spi: cadence_qspi_apb: Support 32 bit AHB address

AHB address can be as long as 32 bit, hence remove the
CQSPI_REG_INDIRECTRDSTARTADDR mask. Since AHB address is passed from DT
and read as u32 value, it anyway does not make sense to mask upper bits.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagan Teki <jteki@openedev.com>

defconfig: k2g_evm_defconfig: enable SPI driver model

Enable SPI and SPI Flash driver model as K2G SPI controller driver
supports driver model.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>

ARM: dts: k2g: add support for Davinci SPI controller

K2G SoC has 4 SPI instances that are compatible with davinci_spi
controller(present on previous generation of Keystone2 devices). Add DT
nodes for the same. K2G EVM has a N25Q128A13 SPI NOR flash connected on
SPI-1. Add DT bindings for the same.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>

defconfig: k2l_evm_defconfig: enable SPI driver model

Enable SPI and SPI Flash driver model as K2L SPI controller driver
supports driver model.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>

ARM: dts: k2l: Enable Davinci SPI controller

Now that davinci_spi driver has been converted to DM framework, enable
the same in DT. Also add "spi-flash" as compatible property to
n25q128a11 node as it is required for flash device to be probed in
U-Boot.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>

defconfig: k2e_evm_defconfig: enable SPI driver model

Enable SPI and SPI Flash driver model as K2E SPI controller driver
supports driver model.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>

ARM: dts: k2e: Enable Davinci SPI controller

Now that davinci_spi driver has been converted to DM framework, enable
the same in DT. Also add "spi-flash" as compatible property to
n25q128a11 node as it is required for flash device to be probed in
U-Boot.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>

defconfig: k2hk_evm_defconfig: enable SPI driver model

Enable SPI and SPI Flash driver model as K2HK SPI controller driver
supports driver model.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>

ARM: dts: k2hk: Enable Davinci SPI controller

Now that davinci_spi driver has been converted to DM framework, enable
the same in DT. Also add "spi-flash" as compatible property to
n25q128a11 node as it is required for flash device to be probed in
U-Boot.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>

ARM: dts: keystone2: add SPI aliases for davinci SPI nodes

Add aliases for SPI nodes in order for it to be probed by the DM
framework.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>

keystone2: spi: do not define DM_SPI and DM_SPI_FLASH for SPL build

Since Keystone2 devices do not have support DM in SPL, do not define
DM_SPI and DM_SPI_FLASH for SPL build.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>

spi: davinci_spi: Convert to driver to adapt to DM

Convert davinci_spi driver so that it complies with SPI DM framework.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>

dm: core: implement dev_map_physmem()

This API helps to map physical register addresss pace of device to
virtual address space easily. Its just a wrapper around map_physmem()
with MAP_NOCACHE flag.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Suggested-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>

spi: spi-uclass: fix typo in debug output

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Jagan Teki <jteki@openedev.com>

Merge git://git.denx.de/u-boot-arc

arc: make global_data.h usable in assembly files

Currently on attempt to use global_data.h in an assembly file following
will happen:
-------------------->8-----------------
./arch/arc/include/asm/global_data.h: Assembler messages:
./arch/arc/include/asm/global_data.h:11: Error: bad instruction 'struct arch_global_data{'
./arch/arc/include/asm/global_data.h:12: Error: junk at end of line, first unrecognized character is `}'
scripts/Makefile.build:316: recipe for target 'arch/arc/lib/start.o' failed
-------------------->8-----------------

In this change we disable struct arch_global_data in ASM which fixes
the issue above.

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>

arc: Use "-mcpu=archs" instead of deprecated "-marchs" for ARC HS

Newer ARC toolchains don't support "-marchs" option any longer.
Instead "-mcpu=archs" should be used. What's also important older
toiolchains that support ARC HS cores will also happily accept
"-mcpu=archs" so that's a very safe move.

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>

Merge branch 'master' of git.denx.de/u-boot-sunxi

sunxi: Add defconfig and DTS file for Allwinner R16 EVB (Parrot)

The Parrot Board is an evaluation board with an Allwinner R16 (assumed
to be close to an Allwinner A33), 4GB of eMMC, 512MB of RAM, USB host
and OTG, a WiFi/Bluetooth combo chip, a micro SD Card reader, 2
controllable buttons, an LVDS port with separated backlight and
capacitive touch panel ports, an audio/microphone jack, a camera CSI
port, 2 sets of 22 GPIOs and an accelerometer.

The DTS file is identical to the one submitted to the upstream kernel.

Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

sunxi: Add missing boot_media fields in the SPL header

Commit b19236fd1 ("sunxi: Increase SPL header size to 64 bytes to avoid
code corruption") Added defines for MMC0 and SPI as boot identification.
After verifying on an OLinuXino Lime2 with NAND and eMMC, the expected
values have been confirmed and added to spl.h

Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

sunxi: spl: Fix DRAM info printing

The switch to simple_printf was causing the SPL dram info to show as:

DRAM: u MiB

This fixes this by switching from %lu to %d for printing the DRAM size.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

Merge branch 'master' of git://git.denx.de/u-boot-usb

Merge branch 'master' of git://git.denx.de/u-boot-socfpga

Prepare v2016.07-rc3

Signed-off-by: Tom Rini <trini@konsulko.com>

Merge branch 'master' of git://git.denx.de/u-boot-uniphier

mmc: increase MMC SDHCI read status timeout

Otherwise,  ocassionally see errors like this:
  Flashing sparse image at offset 2078720
  Flashing Sparse Image
  sdhci_send_command: Timeout for status update!
  mmc fail to send stop cmd
  write_sparse_image: Write failed, block #2181088 [0]

This does not affect the actual writing speed, which is controlled by
the default value:
  CONFIG_SDHCI_CMD_DEFAULT_TIMEOUT

It only increases the retries when reading:
  SDHCI_INT_STATUS
to avoid the timeout error.

Signed-off-by: Steve Rae <steve.rae@raedomain.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>

ti_omap5_common: Find right dtb file for DRA72-RevC Evm

DRA72-Evm revC uses dra72-evm-revc.dtb. Update the same in env vatiables.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

autoboot: move bootdelay >= 0 check to abortboot()

Move the bootdelay >= 0 check to the caller, which simplifies
the callees.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>

autoboot: move CONFIG_SILENT_CONSOLE handling

Factor out the same code from the callees to the caller.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>

autoboot: rename abortboot_{keyed, normal} to __abortboot

Because abortboot_keyed() and abortboot_normal() are not compiled
at the same time, we can rename both of them to __abortboot().
This allows to drop #ifdef from the caller.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>

autoboot: remove CONFIG_ZERO_BOOTDELAY_CHECK

As the help message of CONFIG_BOOTDELAY says, CONFIG_BOOTDELAY=-2
means the autoboot with no delay, with no abort check even if
CONFIG_ZERO_BOOTDELAY_CHECK is defined.

To sum up, the autoboot behaves as follows:

 [1] CONFIG_BOOTDELAY=0 && CONFIG_ZERO_BOOTDELAY_CHECK=y
    autoboot with no delay, but you can abort it by key input

 [2] CONFIG_BOOTDELAY=0 && CONFIG_ZERO_BOOTDELAY_CHECK=n
    autoboot with no delay, with no check for abort

 [3] CONFIG_BOOTDELAY=-1
    disable autoboot

 [4] CONFIG_BOOTDELAY=-2
    autoboot with no delay, with no check for abort

As you notice, [2] and [4] come to the same result, which means we
do not need CONFIG_ZERO_BOOTDELAY_CHECK.  We can control all the
cases only by CONFIG_BOOTDELAY, like this:

 [1] CONFIG_BOOTDELAY=0
    autoboot with no delay, but you can abort it by key input

 [2] CONFIG_BOOTDELAY=-1
    disable autoboot

 [3] CONFIG_BOOTDELAY=-2
    autoboot with no delay, with no check for abort

This commit converts the logic as follow:
  CONFIG_BOOTDELAY=0 && CONFIG_ZERO_BOOTDELAY_CHECK=n
    --> CONFIG_BOOTDELAY=-2

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Acked-by: Christian Riesch <christian.riesch@omicronenergy.com>
Acked-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>

doc: bootdelay: drop explanation about CONFIG_BOOTDELAY from README

The same information now exists in common/Kconfig.  Do not duplicate
documentation from the point of view of maintainability.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>

ARM: socfpga: move CONFIG_BOOTDELAY to Kconfig for IS1 board

This recently added board missed the tree-wide migration of
CONFIG_BOOTDELAY.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Pavel Machek <pavel@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>

ARM: AM437x: Align HS device variant defconfig filename

Align the name of the defconfig file for high-security (HS) device variants
from the AM43xx family of SoCs with the corresponding name used for the
general purpose devices. This allows for easier cross-association of those
files and also provides room to grow from an HS device part number
perspective.

Furthermore, update and cleanup associated MAINTAINERS file.

Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Madan Srinivas <madans@ti.com>

driver: qspi: correct QSPI disable CS reset value

Correcting QSPI disable/unselect CS reset value.
CTRL_CORE_CONTROL_IO_2: QSPI_MEMMAPPED_CS[10:8]

This is not causing any issue, but its better
to untouch the reserved bits.

Praneeth Bajjuri <praneeth@ti.com>
Signed-off-by: Ravi Babu <ravibabu@ti.com>

ARM: uniphier: add external IRQ setup code

I will carry this work-around until it is cared in the kernel.
This looks up the AIDET node and sets up a register to handle
active low interrupt signals.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

ARM: dts: uniphier: add AIDET nodes

The AIDET (ARM Interrupt Detector Add-on Circuit) is a kind of
syscon block related with the interrupt controller.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

pinctrl: uniphier: add Ethernet pin-mux settings

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

pinctrl: uniphier: avoid building unneeded pin-mux tables for SPL

SPL does not use all of the devices, so we can save some memory
footprint.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

pinctrl: uniphier: support pin configuration for dedicated pins

PH1-LD4 and PH1-sLD8 SoCs have pins that support pin configuration
(pin biasing, drive strength control), but not pin-muxing.

Allow to fill the mux value table with -1 for those pins; pins with
mux value -1 will be skipped in the pin-mux set function.  The mux
value type should be changed from "unsigned" to "int" in order to
accommodate -1 as a special case.

[ Linux commit: 363c90e743b50a432a91a211dd8b078d9df446e9 ]

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

pinctrl: uniphier: split pinctrl driver for PH1-LD11 and PH1-LD20

PH1-LD11 and PH1-LD20 have much pin controlling in common, so I
added a single driver shared between them in the initial commit.

However, the Ethernet pin-mux settings I am going to add are
different with each other, and they may diverge more as the
progress of development.  Split it into two dedicated drivers.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

pinctrl: uniphier: allow to have pinctrl node under syscon node

Currently, the UniPhier pinctrl driver itself is a syscon, but it
turned out much more reasonable to make it a child node of a syscon
because our syscon node consists of a bunch of system configuration
registers, not only pinctrl, but also phy, and misc registers.
It is difficult to split the node.  This commit allows to migrate to
the new DT structure.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

ARM: dts: uniphier: sync Device Trees with upstream Linux

I periodically sync Device Trees for better maintainability.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

pinctrl: uniphier: remove unneeded pin group nand_cs1

This SoC does not support NAND CS1.  This place-holder is no longer
necessary.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

pinctrl: uniphier: fix NAND pin-mux setting for PH1-LD11/LD20

My mistake in the initial support patch.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

pinctrl: uniphier: remove wrong pin-mux functions for ProXstream2

These are pin group names, not function names.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

ARM: uniphier: fix typo "talbe"

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

x86: coreboot: Remove the dummy pch driver

There is a dummy pch driver in the coreboot directory. This causes
drivers of its children fail to function due to empty ops. Remove
the whole file since it is no longer needed.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Merge git://git.denx.de/u-boot-fsl-qoriq

configs: Re-sync after boot menu changes

Signed-off-by: Tom Rini <trini@konsulko.com>

armv8: dts: fsl: Remove cpu nodes from Layerscape DTSIs

Currently layescape SoCs are not using cpu nodes. So removing
them in favour of compatibly with  similar SoCs that
have different cores like LS2080A and LS2088A.

This has been tested on LS2080AQDS, LS1043ARDB, LS1012ARDB.

Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Abhimanyu Saini <abhimanyu.saini@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

armv8: fsl-layerscape: Append "A" in SoC name for ARM based SoCs

Freescale ARMv8 SoC name ends with "A" to represent ARM SoCs.
like LS2080A, LS1043A, LS1012A.

So append "A" to SoC names.

Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

mmc: fsl: introduce wp_enable

Introudce wp_enable. To check WPSPL, wp_enable needs to be set
to 1 in board code.

Take i.MX6UL for example, for some boards, they do not use WP singal,
so they does not configure USDHC1_WP_SELECT_INPUT, and its default
value is 0(GPIO1_IO02). However GPIO1_IO02 is muxed for i2c usage and
SION bit set. So USDHC controller can always get wp signal and WPSPL
shows write protect and blocks driver continuing. This is not what
we want to see, so add wp_enable, and if set to 0, just omit the
WPSPL checking and this does not effect normal working of usdhc
controller.

If wp-gpios is provided in dts, wp_enable is set to 1, otherwise 0.

Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

fsl_esdhc: Update clock enable bits for USDHC

The USDHC moves the 4 clock bits CARD_CLK_SOFT_EN, IPG_PERCLK_SOFT_EN,
HCLK_SOFT_EN, and IPG_CLK_SOFT_EN from sysctl register to vendorspec
register. The driver uses RSTA to replace the clock gate off
operation. But this is not a good solution because:
1. when using RSTA, we should wait this bit to clear by itself. This is not
   implemeneted in the code.
2. After RSTA is set, it is recommended that the Host Driver reset the
   external card and reinitialize it.

So in this patch, we change to use the vendorspec registers for these bits
operation.

Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

mmc: fsl: reset to normal boot mode when eMMC fast boot

When booting in eMMC fast boot, MMC host does not exit from
boot mode after bootrom loading image. So the first command
'CMD0' sent in uboot will pull down the CMD line to low and
cause errors.

This patch cleans the MMC boot register in "mmc_init" to put the
MMC host back to normal mode.

Also clear DLL_CTRL delay line settings at USDHC initialization
to eliminate the pre-settings from boot rom.

Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

armv8: ls1043aqds: print FPGA info early for QSPI boot

Now I2C is initialized early enough to access FPGA so it supports to
show board info as early as other boot methods.

Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

armv8: ls1043aqds: use configurable clock

Get the clocks from FPGA through I2C, if IFC is disabled.

Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

common: add new boot media kconfig entry

Add CONFIG_{SD|NAND|ONENAND|SPI|QSPI|SATA}_BOOT kconfig entries.

SoCs supports loading U-Boot from different medias to DRAM, such as
i.MX6/7 supports loading U-Boot to DRAM from sd/emmc/nand/qspi/spi/sata
and etc. For i.MX, imximage will generate different IVT headers according
to boot medias.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Christophe Ricard <christophe-h.ricard@st.com>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Francois Retief <fgretief@spaceteq.co.za>
Cc: Tom Rini <trini@konsulko.com>

Kconfig: make NOR_BOOT a common option

Not only am335x supports booting from NOR, i.MX6 SoCs also
supports booting from NOR. Make NOR_BOOT a common
option to let different SoCs share it.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Christophe Ricard <christophe-h.ricard@st.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Francois Retief <fgretief@spaceteq.co.za>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

maintainers: new email address

Update the email address for the boards that I maintain.

Signed-off-by: Steve Rae <steve.rae@raedomain.com>

fastboot: sparse: improve CHUNK_TYPE_FILL write performance

- increase the size of the fill buffer
- testing has shown a 10x improvement when the sparse image
  has large CHUNK_TYPE_FILL chunks

Signed-off-by: Steve Rae <srae@broadcom.com>

fastboot: sparse: implement reserve()

In order to process the CHUNK_TYPE_DONT_CARE properly, there is
a requirement to be able to 'reserve' a specified number of blocks
in the storage media. Because of the special handling of "bad blocks"
in NAND devices, this is implemented in a storage abstraction function.

Signed-off-by: Steve Rae <srae@broadcom.com>
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>

fastboot: sparse: resync common/image-sparse.c (part 2)

- update fastboot_okay() and fastboot_fail()

This file originally came from upstream code.

While retaining the storage abstraction feature, this is the second
set of the changes required to resync with the
  cmd_flash_mmc_sparse_img()
in the file
  aboot.c
from
  https://us.codeaurora.org/cgit/quic/la/kernel/lk/plain/app/aboot/aboot.c?h=LE.BR.1.2.1

Signed-off-by: Steve Rae <srae@broadcom.com>

fastboot: sparse: resync common/image-sparse.c (part 1)

This file originally came from upstream code.

While retaining the storage abstraction feature, this is the first
set of the changes required to resync with the
  cmd_flash_mmc_sparse_img()
in the file
  aboot.c
from
  https://us.codeaurora.org/cgit/quic/la/kernel/lk/plain/app/aboot/aboot.c?h=LE.BR.1.2.1

Signed-off-by: Steve Rae <srae@broadcom.com>

fastboot: sparse: remove session-id logic

This "session-id" alogrithm is not required, and currently corrupts
the stored image whenever more the one "session" is required.

Signed-off-by: Steve Rae <srae@broadcom.com>

Merge branch 'master' of git://git.denx.de/u-boot-samsung

mmc: dw_mmc: fix the wrong AND operation

These condition checking are wrong.
Original Author's intention might be "&" instead of "&&".
It can know whether receive or transmit data request with
BIT[4]/BIT[5] of RINTSTS register.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

arm: at91: taurus/axm: add DM and DTS support

add DM and DTS support for the at91 based siemens
boards.

Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
[rebased on current ToT]
Signed-off-by: Andreas Bießmann <andreas@biessmann.org>

arm: at91: smartweb: add DM and DTS support

Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
[rebased on current ToT]
Signed-off-by: Andreas Bießmann <andreas@biessmann.org>

arm: at91: dts: Bring in dts files for AT91SAM9G20 and SAM9260

Add this files from Linux v4.6-rc5

66b8a424d: [workqueue: fix ghost PENDING flag while doing MQ IO]

Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Andreas Bießmann <andreas@biessmann.org>

corvus DTS / DM support

Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
[rebase on current ToT, don't delete gurnard DTB creation]
Signed-off-by: Andreas Bießmann <andreas@biessmann.org>

arm: at91: add CONFIG_AT91SAM9M10G45

add support for CONFIG_AT91SAM9M10G45.

Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>

ARM: at91: Don't invoke spl_boot_device() twice

Since the spl_boot_mode() is now passed the boot device to boot from,
make use of it instead of inquiring for the boot device again. This
allows board_boot_order() to function correctly.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>

common: Pass the boot device into spl_boot_mode()

The SPL code already knows which boot device it calls the spl_boot_mode()
on, so pass that information into the function. This allows the code of
spl_boot_mode() avoid invoking spl_boot_device() again, but it also lets
board_boot_order() correctly alter the behavior of the boot process.

The later one is important, since in certain cases, it is desired that
spl_boot_device() return value be overriden using board_boot_order().

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
[add newly introduced zynq variant]
Signed-aff-by: Andreas Bießmann <andreas@biessmann.org>

ehci: mx7: fix otg id detection

The USBNC_PHYCFG2_ACAENB bit should be cleared to enable the
OTG ID detection, not set it. When the bit is set, the ACA
Resistance Detection is enabled, which disables the OTG ID
detection, because the internal pull up is off.

Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>

ehci: mx7: fix usbnc_regs

There is a 4 bytes hole between phy_cfg2 and phy_status, fix the
usbnc_regs structure to include the hole.

Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>

usb: fsl: Fix NULL terminating issue for usb controller name string

Fixes NULL terminating issue for usb controller name string by using
sizeof operator.

Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>

kbuild: avoid race between dtbs and dt/dt.dtb targets

If the final targets depend on both "dtbs" and "dts/dt.dtb",
and -j option is given to the command line, multiple threads
descend into the dts/ directory, which causes build error.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Andreas Dannenberg <dannenberg@ti.com>

efi_loader: Fix typo in distro script

The distro script is supposed to use the internal fdt as fallback if we
find no viable other option. However, we're missing a space key to actually
make that work.

Add the space, so we can successfully load an EFI blob even when there is
no device tree provided on the target device.

Signed-off-by: Alexander Graf <agraf@suse.de>

board/BuR: rename kwb board to brxre1

Rename B&R kwb board to brxre1

Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Tom Rini <trini@konsulko.com>

board/BuR: rename tseries board to brppt1

Rename B&R tseries board to brppt1

Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Tom Rini <trini@konsulko.com>

arm: bcm235xx: update clock framework

The handling of the "usage counter" is incorrect, and the clock should
only be disabled when transitioning from 1 to 0.

Reported-by: Chris Brand <chris.brand@broadcom.com>
Signed-off-by: Steve Rae <srae@broadcom.com>

arm: bcm235xx: fix kps ccu

The Kona Peripheral Slave CCU has 4 policy mask registers, not 8.

Signed-off-by: Chris Brand <chris.brand@broadcom.com>
Signed-off-by: Steve Rae <srae@broadcom.com>

arm: bcm235xx: implement the boot0 hook code

Choose the Kconfig boot0 hook option and implement the required code.

Signed-off-by: Steve Rae <srae@broadcom.com>

arm: bcm235xx: choose 8-bit phy bus width

The Kona PHY supports an 8-bit wide UTMI interface,
therefore, choose this Kconfig setting.

Signed-off-by: Steve Rae <srae@broadcom.com>

clk: sandbox: don't check clk ID against 0

clk->id is unsigned, so it can't be < 0. Remove the check for that.

FWIW, this issue was introduced when the clock API converted e.g.
clk_get_rate()'s clock ID parameter from an int to an unsigned long
(with a struct clk), without removing this check.

Fixes: 135aa9500264 ("clk: convert API to match reset/mailbox style")
Reported-by: Coverity Scan
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>

common: Fix support for environment file in EXT4

Signed-off-by: Andrej Rosano <andrej@inversepath.com>

ARM: armv7: refactor Makefile slightly

Use Kbuild standard style where possible.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

hush: complete renaming CONFIG_SYS_HUSH_PARSER to CONFIG_HUSH_PARSER

There is no more define of CONFIG_SYS_HUSH_PARSER.  Rename some
remaining references and drop the backward compatible Kconfig entry.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Move CONFIG_SYS_HUSH_PARSER to Kconfig for last 4 boards

I still see some defines of this config in board headers.  Move them
to defconfigs (+ renaming to CONFIG_HUSH_PARSER) to complete this
migration.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

mtd: nand: Drop a blank line in nand_wait()

This empty line should not be there. Remove it.
Signed-off-by: Andre Renaud <andre@designa-electronics.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
Signed-off-by: Simon Glass <sjg@chromium.org>

ARM: move #ifdef to match the error handling code

Match the #ifdef ... #endif and the code,

   ret = do_something();
   if (ret)
           return ret;

This will make it easier to add more #ifdef'ed code.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

arm64: optimize smp_kick_all_cpus

gic_kick_secondary_cpus can directly return to the caller of
smp_kick_all_cpus.  We do not have to use x29 register here.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: York Sun <york.sun@nxp.com>

lib/lzo: bugfix when input data is not compressed

When the input data is not compressed at all,
lzo1x_decompress_safe will fail, so call memcpy()
instead.

Signed-off-by: Joris Lijssens <joris.lijssens@gmail.com>

env: avoid build error for boards without CONFIG_SYS_{CPU, BOARD}

If CONFIG_ENV_VARS_UBOOT_CONFIG is enabled (it is by distro), this
code causes build error for boards without CONFIG_SYS_{CPU,_BOARD}.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Respect SOURCE_DATE_EPOCH when building FIT images.

Embedding timestamps in FIT images results in unreproducible builds
for targets that generate a fit image, such as dra7xx_evm.

This patch uses the SOURCE_DATE_EPOCH environment variable, when set,
to use specified value for the date.

Thanks to HW42 for debugging the issue and providing the patch:

  https://lists.alioth.debian.org/pipermail/reproducible-builds/Week-of-Mon-20160606/005722.html

For more information about reproducible builds and the
SOURCE_DATE_EPOCH specification:

  https://reproducible-builds.org/specs/source-date-epoch/
  https://reproducible-builds.org/

Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Simon Glass <sjg@chromium.org>

Use C locale when setting CC_VERSION_STRING and LD_VERSION_STRING.

The output reported may be locale-dependent, which results in
unreproducible builds.

  $ LANG=C ld --version | head -n 1
    GNU ld (GNU Binutils for Debian) 2.26

  $ LANG=it_CH.UTF-8 ld --version | head -n 1
    ld di GNU (GNU Binutils for Debian) 2.26

Forcing LC_ALL=C ensures the output is consistant regardless of the
build environment.

Thanks to HW42 for debugging the issue:

  https://lists.alioth.debian.org/pipermail/reproducible-builds/Week-of-Mon-20160606/005722.html

For more information about reproducible builds:

  https://reproducible-builds.org/

Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Tom Rini <trini@konsulko.com>

board: amlogic: Rename folder for Amlogic boards

s/hardkernel/amlogic/ to have a single place for all the amlogic-based
boards.

Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Acked-by: Beniamino Galvani <b.galvani@gmail.com>

configs: gxbb: Introduce a common config header file

Introduce a meson-gxbb-common.h header file and derive the
configuration for Hardkernel Odroid-C2 board from that.

Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Acked-by: Beniamino Galvani <b.galvani@gmail.com>

common: image: minimal android image iminfo support

We already support iminfo for other images. The idea
of this patch is start to have a minimal support for
android image format. We still need to print id[] array

Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>