Frans Pop [Mon, 26 Oct 2009 07:39:03 +0000 (08:39 +0100)]
thermal: Only set passive_delay for forced_passive cooling
Setting polling_delay is useless as passive_delay has priority,
so the value shown in proc isn't the actual polling delay. It
also gives the impression to the user that he can change the
polling interval through proc, while in fact he can't.
Also, unset passive_delay when the forced passive trip point is
unbound to allow polling to be disabled.
Signed-off-by: Frans Pop <elendil@planet.nl>
Acked-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Frans Pop [Mon, 26 Oct 2009 07:39:02 +0000 (08:39 +0100)]
thermal: add sanity check for the passive attribute
Values below 1000 milli-celsius don't make sense and can cause the
system to go into a thermal heart attack: the actual temperature
will always be lower and thus the system will be throttled down to
its lowest setting.
An additional problem is that values below 1000 will show as 0 in
/proc/acpi/thermal/TZx/trip_points:passive.
cat passive
0
echo -n 90 >passive
bash: echo: write error: Invalid argument
echo -n 90000 >passive
cat passive
90000
Signed-off-by: Frans Pop <elendil@planet.nl>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Frans Pop [Mon, 26 Oct 2009 07:39:01 +0000 (08:39 +0100)]
acpi: thermal: display forced passive trip points in proc
Users can force a passive trip point for a thermal zone that does not
have _PSV defined in ACPI by setting the passive attribute in sysfs.
It's useful to display such trip points in /proc/acpi/thermal_zone.
.../TZ1/cooling_mode:<setting not supported>
.../TZ1/polling_frequency:polling frequency: 10 seconds
.../TZ1/state:state: ok
.../TZ1/temperature:temperature: 53 C
.../TZ1/trip_points:critical (S5): 110 C
.../TZ1/trip_points:passive (forced): 95 C
And if not set (passive is 0):
.../TZ1/trip_points:passive (forced):<not set>
Signed-off-by: Frans Pop <elendil@planet.nl>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Frans Pop [Mon, 26 Oct 2009 07:39:00 +0000 (08:39 +0100)]
thermal: sysfs-api.txt - document passive attribute for thermal zones
Signed-off-by: Frans Pop <elendil@planet.nl>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Frans Pop [Mon, 26 Oct 2009 07:38:59 +0000 (08:38 +0100)]
thermal: sysfs-api.txt - reformat for improved readability
The document currently uses large indentations which make the text
too wide for easy readability. Also improve general consistency.
Signed-off-by: Frans Pop <elendil@planet.nl>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Amit Kucheria [Fri, 16 Oct 2009 09:46:02 +0000 (12:46 +0300)]
acpi: thermal: Add EOL to the trip_point_N_type strings
Make the trip_point_N_type sysfs files return a string ending in EOL for
consistency with other sysfs files.
Signed-off-by: Amit Kucheria <amit.kucheria@canonical.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Julia Lawall [Sat, 17 Oct 2009 06:34:39 +0000 (08:34 +0200)]
ACPI: Move dereference after NULL test
If the NULL test on pr is needed, then the dereference should be after the
NULL test.
A simplified version of the semantic match that detects this problem is as
follows (http://coccinelle.lip6.fr/):
// <smpl>
@match exists@
expression x, E;
identifier fld;
@@
* x->fld
... when != \(x = E\|&x\)
* x == NULL
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Rakib Mullick [Thu, 5 Nov 2009 21:51:40 +0000 (16:51 -0500)]
ACPI: add __cpuinit to acpi_processor_add()
Annote acpi_processor_add with cpuinit since it calls a cpuinit function
acpi_processor_power_init and fixes a section mismatch warning.
We were warned by the following warning:
LD drivers/acpi/processor.o
WARNING: drivers/acpi/processor.o(.text+0x1829): Section mismatch in
reference from the function acpi_processor_add() to the function
.cpuinit.text:acpi_processor_power_init()
The function acpi_processor_add() references
the function __cpuinit acpi_processor_power_init().
This is often because acpi_processor_add lacks a __cpuinit
annotation or the annotation of acpi_processor_power_init is wrong.
Signed-off-by: Rakib Mullick <rakib.mullick@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Darrick J. Wong [Thu, 22 Oct 2009 01:01:37 +0000 (18:01 -0700)]
acpi-power-meter: Don't leak ACPI error codes to userspace
If the ACPI methods return an error code, we must return -EINVAL to userspace
to flag the error. Right now we pass the (positive) number right through,
which causes echo to keep writing bogus values.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Arjan van de Ven [Thu, 1 Oct 2009 22:48:40 +0000 (15:48 -0700)]
ACPI: clean up video.c boundary checks and types
proc.c and video.c are a bit sloppy around types and style,
confusing gcc for a new feature that'll be in 2.6.33 and will
cause a warning on the current code.
This patch changes
if (foo + 1 > sizeof bar)
into
if (foo >= sizeof(bar))
which is more kernel-style.
it also changes a variable in proc.c to unsigned; it gets assigned
a value from an unsigned type, and is then only compared for > not
for negative, so using unsigned is just outright the right type
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Linus Torvalds [Fri, 16 Oct 2009 00:41:50 +0000 (17:41 -0700)]
Linux 2.6.32-rc5
Linus Torvalds [Thu, 15 Oct 2009 22:21:42 +0000 (15:21 -0700)]
Merge branch 'docs-next' of git://git.lwn.net/linux-2.6
* 'docs-next' of git://git.lwn.net/linux-2.6:
Update flex_arrays.txt
Linus Torvalds [Thu, 15 Oct 2009 22:21:20 +0000 (15:21 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/teigland/dlm
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/teigland/dlm:
dlm: fix socket fd translation
dlm: fix lowcomms_connect_node for sctp
Linus Torvalds [Thu, 15 Oct 2009 22:20:17 +0000 (15:20 -0700)]
Merge branch 'x86-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
Revert "x86: linker script syntax nits"
x86, perf_event: Rename 'performance counter interrupt'
David Howells [Thu, 15 Oct 2009 09:14:35 +0000 (10:14 +0100)]
KEYS: get_instantiation_keyring() should inc the keyring refcount in all cases
The destination keyring specified to request_key() and co. is made available to
the process that instantiates the key (the slave process started by
/sbin/request-key typically). This is passed in the request_key_auth struct as
the dest_keyring member.
keyctl_instantiate_key and keyctl_negate_key() call get_instantiation_keyring()
to get the keyring to attach the newly constructed key to at the end of
instantiation. This may be given a specific keyring into which a link will be
made later, or it may be asked to find the keyring passed to request_key(). In
the former case, it returns a keyring with the refcount incremented by
lookup_user_key(); in the latter case, it returns the keyring from the
request_key_auth struct - and does _not_ increment the refcount.
The latter case will eventually result in an oops when the keyring prematurely
runs out of references and gets destroyed. The effect may take some time to
show up as the key is destroyed lazily.
To fix this, the keyring returned by get_instantiation_keyring() must always
have its refcount incremented, no matter where it comes from.
This can be tested by setting /etc/request-key.conf to:
#OP TYPE DESCRIPTION CALLOUT INFO PROGRAM ARG1 ARG2 ARG3 ...
#====== ======= =============== =============== ===============================
create * test:* * |/bin/false %u %g %d %{user:_display}
negate * * * /bin/keyctl negate %k 10 @u
and then doing:
keyctl add user _display
aaaaaaaa @u
while keyctl request2 user test:x test:x @u &&
keyctl list @u;
do
keyctl request2 user test:x test:x @u;
sleep 31;
keyctl list @u;
done
which will oops eventually. Changing the negate line to have @u rather than
%S at the end is important as that forces the latter case by passing a special
keyring ID rather than an actual keyring ID.
Reported-by: Alexander Zangerl <az@bond.edu.au>
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Alexander Zangerl <az@bond.edu.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 15 Oct 2009 22:15:03 +0000 (15:15 -0700)]
Merge branch 'merge' of git://git./linux/kernel/git/benh/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/pci: Fix MODPOST warning
powerpc/oprofile: Add ppc750 CL as supported by oprofile
powerpc: warning: allocated section `.data_nosave' not in segment
powerpc/kgdb: Fix build failure caused by "kgdb.c: unused variable 'acc'"
powerpc: Fix hypervisor TLB batching
powerpc/mm: Fix hang accessing top of vmalloc space
powerpc: Fix memory leak in axon_msi.c
powerpc/pmac: Fix issues with sleep on some powerbooks
powerpc64/ftrace: use PACA to retrieve TOC in mod_return_to_handler
powerpc/ftrace: show real return addresses in modules
Linus Torvalds [Thu, 15 Oct 2009 22:10:27 +0000 (15:10 -0700)]
Merge branch 'release' of git://git./linux/kernel/git/lenb/linux-acpi-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI button: don't try to use a non-existent lid device
ACPI: video: Loosen strictness of video bus detection code
eeepc-laptop: Prevent a panic when disabling RT2860 wireless when associated
eeepc-laptop: Properly annote eeepc_enable_camera().
ACPI / PCI: Fix NULL pointer dereference in acpi_get_pci_dev() (rev. 2)
fujitsu-laptop: address missed led-class ifdef fixup
ACPI: Kconfig, fix proc aggregator text
ACPI: add AC/DC notifier
Linus Torvalds [Thu, 15 Oct 2009 22:09:55 +0000 (15:09 -0700)]
Merge branch 'omap-fixes-for-linus' of git://git./linux/kernel/git/tmlind/linux-omap-2.6
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
OMAP2xxx clock: set up clockdomain pointer in struct clk
OMAP: Fix race condition with autodeps
omap: McBSP: Fix incorrect receiver stop in omap_mcbsp_stop
omap: Initialization of SDRC params on Zoom2
omap: RX-51: Drop I2C-1 speed to 2200
omap: SDMA: Fixing bug in omap_dma_set_global_params()
omap: CONFIG_ISP1301_OMAP redefined in Beagle defconfig
Linus Torvalds [Thu, 15 Oct 2009 22:06:37 +0000 (15:06 -0700)]
Merge branch 'master' of git://git./linux/kernel/git/mason/btrfs-unstable
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
Btrfs: always pin metadata in discard mode
Btrfs: enable discard support
Btrfs: add -o discard option
Btrfs: properly wait log writers during log sync
Btrfs: fix possible ENOSPC problems with truncate
Btrfs: fix btrfs acl #ifdef checks
Btrfs: streamline tree-log btree block writeout
Btrfs: avoid tree log commit when there are no changes
Btrfs: only write one super copy during fsync
Linus Torvalds [Thu, 15 Oct 2009 22:06:02 +0000 (15:06 -0700)]
Merge git://git./linux/kernel/git/gregkh/tty-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
tty: fix vt_compat_ioctl
Linus Torvalds [Thu, 15 Oct 2009 22:05:46 +0000 (15:05 -0700)]
Merge git://git./linux/kernel/git/gregkh/driver-core-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
sysfs: Allow sysfs_notify_dirent to be called from interrupt context.
sysfs: Allow sysfs_move_dir(..., NULL) again.
Linus Torvalds [Thu, 15 Oct 2009 22:05:33 +0000 (15:05 -0700)]
Merge git://git./linux/kernel/git/gregkh/usb-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: gadget: Fix EEM driver comments and VID/PID
usb-storage: Workaround devices with bogus sense size
USB: ehci: Fix IST boundary checking interval math.
USB: option: Support for AIRPLUS MCD650 Datacard
USB: whci-hcd: always do an update after processing a halted qTD
USB: whci-hcd: handle early deletion of endpoints
USB: wusb: don't use the stack to read security descriptor
USB: rename Documentation/ABI/.../sysfs-class-usb_host
Linus Torvalds [Thu, 15 Oct 2009 22:05:20 +0000 (15:05 -0700)]
Merge git://git./linux/kernel/git/gregkh/staging-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6:
Staging: rt2860sta: prevent a panic when disabling when associated
staging: more sched.h fixes
Staging: et131x: Fix the add_10bit macro
Staging: et131x: Correct WRAP bit handling
staging: Complete sched.h removal from interrupt.h
Staging: vme: fix sched.h build breakage
Staging: poch: fix sched.h build breakage
Staging: b3dfg: fix sched.h build breakage
Staging: comedi: fix sched.h build breakage
Staging: iio: Fix missing include <linux/sched.h>
Linus Torvalds [Thu, 15 Oct 2009 22:03:17 +0000 (15:03 -0700)]
Merge git://git./linux/kernel/git/davem/net-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (53 commits)
vmxnet: fix 2 build problems
net: add support for STMicroelectronics Ethernet controllers.
net: ks8851_mll uses mii interfaces
net/fec_mpc52xx: Fix kernel panic on FEC error
net: Fix OF platform drivers coldplug/hotplug when compiled as modules
TI DaVinci EMAC: Clear statistics register properly.
r8169: partial support and phy init for the 8168d
irda/sa1100_ir: check return value of startup hook
udp: Fix udp_poll() and ioctl()
WAN: fix Cisco HDLC handshaking.
tcp: fix tcp_defer_accept to consider the timeout
3c574_cs: spin_lock the set_multicast_list function
net: Teach pegasus driver to ignore bluetoother adapters with clashing Vendor:Product IDs
netxen: fix pci bar mapping
ethoc: fix warning from 32bit build
libertas: fix build
net: VMware virtual Ethernet NIC driver: vmxnet3
net: Fix IXP 2000 network driver building.
libertas: fix build
mac80211: document ieee80211_rx() context requirement
...
Linus Torvalds [Thu, 15 Oct 2009 21:59:24 +0000 (14:59 -0700)]
Merge the right tty-fixes branch
* branch 'tty-fixes'
tty: use the new 'flush_delayed_work()' helper to do ldisc flush
workqueue: add 'flush_delayed_work()' to run and wait for delayed work
tty: Make flush_to_ldisc() locking more robust
Jonathan Corbet [Wed, 14 Oct 2009 18:43:22 +0000 (12:43 -0600)]
Update flex_arrays.txt
The 2.6.32 merge window brought a number of changes to the flexible array
API; this patch updates the documentation to match the new state of
affairs.
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Ingo Molnar [Thu, 15 Oct 2009 06:08:12 +0000 (08:08 +0200)]
Revert "x86: linker script syntax nits"
This reverts commit
e9a63a4e559fbdc522072281d05e6b13c1022f4b.
This breaks older binutils, where sink-less asserts are broken.
See this commit for further details:
d2ba8b2: x86: Fix assert syntax in vmlinux.lds.S
Acked-by: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <
4AD6523D.
5030909@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Ingo Molnar [Thu, 15 Oct 2009 06:07:26 +0000 (08:07 +0200)]
Merge branch 'linus' into x86/urgent
Merge reason: pull in latest, to be able to revert a patch there.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Len Brown [Thu, 15 Oct 2009 04:47:13 +0000 (00:47 -0400)]
Merge branch 'misc' into release
Len Brown [Thu, 15 Oct 2009 04:46:57 +0000 (00:46 -0400)]
Merge branch 'launchpad-333386' into release
Len Brown [Thu, 15 Oct 2009 04:46:46 +0000 (00:46 -0400)]
Merge branch 'eeepc-laptop' into release
Len Brown [Thu, 15 Oct 2009 04:45:37 +0000 (00:45 -0400)]
Merge branch 'bugzilla-14129' into release
Randy Dunlap [Thu, 15 Oct 2009 03:38:58 +0000 (20:38 -0700)]
vmxnet: fix 2 build problems
vmxnet3 uses in_dev* interfaces so it should depend on INET.
Also fix so that the driver builds when CONFIG_PCI_MSI is disabled.
vmxnet3_drv.c:(.text+0x2a88cb): undefined reference to `in_dev_finish_destroy'
drivers/net/vmxnet3/vmxnet3_drv.c:1335: error: 'struct vmxnet3_intr' has no member named 'msix_entries'
drivers/net/vmxnet3/vmxnet3_drv.c:1384: error: 'struct vmxnet3_intr' has no member named 'msix_entries'
drivers/net/vmxnet3/vmxnet3_drv.c:2137: error: 'struct vmxnet3_intr' has no member named 'msix_entries'
drivers/net/vmxnet3/vmxnet3_drv.c:2138: error: 'struct vmxnet3_intr' has no member named 'msix_entries'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Bhavesh davda <bhavesh@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Benjamin Herrenschmidt [Thu, 15 Oct 2009 03:09:11 +0000 (14:09 +1100)]
Merge commit 'ftrace/ppc' into merge
Tony Lindgren [Wed, 14 Oct 2009 22:46:15 +0000 (15:46 -0700)]
Merge branch '2_6_32rc4_fixes' of git://git.pwsan.com/linux-2.6 into omap-fixes-for-linus
Andreas Schwab [Mon, 28 Sep 2009 18:10:02 +0000 (20:10 +0200)]
tty: fix vt_compat_ioctl
Call compat_unimap_ioctl, not do_unimap_ioctl.
This was broken by commit
e9216651.
The compat_unimap_ioctl was originally called do_unimap_ioctl in
fs/compat_ioctl.h which got moved to drivers/char/vt_ioctl.c.
In that patch, the caller was not updated and consequently called
the native handler.
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Paul Walmsley [Wed, 14 Oct 2009 22:40:37 +0000 (16:40 -0600)]
OMAP2xxx clock: set up clockdomain pointer in struct clk
clock24xx.c is missing a omap2_init_clk_clkdm() in its
omap2_clk_init() function. Among other bad effects, this causes the
OMAP hwmod layer to oops on boot.
Thanks to Carlos Aguiar <carlos.aguiar@indt.org.br> and Stefano
Panella <Stefano.Panella@csr.com> for reporting this bug. Thanks to Tony
Lindgren <tony@atomide.com> for N800 booting advice.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Carlos Aguiar <carlos.aguiar@indt.org.br>
Cc: Stefano Panella <Stefano.Panella@csr.com>
Cc: Tony Lindgren <tony@atomide.com>
Kalle Jokiniemi [Wed, 14 Oct 2009 22:40:37 +0000 (16:40 -0600)]
OMAP: Fix race condition with autodeps
There is a possible race condition in clockdomain
code handling hw supported idle transitions.
When multiple autodeps dependencies are being added
or removed, a transition of still remaining dependent
powerdomain can result in false readings of the
state counter. This is especially fatal for off mode
state counter, as it could result in a driver not
noticing a context loss.
Fixed by disabling hw supported state transitions
when autodeps are being changed.
Signed-off-by: Kalle Jokiniemi <kalle.jokiniemi@digia.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Linus Torvalds [Wed, 14 Oct 2009 22:36:19 +0000 (15:36 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/ieee1394/linux1394-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
firewire: sbp2: provide fallback if mgt_ORB_timeout is missing
ieee1394: add documentation entry to MAINTAINERS
ieee1394: update URLs in debugging-via-ohci1394.txt
Linus Torvalds [Wed, 14 Oct 2009 22:34:55 +0000 (15:34 -0700)]
Merge branch 'tty-fixes'
* branch 'tty-fixes':
tty: use the new 'flush_delayed_work()' helper to do ldisc flush
workqueue: add 'flush_delayed_work()' to run and wait for delayed work
Make flush_to_ldisc properly handle parallel calls
Linus Torvalds [Wed, 14 Oct 2009 22:33:05 +0000 (15:33 -0700)]
Merge branch 'topic/x86-lds-nits' of git://git./linux/kernel/git/frob/linux-2.6-roland
* 'topic/x86-lds-nits' of git://git.kernel.org/pub/scm/linux/kernel/git/frob/linux-2.6-roland:
x86: linker script syntax nits
Linus Torvalds [Wed, 14 Oct 2009 22:31:48 +0000 (15:31 -0700)]
Merge git://git./linux/kernel/git/davem/sparc-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
watchdog: Fix rio watchdog probe function
sparc64: Set IRQF_DISABLED on LDC channel IRQs.
sparc64: Fix D-cache flushing on swapin from SW devices.
sparc64: Fix niagara2 perf IRQ bits.
Linus Torvalds [Wed, 14 Oct 2009 22:31:15 +0000 (15:31 -0700)]
Merge branch 'for-linus' of git://git390.marist.edu/linux-2.6
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
[S390] sclp_vt220 build fix
[S390] cio: change misleading console logic
[S390] call home support: fix proc handler
[S390] dasd: use idal for device characteristics
[S390] Add highgprs facility to /proc/cpuinfo
[S390] dasd: fix locking bug
[S390] tape390: Fix request queue handling in block driver
[S390] hypfs: Use subcode 6 if subcode 7 is not available
Linus Torvalds [Wed, 14 Oct 2009 22:30:45 +0000 (15:30 -0700)]
Merge branch 'sh/for-2.6.32' of git://git./linux/kernel/git/lethal/sh-2.6
* 'sh/for-2.6.32' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh: Fix a TRACE_IRQS_OFF typo.
sh: Optimize the setup_rt_frame() I-cache flush.
sh: Populate initial secondary CPU info from boot_cpu_data.
sh: Tidy up SMP cpuinfo.
sh: Use boot_cpu_data for FPU tests in sigcontext paths.
sh: ftrace: Fix up syscall tracepoint support.
sh: force dcache flush if dcache_dirty bit set.
sh: update die() output.
Linus Torvalds [Wed, 14 Oct 2009 22:25:35 +0000 (15:25 -0700)]
Merge branch 'core-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
oprofile: warn on freeing event buffer too early
oprofile: fix race condition in event_buffer free
lockdep: Use cpu_clock() for lockstat
Linus Torvalds [Wed, 14 Oct 2009 22:25:23 +0000 (15:25 -0700)]
Merge branch 'perf-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf events: Update MAINTAINERS entry file patterns
perf tools: Remove static debugfs path from parse-events
perf tools: Fix the NO_64BIT build on pure 64-bit systems
perf tools: Fix const char type propagation
Linus Torvalds [Wed, 14 Oct 2009 22:25:04 +0000 (15:25 -0700)]
Merge branch 'sched-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: Fix missing kernel-doc notation
Revert "x86, timers: Check for pending timers after (device) interrupts"
sched: Update the clock of runqueue select_task_rq() selected
Linus Torvalds [Wed, 14 Oct 2009 22:24:51 +0000 (15:24 -0700)]
Merge branch 'tracing-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
tracing/filters: Fix memory leak when setting a filter
tracing: fix trace_vprintk call
Linus Torvalds [Wed, 14 Oct 2009 22:24:32 +0000 (15:24 -0700)]
Merge branch 'x86-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86/paravirt: Use normal calling sequences for irq enable/disable
x86: fix kernel panic on 32 bits when profiling
x86: Fix Suspend to RAM freeze on Acer Aspire 1511Lmi laptop
x86, vmi: Mark VMI deprecated and schedule it for removal
Neil Brown [Tue, 15 Sep 2009 23:05:51 +0000 (16:05 -0700)]
sysfs: Allow sysfs_notify_dirent to be called from interrupt context.
sysfs_notify_dirent is a simple atomic operation that can be used to
alert user-space that new data can be read from a sysfs attribute.
Unfortunately it cannot currently be called from non-process context
because of its use of spin_lock which is sometimes taken with
interrupts enabled.
So change all lockers of sysfs_open_dirent_lock to disable interrupts,
thus making sysfs_notify_dirent safe to be called from non-process
context (as drivers/md does in md_safemode_timeout).
sysfs_get_open_dirent is (documented as being) only called from
process context, so it uses spin_lock_irq. Other places
use spin_lock_irqsave.
The usage for sysfs_notify_dirent in md_safemode_timeout was
introduced in 2.6.28, so this patch is suitable for that and more
recent kernels.
Reported-by: Joel Andres Granados <jgranado@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Cornelia Huck [Tue, 6 Oct 2009 13:33:35 +0000 (15:33 +0200)]
sysfs: Allow sysfs_move_dir(..., NULL) again.
As device_move() and kobject_move() both handle a NULL destination,
sysfs_move_dir() should do this as well (again) and fall back to
sysfs_root in that case.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Phil Carmody <ext-phil.2.carmody@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Linus Torvalds [Wed, 14 Oct 2009 16:20:41 +0000 (09:20 -0700)]
tty: use the new 'flush_delayed_work()' helper to do ldisc flush
This way all flush_to_ldisc work is always done through the workqueues,
and we thus have a single point of serialization. It also means that we
can avoid calling flush_to_ldisc() entirely if there was no delayed work
pending.
[ Side note: using workqueues and keventd as the single way to enter
flush_to_ldisc() still doesn't absolutely guarantee that we can't have
concurrency: keventd is multithreaded and has a thread per CPU, and
while the WORK_STRUCT_PENDING bit guarantees a single work only being
on the pending list once, the work might be both pending and _running_
at the same time. Workqueues are not simple. ]
This was also confirmed to fix bugzilla #14388, even without the earlier
locking fix and cleanup (commit
c8e331419: "tty: Make flush_to_ldisc()
locking more robust"). So both commits fix the same bug differently,
and either would have worked on its own. But I'm committing them both
since they are cleanups independent of each other.
Reported-and-tested-by: Boyan <btanastasov@yahoo.co.uk>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Giuseppe Cavallaro [Wed, 14 Oct 2009 22:13:45 +0000 (15:13 -0700)]
net: add support for STMicroelectronics Ethernet controllers.
This is the driver for the ST MAC 10/100/1000 on-chip Ethernet
controllers (Synopsys IP blocks).
Driver documentation:
o http://stlinux.com/drupal/kernel/network/stmmac
Revisions:
o http://stlinux.com/drupal/kernel/network/stmmac-driver-revisions
Performances:
o http://stlinux.com/drupal/benchmarks/networking/stmmac
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 14 Oct 2009 16:16:42 +0000 (09:16 -0700)]
workqueue: add 'flush_delayed_work()' to run and wait for delayed work
It basically turns a delayed work into an immediate work, and then waits
for it to finish, thus allowing you to force (and wait for) an immediate
flush of a delayed work.
We'll want to use this in the tty layer to clean up tty_flush_to_ldisc().
Acked-by: Oleg Nesterov <oleg@redhat.com>
[ Fixed to use 'del_timer_sync()' as noted by Oleg ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Randy Dunlap [Wed, 14 Oct 2009 22:10:58 +0000 (15:10 -0700)]
net: ks8851_mll uses mii interfaces
From: Randy Dunlap <randy.dunlap@oracle.com>
ks8851_mll uses mii interfaces so it needs to select MII.
ks8851_mll.c:(.text+0xf95ac): undefined reference to `generic_mii_ioctl'
ks8851_mll.c:(.text+0xf96a0): undefined reference to `mii_ethtool_gset'
ks8851_mll.c:(.text+0xf96fa): undefined reference to `mii_ethtool_sset'
ks8851_mll.c:(.text+0xf9754): undefined reference to `mii_link_ok'
ks8851_mll.c:(.text+0xf97ae): undefined reference to `mii_nway_restart'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John Bonesio [Wed, 14 Oct 2009 22:10:19 +0000 (15:10 -0700)]
net/fec_mpc52xx: Fix kernel panic on FEC error
The MDIO bus cannot be accessed at interrupt context, but on an FEC
error, the fec_mpc52xx driver reset function also tries to reset the
PHY. Since the error is detected at IRQ context, and the PHY functions
try to sleep, the kernel ends up panicking.
Resetting the PHY on an FEC error isn't even necessary. This patch
solves the problem by removing the PHY reset entirely.
Signed-off-by: John Bonesio <bones@secretlab.ca>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 14 Oct 2009 15:59:49 +0000 (08:59 -0700)]
tty: Make flush_to_ldisc() locking more robust
The locking logic in this function is extremely subtle, and it broke
when we started doing potentially concurrent 'flush_to_ldisc()' calls in
commit
e043e42bdb66885b3ac10d27a01ccb9972e2b0a3 ("pty: avoid forcing
'low_latency' tty flag").
The code in flush_to_ldisc() used to set 'tty->buf.head' to NULL, with
the intention that this would then cause any other concurrent calls to
not do anything (locking note: we have to drop the buf.lock over the
call to ->receive_buf that can block, which is why we can have
concurrency here at all in the first place).
It also used to set the TTY_FLUSHING bit, which would then cause any
concurrent 'tty_buffer_flush()' to not free all the tty buffers and
clear 'tty->buf.tail'. And with 'buf.head' being NULL, and 'buf.tail'
being non-NULL, new data would never touch 'buf.head'.
Does that sound a bit too subtle? It was. If another concurrent call to
'flush_to_ldisc()' were to come in, the NULL buf.head would indeed cause
it to not process the buffer list, but it would still clear TTY_FLUSHING
afterwards, making the buffer protection against 'tty_buffer_flush()' no
longer work.
So this clears it all up. We depend purely on TTY_FLUSHING for handling
re-entrancy, and stop playing games with the buffer list entirely. In
fact, the buffer list handling is now robust enough that we could
probably stop doing the whole "protect against 'tty_buffer_flush()'"
thing entirely.
However, Alan also points out that we would probably be better off
simplifying the locking even further, and just take the tty ldisc_mutex
around all the buffer flushing calls. That seems like a good idea, but
in the meantime this is a conceptually minimal fix (with the patch
itself being bigger than required just to clean the code up and make it
readable).
This fixes keyboard trouble under X:
http://bugzilla.kernel.org/show_bug.cgi?id=14388
Reported-and-tested-by: Frédéric Meunier <fredlwm@gmail.com>
Reported-and-tested-by: Boyan <btanastasov@yahoo.co.uk>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Paul Fulghum <paulkf@microgate.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Anton Vorontsov [Wed, 14 Oct 2009 21:54:52 +0000 (14:54 -0700)]
net: Fix OF platform drivers coldplug/hotplug when compiled as modules
Some OF platform drivers are missing module device tables, so they won't
load automatically on boot. This patch fixes the issue by adding proper
MODULE_DEVICE_TABLE() macros to the drivers.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Brian Niebuhr [Wed, 14 Oct 2009 17:04:33 +0000 (12:04 -0500)]
USB: gadget: Fix EEM driver comments and VID/PID
Remove expository comments and fix USB VID and PID
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Benjamin Herrenschmidt [Tue, 13 Oct 2009 04:53:47 +0000 (15:53 +1100)]
usb-storage: Workaround devices with bogus sense size
usb-storage: Workaround devices with bogus sense size
Some devices, such as Huawei E169, advertise more than the standard
amount of sense data, causing us to set US_FL_SANE_SENSE, assuming
they support it. However, they subsequently fail the request sense
with that size.
This works around it generically. When a sense request fails due to
a device returning an error, US_FL_SANE_SENSE was set, and that sense
request used a larger sense size, we retry with a smaller size before
giving up.
Based on an original patch by Ben Efros <ben@pc-doctor.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sarah Sharp [Fri, 9 Oct 2009 19:28:41 +0000 (12:28 -0700)]
USB: ehci: Fix IST boundary checking interval math.
When the EHCI driver falls behind in its scheduling, the active stream's
first empty microframe may be in the past with respect to the current
microframe. The code attempts to move the starting microframe ("start") N
number of microframes forward, where N is the interval of endpoint.
However, stream->interval is a copy of the endpoint's bInterval, which is
designated in frames for FS devices, and microframes for HS devices.
Convert stream->interval to microframes before using it to move the
starting microframe forward.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Huzaifa Sidhpurwala [Mon, 12 Oct 2009 09:04:45 +0000 (14:34 +0530)]
USB: option: Support for AIRPLUS MCD650 Datacard
Here is a patch for Airplus MCD 650 card
Note: This device is with Victor V Kudlak, and he confirmed that this
device works with the patch.
Signed-off-by: Huzaifa Sidhpurwala <sidhpurwala.huzaifa@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Vrabel [Mon, 12 Oct 2009 15:45:16 +0000 (15:45 +0000)]
USB: whci-hcd: always do an update after processing a halted qTD
A halted qTD always triggers a hardware list update because the qset was
either removed or reactivated.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Vrabel [Mon, 12 Oct 2009 15:45:15 +0000 (15:45 +0000)]
USB: whci-hcd: handle early deletion of endpoints
If an endpoint is deleted before it's been fully added to the hardware
list, the associated qset will not be fully initialized and an oops will
occur when complete(&qset->remove_complete) is called. This can happen
if a queued URB is cancelled.
Fix this by only removing the qset from the hardware list if the
cancelled URB had qTDs.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Stefano Panella [Mon, 12 Oct 2009 15:45:14 +0000 (15:45 +0000)]
USB: wusb: don't use the stack to read security descriptor
An urb's transfer buffer must be kmalloc'd memory and not point to the
stack or a DMA API warning results.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Vrabel [Mon, 12 Oct 2009 15:45:13 +0000 (15:45 +0000)]
USB: rename Documentation/ABI/.../sysfs-class-usb_host
The usb_host class is no more. Rename its documentation file (which
only contained WUSB specific files) to .../sysfs-class-uwb_rc-wusbhc.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Roland McGrath [Wed, 14 Oct 2009 21:16:38 +0000 (14:16 -0700)]
x86: linker script syntax nits
The linker scripts grew some use of weirdly wrong linker script syntax.
It happens to work, but it's not what the syntax is documented to be.
Clean it up to use the official syntax.
Signed-off-by: Roland McGrath <roland@redhat.com>
CC: Ian Lance Taylor <iant@google.com>
Darren Salt [Wed, 14 Oct 2009 01:19:22 +0000 (02:19 +0100)]
Staging: rt2860sta: prevent a panic when disabling when associated
This fixes a panic which is triggered when the hardware "disappears" from
beneath the driver, i.e. when wireless is toggled off via Fn-F2 on various
EeePC models.
Ref. bug report http://bugzilla.kernel.org/show_bug.cgi?id=13390
panic http://bugzilla.kernel.org/attachment.cgi?id=21928
Signed-off-by: Darren Salt <linux@youmustbejoking.demon.co.uk>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jeff Mahoney [Tue, 13 Oct 2009 00:28:11 +0000 (20:28 -0400)]
staging: more sched.h fixes
This patch contains more sched.h additions for drivers that built
fine under x86_64 but not i386 for some reason.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Cox [Mon, 12 Oct 2009 14:38:26 +0000 (15:38 +0100)]
Staging: et131x: Fix the add_10bit macro
Duh.. we need to preserve the wrap bit when adding.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Cox [Mon, 12 Oct 2009 14:38:17 +0000 (15:38 +0100)]
Staging: et131x: Correct WRAP bit handling
add_10bit loses the existing wrap value
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jeff Mahoney [Mon, 12 Oct 2009 21:10:34 +0000 (17:10 -0400)]
staging: Complete sched.h removal from interrupt.h
Commit
d43c36dc removed sched.h from interrupt.h and distributed sched.h
to users which needed it. This finishes it up for staging.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Greg Kroah-Hartman [Mon, 12 Oct 2009 22:00:08 +0000 (15:00 -0700)]
Staging: vme: fix sched.h build breakage
commit
d43c36dc removed sched.h from interrupt.h. This broke the
vme drivers. This patch fixes them.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Greg Kroah-Hartman [Mon, 12 Oct 2009 21:59:56 +0000 (14:59 -0700)]
Staging: poch: fix sched.h build breakage
commit
d43c36dc removed sched.h from interrupt.h. This broke the
poch driver. This patch fixes this.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Greg Kroah-Hartman [Mon, 12 Oct 2009 21:59:33 +0000 (14:59 -0700)]
Staging: b3dfg: fix sched.h build breakage
commit
d43c36dc removed sched.h from interrupt.h. This broke the
b3dfg driver. This patch fixes this.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Greg Kroah-Hartman [Mon, 12 Oct 2009 21:58:16 +0000 (14:58 -0700)]
Staging: comedi: fix sched.h build breakage
commit
d43c36dc removed sched.h from interrupt.h. This broke some of
the comedi drivers. This patch fixes this.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jonathan Cameron [Mon, 12 Oct 2009 18:18:09 +0000 (19:18 +0100)]
Staging: iio: Fix missing include <linux/sched.h>
linux/sched.h include was removed form linux/poll.h by
commmit
a99bbaf5ee6bad1aca0c88ea65ec6e5373e86184
Required for definition of TASK_INTERRUPTIBLE amongst others
From: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Stefan Richter [Wed, 7 Oct 2009 22:39:31 +0000 (00:39 +0200)]
firewire: sbp2: provide fallback if mgt_ORB_timeout is missing
The Unit_Characteristics entry of an SBP-2 unit directory is not
mandatory as far as I can tell. If it is missing, we would probably
fail to log in into the target because firewire-sbp2 would not wait for
status after it sent the login request.
The fix moves the cleanup of tgt->mgt_orb_timeout into a place where it
is executed exactly once before login, rather than 0..n times depending
on the target's config ROM. With targets with one or more
Unit_Characteristics entries, the result is the same as before.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Jarkko Nikula [Wed, 14 Oct 2009 16:56:35 +0000 (09:56 -0700)]
omap: McBSP: Fix incorrect receiver stop in omap_mcbsp_stop
This small typo written by author causes that McBSP receiver is disabled on
OMAP2430 and OMAP3430 even if only transmitter is stopped. This was noted
with ALSA SoC where simultaneous recording halted if playback was stopped
first.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Teerth Reddy [Wed, 14 Oct 2009 16:56:35 +0000 (09:56 -0700)]
omap: Initialization of SDRC params on Zoom2
This patch initializes the correct SDRC settings required
for DVFS on Zoom2.
Signed-off-by: Teerth Reddy <teerth@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Aaro Koskinen [Wed, 14 Oct 2009 16:56:34 +0000 (09:56 -0700)]
omap: RX-51: Drop I2C-1 speed to 2200
The I2C-1 bus frequency on RX-51 should be 2.2 MHz. The speed is limited
by TWL5030/GAIA; a higher speed could lead to errors on the interface. The
maximum speed depends on the system clock for GAIA: 2.2 MHz (if 19.2 MHz),
2.4 MHz (26 MHz) or 2.9 MHz (38.4 MHz).
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Anuj Aggarwal [Wed, 14 Oct 2009 16:56:34 +0000 (09:56 -0700)]
omap: SDMA: Fixing bug in omap_dma_set_global_params()
Argument tparams was not being used to program
global register GCR.HI_THREAD_RESERVED. This patch fixes the same.
Signed-off-by: Anuj Aggarwal <anuj.aggarwal@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Sanjeev Premi [Wed, 14 Oct 2009 16:56:33 +0000 (09:56 -0700)]
omap: CONFIG_ISP1301_OMAP redefined in Beagle defconfig
The symbol CONFIG_ISP1301_OMAP was defined twice in the
defconfig. This was causing the warning:
arch/arm/configs/omap3_beagle_defconfig:972:warning:
override: reassigning to symbol ISP1301_OMAP
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Linus Torvalds [Wed, 14 Oct 2009 16:20:41 +0000 (09:20 -0700)]
tty: use the new 'flush_delayed_work()' helper to do ldisc flush
This way all flush_to_ldisc work is always done through the workqueues,
and we thus have a single point of serialization.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Wed, 14 Oct 2009 16:16:42 +0000 (09:16 -0700)]
workqueue: add 'flush_delayed_work()' to run and wait for delayed work
It basically turns a delayed work into an immediate work, and then waits
for it to finish.
Linus Torvalds [Wed, 14 Oct 2009 15:59:49 +0000 (08:59 -0700)]
Make flush_to_ldisc properly handle parallel calls
Chris Mason [Wed, 14 Oct 2009 13:38:28 +0000 (09:38 -0400)]
Btrfs: always pin metadata in discard mode
We have an optimization in btrfs to allow blocks to be
immediately freed if they were allocated in this transaction and never
written. Otherwise they are pinned and freed when the transaction
commits.
This isn't optimal for discard mode because immediately freeing
them means immediately discarding them. It is better to give the
block to the pinning code and letting the (slow) discard happen later.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Christoph Hellwig [Wed, 14 Oct 2009 13:24:59 +0000 (09:24 -0400)]
Btrfs: enable discard support
The discard support code in btrfs currently is guarded by ifdefs for
BIO_RW_DISCARD, which is never defines as it's the name of an enum
memeber. Just remove the useless ifdefs to actually enable the code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Christoph Hellwig [Wed, 14 Oct 2009 13:24:59 +0000 (09:24 -0400)]
Btrfs: add -o discard option
Enable discard by default is not a good idea given the the trim speed
of SSD prototypes we've seen, and the carecteristics for many high-end
arrays. Turn of discards by default and require the -o discard option
to enable them on.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Yan, Zheng [Wed, 14 Oct 2009 13:24:59 +0000 (09:24 -0400)]
Btrfs: properly wait log writers during log sync
A recently fsync optimization make btrfs_sync_log skip calling
wait_for_writer in the single log writer case. This is incorrect
since the writer count can also be increased by btrfs_pin_log.
Signed-off-by: Yan Zheng <zheng.yan@oracle.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Josef Bacik [Tue, 13 Oct 2009 20:46:49 +0000 (16:46 -0400)]
Btrfs: fix possible ENOSPC problems with truncate
There's a problem where we don't do any space reservation for truncates, which
can cause you to OOPs because you will be allowed to go off in the weeds a bit
since we don't account for the delalloc bytes that are created as a result of
the truncate.
Signed-off-by: Josef Bacik <jbacik@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Li Hong [Wed, 14 Oct 2009 10:50:39 +0000 (18:50 +0800)]
x86, perf_event: Rename 'performance counter interrupt'
In '
cdd6c482c9ff9c55475ee7392ec8f672eddb7be6', we renamed
Performance Counters -> Performance Events.
The name showed up in /proc/interrupts also needs a change. I use
PMI (Performance monitoring interrupt) here, since it is the
official name used in Intel's documents.
Signed-off-by: Li Hong <lihong.hi@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <
20091014105039.GA22670@uhli>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Michael Holzheu [Wed, 14 Oct 2009 10:43:51 +0000 (12:43 +0200)]
[S390] sclp_vt220 build fix
Fix this build error:
next-
20091013 randconfig build on s390x build breaks with
drivers/s390/built-in.o:(.data+0x3354): undefined reference to `sclp_vt220_pm_event_fn'
Reported-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Signed-off-by: Michael Holzheu <michael.holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Peter Oberparleiter [Wed, 14 Oct 2009 10:43:50 +0000 (12:43 +0200)]
[S390] cio: change misleading console logic
Use cio_is_console() in io_subchannel_probe to indicate that the
special handling is console specific. As long as there is no other
subchannel for which this might be true, it is misleading to speak
of "early devices". Should more of these devices be introduced,
a cleanup of all console special handling is in order anyway.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Heiko Carstens [Wed, 14 Oct 2009 10:43:49 +0000 (12:43 +0200)]
[S390] call home support: fix proc handler
8d65af78 "sysctl: remove "struct file *" argument of ->proc_handler"
removed the struct file argument from all proc_handlers but didn't
change the call home proc handler (or call home was merged later).
So fix this now.
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Hans-Joachim Picht <hans@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Stefan Haberland [Wed, 14 Oct 2009 10:43:48 +0000 (12:43 +0200)]
[S390] dasd: use idal for device characteristics
If the rdc_buffer is above 2G we need indirect addresssing so we have
to use an idaw to give the rdc_buffer to the ccw.
If the rdc_buffer is under 2G nothing changes.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Andreas Krebbel [Wed, 14 Oct 2009 10:43:47 +0000 (12:43 +0200)]
[S390] Add highgprs facility to /proc/cpuinfo
This patch makes the hwcap bit for the high gprs feature to be visible
in /proc/cpuinfo.
Signed-off-by: Andreas Krebbel <Andreas.Krebbel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Stefan Haberland [Wed, 14 Oct 2009 10:43:46 +0000 (12:43 +0200)]
[S390] dasd: fix locking bug
Replace spin_lock with spin_lock_irqsave in dasd_eckd_restore_device.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Michael Holzheu [Wed, 14 Oct 2009 10:43:45 +0000 (12:43 +0200)]
[S390] tape390: Fix request queue handling in block driver
When setting a channel attached tape online under Linux 2.6.31, the
"vol_id" process from udev hangs in sync_page():
2 sync_page+144 [0x1dfaac]
3 __wait_on_bit_lock+194 [0x58c23e]
4 __lock_page+116 [0x1df9dc]
5 truncate_inode_pages_range+728 [0x1ed7cc]
6 __blkdev_put+244 [0x25f738]
7 __fput+300 [0x229c4c]
8 filp_close+122 [0x225a3a]
The reason for that is an error in the request queue handling. It can
happen that we fetch a request, but do not process it further because
the number of queued requests exceeds TAPEBLOCK_MIN_REQUEUE.
To fix this, we should call blk_peek_request() instead of
blk_fetch_request() in the while condition and fetch the request in
the loop body afterwards.
This bug was introduced with the patch "block: implement and enforce
request peek/start/fetch" (
9934c8c04561413609d2bc38c6b9f268cba774a4)
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Michael Holzheu [Wed, 14 Oct 2009 10:43:44 +0000 (12:43 +0200)]
[S390] hypfs: Use subcode 6 if subcode 7 is not available
Hypfs never worked on systems that only provide D204 subcode 6.
In these cases we nevertheless used subcode 7. With this fix, we
use subcode 6, if it is available and the system does not provide
subcode 7.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
projects / openwrt / staging / blogic.git / log