Noralf Trønnes [Mon, 3 Oct 2016 20:06:13 +0000 (22:06 +0200)]
i2c: bcm2835: Support i2c-dev ioctl I2C_TIMEOUT
Use i2c_adapter->timeout for the completion timeout value. The core
default is 1 second.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Noralf Trønnes [Mon, 3 Oct 2016 20:06:12 +0000 (22:06 +0200)]
i2c: bcm2835: Add support for Repeated Start Condition
Documentation/i2c/i2c-protocol states that Combined transactions should
separate messages with a Start bit and end the whole transaction with a
Stop bit. This patch adds support for issuing only a Start between
messages instead of a Stop followed by a Start.
This implementation differs from downstream i2c-bcm2708 in 2 respects:
- it uses an interrupt to detect that the transfer is active instead
of using polling. There is no interrupt for Transfer Active, but by
not prefilling the FIFO it's possible to use the TXW interrupt.
- when resetting/disabling the controller between transfers it writes
CLEAR to the control register instead of just zero.
Using just zero gave many errors. This might be the reason why
downstream had to disable this feature and make it available with a
module parameter.
I have run thousands of transfers to a DS1307 (rtc), MMA8451 (accel)
and AT24C32 (eeprom) in parallel without problems.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Noralf Trønnes [Mon, 3 Oct 2016 20:06:11 +0000 (22:06 +0200)]
i2c: bcm2835: Can't support I2C_M_IGNORE_NAK
The controller can't support this flag, so remove it.
Documentation/i2c/i2c-protocol states that all of the message is sent:
I2C_M_IGNORE_NAK:
Normally message is interrupted immediately if there is [NA] from the
client. Setting this flag treats any [NA] as [A], and all of
message is sent.
>From the BCM2835 ARM Peripherals datasheet:
The ERR field is set when the slave fails to acknowledge either
its address or a data byte written to it.
So when the controller doesn't receive an ack, it sets ERR and raises
an interrupt. In other words, the whole message is not sent.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Noralf Trønnes [Mon, 3 Oct 2016 20:06:10 +0000 (22:06 +0200)]
i2c: bcm2835: Use dev_dbg logging on transfer errors
Writing to an AT24C32 generates on average 2x i2c transfer errors per
32-byte page write. Which amounts to a lot for a 4k write. This is due
to the fact that the chip doesn't respond during it's internal write
cycle when the at24 driver tries and retries the next write.
Only a handful drivers use dev_err() on transfer error, so switch to
dev_dbg() instead.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Noralf Trønnes [Mon, 3 Oct 2016 20:06:09 +0000 (22:06 +0200)]
i2c: bcm2835: Protect against unexpected TXW/RXR interrupts
If an unexpected TXW or RXR interrupt occurs (msg_buf_remaining == 0),
the driver has no way to fill/drain the FIFO to stop the interrupts.
In this case the controller has to be disabled and the transfer
completed to avoid hang.
(CLKT | ERR) and DONE interrupts are completed in their own paths, and
the controller is disabled in the transfer function after completion.
Unite the code paths and do disabling inside the interrupt routine.
Clear interrupt status bits in the united completion path instead of
trying to do it on every interrupt which isn't necessary.
Only CLKT, ERR and DONE can be cleared that way.
Add the status value to the error value in case of TXW/RXR errors to
distinguish them from the other S_LEN error.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Noralf Trønnes [Mon, 3 Oct 2016 20:06:08 +0000 (22:06 +0200)]
i2c: bcm2835: Fix hang for writing messages larger than 16 bytes
Writing messages larger than the FIFO size results in a hang, rendering
the machine unusable. This is because the RXD status flag is set on the
first interrupt which results in bcm2835_drain_rxfifo() stealing bytes
from the buffer. The controller continues to trigger interrupts waiting
for the missing bytes, but bcm2835_fill_txfifo() has none to give.
In this situation wait_for_completion_timeout() apparently is unable to
stop the madness.
The BCM2835 ARM Peripherals datasheet has this to say about the flags:
TXD: is set when the FIFO has space for at least one byte of data.
RXD: is set when the FIFO contains at least one byte of data.
TXW: is set during a write transfer and the FIFO is less than full.
RXR: is set during a read transfer and the FIFO is or more full.
Implementing the logic from the downstream i2c-bcm2708 driver solved
the hang problem.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Linus Torvalds [Sat, 5 Nov 2016 23:23:36 +0000 (16:23 -0700)]
Linux 4.9-rc4
Linus Torvalds [Sat, 5 Nov 2016 22:30:12 +0000 (15:30 -0700)]
Merge branch 'i2c/for-current' of git://git./linux/kernel/git/wsa/linux
Pull i2c fix from Wolfram Sang:
"A bugfix for the I2C core fixing a (rare) race condition"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: core: fix NULL pointer dereference under race condition
Linus Torvalds [Sat, 5 Nov 2016 18:46:02 +0000 (11:46 -0700)]
Merge branches 'sched-urgent-for-linus' and 'core-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull stack vmap fixups from Thomas Gleixner:
"Two small patches related to sched_show_task():
- make sure to hold a reference on the task stack while accessing it
- remove the thread_saved_pc printout
.. and add a sanity check into release_task_stack() to catch problems
with task stack references"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/core: Remove pointless printout in sched_show_task()
sched/core: Fix oops in sched_show_task()
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
fork: Add task stack refcounting sanity check and prevent premature task stack freeing
Linus Torvalds [Sat, 5 Nov 2016 18:34:07 +0000 (11:34 -0700)]
Merge tag 'md/4.9-rc3' of git://git./linux/kernel/git/shli/md
Pull MD fixes from Shaohua Li:
"There are several bug fixes queued:
- fix raid5-cache recovery bugs
- fix discard IO error handling for raid1/10
- fix array sync writes bogus position to superblock
- fix IO error handling for raid array with external metadata"
* tag 'md/4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md:
md: be careful not lot leak internal curr_resync value into metadata. -- (all)
raid1: handle read error also in readonly mode
raid5-cache: correct condition for empty metadata write
md: report 'write_pending' state when array in sync
md/raid5: write an empty meta-block when creating log super-block
md/raid5: initialize next_checkpoint field before use
RAID10: ignore discard error
RAID1: ignore discard error
Linus Torvalds [Sat, 5 Nov 2016 18:28:21 +0000 (11:28 -0700)]
Merge tag 'scsi-fixes' of git://git./linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two more important data integrity fixes related to RAID device drivers
which wrongly throw away the SYNCHRONIZE CACHE command in the non-RAID
path and a memory leak in the scsi_debug driver"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: arcmsr: Send SYNCHRONIZE_CACHE command to firmware
scsi: scsi_debug: Fix memory leak if LBP enabled and module is unloaded
scsi: megaraid_sas: Fix data integrity failure for JBOD (passthrough) devices
Linus Torvalds [Sat, 5 Nov 2016 18:26:11 +0000 (11:26 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/dtor/input
Pull input subsystem updates from Dmitry Torokhov.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: psmouse - cleanup Focaltech code
Input: i8042 - add XMG C504 to keyboard reset table
Linus Torvalds [Sat, 5 Nov 2016 18:17:34 +0000 (11:17 -0700)]
Merge tag 'firewire-fixes' of git://git./linux/kernel/git/ieee1394/linux1394
Pull FireWire (IEEE 1394) fixes from Stefan Richter:
- add missing input validation to the firewire-net driver. Invalid
IP-over-1394 encapsulation headers could trigger buffer overflows
(CVE 2016-8633).
- IP-over-1394 link fragmentation headers were read and written
incorrectly, breaking fragmented RX/TX with other OS's stacks.
* tag 'firewire-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
firewire: net: fix fragmented datagram_size off-by-one
firewire: net: guard against rx buffer overflows
Linus Torvalds [Sat, 5 Nov 2016 18:15:09 +0000 (11:15 -0700)]
Merge tag 'media/v4.9-3' of git://git./linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"A series of fixup patches meant to fix the usage of DMA on stack, plus
one warning fixup"
* tag 'media/v4.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (32 commits)
[media] radio-bcm2048: don't ignore errors
[media] pctv452e: fix semicolon.cocci warnings
[media] flexcop-usb: don't use stack for DMA
[media] stk-webcam: don't use stack for DMA
[media] s2255drv: don't use stack for DMA
[media] cpia2_usb: don't use stack for DMA
[media] digitv: handle error code on RC query
[media] dw2102: return error if su3000_power_ctrl() fails
[media] nova-t-usb2: handle error code on RC query
[media] technisat-usb2: use DMA buffers for I2C transfers
[media] pctv452e: don't call BUG_ON() on non-fatal error
[media] pctv452e: don't do DMA on stack
[media] nova-t-usb2: don't do DMA on stack
[media] gp8psk: don't go past the buffer size
[media] gp8psk: don't do DMA on stack
[media] dtv5100: don't do DMA on stack
[media] dtt200u: handle USB control message errors
[media] dtt200u: don't do DMA on stack
[media] dtt200u-fe: handle errors on USB control messages
[media] dtt200u-fe: don't do DMA on stack
...
Linus Torvalds [Sat, 5 Nov 2016 18:11:31 +0000 (11:11 -0700)]
Merge tag 'pci-v4.9-fixes-2' of git://git./linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
- fix for a Qualcomm driver issue that causes a use-before-set crash
- fix for DesignWare iATU unroll support that causes external aborts
when enabling the host bridge
* tag 'pci-v4.9-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: designware: Check for iATU unroll support after initializing host
PCI: qcom: Fix pp->dev usage before assignment
Linus Torvalds [Sat, 5 Nov 2016 17:52:29 +0000 (10:52 -0700)]
Merge tag 'for-linus-
20161104' of git://git.infradead.org/linux-mtd
Pull MTD fixes from Brian Norris:
- MAINTAINERS updates to reflect some new maintainers/submaintainers.
We have some great volunteers who've been developing and reviewing
already. We're going to try a group maintainership model, so
eventually you'll probably see pull requests from people besides me.
- NAND fixes from Boris:
"Three simple fixes:
- fix a non-critical bug in the gpmi driver
- fix a bug in the 'automatic NAND timings selection' feature
introduced in 4.9-rc1
- fix a false positive uninitialized-var warning"
* tag 'for-linus-
20161104' of git://git.infradead.org/linux-mtd:
mtd: mtk: avoid warning in mtk_ecc_encode
mtd: nand: Fix data interface configuration logic
mtd: nand: gpmi: disable the clocks on errors
MAINTAINERS: add more people to the MTD maintainer team
MAINTAINERS: add a maintainer for the SPI NOR subsystem
Linus Torvalds [Sat, 5 Nov 2016 17:49:28 +0000 (10:49 -0700)]
Merge tag 'mmc-v4.9-rc2' of git://git./linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"MMC host:
- sdhci-msm: Fix error path in probe
- dw_mmc-pltfm: Avoid NULL pointer dereference"
* tag 'mmc-v4.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: sdhci-msm: Fix error return code in sdhci_msm_probe()
mmc: dw_mmc-pltfm: fix the potential NULL pointer dereference
Linus Torvalds [Sat, 5 Nov 2016 17:42:20 +0000 (10:42 -0700)]
Merge tag 'gpio-v4.9-3' of git://git./linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Some GPIO fixes for the v4.9 series:
- Fix a nasty file descriptor leak when getting line handles.
- A fix for a cleanup that seemed innocent but created a problem for
drivers instantiating several gpiochips for one single OF node.
- Fix a unpredictable problem using irq_domain_simple() in the mvebu
driver by converting it to a lineas irqdomain"
* tag 'gpio-v4.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio/mvebu: Use irq_domain_add_linear
gpio: of: fix GPIO drivers with multiple gpio_chip for a single node
gpio: GPIO_GET_LINE{HANDLE,EVENT}_IOCTL: Fix file descriptor leak
Linus Torvalds [Sat, 5 Nov 2016 03:12:10 +0000 (20:12 -0700)]
Merge tag 'nfsd-4.9-1' of git://linux-nfs.org/~bfields/linux
Pull nfsd bugfixes from Bruce Fields:
"Fixes for some recent regressions including fallout from the vmalloc'd
stack change (after which we can no longer encrypt stuff on the
stack)"
* tag 'nfsd-4.9-1' of git://linux-nfs.org/~bfields/linux:
nfsd: Fix general protection fault in release_lock_stateid()
svcrdma: backchannel cannot share a page for send and rcv buffers
sunrpc: fix some missing rq_rbuffer assignments
sunrpc: don't pass on-stack memory to sg_set_buf
nfsd: move blocked lock handling under a dedicated spinlock
Linus Torvalds [Sat, 5 Nov 2016 03:08:16 +0000 (20:08 -0700)]
Merge branch 'for-4.9-rc3' of git://git./linux/kernel/git/kdave/linux
Pull btrfs fixes from Chris Mason:
"Some fixes that Dave Sterba collected. We held off on these last week
because I was focused on the memory corruption testing"
* 'for-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: fix WARNING in btrfs_select_ref_head()
Btrfs: remove some no-op casts
btrfs: pass correct args to btrfs_async_run_delayed_refs()
btrfs: make file clone aware of fatal signals
btrfs: qgroup: Prevent qgroup->reserved from going subzero
Btrfs: kill BUG_ON in do_relocation
Linus Torvalds [Sat, 5 Nov 2016 03:03:14 +0000 (20:03 -0700)]
Merge branch 'overlayfs-linus' of git://git./linux/kernel/git/mszeredi/vfs
Pull overlayfs fixes from Miklos Szeredi:
"Fix two more POSIX ACL bugs introduced in 4.8 and add a missing fsync
during copy up to prevent possible data loss"
* 'overlayfs-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
ovl: fsync after copy-up
ovl: fix get_acl() on tmpfs
ovl: update S_ISGID when setting posix ACLs
Linus Torvalds [Fri, 4 Nov 2016 20:30:13 +0000 (13:30 -0700)]
Merge tag 'drm-fixes-for-v4.9-rc4' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Fixes for amdgpu, radeon, intel, imx and virtio-gpu.
This is a bit larger than I'd like, but I had some stuff I meant to
send for -rc3 but was waiting for the PAT regression fix to land. So
this is really fixes for rc3 and rc4 in one go.
There are a set of fixes for an oops we've been seeing around MST
display unplug, along with more suspend/resume and shutdown fixes for
amdgpu, one power management follow on fix for nouveau, and set of imx
fixes, and a single virtio-gpu regression fix"
* tag 'drm-fixes-for-v4.9-rc4' of git://people.freedesktop.org/~airlied/linux: (54 commits)
virtio-gpu: fix vblank events
drm/nouveau/acpi: fix check for power resources support
drm/i915: Fix SKL+ 90/270 degree rotated plane coordinate computation
drm/i915: Remove two invalid warns
drm/i915: Rotated view does not need a fence
drm/i915/fbc: fix CFB size calculation for gen8+
drm: i915: Wait for fences on new fb, not old
drm/i915: Clean up DDI DDC/AUX CH sanitation
drm/i915: Respect alternate_aux_channel for all DDI ports
drm/i915/gen9: fix watermarks when using the pipe scaler
drm/i915: Fix mismatched INIT power domain disabling during suspend
drm/i915: fix a read size argument
drm/i915: Use fence_write() from rpm resume
drm/i915/gen9: fix DDB partitioning for multi-screen cases
drm/i915: workaround sparse warning on variable length arrays
drm/i915: keep declarations in i915_drv.h
drm/amd/powerplay: fix bug get wrong evv voltage of Polaris.
drm/amdgpu/si_dpm: workaround for SI kickers
drm/radeon/si_dpm: workaround for SI kickers
drm/amdgpu: fix s3 resume back, uvd dpm randomly can't disable.
...
Niklas Cassel [Fri, 14 Oct 2016 21:54:55 +0000 (23:54 +0200)]
PCI: designware: Check for iATU unroll support after initializing host
dw_pcie_iatu_unroll_enabled() reads a dbi_base register. Reading any
dbi_base register before pp->ops->host_init has been called causes
"imprecise external abort" on platforms like ARTPEC-6, where the PCIe
module is disabled at boot and first enabled in pp->ops->host_init. Move
dw_pcie_iatu_unroll_enabled() to dw_pcie_setup_rc(), since it is after
pp->ops->host_init, but before pp->iatu_unroll_enabled is actually used.
Fixes: a0601a470537 ("PCI: designware: Add iATU Unroll feature")
Tested-by: James Le Cuirot <chewi@gentoo.org>
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Joao Pinto <jpinto@synopsys.com>
Acked-by: Olof Johansson <olof@lixom.net>
Linus Torvalds [Fri, 4 Nov 2016 20:08:05 +0000 (13:08 -0700)]
Merge tag 'for-linus' of git://git./virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"One NULL pointer dereference, and two fixes for regressions introduced
during the merge window.
The rest are fixes for MIPS, s390 and nested VMX"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
kvm: x86: Check memopp before dereference (CVE-2016-8630)
kvm: nVMX: VMCLEAR an active shadow VMCS after last use
KVM: x86: drop TSC offsetting kvm_x86_ops to fix KVM_GET/SET_CLOCK
KVM: x86: fix wbinvd_dirty_mask use-after-free
kvm/x86: Show WRMSR data is in hex
kvm: nVMX: Fix kernel panics induced by illegal INVEPT/INVVPID types
KVM: document lock orders
KVM: fix OOPS on flush_work
KVM: s390: Fix STHYI buffer alignment for diag224
KVM: MIPS: Precalculate MMIO load resume PC
KVM: MIPS: Make ERET handle ERL before EXL
KVM: MIPS: Fix lazy user ASID regenerate for SMP
Linus Torvalds [Fri, 4 Nov 2016 20:03:57 +0000 (13:03 -0700)]
Merge branch 'upstream' of git://git.linux-mips.org/ralf/upstream-linus
Pull MIPS fixes from Ralf Baechle:
"A set of MIPS fixes for 4.9:
- lots of fixes for printk continuations
- six fixes for FP related code.
- fix max_low_pfn with disabled highmem
- fix KASLR handling of NULL FDT and KASLR for generic kernels
- fix build of compressed image
- provide default mips_cpc_default_phys_base to ignore CPC
- fix reboot on Malta"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Fix max_low_pfn with disabled highmem
MIPS: Correct MIPS I FP sigcontext layout
MIPS: Fix ISA I/II FP signal context offsets
MIPS: Remove FIR from ISA I FP signal context
MIPS: Fix ISA I FP sigcontext access violation handling
MIPS: Fix FCSR Cause bit handling for correct SIGFPE issue
MIPS: ptrace: Also initialize the FP context on individual FCSR writes
MIPS: dump_tlb: Fix printk continuations
MIPS: Fix __show_regs() output
MIPS: traps: Fix output of show_code
MIPS: traps: Fix output of show_stacktrace
MIPS: traps: Fix output of show_backtrace
MIPS: Fix build of compressed image
MIPS: generic: Fix KASLR for generic kernel.
MIPS: KASLR: Fix handling of NULL FDT
MIPS: Malta: Fixup reboot
MIPS: CPC: Provide default mips_cpc_default_phys_base to ignore CPC
Linus Torvalds [Fri, 4 Nov 2016 20:01:13 +0000 (13:01 -0700)]
Merge branch 'parisc-4.9-3' of git://git./linux/kernel/git/deller/parisc-linux
Pull parisc updates from Helge Deller:
"The first three patches are trivial and add some required KERN_CONT,
ignore the new pkey syscalls on parisc and use the LINUX_GATEWAY_ADDR
define instead of hardcoded values.
The two patches from Dave Anglin are important.
The first one avoids trashing the sr2 and sr3 space registers in the
Light-weight syscall path. Especially the usage of sr3 is critical
since it may get trashed by the interrupt handler.
The second patch is even more important and tagged for stable series.
It protects one critical section in the syscall entry path by
disabling local interrupts. Without disabling interrupts, the sr7
space register may not be in sync with the current stack setup and
thus an incoming hardware interrupt may destroy memory in random
userspace areas"
* 'parisc-4.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Ignore the pkey system calls for now
parisc: Use LINUX_GATEWAY_ADDR define instead of hardcoded value
parisc: Ensure consistent state when switching to kernel stack at syscall entry
parisc: Avoid trashing sr2 and sr3 in LWS code
parisc: use KERN_CONT when printing device inventory
Vladimir Zapolskiy [Mon, 31 Oct 2016 19:46:24 +0000 (21:46 +0200)]
i2c: core: fix NULL pointer dereference under race condition
Race condition between registering an I2C device driver and
deregistering an I2C adapter device which is assumed to manage that
I2C device may lead to a NULL pointer dereference due to the
uninitialized list head of driver clients.
The root cause of the issue is that the I2C bus may know about the
registered device driver and thus it is matched by bus_for_each_drv(),
but the list of clients is not initialized and commonly it is NULL,
because I2C device drivers define struct i2c_driver as static and
clients field is expected to be initialized by I2C core:
i2c_register_driver() i2c_del_adapter()
driver_register() ...
bus_add_driver() ...
... bus_for_each_drv(..., __process_removed_adapter)
... i2c_do_del_adapter()
... list_for_each_entry_safe(..., &driver->clients, ...)
INIT_LIST_HEAD(&driver->clients);
To solve the problem it is sufficient to do clients list head
initialization before calling driver_register().
The problem was found while using an I2C device driver with a sluggish
registration routine on a bus provided by a physically detachable I2C
master controller, but practically the oops may be reproduced under
the race between arbitraty I2C device driver registration and managing
I2C bus device removal e.g. by unbinding the latter over sysfs:
% echo
21a4000.i2c > /sys/bus/platform/drivers/imx-i2c/unbind
Unable to handle kernel NULL pointer dereference at virtual address
00000000
Internal error: Oops: 17 [#1] SMP ARM
CPU: 2 PID: 533 Comm: sh Not tainted 4.9.0-rc3+ #61
Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
task:
e5ada400 task.stack:
e4936000
PC is at i2c_do_del_adapter+0x20/0xcc
LR is at __process_removed_adapter+0x14/0x1c
Flags: NzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
Control:
10c5387d Table:
35bd004a DAC:
00000051
Process sh (pid: 533, stack limit = 0xe4936210)
Stack: (0xe4937d28 to 0xe4938000)
Backtrace:
[<
c0667be0>] (i2c_do_del_adapter) from [<
c0667cc0>] (__process_removed_adapter+0x14/0x1c)
[<
c0667cac>] (__process_removed_adapter) from [<
c0516998>] (bus_for_each_drv+0x6c/0xa0)
[<
c051692c>] (bus_for_each_drv) from [<
c06685ec>] (i2c_del_adapter+0xbc/0x284)
[<
c0668530>] (i2c_del_adapter) from [<
bf0110ec>] (i2c_imx_remove+0x44/0x164 [i2c_imx])
[<
bf0110a8>] (i2c_imx_remove [i2c_imx]) from [<
c051a838>] (platform_drv_remove+0x2c/0x44)
[<
c051a80c>] (platform_drv_remove) from [<
c05183d8>] (__device_release_driver+0x90/0x12c)
[<
c0518348>] (__device_release_driver) from [<
c051849c>] (device_release_driver+0x28/0x34)
[<
c0518474>] (device_release_driver) from [<
c0517150>] (unbind_store+0x80/0x104)
[<
c05170d0>] (unbind_store) from [<
c0516520>] (drv_attr_store+0x28/0x34)
[<
c05164f8>] (drv_attr_store) from [<
c0298acc>] (sysfs_kf_write+0x50/0x54)
[<
c0298a7c>] (sysfs_kf_write) from [<
c029801c>] (kernfs_fop_write+0x100/0x214)
[<
c0297f1c>] (kernfs_fop_write) from [<
c0220130>] (__vfs_write+0x34/0x120)
[<
c02200fc>] (__vfs_write) from [<
c0221088>] (vfs_write+0xa8/0x170)
[<
c0220fe0>] (vfs_write) from [<
c0221e74>] (SyS_write+0x4c/0xa8)
[<
c0221e28>] (SyS_write) from [<
c0108a20>] (ret_fast_syscall+0x0/0x1c)
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
James Hogan [Tue, 1 Nov 2016 13:59:09 +0000 (13:59 +0000)]
MIPS: Fix max_low_pfn with disabled highmem
When low memory doesn't reach HIGHMEM_START (e.g. up to 256MB at PA=0 is
common) and highmem is present above HIGHMEM_START (e.g. on Malta the
RAM overlayed by the IO region is aliased at PA=0x90000000), max_low_pfn
will be initially calculated very large and then clipped down to
HIGHMEM_START.
This causes crashes when reading /sys/kernel/mm/page_idle/bitmap
(i.e. CONFIG_IDLE_PAGE_TRACKING=y) when highmem is disabled. pfn_valid()
will compare against max_mapnr which is derived from max_low_pfn when
there is no highend_pfn set up, and will return true for PFNs right up
to HIGHMEM_START, even though they are beyond the end of low memory and
no page structs will actually exist for these PFNs.
This is fixed by skipping high memory regions when initially calculating
max_low_pfn if highmem is disabled, so it doesn't get clipped too high.
We also clip regions which overlap the highmem boundary when highmem is
disabled, so that max_pfn doesn't extend into highmem either.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14490/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Maciej W. Rozycki [Mon, 31 Oct 2016 16:27:40 +0000 (16:27 +0000)]
MIPS: Correct MIPS I FP sigcontext layout
Complement commit
80cbfad79096 ("MIPS: Correct MIPS I FP context
layout") and correct the way Floating Point General registers are stored
in a signal context with MIPS I hardware.
Use the S.D and L.D assembly macros to have pairs of SWC1 instructions
and pairs of LWC1 instructions produced, respectively, in an arrangement
which makes the memory representation of floating-point data passed
compatible with that used by hardware SDC1 and LDC1 instructions, where
available, regardless of the hardware endianness used. This matches the
layout used by r4k_fpu.S, ensuring run-time compatibility for MIPS I
software across all o32 hardware platforms.
Define an EX2 macro to handle exceptions from both hardware instructions
implicitly produced from S.D and L.D assembly macros.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14477/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Maciej W. Rozycki [Mon, 31 Oct 2016 16:27:01 +0000 (16:27 +0000)]
MIPS: Fix ISA I/II FP signal context offsets
Fix a regression introduced with commit
2db9ca0a3551 ("MIPS: Use struct
mips_abi offsets to save FP context") for MIPS I/I FP signal contexts,
by converting save/restore code to the updated internal API. Start FGR
offsets from 0 rather than SC_FPREGS from $a0 and use $a1 rather than
the offset of SC_FPC_CSR from $a0 for the Floating Point Control/Status
Register (FCSR).
Document the new internal API and adjust assembly code formatting for
consistency.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14476/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Maciej W. Rozycki [Mon, 31 Oct 2016 16:26:24 +0000 (16:26 +0000)]
MIPS: Remove FIR from ISA I FP signal context
Complement commit
e50c0a8fa60d ("Support the MIPS32 / MIPS64 DSP ASE.")
and remove the Floating Point Implementation Register (FIR) from the FP
register set recorded in a signal context with MIPS I processors too, in
line with the change applied to r4k_fpu.S.
The `sc_fpc_eir' slot is unused according to our current ABI and the FIR
register is read-only and always directly accessible from user software.
[ralf@linux-mips.org: This is also required because the next commit depends
on it.]
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14475/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Maciej W. Rozycki [Mon, 31 Oct 2016 16:25:44 +0000 (16:25 +0000)]
MIPS: Fix ISA I FP sigcontext access violation handling
Complement commit
0ae8dceaebe3 ("Merge with 2.3.10.") and use the local
`fault' handler to recover from FP sigcontext access violation faults,
like corresponding code does in r4k_fpu.S. The `bad_stack' handler is
in syscall.c and is not suitable here as we want to propagate the error
condition up through the caller rather than killing the thread outright.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14474/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Maciej W. Rozycki [Fri, 28 Oct 2016 07:21:03 +0000 (08:21 +0100)]
MIPS: Fix FCSR Cause bit handling for correct SIGFPE issue
Sanitize FCSR Cause bit handling, following a trail of past attempts:
* commit
4249548454f7 ("MIPS: ptrace: Fix FP context restoration FCSR
regression"),
* commit
443c44032a54 ("MIPS: Always clear FCSR cause bits after
emulation"),
* commit
64bedffe4968 ("MIPS: Clear [MSA]FPE CSR.Cause after
notify_die()"),
* commit
b1442d39fac2 ("MIPS: Prevent user from setting FCSR cause
bits"),
* commit
b54d2901517d ("Properly handle branch delay slots in connection
with signals.").
Specifically do not mask these bits out in ptrace(2) processing and send
a SIGFPE signal instead whenever a matching pair of an FCSR Cause and
Enable bit is seen as execution of an affected context is about to
resume. Only then clear Cause bits, and even then do not clear any bits
that are set but masked with the respective Enable bits. Adjust Cause
bit clearing throughout code likewise, except within the FPU emulator
proper where they are set according to IEEE 754 exceptions raised as the
operation emulated executed. Do so so that any IEEE 754 exceptions
subject to their default handling are recorded like with operations
executed by FPU hardware.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14460/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Maciej W. Rozycki [Fri, 28 Oct 2016 07:20:09 +0000 (08:20 +0100)]
MIPS: ptrace: Also initialize the FP context on individual FCSR writes
Complement commit
ac9ad83bc318 ("MIPS: prevent FP context set via ptrace
being discarded") and also initialize the FP context whenever FCSR alone
is written with a PTRACE_POKEUSR request addressing FPC_CSR, rather than
along with the full FPU register set in the case of the PTRACE_SETFPREGS
request.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14459/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
James Hogan [Fri, 21 Oct 2016 19:06:40 +0000 (20:06 +0100)]
MIPS: dump_tlb: Fix printk continuations
Since commit
4bcc595ccd80 ("printk: reinstate KERN_CONT for printing
continuation lines") the output from TLB dumps on MIPS has been
pretty unreadable due to the lack of KERN_CONT markers. Use pr_cont to
provide the appropriate markers & restore the expected output.
Continuation is also used for the second line of each TLB entry printed
in dump_tlb.c even though it has a newline, since it is a continuation
of the interpretation of the same TLB entry. For example:
[ 46.371884] Index: 0 pgmask=16kb va=
77654000 asid=73 gid=00
[ri=0 xi=0 pa=
ffc18000 c=5 d=0 v=1 g=0] [ri=0 xi=0 pa=
ffc1c000 c=5 d=0 v=1 g=0]
[ 46.385380] Index: 12 pgmask=16kb va=
004b4000 asid=73 gid=00
[ri=0 xi=0 pa=
00000000 c=0 d=0 v=0 g=0] [ri=0 xi=0 pa=
ffb00000 c=5 d=1 v=1 g=0]
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Maciej W. Rozycki <macro@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14444/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Paul Burton [Wed, 19 Oct 2016 13:33:23 +0000 (14:33 +0100)]
MIPS: Fix __show_regs() output
Since commit
4bcc595ccd80 ("printk: reinstate KERN_CONT for printing
continuation lines") the output from __show_regs() on MIPS has been
pretty unreadable due to the lack of KERN_CONT markers. Use pr_cont to
provide the appropriate markers & restore the expected register output.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Maciej W. Rozycki <macro@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14432/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Matt Redfearn [Wed, 19 Oct 2016 13:33:22 +0000 (14:33 +0100)]
MIPS: traps: Fix output of show_code
Since commit
4bcc595ccd80 ("printk: reinstate KERN_CONT for printing
continuation lines") the output from show_code on MIPS has been
pretty unreadable due to the lack of KERN_CONT markers. Use pr_cont to
provide the appropriate markers & restore the expected output.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Maciej W. Rozycki <macro@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14431/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Matt Redfearn [Wed, 19 Oct 2016 13:33:21 +0000 (14:33 +0100)]
MIPS: traps: Fix output of show_stacktrace
Since commit
4bcc595ccd80 ("printk: reinstate KERN_CONT for printing
continuation lines") the output from show_stacktrace on MIPS has been
pretty unreadable due to the lack of KERN_CONT markers. Use pr_cont to
provide the appropriate markers & restore the expected output. Also
start a new line with printk such that the presence of timing
information does not interfere with output.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Maciej W. Rozycki <macro@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14430/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Matt Redfearn [Wed, 19 Oct 2016 13:33:20 +0000 (14:33 +0100)]
MIPS: traps: Fix output of show_backtrace
Since commit
4bcc595ccd80 ("printk: reinstate KERN_CONT for printing
continuation lines") the output from show_backtrace on MIPS has been
pretty unreadable due to the lack of KERN_CONT markers. Use pr_cont to
provide the appropriate markers & restore the expected output.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Maciej W. Rozycki <macro@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14429/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Matt Redfearn [Mon, 17 Oct 2016 09:09:39 +0000 (10:09 +0100)]
MIPS: Fix build of compressed image
Changes introduced to arch/mips/Makefile for the generic kernel resulted
in build errors when making a compressed image if platform-y has multiple
values, like this:
make[2]: *** No rule to make target `alchemy/'.
make[1]: *** [vmlinuz] Error 2
make[1]: Target `_all' not remade because of errors.
make: *** [sub-make] Error 2
make: Target `_all' not remade because of errors.
Fix this by quoting $(platform-y) as it is passed to the Makefile in
arch/mips/boot/compressed/Makefile
Reported-by: kernelci.org bot <bot@kernelci.org>
Link: https://storage.kernelci.org/next/next-20161017/mips-gpr_defconfig/build.log
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14405/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Matt Redfearn [Mon, 17 Oct 2016 16:25:24 +0000 (17:25 +0100)]
MIPS: generic: Fix KASLR for generic kernel.
The KASLR code requires that the plat_get_fdt() function return the
address of the device tree, and it must be available early in the boot,
before prom_init() is called. Move the code determining the address of
the device tree into plat_get_fdt, and call that from prom_init().
The fdt pointer will be set up by plat_get_fdt() called from
relocate_kernel initially and once the relocated kernel has started,
prom_init() will use it again to determine the address in the relocated
image.
Fixes: eed0eabd12ef ("MIPS: generic: Introduce generic DT-based board support")
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14415/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Matt Redfearn [Mon, 17 Oct 2016 16:21:46 +0000 (17:21 +0100)]
MIPS: KASLR: Fix handling of NULL FDT
If platform code returns a NULL pointer to the FDT, initial_boot_params
will not get set to a valid pointer and attempting to find the /chosen
node in it will cause a NULL pointer dereference and the kernel to crash
immediately on startup - with no output to the console.
Fix this by checking that initial_boot_params is valid before using it.
Fixes: 405bc8fd12f5 ("MIPS: Kernel: Implement KASLR using CONFIG_RELOCATABLE")
Cc: stable@vger.kernel.org # 4.7+
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14414/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Paul Burton [Fri, 14 Oct 2016 09:17:32 +0000 (10:17 +0100)]
MIPS: Malta: Fixup reboot
Commit
10b6ea0959de ("MIPS: Malta: Use syscon-reboot driver to reboot")
converted the Malta board to use the generic syscon-reboot driver to
handle reboots, but incorrectly used the value 0x4d rather than 0x42 as
the magic to write to the reboot register.
I also incorrectly believed that syscon/regmap would default to native
endianness, but this isn't the case. Force this by specifying with a
native-endian property in the devicetree.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Fixes: 10b6ea0959de ("MIPS: Malta: Use syscon-reboot driver to reboot")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Cc: linux-mips@linux-mips.org
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Maciej W. Rozycki <macro@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/14396/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Paul Burton [Sat, 15 Oct 2016 22:03:43 +0000 (23:03 +0100)]
MIPS: CPC: Provide default mips_cpc_default_phys_base to ignore CPC
Provide a default implementation of mips_cpc_default_phys_base() which
simply returns 0, and adjust mips_cpc_phys_base() to allow for
mips_cpc_default_phys_base() returning 0. This allows kernels which
include CPC support to be built without platform code & simply ignore
the CPC if it wasn't already enabled by the bootloader.
This fixes link failures such as the following from generic defconfigs:
arch/mips/built-in.o: In function `mips_cpc_phys_base':
arch/mips/kernel/mips-cpc.c:47: undefined reference to `mips_cpc_default_phys_base'
[ralf@linux-mips.org: changed prototype for coding style compliance.]
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14401/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Stefan Richter [Sun, 30 Oct 2016 16:32:01 +0000 (17:32 +0100)]
firewire: net: fix fragmented datagram_size off-by-one
RFC 2734 defines the datagram_size field in fragment encapsulation
headers thus:
datagram_size: The encoded size of the entire IP datagram. The
value of datagram_size [...] SHALL be one less than the value of
Total Length in the datagram's IP header (see STD 5, RFC 791).
Accordingly, the eth1394 driver of Linux 2.6.36 and older set and got
this field with a -/+1 offset:
ether1394_tx() /* transmit */
ether1394_encapsulate_prep()
hdr->ff.dg_size = dg_size - 1;
ether1394_data_handler() /* receive */
if (hdr->common.lf == ETH1394_HDR_LF_FF)
dg_size = hdr->ff.dg_size + 1;
else
dg_size = hdr->sf.dg_size + 1;
Likewise, I observe OS X 10.4 and Windows XP Pro SP3 to transmit 1500
byte sized datagrams in fragments with datagram_size=1499 if link
fragmentation is required.
Only firewire-net sets and gets datagram_size without this offset. The
result is lacking interoperability of firewire-net with OS X, Windows
XP, and presumably Linux' eth1394. (I did not test with the latter.)
For example, FTP data transfers to a Linux firewire-net box with max_rec
smaller than the 1500 bytes MTU
- from OS X fail entirely,
- from Win XP start out with a bunch of fragmented datagrams which
time out, then continue with unfragmented datagrams because Win XP
temporarily reduces the MTU to 576 bytes.
So let's fix firewire-net's datagram_size accessors.
Note that firewire-net thereby loses interoperability with unpatched
firewire-net, but only if link fragmentation is employed. (This happens
with large broadcast datagrams, and with large datagrams on several
FireWire CardBus cards with smaller max_rec than equivalent PCI cards,
and it can be worked around by setting a small enough MTU.)
Cc: stable@vger.kernel.org
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Sat, 29 Oct 2016 19:28:18 +0000 (21:28 +0200)]
firewire: net: guard against rx buffer overflows
The IP-over-1394 driver firewire-net lacked input validation when
handling incoming fragmented datagrams. A maliciously formed fragment
with a respectively large datagram_offset would cause a memcpy past the
datagram buffer.
So, drop any packets carrying a fragment with offset + length larger
than datagram_size.
In addition, ensure that
- GASP header, unfragmented encapsulation header, or fragment
encapsulation header actually exists before we access it,
- the encapsulated datagram or fragment is of nonzero size.
Reported-by: Eyal Itkin <eyal.itkin@gmail.com>
Reviewed-by: Eyal Itkin <eyal.itkin@gmail.com>
Fixes: CVE 2016-8633
Cc: stable@vger.kernel.org
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Linus Torvalds [Tue, 1 Nov 2016 23:47:18 +0000 (17:47 -0600)]
sched/core: Remove pointless printout in sched_show_task()
In sched_show_task() we print out a useless hex number, not even a
symbol, and there's a big question mark whether this even makes sense
anyway, I suspect we should just remove it all.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Andy Lutomirski <luto@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: bp@alien8.de
Cc: brgerst@gmail.com
Cc: jann@thejh.net
Cc: keescook@chromium.org
Cc: linux-api@vger.kernel.org
Cc: tycho.andersen@canonical.com
Link: http://lkml.kernel.org/r/CA+55aFzphURPFzAvU4z6Moy7ZmimcwPuUdYU8bj9z0J+S8X1rw@mail.gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Tetsuo Handa [Wed, 2 Nov 2016 10:50:29 +0000 (19:50 +0900)]
sched/core: Fix oops in sched_show_task()
When CONFIG_THREAD_INFO_IN_TASK=y, it is possible that an exited thread
remains in the task list after its stack pointer was already set to NULL.
Therefore, thread_saved_pc() and stack_not_used() in sched_show_task()
will trigger NULL pointer dereference if an attempt to dump such thread's
traces (e.g. SysRq-t, khungtaskd) is made.
Since show_stack() in sched_show_task() calls try_get_task_stack() and
sched_show_task() is called from interrupt context, calling
try_get_task_stack() from sched_show_task() will be safe as well.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Acked-by: Andy Lutomirski <luto@kernel.org>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: bp@alien8.de
Cc: brgerst@gmail.com
Cc: jann@thejh.net
Cc: keescook@chromium.org
Cc: linux-api@vger.kernel.org
Cc: tycho.andersen@canonical.com
Link: http://lkml.kernel.org/r/201611021950.FEJ34368.HFFJOOMLtQOVSF@I-love.SAKURA.ne.jp
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Dave Airlie [Thu, 3 Nov 2016 00:18:20 +0000 (10:18 +1000)]
Merge tag 'drm-intel-fixes-2016-11-01' of git://anongit.freedesktop.org/drm-intel into drm-fixes
batch of scattered i915 fixes.
* tag 'drm-intel-fixes-2016-11-01' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Fix SKL+ 90/270 degree rotated plane coordinate computation
drm/i915: Remove two invalid warns
drm/i915: Rotated view does not need a fence
drm/i915/fbc: fix CFB size calculation for gen8+
drm: i915: Wait for fences on new fb, not old
drm/i915: Clean up DDI DDC/AUX CH sanitation
drm/i915: Respect alternate_aux_channel for all DDI ports
drm/i915/gen9: fix watermarks when using the pipe scaler
drm/i915: Fix mismatched INIT power domain disabling during suspend
drm/i915: fix a read size argument
drm/i915: Use fence_write() from rpm resume
drm/i915/gen9: fix DDB partitioning for multi-screen cases
drm/i915: workaround sparse warning on variable length arrays
drm/i915: keep declarations in i915_drv.h
Dave Airlie [Thu, 3 Nov 2016 00:17:50 +0000 (10:17 +1000)]
Merge tag 'imx-drm-fixes-
20161021' of git://git.pengutronix.de/pza/linux into drm-fixes
imx-drm plane, build warning, and error handling fixes
- some fixes for active plane reconfiguration support
- hide unused label in case of disabled CONFIG_DRM_FBDEV_EMULATION,
which caused a build warning
- fixed error handling in imx_drm_bind
- disallow odd x/y plane offsets for chroma subsampled formats
- disable local alpha when switching from a format with alpha
channel to an opaque format
* tag 'imx-drm-fixes-
20161021' of git://git.pengutronix.de/pza/linux:
drm/imx: ipuv3-plane: disable local alpha for planes without alpha channel
drm/imx: ipuv3-plane: make sure x/y offsets are even in case of chroma subsampling
drm/imx: ipuv3-plane: Access old u/vbo properly in ->atomic_check for YU12/YV12
drm/imx: drm_dev_alloc() returns error pointers
drm/imx: ipuv3-plane: Skip setting u/vbo only when we don't need modeset
drm/imx: ipuv3-plane: Switch EBA buffer only when we don't need modeset
gpu: ipu-v3: Use ERR_CAST instead of ERR_PTR(PTR_ERR())
drm/imx: hide an unused label
Gerd Hoffmann [Tue, 18 Oct 2016 17:32:30 +0000 (15:32 -0200)]
virtio-gpu: fix vblank events
virtio-gpu sends vblank events in virtio_gpu_crtc_atomic_flush, and
because of that it must be called for disabled planes too. Ask
drm_atomic_helper_commit_planes to do that.
v2: update to use new drm_atomic_helper_commit_planes() API.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Helge Deller [Sat, 29 Oct 2016 21:47:57 +0000 (23:47 +0200)]
parisc: Ignore the pkey system calls for now
Signed-off-by: Helge Deller <deller@gmx.de>
Helge Deller [Sat, 29 Oct 2016 21:52:43 +0000 (23:52 +0200)]
parisc: Use LINUX_GATEWAY_ADDR define instead of hardcoded value
LINUX_GATEWAY_ADDR is defined in unistd.h. Let's use it.
Signed-off-by: Helge Deller <deller@gmx.de>
John David Anglin [Sat, 29 Oct 2016 03:00:34 +0000 (23:00 -0400)]
parisc: Ensure consistent state when switching to kernel stack at syscall entry
We have one critical section in the syscall entry path in which we switch from
the userspace stack to kernel stack. In the event of an external interrupt, the
interrupt code distinguishes between those two states by analyzing the value of
sr7. If sr7 is zero, it uses the kernel stack. Therefore it's important, that
the value of sr7 is in sync with the currently enabled stack.
This patch now disables interrupts while executing the critical section. This
prevents the interrupt handler to possibly see an inconsistent state which in
the worst case can lead to crashes.
Interestingly, in the syscall exit path interrupts were already disabled in the
critical section which switches back to the userspace stack.
Cc: <stable@vger.kernel.org>
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
John David Anglin [Fri, 28 Oct 2016 20:13:42 +0000 (22:13 +0200)]
parisc: Avoid trashing sr2 and sr3 in LWS code
There is no need to trash sr2 and sr3 in the Light-weight syscall (LWS). sr2
already points to kernel space (it's zero in userspace, otherwise syscalls
wouldn't work), and since the LWS code is executed in userspace, we can simply
ignore to preload sr3.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
Helge Deller [Fri, 28 Oct 2016 18:56:07 +0000 (20:56 +0200)]
parisc: use KERN_CONT when printing device inventory
Recent changes to printk require KERN_CONT uses to continue logging messages.
So add KERN_CONT to output of device inventory.
Signed-off-by: Helge Deller <deller@gmx.de>
Owen Hofmann [Thu, 27 Oct 2016 18:25:52 +0000 (11:25 -0700)]
kvm: x86: Check memopp before dereference (CVE-2016-8630)
Commit
41061cdb98 ("KVM: emulate: do not initialize memopp") removes a
check for non-NULL under incorrect assumptions. An undefined instruction
with a ModR/M byte with Mod=0 and R/M-5 (e.g. 0xc7 0x15) will attempt
to dereference a null pointer here.
Fixes: 41061cdb98a0bec464278b4db8e894a3121671f5
Message-Id: <
1477592752-126650-2-git-send-email-osh@google.com>
Signed-off-by: Owen Hofmann <osh@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Jim Mattson [Fri, 28 Oct 2016 15:29:39 +0000 (08:29 -0700)]
kvm: nVMX: VMCLEAR an active shadow VMCS after last use
After a successful VM-entry with the "VMCS shadowing" VM-execution
control set, the shadow VMCS referenced by the VMCS link pointer field
in the current VMCS becomes active on the logical processor.
A VMCS that is made active on more than one logical processor may become
corrupted. Therefore, before an active VMCS can be migrated to another
logical processor, the first logical processor must execute a VMCLEAR
for the active VMCS. VMCLEAR both ensures that all VMCS data are written
to memory and makes the VMCS inactive.
Signed-off-by: Jim Mattson <jmattson@google.com>
Reviewed-By: David Matlack <dmatlack@google.com>
Message-Id: <
1477668579-22555-1-git-send-email-jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Paolo Bonzini [Mon, 31 Oct 2016 23:39:48 +0000 (00:39 +0100)]
KVM: x86: drop TSC offsetting kvm_x86_ops to fix KVM_GET/SET_CLOCK
Since commit
a545ab6a0085 ("kvm: x86: add tsc_offset field to struct
kvm_vcpu_arch", 2016-09-07) the offset between host and L1 TSC is
cached and need not be fished out of the VMCS or VMCB. This means
that we can implement adjust_tsc_offset_guest and read_l1_tsc
entirely in generic code. The simplification is particularly
significant for VMX code, where vmx->nested.vmcs01_tsc_offset
was duplicating what is now in vcpu->arch.tsc_offset. Therefore
the vmcs01_tsc_offset can be dropped completely.
More importantly, this fixes KVM_GET_CLOCK/KVM_SET_CLOCK
which, after commit
108b249c453d ("KVM: x86: introduce get_kvmclock_ns",
2016-09-01) called read_l1_tsc while the VMCS was not loaded.
It thus returned bogus values on Intel CPUs.
Fixes: 108b249c453dd7132599ab6dc7e435a7036c193f
Reported-by: Roman Kagan <rkagan@virtuozzo.com>
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Linus Torvalds [Tue, 1 Nov 2016 23:48:46 +0000 (17:48 -0600)]
Merge tag 'gcc-plugins-v4.9-rc4' of git://git./linux/kernel/git/kees/linux
Pull gcc plugin fixes from Kees Cook:
- make sure required exports from gcc plugins are visible to gcc
- switch latent_entropy to unsigned long to avoid stack frame bloat
* tag 'gcc-plugins-v4.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
latent_entropy: Fix wrong gcc code generation with 64 bit variables
gcc-plugins: Export symbols needed by gcc
Linus Torvalds [Tue, 1 Nov 2016 22:56:05 +0000 (16:56 -0600)]
Merge tag 'for_linus' of git://git./linux/kernel/git/mst/vhost
Pull virtio updates from Michael Tsirkin:
"Tests, fixes and cleanups.
Just minor tweaks, there's nothing major in this cycle"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio_ring: mark vring_dma_dev inline
virtio/vhost: add Jason to list of maintainers
virtio_blk: Delete an unnecessary initialisation in init_vq()
virtio_blk: Use kmalloc_array() in init_vq()
virtio: remove config.c
virtio: console: Unlock vqs while freeing buffers
ringtest: poll for new buffers once before updating event index
ringtest: commonize implementation of poll_avail/poll_used
ringtest: use link-time optimization
virtio: update balloon size in balloon "probe"
virtio_ring: Make interrupt suppression spec compliant
virtio_pci: Limit DMA mask to 44 bits for legacy virtio devices
Linus Torvalds [Tue, 1 Nov 2016 22:52:56 +0000 (16:52 -0600)]
Merge tag 'vfio-v4.9-rc4' of git://github.com/awilliam/linux-vfio
Pull VFIO fix from Alex Williamson:
"SET_IRQS ioctl parameter sanitization (Vlad Tsyrklevich)"
* tag 'vfio-v4.9-rc4' of git://github.com/awilliam/linux-vfio:
vfio/pci: Fix integer overflows, bitmask check
Chuck Lever [Sat, 29 Oct 2016 22:19:03 +0000 (18:19 -0400)]
nfsd: Fix general protection fault in release_lock_stateid()
When I push NFSv4.1 / RDMA hard, (xfstests generic/089, for example),
I get this crash on the server:
Oct 28 22:04:30 klimt kernel: general protection fault: 0000 [#1] SMP DEBUG_PAGEALLOC
Oct 28 22:04:30 klimt kernel: Modules linked in: cts rpcsec_gss_krb5 iTCO_wdt iTCO_vendor_support sb_edac edac_core x86_pkg_temp_thermal intel_powerclamp coretemp kvm_intel kvm btrfs irqbypass crct10dif_pclmul crc32_pclmul ghash_clmulni_intel aesni_intel lrw gf128mul glue_helper ablk_helper cryptd xor pcspkr raid6_pq i2c_i801 i2c_smbus lpc_ich mfd_core sg mei_me mei ioatdma shpchp wmi ipmi_si ipmi_msghandler rpcrdma ib_ipoib rdma_ucm acpi_power_meter acpi_pad ib_ucm ib_uverbs ib_umad rdma_cm ib_cm iw_cm nfsd auth_rpcgss nfs_acl lockd grace sunrpc ip_tables xfs libcrc32c mlx4_ib mlx4_en ib_core sr_mod cdrom sd_mod ast drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops ttm drm crc32c_intel igb ahci libahci ptp mlx4_core pps_core dca libata i2c_algo_bit i2c_core dm_mirror dm_region_hash dm_log dm_mod
Oct 28 22:04:30 klimt kernel: CPU: 7 PID: 1558 Comm: nfsd Not tainted
4.9.0-rc2-00005-g82cd754 #8
Oct 28 22:04:30 klimt kernel: Hardware name: Supermicro Super Server/X10SRL-F, BIOS 1.0c 09/09/2015
Oct 28 22:04:30 klimt kernel: task:
ffff880835c3a100 task.stack:
ffff8808420d8000
Oct 28 22:04:30 klimt kernel: RIP: 0010:[<
ffffffffa05a759f>] [<
ffffffffa05a759f>] release_lock_stateid+0x1f/0x60 [nfsd]
Oct 28 22:04:30 klimt kernel: RSP: 0018:
ffff8808420dbce0 EFLAGS:
00010246
Oct 28 22:04:30 klimt kernel: RAX:
ffff88084e6660f0 RBX:
ffff88084e667020 RCX:
0000000000000000
Oct 28 22:04:30 klimt kernel: RDX:
0000000000000007 RSI:
0000000000000000 RDI:
ffff88084e667020
Oct 28 22:04:30 klimt kernel: RBP:
ffff8808420dbcf8 R08:
0000000000000001 R09:
0000000000000000
Oct 28 22:04:30 klimt kernel: R10:
ffff880835c3a100 R11:
ffff880835c3aca8 R12:
6b6b6b6b6b6b6b6b
Oct 28 22:04:30 klimt kernel: R13:
ffff88084e6670d8 R14:
ffff880835f546f0 R15:
ffff880835f1c548
Oct 28 22:04:30 klimt kernel: FS:
0000000000000000(0000) GS:
ffff88087bdc0000(0000) knlGS:
0000000000000000
Oct 28 22:04:30 klimt kernel: CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
Oct 28 22:04:30 klimt kernel: CR2:
00007ff020389000 CR3:
0000000001c06000 CR4:
00000000001406e0
Oct 28 22:04:30 klimt kernel: Stack:
Oct 28 22:04:30 klimt kernel:
ffff88084e667020 0000000000000000 ffff88084e6670d8 ffff8808420dbd20
Oct 28 22:04:30 klimt kernel:
ffffffffa05ac80d ffff880835f54548 ffff88084e640008 ffff880835f545b0
Oct 28 22:04:30 klimt kernel:
ffff8808420dbd70 ffffffffa059803d ffff880835f1c768 0000000000000870
Oct 28 22:04:30 klimt kernel: Call Trace:
Oct 28 22:04:30 klimt kernel: [<
ffffffffa05ac80d>] nfsd4_free_stateid+0xfd/0x1b0 [nfsd]
Oct 28 22:04:30 klimt kernel: [<
ffffffffa059803d>] nfsd4_proc_compound+0x40d/0x690 [nfsd]
Oct 28 22:04:30 klimt kernel: [<
ffffffffa0583114>] nfsd_dispatch+0xd4/0x1d0 [nfsd]
Oct 28 22:04:30 klimt kernel: [<
ffffffffa047bbf9>] svc_process_common+0x3d9/0x700 [sunrpc]
Oct 28 22:04:30 klimt kernel: [<
ffffffffa047ca64>] svc_process+0xf4/0x330 [sunrpc]
Oct 28 22:04:30 klimt kernel: [<
ffffffffa05827ca>] nfsd+0xfa/0x160 [nfsd]
Oct 28 22:04:30 klimt kernel: [<
ffffffffa05826d0>] ? nfsd_destroy+0x170/0x170 [nfsd]
Oct 28 22:04:30 klimt kernel: [<
ffffffff810b367b>] kthread+0x10b/0x120
Oct 28 22:04:30 klimt kernel: [<
ffffffff810b3570>] ? kthread_stop+0x280/0x280
Oct 28 22:04:30 klimt kernel: [<
ffffffff8174e8ba>] ret_from_fork+0x2a/0x40
Oct 28 22:04:30 klimt kernel: Code: c3 66 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 55 48 89 e5 41 55 41 54 53 48 8b 87 b0 00 00 00 48 89 fb 4c 8b a0 98 00 00 00 <49> 8b 44 24 20 48 8d b8 80 03 00 00 e8 10 66 1a e1 48 89 df e8
Oct 28 22:04:30 klimt kernel: RIP [<
ffffffffa05a759f>] release_lock_stateid+0x1f/0x60 [nfsd]
Oct 28 22:04:30 klimt kernel: RSP <
ffff8808420dbce0>
Oct 28 22:04:30 klimt kernel: ---[ end trace
cf5d0b371973e167 ]---
Jeff Layton says:
> Hm...now that I look though, this is a little suspicious:
>
> struct nfs4_openowner *oo = openowner(stp->st_openstp->st_stateowner);
>
> I wonder if it's possible for the openstateid to have already been
> destroyed at this point.
>
> We might be better off doing something like this to get the client pointer:
>
> stp->st_stid.sc_client;
>
> ...which should be more direct and less dependent on other stateids
> staying valid.
With the suggested change, I am no longer able to reproduce the above oops.
v2: Fix unhash_lock_stateid() as well
Fix-suggested-by: Jeff Layton <jlayton@redhat.com>
Fixes: 42691398be08 ('nfsd: Fix race between FREE_STATEID and LOCK')
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Chuck Lever [Sat, 29 Oct 2016 02:22:33 +0000 (22:22 -0400)]
svcrdma: backchannel cannot share a page for send and rcv buffers
The underlying transport releases the page pointed to by rq_buffer
during xprt_rdma_bc_send_request. When the backchannel reply arrives,
rq_rbuffer then points to freed memory.
Fixes: 68778945e46f ('SUNRPC: Separate buffer pointers for RPC ...')
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Cc: Jeff Layton <jlayton@redhat.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Jason Gunthorpe [Wed, 19 Oct 2016 21:03:41 +0000 (15:03 -0600)]
gpio/mvebu: Use irq_domain_add_linear
This fixes the irq allocation in this driver to not print:
irq: Cannot allocate irq_descs @ IRQ34, assuming pre-allocated
irq: Cannot allocate irq_descs @ IRQ66, assuming pre-allocated
Which happens because the driver already called irq_alloc_descs()
and so the change to use irq_domain_add_simple resulted in calling
irq_alloc_descs() twice.
Modernize the irq allocation in this driver to use the
irq_domain_add_linear flow directly and eliminate the use of
irq_domain_add_simple/legacy
Fixes: ce931f571b6d ("gpio/mvebu: convert to use irq_domain_add_simple()")
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Andy Lutomirski [Mon, 31 Oct 2016 15:11:43 +0000 (08:11 -0700)]
fork: Add task stack refcounting sanity check and prevent premature task stack freeing
If something goes wrong with task stack refcounting and a stack
refcount hits zero too early, warn and leak it rather than
potentially freeing it early (and silently).
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/f29119c783a9680a4b4656e751b6123917ace94b.1477926663.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Peter Wu [Mon, 31 Oct 2016 22:48:22 +0000 (23:48 +0100)]
drm/nouveau/acpi: fix check for power resources support
Check whether the kernel really supports power resources for a device,
otherwise the power might not be removed when the device is runtime
suspended (DSM should still work in these cases where PR does not).
This is a workaround for a problem where ACPICA and Windows 10 differ in
behavior. ACPICA does not correctly enumerate power resources within a
conditional block (due to delayed execution of such blocks) and as a
result power_resources is set to false even if _PR3 exists.
Fixes: 692a17dcc292 ("drm/nouveau/acpi: fix lockup with PCIe runtime PM")
Link: https://bugs.freedesktop.org/show_bug.cgi?id=98398
Reported-and-tested-by: Rick Kerkhof <rick.2889@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Peter Wu <peter@lekensteyn.nl>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Mon, 31 Oct 2016 23:05:54 +0000 (09:05 +1000)]
Merge branch 'drm-fixes-staging' of ssh://people.freedesktop.org/~/linux into drm-fixes
Pull the staging fixes tree I had into rc3 to make real -fixes again.
Masahiro Yamada [Tue, 25 Oct 2016 01:47:44 +0000 (10:47 +0900)]
gpio: of: fix GPIO drivers with multiple gpio_chip for a single node
Sylvain Lemieux reports the LPC32xx GPIO driver is broken since
commit
762c2e46c059 ("gpio: of: remove of_gpiochip_and_xlate() and
struct gg_data"). Probably, gpio-etraxfs.c and gpio-davinci.c are
broken too.
Those drivers register multiple gpio_chip that are associated to a
single OF node, and their own .of_xlate() checks if the passed
gpio_chip is valid.
Now, the problem is of_find_gpiochip_by_node() returns the first
gpio_chip found to match the given node. So, .of_xlate() fails,
except for the first GPIO bank.
Reverting the commit could be a solution, but I do not want to go
back to the mess of struct gg_data. Another solution here is to
take the match by a node pointer and the success of .of_xlate().
It is a bit clumsy to call .of_xlate twice; for gpio_chip matching
and for really getting the gpio_desc index. Perhaps, our long-term
goal might be to convert the drivers to single chip registration,
but this commit will solve the problem until then.
Fixes: 762c2e46c059 ("gpio: of: remove of_gpiochip_and_xlate() and struct gg_data")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reported-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Tested-by: David Lechner <david@lechnology.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Lars-Peter Clausen [Mon, 24 Oct 2016 11:59:15 +0000 (13:59 +0200)]
gpio: GPIO_GET_LINE{HANDLE,EVENT}_IOCTL: Fix file descriptor leak
When allocating a new line handle or event a file is allocated that it is
associated to. The file is attached to a file descriptor of the current
process and the file descriptor is returned to userspace using
copy_to_user(). If this copy operation fails the line handle or event
allocation is aborted, all acquired resources are freed and an error is
returned.
But the file struct is not freed and left attached to the userspace
application and even though the file descriptor number was not copied it is
trivial to guess. If a userspace application performs a IOCTL on such a
left over file descriptor it will trigger a use-after-free and if the file
descriptor is closed (latest when the application exits) a double-free is
triggered.
anon_inode_getfd() performs 3 tasks, allocate a file struct, allocate a
file descriptor for the current process and install the file struct in the
file descriptor. As soon as the file struct is installed in the file
descriptor it is accessible by userspace (even if the IOCTL itself hasn't
completed yet), this means uninstalling the fd on the error path is not an
option, since userspace might already got a reference to the file.
Instead anon_inode_getfd() needs to be broken into its individual steps.
The allocation of the file struct and file descriptor is done first, then
the copy_to_user() is executed and only if it succeeds the file is
installed.
Since the file struct is reference counted it can not be just freed, but
its reference needs to be dropped, which will also call the release()
callback, which will free the state attached to the file. So in this case
the normal error cleanup path should not be taken.
Cc: stable@vger.kernel.org
Fixes: d932cd49182f ("gpio: free handles in fringe cases")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Torvalds [Mon, 31 Oct 2016 18:54:11 +0000 (11:54 -0700)]
Merge tag 'spi-fix-v4.9-rc3' of git://git./linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown: "A few small fixes for SPI, one core fix
that only applies in cases where we're handling DT overlays and a
couple of driver specific fixes:
- Fix handling of error cases when instantiating DT overlays so we
don't end up just ignoring devices that encountered an error during
instantiation.
- Avoid reading uninitialized data when handing spurious interrupts
in the espi driver.
- A driver specific fix for the dspi driver to fix a bad interaction
with u-boot"
* tag 'spi-fix-v4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: dspi: clear SPI_SR before enable interrupt
spi: fsl-espi: avoid processing uninitalized data on error
spi: mark device nodes only in case of successful instantiation
Kees Cook [Tue, 18 Oct 2016 22:08:04 +0000 (00:08 +0200)]
latent_entropy: Fix wrong gcc code generation with 64 bit variables
The stack frame size could grow too large when the plugin used long long
on 32-bit architectures when the given function had too many basic blocks.
The gcc warning was:
drivers/pci/hotplug/ibmphp_ebda.c: In function 'ibmphp_access_ebda':
drivers/pci/hotplug/ibmphp_ebda.c:409:1: warning: the frame size of 1108 bytes is larger than 1024 bytes [-Wframe-larger-than=]
This switches latent_entropy from u64 to unsigned long.
Thanks to PaX Team and Emese Revfy for the patch.
Signed-off-by: Kees Cook <keescook@chromium.org>
Kees Cook [Mon, 31 Oct 2016 17:40:13 +0000 (10:40 -0700)]
gcc-plugins: Export symbols needed by gcc
This explicitly exports symbols that gcc expects from plugins.
Based on code from Emese Revfy.
Signed-off-by: Kees Cook <keescook@chromium.org>
Linus Torvalds [Mon, 31 Oct 2016 17:14:09 +0000 (10:14 -0700)]
Merge tag 'regulator-fix-v4.9-rc3' of git://git./linux/kernel/git/broonie/regulator
Pull regulator fix from Mark Brown:
"Fix ramp_delay warnings for v4.9
A new warning was introduced for missing information about the time
that regulators take to power on in v4.9. This is in theory a real
issue but for most practical regulators the communication overhead of
talking to the device is greater than the ramp time so a lot of
drivers don't set it and the warning is far too noisy without
identifying practical issues.
Just remove the warning for now"
* tag 'regulator-fix-v4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: core: silence warning: "VDD1: ramp_delay not set"
Linus Torvalds [Mon, 31 Oct 2016 17:12:35 +0000 (10:12 -0700)]
Merge tag 'regmap-fix-v4.9-rc3' of git://git./linux/kernel/git/broonie/regmap
Pull regmap fixes from Mark Brown:
"A couple of small build fixes here, nothing major.
The missing include is triggered in some configurations and the
renaming of ret is defensive for the benefit of some drivers people
are in the process of mainlining"
* tag 'regmap-fix-v4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: Rename ret variable in regmap_read_poll_timeout
regmap: include <linux/delay.h> from include/linux/regmap.h
Linus Torvalds [Mon, 31 Oct 2016 17:10:26 +0000 (10:10 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/jmorris/linux-security
Pull TPM fix from James Morris.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
tpm: remove invalid min length check from tpm_do_selftest()
Jarkko Sakkinen [Tue, 4 Oct 2016 06:49:47 +0000 (09:49 +0300)]
tpm: remove invalid min length check from tpm_do_selftest()
Removal of this check was not properly amended to the original commit.
Cc: stable@vger.kernel.org
Fixes: 0c541332231e ("tpm: use tpm_pcr_read_dev() in tpm_do_selftest()")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
Linus Torvalds [Mon, 31 Oct 2016 15:10:38 +0000 (08:10 -0700)]
Merge branch 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm
Pull ARM fixes from Russell King:
"A fix for a regression on ARMv4T CPUs, and wiring up the new pkey
syscalls for ARM"
* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: wire up new pkey syscalls
ARM: fix oops when using older ARMv4T CPUs
Linus Torvalds [Mon, 31 Oct 2016 15:03:56 +0000 (08:03 -0700)]
Merge git://git./linux/kernel/git/davem/sparc
Pull sparc fixes from David Miller:
"Several sparc64 bug fixes here:
1) Make the user copy routines on sparc64 return a properly accurate
residual length when an exception occurs.
2) We can get enormous kernel TLB range flush requests from vmalloc
unmaps, so handle these more gracefully by doing full flushes
instead of going page-by-page.
3) Cope properly with negative branch offsets in sparc jump-label
support, from James Clarke.
4) Some old-style decl GCC warning fixups from Tobias Klauser"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: Handle extremely large kernel TLB range flushes more gracefully.
sparc64: Fix illegal relative branches in hypervisor patched TLB cross-call code.
sparc64: Fix instruction count in comment for __hypervisor_flush_tlb_pending.
sparc64: Handle extremely large kernel TSB range flushes sanely.
sparc: Handle negative offsets in arch_jump_label_transform
sparc64: Fix illegal relative branches in hypervisor patched TLB code.
sparc64: Delete now unused user copy fixup functions.
sparc64: Delete now unused user copy assembler helpers.
sparc64: Convert U3copy_{from,to}_user to accurate exception reporting.
sparc64: Convert NG2copy_{from,to}_user to accurate exception reporting.
sparc64: Convert NGcopy_{from,to}_user to accurate exception reporting.
sparc64: Convert NG4copy_{from,to}_user to accurate exception reporting.
sparc64: Convert U1copy_{from,to}_user to accurate exception reporting.
sparc64: Convert GENcopy_{from,to}_user to accurate exception reporting.
sparc64: Convert copy_in_user to accurate exception reporting.
sparc64: Prepare to move to more saner user copy exception handling.
sparc64: Delete __ret_efault.
sparc32: Fix old style declaration GCC warnings
sparc64: Fix old style declaration GCC warnings
sparc64: Setup a scheduling domain for highest level cache.
Miklos Szeredi [Mon, 31 Oct 2016 13:42:14 +0000 (14:42 +0100)]
ovl: fsync after copy-up
Make sure the copied up file hits the disk before renaming to the final
destination. If this is not done then the copy-up may corrupt the data in
the file in case of a crash.
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Cc: <stable@vger.kernel.org>
Miklos Szeredi [Mon, 31 Oct 2016 13:42:14 +0000 (14:42 +0100)]
ovl: fix get_acl() on tmpfs
tmpfs doesn't have ->get_acl() because it only uses cached acls.
This fixes the acl tests in pjdfstest when tmpfs is used as the upper layer
of the overlay.
Reported-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Fixes: 39a25b2b3762 ("ovl: define ->get_acl() for overlay inodes")
Cc: <stable@vger.kernel.org> # v4.8
Miklos Szeredi [Mon, 31 Oct 2016 13:42:14 +0000 (14:42 +0100)]
ovl: update S_ISGID when setting posix ACLs
This change fixes xfstest generic/375, which failed to clear the
setgid bit in the following test case on overlayfs:
touch $testfile
chown 100:100 $testfile
chmod 2755 $testfile
_runas -u 100 -g 101 -- setfacl -m u::rwx,g::rwx,o::rwx $testfile
Reported-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Tested-by: Amir Goldstein <amir73il@gmail.com>
Fixes: d837a49bd57f ("ovl: fix POSIX ACL setting")
Cc: <stable@vger.kernel.org> # v4.8
Michael S. Tsirkin [Sun, 30 Oct 2016 22:38:21 +0000 (00:38 +0200)]
virtio_ring: mark vring_dma_dev inline
This inline function is unused on configurations
where dma_map/unmap are empty macros.
Make the function inline to avoid gcc errors because
of an unused static function.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Michael S. Tsirkin [Sun, 14 Aug 2016 17:57:14 +0000 (20:57 +0300)]
virtio/vhost: add Jason to list of maintainers
Jason's been one of the mst active contributors
to virtio and vhost, it will help to formalize this
and list him as co-maintainer.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Markus Elfring [Tue, 13 Sep 2016 11:43:50 +0000 (13:43 +0200)]
virtio_blk: Delete an unnecessary initialisation in init_vq()
The local variable "err" will be set to an appropriate value
by a following statement.
Thus omit the explicit initialisation at the beginning.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Markus Elfring [Tue, 13 Sep 2016 09:32:22 +0000 (11:32 +0200)]
virtio_blk: Use kmalloc_array() in init_vq()
Multiplications for the size determination of memory allocations
indicated that array data structures should be processed.
Thus use the corresponding function "kmalloc_array".
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Juergen Gross [Tue, 11 Oct 2016 09:02:14 +0000 (11:02 +0200)]
virtio: remove config.c
Remove unused file config.c
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Matt Redfearn [Tue, 11 Oct 2016 11:05:15 +0000 (12:05 +0100)]
virtio: console: Unlock vqs while freeing buffers
Commit
c6017e793b93 ("virtio: console: add locks around buffer removal
in port unplug path") added locking around the freeing of buffers in the
vq. However, when free_buf() is called with can_sleep = true and rproc
is enabled, it calls dma_free_coherent() directly, requiring interrupts
to be enabled. Currently a WARNING is triggered due to the spin locking
around free_buf, with a call stack like this:
WARNING: CPU: 3 PID: 121 at ./include/linux/dma-mapping.h:433
free_buf+0x1a8/0x288
Call Trace:
[<
8040c538>] show_stack+0x74/0xc0
[<
80757240>] dump_stack+0xd0/0x110
[<
80430d98>] __warn+0xfc/0x130
[<
80430ee0>] warn_slowpath_null+0x2c/0x3c
[<
807e7c6c>] free_buf+0x1a8/0x288
[<
807ea590>] remove_port_data+0x50/0xac
[<
807ea6a0>] unplug_port+0xb4/0x1bc
[<
807ea858>] virtcons_remove+0xb0/0xfc
[<
807b6734>] virtio_dev_remove+0x58/0xc0
[<
807f918c>] __device_release_driver+0xac/0x134
[<
807f924c>] device_release_driver+0x38/0x50
[<
807f7edc>] bus_remove_device+0xfc/0x130
[<
807f4b74>] device_del+0x17c/0x21c
[<
807f4c38>] device_unregister+0x24/0x38
[<
807b6b50>] unregister_virtio_device+0x28/0x44
Fix this by restructuring the loops to allow the locks to only be taken
where it is necessary to protect the vqs, and release it while the
buffer is being freed.
Fixes: c6017e793b93 ("virtio: console: add locks around buffer removal in port unplug path")
Cc: stable@vger.kernel.org
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Paolo Bonzini [Thu, 6 Oct 2016 09:39:12 +0000 (11:39 +0200)]
ringtest: poll for new buffers once before updating event index
Updating the event index has a memory barrier and causes more work
on the other side to actually signal the event. It is unnecessary
if a new buffer has already appeared on the ring, so poll once before
doing the update.
The effect of this on the 0.9 ring implementation is pretty much
invisible, but on the new-style ring it provides a consistent 3%
performance improvement.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Paolo Bonzini [Thu, 6 Oct 2016 09:39:11 +0000 (11:39 +0200)]
ringtest: commonize implementation of poll_avail/poll_used
Provide new primitives used_empty/avail_empty and
build poll_avail/poll_used on top of it.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Paolo Bonzini [Thu, 6 Oct 2016 09:39:10 +0000 (11:39 +0200)]
ringtest: use link-time optimization
By using -flto and -fwhole-program, all functions from the ring implementation
can be treated as static and possibly inlined. Force this to happen through
the GCC flatten attribute.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Konstantin Neumoin [Thu, 29 Sep 2016 10:17:12 +0000 (13:17 +0300)]
virtio: update balloon size in balloon "probe"
The following commit '
fad7b7b27b6a (virtio_balloon: Use a workqueue
instead of "vballoon" kthread)' has added a regression. Original code with
kthread starts the thread inside probe and checks the necessity to update
balloon inside the thread immediately.
Nowadays the code behaves differently. Work is queued only on the first
command from the host after the negotiation. Thus there is a window
especially at the guest startup or the module reloading when the balloon
size is not updated until the notification from the host.
This patch adds balloon size check at the end of the probe to match
original behaviour.
Signed-off-by: Konstantin Neumoin <kneumoin@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Ladi Prosek [Wed, 31 Aug 2016 12:00:04 +0000 (14:00 +0200)]
virtio_ring: Make interrupt suppression spec compliant
According to the spec, if the VIRTIO_RING_F_EVENT_IDX feature bit is
negotiated the driver MUST set flags to 0. Not dirtying the available
ring in virtqueue_disable_cb also has a minor positive performance
impact, improving L1 dcache load missed by ~0.5% in vring_bench.
Writes to the used event field (vring_used_event) are still unconditional.
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: <stable@vger.kernel.org> # f277ec4 virtio_ring: shadow available
Cc: <stable@vger.kernel.org>
Signed-off-by: Ladi Prosek <lprosek@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Will Deacon [Wed, 14 Sep 2016 16:33:26 +0000 (17:33 +0100)]
virtio_pci: Limit DMA mask to 44 bits for legacy virtio devices
Legacy virtio defines the virtqueue base using a 32-bit PFN field, with
a read-only register indicating a fixed page size of 4k.
This can cause problems for DMA allocators that allocate top down from
the DMA mask, which is set to 64 bits. In this case, the addresses are
silently truncated to 44-bit, leading to IOMMU faults, failure to read
from the queue or data corruption.
This patch restricts the coherent DMA mask for legacy PCI virtio devices
to 44 bits, which matches the specification.
Cc: stable@vger.kernel.org
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Benjamin Serebrin <serebrin@google.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Linus Torvalds [Sun, 30 Oct 2016 03:33:20 +0000 (20:33 -0700)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
"Lots of fixes, mostly drivers as is usually the case.
1) Don't treat zero DMA address as invalid in vmxnet3, from Alexey
Khoroshilov.
2) Fix element timeouts in netfilter's nft_dynset, from Anders K.
Pedersen.
3) Don't put aead_req crypto struct on the stack in mac80211, from
Ard Biesheuvel.
4) Several uninitialized variable warning fixes from Arnd Bergmann.
5) Fix memory leak in cxgb4, from Colin Ian King.
6) Fix bpf handling of VLAN header push/pop, from Daniel Borkmann.
7) Several VRF semantic fixes from David Ahern.
8) Set skb->protocol properly in ip6_tnl_xmit(), from Eli Cooper.
9) Socket needs to be locked in udp_disconnect(), from Eric Dumazet.
10) Div-by-zero on 32-bit fix in mlx4 driver, from Eugenia Emantayev.
11) Fix stale link state during failover in NCSCI driver, from Gavin
Shan.
12) Fix netdev lower adjacency list traversal, from Ido Schimmel.
13) Propvide proper handle when emitting notifications of filter
deletes, from Jamal Hadi Salim.
14) Memory leaks and big-endian issues in rtl8xxxu, from Jes Sorensen.
15) Fix DESYNC_FACTOR handling in ipv6, from Jiri Bohac.
16) Several routing offload fixes in mlxsw driver, from Jiri Pirko.
17) Fix broadcast sync problem in TIPC, from Jon Paul Maloy.
18) Validate chunk len before using it in SCTP, from Marcelo Ricardo
Leitner.
19) Revert a netns locking change that causes regressions, from Paul
Moore.
20) Add recursion limit to GRO handling, from Sabrina Dubroca.
21) GFP_KERNEL in irq context fix in ibmvnic, from Thomas Falcon.
22) Avoid accessing stale vxlan/geneve socket in data path, from
Pravin Shelar"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (189 commits)
geneve: avoid using stale geneve socket.
vxlan: avoid using stale vxlan socket.
qede: Fix out-of-bound fastpath memory access
net: phy: dp83848: add dp83822 PHY support
enic: fix rq disable
tipc: fix broadcast link synchronization problem
ibmvnic: Fix missing brackets in init_sub_crq_irqs
ibmvnic: Fix releasing of sub-CRQ IRQs in interrupt context
Revert "ibmvnic: Fix releasing of sub-CRQ IRQs in interrupt context"
arch/powerpc: Update parameters for csum_tcpudp_magic & csum_tcpudp_nofold
net/mlx4_en: Save slave ethtool stats command
net/mlx4_en: Fix potential deadlock in port statistics flow
net/mlx4: Fix firmware command timeout during interrupt test
net/mlx4_core: Do not access comm channel if it has not yet been initialized
net/mlx4_en: Fix panic during reboot
net/mlx4_en: Process all completions in RX rings after port goes up
net/mlx4_en: Resolve dividing by zero in 32-bit system
net/mlx4_core: Change the default value of enable_qos
net/mlx4_core: Avoid setting ports to auto when only one port type is supported
net/mlx4_core: Fix the resource-type enum in res tracker to conform to FW spec
...
pravin shelar [Fri, 28 Oct 2016 16:59:16 +0000 (09:59 -0700)]
geneve: avoid using stale geneve socket.
This patch is similar to earlier vxlan patch.
Geneve device close operation frees geneve socket. This
operation can race with geneve-xmit function which
dereferences geneve socket. Following patch uses RCU
mechanism to avoid this situation.
Signed-off-by: Pravin B Shelar <pshelar@ovn.org>
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pravin shelar [Fri, 28 Oct 2016 16:59:15 +0000 (09:59 -0700)]
vxlan: avoid using stale vxlan socket.
When vxlan device is closed vxlan socket is freed. This
operation can race with vxlan-xmit function which
dereferences vxlan socket. Following patch uses RCU
mechanism to avoid this situation.
Signed-off-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mintz, Yuval [Sat, 29 Oct 2016 14:04:35 +0000 (17:04 +0300)]
qede: Fix out-of-bound fastpath memory access
Driver allocates a shadow array for transmitted SKBs with X entries;
That means valid indices are {0,...,X - 1}. [X == 8191]
Problem is the driver also uses X as a mask for a
producer/consumer in order to choose the right entry in the
array which allows access to entry X which is out of bounds.
To fix this, simply allocate X + 1 entries in the shadow array.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Roger Quadros [Fri, 28 Oct 2016 09:40:20 +0000 (12:40 +0300)]
net: phy: dp83848: add dp83822 PHY support
This PHY has a compatible register set with DP83848x so
add support for it.
Acked-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Govindarajulu Varadarajan [Thu, 27 Oct 2016 23:01:03 +0000 (16:01 -0700)]
enic: fix rq disable
When MTU is changed from 9000 to 1500 while there is burst of inbound 9000
bytes packets, adaptor sometimes delivers 9000 bytes packets to 1500 bytes
buffers. This causes memory corruption and sometimes crash.
This is because of a race condition in adaptor between "RQ disable"
clearing descriptor mini-cache and mini-cache valid bit being set by
completion of descriptor fetch. This can result in stale RQ desc being
cached and used when packets arrive. In this case, the stale descriptor
have old MTU value.
Solution is to write RQ->disable twice. The first write will stop any
further desc fetches, allowing the second disable to clear the mini-cache
valid bit without danger of a race.
Also, the check for rq->running becoming 0 after writing rq->enable to 0
is not done properly. When incoming packets are flooding the interface,
rq->running will pulse high for each dropped packet. Since the driver was
waiting for 10us between each poll, it is possible to see rq->running = 1
1000 times in a row, even though it is not actually stuck running.
This results in false failure of vnic_rq_disable(). Fix is to try more
than 1000 time without delay between polls to ensure we do not miss when
running goes low.
In old adaptors rq->enable needs to be re-written to 0 when posted_index
is reset in vnic_rq_clean() in order to keep rq->prefetch_index in sync.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
projects / openwrt / staging / blogic.git / log