git.openwrt.org Git - openwrt/staging/blogic.git/log

sh: sh7269: remove nonexistent GPIO_PH[0-7] to fix pinctrl registration

Pinmux_pins[] is initialized through PINMUX_GPIO(), using designated
array initializers, where the GPIO_* enums serve as indices.  If enum
values are defined, but never used, pinmux_pins[] contains (zero-filled)
holes.  Such entries are treated as pin zero, which was registered
before, thus leading to pinctrl registration failures, as seen on
sh7722:

    sh-pfc pfc-sh7722: pin 0 already registered
    sh-pfc pfc-sh7722: error during pin registration
    sh-pfc pfc-sh7722: could not register: -22
    sh-pfc: probe of pfc-sh7722 failed with error -22

Remove GPIO_PH[0-7] from the enum to fix this.

Link: http://lkml.kernel.org/r/1505205657-18012-5-git-send-email-geert+renesas@glider.be
Fixes: ef0fa5331a73e479 ("sh: Add pinmux for sh7269")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Rich Felker <dalias@libc.org>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

sh: sh7264: remove nonexistent GPIO_PH[0-7] to fix pinctrl registration

Pinmux_pins[] is initialized through PINMUX_GPIO(), using designated
array initializers, where the GPIO_* enums serve as indices.  If enum
values are defined, but never used, pinmux_pins[] contains (zero-filled)
holes.  Such entries are treated as pin zero, which was registered
before, thus leading to pinctrl registration failures, as seen on
sh7722:

    sh-pfc pfc-sh7722: pin 0 already registered
    sh-pfc pfc-sh7722: error during pin registration
    sh-pfc pfc-sh7722: could not register: -22
    sh-pfc: probe of pfc-sh7722 failed with error -22

Remove GPIO_PH[0-7] from the enum to fix this.

Link: http://lkml.kernel.org/r/1505205657-18012-4-git-send-email-geert+renesas@glider.be
Fixes: 41797f75486d8ca3 ("sh: Add pinmux for sh7264")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Jacopo Mondi <jacopo+renesas@jmondi.org>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Rich Felker <dalias@libc.org>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

sh: sh7757: remove nonexistent GPIO_PT[JLNQ]7_RESV to fix pinctrl registration

Commit 3810e96056ff ("sh: modify pinmux for SH7757 2nd cut") renamed
GPIO_PT[JLNQ]7 to GPIO_PT[JLNQ]7_RESV, and removed the existing users
from the pinmux_pins[] array.

However, pinmux_pins[] is initialized through PINMUX_GPIO(), using
designated array initializers, where the GPIO_* enums serve as indices.
Hence entries were not really removed, but replaced by (zero-filled)
holes.  Such entries are treated as pin zero, which was registered
before, thus leading to pinctrl registration failures, as seen on
sh7722:

    sh-pfc pfc-sh7722: pin 0 already registered
    sh-pfc pfc-sh7722: error during pin registration
    sh-pfc pfc-sh7722: could not register: -22
    sh-pfc: probe of pfc-sh7722 failed with error -22

Remove GPIO_PT[JLNQ]7_RESV from the enum to fix this.

Link: http://lkml.kernel.org/r/1505205657-18012-3-git-send-email-geert+renesas@glider.be
Fixes: 3810e96056ffddf6 ("sh: modify pinmux for SH7757 2nd cut")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Jacopo Mondi <jacopo+renesas@jmondi.org>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Rich Felker <dalias@libc.org>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

sh: sh7722: remove nonexistent GPIO_PTQ7 to fix pinctrl registration

Patch series "sh: sh7722/sh7757i/sh7264/sh7269: Fix pinctrl registration",
v2.

Magnus Damm reported that on sh7722/Migo-R, pinctrl registration fails
with:

    sh-pfc pfc-sh7722: pin 0 already registered
    sh-pfc pfc-sh7722: error during pin registration
    sh-pfc pfc-sh7722: could not register: -22
    sh-pfc: probe of pfc-sh7722 failed with error -22

pinmux_pins[] is initialized through PINMUX_GPIO(), using designated
array initializers, where the GPIO_* enums serve as indices.  Apparently
GPIO_PTQ7 was defined in the enum, but never used.  If enum values are
defined, but never used, pinmux_pins[] contains (zero-filled) holes.
Hence such entries are treated as pin zero, which was registered before,
and pinctrl registration fails.

I can't see how this ever worked, as at the time of commit f5e25ae52fef
("sh-pfc: Add sh7722 pinmux support"), pinmux_gpios[] in
drivers/pinctrl/sh-pfc/pfc-sh7722.c already had the hole, and
drivers/pinctrl/core.c already had the check.

Some scripting revealed a few more broken drivers:
  - sh7757 has four holes, due to nonexistent GPIO_PT[JLNQ]7_RESV.
  - sh7264 and sh7269 define GPIO_PH[0-7], but don't use it with
    PINMUX_GPIO().

Patch 1 fixes the issue on sh7722, and was tested.  Patches 3-4 should
fix the issue on the other 3 SoCs, but was untested due to lack of
hardware.

This patch (of 4):

On sh7722/Migo-R, pinctrl registration fails with:

    sh-pfc pfc-sh7722: pin 0 already registered
    sh-pfc pfc-sh7722: error during pin registration
    sh-pfc pfc-sh7722: could not register: -22
    sh-pfc: probe of pfc-sh7722 failed with error -22

pinmux_pins[] is initialized through PINMUX_GPIO(), using designated array
initializers, where the GPIO_* enums serve as indices.  As GPIO_PTQ7 is
defined in the enum, but never used, pinmux_pins[] contains a
(zero-filled) hole.  Hence this entry is treated as pin zero, which was
registered before, and pinctrl registration fails.

According to the datasheet, port PTQ7 does not exist.  Hence remove
GPIO_PTQ7 from the enum to fix this.

Link: http://lkml.kernel.org/r/1505205657-18012-2-git-send-email-geert+renesas@glider.be
Fixes: 8d7b5b0af7e070b9 ("sh: Add sh7722 pinmux code")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reported-by: Magnus Damm <magnus.damm@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Cc: Rich Felker <dalias@libc.org>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm, hugetlb, soft_offline: save compound page order before page migration

This fixes a bug in madvise() where if you'd try to soft offline a
hugepage via madvise(), while walking the address range you'd end up,
using the wrong page offset due to attempting to get the compound order
of a former but presently not compound page, due to dissolving the huge
page (since commit c3114a84f7f9: "mm: hugetlb: soft-offline: dissolve
source hugepage after successful migration").

As a result I ended up with all my free pages except one being offlined.

Link: http://lkml.kernel.org/r/20170912204306.GA12053@gmail.com
Fixes: c3114a84f7f9 ("mm: hugetlb: soft-offline: dissolve source hugepage after successful migration")
Signed-off-by: Alexandru Moise <00moses.alexander00@gmail.com>
Cc: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Hillf Danton <hdanton@sina.com>
Cc: Shaohua Li <shli@fb.com>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: David Rientjes <rientjes@google.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ksm: fix unlocked iteration over vmas in cmp_and_merge_page()

In this place mm is unlocked, so vmas or list may change. Down read
mmap_sem to protect them from modifications.

Link: http://lkml.kernel.org/r/150512788393.10691.8868381099691121308.stgit@localhost.localdomain
Fixes: e86c59b1b12d ("mm/ksm: improve deduplication of zero pages with colouring")
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: Andrea Arcangeli <aarcange@redhat.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: zhong jiang <zhongjiang@huawei.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Claudio Imbrenda <imbrenda@linux.vnet.ibm.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

include/linux/mm.h: fix typo in VM_MPX definition

There's a typo in recent change of VM_MPX definition.  We want it to be
VM_HIGH_ARCH_4, not VM_HIGH_ARCH_BIT_4.

This bug does cause visible regressions.  In arch_vma_name the vmflags
are tested against VM_MPX.  With the incorrect value of VM_MPX, a number
of vmas (such as the stack) test positive and end up being marked as
"[mpx]" in /proc/N/maps instead of their correct names.

This confuses tools like rr which expect to be able to find familiar
vmas.

Fixes: df3735c5b40f ("x86,mpx: make mpx depend on x86-64 to free up VMA flag")
Link: http://lkml.kernel.org/r/20170918140253.36856-1-kirill.shutemov@linux.intel.com
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reviewed-by: Rik van Riel <riel@redhat.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Kyle Huey <me@kylehuey.com>
Cc: <stable@vger.kernel.org> [4.14+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

scripts/spelling.txt: add more spelling mistakes to spelling.txt

Here are some of the more spelling mistakes and typos that I've found
while fixing up spelling mistakes in kernel error message text over the
past eight weeks.

[akpm@linux-foundation.org: s/|/||/, per Joe]
Link: http://lkml.kernel.org/r/20170919090818.5989-1-colin.king@canonical.com
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Joe Perches <joe@perches.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kernel/params.c: align add_sysfs_param documentation with code

This parameter is named kp, so the documentation should use that.

Fixes: 9b473de87209 ("param: Fix duplicate module prefixes")
Link: http://lkml.kernel.org/r/20170919142656.64aea59e@endymion
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

alpha: fix build failures

The build of alpha allmodconfig is giving error:

arch/alpha/include/asm/mmu_context.h: In function 'ev5_switch_mm':
arch/alpha/include/asm/mmu_context.h:160:2: error:
implicit declaration of function 'task_thread_info';
did you mean 'init_thread_info'? [-Werror=implicit-function-declaration]

The file 'mmu_context.h' needed an extra header file.

Link: http://lkml.kernel.org/r/1505668810-7497-1-git-send-email-sudipm.mukherjee@gmail.com
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge branch 'for-4.14-fixes' of git://git./linux/kernel/git/tj/wq

Pull workqueue fixlet from Tejun Heo:
"Minor documentation update"

* 'for-4.14-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
Documentation: core-api: minor workqueue.rst cleanups

Merge branch 'for-4.14-fixes' of git://git./linux/kernel/git/tj/cgroup

Pull cgroup fix from Tejun Heo:
"The recent migration code updates assumed that migrations always
  execute from the top to the bottom once and didn't clean up internal
  states after each migration round; however, cgroup_transfer_tasks()
  repeats the inner steps multiple times and the garbage internal states
  from the previous iteration led to OOPS.

  Waiman fixed the bug by reinitializing the relevant states at the end
  of each migration round"

* 'for-4.14-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
  cgroup: Reinit cgroup_taskset structure before cgroup_migrate_execute() returns

Merge branch 'for-4.14-fixes' of git://git./linux/kernel/git/tj/percpu

Pull percpu fixes from Tejun Heo:
"Rather important fixes this time.

   - The new percpu area allocator had a subtle bug in how it iterates
     the memory regions and could skip viable areas, which led to
     allocation failures for module static percpu variables. Dennis
     fixed the bug and another non-critical one in stat calculation.

   - Mark noticed that the generic implementations of percpu local
     atomic reads aren't properly protected against irqs and there's a
     (slim) chance for split reads on some 32bit systems. Generic
     implementations are updated to disable irq when read size is larger
     than ulong size. This may have made some 32bit archs which can do
     atomic local 64bit accesses generate sub-optimal code. We need to
     find them out and implement arch-specific overrides"

* 'for-4.14-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
  percpu: fix iteration to prevent skipping over block
  percpu: fix starting offset for chunk statistics traversal
  percpu: make this_cpu_generic_read() atomic w.r.t. interrupts

Merge branch 'for-4.14-fixes' of git://git./linux/kernel/git/tj/libata

Pull libata fixes from Tejun Heo:
"Nothing too interesting.

  Arnd's gcc-7 warning fixes that slipped through the cracks for two
  release cycles (my bad), and two minor low level driver updates"

* 'for-4.14-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
  ahci: don't ignore result code of ahci_reset_controller()
  ata_piix: Add Fujitsu-Siemens Lifebook S6120 to short cable IDs
  ata: avoid gcc-7 warning in ata_timing_quantize

Merge tag 'usb-4.14-rc4' of git://git./linux/kernel/git/gregkh/usb

Pull USB fixes from Greg KH:
"Here are a number of USB fixes for 4.14-rc4 to resolved reported
  issues.

  There's a bunch of stuff in here based on the great work Andrey
  Konovalov is doing in fuzzing the USB stack. Lots of bug fixes when
  dealing with corrupted USB descriptors that we've never seen in
  "normal" operation, but is now ensuring the stack is much more
  hardened overall.

  There's also the usual XHCI and gadget driver fixes as well, and a
  build error fix, and a few other minor things, full details in the
  shortlog.

  All of these have been in linux-next with no reported issues"

* tag 'usb-4.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (38 commits)
  usb: dwc3: of-simple: Add compatible for Spreadtrum SC9860 platform
  usb: gadget: udc: atmel: set vbus irqflags explicitly
  usb: gadget: ffs: handle I/O completion in-order
  usb: renesas_usbhs: fix usbhsf_fifo_clear() for RX direction
  usb: renesas_usbhs: fix the BCLR setting condition for non-DCP pipe
  usb: gadget: udc: renesas_usb3: Fix return value of usb3_write_pipe()
  usb: gadget: udc: renesas_usb3: fix Pn_RAMMAP.Pn_MPKT value
  usb: gadget: udc: renesas_usb3: fix for no-data control transfer
  USB: dummy-hcd: Fix erroneous synchronization change
  USB: dummy-hcd: fix infinite-loop resubmission bug
  USB: dummy-hcd: fix connection failures (wrong speed)
  USB: cdc-wdm: ignore -EPIPE from GetEncapsulatedResponse
  USB: devio: Don't corrupt user memory
  USB: devio: Prevent integer overflow in proc_do_submiturb()
  USB: g_mass_storage: Fix deadlock when driver is unbound
  USB: gadgetfs: Fix crash caused by inadequate synchronization
  USB: gadgetfs: fix copy_to_user while holding spinlock
  USB: uas: fix bug in handling of alternate settings
  usb-storage: unusual_devs entry to fix write-access regression for Seagate external drives
  usb-storage: fix bogus hardware error messages for ATA pass-thru devices
  ...

Merge tag 'tty-4.14-rc4' of git://git./linux/kernel/git/gregkh/tty

Pull tty/serial fixes from Greg KH:
"Here are a small number (5) of patches for some reported TTY and
  serial issues. Nothing major, a documentation update, timing fix,
  error handling fix, name reporting fix, and a timeout issue resolved.

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'tty-4.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  serial: sccnxp: Fix error handling in sccnxp_probe()
  tty: serial: lpuart: avoid report NULL interrupt
  serial: bcm63xx: fix timing issue.
  mxser: fix timeout calculation for low rates
  serial: sh-sci: document R8A77970 bindings

Merge tag 'staging-4.14-rc4' of git://git./linux/kernel/git/gregkh/staging

Pull staging/IIO fixes from Greg KH:
"Here are some small staging/IIO driver fixes for 4.14-rc4

  Most of these have been in my tree for a while due to travels, sorry
  for the delay. They resolve a number of small issues reported by
  people, mostly for the iio drivers. Nothing major in here, full
  details are in the shortlog.

  All have been linux-next for a few weeks with no reported issues"

* tag 'staging-4.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (23 commits)
  staging: iio: ad7192: Fix - use the dedicated reset function avoiding dma from stack.
  iio: core: Return error for failed read_reg
  iio: ad7793: Fix the serial interface reset
  iio: ad_sigma_delta: Implement a dedicated reset function
  IIO: BME280: Updates to Humidity readings need ctrl_reg write!
  iio: adc: mcp320x: Fix readout of negative voltages
  iio: adc: mcp320x: Fix oops on module unload
  iio: adc: stm32: fix bad error check on max_channels
  iio: trigger: stm32-timer: fix a corner case to write preset
  iio: trigger: stm32-timer: preset shouldn't be buffered
  iio: adc: twl4030: Return an error if we can not enable the vusb3v1 regulator in 'twl4030_madc_probe()'
  iio: adc: twl4030: Disable the vusb3v1 rugulator in the error handling path of 'twl4030_madc_probe()'
  iio: adc: twl4030: Fix an error handling path in 'twl4030_madc_probe()'
  staging: rtl8723bs: avoid null pointer dereference on pmlmepriv
  staging: rtl8723bs: add missing range check on id
  staging: vchiq_2835_arm: Fix NULL ptr dereference in free_pagelist
  staging: speakup: fix speakup-r empty line lockup
  staging: pi433: Move limit check to switch default to kill warning
  staging: r8822be: fix null pointer dereferences with a null driver_adapter
  staging: mt29f_spinand: Enable the read ECC before program the page
  ...

Merge tag 'driver-core-4.14-rc4' of git://git./linux/kernel/git/gregkh/driver-core

Pull driver core fixes from Greg KH:
"Here are a few small fixes for 4.14-rc4.

  The removal of DRIVER_ATTR() was almost completed by 4.14-rc1, but one
  straggler made it in through some other tree (odds are, one of
  mine...) So there's a simple removal of the last user, and then
  finally the macro is removed from the tree.

  There's a fix for old crazy udev instances that insist on reloading a
  module when it is removed from the kernel due to the new uevents for
  bind/unbind. This fixes the reported regression, hopefully some year
  in the future we can drop the workaround, once users update to the
  latest version, but I'm not holding my breath.

  And then there's a build fix for a linker warning, and a buffer
  overflow fix to match the PCI fixes you took through the PCI tree in
  the same area.

  All of these have been in linux-next for a few weeks while I've been
  traveling, sorry for the delay"

* tag 'driver-core-4.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  driver core: remove DRIVER_ATTR
  fpga: altera-cvp: remove DRIVER_ATTR() usage
  driver core: platform: Don't read past the end of "driver_override" buffer
  base: arch_topology: fix section mismatch build warnings
  driver core: suppress sending MODALIAS in UNBIND uevents

Merge tag 'char-misc-4.14-rc4' of git://git./linux/kernel/git/gregkh/char-misc

Pull char/misc fixes from Greg KH:
"Here are a handful of char/misc driver fixes for 4.14-rc4.

  Nothing major, some binder fixups, hyperv fixes, and other tiny
  things.

  All of these have been sitting in my tree for way too long, sorry for
  the delay in getting them to you. All have been in linux-next for a
  few weeks, and despite some people's feeling about if linux-next
  actually tests things, I think it's a good "soak test" for patches"

* tag 'char-misc-4.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  Drivers: hv: fcopy: restore correct transfer length
  vmbus: don't acquire the mutex in vmbus_hvsock_device_unregister()
  intel_th: pci: Add Lewisburg PCH support
  intel_th: pci: Add Cedar Fork PCH support
  stm class: Fix a use-after-free
  nvmem: add missing of_node_put() in of_nvmem_cell_get()
  nvmem: core: return EFBIG on out-of-range write
  auxdisplay: charlcd: properly restore atomic counter on error path
  binder: fix memory corruption in binder_transaction binder
  binder: fix an ret value override
  android: binder: fix type mismatch warning

ahci: don't ignore result code of ahci_reset_controller()

ahci_pci_reset_controller() calls ahci_reset_controller(), which may
fail, but ignores the result code and always returns success. This
may result in failures like below

  ahci 0000:02:00.0: version 3.0
  ahci 0000:02:00.0: enabling device (0000 -> 0003)
  ahci 0000:02:00.0: SSS flag set, parallel bus scan disabled
  ahci 0000:02:00.0: controller reset failed (0xffffffff)
  ahci 0000:02:00.0: failed to stop engine (-5)
    ... repeated many times ...
  ahci 0000:02:00.0: failed to stop engine (-5)
  Unable to handle kernel paging request at virtual address ffff0000093f9018
    ...
  PC is at ahci_stop_engine+0x5c/0xd8 [libahci]
  LR is at ahci_deinit_port.constprop.12+0x1c/0xc0 [libahci]
    ...
  [<ffff000000a17014>] ahci_stop_engine+0x5c/0xd8 [libahci]
  [<ffff000000a196b4>] ahci_deinit_port.constprop.12+0x1c/0xc0 [libahci]
  [<ffff000000a197d8>] ahci_init_controller+0x80/0x168 [libahci]
  [<ffff000000a260f8>] ahci_pci_init_controller+0x60/0x68 [ahci]
  [<ffff000000a26f94>] ahci_init_one+0x75c/0xd88 [ahci]
  [<ffff000008430324>] local_pci_probe+0x3c/0xb8
  [<ffff000008431728>] pci_device_probe+0x138/0x170
  [<ffff000008585e54>] driver_probe_device+0x2dc/0x458
  [<ffff0000085860e4>] __driver_attach+0x114/0x118
  [<ffff000008583ca8>] bus_for_each_dev+0x60/0xa0
  [<ffff000008585638>] driver_attach+0x20/0x28
  [<ffff0000085850b0>] bus_add_driver+0x1f0/0x2a8
  [<ffff000008586ae0>] driver_register+0x60/0xf8
  [<ffff00000842f9b4>] __pci_register_driver+0x3c/0x48
  [<ffff000000a3001c>] ahci_pci_driver_init+0x1c/0x1000 [ahci]
  [<ffff000008083918>] do_one_initcall+0x38/0x120

where an obvious hardware level failure results in an unnecessary 15 second
delay and a subsequent crash.

So record the result code of ahci_reset_controller() and relay it, rather
than ignoring it.

Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>

Linux 4.14-rc3

Merge branch 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/tip

Pull x86 fixes from Thomas Gleixner:
"This contains the following fixes and improvements:

   - Avoid dereferencing an unprotected VMA pointer in the fault signal
     generation code

   - Fix inline asm call constraints for GCC 4.4

   - Use existing register variable to retrieve the stack pointer
     instead of forcing the compiler to create another indirect access
     which results in excessive extra 'mov %rsp, %<dst>' instructions

   - Disable branch profiling for the memory encryption code to prevent
     an early boot crash

   - Fix a sparse warning caused by casting the __user annotation in
     __get_user_asm_u64() away

   - Fix an off by one error in the loop termination of the error patch
     in the x86 sysfs init code

   - Add missing CPU IDs to various Intel specific drivers to enable the
     functionality on recent hardware

   - More (init) constification in the numachip code"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/asm: Use register variable to get stack pointer value
  x86/mm: Disable branch profiling in mem_encrypt.c
  x86/asm: Fix inline asm call constraints for GCC 4.4
  perf/x86/intel/uncore: Correct num_boxes for IIO and IRP
  perf/x86/intel/rapl: Add missing CPU IDs
  perf/x86/msr: Add missing CPU IDs
  perf/x86/intel/cstate: Add missing CPU IDs
  x86: Don't cast away the __user in __get_user_asm_u64()
  x86/sysfs: Fix off-by-one error in loop termination
  x86/mm: Fix fault error path using unsafe vma pointer
  x86/numachip: Add const and __initconst to numachip2_clockevent

Merge branch 'timers-urgent-for-linus' of git://git./linux/kernel/git/tip/tip

Pull timer fixes from Thomas Gleixner:
"This adds a new timer wheel function which is required for the
  conversion of the timer callback function from the 'unsigned long
  data' argument to 'struct timer_list *timer'. This conversion has two
  benefits:

   1) It makes struct timer_list smaller

   2) Many callers hand in a pointer to the timer or to the structure
      containing the timer, which happens via type casting both at setup
      and in the callback. This change gets rid of the typecasts.

  Once the conversion is complete, which is planned for 4.15, the old
  setup function and the intermediate typecast in the new setup function
  go away along with the data field in struct timer_list.

  Merging this now into mainline allows a smooth queueing of the actual
  conversion in the affected maintainer trees without creating
  dependencies"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  um/time: Fixup namespace collision
  timer: Prepare to change timer callback argument type

Merge branch 'smp-urgent-for-linus' of git://git./linux/kernel/git/tip/tip

Pull smp/hotplug fixes from Thomas Gleixner:
"This addresses the fallout of the new lockdep mechanism which covers
  completions in the CPU hotplug code.

  The lockdep splats are false positives, but there is no way to
  annotate that reliably. The solution is to split the completions for
  CPU up and down, which requires some reshuffling of the failure
  rollback handling as well"

* 'smp-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  smp/hotplug: Hotplug state fail injection
  smp/hotplug: Differentiate the AP completion between up and down
  smp/hotplug: Differentiate the AP-work lockdep class between up and down
  smp/hotplug: Callback vs state-machine consistency
  smp/hotplug: Rewrite AP state machine core
  smp/hotplug: Allow external multi-instance rollback
  smp/hotplug: Add state diagram

Merge branch 'sched-urgent-for-linus' of git://git./linux/kernel/git/tip/tip

Pull scheduler fixes from Thomas Gleixner:
"The scheduler pull request comes with the following updates:

   - Prevent a divide by zero issue by validating the input value of
     sysctl_sched_time_avg

   - Make task state printing consistent all over the place and have
     explicit state characters for IDLE and PARKED so they wont be
     displayed as 'D' state which confuses tools"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/sysctl: Check user input value of sysctl_sched_time_avg
  sched/debug: Add explicit TASK_PARKED printing
  sched/debug: Ignore TASK_IDLE for SysRq-W
  sched/debug: Add explicit TASK_IDLE printing
  sched/tracing: Use common task-state helpers
  sched/tracing: Fix trace_sched_switch task-state printing
  sched/debug: Remove unused variable
  sched/debug: Convert TASK_state to hex
  sched/debug: Implement consistent task-state printing

Merge branch 'perf-urgent-for-linus' of git://git./linux/kernel/git/tip/tip

Pull perf fixes from Thomas Gleixner:

- Prevent a division by zero in the perf aux buffer handling

- Sync kernel headers with perf tool headers

- Fix a build failure in the syscalltbl code

- Make the debug messages of perf report --call-graph work correctly

- Make sure that all required perf files are in the MANIFEST for
   container builds

- Fix the atrr.exclude kernel handling so it respects the
   perf_event_paranoid and the user permissions

- Make perf test on s390x work correctly

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/aux: Only update ->aux_wakeup in non-overwrite mode
  perf test: Fix vmlinux failure on s390x part 2
  perf test: Fix vmlinux failure on s390x
  perf tools: Fix syscalltbl build failure
  perf report: Fix debug messages with --call-graph option
  perf evsel: Fix attr.exclude_kernel setting for default cycles:p
  tools include: Sync kernel ABI headers with tooling headers
  perf tools: Get all of tools/{arch,include}/ in the MANIFEST

Merge branch 'locking-urgent-for-linus' of git://git./linux/kernel/git/tip/tip

Pull  locking fixes from Thomas Gleixner:
"Two fixes for locking:

   - Plug a hole the pi_stat->owner serialization which was changed
     recently and failed to fixup two usage sites.

   - Prevent reordering of the rwsem_has_spinner() check vs the
     decrement of rwsem count in up_write() which causes a missed
     wakeup"

* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  locking/rwsem-xadd: Fix missed wakeup due to reordering of load
  futex: Fix pi_state->owner serialization

Merge branch 'irq-urgent-for-linus' of git://git./linux/kernel/git/tip/tip

Pull irq fixes from Thomas Gleixner:

- Add a missing NULL pointer check in free_irq()

- Fix a memory leak/memory corruption in the generic irq chip

- Add missing rcu annotations for radix tree access

- Use ffs instead of fls when extracting data from a chip register in
   the MIPS GIC irq driver

- Fix the unmasking of IPI interrupts in the MIPS GIC driver so they
   end up at the target CPU and not at CPU0

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irq/generic-chip: Don't replace domain's name
  irqdomain: Add __rcu annotations to radix tree accessors
  irqchip/mips-gic: Use effective affinity to unmask
  irqchip/mips-gic: Fix shifts to extract register fields
  genirq: Check __free_irq() return value for NULL

Merge branch 'core-urgent-for-linus' of git://git./linux/kernel/git/tip/tip

Pull objtool fixes from Thomas Gleixner:
"Two small fixes for objtool:

   - Support frame pointer setup via 'lea (%rsp), %rbp' which was not
     yet supported and caused build warnings

   - Disable unreacahble warnings for GCC4.4 and older to avoid false
     positives caused by the compiler itself"

* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  objtool: Support unoptimized frame pointer setup
  objtool: Skip unreachable warnings for GCC 4.4 and older

Merge tag 'mtd/fixes-for-4.14-rc3' of git://git.infradead.org/linux-mtd

Pull mtd fixes from Boris Brezillon:

- Fix partition alignment check in mtdcore.c

- Fix a buffer overflow in the Atmel NAND driver

* tag 'mtd/fixes-for-4.14-rc3' of git://git.infradead.org/linux-mtd:
mtd: nand: atmel: fix buffer overflow in atmel_pmecc_user
mtd: Fix partition alignment check on multi-erasesize devices

Merge tag 'scsi-fixes' of git://git./linux/kernel/git/jejb/scsi

Pull SCSI fixes from James Bottomley:
"Eight mostly minor fixes for recently discovered issues in drivers"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: ILLEGAL REQUEST + ASC==27 => target failure
  scsi: aacraid: Add a small delay after IOP reset
  scsi: scsi_transport_fc: Also check for NOTPRESENT in fc_remote_port_add()
  scsi: scsi_transport_fc: set scsi_target_id upon rescan
  scsi: scsi_transport_iscsi: fix the issue that iscsi_if_rx doesn't parse nlmsg properly
  scsi: aacraid: error: testing array offset 'bus' after use
  scsi: lpfc: Don't return internal MBXERR_ERROR code from probe function
  scsi: aacraid: Fix 2T+ drives on SmartIOC-2000

Merge tag 'platform-drivers-x86-v4.14-2' of git://git.infradead.org/linux-platform-drivers-x86

Pull x86 platform drivers fix from Darren Hart:
"Newly discovered species of fujitsu laptops break some assumptions
  about ACPI device pairings.

  fujitsu-laptop: Don't oops when FUJ02E3 is not present"

* tag 'platform-drivers-x86-v4.14-2' of git://git.infradead.org/linux-platform-drivers-x86:
  platform/x86: fujitsu-laptop: Don't oops when FUJ02E3 is not presnt

Merge tag 'led_fixes-4.14-rc3' of git://git./linux/kernel/git/j.anaszewski/linux-leds

Pull LED fixes from Jacek Anaszewski:
"Four fixes for the as3645a LED flash controller and one update to
  MAINTAINERS"

* tag 'led_fixes-4.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
  MAINTAINERS: Add entry for MediaTek PMIC LED driver
  as3645a: Unregister indicator LED on device unbind
  as3645a: Use integer numbers for parsing LEDs
  dt: bindings: as3645a: Use LED number to refer to LEDs
  as3645a: Use ams,input-max-microamp as documented in DT bindings

Merge branch 'for-linus' of git://git./linux/kernel/git/viro/vfs

Pull waitid fix from Al Viro:
"Fix infoleak in waitid()"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fix infoleak in waitid(2)

Merge branch 'for-4.14-rc3' of git://git./linux/kernel/git/kdave/linux

Pull btrfs fixes from David Sterba:
"We've collected a bunch of isolated fixes, for crashes, user-visible
  behaviour or missing bits from other subsystem cleanups from the past.

  The overall number is not small but I was not able to make it
  significantly smaller. Most of the patches are supposed to go to
  stable"

* 'for-4.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  btrfs: log csums for all modified extents
  Btrfs: fix unexpected result when dio reading corrupted blocks
  btrfs: Report error on removing qgroup if del_qgroup_item fails
  Btrfs: skip checksum when reading compressed data if some IO have failed
  Btrfs: fix kernel oops while reading compressed data
  Btrfs: use btrfs_op instead of bio_op in __btrfs_map_block
  Btrfs: do not backup tree roots when fsync
  btrfs: remove BTRFS_FS_QUOTA_DISABLING flag
  btrfs: propagate error to btrfs_cmp_data_prepare caller
  btrfs: prevent to set invalid default subvolid
  Btrfs: send: fix error number for unknown inode types
  btrfs: fix NULL pointer dereference from free_reloc_roots()
  btrfs: finish ordered extent cleaning if no progress is found
  btrfs: clear ordered flag on cleaning up ordered extents
  Btrfs: fix incorrect {node,sector}size endianness from BTRFS_IOC_FS_INFO
  Btrfs: do not reset bio->bi_ops while writing bio
  Btrfs: use the new helper wbc_to_write_flags

Merge tag 'md/4.14-rc3' of git://git./linux/kernel/git/shli/md

Pull MD fixes from Shaohua Li:
"A few fixes for MD. Mainly fix a problem introduced in 4.13, which we
  retry bio for some code paths but not all in some situations"

* tag 'md/4.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md:
  md/raid5: cap worker count
  dm-raid: fix a race condition in request handling
  md: fix a race condition for flush request handling
  md: separate request handling

Merge tag 'pci-v4.14-fixes-3' of git://git./linux/kernel/git/helgaas/pci

Pull PCI fixes from Bjorn Helgaas:

- fix CONFIG_PCI=n build error (introduced in v4.14-rc1) (Geert
   Uytterhoeven)

- fix a race in sysfs driver_override store/show (Nicolai Stange)

* tag 'pci-v4.14-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  PCI: Fix race condition with driver_override
  PCI: Add dummy pci_acs_enabled() for CONFIG_PCI=n build

Merge tag 'drm-fixes-for-v4.14-rc3' of git://people.freedesktop.org/~airlied/linux

Pull drm fixes from Dave Airlie:
"Regular fixes pull, some amdkfd, amdgpu, etnaviv, sun4i, qxl, tegra
  fixes.

  I've got an outstanding pull for i915 but it wasn't on an rc2 base so
  I wanted to ship these out first, I might get to it before rc3 or I
  might not"

* tag 'drm-fixes-for-v4.14-rc3' of git://people.freedesktop.org/~airlied/linux:
  drm/tegra: trace: Fix path to include
  qxl: fix framebuffer unpinning
  drm/sun4i: cec: Enable back CEC-pin framework
  drm/amdkfd: Print event limit messages only once per process
  drm/amdkfd: Fix kernel-queue wrapping bugs
  drm/amdkfd: Fix incorrect destroy_mqd parameter
  drm/radeon: disable hard reset in hibernate for APUs
  drm/amdgpu: revert tile table update for oland
  etnaviv: fix gem object list corruption
  etnaviv: fix submit error path
  qxl: fix primary surface handling
  drm/amdkfd: check for null dev to avoid a null pointer dereference

Merge tag 'iommu-fixes-v4.14-rc2' of git://git./linux/kernel/git/joro/iommu

Pull IOMMU fixes from Joerg Roedel:

- A comment fix for 'struct iommu_ops'

- Format string fixes for AMD IOMMU, unfortunatly I missed that during
   review.

- Limit mediatek physical addresses to 32 bit for v7s to fix a warning
   triggered in io-page-table code.

- Fix dma-sync in io-pgtable-arm-v7s code

* tag 'iommu-fixes-v4.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
  iommu: Fix comment for iommu_ops.map_sg
  iommu/amd: pr_err() strings should end with newlines
  iommu/mediatek: Limit the physical address in 32bit for v7s
  iommu/io-pgtable-arm-v7s: Need dma-sync while there is no QUIRK_NO_DMA

Merge tag 'arm64-fixes' of git://git./linux/kernel/git/arm64/linux

Pull arm64 fixes from Catalin Marinas:

- SPsel register initialisation on reset as the architecture defines
   its state as unknown

- Use READ_ONCE when dereferencing pmd_t pointers to avoid race
   conditions in page_vma_mapped_walk() (or fast GUP) with concurrent
   modifications of the page table

- Avoid invoking the mm fault handling code for kernel addresses (check
   against TASK_SIZE) which would otherwise result in calling
   might_sleep() in atomic context

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: fault: Route pte translation faults via do_translation_fault
  arm64: mm: Use READ_ONCE when dereferencing pointer to pte table
  arm64: Make sure SPsel is always set

Merge tag 'for-linus-4.14c-rc3-tag' of git://git./linux/kernel/git/xen/tip

Pull xen fixes from Juergen Gross:

- avoid a warning when compiling with clang

- consider read-only bits in xen-pciback when writing to a BAR

- fix a boot crash of pv-domains

* tag 'for-linus-4.14c-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  xen/mmu: Call xen_cleanhighmap() with 4MB aligned for page tables mapping
  xen-pciback: relax BAR sizing write value check
  x86/xen: clean up clang build warning

Merge tag 'for-linus' of git://git./virt/kvm/kvm

Pull kvm fixes from Paolo Bonzini:
"Mixed bugfixes. Perhaps the most interesting one is a latent bug that
  was finally triggered by PCID support"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  kvm/x86: Handle async PF in RCU read-side critical sections
  KVM: nVMX: Fix nested #PF intends to break L1's vmlauch/vmresume
  KVM: VMX: use cmpxchg64
  KVM: VMX: simplify and fix vmx_vcpu_pi_load
  KVM: VMX: avoid double list add with VT-d posted interrupts
  KVM: VMX: extract __pi_post_block
  KVM: PPC: Book3S HV: Check for updated HDSISR on P9 HDSI exception
  KVM: nVMX: fix HOST_CR3/HOST_CR4 cache

fix infoleak in waitid(2)

kernel_waitid() can return a PID, an error or 0. rusage is filled in the first
case and waitid(2) rusage should've been copied out exactly in that case, *not*
whenever kernel_waitid() has not returned an error. Compat variant shares that
braino; none of kernel_wait4() callers do, so the below ought to fix it.

Reported-and-tested-by: Alexander Potapenko <glider@google.com>
Fixes: ce72a16fa705 ("wait4(2)/waitid(2): separate copying rusage to userland")
Cc: stable@vger.kernel.org # v4.13
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

x86/asm: Use register variable to get stack pointer value

Currently we use current_stack_pointer() function to get the value
of the stack pointer register. Since commit:

  f5caf621ee35 ("x86/asm: Fix inline asm call constraints for Clang")

... we have a stack register variable declared. It can be used instead of
current_stack_pointer() function which allows to optimize away some
excessive "mov %rsp, %<dst>" instructions:

-mov    %rsp,%rdx
-sub    %rdx,%rax
-cmp    $0x3fff,%rax
-ja     ffffffff810722fd <ist_begin_non_atomic+0x2d>

+sub    %rsp,%rax
+cmp    $0x3fff,%rax
+ja     ffffffff810722fa <ist_begin_non_atomic+0x2a>

Remove current_stack_pointer(), rename __asm_call_sp to current_stack_pointer
and use it instead of the removed function.

Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20170929141537.29167-1-aryabinin@virtuozzo.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>

x86/mm: Disable branch profiling in mem_encrypt.c

Some routines in mem_encrypt.c are called very early in the boot process,
e.g. sme_encrypt_kernel(). When CONFIG_TRACE_BRANCH_PROFILING=y is defined
the resulting branch profiling associated with the check to see if SME is
active results in a kernel crash. Disable branch profiling for
mem_encrypt.c by defining DISABLE_BRANCH_PROFILING before including any
header files.

Reported-by: kernel test robot <lkp@01.org>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Acked-by: Borislav Petkov <bp@suse.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20170929162419.6016.53390.stgit@tlendack-t1.amdoffice.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>

Merge tag 'perf-urgent-for-mingo-4.14-20170928' of git://git./linux/kernel/git/acme/linux into perf/urgent

Pull perf/urgent fixes from Arnaldo Carvalho de Melo:

- Fix syscalltbl build failure (Akemi Yagi)

- Fix attr.exclude_kernel setting for default cycles:p, this time for
!root with kernel.perf_event_paranoid = -1 (Arnaldo Carvalho de Melo)

- Sync kernel ABI headers with tooling headers (Ingo Molnar)

- Remove misleading debug messages with --call-graph option (Mengting Zhang)

- Revert vmlinux symbol resolution patches for s390x (Thomas Richter)

Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>

Merge branch 'fixes-v4.14-rc3' of git://git./linux/kernel/git/jmorris/linux-security

Pull keys fixes from James Morris:
"Notable here is a rewrite of big_key crypto by Jason Donenfeld to
  address some issues in the original code.

  From Jason's commit log:
   "This started out as just replacing the use of crypto/rng with
    get_random_bytes_wait, so that we wouldn't use bad randomness at
    boot time. But, upon looking further, it appears that there were
    even deeper underlying cryptographic problems, and that this seems
    to have been committed with very little crypto review. So, I rewrote
    the whole thing, trying to keep to the conventions introduced by the
    previous author, to fix these cryptographic flaws."

  There has been positive review of the new code by Eric Biggers and
  Herbert Xu, and it passes basic testing via the keyutils test suite.
  Eric also manually tested it.

  Generally speaking, we likely need to improve the amount of crypto
  review for kernel crypto users including keys (I'll post a note
  separately to ksummit-discuss)"

* 'fixes-v4.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
  security/keys: rewrite all of big_key crypto
  security/keys: properly zero out sensitive key material in big_key
  KEYS: use kmemdup() in request_key_auth_new()
  KEYS: restrict /proc/keys by credentials at open time
  KEYS: reset parent each time before searching key_user_tree
  KEYS: prevent KEYCTL_READ on negative key
  KEYS: prevent creating a different user's keyrings
  KEYS: fix writing past end of user-supplied buffer in keyring_read()
  KEYS: fix key refcount leak in keyctl_read_key()
  KEYS: fix key refcount leak in keyctl_assume_authority()
  KEYS: don't revoke uninstantiated key in request_key_auth_new()
  KEYS: fix cred refcount leak in request_key_auth_new()

arm64: fault: Route pte translation faults via do_translation_fault

We currently route pte translation faults via do_page_fault, which elides
the address check against TASK_SIZE before invoking the mm fault handling
code. However, this can cause issues with the path walking code in
conjunction with our word-at-a-time implementation because
load_unaligned_zeropad can end up faulting in kernel space if it reads
across a page boundary and runs into a page fault (e.g. by attempting to
read from a guard region).

In the case of such a fault, load_unaligned_zeropad has registered a
fixup to shift the valid data and pad with zeroes, however the abort is
reported as a level 3 translation fault and we dispatch it straight to
do_page_fault, despite it being a kernel address. This results in calling
a sleeping function from atomic context:

  BUG: sleeping function called from invalid context at arch/arm64/mm/fault.c:313
  in_atomic(): 0, irqs_disabled(): 0, pid: 10290
  Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
  [...]
  [<ffffff8e016cd0cc>] ___might_sleep+0x134/0x144
  [<ffffff8e016cd158>] __might_sleep+0x7c/0x8c
  [<ffffff8e016977f0>] do_page_fault+0x140/0x330
  [<ffffff8e01681328>] do_mem_abort+0x54/0xb0
  Exception stack(0xfffffffb20247a70 to 0xfffffffb20247ba0)
  [...]
  [<ffffff8e016844fc>] el1_da+0x18/0x78
  [<ffffff8e017f399c>] path_parentat+0x44/0x88
  [<ffffff8e017f4c9c>] filename_parentat+0x5c/0xd8
  [<ffffff8e017f5044>] filename_create+0x4c/0x128
  [<ffffff8e017f59e4>] SyS_mkdirat+0x50/0xc8
  [<ffffff8e01684e30>] el0_svc_naked+0x24/0x28
  Code: 36380080 d5384100 f9400800 9402566d (d4210000)
  ---[ end trace 2d01889f2bca9b9f ]---

Fix this by dispatching all translation faults to do_translation_faults,
which avoids invoking the page fault logic for faults on kernel addresses.

Cc: <stable@vger.kernel.org>
Reported-by: Ankit Jain <ankijain@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

arm64: mm: Use READ_ONCE when dereferencing pointer to pte table

On kernels built with support for transparent huge pages, different CPUs
can access the PMD concurrently due to e.g. fast GUP or page_vma_mapped_walk
and they must take care to use READ_ONCE to avoid value tearing or caching
of stale values by the compiler. Unfortunately, these functions call into
our pgtable macros, which don't use READ_ONCE, and compiler caching has
been observed to cause the following crash during ext4 writeback:

PC is at check_pte+0x20/0x170
LR is at page_vma_mapped_walk+0x2e0/0x540
[...]
Process doio (pid: 2463, stack limit = 0xffff00000f2e8000)
Call trace:
[<ffff000008233328>] check_pte+0x20/0x170
[<ffff000008233758>] page_vma_mapped_walk+0x2e0/0x540
[<ffff000008234adc>] page_mkclean_one+0xac/0x278
[<ffff000008234d98>] rmap_walk_file+0xf0/0x238
[<ffff000008236e74>] rmap_walk+0x64/0xa0
[<ffff0000082370c8>] page_mkclean+0x90/0xa8
[<ffff0000081f3c64>] clear_page_dirty_for_io+0x84/0x2a8
[<ffff00000832f984>] mpage_submit_page+0x34/0x98
[<ffff00000832fb4c>] mpage_process_page_bufs+0x164/0x170
[<ffff00000832fc8c>] mpage_prepare_extent_to_map+0x134/0x2b8
[<ffff00000833530c>] ext4_writepages+0x484/0xe30
[<ffff0000081f6ab4>] do_writepages+0x44/0xe8
[<ffff0000081e5bd4>] __filemap_fdatawrite_range+0xbc/0x110
[<ffff0000081e5e68>] file_write_and_wait_range+0x48/0xd8
[<ffff000008324310>] ext4_sync_file+0x80/0x4b8
[<ffff0000082bd434>] vfs_fsync_range+0x64/0xc0
[<ffff0000082332b4>] SyS_msync+0x194/0x1e8

This is because page_vma_mapped_walk loads the PMD twice before calling
pte_offset_map: the first time without READ_ONCE (where it gets all zeroes
due to a concurrent pmdp_invalidate) and the second time with READ_ONCE
(where it sees a valid table pointer due to a concurrent pmd_populate).
However, the compiler inlines everything and caches the first value in
a register, which is subsequently used in pte_offset_phys which returns
a junk pointer that is later dereferenced when attempting to access the
relevant pte.

This patch fixes the issue by using READ_ONCE in pte_offset_phys to ensure
that a stale value is not used. Whilst this is a point fix for a known
failure (and simple to backport), a full fix moving all of our page table
accessors over to {READ,WRITE}_ONCE and consistently using READ_ONCE in
page_vma_mapped_walk is in the works for a future kernel release.

Cc: Jon Masters <jcm@redhat.com>
Cc: Timur Tabi <timur@codeaurora.org>
Cc: <stable@vger.kernel.org>
Fixes: f27176cfc363 ("mm: convert page_mkclean_one() to use page_vma_mapped_walk()")
Tested-by: Richard Ruigrok <rruigrok@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

kvm/x86: Handle async PF in RCU read-side critical sections

Sasha Levin reported a WARNING:

| WARNING: CPU: 0 PID: 6974 at kernel/rcu/tree_plugin.h:329
| rcu_preempt_note_context_switch kernel/rcu/tree_plugin.h:329 [inline]
| WARNING: CPU: 0 PID: 6974 at kernel/rcu/tree_plugin.h:329
| rcu_note_context_switch+0x16c/0x2210 kernel/rcu/tree.c:458
...
| CPU: 0 PID: 6974 Comm: syz-fuzzer Not tainted 4.13.0-next-20170908+ #246
| Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS
| 1.10.1-1ubuntu1 04/01/2014
| Call Trace:
...
| RIP: 0010:rcu_preempt_note_context_switch kernel/rcu/tree_plugin.h:329 [inline]
| RIP: 0010:rcu_note_context_switch+0x16c/0x2210 kernel/rcu/tree.c:458
| RSP: 0018:ffff88003b2debc8 EFLAGS: 00010002
| RAX: 0000000000000001 RBX: 1ffff1000765bd85 RCX: 0000000000000000
| RDX: 1ffff100075d7882 RSI: ffffffffb5c7da20 RDI: ffff88003aebc410
| RBP: ffff88003b2def30 R08: dffffc0000000000 R09: 0000000000000001
| R10: 0000000000000000 R11: 0000000000000000 R12: ffff88003b2def08
| R13: 0000000000000000 R14: ffff88003aebc040 R15: ffff88003aebc040
| __schedule+0x201/0x2240 kernel/sched/core.c:3292
| schedule+0x113/0x460 kernel/sched/core.c:3421
| kvm_async_pf_task_wait+0x43f/0x940 arch/x86/kernel/kvm.c:158
| do_async_page_fault+0x72/0x90 arch/x86/kernel/kvm.c:271
| async_page_fault+0x22/0x30 arch/x86/entry/entry_64.S:1069
| RIP: 0010:format_decode+0x240/0x830 lib/vsprintf.c:1996
| RSP: 0018:ffff88003b2df520 EFLAGS: 00010283
| RAX: 000000000000003f RBX: ffffffffb5d1e141 RCX: ffff88003b2df670
| RDX: 0000000000000001 RSI: dffffc0000000000 RDI: ffffffffb5d1e140
| RBP: ffff88003b2df560 R08: dffffc0000000000 R09: 0000000000000000
| R10: ffff88003b2df718 R11: 0000000000000000 R12: ffff88003b2df5d8
| R13: 0000000000000064 R14: ffffffffb5d1e140 R15: 0000000000000000
| vsnprintf+0x173/0x1700 lib/vsprintf.c:2136
| sprintf+0xbe/0xf0 lib/vsprintf.c:2386
| proc_self_get_link+0xfb/0x1c0 fs/proc/self.c:23
| get_link fs/namei.c:1047 [inline]
| link_path_walk+0x1041/0x1490 fs/namei.c:2127
...

This happened when the host hit a page fault, and delivered it as in an
async page fault, while the guest was in an RCU read-side critical
section. The guest then tries to reschedule in kvm_async_pf_task_wait(),
but rcu_preempt_note_context_switch() would treat the reschedule as a
sleep in RCU read-side critical section, which is not allowed (even in
preemptible RCU). Thus the WARN.

To cure this, make kvm_async_pf_task_wait() go to the halt path if the
PF happens in a RCU read-side critical section.

Reported-by: Sasha Levin <levinsasha928@gmail.com>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: stable@vger.kernel.org
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

KVM: nVMX: Fix nested #PF intends to break L1's vmlauch/vmresume

------------[ cut here ]------------
WARNING: CPU: 4 PID: 5280 at /home/kernel/linux/arch/x86/kvm//vmx.c:11394 nested_vmx_vmexit+0xc2b/0xd70 [kvm_intel]
CPU: 4 PID: 5280 Comm: qemu-system-x86 Tainted: G        W  OE   4.13.0+ #17
RIP: 0010:nested_vmx_vmexit+0xc2b/0xd70 [kvm_intel]
Call Trace:
  ? emulator_read_emulated+0x15/0x20 [kvm]
  ? segmented_read+0xae/0xf0 [kvm]
  vmx_inject_page_fault_nested+0x60/0x70 [kvm_intel]
  ? vmx_inject_page_fault_nested+0x60/0x70 [kvm_intel]
  x86_emulate_instruction+0x733/0x810 [kvm]
  vmx_handle_exit+0x2f4/0xda0 [kvm_intel]
  ? kvm_arch_vcpu_ioctl_run+0xd2f/0x1c60 [kvm]
  kvm_arch_vcpu_ioctl_run+0xdab/0x1c60 [kvm]
  ? kvm_arch_vcpu_load+0x62/0x230 [kvm]
  kvm_vcpu_ioctl+0x340/0x700 [kvm]
  ? kvm_vcpu_ioctl+0x340/0x700 [kvm]
  ? __fget+0xfc/0x210
  do_vfs_ioctl+0xa4/0x6a0
  ? __fget+0x11d/0x210
  SyS_ioctl+0x79/0x90
  entry_SYSCALL_64_fastpath+0x23/0xc2

A nested #PF is triggered during L0 emulating instruction for L2. However, it
doesn't consider we should not break L1's vmlauch/vmresme. This patch fixes
it by queuing the #PF exception instead ,requesting an immediate VM exit from
L2 and keeping the exception for L1 pending for a subsequent nested VM exit.

This should actually work all the time, making vmx_inject_page_fault_nested
totally unnecessary.  However, that's not working yet, so this patch can work
around the issue in the meanwhile.

Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

sched/sysctl: Check user input value of sysctl_sched_time_avg

System will hang if user set sysctl_sched_time_avg to 0:

  [root@XXX ~]# sysctl kernel.sched_time_avg_ms=0

  Stack traceback for pid 0
  0xffff883f6406c600 0 0 1 3 R 0xffff883f6406cf50 *swapper/3
  ffff883f7ccc3ae8 0000000000000018 ffffffff810c4dd0 0000000000000000
  0000000000017800 ffff883f7ccc3d78 0000000000000003 ffff883f7ccc3bf8
  ffffffff810c4fc9 ffff883f7ccc3c08 00000000810c5043 ffff883f7ccc3c08
  Call Trace:
  <IRQ> [<ffffffff810c4dd0>] ? update_group_capacity+0x110/0x200
  [<ffffffff810c4fc9>] ? update_sd_lb_stats+0x109/0x600
  [<ffffffff810c5507>] ? find_busiest_group+0x47/0x530
  [<ffffffff810c5b84>] ? load_balance+0x194/0x900
  [<ffffffff810ad5ca>] ? update_rq_clock.part.83+0x1a/0xe0
  [<ffffffff810c6d42>] ? rebalance_domains+0x152/0x290
  [<ffffffff810c6f5c>] ? run_rebalance_domains+0xdc/0x1d0
  [<ffffffff8108a75b>] ? __do_softirq+0xfb/0x320
  [<ffffffff8108ac85>] ? irq_exit+0x125/0x130
  [<ffffffff810b3a17>] ? scheduler_ipi+0x97/0x160
  [<ffffffff81052709>] ? smp_reschedule_interrupt+0x29/0x30
  [<ffffffff8173a1be>] ? reschedule_interrupt+0x6e/0x80
   <EOI> [<ffffffff815bc83c>] ? cpuidle_enter_state+0xcc/0x230
  [<ffffffff815bc80c>] ? cpuidle_enter_state+0x9c/0x230
  [<ffffffff815bc9d7>] ? cpuidle_enter+0x17/0x20
  [<ffffffff810cd6dc>] ? cpu_startup_entry+0x38c/0x420
  [<ffffffff81053373>] ? start_secondary+0x173/0x1e0

Because divide-by-zero error happens in function:

update_group_capacity()
  update_cpu_capacity()
    scale_rt_capacity()
     {
          ...
          total = sched_avg_period() + delta;
          used = div_u64(avg, total);
          ...
     }

To fix this issue, check user input value of sysctl_sched_time_avg, keep
it unchanged when hitting invalid input, and set the minimum limit of
sysctl_sched_time_avg to 1 ms.

Reported-by: James Puthukattukaran <james.puthukattukaran@oracle.com>
Signed-off-by: Ethan Zhao <ethan.zhao@oracle.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: efault@gmx.de
Cc: ethan.kernel@gmail.com
Cc: keescook@chromium.org
Cc: mcgrof@kernel.org
Cc: <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/1504504774-18253-1-git-send-email-ethan.zhao@oracle.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>

x86/asm: Fix inline asm call constraints for GCC 4.4

The kernel test bot (run by Xiaolong Ye) reported that the following commit:

  f5caf621ee35 ("x86/asm: Fix inline asm call constraints for Clang")

is causing double faults in a kernel compiled with GCC 4.4.

Linus subsequently diagnosed the crash pattern and the buggy commit and found that
the issue is with this code:

  register unsigned int __asm_call_sp asm("esp");
  #define ASM_CALL_CONSTRAINT "+r" (__asm_call_sp)

Even on a 64-bit kernel, it's using ESP instead of RSP.  That causes GCC
to produce the following bogus code:

  ffffffff8147461d:       89 e0                   mov    %esp,%eax
  ffffffff8147461f:       4c 89 f7                mov    %r14,%rdi
  ffffffff81474622:       4c 89 fe                mov    %r15,%rsi
  ffffffff81474625:       ba 20 00 00 00          mov    $0x20,%edx
  ffffffff8147462a:       89 c4                   mov    %eax,%esp
  ffffffff8147462c:       e8 bf 52 05 00          callq  ffffffff814c98f0 <copy_user_generic_unrolled>

Despite the absurdity of it backing up and restoring the stack pointer
for no reason, the bug is actually the fact that it's only backing up
and restoring the lower 32 bits of the stack pointer.  The upper 32 bits
are getting cleared out, corrupting the stack pointer.

So change the '__asm_call_sp' register variable to be associated with
the actual full-size stack pointer.

This also requires changing the __ASM_SEL() macro to be based on the
actual compiled arch size, rather than the CONFIG value, because
CONFIG_X86_64 compiles some files with '-m32' (e.g., realmode and vdso).
Otherwise Clang fails to build the kernel because it complains about the
use of a 64-bit register (RSP) in a 32-bit file.

Reported-and-Bisected-and-Tested-by: kernel test robot <xiaolong.ye@intel.com>
Diagnosed-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Dmitriy Vyukov <dvyukov@google.com>
Cc: LKP <lkp@01.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matthias Kaehlcke <mka@chromium.org>
Cc: Miguel Bernal Marin <miguel.bernal.marin@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: f5caf621ee35 ("x86/asm: Fix inline asm call constraints for Clang")
Link: http://lkml.kernel.org/r/20170928215826.6sdpmwtkiydiytim@treble
Signed-off-by: Ingo Molnar <mingo@kernel.org>

sched/debug: Add explicit TASK_PARKED printing

Currently TASK_PARKED is masqueraded as TASK_INTERRUPTIBLE, give it
its own print state because it will not in fact get woken by regular
wakeups and is a long-term state.

This requires moving TASK_PARKED into the TASK_REPORT mask, and since
that latter needs to be a contiguous bitmask, we need to shuffle the
bits around a bit.

Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>

sched/debug: Ignore TASK_IDLE for SysRq-W

Markus reported that tasks in TASK_IDLE state are reported by SysRq-W,
which results in undesirable clutter.

Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>

sched/debug: Add explicit TASK_IDLE printing

Markus reported that kthreads that idle using TASK_IDLE instead of
TASK_INTERRUPTIBLE are reported in as TASK_UNINTERRUPTIBLE and things
like htop mark those red.

This is undesirable, so add an explicit state for TASK_IDLE.

Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>

sched/tracing: Use common task-state helpers

Remove yet another task-state char instance.

Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>

Merge tag 'fixes-for-v4.14-rc3' of git://git./linux/kernel/git/balbi/usb into usb-linus

Felipe writes:

usb: fixes for v4.14-rc3

Alan Stern fixed 3 old bugs on dummy_hcd which were reported recently.

Yoshihiro Shimoda continues his work on the renensas_usb3 driver by
fixing several bugs all over the place. The most important of which is
a fix for 2-stage control transfers, previously renesas_usb3 would,
anyway, try to move a 0-length data stage, which is wrong.

Apart from these, there are two minor bug fixes (atmel udc and ffs)
and a new device ID for dwc3-of-simple.c

locking/rwsem-xadd: Fix missed wakeup due to reordering of load

If a spinner is present, there is a chance that the load of
rwsem_has_spinner() in rwsem_wake() can be reordered with
respect to decrement of rwsem count in __up_write() leading
to wakeup being missed:

spinning writer                  up_write caller
---------------                  -----------------------
[S] osq_unlock()                 [L] osq
  spin_lock(wait_lock)
  sem->count=0xFFFFFFFF00000001
            +0xFFFFFFFF00000000
  count=sem->count
  MB
                                   sem->count=0xFFFFFFFE00000001
                                             -0xFFFFFFFF00000001
                                   spin_trylock(wait_lock)
                                   return
rwsem_try_write_lock(count)
spin_unlock(wait_lock)
schedule()

Reordering of atomic_long_sub_return_release() in __up_write()
and rwsem_has_spinner() in rwsem_wake() can cause missing of
wakeup in up_write() context. In spinning writer, sem->count
and local variable count is 0XFFFFFFFE00000001. It would result
in rwsem_try_write_lock() failing to acquire rwsem and spinning
writer going to sleep in rwsem_down_write_failed().

The smp_rmb() will make sure that the spinner state is
consulted after sem->count is updated in up_write context.

Signed-off-by: Prateek Sood <prsood@codeaurora.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: dave@stgolabs.net
Cc: longman@redhat.com
Cc: parri.andrea@gmail.com
Cc: sramana@codeaurora.org
Link: http://lkml.kernel.org/r/1504794658-15397-1-git-send-email-prsood@codeaurora.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>

sched/tracing: Fix trace_sched_switch task-state printing

Convert trace_sched_switch to use the common task-state helpers and
fix the "X" and "Z" order, possibly they ended up in the wrong order
because TASK_REPORT has them in the wrong order too.

Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>

sched/debug: Remove unused variable

Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>

sched/debug: Convert TASK_state to hex

Bit patterns are easier in hex.

Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>

sched/debug: Implement consistent task-state printing

Currently get_task_state() and task_state_to_char() report different
states, create a number of common helpers and unify the reported state
space.

Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>

um/time: Fixup namespace collision

The new timer_setup() function for struct timer_list collides with a
private um function. Rename it.

Fixes: 686fef928bba ("timer: Prepare to change timer callback argument type")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Richard Weinberger <richard@nod.at>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: user-mode-linux-devel@lists.sourceforge.net
Cc: Kees Cook <keescook@chromium.org>

perf/aux: Only update ->aux_wakeup in non-overwrite mode

The following commit:

d9a50b0256 ("perf/aux: Ensure aux_wakeup represents most recent wakeup index")

changed the AUX wakeup position calculation to rounddown(), which causes
a division-by-zero in AUX overwrite mode (aka "snapshot mode").

The zero denominator results from the fact that perf record doesn't set
aux_watermark to anything, in which case the kernel will set it to half
the AUX buffer size, but only for non-overwrite mode. In the overwrite
mode aux_watermark stays zero.

The good news is that, AUX overwrite mode, wakeups don't happen and
related bookkeeping is not relevant, so we can simply forego the whole
wakeup updates.

Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: will.deacon@arm.com
Link: http://lkml.kernel.org/r/20170906160811.16510-1-alexander.shishkin@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>

Merge tag 'drm-misc-fixes-2017-09-28-1' of git://anongit.freedesktop.org/git/drm-misc into drm-fixes

Driver Changes:
- qxl: fix primary surface and fb unpinning (Gerd)
- sun41: fix CEC_PIN config gate now that media has been merged (Hans)
- tegra: fix TRACE_INCLUDE_PATH (Thierry)

Cc: Thierry Reding <treding@nvidia.com>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Cc: Gerd Hoffmann <kraxel@redhat.com>
* tag 'drm-misc-fixes-2017-09-28-1' of git://anongit.freedesktop.org/git/drm-misc:
  drm/tegra: trace: Fix path to include
  qxl: fix framebuffer unpinning
  drm/sun4i: cec: Enable back CEC-pin framework
  qxl: fix primary surface handling

Merge tag 'acpi-4.14-rc3' of git://git./linux/kernel/git/rafael/linux-pm

Pull ACPI fix from Rafael Wysocki:
"This fixes an APEI problem that may cause a reported error to be
missed due to a race condition"

* tag 'acpi-4.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / APEI: clear error status before acknowledging the error

Merge tag 'pm-4.14-rc3' of git://git./linux/kernel/git/rafael/linux-pm

Pull power management fixes from Rafael Wysocki:
"These fix a deadlock in the operating performance points (OPP)
  framework introduced during the 4.11 cycle, more issues with duplicate
  device objects for cpufreq-dt and cpufreq documentation.

  Specifics:

   - Fix a deadlock in the operating performance points (OPP) framework
     caused by a notifier callback taking a lock that's already held by
     its caller (Viresh Kumar).

   - Prevent the ti-cpufreq and cpufreq-dt-platdev drivers from
     attempting to register conflicting device objects which triggers a
     warning from sysfs (Suniel Mahesh).

   - Drop a stale reference to a piece of intel_pstate documentation
     that's not in the tree any more (Rafael Wysocki)"

* tag 'pm-4.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  cpufreq: docs: Drop intel-pstate.txt from index.txt
  cpufreq: dt: Fix sysfs duplicate filename creation for platform-device
  PM / OPP: Call notifier without holding opp_table->lock

Merge tag 'xfs-4.14-fixes-2' of git://git./fs/xfs/xfs-linux

Pull xfs fixes from Darrick Wong:

- fix various problems with the copy-on-write extent maps getting freed
   at the wrong time

- fix printk format specifier problems

- report zeroing operation outcomes instead of dropping them on the
   floor

- fix some crashes when dio operations partially fail

- fix a race condition between unwritten extent conversion & dio read

- fix some incorrect tests in the inode log item processing

- correct the delayed allocation space reservations on rmap filesystems

- fix some problems checking for dax support

* tag 'xfs-4.14-fixes-2' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
  xfs: revert "xfs: factor rmap btree size into the indlen calculations"
  xfs: Capture state of the right inode in xfs_iflush_done
  xfs: perag initialization should only touch m_ag_max_usable for AG 0
  xfs: update i_size after unwritten conversion in dio completion
  iomap_dio_rw: Allocate AIO completion queue before submitting dio
  xfs: validate bdev support for DAX inode flag
  xfs: remove redundant re-initialization of total_nr_pages
  xfs: Output warning message when discard option was enabled even though the device does not support discard
  xfs: report zeroed or not correctly in xfs_zero_range()
  xfs: kill meaningless variable 'zero'
  fs/xfs: Use %pS printk format for direct addresses
  xfs: evict CoW fork extents when performing finsert/fcollapse
  xfs: don't unconditionally clear the reflink flag on zero-block files

Revert "Bluetooth: Add option for disabling legacy ioctl interfaces"

This reverts commit dbbccdc4ced015cdd4051299bd87fbe0254ad351.

It turns out that the "legacy" users aren't so legacy at all, and that
turning off the legacy ioctl will break the current Qt bluetooth stack
for bluetooth LE devices that were released just a couple of months ago.

So it's simply not true that this was a legacy interface that hasn't
been needed and is only limited to old legacy BT devices.  Because I
actually read Kconfig help messages, and actively try to turn off
features that I don't need, I turned the option off.

Then I spent _way_ too much time debugging BLE issues until I realized
that it wasn't the Qt and subsurface development that had broken one of
my dive computer BLE downloads, but simply my broken kernel config.

Maybe in a decade it will be true that this is a legacy interface.  And
maybe with a better help-text and correct dependencies, this kind of
legacy removal might be acceptable.  But as things are right now both
the commit message and the Kconfig help text were misleading, and the
Kconfig option had the wrong dependenencies.

There's no reason to keep that broken Kconfig option in the tree.

Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge branch 'acpi-apei'

* acpi-apei:
ACPI / APEI: clear error status before acknowledging the error

Merge tag 'for-linus' of git://git./linux/kernel/git/dledford/rdma

Pull rdma fixes from Doug Ledford:
"Second -rc update for 4.14.

  Both Mellanox and Intel had a series of -rc fixes that landed this
  week. The Mellanox bunch is spread throughout the stack and not just
  in their driver, where as the Intel bunch was mostly in the hfi1
  driver. And, several of the fixes in the hfi1 driver were more than
  just simple 5 line fixes. As a result, the hfi1 driver fixes has a
  sizable LOC count.

  Everything else is as one would expect in an RC cycle in terms of LOC
  count. One item that might jump out and make you think "That's not an
  rc item" is the fix that corrects a typo. But, that change fixes a
  typo in a user visible API that was just added in this merge window,
  so if we fix it now, we can fix it. If we don't, the typo is in the
  API forever. Another that might not appear to be a fix at first glance
  is the Simplify mlx5_ib_cont_pages patch, but the simplification
  allows them to fix a bug in the existing function whenever the length
  of an SGE exceeded page size. We also had to revert one patch from the
  merge window that was wrong.

  Summary:

   - a few core fixes
   - a few ipoib fixes
   - a few mlx5 fixes
   - a 7-patch hfi1 related series"

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
  IB/hfi1: Unsuccessful PCIe caps tuning should not fail driver load
  IB/hfi1: On error, fix use after free during user context setup
  Revert "IB/ipoib: Update broadcast object if PKey value was changed in index 0"
  IB/hfi1: Return correct value in general interrupt handler
  IB/hfi1: Check eeprom config partition validity
  IB/hfi1: Only reset QSFP after link up and turn off AOC TX
  IB/hfi1: Turn off AOC TX after offline substates
  IB/mlx5: Fix NULL deference on mlx5_ib_update_xlt failure
  IB/mlx5: Simplify mlx5_ib_cont_pages
  IB/ipoib: Fix inconsistency with free_netdev and free_rdma_netdev
  IB/ipoib: Fix sysfs Pkey create<->remove possible deadlock
  IB: Correct MR length field to be 64-bit
  IB/core: Fix qp_sec use after free access
  IB/core: Fix typo in the name of the tag-matching cap struct

Merge branches 'pm-opp' and 'pm-cpufreq'

* pm-opp:
  PM / OPP: Call notifier without holding opp_table->lock

* pm-cpufreq:
  cpufreq: docs: Drop intel-pstate.txt from index.txt
  cpufreq: dt: Fix sysfs duplicate filename creation for platform-device

Merge tag 'seccomp-v4.14-rc3' of git://git./linux/kernel/git/kees/linux

Pull seccomp fix from Kees Cook:
"Fix refcounting bug in CRIU interface, noticed by Chris Salls (Oleg &
Tycho)"

* tag 'seccomp-v4.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
seccomp: fix the usage of get/put_seccomp_filter() in seccomp_get_filter()

perf test: Fix vmlinux failure on s390x part 2

On s390x perf test 1 failed. It turned out that commit cf6383f73cf2
("perf report: Fix kernel symbol adjustment for s390x") was incorrect.

The previous implementation in dso__load_sym() is also suitable for
s390x.

Therefore this patch undoes commit cf6383f73cf2

Signed-off-by: Thomas-Mich Richter <tmricht@linux.vnet.ibm.com>
Cc: Zvonko Kosic <zvonko.kosic@de.ibm.com>
Cc: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Fixes: cf6383f73cf2 ("perf report: Fix kernel symbol adjustment for s390x")
LPU-Reference: 20170915071404.58398-2-tmricht@linux.vnet.ibm.com
Link: http://lkml.kernel.org/n/tip-v101o8k25vuja2ogosgf15yy@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

perf test: Fix vmlinux failure on s390x

On s390x perf test 1 failed. It turned out that commit 4a084ecfc821
("perf report: Fix module symbol adjustment for s390x") was incorrect.
The previous implementation in dso__load_sym() is also suitable for
s390x.

Therefore this patch undoes commit 4a084ecfc821.

Signed-off-by: Thomas-Mich Richter <tmricht@linux.vnet.ibm.com>
Cc: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Cc: Zvonko Kosic <zvonko.kosic@de.ibm.com>
Fixes: 4a084ecfc821 ("perf report: Fix module symbol adjustment for s390x")
LPU-Reference: 20170915071404.58398-1-tmricht@linux.vnet.ibm.com
Link: http://lkml.kernel.org/n/tip-5ani7ly57zji7s0hmzkx416l@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

KVM: VMX: use cmpxchg64

This fixes a compilation failure on 32-bit systems.

Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

percpu: fix iteration to prevent skipping over block

The iterator functions pcpu_next_md_free_region and
pcpu_next_fit_region use the block offset to determine if they have
checked the area in the prior iteration. However, this causes an issue
when the block offset is greater than subsequent block contig hints. If
within the iterator it moves to check subsequent blocks, it may fail in
the second predicate due to the block offset not being cleared. Thus,
this causes the allocator to skip over blocks leading to false failures
when allocating from the reserved chunk. While this happens in the
general case as well, it will only fail if it cannot allocate a new
chunk.

This patch resets the block offset to 0 to pass the second predicate
when checking subseqent blocks within the iterator function.

Signed-off-by: Dennis Zhou <dennisszhou@gmail.com>
Reported-and-tested-by: Luis Henriques <lhenriques@suse.com>
Signed-off-by: Tejun Heo <tj@kernel.org>

timer: Prepare to change timer callback argument type

Modern kernel callback systems pass the structure associated with a
given callback to the callback function. The timer callback remains one
of the legacy cases where an arbitrary unsigned long argument continues
to be passed as the callback argument. This has several problems:

- This bloats the timer_list structure with a normally redundant
  .data field.

- No type checking is being performed, forcing callbacks to do
  explicit type casts of the unsigned long argument into the object
  that was passed, rather than using container_of(), as done in most
  of the other callback infrastructure.

- Neighboring buffer overflows can overwrite both the .function and
  the .data field, providing attackers with a way to elevate from a buffer
  overflow into a simplistic ROP-like mechanism that allows calling
  arbitrary functions with a controlled first argument.

- For future Control Flow Integrity work, this creates a unique function
  prototype for timer callbacks, instead of allowing them to continue to
  be clustered with other void functions that take a single unsigned long
  argument.

This adds a new timer initialization API, which will ultimately replace
the existing setup_timer(), setup_{deferrable,pinned,etc}_timer() family,
named timer_setup() (to mirror hrtimer_setup(), making instances of its
use much easier to grep for).

In order to support the migration of existing timers into the new
callback arguments, timer_setup() casts its arguments to the existing
legacy types, and explicitly passes the timer pointer as the legacy
data argument. Once all setup_*timer() callers have been replaced with
timer_setup(), the casts can be removed, and the data argument can be
dropped with the timer expiration code changed to just pass the timer
to the callback directly.

Since the regular pattern of using container_of() during local variable
declaration repeats the need for the variable type declaration
to be included, this adds a helper modeled after other from_*()
helpers that wrap container_of(), named from_timer(). This helper uses
typeof(*variable), removing the type redundancy and minimizing the need
for line wraps in forthcoming conversions from "unsigned data long" to
"struct timer_list *" in the timer callbacks:

-void callback(unsigned long data)
+void callback(struct timer_list *t)
{
-   struct some_data_structure *local = (struct some_data_structure *)data;
+   struct some_data_structure *local = from_timer(local, t, timer);

Finally, in order to support the handful of timer users that perform
open-coded assignments of the .function (and .data) fields, provide
cast macros (TIMER_FUNC_TYPE and TIMER_DATA_TYPE) that can be used
temporarily. Once conversion has been completed, these can be globally
trivially removed.

Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20170928133817.GA113410@beast

xen/mmu: Call xen_cleanhighmap() with 4MB aligned for page tables mapping

When bootup a PVM guest with large memory(Ex.240GB), XEN provided initial
mapping overlaps with kernel module virtual space. When mapping in this space
is cleared by xen_cleanhighmap(), in certain case there could be an 2MB mapping
left. This is due to XEN initialize 4MB aligned mapping but xen_cleanhighmap()
finish at 2MB boundary.

When module loading is just on top of the 2MB space, got below warning:

WARNING: at mm/vmalloc.c:106 vmap_pte_range+0x14e/0x190()
Call Trace:
[<ffffffff81117083>] warn_alloc_failed+0xf3/0x160
[<ffffffff81146022>] __vmalloc_area_node+0x182/0x1c0
[<ffffffff810ac91e>] ? module_alloc_update_bounds+0x1e/0x80
[<ffffffff81145df7>] __vmalloc_node_range+0xa7/0x110
[<ffffffff810ac91e>] ? module_alloc_update_bounds+0x1e/0x80
[<ffffffff8103ca54>] module_alloc+0x64/0x70
[<ffffffff810ac91e>] ? module_alloc_update_bounds+0x1e/0x80
[<ffffffff810ac91e>] module_alloc_update_bounds+0x1e/0x80
[<ffffffff810ac9a7>] move_module+0x27/0x150
[<ffffffff810aefa0>] layout_and_allocate+0x120/0x1b0
[<ffffffff810af0a8>] load_module+0x78/0x640
[<ffffffff811ff90b>] ? security_file_permission+0x8b/0x90
[<ffffffff810af6d2>] sys_init_module+0x62/0x1e0
[<ffffffff815154c2>] system_call_fastpath+0x16/0x1b

Then the mapping of 2MB is cleared, finally oops when the page in that space is
accessed.

BUG: unable to handle kernel paging request at ffff880022600000
IP: [<ffffffff81260877>] clear_page_c_e+0x7/0x10
PGD 1788067 PUD 178c067 PMD 22434067 PTE 0
Oops: 0002 [#1] SMP
Call Trace:
[<ffffffff81116ef7>] ? prep_new_page+0x127/0x1c0
[<ffffffff81117d42>] get_page_from_freelist+0x1e2/0x550
[<ffffffff81133010>] ? ii_iovec_copy_to_user+0x90/0x140
[<ffffffff81119c9d>] __alloc_pages_nodemask+0x12d/0x230
[<ffffffff81155516>] alloc_pages_vma+0xc6/0x1a0
[<ffffffff81006ffd>] ? pte_mfn_to_pfn+0x7d/0x100
[<ffffffff81134cfb>] do_anonymous_page+0x16b/0x350
[<ffffffff81139c34>] handle_pte_fault+0x1e4/0x200
[<ffffffff8100712e>] ? xen_pmd_val+0xe/0x10
[<ffffffff810052c9>] ? __raw_callee_save_xen_pmd_val+0x11/0x1e
[<ffffffff81139dab>] handle_mm_fault+0x15b/0x270
[<ffffffff81510c10>] do_page_fault+0x140/0x470
[<ffffffff8150d7d5>] page_fault+0x25/0x30

Call xen_cleanhighmap() with 4MB aligned for page tables mapping to fix it.
The unnecessory call of xen_cleanhighmap() in DEBUG mode is also removed.

-v2: add comment about XEN alignment from Juergen.

References: https://lists.xen.org/archives/html/xen-devel/2012-07/msg01562.html
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@oracle.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
[boris: added 'xen/mmu' tag to commit subject]
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>

xen-pciback: relax BAR sizing write value check

Just like done in d2bd05d88d ("xen-pciback: return proper values during
BAR sizing") for the ROM BAR, ordinary ones also shouldn't compare the
written value directly against ~0, but consider the r/o bits at the
bottom (if any).

Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>

irq/generic-chip: Don't replace domain's name

When generic irq chips are allocated for an irq domain the domain name is
set to the irq chip name. That was done to have named domains before the
recent changes which enforce domain naming were done.

Since then the overwrite causes a memory leak when the domain name is
dynamically allocated and even worse it would cause the domain free code to
free the wrong name pointer, which might point to a constant.

Remove the name assignment to prevent this.

Fixes: d59f6617eef0 ("genirq: Allow fwnode to carry name information only")
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20170928043731.4764-1-jeffy.chen@rock-chips.com

usb: dwc3: of-simple: Add compatible for Spreadtrum SC9860 platform

Add compatible string to use this generic glue layer to support
Spreadtrum SC9860 platform's dwc3 controller.

Signed-off-by: Baolin Wang <baolin.wang@spreadtrum.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

usb: gadget: udc: atmel: set vbus irqflags explicitly

The driver triggers actions on both edges of the vbus signal.

The former PIO controller was triggering IRQs on both falling and rising edges
by default. Newer PIO controller don't, so it's better to set it explicitly to
IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING.

Without this patch we may trigger the connection with host but only on some
bouncing signal conditions and thus lose connecting events.

Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: stable <stable@vger.kernel.org> # v4.4+
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

usb: gadget: ffs: handle I/O completion in-order

By submitting completed transfers to the system workqueue there is no
guarantee that completion events will be queued up in the correct order,
as in multi-processor systems there is a thread running for each
processor and the work items are not bound to a particular core.

This means that several completions are in the queue at the same time,
they may be processed in parallel and complete out of order, resulting
in data appearing corrupt when read by userspace.

Create a single-threaded workqueue for FunctionFS so that data completed
requests is passed to userspace in the order in which they complete.

Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

usb: renesas_usbhs: fix usbhsf_fifo_clear() for RX direction

This patch fixes an issue that the usbhsf_fifo_clear() is possible
to cause 10 msec delay if the pipe is RX direction and empty because
the FRDY bit will never be set to 1 in such case.

Fixes: e8d548d54968 ("usb: renesas_usbhs: fifo became independent from pipe.")
Cc: <stable@vger.kernel.org> # v3.1+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

usb: renesas_usbhs: fix the BCLR setting condition for non-DCP pipe

This patch fixes an issue that the driver sets the BCLR bit of
{C,Dn}FIFOCTR register to 1 even when it's non-DCP pipe and
the FRDY bit of {C,Dn}FIFOCTR register is set to 1.

Fixes: e8d548d54968 ("usb: renesas_usbhs: fifo became independent from pipe.")
Cc: <stable@vger.kernel.org> # v3.1+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

usb: gadget: udc: renesas_usb3: Fix return value of usb3_write_pipe()

This patch fixes an issue that this driver cannot go status stage
in control read when the req.zero is set to 1 and the len in
usb3_write_pipe() is set to 0. Otherwise, if we use g_ncm driver,
usb enumeration takes long time (5 seconds or more).

Fixes: 746bfe63bba3 ("usb: gadget: renesas_usb3: add support for Renesas USB3.0 peripheral controller")
Cc: <stable@vger.kernel.org> # v4.5+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

usb: gadget: udc: renesas_usb3: fix Pn_RAMMAP.Pn_MPKT value

According to the datasheet of R-Car Gen3, the Pn_RAMMAP.Pn_MPKT should
be set to one of 8, 16, 32, 64, 512 and 1024. Otherwise, when a gadget
driver uses an interrupt endpoint, unexpected behavior happens. So,
this patch fixes it.

Fixes: 746bfe63bba3 ("usb: gadget: renesas_usb3: add support for Renesas USB3.0 peripheral controller")
Cc: <stable@vger.kernel.org> # v4.5+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

usb: gadget: udc: renesas_usb3: fix for no-data control transfer

When bRequestType & USB_DIR_IN is false and req.length is 0 in control
transfer, since it means non-data, this driver should not set the mode
as control write. So, this patch fixes it.

Fixes: 746bfe63bba3 ("usb: gadget: renesas_usb3: add support for Renesas USB3.0 peripheral controller")
Cc: <stable@vger.kernel.org> # v4.5+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

USB: dummy-hcd: Fix erroneous synchronization change

A recent change to the synchronization in dummy-hcd was incorrect.
The issue was that dummy_udc_stop() contained no locking and therefore
could race with various gadget driver callbacks, and the fix was to
add locking and issue the callbacks with the private spinlock held.

UDC drivers aren't supposed to do this.  Gadget driver callback
routines are allowed to invoke functions in the UDC driver, and these
functions will generally try to acquire the private spinlock.  This
would deadlock the driver.

The correct solution is to drop the spinlock before issuing callbacks,
and avoid races by emulating the synchronize_irq() call that all real
UDC drivers must perform in their ->udc_stop() routines after
disabling interrupts.  This involves adding a flag to dummy-hcd's
private structure to keep track of whether interrupts are supposed to
be enabled, and adding a counter to keep track of ongoing callbacks so
that dummy_udc_stop() can wait for them all to finish.

A real UDC driver won't receive disconnect, reset, suspend, resume, or
setup events once it has disabled interrupts.  dummy-hcd will receive
them but won't try to issue any gadget driver callbacks, which should
be just as good.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: f16443a034c7 ("USB: gadgetfs, dummy-hcd, net2280: fix locking for callbacks")
CC: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

USB: dummy-hcd: fix infinite-loop resubmission bug

The dummy-hcd HCD/UDC emulator tries not to do too much work during
each timer interrupt.  But it doesn't try very hard; currently all
it does is limit the total amount of bulk data transferred.  Other
transfer types aren't limited, and URBs that transfer no data (because
of an error, perhaps) don't count toward the limit, even though on a
real USB bus they would consume at least a minimum overhead.

This means it's possible to get the driver stuck in an infinite loop,
for example, if the host class driver resubmits an URB every time it
completes (which is common for interrupt URBs).  Each time the URB is
resubmitted it gets added to the end of the pending-URBs list, and
dummy-hcd doesn't stop until that list is empty.  Andrey Konovalov was
able to trigger this failure mode using the syzkaller fuzzer.

This patch fixes the infinite-loop problem by restricting the URBs
handled during each timer interrupt to those that were already on the
pending list when the interrupt routine started.  Newly added URBs
won't be processed until the next timer interrupt.  The problem of
properly accounting for non-bulk bandwidth (as well as packet and
transaction overhead) is not addressed here.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

USB: dummy-hcd: fix connection failures (wrong speed)

The dummy-hcd UDC driver is not careful about the way it handles
connection speeds. It ignores the module parameter that is supposed
to govern the maximum connection speed and it doesn't set the HCD
flags properly for the case where it ends up running at full speed.

The result is that in many cases, gadget enumeration over dummy-hcd
fails because the bMaxPacketSize byte in the device descriptor is set
incorrectly. For example, the default settings call for a high-speed
connection, but the maxpacket value for ep0 ends up being set for a
Super-Speed connection.

This patch fixes the problem by initializing the gadget's max_speed
and the HCD flags correctly.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

seccomp: fix the usage of get/put_seccomp_filter() in seccomp_get_filter()

As Chris explains, get_seccomp_filter() and put_seccomp_filter() can end
up using different filters. Once we drop ->siglock it is possible for
task->seccomp.filter to have been replaced by SECCOMP_FILTER_FLAG_TSYNC.

Fixes: f8e529ed941b ("seccomp, ptrace: add support for dumping seccomp filters")
Reported-by: Chris Salls <chrissalls5@gmail.com>
Cc: stable@vger.kernel.org # needs s/refcount_/atomic_/ for v4.12 and earlier
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
[tycho: add __get_seccomp_filter vs. open coding refcount_inc()]
Signed-off-by: Tycho Andersen <tycho@docker.com>
[kees: tweak commit log]
Signed-off-by: Kees Cook <keescook@chromium.org>

objtool: Support unoptimized frame pointer setup

Arnd Bergmann reported a bunch of warnings like:

  crypto/jitterentropy.o: warning: objtool: jent_fold_time()+0x3b: call without frame pointer save/setup
  crypto/jitterentropy.o: warning: objtool: jent_stuck()+0x1d: call without frame pointer save/setup
  crypto/jitterentropy.o: warning: objtool: jent_unbiased_bit()+0x15: call without frame pointer save/setup
  crypto/jitterentropy.o: warning: objtool: jent_read_entropy()+0x32: call without frame pointer save/setup
  crypto/jitterentropy.o: warning: objtool: jent_entropy_collector_free()+0x19: call without frame pointer save/setup

and

  arch/x86/events/core.o: warning: objtool: collect_events uses BP as a scratch register
  arch/x86/events/core.o: warning: objtool: events_ht_sysfs_show()+0x22: call without frame pointer save/setup

With certain rare configurations, GCC sometimes sets up the frame
pointer with:

  lea    (%rsp),%rbp

instead of:

  mov    %rsp,%rbp

The instructions are equivalent, so treat the former like the latter.

Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/a468af8b28a69b83fffc6d7668be9b6fcc873699.1506526584.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>

objtool: Skip unreachable warnings for GCC 4.4 and older

The kbuild bot occasionally reports warnings like:

  drivers/scsi/pcmcia/aha152x_core.o: warning: objtool: seldo_run()+0x130: unreachable instruction

These warnings are always with GCC 4.4.  That version of GCC sometimes
places unreachable instructions after calls to noreturn functions.

The unreachable warnings aren't very important anyway.  Just ignore them
for old versions of GCC.

Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/bc89b807d965b98ec18a0bb94f96a594bd58f2f2.1506551639.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>

md/raid5: cap worker count

static checker reports a potential integer overflow. Cap the worker count to
avoid the overflow.

Reported:-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Shaohua Li <shli@fb.com>

dm-raid: fix a race condition in request handling

raid_map calls pers->make_request, which missed the suspend check. Fix it with
the new md_handle_request API.

Fix: cc27b0c78c79(md: fix deadlock between mddev_suspend() and md_write_start())
Cc: Heinz Mauelshagen <heinzm@redhat.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>

md: fix a race condition for flush request handling

md_submit_flush_data calls pers->make_request, which missed the suspend check.
Fix it with the new md_handle_request API.

Reported-by: Nate Dailey <nate.dailey@stratus.com>
Tested-by: Nate Dailey <nate.dailey@stratus.com>
Fix: cc27b0c78c79(md: fix deadlock between mddev_suspend() and md_write_start())
Cc: stable@vger.kernel.org
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>

md: separate request handling

With commit cc27b0c78c79, pers->make_request could bail out without handling
the bio. If that happens, we should retry. The commit fixes md_make_request
but not other call sites. Separate the request handling part, so other call
sites can use it.

Reported-by: Nate Dailey <nate.dailey@stratus.com>
Fix: cc27b0c78c79(md: fix deadlock between mddev_suspend() and md_write_start())
Cc: stable@vger.kernel.org
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>