Bluetooth: hidp: fix sending output reports on intr channel

According to the specifications, data output reports must be sent on the
interrupt channel. See also usbhid implementation.
Sending these reports on the control channel breaks newer Wii Remotes.

Note that this will make output reports asynchronous. However, that's how
hid_output_raw_report() is supposed to work with HID_OUTPUT_REPORT as
report type. There are no responses to output reports.

Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: hidp: don't send boot-protocol messages as HID-reports

If a device is registered as HID device, it is always in Report-Mode.
Therefore, we must not send Boot-Protocol messages on
hidinput_input_event() callbacks. This confuses devices and may cause
disconnects on protocol errors.

We disable the hidinput_input_event() callback for now. We can implement
it properly later, but lets first fix the current code by disabling it.

Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: hidp: merge 'send' functions into hidp_send_message()

We handle skb buffers all over the place, even though we have
hidp_send_*_message() helpers. This creates a more generic
hidp_send_message() helper and uses it instead of dealing with transmit
queues directly everywhere.

Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: hidp: merge hidp_process_{ctrl,intr}_transmit()

Both hidp_process_ctrl_transmit() and hidp_process_intr_transmit() are
exactly the same apart from the transmit-queue and socket pointers.
Therefore, pass them as argument and merge both functions into one so we
avoid 25 lines of code-duplication.

Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: hidp: handle kernel_sendmsg() errors correctly

We shouldn't push back the skbs if kernel_sendmsg() fails. Instead, we
terminate the connection and drop the skb. Only on EAGAIN we push it back
and return.
l2cap doesn't return EAGAIN, yet, but this guarantees we're safe if it
will at some time in the future.

Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: hidp: remove old session-management

We have the full new session-management now available so lets switch over
and remove all the old code. Few semantics changed, so we need to adjust
the sock.c callers a bit. But this mostly simplifies the logic.

Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: hidp: add new session-management helpers

This is a rewrite of the HIDP session management. It implements HIDP as an
l2cap_user sub-module so we get proper notification when the underlying
connection goes away.

The helpers are not yet used but only added in this commit. The old
session management is still used and will be removed in a following patch.

The old session-management was flawed. Hotplugging is horribly broken and
we have no way of getting notified when the underlying connection goes
down. The whole idea of removing the HID/input sub-devices from within the
session itself is broken and suffers from major dead-locks. We never can
guarantee that the session can unregister itself as long as we use
synchronous shutdowns. This can only work with asynchronous shutdowns.
However, in this case we _must_ be able to unregister the session from the
outside as otherwise the l2cap_conn object might be unlinked before we
are.

The new session-management is based on l2cap_user. There is only one
way how to add a session and how to delete a session: "probe" and "remove"
callbacks from l2cap_user.
This guarantees that the session can be registered and unregistered at
_any_ time without any synchronous shutdown.
On the other hand, much work has been put into proper session-refcounting.
We can unregister/unlink the session only if we can guarantee that it will
stay alive. But for asynchronous shutdowns we never know when the last
user goes away so we must use proper ref-counting.

The old ->conn field has been renamed to ->hconn so we can reuse ->conn in
the new session management. No other existing HIDP code is modified.

Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: l2cap: add l2cap_user sub-modules

Several sub-modules like HIDP, rfcomm, ... need to track l2cap
connections. The l2cap_conn->hcon->dev object is used as parent for sysfs
devices so the sub-modules need to be notified when the hci_conn object is
removed from sysfs.

As submodules normally use the l2cap layer, the l2cap_user objects are
registered there instead of on the underlying hci_conn object. This avoids
any direct dependency on the HCI layer and lets the l2cap core handle any
specifics.

This patch introduces l2cap_user objects which contain a "probe" and
"remove" callback. You can register them on any l2cap_conn object and if
it is active, the "probe" callback will get called. Otherwise, an error is
returned.

The l2cap_conn object will call your "remove" callback directly before it
is removed from user-space. This allows you to remove your submodules
_before_ the parent l2cap_conn and hci_conn object is removed.

At any time you can asynchronously unregister your l2cap_user object if
your submodule vanishes before the l2cap_conn object does.

There is no way around l2cap_user. If we want wire-protocols in the
kernel, we always want the hci_conn object as parent in the sysfs tree. We
cannot use a channel here since we might need multiple channels for a
single protocol.
But the problem is, we _must_ get notified when an l2cap_conn object is
removed. We cannot use reference-counting for object-removal! This is not
how it works. If a hardware is removed, we should immediately remove the
object from sysfs. Any other behavior would be inconsistent with the rest
of the system. Also note that device_del() might sleep, but it doesn't
wait for user-space or block very long. It only _unlinks_ the object from
sysfs and the whole device-tree. Everything else is handled by ref-counts!
This is exactly what the other sub-modules must do: unlink their devices
when the "remove" l2cap_user callback is called. They should not do any
cleanup or synchronous shutdowns.

Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: l2cap: introduce l2cap_conn ref-counting

If we want to use l2cap_conn outside of l2cap_core.c, we need refcounting
for these objects. Otherwise, we cannot synchronize l2cap locks with
outside locks and end up with deadlocks.

Hence, introduce ref-counting for l2cap_conn objects. This doesn't affect
l2cap internals at all, as they use a direct synchronization.
We also keep a reference to the parent hci_conn for locking purposes as
l2cap_conn depends on this. This doesn't affect the connection itself but
only the lifetime of the (dead) object.

Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: hidp: move hidp_schedule() to core.c

There is no reason to keep this helper in the header file. No other file
depends on it so move it into hidp/core.c where it belongs.

Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: allow constant arguments for bacmp()/bacpy()

There is no reason to require the source arguments to be writeable so fix
this to allow constant source addresses.

Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: hidp: test "terminate" before sleeping

The "terminate" flag is guaranteed to be set before the session terminates
and the handlers are woken up. Hence, we need to add it to the
sleep-condition.

Note that testing the flags is not enough as nothing prevents us from
setting the flags again after the session-handler terminated.

Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: hidp: remove unused session->state field

This field is always BT_CONNECTED. Remove it and set it to BT_CONNECTED in
hidp_copy_session() unconditionally.

Also note that this field is totally bogus. Userspace can query an
hidp-session for its state. However, whenever user-space queries us, this
field should be BT_CONNECTED. If it wasn't BT_CONNECTED, then we would be
currently cleaning up the session and the session itself would exit in the
next few milliseconds. Hence, there is no reason to let user-space know
that the session will exit now if they cannot make _any_ use of that.

Thus, remove the field and let user-space think that a session is always
BT_CONNECTED as long as they can query it.

Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: introduce hci_conn ref-counting

We currently do not allow using hci_conn from outside of HCI-core.
However, several other users could make great use of it. This includes
HIDP, rfcomm and all other sub-protocols that rely on an active
connection.

Hence, we now introduce hci_conn ref-counting. We currently never call
get_device(). put_device() is exclusively used in hci_conn_del_sysfs().
Hence, we currently never have a greater device-refcnt than 1.
Therefore, it is safe to move the put_device() call from
hci_conn_del_sysfs() to hci_conn_del() (it's the only caller). In fact,
this even fixes a "use-after-free" bug as we access hci_conn after calling
hci_conn_del_sysfs() in hci_conn_del().

From now on we can add references to hci_conn objects in other layers
(like l2cap_sock, HIDP, rfcomm, ...) and grab a reference via
hci_conn_get(). This does _not_ guarantee, that the connection is still
alive. But, this isn't what we want. We can simply lock the hci_conn
device and use "device_is_registered(hci_conn->dev)" to test that.
However, this is hardly necessary as outside users should never rely on
the HCI connection to be alive, anyway. Instead, they should solely rely
on the device-object to be available.
But if sub-devices want the hci_conn object as sysfs parent, they need to
be notified when the connection drops. This will be introduced in later
patches with l2cap_users.

Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: remove unneeded hci_conn_hold/put_device()

hci_conn_hold/put_device() is used to control when hci_conn->dev is no
longer needed and can be deleted from the system. Lets first look how they
are currently used throughout the code (excluding HIDP!).

All code that uses hci_conn_hold_device() looks like this:
    ...
    hci_conn_hold_device();
    hci_conn_add_sysfs();
    ...
On the other side, hci_conn_put_device() is exclusively used in
hci_conn_del().

So, considering that hci_conn_del() must not be called twice (which would
fail horribly), we know that hci_conn_put_device() is only called _once_
(which is in hci_conn_del()).
On the other hand, hci_conn_add_sysfs() must not be called twice, either
(it would call device_add twice, which breaks the device, see
drivers/base/core.c). So we know that hci_conn_hold_device() is also
called only once (it's only called directly before hci_conn_add_sysfs()).

So hold and put are known to be called only once. That means we can safely
remove them and directly call hci_conn_del_sysfs() in hci_conn_del().

But there is one issue left: HIDP also uses hci_conn_hold/put_device().
However, this case can be ignored and simply removed as it is totally
broken. The issue is, the only thing HIDP delays with
hci_conn_hold_device() is the removal of the hci_conn->dev from sysfs.
But, the hci_conn device has no mechanism to get notified when its own
parent (hci_dev) gets removed from sysfs. hci_dev_hold/put() does _not_
control when it is removed but only when the device object is created
and destroyed.
And hci_dev calls hci_conn_flush_*() when it removes itself from sysfs,
which itself causes hci_conn_del() to be called, but it does _not_ cause
hci_conn_del_sysfs() to be called, which is wrong.

Hence, we fix it to call hci_conn_del_sysfs() in hci_conn_del(). This
guarantees that a hci_conn object is removed from sysfs _before_ its
parent hci_dev is removed.

The changes to HIDP look scary, wrong and broken. However, if you look at
the HIDP session management, you will notice they're already broken in the
exact _same_ way (ever tried "unplugging" HIDP devices? Breaks _all_ the
time).
So this patch only makes HIDP look _scary_ and _obviously broken_. It does
not break HIDP itself, it already is!

See later patches in this series which fix HIDP to use proper
session-management.

Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Reject SCO when hci connection timeouts

This patch sends Reject Synchronous Connection Request Command when
hci_conn_timeout is triggered, and the SCO connection is in BT_CONNECT2
state. It prevents inconsistency if the remote host doesn't implement
properly the timeout for the connection request, and it removes the
connection reference left when the socket is closed for incoming SCO
connections.

[ 2650.129080] sco_sock_release: sock ffff8801ca417400, sk ffff88020c408800
[ 2650.129092] sco_sock_clear_timer: sock ffff88020c408800 state 6
[ 2650.129101] __sco_sock_close: sk ffff88020c408800 state 6 socket
ffff8801ca417400
[ 2650.129108] sco_chan_del: sk ffff88020c408800, conn ffff8801c650ea20,
err 104
[ 2650.129114] hci_conn_put: hcon ffff88020c40a800 orig refcnt 1
[ 2650.129128] sco_sock_kill: sk ffff88020c408800 state 9
[ 2650.129135] sco_sock_destruct: sk ffff88020c408800
[ 2650.138468] hci_conn_timeout: hcon ffff88020c40a800 state BT_CONNECT2

Signed-off-by: Claudio Takahasi <claudio.takahasi@openbossa.org>
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Remove unneeded parameter

This patch removes the status parameter of the l2cap_conn_add function.
The parameter 'status' is always 0.

Signed-off-by: Claudio Takahasi <claudio.takahasi@openbossa.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Minor coding style fix

This patch removes unneeded initialization and empty line.

Signed-off-by: Claudio Takahasi <claudio.takahasi@openbossa.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Use GFP_KERNEL in sco_conn_add

This patch changes the memory allocation flags in the sco_conn_add
function, replacing the type to GFP_KERNEL. This function is executed
in process context and it is not called inside an atomic section.

Signed-off-by: Claudio Takahasi <claudio.takahasi@openbossa.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Fix SCO connection reference

This patch fixes decrementing SCO connection reference right after
stablishing the SCO connection with defer setup enabled. The dump below
shows a disconnection command with handle 0, the connection is still in
BT_CONNECT2 state and there isn't a handle associated with it.

< HCI Command: Accept Synchronous Connection (0x01|0x0029) plen 21
  bdaddr 78:47:1D:B3:72:6C
> HCI Event: Command Status (0x0f) plen 4
  Accept Synchronous Connection (0x01|0x0029) status 0x00 ncmd 1
< HCI Command: Disconnect (0x01|0x0006) plen 3
  handle 0 reason 0x13
  Reason: Remote User Terminated Connection
> HCI Event: Command Status (0x0f) plen 4
  Disconnect (0x01|0x0006) status 0x00 ncmd 1
> HCI Event: Synchronous Connect Complete (0x2c) plen 17
  status 0x00 handle 46 bdaddr 78:47:1D:B3:72:6C
  type eSCO
  Air mode: CVSD
< SCO data: handle 46 flags 0x00 dlen 48

Signed-off-by: Claudio Takahasi <claudio.takahasi@openbossa.org>
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: rename hci_conn_put to hci_conn_drop

We use _get() and _put() for device ref-counting in the kernel. However,
hci_conn_put() is _not_ used for ref-counting, hence, rename it to
hci_conn_drop() so we can later fix ref-counting and introduce
hci_conn_put().

hci_conn_hold() and hci_conn_put() are currently used to manage how long a
connection should be held alive. When the last user drops the connection,
we spawn a delayed work that performs the disconnect. Obviously, this has
nothing to do with ref-counting for the _object_ but rather for the
keep-alive of the connection.

But we really _need_ proper ref-counting for the _object_ to allow
connection-users like rfcomm-tty, HIDP or others.

Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Use separate function for BCM92035 vendor setup

Trying to squeeze every single vendor setup routine into the same function
and have it assigned all the time is actually a bad idea. Especially since
the core can handle the absence of a setup routine perfectly fine.

To make this a lot simpler for future additions of vendor setup code,
split the BCM92035 setup into its own function and only assign it when
this specific device has been detected.

Doing it like this has the nice side benefit that we do not have to keep
a copy of the driver_info around.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: hidp: verify l2cap sockets

We need to verify that the given sockets actually are l2cap sockets. If
they aren't, we are not supposed to access bt_sk(sock) and we shouldn't
start the session if the offsets turn out to be valid local BT addresses.

That is, if someone passes a TCP socket to HIDCONNADD, then we access some
random offset in the TCP socket (which isn't even guaranteed to be valid).

Fix this by checking that the socket is an l2cap socket.

Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: hidp: remove redundant error message

We print this error twice in the first error-path so remove it. One error
message is enough.

Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Remove driver init queue from core

The driver init queue is no longer needed. This can be all handled
inside the drivers now. So remove it.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Convert BCM92035 support to driver setup callback

With the early init stage during setup, this quirk can be simplified
and kept fully inside the driver.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Add driver setup stage for early init

Some drivers require a special stage for their early init. This is
always specific to the driver or transport. So call back into driver to
allow bringing up the device.

The advantage with this stage is that the Bluetooth core is actually
handling the HCI layer now. This means that command and event processing
is available.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Add __hci_cmd_sync_ev function

This patch adds a __hci_cmd_sync_ev function, analogous to
__hci_cmd_sync except that it also takes an event parameter to indicate
that the command completes with a special event instead of command
complete. Internally this new function takes advantage of the
hci_req_add_ev function introduced in the previous patch.

The primary expected user of this new function are the setup routines of
HCI drivers which may want to send custom commands and return only when
they have completed.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Add support for custom event terminated commands

This patch adds support for having commands within HCI requests that do
not result in a command complete but some other event. This is at least
needed for some vendor specific commands to be issued in the
hdev->setup() procecure, but might also be useful for other commands.

The way that the support is implemented is by extending the skb control
buffer to have a field to indicate that the command is expected to
terminate with a special event. After sending the command each received
event can then be compared against this field through hdev->sent_cmd.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Add __hci_cmd_sync() helper function

This patch adds a helper function for sending a single HCI command
waiting for its completion and then returning back the parameters in the
resulting command complete event (if there was one).

The implementation is very similar to that of hci_req_sync() except that
instead of invocing a callback for sending HCI commands the function
constructs and sends one itself and after being woken up picks the last
received event from hdev->recv_evt (if it matches the right criteria)
and returns it.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Track received events in hdev

This patch adds tracking of received HCI events to the hci_dev struct.
This is necessary so that a subsequent patch can implement a function
for sending a single command synchronously and returning the resulting
command complete parameters in the function return value.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Remove trivial white space

This patch removes redundant whitespace from the HCI ldisc driver.

Signed-off-by: Chan-yeol Park <chanyeol.park@samsung.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Fix possible NULL dereference in hci_uart_tty_receive

This patch adds a NULL check for the HCI UART ldisc driver because some
of HCI UART drivers allow hci_uart_tty_receive function to be called
even though the HCI device hasn't been registered yet.

Signed-off-by: Chan-yeol Park <chanyeol.park@samsung.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Fix H4 crash from incoming UART packets

This patch adds a check HCI_UART_REGISTERED before reading UART data in
the HCI UART H4 driver. UART data could arrive when inside the
hci_uart_tty_ioctl function after calling test_and_set_bit for
HCI_UART_PROTO_SET but before the hci_uart_set_proto function has
returned.

Backtrace:
[<c05f27ec>] (hci_recv_stream_fragment+0x0/0x74) from [<c04126f4>] (h4_recv+0x18/0x40)
 r7:eb1d4d1c r6:eb7683b0 r5:eae8e800 r4:0000000c
[<c04126dc>] (h4_recv+0x0/0x40) from [<c0411870>] (hci_uart_tty_receive+0x6c/0x94)
 r5:eae8e800 r4:eb768380
[<c0411804>] (hci_uart_tty_receive+0x0/0x94) from [<c027be88>] (flush_to_ldisc+0x16c/0x17c)
 r6:eae8e8d8 r5:eae8e800 r4:eae8e8c8
[<c027bd1c>] (flush_to_ldisc+0x0/0x17c) from [<c0050ae8>] (process_one_work+0x144/0x4d4)
[<c00509a4>] (process_one_work+0x0/0x4d4) from [<c0051208>] (worker_thread+0x180/0x370)
[<c0051088>] (worker_thread+0x0/0x370) from [<c005617c>] (kthread+0x90/0x9c)
[<c00560ec>] (kthread+0x0/0x9c) from [<c003a3a0>] (do_exit+0x0/0x7ec)

Signed-off-by: Chan-yeol Park <chanyeol.park@samsung.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Remove unneeded hci_req_cmd_status function

This patch removes the hci_req_cmd_status function since it is not
used anymore. The HCI request framework now considers the HCI command
has complete once the Command Status or Command Complete Event is
received.

Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Fix hci_inquiry ioctl usage

Since the HCI request framework was properly fixed, the hci_req_sync
call, in hci_inquiry, will return as soon as the HCI command completes
(not the Inquiry procedure). However, in inquiry ioctl implementation,
we want to sleep the user process until the inquiry procedure finishes.

This patch changes hci_inquiry so, in case the HCI Inquiry command
was executed successfully, it waits the HCI_INQUIRY flag to be cleared.
This way, the user process will sleep until the inquiry procedure
finishes.

Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Fix HCI request framework

Some HCI commands don't send a Command Complete Event once the HCI
command has completed so they require some special handling from the
HCI request framework. These HCI commands, however, send a Command
Status Event to indicate that the command has been received, and
that the controller is currently performing the task for the command.

So, in order to properly handle those HCI commands, the HCI request
framework should consider the HCI command has completed once the
Command Status Event is received.

This way, we fix some issues regarding the Inquiry command support,
as well as add support for all those HCI commands which would require
some special handling from the HCI request framework.

Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Add support for Foxconn/Hon Hai [0489:e04d]

Add support for the AR3012 chip.

T:  Bus=01 Lev=02 Prnt=02 Port=05 Cnt=03 Dev#= 21 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0489 ProdID=e04d Rev=00.02
S:  Manufacturer=Atheros Communications
S:  Product=Bluetooth USB Host Controller
S:  SerialNumber=Alaska Day 2006
C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I:  If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb

Signed-off-by: Noguchi Kazutosi <linux@scaltinof.net>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

brcmfmac: enable sk_buff queueing when credits deplete

Firmware provides the driver with credits used to transmit packets
to the firmware. When credits run out the packets should be queued
and dequeued when receiving creditback signals from the firmware.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: no flow-control tlv signals when fcmode is NONE

The fcmode provided by module parameter defaults to NONE, which
means no flow-control is required. In this case flow-control
signals should not be enabled.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: only allocate firmware-signalling resources if required

Bail out of brcmf_fws_init() when no firmware-signalling is asked
for. Need to take this into account in brcmf_fws_deinit() as well.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: move brcmf_fws_{de,}init() functions

The functions are moved in preparation of later patches.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: correct specified length from FIFOCREDITBACK signal

The length is not according specification so better fix it.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: initialize struct brcmf_fws_info fields before iovar

If iovar to the firmware fails the firmware-signalling module
does a cleanup for which it needs pointer to struct brcmf_pub, which
it gets from struct brcmf_fws_info::drvr. Assign this field before
doing the tlv iovar.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: add dedicated log level for low-level sdio debugging

The low-level sdio code has a large number of trace and info messages
that are mostly useful looking into bus specific issues. For tracing
higher-level driver functions it is better to have a dedicated level
for low-level sdio debugging.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Change-Id: Ia424ff18d9033b97aeffc248358e50c51805e815
Reviewed-on: http://lb-bun-88.bun.broadcom.com:8080/74
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: avoid error output on header only packet

During SDIO layer flow control signalling firmware can issue
invalid packets. Prevent printing of parsing errors in such case.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: avoid error output in receive path

Parsing the tlv upon receiving frames can fail. Instead of printing
an error message, just count the parse failure. On some devices we
receive a lot of invalid tlv signals.

this commit will be squashed.

Signed-off-by: Arend van Spriel <arend@broadcom.com>
Change-Id: I08e0f62c55e5028f9aa70c396d291679abd273c9
Reviewed-on: http://lb-bun-88.bun.broadcom.com:8080/72
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: fix handling sk_buff cleanup upon bus tx failure

When firmware-signalling is active the brcmf_txcomplete() does
a free of the sk_buff when transfer to firmware fails in the
bus-specific driver code. However, it should also cleanup the
packet from the hanger. This patch fixes that.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: enable tx status signalling

Enabling the tx status signalling, which requires packet tagging
before sending to the firmware and handling the tx status signal.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: add flow-control mode to firmware signalling

Upcoming patches will add firmware signalled flow control. Prepare
by adding the mode, which defaults to disable it. The mode can be
queried by brcmf_fws_fc_active() and set by a module parameter.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: add optional bus callback definition for tx queue cleanup

Add a callback to obtain packet queue from the bus-specific code
used to cleanup packet buffers from firmware-signalling code.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: add firmware-signalling hanger functions

The hanger for firmware-signalling is used to retain information for
outstanding transmit packets that await tx status.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: perform filtered firmware-signalling cleanup upon DEL_IF

When an interface is deleted make sure to cleanup all packet
buffers related to that interface.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: add definitions for handling sk_buff control buffer data

The sk_buff structure contains a control buffer that can be used
by different layers in the networking stack for holding packet
associated information. In brcmfmac it is used to hold firmware
signalling related information.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: allow stopping netif queue for different reasons

Currently, the netif queue is only stopped when the bus interface is
giving a push back. This will change soon so prepare the driver by
adding a stop reason and stop/resume the queue accordingly.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: add firmware-signalling cleanup function

Add a cleanup function releasing any queued packet buffers in
the mac descriptor entries.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Piotr Haber <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: add handler for credit map firmware events

The firmware signalling functionality needs the credit map firmware
events. This patch adds registration of a handler for this event.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: handle firmware signal for updating mac descriptor info

Firmware can signal the driver to allocate descriptor info for a given
mac address, which will be used for flow control and host queueing.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: hookup firmware signalling to firmware interface events

Firmware signalling needs to handle resources upon interface
events. This patch add calls in the interface event handling
routine.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: determine the wiphy->bands property correctly.

Use information from the device to determine the bands property
of the wiphy object. After this change the support of 80211n is
correctly presented in the bands property.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: use skb_cow() in brcmf_sdbrcm_txpkt() to assure alignment

In brcmf_sdbrcm_txpkt() a new packet is allocated and used to transmit
to firmware freeing up the original packet. However, that packet is
still referenced in firmware-signalling so this would result in a
double free. Using skb_cow() avoids this as the packet reference is
unchanged.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: minor optimization of brcmf_sdbrcm_txpkt() function

When taking care of packet alignment to 64-byte boundary padding may
be added between SDPCM header and CDC data. It clear both SDPCM header
space and padding space. Changed it to only clear padding space. In
filling the SDPCM header it uses unaligned access to set SDPCM software
header, but preceding code assures it is properly aligned.

Signed-off-by: Arend van Spriel <arend@broadcom.com>
Change-Id: Iad22f277f3496440ba4d2db771205714774570ac
Reviewed-on: http://lb-bun-88.bun.broadcom.com:8080/76
Reviewed-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: correct success flag passed by brcmf_sdbrcm_txpkt()

The function brcmf_sdbrcm_txpkt() calls brcmf_txcomplete() with
a parameter success. For this parameter it passes ret != 0, but
that condition is true upon failure.

Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8188ee: Fix wrong header patch

This patch is to fix some wrong header file path.
It has caused the build failed.

Signed-off-by: Chen, Chien-Chia <machen@suse.com>
Cc: larry.finger@lwfinger.net
Cc: zhiyuan_yang@realsil.com.cn
Cc: page_he@realsil.com.cn
Cc: mmarek@suse.cz
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Revert "NFC: microread: Fix MEI build failure"

This reverts commit 63cd353c34a08af2d1935f8d0c2b6b091714ff79.

We no longer need this fix as the MEI bus APIs are now merged into
char-misc-next.

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8188ee: Enable build of new driver

These changes enable building the new driver.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: jcheung@suse.com
Cc: machen@suse.com
Cc: mmarek@suse.cz
Cc: zhiyuan_yang@realsil.com.cn
Cc: page_he@realsil.com.cn
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8188ee: Enable recognition of RTL8188EE

These patches modify the common probe routine to recognize the RTL8188EE
chip and implement asynchronous firmware reading in the callback routine
to initialize the sw variables.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: jcheung@suse.com
Cc: machen@suse.com
Cc: mmarek@suse.cz
Cc: zhiyuan_yang@realsil.com.cn
Cc: page_he@realsil.com.cn
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8192c: rtl8192ce: rtl8192cu: rtl8192de: rtl8723ae: Add changes required by adding rtl81988ee

This patch combines the remaining changes in the rtlwifi family to handle
the addition of rtl8188ee. A number of these changes eliminate some CamelCase
variable names, and other shorten common variable names so that long lines
in the new driver could be shortened.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: jcheung@suse.com
Cc: machen@suse.com
Cc: mmarek@suse.cz
Cc: zhiyuan_yang@realsil.com.cn
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8188ee: Add new driver

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: jcheung@suse.com
Cc: machen@suse.com
Cc: mmarek@suse.cz
Cc: page_he@realsil.com.cn
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: Rework rtl_lps_leave() and rtl_lps_enter() to use work queue

In commit a5ffbe0, some of the calls to rtl_lps_leave() were switched
to be called from a work queue to avoid a scheduling while atomic bug.
This patch converts the remaining calls to use the work queue. In
addition, the call to rtl_lps_enter() is also switched to the work
queue. None of these newly converted calls had triggered the bug (yet),
but this change make all of them fit a single pattern.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: jcheung@suse.com
Cc: machen@suse.com
Cc: mmarek@suse.cz
Cc: zhiyuan_yang@realsil.com.cn
Cc: page_he@realsil.com.cn
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8192c: rtl8192ce: Update to vendor driver of 2013.02.07

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: jcheung@suse.com
Cc: machen@suse.com
Cc: mmarek@suse.cz
Cc: zhiyuan_yang@realsil.com.cn
Cc: page_he@realsil.com.cn
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8723ae: Update to vendor driver of 2013.02.07

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: jcheung@suse.com
Cc: machen@suse.com
Cc: mmarek@suse.cz
Cc: zhiyuan_yang@realsil.com.cn
Cc: page_he@realsil.com.cn
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8192se: Update driver to match vendor driver of 2013.02.07

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: jcheung@suse.com
Cc: machen@suse.com
Cc: mmarek@suse.cz
Cc: zhiyuan_yang@realsil.com.cn
Cc: page_he@realsil.com.cn
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi Modify existing bits to match vendor version 2013.02.07

These changes add the new variables for P2P and modify the various struct
definitions for other new features.

This patch updates files base.{c,h} for the changes in the newest vendor
driver.

This patch updates files ps.{c,h} for the changes in the newest vendor
driver.

This patch updates files debug.{c,h}, efuse.c, pci.{c,h}, and wifi.h for
the changes in the newest vendor driver.

This patch updates files core.c, ps.c, rc.c, and wifi.h for
the changes in the newest vendor driver.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: jcheung@suse.com
Cc: machen@suse.com
Cc: mmarek@suse.cz
Cc: zhiyuan_yang@realsil.com.cn
Cc: page_he@realsil.com.cn
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: rt2800lib: probe RT chipset earlier

The 'rt2800_validate_eeprom' function uses the type of
the RT chipset for verifying the number of RX streams
on RT28x0 devices. However the type of the RT chipset
is not yet detected when the 'rt2800_validate_eeprom'
function is called.

Move the RT chipset detection code into a separate helper
function, and call it before rt2800_validate_eeprom.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: rt2800lib: separate RT and RF chipset detection

Use the newly introduced rt2x00_set_{rf,rt} helpers
to set the RT and RF chipset separately.

This change makes it possible to move the RT
detection code into another function which will
be done in a subseqent patch.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: introduce rt2x00_set_{rt,rf} helpers

The new helpers can be used to set the type of the
RT and RF chipsets separately.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: make struct b2056_inittabs_pts const

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: mark some functions and structs static

This fixes some sparse warnings.

b43_nphy_set_rxantenna() was not used anywhere.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: use separate AMPDU tx/rx window sizes in 11ac networks

Newer 11ac enabled chipsets have more TX and RX buffers in FW
and hardware; so they may support larger TX and RX window sizes
for BA. Reset BA settings during association, adhoc join/start
or start_ap() if we are joining/creating 11ac network.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Sagar Bijwe <bsagar@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: change default tx/rx win_size for BA setup

This patch fixes an issue where RX throughput values observed
were substantially lower than TX counterparts for PCIe8897 STA.
PCIe8897 supports larger rx_win_size. After changing these values
we see big improvement for TX and RX throughput values.

Different tx_win_size and rx_win_size are used for AP mode.

All BA setup related initialization has been moved to separate
function.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Sagar Bijwe <bsagar@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'master' of git://git./linux/kernel/git/linville/wireless

Conflicts:
net/mac80211/sta_info.c
net/wireless/core.h

brcmsmac: remove some pmu functions and use the bcma equivalents

This removes the following functions:
si_pmu_chipcontrol() => bcma_chipco_chipctl_maskset()
si_pmu_regcontrol() => bcma_chipco_regctl_maskset()
si_pmu_pllcontrol() => bcma_chipco_pll_maskset()
si_pmu_pllupd() => bcma_cc_set32()
si_pmu_alp_clock() => bcma_chipco_get_alp_clock()

This also removed the sih member from struct shared_phy.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

bcma: export some gpio functions

These functions will be used by brcmsmac.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

bcma: export bcma_chipco_get_alp_clock()

This function will be used by brcmsmac.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

bcma: handle more devices in bcma_pmu_get_alp_clock()

Add some more chip IDs to bcma_pmu_get_alp_clock()

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

bcma: use BCMA_CC_PMU_CTL_* constants

Instead of hard coding these values use the existing constants.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

bcma: mark eromptr as __iomem

This fixes some sparse warnings.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Show actual timeout value in failed calibration messages.

The messages are currently hard coding "1ms", which does not match
the actual timeout being used.

Signed-off-by: Robert Shade <robert.shade@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

carl9170: remove fast channel change feature

Marco Fonseca reported a issue with his carl9170 device:
"I'm seeing a problem with the carl driver. If I change channels
repeatedly on the 2.4ghz band, monitoring (e.g. tcpdump) will
eventually halt.  I've seen this on various versions of the carl
driver/firmware (both from 1.9.4 to 1.9.7)"
<http://marc.info/?l=linux-wireless&m=136381302428113>

The culprit was identified as "fast channel change feature" which
according to Adrian Chadd is: "... notoriously unreliable and
really only fully debugged on some very later chips."
<http://marc.info/?l=linux-wireless&m=136416984531380>

Therefore, this patch removes the fast channel change feature.
The phy will now always have to go through a cold reset when
changing channels, but it should no longer become deaf.

Cc: Marco Fonseca <marco@tampabay.rr.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwl8k: always apply configuration even when device is idle

Fix settings not being applied when the device is idle and the firmware
gets reloaded (because of changing from STA to AP mode). This caused
the device using the wrong channel (and likely band), e.g. a 5 GHz only
card still defaulted to channel 6 in the 2.4 GHz band when left
unconfigured.

This issue was always present, but only made visible with "mwl8k: Do not
call mwl8k_cmd_set_rf_channel unconditionally" (0f4316b9), since before
that the channel was (re-)configured at the next _config call even when
it did not change from the mac80211 perspective.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmsmac: add support for adhoc mode

This adds adhoc mode support to brcmsmac.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmsmac: activate AP support

This activates the AP mode support.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmsmac: deactivate ucode sending probe responses

It is possible to configure the ucode to automatically send the probe
responses to the clients after they send a probe request. At least for
WPS the userspace needs to answer the probe requests and we do not know
a way to say to the ucode to just handle the normal probe requests, so
for now no probe requests should be handled by the ucode.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmsmac: add support for probe response template

The ucode is able to answer probe response by itself. This writes such
a template into the specific memory. Currently the probe requests are
also send to mac80211 so there are more answers send to a requesting
client. We have to make the ucode stop sending probe requests to the
driver.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmsmac: react on changing SSID

To send the correct probe response the hardware needs to know the SSID
when it changed.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmsmac: add beacon template support

This makes it possible that a beacon template provided by mac80211 is
written to the hardware for constant beaconing.

This is based on an old version of brcmsmac, on b43 and the spec b43 is
based on.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmsmac: write beacon period to hardware

Make brcms_c_set_beacon_period() write the beacon period to the
hardware if a new one is set.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmsmac: remove brcms_pub->bcmerr

This was a write only member

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmsmac: remove brcms_bss_cfg->cur_etheraddr

use brcms_pub->cur_etheraddr instead

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>