654.28750-1-olivier.moysan@st.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: Intel: boards: sof_rt5682: use dependency on SOF_HDA_LINK

The wrong dependency is used and the build can be broken

Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191101173045.27099-12-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: Intel: boards: Geminilake is only supported by SOF

Geminilake machine drivers are only tested and recommended with SOF.

Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191101173045.27099-11-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: Intel: boards: fix configs for bxt-da7219-max98057a

The same driver is reused for 3 different configurations, but the
driver will only be build if ApolloLake is selected.

Fix and make sure each device can work without dependencies on others
(useful for minimal configurations).

Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191101173045.27099-10-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: Intel: boards: remove select SND_HDA_DSP_LOADER

This option is only required with the Skylake platform driver, there
is no reason to have this option in machine drivers. This is
e.g. useless for SOF-based solutions.

Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191101173045.27099-9-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: Intel: Skylake: mark HDAudio codec support as deprecated.

This option famously broke audio on Linus' laptop and the problem have
not been fixed.

Mark as DEPRECATED to avoid any ambiguity with distros.

Use SOF if you need HDaudio support w/ the DSP enabled, e.g. for DMIC
capture.

Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191101173045.27099-8-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: SOF: Intel: use def_tristate, avoid using select

So far we used select to use the relevant built-in/module options, but
this led to blurring layers between core and Intel Kconfigs.

Use def_tristate works just as well and removes Intel stuff from the code.

Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191101173045.27099-7-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: SOF: imx: fix reverse CONFIG_SND_SOC_SOF_OF dependency

updated solution to the problem reported with randconfig:

CONFIG_SND_SOC_SOF_IMX depends on CONFIG_SND_SOC_SOF, but is in
turn referenced by the sof-of-dev driver. This creates a reverse
dependency that manifests in a link error when CONFIG_SND_SOC_SOF_OF
is built-in but CONFIG_SND_SOC_SOF_IMX=m:

sound/soc/sof/sof-of-dev.o:(.data+0x118): undefined reference to `sof_imx8_ops'

use def_trisate to propagate the right settings without select.

Fixes: f4df4e4042b0 ("ASoC: SOF: imx8: Fix COMPILE_TEST error")
Fixes: 202acc565a1f ("ASoC: SOF: imx: Add i.MX8 HW support")
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191101173045.27099-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: SOF: Kconfig: add EXPERT dependency for developer options, clarify help

Some distros select all possible options, despite existing warnings to
be careful. This leads to e.g. user reports that the HDaudio codec and
DMIC are not handled by SOF.

Add an explicit menu item to unlock developer options, and make them
dependent on CONFIG_EXPERT. Hopefully with this double-lock these
options will only be selected by developers.

GitHub issue: https://github.com/thesofproject/sof/issues/1885
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191101173045.27099-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: Intel: add mutual exclusion between SOF and legacy Baytrail driver

This legacy driver is already deprecated, let's make sure there is no
conflict with SOF.

Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191101173045.27099-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: SOF: Intel: Broadwell: clarify mutual exclusion with legacy driver

Some distros select all options blindly, which leads to confusion and
bug reports. SOF does not fully support Broadwell due to firmware
dependencies, the machine drivers can only support one option, and
UCM/topology files are still being propagated to downstream distros,
so make SOF on Broadwell an opt-in option that first require distros
to opt-out of existing defaults.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=204237
Fixes: f35bf70f61d3 ('ASoC: Intel: Make sure BDW based machine drivers build for SOF')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191101173045.27099-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: SOF: Intel: Baytrail: clarify mutual exclusion with Atom/SST driver

Some distros select all options blindly, which leads to confusion and
bug reports. Since SOF does not support Baytrail-CR for now, and
UCM/topology files are still being propagated to downstream distros,
make SOF on Baytrail an opt-in option that first require distros to
opt-out of existing defaults.

Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191101173045.27099-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: SOF: Intel: hda: Simplify the hda_dsp_wait_d0i3c_done() function

Remove the retry argument for the hda_dsp_wait_d0i3c_done()
function and use the HDA_DSP_REG_POLL_RETRY_COUNT macro
directly.

Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191101170916.26517-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: Intel: boards: Add CML m/c using RT1011 and RT5682

Machine driver to enable
RT5682 on SSP0, DMIC, HDMI and
RT1011 AMP on SSP1 with
2 CH / 24 bit TDM Playback over 4 individual codecs and
4 CH / 24 bit Capture to provide feedback.

Signed-off-by: Naveen Manohar <naveen.m@intel.com>
Signed-off-by: Sathya Prakash M R <sathya.prakash.m.r@intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191101171847.26767-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: Intel: Add acpi match for rt1011 based m/c driver

Add match for CML m/c with RT1011 and RT5682

Signed-off-by: Naveen Manohar <naveen.m@intel.com>
Signed-off-by: Sathya Prakash M R <sathya.prakash.m.r@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191101171847.26767-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: ux500: Remove redundant variable "status"

local variable "status" is not used. hence it is safe to remove and
just return 0.

Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Link: https://lore.kernel.org/r/1572528855-25990-1-git-send-email-zhongjiang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: hdac_hda: fix race in device removal

When ASoC card instance is removed containing a HDA codec,
hdac_hda_codec_remove() may run in parallel with codec resume.
This will cause problems if the HDA link is freed with
snd_hdac_ext_bus_link_put() while the codec is still in
middle of its resume process.

To fix this, change the order such that pm_runtime_disable()
is called before the link is freed. This will ensure any
pending runtime PM action is completed before proceeding
to free the link.

This issue can be easily hit with e.g. SOF driver by loading and
unloading the drivers.

Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191101170635.26389-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: rt1011: some minor changes to improve readability

There is no other code use the RT1011_INIT_REG_LEN definition,
except rt1011_reg_init().
Hence, we remove it and fix the typo.

Signed-off-by: Shuming Fan <shumingf@realtek.com>
Link: https://lore.kernel.org/r/20191031115446.21108-1-shumingf@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: rt1011: add the range check for temperature_calib from device property

The driver will check the range for temperature_calib.
It should be from 1 to 255.

Signed-off-by: Shuming Fan <shumingf@realtek.com>
Link: https://lore.kernel.org/r/20191031115436.21055-1-shumingf@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: rt1011: remove unnecessary tabs using spaces instead

There are unnecessary tabs inside some statements.
It uses sapces instead.

Signed-off-by: Shuming Fan <shumingf@realtek.com>
Link: https://lore.kernel.org/r/20191031115425.21003-1-shumingf@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>