John Audia [Wed, 5 Apr 2023 15:56:48 +0000 (11:56 -0400)]
kernel: bump 5.10 to 5.10.177
All patches automatically rebased.
Signed-off-by: John Audia <therealgraysky@proton.me>
[Refresh patches on openwrt-22.03 branch]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit
78a468f690a0f3052ff68ef33910705b25bac33d)
Felix Baumann [Fri, 21 Apr 2023 01:39:38 +0000 (03:39 +0200)]
ramips: mt7621: add support for Cudy X6 v2
Rename existing device to v1 and create common .dtsi
Difference to v1: 16MB Flash
Specifications:
SoC: MediaTek MT7621
RAM: 256 MB
Flash: 16 MB (SPI NOR, XM25QH128C on my device)
WiFi: MediaTek MT7915E
Switch: 1 WAN, 4 LAN (Gigabit)
Buttons: Reset, WPS
LEDs: Two Power LEDs (blue and red; together they form purple)
Power: DC 12V 1A center positive
Serial: 115200 8N1
C440 - (3V3 - GND - RX - TX) - C41 | v1 and v2
(P - G - R - T) | v2 labels them on the board
Installation:
Download and flash the manufacturer's built OpenWrt image available at
http://www.cudytech.com/openwrt_software_download
Install the new OpenWrt image via luci (System -> Backup/Flash firmware)
Be sure to NOT keep settings.
Recovery:
Loads only signed manufacture firmware due to bootloader RSA verification
Serve tftp-recovery image as /recovery.bin on 192.168.1.88/24
Connect to any lan ethernet port
Power on the device while holding the reset button
Wait at least 8 seconds before releasing reset button for image to
download
MAC addresses as verified by OEM firmware:
use address source
LAN f4:a4:54:86:75:a2 label
WAN f4:a4:54:86:75:a3 label + 1
2g f4:a4:54:86:75:a2 label
5g f6:a4:54:b6:75:a2 label + LA-Bit set + 4th oktet increased
The label MAC address is found in bdinfo 0xde00.
Signed-off-by: Felix Baumann <felix.bau@gmx.de>
(cherry picked from commit
e38de40f8dd350344407fe5a91e81191f6960804)
Felix Baumann [Fri, 21 Apr 2023 01:07:58 +0000 (03:07 +0200)]
ramips: Cudy X6 fixes / improvements
- Correct WiFi MACs, they didn't match oem firmware
- Move nvmem-cells to bdinfo partition and remove &bdinfo reference
- Add OEM device model name R13 to SUPPORTED_DEVICES
This allows sysupgrading from Cudy's OpenWrt fork without force
- Label red_led and use it during failsafe mode and upgrades
MAC addresses as verified by OEM firmware:
use address source
LAN b4:4b:d6:2d:c8:4a label
WAN b4:4b:d6:2d:c8:4b label + 1
2g b4:4b:d6:2d:c8:4a label
5g b6:4b:d6:3d:c8:4a label + LA-Bit set + 4th oktet increased
The label MAC address is found in bdinfo 0xde00.
Signed-off-by: Felix Baumann <felix.bau@gmx.de>
[read wifi mac from flash offset]
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit
45cf200b2e22c34f2ae043b87e24230de526fefc)
Hauke Mehrtens [Thu, 27 Apr 2023 21:05:29 +0000 (23:05 +0200)]
OpenWrt v22.03.5: revert to branch defaults
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Thu, 27 Apr 2023 21:05:23 +0000 (23:05 +0200)]
OpenWrt v22.03.5: adjust config defaults
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
David Bauer [Thu, 27 Apr 2023 20:24:15 +0000 (22:24 +0200)]
ramips: reduce Archer AX23 / MR70X SPI-frequency
It was brought to attention the Archer AX23 v1 fails to read jffs2 data
from time to time. While this is not reproducible on my unit, it is on
others.
Reducing the SPI frequency does the trick. While it worked with at lest
40 MHz, opt for the cautious side and choose a save frequency of 25 MHz.
Apply the same treatment to the Mercusys MR70X which uses a similar
design just in case.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit
2c530fcb972c112e7a2b10f9c21ac6d276624b5e)
Nick Hainke [Sun, 28 Aug 2022 13:00:54 +0000 (15:00 +0200)]
ccache: update to 4.6.3
Release Notes:
https://ccache.dev/releasenotes.html#_ccache_4_6_3
Refresh patch:
- 100-honour-copts.patch
Signed-off-by: Nick Hainke <vincent@systemli.org>
(cherry picked from commit
83ea2e11b4b7872642bc7ac587361ccd783308f2)
Nick Hainke [Wed, 24 Aug 2022 08:57:35 +0000 (10:57 +0200)]
tools/ccache: update to 4.6.2
Release notes:
https://ccache.dev/releasenotes.html#_ccache_4_6_2
Signed-off-by: Nick Hainke <vincent@systemli.org>
(cherry picked from commit
ac61cf596cc4cdfb93981361b093c1d97e4a1b96)
Nick Hainke [Thu, 18 Aug 2022 05:53:00 +0000 (07:53 +0200)]
tools/ccache: update to 4.6.1
Release notes:
https://ccache.dev/releasenotes.html#_ccache_4_6_1
Signed-off-by: Nick Hainke <vincent@systemli.org>
(cherry picked from commit
2e87e24e43c49565e23643eb6eceef8455434647)
Haoan Li [Wed, 5 Apr 2023 18:42:15 +0000 (02:42 +0800)]
ramips: fix lzma-loader for buffalo_WSR_600DHP
This fixes a well known "LZMA ERROR 1" error, reported previously on
numerous of similar devices.
Fixes: #11919
Signed-off-by: Haoan Li <lihaoan1001@163.com>
(cherry picked from commit
c7b484f3647c58da2f86395228a9927290a6f6ed)
David Bauer [Mon, 17 Apr 2023 17:15:22 +0000 (19:15 +0200)]
ath79: create Aruba AP-105 APBoot compatible image
Alter the Aruba AP-105 image generation process so OpenWrt can be loaded
with the vendor Aruba APBoot.
This works by prepending the OpenWrt LZMA loader to the uImage and
jumping directly to the loader. Aruba does not offer bootm on these
boards.
This approach keeps compatibility to devices which had their U-Boot
replaced. Both bootloaders can boot the same image.
The same modification is most likely also possible for the Aruba AP-175.
With this patch, new installations do not require replacing the
bootloader and can be performed from the serial console without opening
the case.
Installation
------------
1. Attach to the serial console of the AP-105.
Interrupt autoboot and change the U-Boot env.
$ setenv apb_rb_openwrt "setenv ipaddr 192.168.1.1;
setenv serverip 192.168.1.66;
netget 0x84000000 ap105.bin; go 0x84000040"
$ setenv apb_fb_openwrt "cp.b 0xbf040000 0x84000000 0x10000;
go 0x84000040"
$ setenv bootcmd "run apb_fb_openwrt"
$ saveenv
2. Load the OpenWrt initramfs image on the device using TFTP.
Place the initramfs image as "ap105.bin" in the TFTP server
root directory, connect it to the AP and make the server reachable
at 192.168.1.66/24.
$ run apb_rb_openwrt
3. Once OpenWrt booted, transfer the sysupgrade image to the device
using scp and use sysupgrade to install the firmware.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit
e11d00d44c66b1534fbc399fda55951cd0a2168a)
Eneas U de Queiroz [Tue, 4 Apr 2023 18:39:56 +0000 (15:39 -0300)]
openssl: fix CVE-2023-464 and CVE-2023-465
Apply two patches fixing low-severity vulnerabilities related to
certificate policies validation:
- Excessive Resource Usage Verifying X.509 Policy Constraints
(CVE-2023-0464)
Severity: Low
A security vulnerability has been identified in all supported versions
of OpenSSL related to the verification of X.509 certificate chains
that include policy constraints. Attackers may be able to exploit
this vulnerability by creating a malicious certificate chain that
triggers exponential use of computational resources, leading to a
denial-of-service (DoS) attack on affected systems.
Policy processing is disabled by default but can be enabled by passing
the `-policy' argument to the command line utilities or by calling the
`X509_VERIFY_PARAM_set1_policies()' function.
- Invalid certificate policies in leaf certificates are silently ignored
(CVE-2023-0465)
Severity: Low
Applications that use a non-default option when verifying certificates
may be vulnerable to an attack from a malicious CA to circumvent
certain checks.
Invalid certificate policies in leaf certificates are silently ignored
by OpenSSL and other certificate policy checks are skipped for that
certificate. A malicious CA could use this to deliberately assert
invalid certificate policies in order to circumvent policy checking on
the certificate altogether.
Policy processing is disabled by default but can be enabled by passing
the `-policy' argument to the command line utilities or by calling the
`X509_VERIFY_PARAM_set1_policies()' function.
Note: OpenSSL also released a fix for low-severity security advisory
CVE-2023-466. It is not included here because the fix only changes the
documentation, which is not built nor included in any OpenWrt package.
Due to the low-severity of these issues, there will be not be an
immediate new release of OpenSSL.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Daniel Golle [Sat, 15 Apr 2023 00:35:17 +0000 (01:35 +0100)]
kernel: backport fix for recently introduced UBI bug
Import commit "ubi: Fix failure attaching when vid_hdr offset equals to
(sub)page size" which did not yet make it to stable upstream Linux trees.
Fixes: #12232
Fixes: #12339
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit
aad34818b50029e07ed9221ae46f9770d6e29785)
Matthias Schiffer [Thu, 13 Apr 2023 18:51:05 +0000 (20:51 +0200)]
uclient: update to Git version 2023-04-13
007d94546749 uclient: cancel state change timeout in uclient_disconnect()
644d3c7e13c6 ci: improve wolfSSL test coverage
dc54d2b544a1 tests: add certificate check against letsencrypt.org
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
(cherry picked from commit
4f1c2e8deef10e9ca34ceff5a096e62aaa668e90)
Daniel Golle [Sun, 9 Apr 2023 22:35:24 +0000 (23:35 +0100)]
OpenWrt v22.03.4: revert to branch defaults
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Sun, 9 Apr 2023 22:35:19 +0000 (23:35 +0100)]
OpenWrt v22.03.4: adjust config defaults
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Paul Spooren [Sun, 12 Mar 2023 15:56:41 +0000 (16:56 +0100)]
imagebuilder: allow to specific ROOTFS_PARTSIZE
Setting this options modifies the rootfs size of created images. When
installing a large number of packages it may become necessary to
increase the size to have enough storage.
This option is only useful for supported devices, i.e. with an attached
SD Card or installed on a hard drive.
Signed-off-by: Paul Spooren <mail@aparcar.org>
(cherry picked from commit
7b7edd25a571568438c886529d3443054e02f55f)
David Bauer [Thu, 30 Mar 2023 01:51:08 +0000 (03:51 +0200)]
ramips: define remapping-range for DAP-X1860
Prevent the BBT translation layer from remapping the UBI used for
storing rootfs.
Explicitly define the number of blocks reserved for remapping.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit
076da59f17803e9412ef5e50988aff6c7e536292)
Sebastian Schaper [Sat, 7 Jan 2023 12:45:44 +0000 (13:45 +0100)]
ramips: add support for D-Link DAP-X1860 A1
The DAP-X1860 is a wall-plug AX1800 repeater.
Specifications:
- MT7621, 256 MiB RAM, 128 MiB SPI NAND
- MT7915 + MT7975 2x2 802.11ax (DBDC)
- Ethernet: 1 port 10/100/1000
- LED RSSI bargraph (2x green, 1x red/orange), status
and RSSI LEDs are incorrectly populated red/orange
(should be red/green according to documentation)
Installation:
- Keep reset button pressed during plug-in
- Web Recovery Updater is at 192.168.0.50
- Upload factory.bin, confirm flashing
(seems to work best with Chromium-based browsers)
Revert to OEM firmware:
- tar -xvf DAP-X1860_RevA_Firmware_101b94.bin
- openssl enc -d -md md5 -aes-256-cbc -in FWImage.st2 \
-out FWImage.st1 -k MB0dBx62oXJXDvt12lETWQ==
- tar -xvf FWImage.st1
- flash kernel_DAP-X1860.bin via Recovery
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
(cherry picked from commit
3c31f6b521bb5fc49e222a8f2bcd454b73452a0e)
Joe Mullally [Sun, 2 Apr 2023 18:51:21 +0000 (21:51 +0300)]
ramips: lower re305-v3 spi-max-frequency
Fix flash I/O instability observed in newer devices with cFeon
QH64A-104HIP (detected as en25qh64).
Ref: https://forum.openwrt.org/t/support-for-tp-link-re305-v3/75893/91
Reported-by: Dimitri Souza <dimitri.souza@gmail.com>
Tested-by: Dimitri Souza <dimitri.souza@gmail.com>
Signed-off-by: Joe Mullally <jwmullally@gmail.com>
[alter commit-message - target master]
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit
2122c80b321d439cf8b669ae26fcfeec605cf2cc)
Maik Goette [Sun, 8 Jan 2023 17:35:10 +0000 (18:35 +0100)]
lantiq: fix lzma-loader for Netgear DGN 3500(B)
Fixes Uncompressing Kernel Image ... ERROR: LzmaDecode.c, 561
Fixes: #11701 for both 3500(B)
Signed-off-by: Maik Goette <github@beeit.de>
(cherry picked from commit
4d9c38d654fdfb72ef641573bbf5b0f73f638f2e)
Kien Truong [Sat, 10 Sep 2022 08:25:35 +0000 (15:25 +0700)]
iproute2: add missing libbpf dependency
This patch adds libbpf to the dependencies of tc-mod-iptables.
The package tc-mod-iptables is missing libbpf as a dependency,
which leads to the build failure described in bug #9491
LIBBPF_FORCE=on set, but couldn't find a usable libbpf
The build dependency is already automatically added because some other
packages from iproute2 depend on libbpf, but bpftools has multiple build
variants. With multiple build variants none gets build by default and
the build system will not build bpftools before iproute2.
Fixes: #9491
Signed-off-by: Kien Truong <duckientruong@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit
fa468d4bcdc7e6eb84ea51d9b05368ed87c43aae)
Joe Mullally [Mon, 28 Nov 2022 20:35:39 +0000 (20:35 +0000)]
ath79: tiny: Do not build TPLink WPA8630Pv2 by default
22.03.1+ and snapshot builds no longer fit the 6M flash space
available for these models.
This disables failing buildbot image builds for these devices.
Images can still be built manually with ImageBuilder.
Signed-off-by: Joe Mullally <jwmullally@gmail.com>
(cherry picked from commit
4965cbd259bb9001e8724f53520f4be1e4723212)
John Thomson [Wed, 9 Nov 2022 23:55:11 +0000 (09:55 +1000)]
ramips: mt7621: mikrotik 760igs (hEX S) fix SFP
This device uses an AR8031/AR8033 chip to convert SoC gmac1
RGMII to 1000base-x or sgmii for the SFP fibre cage.
The SFP cage requires phy-mode rgmii-rxid, and without it will not
recieve any packets: ethtool -S sfp rx_fcs_errors will increase when
packets should be being received, but no other _rx counters will change.
Fixes: c77858aa792 ("ramips: mt7621-dts: change phy-mode of gmac1 to rgmii")
Reviewed-by: Robert Marko <robimarko@gmail.com>
Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
(cherry picked from commit
7ea965b57803ceec20222279377e611652ac217f)
Eneas U de Queiroz [Mon, 6 Mar 2023 14:58:56 +0000 (11:58 -0300)]
openssl: fix variable reference in conffiles
Fix the trivial abscence of $() when assigning engine config files to
the main libopenssl-config package even if the corresponding engines
were not built into the main library.
This is mostly cosmetic, since scripts/ipkg-build tests the file's
presence before it is actually included in the package's conffiles.
Fixes: 30b0351039 "openssl: configure engine packages during install"
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
(cherry picked from commit
c75cd5f6028da6ceb1fb3438da93e2305cd720b1)
Michael Pratt [Fri, 9 Dec 2022 20:45:04 +0000 (15:45 -0500)]
ath79: use lzma-loader for Senao initramfs images
Some vendors of Senao boards have put a bootloader
that cannot handle both large gzip or large lzma files.
There is no disadvantage by doing this for all of them.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
(cherry picked from commit
8342c092a03caedbf160d4ac3982c6a9be91261f)
Luo Chongjun [Thu, 15 Dec 2022 09:25:15 +0000 (17:25 +0800)]
ath79: Fix glinet ar300m usb not working
glinet forum users reported the problem at
https://forum.gl-inet.com/t/gl-ar300m16-openwrt-22-03-0-rc5-usb-port-power-off-by-default/23199
The current code uses the regulator framework to control the USB power
supply. Although usb0 described in DTS refers to the regulator by
vbus-supply, but there is no code related to regulator implemented
in the USB driver of QCA953X, so the USB of the device cannot work.
Under the regulator framework, adding the regulator-always-on attribute
fixes this problem, but it means that USB power will not be able to be
turned off. Since we need to control the USB power supply in user space,
I didn't find any other better way under the regulator framework of Linux,
so I directly export gpio.
Signed-off-by: Luo Chongjun <luochongjun@gl-inet.com>
(cherry picked from commit
b352124cd2115fec648a00956a848660df9477d3)
Hauke Mehrtens [Tue, 10 Jan 2023 18:50:12 +0000 (19:50 +0100)]
toolchain: musl: Fix symbol loading in gdb
Fix DT_DEBUG handling on MIPS in musl libc.
With this change gdb will load the symbol files for shared libraries on MIPS too.
This patch was taken from this thread: https://www.openwall.com/lists/musl/2022/01/09/4
Signed-off-by: Hauke Mehrtens <hmehrtens@maxlinear.com>
(cherry picked from commit
fcdd407e8e16b90e1995789ba217be5591a88d2f)
Yuu Toriyama [Tue, 14 Feb 2023 05:44:11 +0000 (14:44 +0900)]
wireless-regdb: update to 2023.02.13
Changes:
7f7a9f7 wireless-regdb: update regulatory database based on preceding changes
660a1ae wireless-regdb: Update regulatory info for Russia (RU) on 5GHz
fe05cc9 wireless-regdb: Update regulatory rules for Japan (JP) on 6GHz
d8584dc wireless-regdb: Update regulatory rules for Japan (JP) on 5GHz
c04fd9b wireless-regdb: update regulatory rules for Switzerland (CH)
f29772a wireless-regdb: Update regulatory rules for Brazil (BR)
Signed-off-by: Yuu Toriyama <PascalCoffeeLake@gmail.com>
(cherry picked from commit
1173edf23b3440137d60162d1ef9f48ffa13e3e2)
Prasun Maiti [Wed, 16 Nov 2022 11:03:33 +0000 (16:33 +0530)]
build: fix for sourcing targets image config installed via feeds
Sourcing of image/Config.in will not happen
When a target is installed from target/linux/feeds/
Signed-off-by: Prasun Maiti <prasunmaiti87@gmail.com>
Acked-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit
522a60cd31686a3d1b6d7ed1229eb68568aa89ac)
Sergio Paracuellos [Sat, 25 Feb 2023 11:01:40 +0000 (12:01 +0100)]
ramips: rt5350: enable lzma-loader for ALLNET ALL5003
Fixes the boot loader LZMA decompression issue:
LZMA ERROR 1 - must RESET board to recover
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
(cherry picked from commit
84c04ff4069a652755267d126418b211379c1cbf)
Chukun Pan [Sun, 12 Feb 2023 15:19:16 +0000 (23:19 +0800)]
bpf-headers: fix package category
This removes the non-selectable 'Kernel' item
when make menuconfig.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
(cherry picked from commit
3e4c014008659c760b2e4638f606da90df1e3c93)
Tomasz Maciej Nowak [Fri, 17 Feb 2023 13:21:01 +0000 (14:21 +0100)]
sdk: expose PATENTED an NLS build options
Some packages offer functionalities guarded by these options and it'll
be impossible to reach them without changing Config-build.in. So allow
to toggle these in more friendly way, by exposing them in configuration
menu.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
(cherry picked from commit
477ff0821a5e532adc0861d4093029967f5e1178)
Rosen Penev [Wed, 1 Feb 2023 22:50:22 +0000 (14:50 -0800)]
ksmbd: update to 3.4.7
Remove upstreamed patches.
Switch to normal tarballs. Codeload recently had a reproducibility issue.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
(cherry picked from commit
44c24b3ac5d4523c0f9f55691d28387508e93de5)
Felix Fietkau [Tue, 7 Mar 2023 09:23:17 +0000 (10:23 +0100)]
hostapd: add missing return code for the bss_mgmt_enable ubus method
Fixes bogus errors on ubus calls
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit
cf992ca862f271936f61367236378378f0d91b6d)
Robert Marko [Tue, 7 Mar 2023 14:00:28 +0000 (15:00 +0100)]
kernel: filter out pahole version
Pahole version is being autodetected during runtime since kernel 5.15.96
via in-kernel scripts/pahole-version.sh so add CONFIG_PAHOLE_VERSION to
kernel filter in order to prevent it from being added to target configs.
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit
5d8f14bfefc6f12e93425ee522bdce75a7c979d6)
Ruben Jenster [Thu, 23 Mar 2023 10:15:52 +0000 (11:15 +0100)]
dnsmasq: add dhcphostsfile to ujail sandbox
The dhcphostsfile must be mounted into the (ujail) sandbox.
The file can not be accessed without this mount.
Signed-off-by: Ruben Jenster <rjenster@gmail.com>
(cherry picked from commit
936df715de3d33947ce38ca232b05c2bd3ef58f1)
Andrey Erokhin [Tue, 7 Mar 2023 11:52:58 +0000 (16:52 +0500)]
netifd: strip mask from IP address in DHCP client params
ipaddr option can be in CIDR notation,
but udhcp wants just an IP address
Signed-off-by: Andrey Erokhin <a.erokhin@inango-systems.com>
(cherry picked from commit
506bb436c678779e8ee54e83a7fb3e4e880037ec)
Thomas Nixon [Sun, 26 Mar 2023 10:19:21 +0000 (10:19 +0000)]
lantiq: nand: don't yield while holding spinlock
The nand driver normally while waiting for the device to become ready;
this is normally fine, but xway_nand holds the ebu_lock spinlock, and
this can cause lockups if other threads which use ebu_lock are
interleaved. Fix this by waiting instead of polling.
This mainly showed up as crashes in ath9k_pci_owl_loader (see
https://github.com/openwrt/openwrt/issues/9829 ), but turning on
spinlock debugging shows this happening in other places too.
This doesn't seem to measurably impact boot time.
Tested on bt_homehub-v5a with 5.10 and 5.15.
Signed-off-by: Thomas Nixon <tom@tomn.co.uk>
[Add commit description into patch]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit
d3b47909b199b876f67a0387b5545cb73bd6b815)
Felix Fietkau [Fri, 24 Mar 2023 12:32:36 +0000 (13:32 +0100)]
mac80211: fix invalid calls to drv_sta_pre_rcu_remove
Potentially fixes some driver data structure corruption issues
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit
9779ee021d30508eb9e7ebf1ec0a28a4be3c4c19)
[Change patch number]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Felix Baumann [Fri, 31 Mar 2023 04:16:04 +0000 (06:16 +0200)]
ramips: mt7621: ASUS RT-AX53U add NMBM, nest firmware
Nests kernel and ubi into firmware partition in-order to be compatible
with OEM firmware. This allows restoring oem firmware from a backup of
firmware2. Add jffs2 partition which is present in the oem firmware.
Add support for mediatek NMBM (wear leveling on newer mediatek devices).
Exclude UBI partition from NMBM management.
Continues PR #10685.
Tested-by: Felix Baumann <felix.bau@gmx.de>
Signed-off-by: Felix Baumann <felix.bau@gmx.de>
(cherry picked from commit
787ecdf66de6798540fb8b756404566341b4733c)
Felix Baumann [Sun, 8 Jan 2023 00:47:21 +0000 (01:47 +0100)]
ramips: Alternative name Asus RT-AX1800U for Asus RT-AX53U
The Asus RT-AX1800U is identical to the already supported Asus RT-AX53U.
Use the ALT0 buildroot tags to show both devices.
Tested-by: Marian Sarcinschi <znevna@gmail.com>
Signed-off-by: Felix Baumann <felix.bau@gmx.de>
(cherry picked from commit
acd3b5e83b99879b326a940907a9ff334586f86b)
Marian Sarcinschi [Thu, 22 Dec 2022 23:56:09 +0000 (01:56 +0200)]
ramips: add missing LEDs to Asus RT-AX53U
This patch adds the missing LEDs to Asus RT-AX53U.
Based on PR #10400 and patch provided in #11068
- enable the two LEDs controlled by mt7915e for wireless;
- add label to power LED so it works properly and fix formatting;
- add the USB LED;
- switch LEDs are best left to be controlled by hardware for now.
Co-Authored-By: Ivan Rozhuk <rozhuk.im@gmail.com>
Co-Authored-By: Shiji Yang <yangshiji66@qq.com>
Co-Authored-By: Hartmut Birr <e9hack@gmail.com>
Tested-by: Felix Baumann <felix.bau@gmx.de>
Tested-by: Marian Sarcinschi <znevna@gmail.com>
Signed-off-by: Marian Sarcinschi <znevna@gmail.com>
(cherry picked from commit
c4b806d5c4ccc653968620e6e9aec93bc4e370e5)
Felix Baumann [Mon, 26 Dec 2022 20:44:45 +0000 (21:44 +0100)]
uboot-envtools: add support for ramips Asus RX-AX53U
Adds uboot-envtools support for ramips Asus RX-AX53U now that partition
can be correctly read.
Signed-off-by: Felix Baumann <felix.bau@gmx.de>
[ improve commit title and description ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit
75451681d03e609ac8a3d1cd7469eefa53e18ca4)
Felix Baumann [Mon, 26 Dec 2022 20:40:43 +0000 (21:40 +0100)]
ramips: add support for read/write uboot env to Asus RX-AX53U
Add support for read/writing uboot env by renaming the second partition
to its stock label "nvram" and remove the deemed unnecessary
"read-only". Split the first partition "u-boot" in two, in order
to allow `fw_setenv` safe write-access to the uboot environment
variables.
This implements hauke's request from [1].
Based on the patch provided by Shiji Yang.
[1] https://github.com/openwrt/openwrt/pull/10400#discussion_r945153224
Co-Authored-By: Shiji Yang <yangshiji66@qq.com>
Signed-off-by: Felix Baumann <felix.bau@gmx.de>
[ improve commit title and description, fix some whitespace problem ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit
3f1e9f6f3b14385cab7ca6d1dcc2a4b658475bc3)
Szabolcs Hubai [Fri, 24 Mar 2023 23:00:27 +0000 (00:00 +0100)]
comgt: ncm: support Mikrotik R11e-LTE6 modem
The Mikrotik R11e-LTE6 modem is similar to ZTE MF286R modem, added
earlier: it has a Marvel chip, able to work in ACM+RNDIS mode, knows ZTE
specific commands, runs OpenWrt Barrier Breaker fork.
While the modem is able to offer IPv6 address, the RNDIS setup is unable
to complete if there is an IPv6 adress.
While it works in ACM+RNDIS mode, the user experience isn't as good as
with "proto 3g": the modem happily serves a local IP (192.168.1.xxx)
without internet access. Of course, if the modem has enough time
(for example at the second dialup), it will serve a public IP.
Modifing the DHCP Lease (to a short interval before connect and back to
default while finalizing) is a workaround to get a public IP at the
first try.
A safe workaround for this is to excercise an offline script of the
pingcheck program: simply restart (ifdown - ifup) the connection.
Another pitfall is that the modem writes a few messages at startup,
which confuses the manufacturer detection algorithm and got disabled.
daemon.notice netifd: Interface 'mikrotik' is setting up now
daemon.notice netifd: mikrotik (2366): Failed to parse message data
daemon.notice netifd: mikrotik (2366): WARNING: Variable 'ok' does not exist or is not an array/object
daemon.notice netifd: mikrotik (2366): Unsupported modem
daemon.notice netifd: mikrotik (2426): Stopping network mikrotik
daemon.notice netifd: mikrotik (2426): Failed to parse message data
daemon.notice netifd: mikrotik (2426): WARNING: Variable '*simdetec:1,sim' does not exist or is not an array/object
daemon.notice netifd: mikrotik (2426): Unsupported modem
daemon.notice netifd: Interface 'mikrotik' is now down
A workaround for this is to use the "delay" option in the interface
configuration.
I want to thank Forum members dchard (in topic Adding support for
MikroTik hAP ac3 LTE6 kit (D53GR_5HacD2HnD)) [1]
and mrhaav (in topic OpenWrt X86_64 + Mikrotik R11e-LTE6) [2]
for sharing their experiments and works.
Another information page was found at eko.one.pl [3].
[1]: https://forum.openwrt.org/t/137555
[2]: https://forum.openwrt.org/t/151743
[3]: https://eko.one.pl/?p=modem-r11elte
Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
(cherry picked from commit
dbd6ebd6d84b35599a0446559576df41f487200e)
Szabolcs Hubai [Fri, 24 Mar 2023 21:24:26 +0000 (22:24 +0100)]
comgt: add quirk for Mikrotik modems based on Mikrotik R11e-LTE6
The MikroTik R11e-LTE6 modem goes into flight mode (CFUN=4) at startup
and the radio is off (*RADIOPOWER: 0):
AT+RESET
OK
OK
*SIMDETEC:2,NOS
*SIMDETEC:1,SIM
*ICCID:
8936500119010596302
*EUICC: 1
+MSTK: 11, D025....74F3
*ADMINDATA: 0, 2, 0
+CPIN: READY
*EUICC: 1
*ECCLIST: 5, 0, 112, 0, 000, 0, 08, 0, 118, 0, 911
+CREG: 0
$CREG: 0
+CESQ: 99,99,255,255,255,255
*CESQ: 99,99,255,255,255,255,0
+CGREG: 0
+CEREG: 0
+CESQ: 99,99,255,255,255,255
*CESQ: 99,99,255,255,255,255,0
*RADIOPOWER: 0
+MMSG: 0, 0
+MMSG: 0, 0
+MMSG: 1, 0
+MPBK: 1
While the chat script is able to establish the PPP connection,
it's closed instantly by the modem: LCP terminated by peer.
local2.info chat[7000]: send (ATD*99***1#^M)
local2.info chat[7000]: expect (CONNECT)
local2.info chat[7000]: ^M
local2.info chat[7000]: ATD*99***1#^M^M
local2.info chat[7000]: CONNECT
local2.info chat[7000]: -- got it
local2.info chat[7000]: send ( ^M)
daemon.info pppd[6997]: Serial connection established.
kern.info kernel: [ 453.659146] 3g-mikrotik: renamed from ppp0
daemon.info pppd[6997]: Renamed interface ppp0 to 3g-mikrotik
daemon.info pppd[6997]: Using interface 3g-mikrotik
daemon.notice pppd[6997]: Connect: 3g-mikrotik <--> /dev/ttyACM0
daemon.info pppd[6997]: LCP terminated by peer
daemon.notice pppd[6997]: Connection terminated.
daemon.notice pppd[6997]: Modem hangup
daemon.info pppd[6997]: Exit.
daemon.notice netifd: Interface 'mikrotik' is now down
Sending "AT+CFUN=1" to modem deactivates the flight mode and
solves the issue:
daemon.notice netifd: Interface 'mikrotik' is setting up now
daemon.notice netifd: mikrotik (7051): sending -> AT+CFUN=1
daemon.notice pppd[7137]: pppd 2.4.9 started by root, uid 0
local2.info chat[7140]: abort on (BUSY)
local2.info chat[7140]: abort on (NO CARRIER)
local2.info chat[7140]: abort on (ERROR)
local2.info chat[7140]: report (CONNECT)
local2.info chat[7140]: timeout set to 10 seconds
local2.info chat[7140]: send (AT&F^M)
local2.info chat[7140]: expect (OK)
local2.info chat[7140]: ^M
local2.info chat[7140]: +CESQ: 99,99,255,255,255,255^M
local2.info chat[7140]: ^M
local2.info chat[7140]: *CESQ: 99,99,255,255,255,255,0^M
local2.info chat[7140]: AT&F^MAT&F^M^M
local2.info chat[7140]: OK
local2.info chat[7140]: -- got it
...
local2.info chat[7140]: send (ATD*99***1#^M)
local2.info chat[7140]: expect (CONNECT)
local2.info chat[7140]: ^M
local2.info chat[7140]: ATD*99***1#^M^M
local2.info chat[7140]: CONNECT
local2.info chat[7140]: -- got it
local2.info chat[7140]: send ( ^M)
daemon.info pppd[7137]: Serial connection established.
kern.info kernel: [ 463.094254] 3g-mikrotik: renamed from ppp0
daemon.info pppd[7137]: Renamed interface ppp0 to 3g-mikrotik
daemon.info pppd[7137]: Using interface 3g-mikrotik
daemon.notice pppd[7137]: Connect: 3g-mikrotik <--> /dev/ttyACM0
daemon.warn pppd[7137]: Could not determine remote IP address: defaulting to 10.64.64.64
daemon.notice pppd[7137]: local IP address 100.112.63.62
daemon.notice pppd[7137]: remote IP address 10.64.64.64
daemon.notice pppd[7137]: primary DNS address 185.29.83.64
daemon.notice pppd[7137]: secondary DNS address 185.62.131.64
daemon.notice netifd: Network device '3g-mikrotik' link is up
daemon.notice netifd: Interface 'mikrotik' is now up
To send this AT command to the modem the "runcommand.gcom" script
dependency is moved from comgt-ncm to comgt.
As the comgt-ncm package depends on comgt already, this change
is a NOOP from that point of view.
But from the modem's point it is a low hanging fruit as the modem
is usable with installing comgt and kmod-usb-ncm packages.
Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
(cherry picked from commit
91eca7b04ff1309c7408baa1f1631d7623ce50cf)
Joe Mullally [Sun, 26 Feb 2023 22:01:22 +0000 (22:01 +0000)]
kernel: add support for XMC XM25QH64C
The XMC XM25QH64C is a 8MB SPI NOR chip. The patch is verified on TL-WPA8631P v3.
Datasheet available at https://www.xmcwh.com/uploads/442/XM25QH64C.pdf
Signed-off-by: Joe Mullally <jwmullally@gmail.com>
(cherry picked from commit
19752bdfa3e75da8290f525186e9fd8349df9c93)
Hauke Mehrtens [Sat, 1 Apr 2023 17:46:06 +0000 (19:46 +0200)]
ath79: Refresh patches
Refresh the kernel patches.
Fixes: c2331038b257 ("kernel: remove obsolete netfilter tcp window size check bypass patch")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Felix Fietkau [Thu, 30 Mar 2023 12:16:35 +0000 (14:16 +0200)]
kernel: remove obsolete netfilter tcp window size check bypass patch
On any currently supported hardware, the performance impact should not
matter anymore.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit
75e78bcaab847557ce1782eb2dea9dff9a029171)
Felix Fietkau [Wed, 29 Mar 2023 15:54:19 +0000 (17:54 +0200)]
mac80211, mt76: add fixes for recently discovered security issues
Fixes CVE-2022-47522
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit
d54c91bd9ab3c54ee06923eafbd67047816a37e4)
Mike Wilson [Mon, 20 Jul 2020 20:25:33 +0000 (22:25 +0200)]
ncm: add error check and retry mechanism for gcom call
This patch solves the problem of receiving "error" responses when
initially calling gcom. This avoids unnecessary NO_DEVICE failures.
A retry loop retries the call after an "error" response within the
specified delay. A successful response will continue with the connection
immediately without waiting for max specified delay, bringing the
interface up sooner.
Signed-off-by: Mike Wilson <mikewse@hotmail.com>
(cherry picked from commit
8f27093ce784daad5a9b1c89f51d0a76a8bbb07b)
John Audia [Wed, 22 Mar 2023 16:07:50 +0000 (12:07 -0400)]
kernel: bump 5.10 to 5.10.176
All patches automatically rebased.
Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit
f598880162e83ddc0139e00c5248497d06f5fff7)
John Audia [Sat, 18 Mar 2023 19:05:11 +0000 (15:05 -0400)]
kernel: bump 5.10 to 5.10.175
Manually rebased:
backport-5.10/611-v5.12-net-ethernet-mediatek-support-setting-MTU.patch
All other patches automatically rebased.
Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit
3ca98495897126113912f7ee4537f69459d21332)
John Audia [Mon, 13 Mar 2023 13:02:52 +0000 (09:02 -0400)]
kernel: bump 5.10 to 5.10.174
No patches needed to be rebased.
Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit
72d9d2b923b389f09e2ba43f4aba22c068e6cbb7)
John Audia [Sun, 12 Mar 2023 14:03:16 +0000 (10:03 -0400)]
kernel: bump 5.10 to 5.10.173
Manually rebased:
ramips/patches-5.10/810-uvc-add-iPassion-iP2970-support.patch
All other patches automatically rebased.
Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit
d4aad642ff80750ec16a58058eb6da718e2129cd)
John Audia [Sat, 11 Mar 2023 15:42:26 +0000 (10:42 -0500)]
kernel: tcindex classifier has been retired
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/net/sched?h=v5.10.173&id=
18c3fa7a7fdbb4d21dafc8a7710ae2c1680930f6
Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit
fbfec3286e8bfce3a78749b7bcb67e658665f197)
John Audia [Sat, 11 Mar 2023 19:03:00 +0000 (14:03 -0500)]
x86: fix deprecated CONFIG_MICROCODE_OLD_INTERACE
We use late loading[1] so need to set this option despite upstream adding a
kernel taint when this option is set. See discussion in PR#12149 for more details.
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/diff/arch/x86/Kconfig?id=v5.10.173&id2=v5.10.172
1. https://github.com/openwrt/openwrt/blob/master/target/linux/x86/base-files/lib/preinit/02_load_x86_ucode
Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit
0c5ffe1ab2b4843635555e2a234f8bd5cb4d6978)
John Audia [Fri, 3 Mar 2023 18:37:30 +0000 (13:37 -0500)]
kernel: bump 5.10 to 5.10.172
Removed upstreamed:
backport-5.10/804-0001-net-Remove-WARN_ON_ONCE-sk-sk_forward_alloc-from-sk_.patch[1]
All other patches automatically rebased.
1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.171&id=
3e4bbd1f38a8d35bd2d3aaffdb5f6ada546b669a
Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit
50cb897d251133752ea2cd338153a6dcb011ea98)
John Audia [Mon, 27 Feb 2023 22:58:42 +0000 (17:58 -0500)]
kernel: bump 5.10 to 5.10.170
No patches modified for this bump
Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit
a14cc979a2a081c31763b994219ae0d0ddebd9f2)
John Audia [Sat, 25 Feb 2023 21:20:28 +0000 (16:20 -0500)]
kernel: bump 5.10 to 5.10.169
Add fix:
target/linux/generic/backport-5.10/804-0001-net-Remove-WARN_ON_ONCE-sk-sk_forward_alloc-from-sk_.patch[3]
All other patches automatically rebased.
3. https://lore.kernel.org/stable/
20230227211548.13923-1-kuniyu@amazon.com
Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit
b88955aa2294c61f21bdf7014e10d8ea29d0c346)
Rafał Miłecki [Thu, 16 Mar 2023 21:01:51 +0000 (22:01 +0100)]
bcm4908: include usbport trigger
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit
cb2661844a5d54d44230ee564d4f17605a794a49)
Rafał Miłecki [Thu, 16 Mar 2023 19:28:47 +0000 (20:28 +0100)]
bcm4908: backport v6.4 pending DTS changes
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit
ffaabee9b8d9da7c15a50f52897ae5f70b40b4e7)
Daniel González Cabanelas [Thu, 16 Feb 2023 22:04:20 +0000 (23:04 +0100)]
ipq40xx: Linksys MR8300: fix the USB port power
The USB port on the MR8300 randomly fails to feed bus-powered devices.
This is caused by a misconfigured pinmux. The GPIO68 should be used to
enable the USB power (active low), but it's inside the NAND pinmux.
This GPIO pin was found in the original firmware at a startup script in
both MR8300 and EA8300. Therefore apply the fix for both boards.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit
ed64c3323590e3c9fa8b423bf37689023a7a101f)
Signed-off-by: Steffen Scheib <steffen@scheib.me>
Tony Butler [Sun, 19 Mar 2023 09:34:07 +0000 (02:34 -0700)]
ramips: mt7621: enable lzma-loader for AFOUNDRY EW1200
Fixes boot loader LZMA decompression issues (LZMA ERROR 1)
As reported in issue #12208
Reported-by: Raúl M. <raul.m@sparkedhost.com>
Tested-by: Raúl M. <raul.m@sparkedhost.com>
Signed-off-by: Tony Butler <spudz76@gmail.com>
(cherry picked from commit
889bbf89bb679f0c5b0fa432e27a3e0dd8940a4e)
Chuanhong Guo [Sun, 26 Mar 2023 15:50:43 +0000 (23:50 +0800)]
ramips: fix 5g mac for TOTOLINK X5000R
There's no valid mac address for the second band in the eeprom.
The vendor fw uses 2.4G mac + 4 as the mac for 5G radio.
Do the same in our firmware.
Fixes: 23be410b3d ("ramips: add support for TOTOLINK X5000R")
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
(cherry picked from commit
212632540043cc9b911c2efb86156479f2710836)
David Bauer [Thu, 23 Mar 2023 22:53:47 +0000 (23:53 +0100)]
ramips: add support for Mercusys MR70X
Hardware
========
- SoC: MediaTek MT7621AT (880MHz, Duel-Core)
- RAM: DDR3 128MB
- Flash: Winbond W25Q128JV (SPI-NOR 16MB)
- WiFi: MediaTek MT7915D (2.4GHz, 5GHz, DBDC)
- Ethernet: MediaTek MT7530 (WAN x1, LAN x3, SoC)
- UART: >TX RX GND 3v3 (115200 8N1, J1)
Do not connect 3v3. TX is marked with an arrow.
Installation
============
Flash factory image. This can be done using stock web ui.
Revert to stock firmware
========================
Flash stock firmware via OEM Web UI Recovery mode.
Web UI Recovery method
======================
1. Unplug the router
2. Plug in and hold reset button 5~10 secs
3. Set your computer IP address manually to 192.168.1.x / 255.255.255.0
4. Flash image with web browser to 192.168.1.1
Co-authored-by: Robert Senderek <robert.senderek@10g.pl>
Co-authored-by: Yoonji Park <koreapyj@dcmys.kr>
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit
47de2c686291e69afc9f443e27e1dfd11ed5fbe7)
David Bauer [Fri, 24 Mar 2023 14:35:47 +0000 (15:35 +0100)]
firmware-utils: tplink-safeloader: add Mercusys MR70X
Signed-off-by: David Bauer <mail@david-bauer.net>
David Bauer [Tue, 21 Mar 2023 04:07:30 +0000 (05:07 +0100)]
ramips: fix Archer AX23 WiFi MAC address conflict
The original claim about conflicting MAC addresses is wrong. mac80211
does increment the first octet and sets the LA bit.
This means our "workaround" actually leads to the issue while
incrementing the last octet is safe.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit
d52870125d57d39e73e6c305dd36fad44fe4a773)
David Bauer [Tue, 14 Mar 2023 01:06:40 +0000 (02:06 +0100)]
ramips: add support for TP-Link Archer AX23 v1
Hardware
--------
CPU: MediaTek MT7621 DAT
RAM: 128MB DDR3 (integrated)
FLASH: 16MB SPI-NOR ()
WiFi: MediaTek MT7905 + MT7975 (2.4 / 5 DBDC) 802.11ax
SERIAL: 115200 8N1
LEDs - (3V3 - GND - RX - TX) - ETH ports
Installation
------------
Upload the factory image using the Web-UI.
Web-Recovery
------------
The router supports a HTTP recovery mode by holding the reset-button
when powering on. The interface is reachable at 192.168.0.1 and supports
installation using the factory image.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit
7dceef5ee554ec4ab5d2dd2ff999f4a60bf2e0f4)
David Bauer [Wed, 15 Mar 2023 00:22:16 +0000 (01:22 +0100)]
firmware-utils: tplink-safeloader: add TP-Link Archer AX23 v1
Signed-off-by: David Bauer <mail@david-bauer.net>
David Bauer [Sat, 18 Feb 2023 01:06:54 +0000 (02:06 +0100)]
mpc85xx: add support for Watchguard Firebox T10
Hardware
--------
SoC: Freescale P1010
RAM: 512MB
FLASH: 1 MB SPI-NOR
512 MB NAND
ETH: 3x Gigabite Ethernet (Atheros AR8033)
SERIAL: Cisco RJ-45 (115200 8N1)
RTC: Battery-Backed RTC (I2C)
Installation
------------
1. Patch U-Boot by dumping the content of the SPI-Flash using a SPI
programmer. The SHA1 hash for the U-Boot password is currently
unknown.
A tool for patching U-Boot is available at
https://github.com/blocktrron/t10-uboot-patcher/
You can also patch the unknown password yourself. The SHA1 hash is
E597301A1D89FF3F6D318DBF4DBA0A5ABC5ECBEA
2. Interrupt the bootmenu by pressing CTRL+C. A password prompt appears.
The patched password is '1234' (without quotation marks)
3. Download the OpenWrt initramfs image. Copy it to a TFTP server
reachable at 10.0.1.13/24 and rename it to uImage.
4. Connect the TFTP server to ethernet port 0 of the Watchguard T10.
5. Download and boot the initramfs image by entering "tftpboot; bootm;"
in U-Boot.
6. After OpenWrt booted, create a UBI volume on the old data partition.
The "ubi" mtd partition should be mtd7, check this using
$ cat /proc/mtd
Create a UBI partition by executing
$ ubiformat /dev/mtd7 -y
7. Increase the loadable kernel-size of U-Boot by executing
$ fw_setenv SysAKernSize 800000
8. Transfer the OpenWrt sysupgrade image to the Watchguard T10 using
scp. Install the image by using sysupgrade:
$ sysupgrade -n <path-to-sysupgrade>
Note: The LAN ports of the T10 are 1 & 2 while 0 is WAN. You might
have to change the ethernet-port.
9. OpenWrt should now boot from the internal NAND. Enjoy.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit
35f6d795134e9b089c4e763a7f58cba7d4e15e42)
David Bauer [Sun, 5 Mar 2023 19:26:21 +0000 (20:26 +0100)]
generic: remove patch for unused kernel version
Remove this stray patch, as OpenWrt 22.03 does not target kernel 5.15.
Fixes commit
b18a0d0b92963 ("generic: add support for EON EN25QX128A spi nor flash")
Signed-off-by: David Bauer <mail@david-bauer.net>
David Bauer [Thu, 2 Mar 2023 15:53:59 +0000 (16:53 +0100)]
generic: MIPS: Add barriers between dcache & icache flushes
This fixes spurious boot-errors with some ath79 MIPS 74Kc boards such
as the AC Lite as well as Archer C7 v2.
The missing barrier leads to the icache flush being executed before the
dcache writeback, which results in the CPU executing the dummy infinite
loop in tlbmiss_handler_setup_pgd.
Applying this patch from upstream ensures the dcache is written back
before flushing the icache.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit
26bc8f68767e1ec6e33a84ef397e4c38d5968462)
Felix Fietkau [Thu, 2 Mar 2023 11:58:16 +0000 (12:58 +0100)]
kernel: fix mtk dsa tag padding
The padding intended to avoid corrupted non-zero padding payload was
accidentally adding too many padding bytes, tripping up some setups.
Fix this by using eth_skb_pad instead.
Fixes #11942.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit
9307c27539805de021fb7163f6ad6dc08992331b)
Tim Harvey [Sat, 18 Feb 2023 00:53:18 +0000 (16:53 -0800)]
kernel: can: fix MCP251x CAN controller module autoload
Fix autoload module name for can-mcp251x kmod.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
(cherry picked from commit
29d02d8ce584fa7e420204e04dde1e17e14e009c)
John Audia [Wed, 15 Feb 2023 19:05:27 +0000 (14:05 -0500)]
kernel: bump 5.10 to 5.10.168
Manually rebased:
backport-5.10/804-v5.14-0001-nvmem-core-allow-specifying-of_node.patch
Removed upstreamed:
generic-backport/807-v5.17-0003-nvmem-core-Fix-a-conflict-between-MTD-and-NVMEM-on-w.patch[1]
All other patches automatically rebased.
1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.168&id=
34ec4c7831c416ac56619477f1701986634a7efc
Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3
Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit
461072fc7b3d8fa77347a884fe5d36c81f660da8)
[Refresh on OpenWrt 22.03]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
John Audia [Mon, 6 Feb 2023 11:28:36 +0000 (06:28 -0500)]
kernel: bump 5.10 to 5.10.167
All patches automatically rebased.
Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3
Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit
712681458a65736d3fc625bb9c481c31b23c1f97)
John Audia [Tue, 7 Feb 2023 19:56:52 +0000 (14:56 -0500)]
openssl: bump to 1.1.1t
Changes between 1.1.1s and 1.1.1t [7 Feb 2023]
*) Fixed X.400 address type confusion in X.509 GeneralName.
There is a type confusion vulnerability relating to X.400 address processing
inside an X.509 GeneralName. X.400 addresses were parsed as an ASN1_STRING
but subsequently interpreted by GENERAL_NAME_cmp as an ASN1_TYPE. This
vulnerability may allow an attacker who can provide a certificate chain and
CRL (neither of which need have a valid signature) to pass arbitrary
pointers to a memcmp call, creating a possible read primitive, subject to
some constraints. Refer to the advisory for more information. Thanks to
David Benjamin for discovering this issue. (CVE-2023-0286)
This issue has been fixed by changing the public header file definition of
GENERAL_NAME so that x400Address reflects the implementation. It was not
possible for any existing application to successfully use the existing
definition; however, if any application references the x400Address field
(e.g. in dead code), note that the type of this field has changed. There is
no ABI change.
[Hugo Landau]
*) Fixed Use-after-free following BIO_new_NDEF.
The public API function BIO_new_NDEF is a helper function used for
streaming ASN.1 data via a BIO. It is primarily used internally to OpenSSL
to support the SMIME, CMS and PKCS7 streaming capabilities, but may also
be called directly by end user applications.
The function receives a BIO from the caller, prepends a new BIO_f_asn1
filter BIO onto the front of it to form a BIO chain, and then returns
the new head of the BIO chain to the caller. Under certain conditions,
for example if a CMS recipient public key is invalid, the new filter BIO
is freed and the function returns a NULL result indicating a failure.
However, in this case, the BIO chain is not properly cleaned up and the
BIO passed by the caller still retains internal pointers to the previously
freed filter BIO. If the caller then goes on to call BIO_pop() on the BIO
then a use-after-free will occur. This will most likely result in a crash.
(CVE-2023-0215)
[Viktor Dukhovni, Matt Caswell]
*) Fixed Double free after calling PEM_read_bio_ex.
The function PEM_read_bio_ex() reads a PEM file from a BIO and parses and
decodes the "name" (e.g. "CERTIFICATE"), any header data and the payload
data. If the function succeeds then the "name_out", "header" and "data"
arguments are populated with pointers to buffers containing the relevant
decoded data. The caller is responsible for freeing those buffers. It is
possible to construct a PEM file that results in 0 bytes of payload data.
In this case PEM_read_bio_ex() will return a failure code but will populate
the header argument with a pointer to a buffer that has already been freed.
If the caller also frees this buffer then a double free will occur. This
will most likely lead to a crash.
The functions PEM_read_bio() and PEM_read() are simple wrappers around
PEM_read_bio_ex() and therefore these functions are also directly affected.
These functions are also called indirectly by a number of other OpenSSL
functions including PEM_X509_INFO_read_bio_ex() and
SSL_CTX_use_serverinfo_file() which are also vulnerable. Some OpenSSL
internal uses of these functions are not vulnerable because the caller does
not free the header argument if PEM_read_bio_ex() returns a failure code.
(CVE-2022-4450)
[Kurt Roeckx, Matt Caswell]
*) Fixed Timing Oracle in RSA Decryption.
A timing based side channel exists in the OpenSSL RSA Decryption
implementation which could be sufficient to recover a plaintext across
a network in a Bleichenbacher style attack. To achieve a successful
decryption an attacker would have to be able to send a very large number
of trial messages for decryption. The vulnerability affects all RSA padding
modes: PKCS#1 v1.5, RSA-OEAP and RSASVE.
(CVE-2022-4304)
[Dmitry Belyavsky, Hubert Kario]
Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit
4ae86b3358a149a17411657b12103ccebfbdb11b)
The original commit removed the upstreamed patch 010-padlock.patch, but
it's not on OpenWrt 22.03, so it doesn't have to be removed.
Signed-off-by: Michal Vasilek <michal.vasilek@nic.cz>
Christian Marangi [Wed, 18 Jan 2023 11:22:12 +0000 (12:22 +0100)]
bpf: ignore missing LLVM bins on package for non compile steps
To download a package the LLVM bins are not strictly needed.
Currently with an example run of make package/bridger/download V=s, the
build fail with
make[2]: Entering directory '/home/ansuel/openwrt-ansuel/openwrt/package/network/services/bridger'
bash: line 1: /home/ansuel/openwrt-ansuel/openwrt/staging_dir/host/llvm-bpf/bin/clang: No such file or directory
bash: line 1: [: : integer expression expected
/home/ansuel/openwrt-ansuel/openwrt/include/bpf.mk:71: *** ERROR: LLVM/clang version too old. Minimum required: 12, found: . Stop.
make[2]: Leaving directory '/home/ansuel/openwrt-ansuel/openwrt/package/network/services/bridger'
time: package/network/services/bridger/download#0.04#0.00#0.06
ERROR: package/network/services/bridger failed to build.
This is wrong since it may be needed to download the required packages
first and then compile them later.
Fix this by ignoring the LLVM bin check on non compile steps.
Tested-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit
116c73fd71c75e38c4d707dc5a74e6993874098f)
Hauke Mehrtens [Wed, 26 Oct 2022 21:05:31 +0000 (23:05 +0200)]
bpf: check llvm version only when used
unetd always includes $(INCLUDE_DIR)/bpf.mk. This file always checks if
the LLVM version is supported in CLANG_VER_VALID. unetd only needs bpf
when UNETD_VXLAN_SUPPORT is set. It fails when UNETD_VXLAN_SUPPORT is
not set and llvm is not installed.
Fix it by only checking the LLVM version when a LLVM toolchain is
available.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit
c58177b5dcb3461efef0adefe570dd8a8d966ec4)
Petr Štetiar [Tue, 3 Jan 2023 11:44:51 +0000 (12:44 +0100)]
at91: sam9x,sama5: fix racy SD card image generation
We've few low spec (make -j3) build workers attached to the 22.03
buildbot instance which from time to time exhibit following build
failure during image generation (shortened for brewity):
+ dd bs=512 if=root.ext4 of=openwrt-22.03...sdcard.img.gz.img
dd: failed to open 'root.ext4': No such file or directory
Thats happening likely due to the fact, that on buildbots we've
`TARGET_PER_DEVICE_ROOTFS=y` which produces differently named filesystem
image in the SD card image target dependency chain:
make_ext4fs -L rootfs ... root.ext4+pkg=
68b329da
and that hardcoded `root.ext4` image filename becomes available from
other Make targets in the later stages. So lets fix this issue by using
IMAGE_ROOTFS Make variable which should contain proper path to the root
filesystem image.
Fixing remaining subtargets ommited in commit
5c3679e39b61 ("at91:
sama7: fix racy SD card image generation").
Fixes: 5c3679e39b61 ("at91: sama7: fix racy SD card image generation")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit
3b669bc3f32f7594f38187a284a65ca2c35a0121)
Petr Štetiar [Tue, 3 Jan 2023 11:44:51 +0000 (12:44 +0100)]
at91: sama7: fix racy SD card image generation
We've few low spec (make -j3) build workers attached to the 22.03
buildbot instance which from time to time exhibit following build
failure during image generation:
+ dd bs=512 if=root.ext4 of=openwrt-22.03-snapshot-r20028-
43d71ad93e-at91-sama7-microchip_sama7g5-ek-ext4-sdcard.img.gz.img seek=135168 conv=notrunc
dd: failed to open 'root.ext4': No such file or directory
Thats likely due to the fact, that on buildbots we've
`TARGET_PER_DEVICE_ROOTFS=y` which produces differently named filesystem
image in the SD card image target dependency chain:
make_ext4fs -L rootfs ... root.ext4+pkg=
68b329da
and that hardcoded root.ext4 becomes available from other target in the
later stages. So lets fix this issue by using IMAGE_ROOTFS Make variable
which should contain proper path to the root filesystem image.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit
5c3679e39b615ff29c9315f810e8e15775cc2d01)
Hauke Mehrtens [Sun, 29 Jan 2023 17:55:38 +0000 (18:55 +0100)]
mac80211: Update to version 5.15.92-1
This update mac80211 to version 5.15.92-1. This includes multiple
bugfixes. Some of these bugfixes are fixing security relevant bugs.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
John Audia [Wed, 1 Feb 2023 20:44:56 +0000 (15:44 -0500)]
kernel: bump 5.10 to 5.10.166
All patches automatically rebased.
Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3
Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit
50324b949b91cfb70ced3869b09b895e45a5ae37)
Arınç ÜNAL [Mon, 28 Nov 2022 21:33:37 +0000 (00:33 +0300)]
ramips: mt7621-dts: fix phy-mode of external phy on GB-PC2
The phy-mode property must be defined on the MAC instead of the PHY. Define
phy-mode under gmac1 which the external phy is connected to.
Tested-by: Petr Louda <petr.louda@outlook.cz>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
(cherry picked from commit
5155200f97adaeaaac7b752b5a6a5e41cba3db6a)
Tim Harvey [Wed, 28 Dec 2022 21:38:15 +0000 (13:38 -0800)]
octeontx: add sqaushfs and ramdisk to features
Add squashfs and ramdisk to features as these are commonly used images
for the octeontx.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
(cherry picked from commit
af5635e6ca12d3be275560a58ac6e2793e218fcd)
Tom Herbers [Sat, 10 Sep 2022 14:45:42 +0000 (16:45 +0200)]
ath79: add LTE packages for GL-XE300
Add LTE packages required for operating the LTE modems shipped with
the GL-XE300.
Example configuration for an unauthenticated dual-stack APN:
network.wwan0=interface
network.wwan0.proto='qmi'
network.wwan0.device='/dev/cdc-wdm0'
network.wwan0.apn='internet'
network.wwan0.auth='none'
network.wwan0.delay='10'
network.wwan0.pdptype='IPV4V6'
Signed-off-by: Tom Herbers <mail@tomherbers.de>
(cherry picked from commit
67f283be4430ebfb46be6c00fcc7c12a6adabce3)
Tom Herbers [Tue, 24 Jan 2023 13:14:58 +0000 (14:14 +0100)]
ath79: add label-mac-device for GL-XE300
This adds an label-mac-device alias which refrences the mac which is
printed on the Label of the device.
Signed-off-by: Tom Herbers <mail@tomherbers.de>
(cherry picked from commit
f83f5f8452edd3115aacf333b0038da89639a218)
Leo Soares [Sun, 31 Jul 2022 14:28:47 +0000 (15:28 +0100)]
ath79: add LTE led for GL.iNet GL-XE300
This commit adds the LTE led for GL.iNet GL-XE300
to the default leds config.
Signed-off-by: Leo Soares <leo@hyper.ag>
(cherry picked from commit
35a0f2b00c44a43ad087327f0cbdb1c9c5e60c49)
Signed-off-by: Tom Herbers <mail@tomherbers.de>
Etienne Champetier [Mon, 30 Jan 2023 21:43:00 +0000 (23:43 +0200)]
kernel: backport some mv88e6xxx devlink patches
This should help debug mv88e6xxx issues
Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
John Audia [Tue, 24 Jan 2023 12:36:07 +0000 (07:36 -0500)]
kernel: bump 5.10 to 5.10.165
All patches automatically rebased.
Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3
Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit
257e9fc57cf2c0391f8d99c25e82d75b73695c8a)
John Audia [Wed, 18 Jan 2023 19:45:07 +0000 (14:45 -0500)]
kernel: bump 5.10 to 5.10.164
All patches automatically rebased
Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3
Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit
9c3954bc46fce58a0f2dbe8bf6d3f507cfcd1dfb)
John Audia [Sat, 14 Jan 2023 11:31:07 +0000 (06:31 -0500)]
kernel: bump 5.10 to 5.10.163
Removed upstreamed:
generic/101-Use-stddefs.h-instead-of-compiler.h.patch[1]
bcm27xx/patches-5.10/950-0194-drm-fourcc-Add-packed-10bit-YUV-4-2-0-format.patch
All patches automatically rebased.
1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.163&id=
ddd2bb08bd99b7ee4442fbbe0f9b80236fdd71d2
Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3
Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit
2835df54ab84a8709057df156932497b19cda449)
John Audia [Thu, 5 Jan 2023 10:51:15 +0000 (05:51 -0500)]
kernel: bump 5.10 to 5.10.162
All patches automatically rebased.
Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3
Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit
2621ddb0bef7f5f8eedc49437dfa23b66e810af6)
David Bauer [Sat, 28 Jan 2023 12:50:17 +0000 (13:50 +0100)]
mac80211: use 802.11ax iw modes
This adds missing HE modes to mac80211_prepare_ht_modes.
Previously mesh without wpa_supplicant would be initialized with 802.11g
/NO-HT only, as this method did not parse channel bandwidth for HE
operation.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit
a63430eac33ceb1dbf96d3667e2a0f2e04ba391f)
Chuanhong Guo [Sat, 21 Jan 2023 02:47:59 +0000 (10:47 +0800)]
kernel: mtk-bmt: fix usage of _oob_read
_oob_read returns number of bitflips on success while
bbt_nand_read should return 0.
Fixes: 2d49e49b18 ("mediatek: bmt: use generic mtd api")
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
(cherry picked from commit
f183ce35b8ea2fd991ac489fb223b09a1ecb4db0)
Christian Marangi [Sun, 22 Jan 2023 00:35:16 +0000 (01:35 +0100)]
tools/mkimage: build uboot with NO_SDL=1
From uboot Documentation for uboot-2022.01 for tools-only we can build
with NO_SDL=1 to skip installing the sdl2 package.
Follow this to fix compilation error on macos
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Florian Maurer [Sun, 15 Jan 2023 20:22:22 +0000 (20:22 +0000)]
lantiq: xrx200: Fix wifi LED on o2 box 6431
Wifi LED did not work using phy0radio, which somehow slipped through in
the previous testing
Signed-off-by: Florian Maurer <f.maurer@outlook.de>
(cherry picked from commit
2e3d1edf59109d6329a00d90b1e953261d602af5)
David Bauer [Wed, 18 Jan 2023 21:06:36 +0000 (22:06 +0100)]
mbedtls: move source modification to patch
Patch the mbedtls source instead of modifying the compile-targets
in the prepare buildstep within OpenWrt.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit
00f1463df7e690862403208082f71fb4741baf02)