John Crispin [Fri, 24 Jul 2015 09:09:22 +0000 (09:09 +0000)]
ramips: add support for STORYLiNK SAP-G3200U3
STORYLiNK SAP-G3200U3 is an AC1200 router based on MT7621AT+MT7602EN+MT7612EN.
It has 128MB DDR3, 8MB NOR FLASH, 5-port Gbps switch and 1x USB 3.0.
The following patch adds support for this device.
Tested and working:
* ethernet
* both WiFi radios
* USB 3.0
* buttons
* ethernet switch and USB diag LEDs
* UART
* GPIOs
Tested and not working:
* LEDs for WiFi radios (connected with WiFi chips, not supported in mt76?)
* failsafe mode (known problem, needs workaround like other MTK based devices)
More information in Wiki: http://wiki.openwrt.org/toh/storylink/sap-g3200u3
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46454
John Crispin [Fri, 24 Jul 2015 09:09:07 +0000 (09:09 +0000)]
lantiq: Silence the PCIe error interrupt printk also in 4.1
This ports
9e2a7b779e6f0914395da3657b00f0ac00209bfd to the 4.1 patches.
I forgot this when preparing the initial 4.1 patch.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 46453
John Crispin [Fri, 24 Jul 2015 09:09:02 +0000 (09:09 +0000)]
lantiq: Fix ifxos driver on linux 4.1
request_mem_region returns NULL when requesting the region failed, and
a valid pointer when it was successful. Currently the condition is
inverted.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 46452
John Crispin [Fri, 24 Jul 2015 09:08:57 +0000 (09:08 +0000)]
kmod-regmap: enable MMIO support
This adds MMIO support for kmod-regmap.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 46451
Jonas Gorski [Wed, 22 Jul 2015 12:51:11 +0000 (12:51 +0000)]
kernel: refresh patches for 4.1
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46441
Jonas Gorski [Wed, 22 Jul 2015 12:51:04 +0000 (12:51 +0000)]
kernel: update 4.0 to 4.0.9
Changelog:
* https://www.kernel.org/pub/linux/kernel/v4.x/ChangeLog-4.0.9
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46440
Jonas Gorski [Wed, 22 Jul 2015 12:50:59 +0000 (12:50 +0000)]
kernel: update 3.18 to 3.18.19
Changelog:
* https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.18.19
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46439
Felix Fietkau [Wed, 22 Jul 2015 12:45:12 +0000 (12:45 +0000)]
ar71xx: refresh kernel config
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46438
Felix Fietkau [Wed, 22 Jul 2015 12:45:07 +0000 (12:45 +0000)]
kernel: update to linux 4.1.3
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46437
Felix Fietkau [Wed, 22 Jul 2015 12:45:03 +0000 (12:45 +0000)]
mac80211: update to wireless-testing 2015-07-21
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46436
Felix Fietkau [Wed, 22 Jul 2015 12:44:55 +0000 (12:44 +0000)]
generic: add more missing linux 4.1 symbols
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 46435
Felix Fietkau [Mon, 20 Jul 2015 10:50:46 +0000 (10:50 +0000)]
tools: drop circular dependency between patch and ccache, build patch without ccache (fixes #20132)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46434
Felix Fietkau [Mon, 20 Jul 2015 06:01:18 +0000 (06:01 +0000)]
ar71xx: remove the use of the obsolete IRQF_DISABLED flag in the NAND flash driver (fixes #20125)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46433
Felix Fietkau [Sun, 19 Jul 2015 17:59:20 +0000 (17:59 +0000)]
ar71xx: switch to linux 4.1
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46432
Felix Fietkau [Sun, 19 Jul 2015 17:59:15 +0000 (17:59 +0000)]
ar71xx: add missing patch chunk to 4.1 unaligned access hacks
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46431
Felix Fietkau [Sun, 19 Jul 2015 17:59:08 +0000 (17:59 +0000)]
ar71xx: reorganize 4.1 patch directory layout
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46430
Felix Fietkau [Sun, 19 Jul 2015 17:59:00 +0000 (17:59 +0000)]
ar71xx: refresh kernel config
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46429
Felix Fietkau [Sun, 19 Jul 2015 17:58:53 +0000 (17:58 +0000)]
kernel: add missing config symbols for 4.1
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46428
Felix Fietkau [Sun, 19 Jul 2015 17:58:46 +0000 (17:58 +0000)]
ar71xx: refresh 4.1 patches
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46427
Felix Fietkau [Sun, 19 Jul 2015 17:58:40 +0000 (17:58 +0000)]
ar71xx: add 4.1 support
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 46426
Felix Fietkau [Sun, 19 Jul 2015 17:58:27 +0000 (17:58 +0000)]
Revert "ar71xx: Add support for Cisco-Linksys WAP4410N" (r46250)
The commit is incomplete, it does not even build the mach-* file
This reverts commit
6e6adcf7a197b1802cb728ddcccf05f890ca0574
SVN-Revision: 46425
Felix Fietkau [Sun, 19 Jul 2015 14:59:26 +0000 (14:59 +0000)]
mkimage: cross compile fix: pass HOST_*FLAGS in to uboot's makefile
The HOST_*FLAGS are for compiling programs which will run on the machine that is
running the build. Setting these flags is frequently required for unusual
cross-compiles.
Signed-off-by: Lawrence D'Anna <larry@elder-gods.org>
SVN-Revision: 46424
Felix Fietkau [Sun, 19 Jul 2015 14:59:16 +0000 (14:59 +0000)]
strace: add kernel headers include to host cflags to fix build on non-linux systems
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46423
Felix Fietkau [Sun, 19 Jul 2015 14:59:09 +0000 (14:59 +0000)]
strace: cross compile fix: pass HOST_*FLAGS in to ./configure
The HOST_*FLAGS are for compiling programs which will run on the machine that is
running the build. Setting these flags is frequently required for unusual
cross-compiles.
Signed-off-by: Lawrence D'Anna <larry@elder-gods.org>
SVN-Revision: 46422
Felix Fietkau [Sat, 18 Jul 2015 23:14:19 +0000 (23:14 +0000)]
netifd: update to the latest version, fixes setting RPS/XPS for wlan devices
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46421
Felix Fietkau [Sat, 18 Jul 2015 22:49:39 +0000 (22:49 +0000)]
kernel: fix sched_getaffinity on MIPS SMP systems (fixes enabling RPS/XPS in netifd with musl)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46420
John Crispin [Sat, 18 Jul 2015 21:15:42 +0000 (21:15 +0000)]
ar71xx: Enable ath10k calibration data loading for EnGenius ESR1750 and EPG500.
As r46245 disabled the board.bin template workaround, 5GHz wifi stopped working
on these devices. This adds them to the calibration data loading introduced in
r46244 and thus makes 5GHz work again for these devices.
Signed-off-by: Christian Beier <cb@shoutrlabs.com>
SVN-Revision: 46415
John Crispin [Sat, 18 Jul 2015 21:15:36 +0000 (21:15 +0000)]
ar71xx: use automatic firmware partition splitting for devolo dLAN devices
Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de>
SVN-Revision: 46414
Felix Fietkau [Sat, 18 Jul 2015 19:10:38 +0000 (19:10 +0000)]
cfg80211: fix a locking issue (#20098)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46413
Felix Fietkau [Sat, 18 Jul 2015 16:47:05 +0000 (16:47 +0000)]
ramips: enable mt76 by default for mt7621
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46410
Felix Fietkau [Sat, 18 Jul 2015 16:04:58 +0000 (16:04 +0000)]
mt76: update to the latest version, fixes rx buffer allocation issues
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46409
Steven Barth [Sat, 18 Jul 2015 05:44:50 +0000 (05:44 +0000)]
odhcp6c: add option "sourcefilter" to disable source filter
Signed-off-by: Steven Barth <steven@midlink.org>
SVN-Revision: 46408
Hauke Mehrtens [Fri, 17 Jul 2015 17:55:17 +0000 (17:55 +0000)]
kernel: fix dependecy of kmod-ieee802154_6lowpan
This module also depends on kmod-ieee802154
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46407
John Crispin [Fri, 17 Jul 2015 12:51:24 +0000 (12:51 +0000)]
swconfig: libsw.so should be installed into /usr/lib/
otherwise it's not picked up by toolchain:
staging_dir/toolchain-mipsel_24kec+dsp_gcc-4.8-linaro_musl-1.1.10/lib/gcc/mipsel-openwrt-linux-musl/4.8.3/../../../../mipsel-openwrt-linux-musl/bin/ld: cannot find -lsw
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 46406
John Crispin [Fri, 17 Jul 2015 12:51:08 +0000 (12:51 +0000)]
ramips: add support for Planex MZK-DP150N
This patch add support for Planex MZK-DP150N.
a mini router on the MT7620A SoC with one Ethernet port and a 802.11n 2.4 GHz radio.
Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
SVN-Revision: 46405
John Crispin [Fri, 17 Jul 2015 12:50:52 +0000 (12:50 +0000)]
brcm2708: add gzip image compression
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 46404
John Crispin [Fri, 17 Jul 2015 12:49:27 +0000 (12:49 +0000)]
brcm2708: add Raspberry Pi Compute Module support
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 46403
John Crispin [Fri, 17 Jul 2015 12:49:09 +0000 (12:49 +0000)]
brcm2708: switch to linux 4.1
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 46402
John Crispin [Fri, 17 Jul 2015 12:48:59 +0000 (12:48 +0000)]
brcm2708: add upstream (bcm2835) modules and improve downstream ones (bcm2708)
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 46401
John Crispin [Fri, 17 Jul 2015 12:48:51 +0000 (12:48 +0000)]
generic: add missing linux 4.1 symbols
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 46400
John Crispin [Fri, 17 Jul 2015 12:48:39 +0000 (12:48 +0000)]
brcm2708: add linux 4.1 support
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 46399
John Crispin [Fri, 17 Jul 2015 12:48:11 +0000 (12:48 +0000)]
brcm2708: split target config into subtargets
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 46398
John Crispin [Fri, 17 Jul 2015 12:48:02 +0000 (12:48 +0000)]
brcm2708: remove unneeded base-files
Device tree exports board name/model and device LEDs.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 46397
John Crispin [Fri, 17 Jul 2015 12:47:50 +0000 (12:47 +0000)]
brcm2708: improve profiles and image generation
- Add profiles for bcm2708 subtarget.
- Check subtarget for image generation.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 46396
Jo-Philipp Wich [Fri, 17 Jul 2015 11:37:20 +0000 (11:37 +0000)]
toplevel.mk: fix LD_LIBRARY_PATH for host binaries
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 46394
Steven Barth [Fri, 17 Jul 2015 11:09:13 +0000 (11:09 +0000)]
odhcpd: fix last commit
Signed-off-by: Steven Barth <steven@midlink.org>
SVN-Revision: 46393
Steven Barth [Fri, 17 Jul 2015 08:47:48 +0000 (08:47 +0000)]
odhcpd: fix dhcpv6 relay forwarding
Signed-off-by: Steven Barth <steven@midlink.org>
SVN-Revision: 46392
Jonas Gorski [Thu, 16 Jul 2015 11:15:02 +0000 (11:15 +0000)]
brcm63xx: make use of dt-includes
Now that we have a dtc command that invokes the preprocessor, make use
of it and replace the magic numbers with KEY_* defines.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46391
Jonas Gorski [Thu, 16 Jul 2015 11:13:47 +0000 (11:13 +0000)]
brcm63xx: make use of the new BuildDTB command
Now that we have a BuildDTB command, make use of it instead of calling
dtc directly.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46390
Jonas Gorski [Thu, 16 Jul 2015 11:12:52 +0000 (11:12 +0000)]
image.mk: add a BuildDTB define
Add a Image/BuildDTB command that takes the path to an dts file and
applies the CPP using the default include directories, then uses dtc
to compile the dts as the specified output file.
Additional CPP and DTC flags can be supplied as additional arguments.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46389
Jonas Gorski [Thu, 16 Jul 2015 11:12:41 +0000 (11:12 +0000)]
brcm63xx: HG553 buttons support
This patch adds buttons support for Huawei EchoLife HG553.
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46388
Jonas Gorski [Thu, 16 Jul 2015 11:12:03 +0000 (11:12 +0000)]
kernel: wpan: at86rf230 depends on regmap-spi
kmod-at86rf230 select REGMAP_SPI since 3.17, so add a dependency to
kmod-regmap.
Fixes the following error:
Package kmod-at86rf230 is missing dependencies for the following libraries:
regmap-core.ko
regmap-spi.ko
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46387
Jonas Gorski [Wed, 15 Jul 2015 14:42:04 +0000 (14:42 +0000)]
brcm63xx: switch to 4.1
Switch brcm63xx to 4.1 to give it some initial testing, but keep 3.18
at least until CC-final is out.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46386
Jonas Gorski [Wed, 15 Jul 2015 14:41:45 +0000 (14:41 +0000)]
xtables-addons: update to 2.7 to fix compilation with 4.1
Also drop the configure (not .ac) patch part as autoreconf will
overwrite it anyway with a newly generated version.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Acked-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 46385
Luka Perkov [Wed, 15 Jul 2015 08:23:28 +0000 (08:23 +0000)]
rpcd: update to the latest version
This update adds a couple of file plugin enhancements, such as base64 support
and setting mode when files are written.
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 46384
Felix Fietkau [Wed, 15 Jul 2015 08:17:49 +0000 (08:17 +0000)]
scripts/ipkg-build: fix a build regression introduced in r46360 (fixes #20082)
go to the $TOPDIR directory before trying to extract a git/svn timestamp
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46383
Felix Fietkau [Wed, 15 Jul 2015 08:17:42 +0000 (08:17 +0000)]
ar8216: add swconfig attributes for ARL table flushing
Add swconfig attributes for flushing the ARL table globally or per port.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 46382
Felix Fietkau [Wed, 15 Jul 2015 08:17:36 +0000 (08:17 +0000)]
ar8216: adjust ATU flushing in case of link changes
If a link goes down, don't flush the complete ARL table.
Only flush the entries for the respective port.
Don't touch ARL table if a link goes up.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 46381
Felix Fietkau [Wed, 15 Jul 2015 08:17:28 +0000 (08:17 +0000)]
ar8216: add ARL table flushing per port
Adds functions for flushing ARL table entries per port.
Successfully tested on AR8327. Implementation for AR8216/AR8236/AR8316
is based on the AR8236 datasheet and assumes that the three chips
share a common ATU register layout.
Compile-tested only for AR8216/AR8236/AR8316.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 46380
Felix Fietkau [Wed, 15 Jul 2015 08:17:23 +0000 (08:17 +0000)]
ar8216: add reading ARL table for AR8216/AR8236/AR8316
Adds the chip-specific part of reading ARL table for AR8216/AR8236/AR8316.
It's based on the AR8236 datasheet and compile-tested only as I couldn't
find datasheets for AR8216/AR8316 and don't own devices with these chips.
The existing ar8216_atu_flush implementation was used for all three
chip types, therefore I guess they share a common ATU register layout.
More testing would be appreciated.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 46379
Felix Fietkau [Wed, 15 Jul 2015 08:16:40 +0000 (08:16 +0000)]
tools/e2fsprogs: add a darwin-compat patch
On darwin we need to import stdint to get these integer typedefs.
Patch by: Lawrence D'Anna <larry@elder-gods.org>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46378
Felix Fietkau [Wed, 15 Jul 2015 08:16:22 +0000 (08:16 +0000)]
wpa-supplicant: add 802.11r client support
Add 802.11r client support to wpa_supplicant. It's only enabled in
wpa_supplicant-full. hostapd gained 802.11r support in commit r45051.
Tested on a TP-Link TL-WR710N sta psk client with two 802.11r enabled
openwrt accesspoints (TP-Link TL-WDR3600).
Signed-off-by: Stefan Hellermann <stefan@the2masters.de>
SVN-Revision: 46377
Steven Barth [Wed, 15 Jul 2015 07:38:54 +0000 (07:38 +0000)]
odhcpd: also unify router and DNS lifetimes
Signed-off-by: Steven Barth <steven@midlink.org>
SVN-Revision: 46376
Steven Barth [Wed, 15 Jul 2015 06:57:43 +0000 (06:57 +0000)]
odhcpd: fix RA lifetime calculation
Signed-off-by: Steven Barth <steven@midlink.org>
SVN-Revision: 46375
Jo-Philipp Wich [Tue, 14 Jul 2015 22:27:39 +0000 (22:27 +0000)]
scripts/feeds: return error status from feed update
This patch is a modified version of the patch being discussed at here:
https://patchwork.ozlabs.org/patch/471303/
from Martin Strbacka <martin.strbacka@nic.cz>
My version modifies scripts/feeds so that an error with one of the feeds just
raises the error flag, but script continues and tries to update the other
feeds. After all feeds have been updated, the script returns 1 if at least
one feed failed, and 0 on success with all feeds. The user can then utilise
the status in his build script, if he wants.
signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
SVN-Revision: 46374
Hauke Mehrtens [Tue, 14 Jul 2015 20:56:04 +0000 (20:56 +0000)]
robocfg: remove robocfg
This controls the old Broadcom switch driver which was removed over a
year ago, since then this is useless. Use swconfig instead it works
with more (Broadcom) switches.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46373
Hauke Mehrtens [Tue, 14 Jul 2015 20:52:18 +0000 (20:52 +0000)]
adm5120: do not config something as module
All modules should be build by a package and only selected by such a
package. Remove all the config options selected as module and also
refresh the config.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46372
Hauke Mehrtens [Tue, 14 Jul 2015 20:51:37 +0000 (20:51 +0000)]
admswconfig: fix compile with musl
caddr_t is not defined everywhere any more, cast it the the real
pointer type of ifr_data.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46371
Steven Barth [Tue, 14 Jul 2015 20:10:46 +0000 (20:10 +0000)]
odhcpd: use 65535s as default lifetime and make interval configurable
Signed-off-by: Steven Barth <steven@midlink.org>
SVN-Revision: 46370
Hauke Mehrtens [Tue, 14 Jul 2015 18:51:23 +0000 (18:51 +0000)]
bcm53xx: fix usb3 build with kernel 4.1
One argument was removed with kernel 4.1 from xhci_handshake() which
caused a compile error.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46369
Jo-Philipp Wich [Tue, 14 Jul 2015 17:23:56 +0000 (17:23 +0000)]
linux: enable kmod-acpi-button for x86_64 (#20080)
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 46368
John Crispin [Tue, 14 Jul 2015 16:24:10 +0000 (16:24 +0000)]
brcm2708: partially revert r46347 to fix sysupgrade
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 46367
John Crispin [Tue, 14 Jul 2015 16:24:02 +0000 (16:24 +0000)]
x86: add kmod-acpi-button and kmod-button-hotplug to default packages
Since r40909 openwrt can automatically shutdown when you press the
power button or try to shutdown a kvm virtual machine.
When booting a recent CC-rc2 or trunk image, it doesn't work,
as two kernel modules are missing.
Add these two kernel modules to the default packages, so users
don't need to install them manually.
Signed-off-by: Stefan Hellermann <stefan@the2masters.de>
SVN-Revision: 46366
Felix Fietkau [Tue, 14 Jul 2015 10:30:38 +0000 (10:30 +0000)]
ccache: Make ccache aware of OpenWRT provided GCC patch.
The OpenWRT GCC patch, 910-mbsd_multi.patch adds an extra option
to gcc that depends on an environment variable. Standard ccache
is unaware of this option and therefor can produce stdout from gcc
that doesn't correspond to what you would get if you actually
do a direct compilation with gcc.
This commit adds a patch to ccache to make it aware of the new
option and removes the feature from the ccache package to use the
host system's installed ccache binary.
Signed-off-by: Karl Vogel <karl.vogel@gmail.com>
SVN-Revision: 46364
Rafał Miłecki [Tue, 14 Jul 2015 10:25:46 +0000 (10:25 +0000)]
bcm53xx: add early support for Netgear R7000
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 46363
John Crispin [Tue, 14 Jul 2015 09:57:52 +0000 (09:57 +0000)]
scripts: fix 64bit uclibc external toolchain detection
according to gcc, UCLIBC_DYNAMIC_LINKER64
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 46362
John Crispin [Tue, 14 Jul 2015 09:57:45 +0000 (09:57 +0000)]
build: Prevent more gzip timestamps
To improve reproducibility, prevent the inclusion of timestamps
in the gzip header.
Signed-off-by: Reiner Herrmann <reiner@reiner-h.de>
SVN-Revision: 46361
John Crispin [Tue, 14 Jul 2015 09:57:19 +0000 (09:57 +0000)]
ipkg-build: use deterministic timestamps in ipk tarballs
As a follow-up to r46026, this commit sets the modification
times of files inside the tarballs to deterministic values.
It uses the date of the last git or svn commit and falls
back to the old behavior if those are not available.
Signed-off-by: Reiner Herrmann <reiner@reiner-h.de>
SVN-Revision: 46360
John Crispin [Tue, 14 Jul 2015 09:57:08 +0000 (09:57 +0000)]
ramips: added gpio spi refclk support for wrtnode board
This syncs the dts file with the one provided by the wrtnode team:
https://github.com/WRTnode/openwrt-patches/blob/master/R41508/wrtnode_factory_firmware_dts.patch
Signed-off-by: Christian Mehlis <christian@m3hlis.de>
SVN-Revision: 46359
John Crispin [Tue, 14 Jul 2015 09:56:59 +0000 (09:56 +0000)]
swconfig: Split libsw out of swconfig for reuse in other packages
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
SVN-Revision: 46358
Steven Barth [Tue, 14 Jul 2015 09:12:29 +0000 (09:12 +0000)]
odhcpd: unsolicited unicast RAs + fix NDP-relay
odhcpd now sends unsolicited RAs also via unicast to known link-local
neighbors. This is an attempt to work-around common smartphone issues
https://code.google.com/p/android/issues/detail?id=32662
Also NDP-relay should now work more reliably now
Signed-off-by: Steven Barth <steven@midlink.org>
SVN-Revision: 46357
John Crispin [Tue, 14 Jul 2015 07:44:14 +0000 (07:44 +0000)]
ubox: update to latest git HEAD
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 46356
John Crispin [Tue, 14 Jul 2015 07:43:50 +0000 (07:43 +0000)]
toolchain: fix gcc 4.6 build with gcc5
build error:
cfns.gperf:101:1: error: 'gnu_inline' attribute present on 'libc_name_p'
cfns.gperf:26:14: error: but not here
observed on Arch Linux
affected versions gcc 4.6, gcc 4.7
reported & fixed in DragonFlyBSD issue #136
https://github.com/DragonFlyBSD/DPorts/issues/136
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 46355
John Crispin [Tue, 14 Jul 2015 07:43:33 +0000 (07:43 +0000)]
gemini: switch to 4.1
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 46354
John Crispin [Tue, 14 Jul 2015 07:43:10 +0000 (07:43 +0000)]
gemini: add 4.1 support
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 46353
John Crispin [Tue, 14 Jul 2015 07:42:18 +0000 (07:42 +0000)]
gemini: add NAS packages to Raidsonic profile
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 46352
John Crispin [Tue, 14 Jul 2015 07:41:43 +0000 (07:41 +0000)]
gemini: copy kernel image to BIN_DIR
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 46351
John Crispin [Tue, 14 Jul 2015 07:41:19 +0000 (07:41 +0000)]
ramips: added led support for wrtnode board
This syncs the dts file with the one provided by the wrtnode team:
https://github.com/WRTnode/openwrt-patches/blob/master/R41508/wrtnode_factory_firmware_dts.patch
Signed-off-by: Christian Mehlis <christian@m3hlis.de>
SVN-Revision: 46350
John Crispin [Tue, 14 Jul 2015 07:40:22 +0000 (07:40 +0000)]
ramips: adding support for OY-0001 Wireless Router
Adding support for OY-0001 Wireless Router.
OY-0001 is a wireless router made by oyewifi.com. Below is the details:
MT7620A, 128MB DDR2, 16MB FLASH, SD Slot, USB 2.0, 4 x LAN + 1 x WAN.
Signed-off-by: Tom Deng <2579131212@qq.com>
SVN-Revision: 46349
John Crispin [Tue, 14 Jul 2015 07:39:19 +0000 (07:39 +0000)]
ramips: mt7620 ArcherC20i USB support
USB port of TP-Link Archer C20i does not work with trunk and CC.
This patch adds two nodes (ehci and ohci) to the device tree enabling USB.
Signed-off-by: Gunnar Thorburn <gunnar@thorburn.se>
SVN-Revision: 46348
John Crispin [Tue, 14 Jul 2015 07:39:10 +0000 (07:39 +0000)]
brcm2708: Implement sysupgrade
Implement sysupgrade for Raspberry Pi, similar to the way it is done on x86:
The config files are saved in the boot partition and moved to where they are
normally expected in preinit.
Also add optional gzip compression for the SD card image, since this can save
a lot of space (76M vs 6M), also similar to x86.
Signed-off-by: Bruno Randolf <br1@einfach.org>
SVN-Revision: 46347
John Crispin [Tue, 14 Jul 2015 07:38:47 +0000 (07:38 +0000)]
kernel: fix build with CONFIG_MTD unset
Fixed typo in the patch provided by Hauke:
https://lists.openwrt.org/pipermail/openwrt-devel/2015-July/034274.html
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 46346
John Crispin [Tue, 14 Jul 2015 07:38:33 +0000 (07:38 +0000)]
generic: add missing symbol
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 46345
John Crispin [Tue, 14 Jul 2015 07:37:29 +0000 (07:37 +0000)]
brcm2708: add DT support
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 46344
John Crispin [Tue, 14 Jul 2015 07:37:14 +0000 (07:37 +0000)]
brcm2708-gpu-fw: update to latest version
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 46343
John Crispin [Tue, 14 Jul 2015 07:37:03 +0000 (07:37 +0000)]
ar71xx: add support for the devolo dLAN pro 1200+ WiFi ac
Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de>
SVN-Revision: 46342
John Crispin [Tue, 14 Jul 2015 07:35:59 +0000 (07:35 +0000)]
base-files: added option to configure the gpio led trigger in uci-defaults
Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de>
SVN-Revision: 46341
John Crispin [Tue, 14 Jul 2015 07:35:45 +0000 (07:35 +0000)]
mac80211: make ath10k firmware v2 selectable
Added option for old firmware version (10.1 API v2). It seems that recent
firmware versions are constantly crashing (at least on a QCA9880-BR4A-R) and
this provides the option to select an older version instead.
Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de>
SVN-Revision: 46340
John Crispin [Tue, 14 Jul 2015 07:34:31 +0000 (07:34 +0000)]
ar71xx: add support to use gpio irqs
Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de>
SVN-Revision: 46339
John Crispin [Tue, 14 Jul 2015 07:32:33 +0000 (07:32 +0000)]
ar71xx: add support for the devolo dLAN pro 500 Wireless+
Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de>
SVN-Revision: 46338
projects / openwrt / staging / dangole.git / log