John Crispin [Sun, 30 Mar 2014 10:02:30 +0000 (10:02 +0000)]
lntiq: add support for Astoria ARV7519RW.
These patches add support for the Astoria ARV7519RW aka Livebox 2.1
The PCI and PCIe interfaces have been disabled. Also, because there are
two revisions of this board with different GPHY firmwares, two targets
were defined.
V2: rewrote partitions to work with an u-boot specifically made for
these boards.
Signed off by: Esteban Benito <estebanjbs@gmail.com>
Signed off by: Carles Gadea <carlesgrg@gmail.com>
Tested by: José Vázquez Fernández <ppvazquezfer@gmail.com>
SVN-Revision: 40329
John Crispin [Sun, 30 Mar 2014 09:16:52 +0000 (09:16 +0000)]
lantiq: do an endianness swap to the RT2860 eeprom for ARV752DPW(22)
ARV7510PW22, ARV752DPW and ARV752DPW22 have the RT2860 eeprom stored in
flash as big-endian, but the driver needs it in little-endian format. We
have to swab it before handing it over. This requires my earlier patch
for busybox.
Funnily enough, ARV752DPW works also with the incorrect eeprom, but
undoubtedly unoptimally. I have a hunch that also the final remaining
Lantiq board would require this swabbing, but I'm not sure, so I just
swab it in the three boards that I know about.
v2:
* Swab also on ARV7510PW22 based on feedback from Alvaro Rojas
* Fix the offset with bs=2
Signed-off-by: Matti Laakso <malaakso at elisanet.fi>
SVN-Revision: 40328
John Crispin [Sun, 30 Mar 2014 09:16:47 +0000 (09:16 +0000)]
busybox: backport dd conv=swab from 1.22
Some boards have the WLAN EEPROM stored in flash in big-endian format,
whereas the driver requires the EEPROM in little-endian format. The
conv=swab option in dd is particularly useful in this case. This patch
backports this feature from busybox-1.22 based on the following commits:
commit
b941316ae5313be523b64f0a9151ee4decb2b35b dd: support conv=swab
commit
8395bd3f52f8ed46fa3ffc316b2d113afa748bae dd: fix example in a
comment. No code changes.
commit
5b9910f0a4a1b7976c46e6f849aaa263180e5521 dd: fail if swab is
attempted on odd-sized block
commit
0ff0b320a2dbb5e0b5fa245ffd9b2648d7026843 dd: code shrink
v2: include the commit messages from upstream
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 40327
John Crispin [Sun, 30 Mar 2014 09:16:43 +0000 (09:16 +0000)]
lantiq: add esi
http://patchwork.openwrt.org/patch/3703/
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 40326
John Crispin [Sun, 30 Mar 2014 09:16:39 +0000 (09:16 +0000)]
ltq-adsl-mei: improve memory allocation
The ltq-adsl-mei driver allocates memory for the ADSL firmware in a
rather stupid way, leading to several 128k allocations, which fail when
many services are enabled. This patch tries to allocate 64 kiB chunks,
and only falls back to larger allocations if the returned pointers are
not correctly aligned. Fixes out-of-memory errors on Danube boards with
32 MiB RAM.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 40325
John Crispin [Sun, 30 Mar 2014 09:16:35 +0000 (09:16 +0000)]
lantiq: fix mtd_split for brnboot firmware images
The existing code only tries to split a parition with name "rootfs"
while actually looking for kernel+rootfs, where usually "firmware" is
used as a partition name. This doesn't make sense, as even if there
was a partition 'rootfs' given by mtdparts or via device-tree, this
code would lead to another partition called 'rootfs' being created
which would not be properly distinguished in the current user-space
code.
While potentially we could use CONFIG_MTD_SPLIT_FIRMWARE_NAME to make
that configurable, the lack of users of brnboot and the fact that we
can freely decide the partition name made me simply change the
hard-coded string constant from "rootfs" to "firmware".
(I'm going to add support for ARV7506PW which run brnboot and needs
this change)
SVN-Revision: 40324
John Crispin [Sun, 30 Mar 2014 09:16:31 +0000 (09:16 +0000)]
lantiq: fixup ath5k support
http://patchwork.openwrt.org/patch/4417/
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 40323
John Crispin [Sun, 30 Mar 2014 09:16:27 +0000 (09:16 +0000)]
ltq-vdsl: add led status reporting
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 40322
John Crispin [Sun, 30 Mar 2014 09:16:23 +0000 (09:16 +0000)]
lantiq: fix initial VLAN conf for P2601HNFX
Signed-off-by: Antonios Vamporakis <ant@area128.com>
SVN-Revision: 40321
John Crispin [Sun, 30 Mar 2014 09:16:19 +0000 (09:16 +0000)]
lantiq: P2601HNFX dts update for STP and buttons
- Set correct AltSel for STP pins
- Set front button to rfkill
Signed-off-by: Antonios Vamporakis <ant@area128.com>
SVN-Revision: 40320
John Crispin [Sun, 30 Mar 2014 09:16:15 +0000 (09:16 +0000)]
lantiq: add support for Arcadyan ARV7519PW
This patch adds almost full support for this board.
- WiFi is still not working
- USB will not power up. According to some reports, it may be a passive port
Signed-off-by: Antonios Vamporakis <ant@area128.com>
SVN-Revision: 40319
John Crispin [Sun, 30 Mar 2014 09:16:10 +0000 (09:16 +0000)]
lantiq: reset gphys on reboot
If gphys are not reset upstream uboot can not use them anymore.
Signed-off-by: Antonios Vamporakis <ant@area128.com>
SVN-Revision: 40318
John Crispin [Sun, 30 Mar 2014 09:16:06 +0000 (09:16 +0000)]
lantiq: add support for ZyXEL P2812HNUFX
This patch adds almost full support for this board. WiFi is still not working.
The FXS ports are not functional due to missing support for the TAPI driver on
VR9 SoC.
Signed-off-by: Antonios Vamporakis <ant@area128.com>
Tested-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 40317
John Crispin [Sun, 30 Mar 2014 09:16:02 +0000 (09:16 +0000)]
lantiq: add ubifs support in image Makefile
Signed-off-by: Antonios Vamporakis <ant@area128.com>
SVN-Revision: 40316
John Crispin [Sun, 30 Mar 2014 09:15:58 +0000 (09:15 +0000)]
lantiq: add ubifs to FEATURES
Signed-off-by: Antonios Vamporakis <ant@area128.com>
SVN-Revision: 40315
John Crispin [Sun, 30 Mar 2014 09:15:54 +0000 (09:15 +0000)]
lantiq: xrx200: add ubi support in the kernel
Signed-off-by: Antonios Vamporakis <ant@area128.com>
SVN-Revision: 40314
John Crispin [Sun, 30 Mar 2014 09:15:50 +0000 (09:15 +0000)]
lantiq: add inital support for xrx200 switch
Signed-off-by: Antonios Vamporakis <ant@area128.com>
SVN-Revision: 40313
John Crispin [Sun, 30 Mar 2014 09:15:46 +0000 (09:15 +0000)]
lantiq: xrx200: fix duplex
Both the GPL driver from ZyXEL and the xrx200 driver have this error. The flags
are reversed. Full duplex is marked as half and the other way around. With this
fix the switch will push full GBit speeds.
Signed-off-by: Antonios Vamporakis <ant@area128.com>
SVN-Revision: 40312
John Crispin [Sun, 30 Mar 2014 09:15:41 +0000 (09:15 +0000)]
lantiq: fixup 3370 dts file
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 40311
John Crispin [Sun, 30 Mar 2014 09:15:37 +0000 (09:15 +0000)]
lantiq: fix nand/ebu locking
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 40310
John Crispin [Sun, 30 Mar 2014 09:15:33 +0000 (09:15 +0000)]
lantiq: add tffs driver
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 40309
John Crispin [Sun, 30 Mar 2014 09:15:29 +0000 (09:15 +0000)]
ltq-vdsl: fix MIPS16 compile breakage
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 40308
John Crispin [Sun, 30 Mar 2014 09:15:25 +0000 (09:15 +0000)]
firmware: create a new folder for holfing firmware blobs
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 40307
John Crispin [Sun, 30 Mar 2014 09:15:20 +0000 (09:15 +0000)]
kernel: export gluebi info to sysfs
Export the ubi_num and vol_id into the sysfs record of the gluebi-
emulated mtd device. Previously userspace didn't have a way to
map gluebi-emulated devices back to their corresponding ubi volumes.
SVN-Revision: 40306
John Crispin [Sun, 30 Mar 2014 09:15:16 +0000 (09:15 +0000)]
kernel: rtl8306: fix vlan support on lantiq ar9 p2601hnfx
If the CPU port is not forced up, the link, at least on this board, is lost after
changes are applied. This makes sure that the link is restored. Regression tests
should confirm it doesn't break other boards.
Signed-off-by: Antonios Vamporakis <ant@area128.com>
SVN-Revision: 40305
John Crispin [Sun, 30 Mar 2014 09:15:11 +0000 (09:15 +0000)]
kernel: rtl8306: fix max pvid & remove port isolation
- hide port pvid - vlan index relation
- switch initialises with vlans disabled so port isolation is not used
- remove special treatment of cpu port
Signed-off-by: Antonios Vamporakis <ant@area128.com>
SVN-Revision: 40304
John Crispin [Sun, 30 Mar 2014 09:15:07 +0000 (09:15 +0000)]
kernel: rtl8306: cosmetic changes for swconfig
Changes to:
- show the correct "enable_vlan" value under "Global attributes"
- show tagged ports under "Vlan: ports"
- use get_port_link method to report link status
Signed-off-by: Antonios Vamporakis <ant@area128.com>
SVN-Revision: 40303
John Crispin [Sun, 30 Mar 2014 09:15:03 +0000 (09:15 +0000)]
util-linux: backport upstream fix for unshare utility
the unshare utility wasn't getting certain defines for mount
anymore.
SVN-Revision: 40302
John Crispin [Sun, 30 Mar 2014 09:14:58 +0000 (09:14 +0000)]
mtd: improve mtd detection
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 40301
Felix Fietkau [Sat, 29 Mar 2014 17:10:52 +0000 (17:10 +0000)]
dropbear: move options.h editing to Build/Configure
fixes incremental build with change to CONFIG_DROPBEAR_ECC
drop --with-shared which is unknown to configure
Patch by Catalin Patulea <cat@vv.carleton.ca>
SVN-Revision: 40300
Felix Fietkau [Sat, 29 Mar 2014 17:05:35 +0000 (17:05 +0000)]
dropbear: add options SSHKeepAlive and IdleTimeout.
Without timeout mechanism, if ssh client disconnected without sending
FIN or RST, forked dropbear servers would hang there for
KEX_RETRY_TIMEOUT seconds (8 hours).
TCP keepalive is not implemented in dropbear yet, thus the name
SSHKeepAlive.
300 seconds in this patch is selected from the default value of
ServerAliveInterval for Debian ssh client (See man ssh_config).
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
SVN-Revision: 40299
Felix Fietkau [Sat, 29 Mar 2014 16:59:33 +0000 (16:59 +0000)]
dropbear: fix interface config setting
Patch from #15070
SVN-Revision: 40298
Felix Fietkau [Sat, 29 Mar 2014 16:59:26 +0000 (16:59 +0000)]
dropbear: update to 2014.63
Upstream changelog:
https://matt.ucc.asn.au/dropbear/CHANGES
This adds elliptic curve cryptography (ECC) support as an option, disabled
by default.
dropbear mips 34kc uClibc binary size:
before: 161,672 bytes
after, without ECC (default): 164,968
after, with ECC: 198,008
Signed-off-by: Catalin Patulea <cat@vv.carleton.ca>
SVN-Revision: 40297
Jo-Philipp Wich [Fri, 28 Mar 2014 16:05:46 +0000 (16:05 +0000)]
mac80211: skip antenna gain when compiling regdb.txt (#15397)
The antenna gain attribute has been removed from the upstream regulatory database.
Incorperate patch from Luis R. Rodriguez to skip the parsing of the gain attribute
in genregdb.awk in order to emit proper rules again.
Also refresh fuzzy patches while we're at it.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 40296
John Crispin [Thu, 27 Mar 2014 13:36:01 +0000 (13:36 +0000)]
ubox: fix logd (hopefully)
https://dev.openwrt.org/ticket/15357
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 40295
John Crispin [Thu, 27 Mar 2014 13:34:56 +0000 (13:34 +0000)]
lantiq: drop old svip folders
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 40294
Imre Kaloz [Thu, 27 Mar 2014 11:28:51 +0000 (11:28 +0000)]
update regulatory database to 2013-11-27
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 40293
Gabor Juhos [Thu, 27 Mar 2014 09:28:33 +0000 (09:28 +0000)]
kernel: update 3.10 to 3.10.34
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40291
Gabor Juhos [Thu, 27 Mar 2014 06:36:59 +0000 (06:36 +0000)]
ar71xx: build image for TL-WDR4300v1 (IL)
The version of TL-WDR4300 sold in Israel comes with a different
hardware id.
Patch-by: Daniel <daniel@makrotopia.org>
Patchwork: http://patchwork.openwrt.org/patch/5001/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40038
Gabor Juhos [Thu, 27 Mar 2014 06:36:58 +0000 (06:36 +0000)]
firmware-utils/mktplinkfw: add support for TL-WDR4300v1 (IL)
The version of TL-WDR4300 sold in Israel comes with a different
hardware id.
Patch-by: Daniel <daniel@makrotopia.org>
Patchwork: http://patchwork.openwrt.org/patch/5001/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40037
Gabor Juhos [Thu, 27 Mar 2014 06:36:57 +0000 (06:36 +0000)]
ar71xx: add profile and build firmware image for the Oolite v1 board
Patch-by: Lars Bøgild Thomsen <lth@cow.dk>
Patchwork: http://patchwork.openwrt.org/patch/4922/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40036
Gabor Juhos [Thu, 27 Mar 2014 06:36:49 +0000 (06:36 +0000)]
firmware-utils/mktplinkfw: add support for the Oolite v1 board
Patch-by: Lars Bøgild Thomsen <lth@cow.dk>
Patchwork: http://patchwork.openwrt.org/patch/4922/
[juhosg: fix whitespaces]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40035
Gabor Juhos [Thu, 27 Mar 2014 06:36:48 +0000 (06:36 +0000)]
firmware-utils/mktplinkfw: add an option to generate 16MiB images
Signed-off-by: Andrew 'Necromant' Andrianov <andrew@ncrmnt.org>
Patchwork: http://patchwork.openwrt.org/patch/2449/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40034
Gabor Juhos [Thu, 27 Mar 2014 06:36:47 +0000 (06:36 +0000)]
ar71xx: add user space support for the Oolite v1 board
Patch-by: Lars Bøgild Thomsen <lth@cow.dk>
Patchwork: http://patchwork.openwrt.org/patch/4922/
[juhosg: use correct board name in uci-defaults/02_network]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40033
Gabor Juhos [Thu, 27 Mar 2014 06:36:46 +0000 (06:36 +0000)]
ar71xx: add kernel support for the Oolite v1 board
Patch-by: Lars Bøgild Thomsen <lth@cow.dk>
Patchwork: http://patchwork.openwrt.org/patch/4922/
[juhosg:
- use a separate patch for kernel changes,
- reorder Kconfig and Makefile entries,
- change function and variable names to be lowercase only
and fix misaligned tabs in mach-gs-oolite.c,
... ]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40032
Gabor Juhos [Thu, 27 Mar 2014 06:35:55 +0000 (06:35 +0000)]
ar71xx: rename RB951Ui specific kernel patch
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40031
Felix Fietkau [Wed, 26 Mar 2014 19:26:32 +0000 (19:26 +0000)]
feeds.conf.default: fix copy&paste mistake (#15383)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 40030
Felix Fietkau [Wed, 26 Mar 2014 16:08:09 +0000 (16:08 +0000)]
feeds: switch to using http(s) urls
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 40028
Felix Fietkau [Wed, 26 Mar 2014 16:08:06 +0000 (16:08 +0000)]
usbmode: switch to http:// instead of git://
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 40027
Felix Fietkau [Wed, 26 Mar 2014 16:08:02 +0000 (16:08 +0000)]
jsonpath: switch to http:// instead of git://
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 40026
Felix Fietkau [Wed, 26 Mar 2014 16:07:58 +0000 (16:07 +0000)]
libubox: switch to git.openwrt.org as source
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 40025
Imre Kaloz [Wed, 26 Mar 2014 14:14:20 +0000 (14:14 +0000)]
update to 3.14-rc8
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 40023
Imre Kaloz [Wed, 26 Mar 2014 11:34:39 +0000 (11:34 +0000)]
upgrade 3.13 targets to 3.13.7
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 40022
Felix Fietkau [Wed, 26 Mar 2014 10:50:09 +0000 (10:50 +0000)]
mtd: add support for bad blocks in NAND flash
NAND flash is very likely to contain bad blocks.
Currently, mtd and therefore sysupgrade fails when it encounters a single bad block, potentially leaving an unbootable system.
This patch allows the mtd utility to skip bad blocks in NAND flash and complete sysupgrade successfully.
Patch by: Matthew Redfearn <matt.redfearn@nxp.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 40021
Steven Barth [Wed, 26 Mar 2014 10:12:49 +0000 (10:12 +0000)]
6rd / ds-lite: make the firewall-zones of nested-protocols configurable
SVN-Revision: 40020
Steven Barth [Wed, 26 Mar 2014 09:48:20 +0000 (09:48 +0000)]
dhcp: send 6rd-ORO when expecting 6rd-information
SVN-Revision: 40019
John Crispin [Tue, 25 Mar 2014 20:15:50 +0000 (20:15 +0000)]
fs-tools: add back mount_root, jffs2reset and ffs2mark functionality
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 40018
Felix Fietkau [Tue, 25 Mar 2014 15:06:24 +0000 (15:06 +0000)]
ustream-ssl: update to latest version, adds certificate validation support
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 40017
Imre Kaloz [Tue, 25 Mar 2014 14:56:35 +0000 (14:56 +0000)]
add the TI AM335x PM firmware package
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 40016
Luka Perkov [Mon, 24 Mar 2014 00:19:44 +0000 (00:19 +0000)]
util-linux: update to 2.24.1
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 40010
Luka Perkov [Mon, 24 Mar 2014 00:19:33 +0000 (00:19 +0000)]
uClibc: backport mount.h update
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 40009
Luka Perkov [Sun, 23 Mar 2014 16:08:58 +0000 (16:08 +0000)]
libroxml: enable xpath support
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 40008
Felix Fietkau [Sun, 23 Mar 2014 11:59:37 +0000 (11:59 +0000)]
ca-certificates: install to /etc/ssl/certs/ directly instead of installing a symlink (fixes #15351)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 40007
Felix Fietkau [Sat, 22 Mar 2014 19:52:48 +0000 (19:52 +0000)]
partially revert "build: remove check for nonexistant CONFIG_TAR_VERBOSITY variable and move TAR_OPTIONS to unpack.mk"
This complicates the evaluation order for some packages
SVN-Revision: 40006
Felix Fietkau [Sat, 22 Mar 2014 19:38:48 +0000 (19:38 +0000)]
uhttpd: update to latest version, improves cgi path handling
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 40005
Felix Fietkau [Fri, 21 Mar 2014 23:39:47 +0000 (23:39 +0000)]
ustream-ssl: update to the latest version, fixes cyassl build
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 40004
Felix Fietkau [Fri, 21 Mar 2014 20:49:56 +0000 (20:49 +0000)]
uhttpd: update to latest version, fixes HEAD requests to CGI scripts
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 40003
John Crispin [Fri, 21 Mar 2014 18:55:31 +0000 (18:55 +0000)]
include: r39979 broke kernel unpacking
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 40002
Felix Fietkau [Fri, 21 Mar 2014 15:55:27 +0000 (15:55 +0000)]
netifd: update to the latest version, adds support for reloading proto handlers on toplogy changes
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 40001
Felix Fietkau [Fri, 21 Mar 2014 15:55:23 +0000 (15:55 +0000)]
px5g: rename the old package to px5g-standalone, add a new one that links against polarssl
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 40000
Felix Fietkau [Fri, 21 Mar 2014 15:55:18 +0000 (15:55 +0000)]
polarssl: add support for generating rsa keys
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 39999
Felix Fietkau [Fri, 21 Mar 2014 15:55:15 +0000 (15:55 +0000)]
libroxml: add package (tiny XML parser/writer library)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 39998
Felix Fietkau [Fri, 21 Mar 2014 15:55:11 +0000 (15:55 +0000)]
x86_64: fix sysupgrade
Function move_config should be called after or during preinit_mount_root
hook in do_mount_root function. At this state sysupgrade.tgz is not in its
place during that time when do_mount_root is called. Function move_config
is called later so the sysupgrade.tgz stays in root directory to the second
restart when it is unpacked properly.
This patch adds move_config function to preinit_mount_root hook instead
of preinit_main and changes the filename of script to be called before
80_mount_root is called. It will prepare the sysupgrade archive for do_mount_root
within preinit_mount_root hook.
This issue was introduced for target x86. Since the target for x86_64 is
similar to x86, this issue is present also in this target. It solves the
ticket #15042 and #14088.
Signed-off-by: Jiri Slachta <slachta@cesnet.cz>
Tested-By: Stefan Hellermann <stefan@the2masters.de>
SVN-Revision: 39997
Felix Fietkau [Fri, 21 Mar 2014 15:55:07 +0000 (15:55 +0000)]
x86: fix sysupgrade
Function move_config should be called after or during preinit_mount_root
hook in do_mount_root function. At this state sysupgrade.tgz is not in its
place during that time when do_mount_root is called. Function move_config
is called later so the sysupgrade.tgz stays in root directory to the second
restart when it is unpacked properly.
This patch adds move_config function to preinit_mount_root hook instead
of preinit_main and changes the filename of script to be called before
80_mount_root is called. It will prepare the sysupgrade archive for do_mount_root
within preinit_mount_root hook.
This patch solves ticket #15042 and #14088.
Signed-off-by: Jiri Slachta <slachta@cesnet.cz>
SVN-Revision: 39996
Felix Fietkau [Fri, 21 Mar 2014 15:55:03 +0000 (15:55 +0000)]
hostapd: add pbc_in_m1 option
Option pbc_in_m1 is being used as a WPS capability discovery
workaround for PBC with Windows 7.
Add possibility to enable this workaround from UCI.
To enable it, turn on wps and set wps_pbc_in_m1 parameter to 1.
Signed-off-by: Pawel Kulakowski <pawel.kulakowski@tieto.com>
SVN-Revision: 39995
Felix Fietkau [Fri, 21 Mar 2014 15:54:59 +0000 (15:54 +0000)]
ead: clean up
Remove unused variables
Correct some (non important) memory leaks
Remove fclose(NULL)
Correct possible out of bound access
spotted with cppcheck
Signed-off-by: Etienne CHAMPETIER <etienne.champetier@free.fr>
SVN-Revision: 39994
Felix Fietkau [Fri, 21 Mar 2014 15:54:56 +0000 (15:54 +0000)]
ead: set_nonblock() is doing nothing (typo)
spotted with cppcheck
Signed-off-by: Etienne CHAMPETIER <etienne.champetier@free.fr>
SVN-Revision: 39993
Felix Fietkau [Fri, 21 Mar 2014 15:54:52 +0000 (15:54 +0000)]
ppp: remove ppp requirement from chat
This patch removes dependancy of PPP from chat application as chat application can be used for other serial communication as well that is not dependant on PPP and therefore one should be able to install chat without PPP. There also are no dependencies within chat application for PPP.
Signed-off-by: Oskari Rauta <oskari.rauta at gmail.com>
SVN-Revision: 39992
Felix Fietkau [Fri, 21 Mar 2014 15:54:48 +0000 (15:54 +0000)]
libnl-tiny: ensure compatibility to libnl version 3 and higher
To be prepared to support keepalived 1.2.10 and higher we need libnl3 or
higher. The attached patch
add some defines so that it can be build be libnl-tiny.
Patch by Thomas Heil
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 39991
Felix Fietkau [Fri, 21 Mar 2014 15:54:44 +0000 (15:54 +0000)]
Add Bosch C_CAN/D_CAN modules kernel package
Add Bosch C_CAN/D_CAN driver as a kernel package. The D_CAN controller is used
on BeagleBoneBlack.
Signed-off-by: Jan Kardell <jan.kardell@telliq.com>
SVN-Revision: 39990
Felix Fietkau [Fri, 21 Mar 2014 15:54:41 +0000 (15:54 +0000)]
kernel: add can.ko to the kmod-can package.
Build all of the can support as modules, otherwise the kernel image is
changed when a can kernel package is selected, because the can protocol
is then built in into the kernel image.
Signed-off-by: Jan Kardell <jan.kardell@telliq.com>
SVN-Revision: 39989
Felix Fietkau [Fri, 21 Mar 2014 15:54:37 +0000 (15:54 +0000)]
mac80211: iwlagn include firmware for 7260 cards
This patch enables including the firmware for Intel Dual Band Wireless-N 7260 and Intel Dual Band Wireless-AC 7260 cards in iwlagn.
Signed-off-by: Matthew Reeve <mreeve@tenxnetworks.com>
SVN-Revision: 39988
Felix Fietkau [Fri, 21 Mar 2014 15:54:34 +0000 (15:54 +0000)]
busybox: remove obsolete brctl linux 2.4 compat patch
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 39987
Felix Fietkau [Fri, 21 Mar 2014 15:54:30 +0000 (15:54 +0000)]
busybox: remove obsolete awk include() patch
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 39986
Felix Fietkau [Fri, 21 Mar 2014 15:54:26 +0000 (15:54 +0000)]
ustream-ssl: update to latest version, fixes writes before ssl handshake completion
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 39985
Felix Fietkau [Fri, 21 Mar 2014 15:54:22 +0000 (15:54 +0000)]
ca-certificates: add system CA certificates package (based on the debian one)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 39984
Felix Fietkau [Fri, 21 Mar 2014 15:54:18 +0000 (15:54 +0000)]
procd: add a PROCD_DEBUG variable that will dump the ubus calls from init scripts to stderr
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 39983
Felix Fietkau [Fri, 21 Mar 2014 15:54:14 +0000 (15:54 +0000)]
build: remove GREP_OPTIONS export from rules.mk, defining it in the top-level Makefile is enough
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 39982
Felix Fietkau [Fri, 21 Mar 2014 15:54:11 +0000 (15:54 +0000)]
build: remove duplicate variable definitions
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 39981
Felix Fietkau [Fri, 21 Mar 2014 15:54:07 +0000 (15:54 +0000)]
build: remove check to nonexistant CONFIG_ENABLE_LOCALE variable and move DISABLE_NLS to package-defaults.mk
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 39980
Felix Fietkau [Fri, 21 Mar 2014 15:54:03 +0000 (15:54 +0000)]
build: remove check for nonexistant CONFIG_TAR_VERBOSITY variable and move TAR_OPTIONS to unpack.mk
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 39979
Felix Fietkau [Fri, 21 Mar 2014 15:03:08 +0000 (15:03 +0000)]
mac80211: Enable kmod-rt2800-soc package for rt288x target
Trunk and the latest backport to Attitude Adjustment have the
kmod-rt2800-soc package hidden for the ramips_rt288x target.
This makes the dependency match the dependency given in the
TITLE field.
Signed-off-by: Claudio Leite <leitec@staticky.com>
SVN-Revision: 39976
Florian Fainelli [Thu, 20 Mar 2014 23:16:06 +0000 (23:16 +0000)]
libusb-compat: install libusb-config in host staging dir
A bunch of packages such as sispctl look for libusb-config to find it, install
libusb-config in staging_dir/*/host/bin which is in the TARGET_PATH.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 39975
Florian Fainelli [Thu, 20 Mar 2014 23:15:56 +0000 (23:15 +0000)]
modules: make kmod-pcspkr depend on X86
The kernel Kconfig dependency lists X86, and we will fail building this module
on other platforms such as Malta.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 39974
Zoltan Herpai [Thu, 20 Mar 2014 22:46:18 +0000 (22:46 +0000)]
sunxi: init eth0 as lan instead of wan, add a couple boards
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
SVN-Revision: 39973
Zoltan Herpai [Thu, 20 Mar 2014 21:59:52 +0000 (21:59 +0000)]
sunxi: enable /proc/device-tree - used for board detection
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
SVN-Revision: 39972
Zoltan Herpai [Thu, 20 Mar 2014 21:40:07 +0000 (21:40 +0000)]
sunxi: various changes - fix mmc, sata, usb (partially) on CubieTruck - fix hstimer DT on A20
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Signed-off-by: Zalan Blenessy <zalan.blenessy@gmail.com>
SVN-Revision: 39971
Felix Fietkau [Thu, 20 Mar 2014 20:06:59 +0000 (20:06 +0000)]
netifd: update to the latest version, fixes ubus handling of proto data items
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 39970
Felix Fietkau [Thu, 20 Mar 2014 14:14:34 +0000 (14:14 +0000)]
toolchain: remove accidental leftover debug code
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 39969
Felix Fietkau [Thu, 20 Mar 2014 14:14:30 +0000 (14:14 +0000)]
busybox: fix existing "export -n" in ash
Minor fix to existing patch which did not correctly implement -n support for the export command in ash. The VEXPORT flag of a variable was set in the first call to setvareq() and then remained set in the subsequent call, because the variable already existed in the environment.
Although /lib/functions.sh by default does not export variables (NO_EXPORT=1), this issue was leading to dirty environments.
Without this fix:
(ash) export A=1; export -n B=2; /bin/ash -c "echo \$A, \$B"
1, 2
With this fix:
(ash) export A=1; export -n B=2; /bin/ash -c "echo \$A, \$B"
1,
Signed-off-by: Christophe Lermytte <openwrt@lermytte.be>
SVN-Revision: 39968
projects / openwrt / staging / dangole.git / log