git.openwrt.org Git - openwrt/staging/blogic.git/log

dma-direct: don't truncate dma_required_mask to bus addressing capabilities

The dma required_mask needs to reflect the actual addressing capabilities
needed to handle the whole system RAM. When truncated down to the bus
addressing capabilities dma_addressing_limited() will incorrectly signal
no limitations for devices which are restricted by the bus_dma_mask.

Fixes: b4ebe6063204 (dma-direct: implement complete bus_dma_mask handling)
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

dma-direct: fix DMA_ATTR_NO_KERNEL_MAPPING

The new DMA_ATTR_NO_KERNEL_MAPPING needs to actually assign
a dma_addr to work. Also skip it if the architecture needs
forced decryption handling, as that needs a kernel virtual
address.

Fixes: d98849aff879 (dma-direct: handle DMA_ATTR_NO_KERNEL_MAPPING in common code)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>

Merge tag 'kbuild-fixes-v5.3-3' of git://git./linux/kernel/git/masahiroy/linux-kbuild

Pull Kbuild fixes from Masahiro Yamada:

- revive single target %.ko

- do not create built-in.a where it is unneeded

- do not create modules.order where it is unneeded

- show a warning if subdir-y/m is used to visit a module Makefile

* tag 'kbuild-fixes-v5.3-3' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  kbuild: show hint if subdir-y/m is used to visit module Makefile
  kbuild: generate modules.order only in directories visited by obj-y/m
  kbuild: fix false-positive need-builtin calculation
  kbuild: revive single target %.ko

Merge tag 'for-linus' of git://git./virt/kvm/kvm

Pull kvm fixes from Paolo Bonzini:
"Bugfixes (arm and x86) and cleanups"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  selftests: kvm: Adding config fragments
  KVM: selftests: Update gitignore file for latest changes
  kvm: remove unnecessary PageReserved check
  KVM: arm/arm64: vgic: Reevaluate level sensitive interrupts on enable
  KVM: arm: Don't write junk to CP15 registers on reset
  KVM: arm64: Don't write junk to sysregs on reset
  KVM: arm/arm64: Sync ICH_VMCR_EL2 back when about to block
  x86: kvm: remove useless calls to kvm_para_available
  KVM: no need to check return value of debugfs_create functions
  KVM: remove kvm_arch_has_vcpu_debugfs()
  KVM: Fix leak vCPU's VMCS value into other pCPU
  KVM: Check preempted_in_kernel for involuntary preemption
  KVM: LAPIC: Don't need to wakeup vCPU twice afer timer fire
  arm64: KVM: hyp: debug-sr: Mark expected switch fall-through
  KVM: arm64: Update kvm_arm_exception_class and esr_class_str for new EC
  KVM: arm: vgic-v3: Mark expected switch fall-through
  arm64: KVM: regmap: Fix unexpected switch fall-through
  KVM: arm/arm64: Introduce kvm_pmu_vcpu_init() to setup PMU counter index

Merge branch 'for-linus' of git://git./linux/kernel/git/dtor/input

Pull input updates from Dmitry Torokhov:

- newer systems with Elan touchpads will be switched over to SMBus

- HP Spectre X360 will be using SMbus/RMI4

- checks for invalid USB descriptors in kbtab and iforce

- build fixes for applespi driver (misconfigs)

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: iforce - add sanity checks
  Input: applespi - use struct_size() helper
  Input: kbtab - sanity check for endpoint type
  Input: usbtouchscreen - initialize PM mutex before using it
  Input: applespi - add dependency on LEDS_CLASS
  Input: synaptics - enable RMI mode for HP Spectre X360
  Input: elantech - annotate fall-through case in elantech_use_host_notify()
  Input: elantech - enable SMBus on new (2018+) systems
  Input: applespi - fix trivial typo in struct description
  Input: applespi - select CRC16 module
  Input: applespi - fix warnings detected by sparse

kbuild: show hint if subdir-y/m is used to visit module Makefile

Since commit ff9b45c55b26 ("kbuild: modpost: read modules.order instead
of $(MODVERDIR)/*.mod"), a module is no longer built in the following
pattern:

  [Makefile]
  subdir-y := some-module

  [some-module/Makefile]
  obj-m := some-module.o

You cannot write Makefile this way in upstream because modules.order is
not correctly generated. subdir-y is used to descend to a sub-directory
that builds tools, device trees, etc.

For external modules, the modules order does not matter. So, the
Makefile above was known to work.

I believe the Makefile should be re-written as follows:

  [Makefile]
  obj-m := some-module/

  [some-module/Makefile]
  obj-m := some-module.o

However, people will have no idea if their Makefile suddenly stops
working. In fact, I received questions from multiple people.

Show a warning for a while if obj-m is specified in a Makefile visited
by subdir-y or subdir-m.

I touched the %/ rule to avoid false-positive warnings for the single
target.

Cc: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Tom Stonecypher <thomas.edwardx.stonecypher@intel.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Jan Kiszka <jan.kiszka@siemens.com>

kbuild: generate modules.order only in directories visited by obj-y/m

The modules.order files in directories visited by the chain of obj-y
or obj-m are merged to the upper-level ones, and become parts of the
top-level modules.order. On the other hand, there is no need to
generate modules.order in directories visited by subdir-y or subdir-m
since they would become orphan anyway.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

kbuild: fix false-positive need-builtin calculation

The current implementation of need-builtin is false-positive,
for example, in the following Makefile:

obj-m := foo/
obj-y := foo/bar/

..., where foo/built-in.a is not required.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

kbuild: revive single target %.ko

I removed the single target %.ko in commit ff9b45c55b26 ("kbuild:
modpost: read modules.order instead of $(MODVERDIR)/*.mod") because
the modpost stage does not work reliably. For instance, the module
dependency, modversion, etc. do not work if we lack symbol information
from the other modules.

Yet, some people still want to build only one module in their interest,
and it may be still useful if it is used within those limitations.

Fixes: ff9b45c55b26 ("kbuild: modpost: read modules.order instead of $(MODVERDIR)/*.mod")
Reported-by: Don Brace <don.brace@microsemi.com>
Reported-by: Arend Van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Merge tag 'drm-fixes-2019-08-09' of git://anongit.freedesktop.org/drm/drm

Pull drm fixes from Dave Airlie:
"Usual fixes roundup. Nothing too crazy or serious, one non-released
  ioctl is removed in the amdkfd driver.

  core:
   - mode parser strncpy fix

  i915:
   - GLK DSI escape clock setting
   - HDCP memleak fix

  tegra:
   - one gpiod/of regression fix

  amdgpu:
   - fix VCN to handle the latest navi10 firmware
   - fix for fan control on navi10
   - properly handle SMU metrics table on navi10
   - fix a resume regression on Stoney
   - kfd revert a GWS ioctl

  vmwgfx:
   - memory leak fix

  rockchip:
   - suspend fix"

* tag 'drm-fixes-2019-08-09' of git://anongit.freedesktop.org/drm/drm:
  drm/vmwgfx: fix memory leak when too many retries have occurred
  Revert "drm/amdkfd: New IOCTL to allocate queue GWS"
  Revert "drm/amdgpu: fix transform feedback GDS hang on gfx10 (v2)"
  drm/amdgpu: pin the csb buffer on hw init for gfx v8
  drm/rockchip: Suspend DP late
  drm/i915: Fix wrong escape clock divisor init for GLK
  drm/i915: fix possible memory leak in intel_hdcp_auth_downstream()
  drm/modes: Fix unterminated strncpy
  drm/amd/powerplay: correct navi10 vcn powergate
  drm/amd/powerplay: honor hw limit on fetching metrics data for navi10
  drm/amd/powerplay: Allow changing of fan_control in smu_v11_0
  drm/amd/amdgpu/vcn_v2_0: Move VCN 2.0 specific dec ring test to vcn_v2_0
  drm/amd/amdgpu/vcn_v2_0: Mark RB commands as KMD commands
  drm/tegra: Fix gpiod_get_from_of_node() regression

Merge tag 'arm64-fixes' of git://git./linux/kernel/git/arm64/linux

Pull arm64 fix from Catalin Marinas:
"Fix bad_pte warning caused by pte_mkdevmap() not setting PTE_SPECIAL"

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: mm: add missing PTE_SPECIAL in pte_mkdevmap on arm64

Merge tag 's390-5.3-5' of git://git./linux/kernel/git/s390/linux

Pull s390 fixes from Vasily Gorbik:

- Map vdso also for statically linked binaries like all other
   architectures.

- Fix no .bss usage compile-time check to account common objects with
   the help of binutils size tool. Top level Makefile change acked-by
   Masahiro.

- A fix to make perf happy with _etext symbol type.

- Fix dump_pagetables which is broken since p*d_offset implementation
   change to comply with mm/gup.c expectations.

- Revert memory sharing for diag calls in protected virtualization,
   since this is not required after all.

- Couple of other minor code cleanups.

* tag 's390-5.3-5' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/vdso: map vdso also for statically linked binaries
  s390/build: use size command to perform empty .bss check
  kbuild: add OBJSIZE variable for the size tool
  s390: put _stext and _etext into .text section
  s390/head64: cleanup unused labels
  s390/unwind: remove stack recursion warning
  s390/setup: adjust start_code of init_mm to _text
  s390/mm: fix dump_pagetables top level page table walking
  s390/protvirt: avoid memory sharing for diag 308 set/store

Merge tag 'for-linus-20190809' of git://git.kernel.dk/linux-block

Pull block fixes from Jens Axboe:

- Revert of a bcache patch that caused an oops for some (Coly)

- ata rb532 unused warning fix (Gustavo)

- AoE kernel crash fix (He)

- Error handling fixup for blkdev_get() (Jan)

- libata read/write translation and SFF PIO fix (me)

- Use after free and error handling fix for O_DIRECT fragments. There's
   still a nowait + sync oddity in there, we'll nail that start next
   week. If all else fails, I'll queue a revert of the NOWAIT change.
   (me)

- Loop GFP_KERNEL -> GFP_NOIO deadlock fix (Mikulas)

- Two BFQ regression fixes that caused crashes (Paolo)

* tag 'for-linus-20190809' of git://git.kernel.dk/linux-block:
  bcache: Revert "bcache: use sysfs_match_string() instead of __sysfs_match_string()"
  loop: set PF_MEMALLOC_NOIO for the worker thread
  bdev: Fixup error handling in blkdev_get()
  block, bfq: handle NULL return value by bfq_init_rq()
  block, bfq: move update of waker and woken list to queue freeing
  block, bfq: reset last_completed_rq_bfqq if the pointed queue is freed
  block: aoe: Fix kernel crash due to atomic sleep when exiting
  libata: add SG safety checks in SFF pio transfers
  libata: have ata_scsi_rw_xlat() fail invalid passthrough requests
  block: fix O_DIRECT error handling for bio fragments
  ata: rb532_cf: Fix unused variable warning in rb532_pata_driver_probe

Merge tag 'mmc-v5.3-rc3' of git://git./linux/kernel/git/ulfh/mmc

Pull MMC fixes from Ulf Hansson:

- cavium: Fix DMA support

- sdhci-sprd: Fix soft reset when runtime resuming"

* tag 'mmc-v5.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
  mmc: cavium: Add the missing dma unmap when the dma has finished.
  mmc: cavium: Set the correct dma max segment size for mmc_host
  mmc: sdhci-sprd: Fix the incorrect soft reset operation when runtime resuming

Merge tag 'fbdev-v5.3-rc4' of git://github.com/bzolnier/linux

Pull fbdev fix from Bartlomiej Zolnierkiewicz:
"fbdev patches will now go to upstream through drm-misc tree for
  improved maintainership and better integration testing so update
  MAINTAINERS file accordingly"

* tag 'fbdev-v5.3-rc4' of git://github.com/bzolnier/linux:
  MAINTAINERS: handle fbdev changes through drm-misc tree

Merge tag 'pwm/for-5.3-rc4' of git://git./linux/kernel/git/thierry.reding/linux-pwm

Pull pwm fix from Thierry Reding:
"A single fix for a backlight brightness regression introduced in
this merge window"

* tag 'pwm/for-5.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
pwm: Fallback to the static lookup-list when acpi_pwm_get fails

Merge tag 'sound-5.3-rc4' of git://git./linux/kernel/git/tiwai/sound

Pull sound fixes from Takashi Iwai:
"Lots of small fixes at this time since we've received the ASoC fix
  batch now.

   - Some coverage in ASoC core mostly for minor issues like NULL checks
     for DPCM and proper error handling in DAI instantiation

   - A collection of small device-specific changes in various ASoC codec
     and platform drivers

   - OF-tree refcount fixes in a few ASoC drivers

   - Fixes of memory leaks in the error paths of various ASoC / ALSA
     drivers

   - A workaround for a long-standing issue on AMD HD-audio device

   - Updates of MAINTAINERS, mail addresses, file permission fixups"

* tag 'sound-5.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (38 commits)
  ALSA: firewire: fix a memory leak bug
  sound: fix a memory leak bug
  ALSA: hda - Workaround for crackled sound on AMD controller (1022:1457)
  ALSA: hiface: fix multiple memory leak bugs
  ALSA: hda - Don't override global PCM hw info flag
  ALSA: usb-audio: fix a memory leak bug
  ASoC: max98373: Remove executable bits
  ASoC: amd: acp3x: use dma address for acp3x dma driver
  ASoC: amd: acp3x: use dma_ops of parent device for acp3x dma driver
  ASoC: max98373: add 88200 and 96000 sampling rate support
  ASoC: sun4i-i2s: Incorrect SR and WSS computation
  MAINTAINERS: Update Intel ASoC drivers maintainers
  ASoC: ti: davinci-mcasp: Correct slot_width posed constraint
  ASoC: rockchip: Fix mono capture
  ASoC: Intel: Fix some acpi vs apci typo in somme comments
  ASoC: ti: davinci-mcasp: Fix clk PDIR handling for i2s master mode
  ASoC: Fail card instantiation if DAI format setup fails
  ASoC: SOF: Intel: hda: remove misleading error trace from IRQ thread
  ASoC: qcom: apq8016_sbc: Fix oops with multiple DAI links
  ASoC: dapm: fix a memory leak bug
  ...

Merge tag 'media/v5.3-3' of git://git./linux/kernel/git/mchehab/linux-media

Pull media fix from Mauro Carvalho Chehab:
"A fix at the vivid CEC support"

* tag 'media/v5.3-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
media: vivid: fix missing cec adapter name

Merge tag 'pm-5.3-rc4' of git://git./linux/kernel/git/rafael/linux-pm

Pull power management fix from Rafael Wysocki:
"Revert a recent PCI power management change that caused problems to
occur on multiple systems (Mika Westerberg)"

* tag 'pm-5.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Revert "PCI: Add missing link delays required by the PCIe spec"

Merge branch 'linus' of git://git./linux/kernel/git/herbert/crypto-2.6

Pull crypto fixes from Herbert Xu:
"Fix a number of bugs in the ccp driver"

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: ccp - Ignore tag length when decrypting GCM ciphertext
  crypto: ccp - Add support for valid authsize values less than 16
  crypto: ccp - Fix oops by properly managing allocated structures

Merge tag 'kvmarm-fixes-for-5.3-2' of git://git./linux/kernel/git/kvmarm/kvmarm into HEAD

KVM/arm fixes for 5.3, take #2

- Fix our system register reset so that we stop writing
  non-sensical values to them, and track which registers
  get reset instead.
- Sync VMCR back from the GIC on WFI so that KVM has an
  exact vue of PMR.
- Reevaluate state of HW-mapped, level triggered interrupts
  on enable.

Merge tag 'kvmarm-fixes-for-5.3' of git://git./linux/kernel/git/kvmarm/kvmarm into HEAD

KVM/arm fixes for 5.3

- A bunch of switch/case fall-through annotation, fixing one actual bug
- Fix PMU reset bug
- Add missing exception class debug strings

selftests: kvm: Adding config fragments

selftests kvm test cases need pre-required kernel configs for the test
to get pass.

Signed-off-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

KVM: selftests: Update gitignore file for latest changes

The kvm_create_max_vcpus test has been moved to the main directory,
and sync_regs_test is now available on s390x, too.

Signed-off-by: Thomas Huth <thuth@redhat.com>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

kvm: remove unnecessary PageReserved check

The same check is already done in kvm_is_reserved_pfn.

Reviewed-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

MAINTAINERS: handle fbdev changes through drm-misc tree

fbdev patches will now go to upstream through drm-misc tree (IOW
starting with v5.4 merge window fbdev changes will be included in
DRM pull request) for improved maintainership and better integration
testing. Update MAINTAINERS file accordingly.

Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>

bcache: Revert "bcache: use sysfs_match_string() instead of __sysfs_match_string()"

This reverts commit 89e0341af082dbc170019f908846f4a424efc86b.

In drivers/md/bcache/sysfs.c:bch_snprint_string_list(), NULL pointer at
the end of list is necessary. Remove the NULL from last element of each
lists will cause the following panic,

[ 4340.455652] bcache: register_cache() registered cache device nvme0n1
[ 4340.464603] bcache: register_bdev() registered backing device sdk
[ 4421.587335] bcache: bch_cached_dev_run() cached dev sdk is running already
[ 4421.587348] bcache: bch_cached_dev_attach() Caching sdk as bcache0 on set 354e1d46-d99f-4d8b-870b-078b80dc88a6
[ 5139.247950] general protection fault: 0000 [#1] SMP NOPTI
[ 5139.247970] CPU: 9 PID: 5896 Comm: cat Not tainted 4.12.14-95.29-default #1 SLE12-SP4
[ 5139.247988] Hardware name: HPE ProLiant DL380 Gen10/ProLiant DL380 Gen10, BIOS U30 04/18/2019
[ 5139.248006] task: ffff888fb25c0b00 task.stack: ffff9bbacc704000
[ 5139.248021] RIP: 0010:string+0x21/0x70
[ 5139.248030] RSP: 0018:ffff9bbacc707bf0 EFLAGS: 00010286
[ 5139.248043] RAX: ffffffffa7e432e3 RBX: ffff8881c20da02a RCX: ffff0a00ffffff04
[ 5139.248058] RDX: 3f00656863616362 RSI: ffff8881c20db000 RDI: ffffffffffffffff
[ 5139.248075] RBP: ffff8881c20db000 R08: 0000000000000000 R09: ffff8881c20da02a
[ 5139.248090] R10: 0000000000000004 R11: 0000000000000000 R12: ffff9bbacc707c48
[ 5139.248104] R13: 0000000000000fd6 R14: ffffffffc0665855 R15: ffffffffc0665855
[ 5139.248119] FS:  00007faf253b8700(0000) GS:ffff88903f840000(0000) knlGS:0000000000000000
[ 5139.248137] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 5139.248149] CR2: 00007faf25395008 CR3: 0000000f72150006 CR4: 00000000007606e0
[ 5139.248164] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 5139.248179] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 5139.248193] PKRU: 55555554
[ 5139.248200] Call Trace:
[ 5139.248210]  vsnprintf+0x1fb/0x510
[ 5139.248221]  snprintf+0x39/0x40
[ 5139.248238]  bch_snprint_string_list.constprop.15+0x5b/0x90 [bcache]
[ 5139.248256]  __bch_cached_dev_show+0x44d/0x5f0 [bcache]
[ 5139.248270]  ? __alloc_pages_nodemask+0xb2/0x210
[ 5139.248284]  bch_cached_dev_show+0x2c/0x50 [bcache]
[ 5139.248297]  sysfs_kf_seq_show+0xbb/0x190
[ 5139.248308]  seq_read+0xfc/0x3c0
[ 5139.248317]  __vfs_read+0x26/0x140
[ 5139.248327]  vfs_read+0x87/0x130
[ 5139.248336]  SyS_read+0x42/0x90
[ 5139.248346]  do_syscall_64+0x74/0x160
[ 5139.248358]  entry_SYSCALL_64_after_hwframe+0x3d/0xa2
[ 5139.248370] RIP: 0033:0x7faf24eea370
[ 5139.248379] RSP: 002b:00007fff82d03f38 EFLAGS: 00000246 ORIG_RAX: 0000000000000000
[ 5139.248395] RAX: ffffffffffffffda RBX: 0000000000020000 RCX: 00007faf24eea370
[ 5139.248411] RDX: 0000000000020000 RSI: 00007faf25396000 RDI: 0000000000000003
[ 5139.248426] RBP: 00007faf25396000 R08: 00000000ffffffff R09: 0000000000000000
[ 5139.248441] R10: 000000007c9d4d41 R11: 0000000000000246 R12: 00007faf25396000
[ 5139.248456] R13: 0000000000000003 R14: 0000000000000000 R15: 0000000000000fff
[ 5139.248892] Code: ff ff ff 0f 1f 80 00 00 00 00 49 89 f9 48 89 cf 48 c7 c0 e3 32 e4 a7 48 c1 ff 30 48 81 fa ff 0f 00 00 48 0f 46 d0 48 85 ff 74 45 <44> 0f b6 02 48 8d 42 01 45 84 c0 74 38 48 01 fa 4c 89 cf eb 0e

The simplest way to fix is to revert commit 89e0341af082 ("bcache: use
sysfs_match_string() instead of __sysfs_match_string()").

This bug was introduced in Linux v5.2, so this fix only applies to
Linux v5.2 is enough for stable tree maintainer.

Fixes: 89e0341af082 ("bcache: use sysfs_match_string() instead of __sysfs_match_string()")
Cc: stable@vger.kernel.org
Cc: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reported-by: Peifeng Lin <pflin@suse.com>
Acked-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

s390/vdso: map vdso also for statically linked binaries

s390 does not map the vdso for statically linked binaries, assuming
that this doesn't make sense. See commit fc5243d98ac2 ("[S390]
arch_setup_additional_pages arguments").

However with glibc commit d665367f596d ("linux: Enable vDSO for static
linking as default (BZ#19767)") and commit 5e855c895401 ("s390: Enable
VDSO for static linking") the vdso is also used for statically linked
binaries - if the kernel would make it available.

Therefore map the vdso always, just like all other architectures.

Reported-by: Stefan Liebler <stli@linux.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>

KVM: arm/arm64: vgic: Reevaluate level sensitive interrupts on enable

A HW mapped level sensitive interrupt asserted by a device will not be put
into the ap_list if it is disabled at the VGIC level. When it is enabled
again, it will be inserted into the ap_list and written to a list register
on guest entry regardless of the state of the device.

We could argue that this can also happen on real hardware, when the command
to enable the interrupt reached the GIC before the device had the chance to
de-assert the interrupt signal; however, we emulate the distributor and
redistributors in software and we can do better than that.

Signed-off-by: Alexandru Elisei <alexandru.elisei@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>

KVM: arm: Don't write junk to CP15 registers on reset

At the moment, the way we reset CP15 registers is mildly insane:
We write junk to them, call the reset functions, and then check that
we have something else in them.

The "fun" thing is that this can happen while the guest is running
(PSCI, for example). If anything in KVM has to evaluate the state
of a CP15 register while junk is in there, bad thing may happen.

Let's stop doing that. Instead, we track that we have called a
reset function for that register, and assume that the reset
function has done something.

In the end, the very need of this reset check is pretty dubious,
as it doesn't check everything (a lot of the CP15 reg leave outside
of the cp15_regs[] array). It may well be axed in the near future.

Signed-off-by: Marc Zyngier <maz@kernel.org>

KVM: arm64: Don't write junk to sysregs on reset

At the moment, the way we reset system registers is mildly insane:
We write junk to them, call the reset functions, and then check that
we have something else in them.

The "fun" thing is that this can happen while the guest is running
(PSCI, for example). If anything in KVM has to evaluate the state
of a system register while junk is in there, bad thing may happen.

Let's stop doing that. Instead, we track that we have called a
reset function for that register, and assume that the reset
function has done something. This requires fixing a couple of
sysreg refinition in the trap table.

In the end, the very need of this reset check is pretty dubious,
as it doesn't check everything (a lot of the sysregs leave outside of
the sys_regs[] array). It may well be axed in the near future.

Tested-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>

Merge tag 'drm-intel-fixes-2019-08-08' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes

drm/i915 fixes for v5.3-rc4:
- Fix GLK DSI escape clock setting
- Fix a memleak on HDCP revoked Ksv error path

Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/87pnlghz79.fsf@intel.com

Merge tag 'drm-misc-fixes-2019-08-08' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes

drm-misc-fixes for v5.3-rc4:
- Suspend fix for rockchip
- Fix unterminated strncpy cmdline mode parser

Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ace294a6-6bb2-d9b1-695d-3260e1d60831@linux.intel.com

Merge branch 'vmwgfx-fixes-5.3' of git://people.freedesktop.org/~thomash/linux into drm-fixes

One single memory leak fix.

Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thomas Hellstrom "VMware" <thomas@shipmail.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190808094615.31040-1-thomas@shipmail.org

Merge tag 'nfs-for-5.3-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs

Pull NFS client fixes from Trond Myklebust:
"Highlights include:

  Stable fixes:

   - NFSv4: Ensure we check the return value of update_open_stateid() so
     we correctly track active open state.

   - NFSv4: Fix for delegation state recovery to ensure we recover all
     open modes that are active.

   - NFSv4: Fix an Oops in nfs4_do_setattr

  Fixes:

   - NFS: Fix regression whereby fscache errors are appearing on 'nofsc'
     mounts

   - NFSv4: Fix a potential sleep while atomic in nfs4_do_reclaim()

   - NFSv4: Fix a credential refcount leak in nfs41_check_delegation_stateid

   - pNFS: Report errors from the call to nfs4_select_rw_stateid()

   - NFSv4: Various other delegation and open stateid recovery fixes

   - NFSv4: Fix state recovery behaviour when server connection times
     out"

* tag 'nfs-for-5.3-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
  NFSv4: Ensure state recovery handles ETIMEDOUT correctly
  NFS: Fix regression whereby fscache errors are appearing on 'nofsc' mounts
  NFSv4: Fix an Oops in nfs4_do_setattr
  NFSv4: Fix a potential sleep while atomic in nfs4_do_reclaim()
  NFSv4: Check the return value of update_open_stateid()
  NFSv4.1: Only reap expired delegations
  NFSv4.1: Fix open stateid recovery
  NFSv4: Report the error from nfs4_select_rw_stateid()
  NFSv4: When recovering state fails with EAGAIN, retry the same recovery
  NFSv4: Print an error in the syslog when state is marked as irrecoverable
  NFSv4: Fix delegation state recovery
  NFSv4: Fix a credential refcount leak in nfs41_check_delegation_stateid

arm64: mm: add missing PTE_SPECIAL in pte_mkdevmap on arm64

Without this patch, the MAP_SYNC test case will cause a print_bad_pte
warning on arm64 as follows:

[   25.542693] BUG: Bad page map in process mapdax333 pte:2e8000448800f53 pmd:41ff5f003
[   25.546360] page:ffff7e0010220000 refcount:1 mapcount:-1 mapping:ffff8003e29c7440 index:0x0
[   25.550281] ext4_dax_aops
[   25.550282] name:"__aaabbbcccddd__"
[   25.551553] flags: 0x3ffff0000001002(referenced|reserved)
[   25.555802] raw: 03ffff0000001002 ffff8003dfffa908 0000000000000000 ffff8003e29c7440
[   25.559446] raw: 0000000000000000 0000000000000000 00000001fffffffe 0000000000000000
[   25.563075] page dumped because: bad pte
[   25.564938] addr:0000ffffbe05b000 vm_flags:208000fb anon_vma:0000000000000000 mapping:ffff8003e29c7440 index:0
[   25.574272] file:__aaabbbcccddd__ fault:ext4_dax_fault mmmmap:ext4_file_mmap readpage:0x0
[   25.578799] CPU: 1 PID: 1180 Comm: mapdax333 Not tainted 5.2.0+ #21
[   25.581702] Hardware name: QEMU KVM Virtual Machine, BIOS 0.0.0 02/06/2015
[   25.585624] Call trace:
[   25.587008]  dump_backtrace+0x0/0x178
[   25.588799]  show_stack+0x24/0x30
[   25.590328]  dump_stack+0xa8/0xcc
[   25.591901]  print_bad_pte+0x18c/0x218
[   25.593628]  unmap_page_range+0x778/0xc00
[   25.595506]  unmap_single_vma+0x94/0xe8
[   25.597304]  unmap_vmas+0x90/0x108
[   25.598901]  unmap_region+0xc0/0x128
[   25.600566]  __do_munmap+0x284/0x3f0
[   25.602245]  __vm_munmap+0x78/0xe0
[   25.603820]  __arm64_sys_munmap+0x34/0x48
[   25.605709]  el0_svc_common.constprop.0+0x78/0x168
[   25.607956]  el0_svc_handler+0x34/0x90
[   25.609698]  el0_svc+0x8/0xc
[...]

The root cause is in _vm_normal_page, without the PTE_SPECIAL bit,
the return value will be incorrectly set to pfn_to_page(pfn) instead
of NULL. Besides, this patch also rewrite the pmd_mkdevmap to avoid
setting PTE_SPECIAL for pmd

The MAP_SYNC test case is as follows(Provided by Yibo Cai)
$#include <stdio.h>
$#include <string.h>
$#include <unistd.h>
$#include <sys/file.h>
$#include <sys/mman.h>

$#ifndef MAP_SYNC
$#define MAP_SYNC 0x80000
$#endif

/* mount -o dax /dev/pmem0 /mnt */
$#define F "/mnt/__aaabbbcccddd__"

int main(void)
{
    int fd;
    char buf[4096];
    void *addr;

    if ((fd = open(F, O_CREAT|O_TRUNC|O_RDWR, 0644)) < 0) {
        perror("open1");
        return 1;
    }

    if (write(fd, buf, 4096) != 4096) {
        perror("lseek");
        return 1;
    }

    addr = mmap(NULL, 4096, PROT_READ|PROT_WRITE, MAP_SHARED|MAP_SYNC, fd, 0);
    if (addr == MAP_FAILED) {
        perror("mmap");
        printf("did you mount with '-o dax'?\n");
        return 1;
    }

    memset(addr, 0x55, 4096);

    if (munmap(addr, 4096) == -1) {
        perror("munmap");
        return 1;
    }

    close(fd);

    return 0;
}

Fixes: 73b20c84d42d ("arm64: mm: implement pte_devmap support")
Reported-by: Yibo Cai <Yibo.Cai@arm.com>
Acked-by: Will Deacon <will@kernel.org>
Acked-by: Robin Murphy <Robin.Murphy@arm.com>
Signed-off-by: Jia He <justin.he@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

Merge tag '5.3-rc3-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6

Pull cifs fixes from Steve French:
"Six small SMB3 fixes, two for stable"

* tag '5.3-rc3-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
  SMB3: Kernel oops mounting a encryptData share with CONFIG_DEBUG_VIRTUAL
  smb3: update TODO list of missing features
  smb3: send CAP_DFS capability during session setup
  SMB3: Fix potential memory leak when processing compound chain
  SMB3: Fix deadlock in validate negotiate hits reconnect
  cifs: fix rmmod regression in cifs.ko caused by force_sig changes

loop: set PF_MEMALLOC_NOIO for the worker thread

A deadlock with this stacktrace was observed.

The loop thread does a GFP_KERNEL allocation, it calls into dm-bufio
shrinker and the shrinker depends on I/O completion in the dm-bufio
subsystem.

In order to fix the deadlock (and other similar ones), we set the flag
PF_MEMALLOC_NOIO at loop thread entry.

PID: 474    TASK: ffff8813e11f4600  CPU: 10  COMMAND: "kswapd0"
   #0 [ffff8813dedfb938] __schedule at ffffffff8173f405
   #1 [ffff8813dedfb990] schedule at ffffffff8173fa27
   #2 [ffff8813dedfb9b0] schedule_timeout at ffffffff81742fec
   #3 [ffff8813dedfba60] io_schedule_timeout at ffffffff8173f186
   #4 [ffff8813dedfbaa0] bit_wait_io at ffffffff8174034f
   #5 [ffff8813dedfbac0] __wait_on_bit at ffffffff8173fec8
   #6 [ffff8813dedfbb10] out_of_line_wait_on_bit at ffffffff8173ff81
   #7 [ffff8813dedfbb90] __make_buffer_clean at ffffffffa038736f [dm_bufio]
   #8 [ffff8813dedfbbb0] __try_evict_buffer at ffffffffa0387bb8 [dm_bufio]
   #9 [ffff8813dedfbbd0] dm_bufio_shrink_scan at ffffffffa0387cc3 [dm_bufio]
  #10 [ffff8813dedfbc40] shrink_slab at ffffffff811a87ce
  #11 [ffff8813dedfbd30] shrink_zone at ffffffff811ad778
  #12 [ffff8813dedfbdc0] kswapd at ffffffff811ae92f
  #13 [ffff8813dedfbec0] kthread at ffffffff810a8428
  #14 [ffff8813dedfbf50] ret_from_fork at ffffffff81745242

  PID: 14127  TASK: ffff881455749c00  CPU: 11  COMMAND: "loop1"
   #0 [ffff88272f5af228] __schedule at ffffffff8173f405
   #1 [ffff88272f5af280] schedule at ffffffff8173fa27
   #2 [ffff88272f5af2a0] schedule_preempt_disabled at ffffffff8173fd5e
   #3 [ffff88272f5af2b0] __mutex_lock_slowpath at ffffffff81741fb5
   #4 [ffff88272f5af330] mutex_lock at ffffffff81742133
   #5 [ffff88272f5af350] dm_bufio_shrink_count at ffffffffa03865f9 [dm_bufio]
   #6 [ffff88272f5af380] shrink_slab at ffffffff811a86bd
   #7 [ffff88272f5af470] shrink_zone at ffffffff811ad778
   #8 [ffff88272f5af500] do_try_to_free_pages at ffffffff811adb34
   #9 [ffff88272f5af590] try_to_free_pages at ffffffff811adef8
  #10 [ffff88272f5af610] __alloc_pages_nodemask at ffffffff811a09c3
  #11 [ffff88272f5af710] alloc_pages_current at ffffffff811e8b71
  #12 [ffff88272f5af760] new_slab at ffffffff811f4523
  #13 [ffff88272f5af7b0] __slab_alloc at ffffffff8173a1b5
  #14 [ffff88272f5af880] kmem_cache_alloc at ffffffff811f484b
  #15 [ffff88272f5af8d0] do_blockdev_direct_IO at ffffffff812535b3
  #16 [ffff88272f5afb00] __blockdev_direct_IO at ffffffff81255dc3
  #17 [ffff88272f5afb30] xfs_vm_direct_IO at ffffffffa01fe3fc [xfs]
  #18 [ffff88272f5afb90] generic_file_read_iter at ffffffff81198994
  #19 [ffff88272f5afc50] __dta_xfs_file_read_iter_2398 at ffffffffa020c970 [xfs]
  #20 [ffff88272f5afcc0] lo_rw_aio at ffffffffa0377042 [loop]
  #21 [ffff88272f5afd70] loop_queue_work at ffffffffa0377c3b [loop]
  #22 [ffff88272f5afe60] kthread_worker_fn at ffffffff810a8a0c
  #23 [ffff88272f5afec0] kthread at ffffffff810a8428
  #24 [ffff88272f5aff50] ret_from_fork at ffffffff81745242

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>

bdev: Fixup error handling in blkdev_get()

Commit 89e524c04fa9 ("loop: Fix mount(2) failure due to race with
LOOP_SET_FD") converted blkdev_get() to use the new helpers for
finishing claiming of a block device. However the conversion botched the
error handling in blkdev_get() and thus the bdev has been marked as held
even in case __blkdev_get() returned error. This led to occasional
warnings with block/001 test from blktests like:

kernel: WARNING: CPU: 5 PID: 907 at fs/block_dev.c:1899 __blkdev_put+0x396/0x3a0

Correct the error handling.

CC: stable@vger.kernel.org
Fixes: 89e524c04fa9 ("loop: Fix mount(2) failure due to race with LOOP_SET_FD")
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

block, bfq: handle NULL return value by bfq_init_rq()

As reported in [1], the call bfq_init_rq(rq) may return NULL in case
of OOM (in particular, if rq->elv.icq is NULL because memory
allocation failed in failed in ioc_create_icq()).

This commit handles this circumstance.

[1] https://lkml.org/lkml/2019/7/22/824

Cc: Hsin-Yi Wang <hsinyi@google.com>
Cc: Nicolas Boichat <drinkcat@chromium.org>
Cc: Doug Anderson <dianders@chromium.org>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Reported-by: Hsin-Yi Wang <hsinyi@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

block, bfq: move update of waker and woken list to queue freeing

Since commit 13a857a4c4e8 ("block, bfq: detect wakers and
unconditionally inject their I/O"), every bfq_queue has a pointer to a
waker bfq_queue and a list of the bfq_queues it may wake. In this
respect, when a bfq_queue, say Q, remains with no I/O source attached
to it, Q cannot be woken by any other bfq_queue, and cannot wake any
other bfq_queue. Then Q must be removed from the woken list of its
possible waker bfq_queue, and all bfq_queues in the woken list of Q
must stop having a waker bfq_queue.

Q remains with no I/O source in two cases: when the last process
associated with Q exits or when such a process gets associated with a
different bfq_queue. Unfortunately, commit 13a857a4c4e8 ("block, bfq:
detect wakers and unconditionally inject their I/O") performed the
above updates only in the first case.

This commit fixes this bug by moving these updates to when Q gets
freed. This is a simple and safe way to handle all cases, as both the
above events, process exit and re-association, lead to Q being freed
soon, and because dangling references would come out only after Q gets
freed (if no update were performed).

Fixes: 13a857a4c4e8 ("block, bfq: detect wakers and unconditionally inject their I/O")
Reported-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

block, bfq: reset last_completed_rq_bfqq if the pointed queue is freed

Since commit 13a857a4c4e8 ("block, bfq: detect wakers and
unconditionally inject their I/O"), BFQ stores, in a per-device
pointer last_completed_rq_bfqq, the last bfq_queue that had an I/O
request completed. If some bfq_queue receives new I/O right after the
last request of last_completed_rq_bfqq has been completed, then
last_completed_rq_bfqq may be a waker bfq_queue.

But if the bfq_queue last_completed_rq_bfqq points to is freed, then
last_completed_rq_bfqq becomes a dangling reference. This commit
resets last_completed_rq_bfqq if the pointed bfq_queue is freed.

Fixes: 13a857a4c4e8 ("block, bfq: detect wakers and unconditionally inject their I/O")
Reported-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

block: aoe: Fix kernel crash due to atomic sleep when exiting

Since commit 3582dd291788 ("aoe: convert aoeblk to blk-mq"), aoedev_downdev
has had the possibility of sleeping and causing the following crash.

BUG: scheduling while atomic: rmmod/2242/0x00000003
Modules linked in: aoe
Preemption disabled at:
[<ffffffffc01d95e5>] flush+0x95/0x4a0 [aoe]
CPU: 7 PID: 2242 Comm: rmmod Tainted: G I 5.2.3 #1
Hardware name: Intel Corporation S5520HC/S5520HC, BIOS S5500.86B.01.10.0025.030220091519 03/02/2009
Call Trace:
dump_stack+0x4f/0x6a
? flush+0x95/0x4a0 [aoe]
__schedule_bug.cold+0x44/0x54
__schedule+0x44f/0x680
schedule+0x44/0xd0
blk_mq_freeze_queue_wait+0x46/0xb0
? wait_woken+0x80/0x80
blk_mq_freeze_queue+0x1b/0x20
aoedev_downdev+0x111/0x160 [aoe]
flush+0xff/0x4a0 [aoe]
aoedev_exit+0x23/0x30 [aoe]
aoe_exit+0x35/0x948 [aoe]
__se_sys_delete_module+0x183/0x210
__x64_sys_delete_module+0x16/0x20
do_syscall_64+0x4d/0x130
entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x7f24e0043b07
Code: 73 01 c3 48 8b 0d 89 73 0b 00 f7 d8 64 89 01 48 83 c8 ff c3 66 2e 0f
1f 84 00 00 00 00 00 0f 1f 44 00 00 b8 b0 00 00 00 0f 05 <48> 3d 01 f0 ff
ff 73 01 c3 48 8b 0d 59 73 0b 00 f7 d8 64 89 01 48
RSP: 002b:00007ffe18f7f1e8 EFLAGS: 00000206 ORIG_RAX: 00000000000000b0
RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f24e0043b07
RDX: 000000000000000a RSI: 0000000000000800 RDI: 0000555c3ecf87c8
RBP: 00007ffe18f7f1f0 R08: 0000000000000000 R09: 0000000000000000
R10: 00007f24e00b4ac0 R11: 0000000000000206 R12: 00007ffe18f7f238
R13: 00007ffe18f7f410 R14: 00007ffe18f80e73 R15: 0000555c3ecf8760

This patch, handling in the same way of pass two, unlocks the locks and
restart pass one after aoedev_downdev is done.

Fixes: 3582dd291788 ("aoe: convert aoeblk to blk-mq")
Signed-off-by: He Zhe <zhe.he@windriver.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

s390/build: use size command to perform empty .bss check

Currently empty .bss checks performed do not pay attention to "common
objects" in object files which end up in .bss section eventually.

The "size" tool is a part of binutils and since version 2.18 provides
"--common" command line option, which allows to account "common objects"
sizes in .bss section size. Utilize "size --common" to perform accurate
check that .bss section is unused. Besides that the size tool handles
object files without .bss section gracefully and doesn't require
additional objdump run.

The linux kernel requires binutils 2.20 since 4.13.

Kbuild exports OBJSIZE to reference the right size tool.

Link: http://lkml.kernel.org/r/patch-2.thread-2257a1.git-2257a1c53d4a.your-ad-here.call-01565088755-ext-5120@work.hours
Reported-and-tested-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>

kbuild: add OBJSIZE variable for the size tool

Define and export OBJSIZE variable for "size" tool from binutils to be
used in architecture specific Makefiles (naming the variable just "SIZE"
would be too risky). In particular this tool is useful to perform checks
that early boot code is not using bss section (which might have not been
zeroed yet or intersects with initrd or other files boot loader might
have put right after the linux kernel).

Link: http://lkml.kernel.org/r/patch-1.thread-2257a1.git-188f5a3d81d5.your-ad-here.call-01565088755-ext-5120@work.hours
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>

pwm: Fallback to the static lookup-list when acpi_pwm_get fails

Commit 4a6ef8e37c4d ("pwm: Add support referencing PWMs from ACPI")
made pwm_get unconditionally return the acpi_pwm_get return value if
the device passed to pwm_get has an ACPI fwnode.

But even if the passed in device has an ACPI fwnode, it does not
necessarily have the necessary ACPI package defining its pwm bindings,
especially since the binding / API of this ACPI package has only been
introduced very recently.

Up until now X86/ACPI devices which use a separate pwm controller for
controlling their LCD screen's backlight brightness have been relying
on the static lookup-list to get their pwm.

pwm_get unconditionally returning the acpi_pwm_get return value breaks
this, breaking backlight control on these devices.

This commit fixes this by making pwm_get fall back to the static
lookup-list if acpi_pwm_get returns -ENOENT.

BugLink: https://bugs.freedesktop.org/show_bug.cgi?id=96571
Reported-by: youling257@gmail.com
Fixes: 4a6ef8e37c4d ("pwm: Add support referencing PWMs from ACPI")
Cc: Nikolaus Voss <nikolaus.voss@loewensteinmedical.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Nikolaus Voss <nikolaus.voss@loewensteinmedical.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

drm/vmwgfx: fix memory leak when too many retries have occurred

Currently when too many retries have occurred there is a memory
leak on the allocation for reply on the error return path. Fix
this by kfree'ing reply before returning.

Addresses-Coverity: ("Resource leak")
Fixes: a9cd9c044aa9 ("drm/vmwgfx: Add a check to handle host message failure")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Deepak Rawat <drawat@vmware.com>
Signed-off-by: Deepak Rawat <drawat@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>

ALSA: firewire: fix a memory leak bug

In iso_packets_buffer_init(), 'b->packets' is allocated through
kmalloc_array(). Then, the aligned packet size is checked. If it is
larger than PAGE_SIZE, -EINVAL will be returned to indicate the error.
However, the allocated 'b->packets' is not deallocated on this path,
leading to a memory leak.

To fix the above issue, free 'b->packets' before returning the error code.

Fixes: 31ef9134eb52 ("ALSA: add LaCie FireWire Speakers/Griffin FireWave Surround driver")
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Cc: <stable@vger.kernel.org> # v2.6.39+
Signed-off-by: Takashi Iwai <tiwai@suse.de>

sound: fix a memory leak bug

In sound_insert_unit(), the controlling structure 's' is allocated through
kmalloc(). Then it is added to the sound driver list by invoking
__sound_insert_unit(). Later on, if __register_chrdev() fails, 's' is
removed from the list through __sound_remove_unit(). If 'index' is not less
than 0, -EBUSY is returned to indicate the error. However, 's' is not
deallocated on this execution path, leading to a memory leak bug.

To fix the above issue, free 's' before -EBUSY is returned.

Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Merge tag 'drm-fixes-5.3-2019-08-07' of git://people.freedesktop.org/~agd5f/linux into drm-fixes

drm-fixes-5.3-2019-08-07:

amdgpu:
- Fixes VCN to handle the latest navi10 firmware
- Fixes for fan control on navi10
- Properly handle SMU metrics table on navi10
- Fix a resume regression on Stoney

amdkfd:
- Revert new GWS ioctl. It's not ready.

Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190807184221.3323-1-alexander.deucher@amd.com

Merge tag 'drm/tegra/for-5.3-rc4' of git://anongit.freedesktop.org/tegra/linux into drm-fixes

drm/tegra: Fixes for v5.3-rc4

This contains a single fix for a regression introduced by a combination
of a GPIO and a drm/tegra patch merged in v5.3-rc1.

Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thierry Reding <thierry.reding@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190807140634.29166-1-thierry.reding@gmail.com

Merge tag 'hwmon-for-v5.3-rc4' of git://git./linux/kernel/git/groeck/linux-staging

Pull hwmon fixes from Guenter Roeck:
"Fixes to lm75 and nct7802 drivers

  In the lm75 driver, fix TMP75B chip description to ensure correct
  initialization. In the nct7802 driver, fix in4 presence detection"

* tag 'hwmon-for-v5.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (lm75) Fixup tmp75b clr_mask
  hwmon: (nct7802) Fix wrong detection of in4 presence

hwmon: (lm75) Fixup tmp75b clr_mask

The configuration register of the tmp75b sensor is 16bit long, however
the first byte is reserved, so there is not no need to take care of it.

Because the order of the bytes is little endian and it is only necessary
to write one byte, the desired bits must be shifted into a 8 bit range.

Fixes: 39abe9d88b30 ("hwmon: (lm75) Add support for TMP75B")
Cc: stable@vger.kernel.org
Signed-off-by: Iker Perez del Palomar Sustatxa <iker.perez@codethink.co.uk>
Link: https://lore.kernel.org/r/20190801075324.4638-1-iker.perez@codethink.co.uk
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

hwmon: (nct7802) Fix wrong detection of in4 presence

The code to detect if in4 is present is wrong; if in4 is not present,
the in4_input sysfs attribute is still present.

In detail:

- Ihen RTD3_MD=11 (VSEN3 present), everything is as expected (no bug).
- If we have RTD3_MD!=11 (no VSEN3), we unexpectedly have a in4_input
file under /sys and the "sensors" command displays in4_input.
But as expected, we have no in4_min, in4_max, in4_alarm, in4_beep.

Fix is_visible function to detect and report in4_input visibility
as expected.

Reported-by: Gilles Buloz <Gilles.Buloz@kontron.com>
Cc: Gilles Buloz <Gilles.Buloz@kontron.com>
Cc: stable@vger.kernel.org
Fixes: 3434f37835804 ("hwmon: Driver for Nuvoton NCT7802Y")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

libata: add SG safety checks in SFF pio transfers

Abort processing of a command if we run out of mapped data in the
SG list. This should never happen, but a previous bug caused it to
be possible. Play it safe and attempt to abort nicely if we don't
have more SG segments left.

Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

libata: have ata_scsi_rw_xlat() fail invalid passthrough requests

For passthrough requests, libata-scsi takes what the user passes in
as gospel. This can be problematic if the user fills in the CDB
incorrectly. One example of that is in request sizes. For read/write
commands, the CDB contains fields describing the transfer length of
the request. These should match with the SG_IO header fields, but
libata-scsi currently does no validation of that.

Check that the number of blocks in the CDB for passthrough requests
matches what was mapped into the request. If the CDB asks for more
data then the validated SG_IO header fields, error it.

Reported-by: Krishna Ram Prakash R <krp@gtux.in>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

block: fix O_DIRECT error handling for bio fragments

0eb6ddfb865c tried to fix this up, but introduced a use-after-free
of dio. Additionally, we still had an issue with error handling,
as reported by Darrick:

"I noticed a regression in xfs/747 (an unreleased xfstest for the
xfs_scrub media scanning feature) on 5.3-rc3.  I'll condense that down
to a simpler reproducer:

error-test: 0 209 linear 8:48 0
error-test: 209 1 error
error-test: 210 6446894 linear 8:48 210

Basically we have a ~3G /dev/sdd and we set up device mapper to fail IO
for sector 209 and to pass the io to the scsi device everywhere else.

On 5.3-rc3, performing a directio pread of this range with a < 1M buffer
(in other words, a request for fewer than MAX_BIO_PAGES bytes) yields
EIO like you'd expect:

pread64(3, 0x7f880e1c7000, 1048576, 0)  = -1 EIO (Input/output error)
pread: Input/output error
+++ exited with 0 +++

But doing it with a larger buffer succeeds(!):

pread64(3, "XFSB\0\0\20\0\0\0\0\0\0\fL\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0"..., 1146880, 0) = 1146880
read 1146880/1146880 bytes at offset 0
1 MiB, 1 ops; 0.0009 sec (1.124 GiB/sec and 1052.6316 ops/sec)
+++ exited with 0 +++

(Note that the part of the buffer corresponding to the dm-error area is
uninitialized)

On 5.3-rc2, both commands would fail with EIO like you'd expect.  The
only change between rc2 and rc3 is commit 0eb6ddfb865c ("block: Fix
__blkdev_direct_IO() for bio fragments").

AFAICT we end up in __blkdev_direct_IO with a 1120K buffer, which gets
split into two bios: one for the first BIO_MAX_PAGES worth of data (1MB)
and a second one for the 96k after that."

Fix this by noting that it's always safe to dereference dio if we get
BLK_QC_T_EAGAIN returned, as end_io hasn't been run for that case. So
we can safely increment the dio size before calling submit_bio(), and
then decrement it on failure (not that it really matters, as the bio
and dio are going away).

For error handling, return to the original method of just using 'ret'
for tracking the error, and the size tracking in dio->size.

Fixes: 0eb6ddfb865c ("block: Fix __blkdev_direct_IO() for bio fragments")
Fixes: 6a43074e2f46 ("block: properly handle IOCB_NOWAIT for async O_DIRECT IO")
Reported-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

NFSv4: Ensure state recovery handles ETIMEDOUT correctly

Ensure that the state recovery code handles ETIMEDOUT correctly,
and also that we set RPC_TASK_TIMEOUT when recovering open state.

Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>

Revert "drm/amdkfd: New IOCTL to allocate queue GWS"

This reverts commit 1a058c3376765ee31d65e28cbbb9d4ff15120056.

This interface is still in too much flux. Revert until
it's sorted out.

Acked-by: Oak Zeng <Oak.Zeng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

ALSA: hda - Workaround for crackled sound on AMD controller (1022:1457)

A long-time problem on the recent AMD chip (X370, X470, B450, etc with
PCI ID 1022:1457) with Realtek codecs is the crackled or distorted
sound for capture streams, as well as occasional playback hiccups.
After lengthy debugging sessions, the workarounds we've found are like
the following:

- Set up the proper driver caps for this controller, similar as the
  other AMD controller.

- Correct the DMA position reporting with the fixed FIFO size, which
  is similar like as workaround used for VIA chip set.

- Even after the position correction, PulseAudio still shows
  mysterious stalls of playback streams when a capture is triggered in
  timer-scheduled mode.  Since we have no clear way to eliminate the
  stall, pass the BATCH PCM flag for PA to suppress the tsched mode as
  a temporary workaround.

This patch implements the workarounds.  For the driver caps, it
defines a new preset, AXZ_DCAPS_PRESET_AMD_SB.  It enables the FIFO-
corrected position reporting (corresponding to the new position_fix=6)
and enforces the SNDRV_PCM_INFO_BATCH flag.

Note that the current implementation is merely a workaround.
Hopefully we'll find a better alternative in future, especially about
removing the BATCH flag hack again.

BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=195303
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Revert "PCI: Add missing link delays required by the PCIe spec"

Commit c2bf1fc212f7 ("PCI: Add missing link delays required by the PCIe
spec") turned out causing issues with some systems either by making them
unresponsive or slowing down runtime and system wide resume of PCIe
devices. While root cause for the unresponsiveness is still under
investigation given the amount of issues reported better to revert it
for now.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=204413
Link: https://lore.kernel.org/linux-pci/SL2P216MB01878BBCD75F21D882AEEA2880C60@SL2P216MB0187.KORP216.PROD.OUTLOOK.COM/
Link: https://lore.kernel.org/linux-pci/2857501d-c167-547d-c57d-d5d24ea1f1dc@molgen.mpg.de/
Reported-by: Matthias Andree <matthias.andree@gmx.de>
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reported-by: Nicholas Johnson <nicholas.johnson-opensource@outlook.com.au>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

ALSA: hiface: fix multiple memory leak bugs

In hiface_pcm_init(), 'rt' is firstly allocated through kzalloc(). Later
on, hiface_pcm_init_urb() is invoked to initialize 'rt->out_urbs[i]'. In
hiface_pcm_init_urb(), 'rt->out_urbs[i].buffer' is allocated through
kzalloc(). However, if hiface_pcm_init_urb() fails, both 'rt' and
'rt->out_urbs[i].buffer' are not deallocated, leading to memory leak bugs.
Also, 'rt->out_urbs[i].buffer' is not deallocated if snd_pcm_new() fails.

To fix the above issues, free 'rt' and 'rt->out_urbs[i].buffer'.

Fixes: a91c3fb2f842 ("Add M2Tech hiFace USB-SPDIF driver")
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Revert "drm/amdgpu: fix transform feedback GDS hang on gfx10 (v2)"

This reverts commit 9ed2c993d723129f85101e51b2ccc36ef5400a67.

SET_CONFIG_REG writes to memory if register shadowing is enabled,
causing a VM fault.

NGG streamout is unstable anyway, so all UMDs should use legacy
streamout. I think Mesa is the only driver using NGG streamout.

Signed-off-by: Marek Olšák <marek.olsak@amd.com>
Reviewed-by: Le Ma <Le.Ma@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Merge git://git./linux/kernel/git/netdev/net

Pull networking fixes from David Miller:
"Yeah I should have sent a pull request last week, so there is a lot
  more here than usual:

   1) Fix memory leak in ebtables compat code, from Wenwen Wang.

   2) Several kTLS bug fixes from Jakub Kicinski (circular close on
      disconnect etc.)

   3) Force slave speed check on link state recovery in bonding 802.3ad
      mode, from Thomas Falcon.

   4) Clear RX descriptor bits before assigning buffers to them in
      stmmac, from Jose Abreu.

   5) Several missing of_node_put() calls, mostly wrt. for_each_*() OF
      loops, from Nishka Dasgupta.

   6) Double kfree_skb() in peak_usb can driver, from Stephane Grosjean.

   7) Need to hold sock across skb->destructor invocation, from Cong
      Wang.

   8) IP header length needs to be validated in ipip tunnel xmit, from
      Haishuang Yan.

   9) Use after free in ip6 tunnel driver, also from Haishuang Yan.

  10) Do not use MSI interrupts on r8169 chips before RTL8168d, from
      Heiner Kallweit.

  11) Upon bridge device init failure, we need to delete the local fdb.
      From Nikolay Aleksandrov.

  12) Handle erros from of_get_mac_address() properly in stmmac, from
      Martin Blumenstingl.

  13) Handle concurrent rename vs. dump in netfilter ipset, from Jozsef
      Kadlecsik.

  14) Setting NETIF_F_LLTX on mac80211 causes complete breakage with
      some devices, so revert. From Johannes Berg.

  15) Fix deadlock in rxrpc, from David Howells.

  16) Fix Kconfig deps of enetc driver, we must have PHYLIB. From Yue
      Haibing.

  17) Fix mvpp2 crash on module removal, from Matteo Croce.

  18) Fix race in genphy_update_link, from Heiner Kallweit.

  19) bpf_xdp_adjust_head() stopped working with generic XDP when we
      fixes generic XDP to support stacked devices properly, fix from
      Jesper Dangaard Brouer.

  20) Unbalanced RCU locking in rt6_update_exception_stamp_rt(), from
      David Ahern.

  21) Several memory leaks in new sja1105 driver, from Vladimir Oltean"

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (214 commits)
  net: dsa: sja1105: Fix memory leak on meta state machine error path
  net: dsa: sja1105: Fix memory leak on meta state machine normal path
  net: dsa: sja1105: Really fix panic on unregistering PTP clock
  net: dsa: sja1105: Use the LOCKEDS bit for SJA1105 E/T as well
  net: dsa: sja1105: Fix broken learning with vlan_filtering disabled
  net: dsa: qca8k: Add of_node_put() in qca8k_setup_mdio_bus()
  net: sched: sample: allow accessing psample_group with rtnl
  net: sched: police: allow accessing police->params with rtnl
  net: hisilicon: Fix dma_map_single failed on arm64
  net: hisilicon: fix hip04-xmit never return TX_BUSY
  net: hisilicon: make hip04_tx_reclaim non-reentrant
  tc-testing: updated vlan action tests with batch create/delete
  net sched: update vlan action for batched events operations
  net: stmmac: tc: Do not return a fragment entry
  net: stmmac: Fix issues when number of Queues >= 4
  net: stmmac: xgmac: Fix XGMAC selftests
  be2net: disable bh with spin_lock in be_process_mcc
  net: cxgb3_main: Fix a resource leak in a error path in 'init_one()'
  net: ethernet: sun4i-emac: Support phy-handle property for finding PHYs
  net: bridge: move default pvid init/deinit to NETDEV_REGISTER/UNREGISTER
  ...

Merge branch 'sja1105-fixes'

Vladimir Oltean says:

====================
Fixes for SJA1105 DSA: FDBs, Learning and PTP

This is an assortment of functional fixes for the sja1105 switch driver
targeted for the "net" tree (although they apply on net-next just as
well).

Patch 1/5 ("net: dsa: sja1105: Fix broken learning with vlan_filtering
disabled") repairs a breakage introduced in the early development stages
of the driver: support for traffic from the CPU has broken "normal"
frame forwarding (based on DMAC) - there is connectivity through the
switch only because all frames are flooded.
I debated whether this patch qualifies as a fix, since it puts the
switch into a mode it has never operated in before (aka SVL). But
"normal" forwarding did use to work before the "Traffic support for
SJA1105 DSA driver" patchset, and arguably this patch should have been
part of that.
Also, it would be strange for this feature to be broken in the 5.2 LTS.

Patch 2/5 ("net: dsa: sja1105: Use the LOCKEDS bit for SJA1105 E/T as
well") is a simplification of a previous FDB-related patch that is
currently in the 5.3 rc's.

Patches 3/5 - 5/5 fix various crashes found while running linuxptp over the
switch ports for extended periods of time, or in conjunction with other
error conditions. The fixed-up commits were all introduced in 5.2.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: Fix memory leak on meta state machine error path

When RX timestamping is enabled and two link-local (non-meta) frames are
received in a row, this constitutes an error.

The tagger is always caching the last link-local frame, in an attempt to
merge it with the meta follow-up frame when that arrives. To recover
from the above error condition, the initial cached link-local frame is
dropped and the second frame in a row is cached (in expectance of the
second meta frame).

However, when dropping the initial link-local frame, its backing memory
was being leaked.

Fixes: f3097be21bf1 ("net: dsa: sja1105: Add a state machine for RX timestamping")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: Fix memory leak on meta state machine normal path

After a meta frame is received, it is associated with the cached
sp->data->stampable_skb from the DSA tagger private structure.

Cached means its refcount is incremented with skb_get() in order for
dsa_switch_rcv() to not free it when the tagger .rcv returns NULL.

The mistake is that skb_unref() is not the correct function to use. It
will correctly decrement the refcount (which will go back to zero) but
the skb memory will not be freed.  That is the job of kfree_skb(), which
also calls skb_unref().

But it turns out that freeing the cached stampable_skb is in fact not
necessary.  It is still a perfectly valid skb, and now it is even
annotated with the partial RX timestamp.  So remove the skb_copy()
altogether and simply pass the stampable_skb with a refcount of 1
(incremented by us, decremented by dsa_switch_rcv) up the stack.

Fixes: f3097be21bf1 ("net: dsa: sja1105: Add a state machine for RX timestamping")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: Really fix panic on unregistering PTP clock

The IS_ERR_OR_NULL(priv->clock) check inside
sja1105_ptp_clock_unregister() is preventing cancel_delayed_work_sync
from actually being run.

Additionally, sja1105_ptp_clock_unregister() does not actually get run,
when placed in sja1105_remove(). The DSA switch gets torn down, but the
sja1105 module does not get unregistered. So sja1105_ptp_clock_unregister
needs to be moved to sja1105_teardown, to be symmetrical with
sja1105_ptp_clock_register which is called from the DSA sja1105_setup.

It is strange to fix a "fixes" patch, but the probe failure can only be
seen when the attached PHY does not respond to MDIO (issue which I can't
pinpoint the reason to) and it goes away after I power-cycle the board.
This time the patch was validated on a failing board, and the kernel
panic from the fixed commit's message can no longer be seen.

Fixes: 29dd908d355f ("net: dsa: sja1105: Cancel PTP delayed work on unregister")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: Use the LOCKEDS bit for SJA1105 E/T as well

It looks like the FDB dump taken from first-generation switches also
contains information on whether entries are static or not. So use that
instead of searching through the driver's tables.

Fixes: d763778224ea ("net: dsa: sja1105: Implement is_static for FDB entries on E/T")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: Fix broken learning with vlan_filtering disabled

When put under a bridge with vlan_filtering 0, the SJA1105 ports will
flood all traffic as if learning was broken. This is because learning
interferes with the rx_vid's configured by dsa_8021q as unique pvid's.

So learning technically still *does* work, it's just that the learnt
entries never get matched due to their unique VLAN ID.

The setting that saves the day is Shared VLAN Learning, which on this
switch family works exactly as desired: VLAN tagging still works
(untagged traffic gets the correct pvid) and FDB entries are still
populated with the correct contents including VID. Also, a frame cannot
violate the forwarding domain restrictions enforced by its classified
VLAN. It is just that the VID is ignored when looking up the FDB for
taking a forwarding decision (selecting the egress port).

This patch activates SVL, and the result is that frames with a learnt
DMAC are no longer flooded in the scenario described above.

Now exactly *because* SVL works as desired, we have to revisit some
earlier patches:

- It is no longer necessary to manipulate the VID of the 'bridge fdb
  {add,del}' command when vlan_filtering is off. This is because now,
  SVL is enabled for that case, so the actual VID does not matter*.

- It is still desirable to hide dsa_8021q VID's in the FDB dump
  callback. But right now the dump callback should no longer hide
  duplicates (one per each front panel port's pvid, plus one for the
  VLAN that the CPU port is going to tag a TX frame with), because there
  shouldn't be any (the switch will match a single FDB entry no matter
  its VID anyway).

* Not really... It's no longer necessary to transform a 'bridge fdb add'
  into 5 fdb add operations, but the user might still add a fdb entry with
  any vid, and all of them would appear as duplicates in 'bridge fdb
  show'. So force a 'bridge fdb add' to insert the VID of 0**, so that we
  can prune the duplicates at insertion time.

** The VID of 0 is better than 1 because it is always guaranteed to be
   in the ports' hardware filter. DSA also avoids putting the VID inside
   the netlink response message towards the bridge driver when we return
   this particular VID, which makes it suitable for FDB entries learnt
   with vlan_filtering off.

Fixes: 227d07a07ef1 ("net: dsa: sja1105: Add support for traffic through standalone ports")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Georg Waibel <georg.waibel@sensor-technik.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: qca8k: Add of_node_put() in qca8k_setup_mdio_bus()

Each iteration of for_each_available_child_of_node() puts the previous
node, but in the case of a return from the middle of the loop, there
is no put, thus causing a memory leak. Hence add an of_node_put() before
the return.
Additionally, the local variable ports in the function
qca8k_setup_mdio_bus() takes the return value of of_get_child_by_name(),
which gets a node but does not put it. If the function returns without
putting ports, it may cause a memory leak. Hence put ports before the
mid-loop return statement, and also outside the loop after its last usage
in this function.
Issues found with Coccinelle.

Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'flow_offload-action-fixes'

Vlad Buslov says:

====================
action fixes for flow_offload infra compatibility

Fix rcu warnings due to usage of action helpers that expect rcu read lock
protection from rtnl-protected context of flow_offload infra.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

net: sched: sample: allow accessing psample_group with rtnl

Recently implemented support for sample action in flow_offload infra leads
to following rcu usage warning:

[ 1938.234856] =============================
[ 1938.234858] WARNING: suspicious RCU usage
[ 1938.234863] 5.3.0-rc1+ #574 Not tainted
[ 1938.234866] -----------------------------
[ 1938.234869] include/net/tc_act/tc_sample.h:47 suspicious rcu_dereference_check() usage!
[ 1938.234872]
               other info that might help us debug this:

[ 1938.234875]
               rcu_scheduler_active = 2, debug_locks = 1
[ 1938.234879] 1 lock held by tc/19540:
[ 1938.234881]  #0: 00000000b03cb918 (rtnl_mutex){+.+.}, at: tc_new_tfilter+0x47c/0x970
[ 1938.234900]
               stack backtrace:
[ 1938.234905] CPU: 2 PID: 19540 Comm: tc Not tainted 5.3.0-rc1+ #574
[ 1938.234908] Hardware name: Supermicro SYS-2028TP-DECR/X10DRT-P, BIOS 2.0b 03/30/2017
[ 1938.234911] Call Trace:
[ 1938.234922]  dump_stack+0x85/0xc0
[ 1938.234930]  tc_setup_flow_action+0xed5/0x2040
[ 1938.234944]  fl_hw_replace_filter+0x11f/0x2e0 [cls_flower]
[ 1938.234965]  fl_change+0xd24/0x1b30 [cls_flower]
[ 1938.234990]  tc_new_tfilter+0x3e0/0x970
[ 1938.235021]  ? tc_del_tfilter+0x720/0x720
[ 1938.235028]  rtnetlink_rcv_msg+0x389/0x4b0
[ 1938.235038]  ? netlink_deliver_tap+0x95/0x400
[ 1938.235044]  ? rtnl_dellink+0x2d0/0x2d0
[ 1938.235053]  netlink_rcv_skb+0x49/0x110
[ 1938.235063]  netlink_unicast+0x171/0x200
[ 1938.235073]  netlink_sendmsg+0x224/0x3f0
[ 1938.235091]  sock_sendmsg+0x5e/0x60
[ 1938.235097]  ___sys_sendmsg+0x2ae/0x330
[ 1938.235111]  ? __handle_mm_fault+0x12cd/0x19e0
[ 1938.235125]  ? __handle_mm_fault+0x12cd/0x19e0
[ 1938.235138]  ? find_held_lock+0x2b/0x80
[ 1938.235147]  ? do_user_addr_fault+0x22d/0x490
[ 1938.235160]  __sys_sendmsg+0x59/0xa0
[ 1938.235178]  do_syscall_64+0x5c/0xb0
[ 1938.235187]  entry_SYSCALL_64_after_hwframe+0x49/0xbe
[ 1938.235192] RIP: 0033:0x7ff9a4d597b8
[ 1938.235197] Code: 89 02 48 c7 c0 ff ff ff ff eb bb 0f 1f 80 00 00 00 00 f3 0f 1e fa 48 8d 05 65 8f 0c 00 8b 00 85 c0 75 17 b8 2e 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 58 c3 0f 1f 80 00 00 00 00 48 83
ec 28 89 54
[ 1938.235200] RSP: 002b:00007ffcfe381c48 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
[ 1938.235205] RAX: ffffffffffffffda RBX: 000000005d4497f9 RCX: 00007ff9a4d597b8
[ 1938.235208] RDX: 0000000000000000 RSI: 00007ffcfe381cb0 RDI: 0000000000000003
[ 1938.235211] RBP: 0000000000000000 R08: 0000000000000001 R09: 0000000000000006
[ 1938.235214] R10: 0000000000404ec2 R11: 0000000000000246 R12: 0000000000000001
[ 1938.235217] R13: 0000000000480640 R14: 0000000000000012 R15: 0000000000000001

Change tcf_sample_psample_group() helper to allow using it from both rtnl
and rcu protected contexts.

Fixes: a7a7be6087b0 ("net/sched: add sample action to the hardware intermediate representation")
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: sched: police: allow accessing police->params with rtnl

Recently implemented support for police action in flow_offload infra leads
to following rcu usage warning:

[ 1925.881092] =============================
[ 1925.881094] WARNING: suspicious RCU usage
[ 1925.881098] 5.3.0-rc1+ #574 Not tainted
[ 1925.881100] -----------------------------
[ 1925.881104] include/net/tc_act/tc_police.h:57 suspicious rcu_dereference_check() usage!
[ 1925.881106]
               other info that might help us debug this:

[ 1925.881109]
               rcu_scheduler_active = 2, debug_locks = 1
[ 1925.881112] 1 lock held by tc/18591:
[ 1925.881115]  #0: 00000000b03cb918 (rtnl_mutex){+.+.}, at: tc_new_tfilter+0x47c/0x970
[ 1925.881124]
               stack backtrace:
[ 1925.881127] CPU: 2 PID: 18591 Comm: tc Not tainted 5.3.0-rc1+ #574
[ 1925.881130] Hardware name: Supermicro SYS-2028TP-DECR/X10DRT-P, BIOS 2.0b 03/30/2017
[ 1925.881132] Call Trace:
[ 1925.881138]  dump_stack+0x85/0xc0
[ 1925.881145]  tc_setup_flow_action+0x1771/0x2040
[ 1925.881155]  fl_hw_replace_filter+0x11f/0x2e0 [cls_flower]
[ 1925.881175]  fl_change+0xd24/0x1b30 [cls_flower]
[ 1925.881200]  tc_new_tfilter+0x3e0/0x970
[ 1925.881231]  ? tc_del_tfilter+0x720/0x720
[ 1925.881243]  rtnetlink_rcv_msg+0x389/0x4b0
[ 1925.881250]  ? netlink_deliver_tap+0x95/0x400
[ 1925.881257]  ? rtnl_dellink+0x2d0/0x2d0
[ 1925.881264]  netlink_rcv_skb+0x49/0x110
[ 1925.881275]  netlink_unicast+0x171/0x200
[ 1925.881284]  netlink_sendmsg+0x224/0x3f0
[ 1925.881299]  sock_sendmsg+0x5e/0x60
[ 1925.881305]  ___sys_sendmsg+0x2ae/0x330
[ 1925.881309]  ? task_work_add+0x43/0x50
[ 1925.881314]  ? fput_many+0x45/0x80
[ 1925.881329]  ? __lock_acquire+0x248/0x1930
[ 1925.881342]  ? find_held_lock+0x2b/0x80
[ 1925.881347]  ? task_work_run+0x7b/0xd0
[ 1925.881359]  __sys_sendmsg+0x59/0xa0
[ 1925.881375]  do_syscall_64+0x5c/0xb0
[ 1925.881381]  entry_SYSCALL_64_after_hwframe+0x49/0xbe
[ 1925.881384] RIP: 0033:0x7feb245047b8
[ 1925.881388] Code: 89 02 48 c7 c0 ff ff ff ff eb bb 0f 1f 80 00 00 00 00 f3 0f 1e fa 48 8d 05 65 8f 0c 00 8b 00 85 c0 75 17 b8 2e 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 58 c3 0f 1f 80 00 00 00 00 48 83
ec 28 89 54
[ 1925.881391] RSP: 002b:00007ffc2d2a5788 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
[ 1925.881395] RAX: ffffffffffffffda RBX: 000000005d4497ed RCX: 00007feb245047b8
[ 1925.881398] RDX: 0000000000000000 RSI: 00007ffc2d2a57f0 RDI: 0000000000000003
[ 1925.881400] RBP: 0000000000000000 R08: 0000000000000001 R09: 0000000000000006
[ 1925.881403] R10: 0000000000404ec2 R11: 0000000000000246 R12: 0000000000000001
[ 1925.881406] R13: 0000000000480640 R14: 0000000000000012 R15: 0000000000000001

Change tcf_police_rate_bytes_ps() and tcf_police_tcfp_burst() helpers to
allow using them from both rtnl and rcu protected contexts.

Fixes: 8c8cfc6ed274 ("net/sched: add police action to the hardware intermediate representation")
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'hisilicon-fixes'

Jiangfeng Xiao says:

====================
net: hisilicon: Fix a few problems with hip04_eth

During the use of the hip04_eth driver,
several problems were found,
which solved the hip04_tx_reclaim reentry problem,
fixed the problem that hip04_mac_start_xmit never
returns NETDEV_TX_BUSY
and the dma_map_single failed on the arm64 platform.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

net: hisilicon: Fix dma_map_single failed on arm64

On the arm64 platform, executing "ifconfig eth0 up" will fail,
returning "ifconfig: SIOCSIFFLAGS: Input/output error."

ndev->dev is not initialized, dma_map_single->get_dma_ops->
dummy_dma_ops->__dummy_map_page will return DMA_ERROR_CODE
directly, so when we use dma_map_single, the first parameter
is to use the device of platform_device.

Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hisilicon: fix hip04-xmit never return TX_BUSY

TX_DESC_NUM is 256, in tx_count, the maximum value of
mod(TX_DESC_NUM - 1) is 254, the variable "count" in
the hip04_mac_start_xmit function is never equal to
(TX_DESC_NUM - 1), so hip04_mac_start_xmit never
return NETDEV_TX_BUSY.

tx_count is modified to mod(TX_DESC_NUM) so that
the maximum value of tx_count can reach
(TX_DESC_NUM - 1), then hip04_mac_start_xmit can reurn
NETDEV_TX_BUSY.

Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hisilicon: make hip04_tx_reclaim non-reentrant

If hip04_tx_reclaim is interrupted while it is running
and then __napi_schedule continues to execute
hip04_rx_poll->hip04_tx_reclaim, reentrancy occurs
and oops is generated. So you need to mask the interrupt
during the hip04_tx_reclaim run.

The kernel oops exception stack is as follows:

Unable to handle kernel NULL pointer dereference
at virtual address 00000050
pgd = c0003000
[00000050] *pgd=80000000a04003, *pmd=00000000
Internal error: Oops: 206 [#1] SMP ARM
Modules linked in: hip04_eth mtdblock mtd_blkdevs mtd
ohci_platform ehci_platform ohci_hcd ehci_hcd
vfat fat sd_mod usb_storage scsi_mod usbcore usb_common
CPU: 0 PID: 0 Comm: swapper/0 Tainted: G           O    4.4.185 #1
Hardware name: Hisilicon A15
task: c0a250e0 task.stack: c0a00000
PC is at hip04_tx_reclaim+0xe0/0x17c [hip04_eth]
LR is at hip04_tx_reclaim+0x30/0x17c [hip04_eth]
pc : [<bf30c3a4>]    lr : [<bf30c2f4>]    psr: 600e0313
sp : c0a01d88  ip : 00000000  fp : c0601f9c
r10: 00000000  r9 : c3482380  r8 : 00000001
r7 : 00000000  r6 : 000000e1  r5 : c3482000  r4 : 0000000c
r3 : f2209800  r2 : 00000000  r1 : 00000000  r0 : 00000000
Flags: nZCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment kernel
Control: 32c5387d  Table: 03d28c80  DAC: 55555555
Process swapper/0 (pid: 0, stack limit = 0xc0a00190)
Stack: (0xc0a01d88 to 0xc0a02000)
[<bf30c3a4>] (hip04_tx_reclaim [hip04_eth]) from [<bf30d2e0>]
                                                (hip04_rx_poll+0x88/0x368 [hip04_eth])
[<bf30d2e0>] (hip04_rx_poll [hip04_eth]) from [<c04c2d9c>] (net_rx_action+0x114/0x34c)
[<c04c2d9c>] (net_rx_action) from [<c021eed8>] (__do_softirq+0x218/0x318)
[<c021eed8>] (__do_softirq) from [<c021f284>] (irq_exit+0x88/0xac)
[<c021f284>] (irq_exit) from [<c0240090>] (msa_irq_exit+0x11c/0x1d4)
[<c0240090>] (msa_irq_exit) from [<c02677e0>] (__handle_domain_irq+0x110/0x148)
[<c02677e0>] (__handle_domain_irq) from [<c0201588>] (gic_handle_irq+0xd4/0x118)
[<c0201588>] (gic_handle_irq) from [<c0551700>] (__irq_svc+0x40/0x58)
Exception stack(0xc0a01f30 to 0xc0a01f78)
1f20:                                     c0ae8b40 00000000 00000000 00000000
1f40: 00000002 ffffe000 c0601f9c 00000000 ffffffff c0a2257c c0a22440 c0831a38
1f60: c0a01ec4 c0a01f80 c0203714 c0203718 600e0213 ffffffff
[<c0551700>] (__irq_svc) from [<c0203718>] (arch_cpu_idle+0x20/0x3c)
[<c0203718>] (arch_cpu_idle) from [<c025bfd8>] (cpu_startup_entry+0x244/0x29c)
[<c025bfd8>] (cpu_startup_entry) from [<c054b0d8>] (rest_init+0xc8/0x10c)
[<c054b0d8>] (rest_init) from [<c0800c58>] (start_kernel+0x468/0x514)
Code: a40599e5 016086e2 018088e2 7660efe6 (503090e5)
---[ end trace 1db21d6d09c49d74 ]---
Kernel panic - not syncing: Fatal exception in interrupt
CPU3: stopping
CPU: 3 PID: 0 Comm: swapper/3 Tainted: G      D    O    4.4.185 #1

Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'Fix-batched-event-generation-for-vlan-action'

Roman Mashak says:

====================
Fix batched event generation for vlan action

When adding or deleting a batch of entries, the kernel sends up to
TCA_ACT_MAX_PRIO (defined to 32 in kernel) entries in an event to user
space. However it does not consider that the action sizes may vary and
require different skb sizes.

For example, consider the following script adding 32 entries with all
supported vlan parameters (in order to maximize netlink messages size):

% cat tc-batch.sh
TC="sudo /mnt/iproute2.git/tc/tc"

$TC actions flush action vlan
for i in `seq 1 $1`;
do
   cmd="action vlan push protocol 802.1q id 4094 priority 7 pipe \
               index $i cookie aabbccddeeff112233445566778800a1 "
   args=$args$cmd
done
$TC actions add $args
%
% ./tc-batch.sh 32
Error: Failed to fill netlink attributes while adding TC action.
We have an error talking to the kernel
%

patch 1 adds callback in tc_action_ops of vlan action, which calculates
the action size, and passes size to tcf_add_notify()/tcf_del_notify().

patch 2 updates the TDC test suite with relevant vlan test cases.
====================

Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tc-testing: updated vlan action tests with batch create/delete

Update TDC tests with cases varifying ability of TC to install or delete
batches of vlan actions.

Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net sched: update vlan action for batched events operations

Add get_fill_size() routine used to calculate the action size
when building a batch of events.

Fixes: c7e2b9689 ("sched: introduce vlan action")
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'mips_fixes_5.3_1' of git://git./linux/kernel/git/mips/linux

Pull MIPS fixes from Paul Burton:
"A few MIPS fixes for 5.3:

   - Various switch fall through annotations to fixup warnings & errors
     resulting from -Wimplicit-fallthrough.

   - A fix for systems (at least jazz) using an i8253 PIT as clocksource
     when it's not suitably configured.

   - Set struct cacheinfo's cpu_map_populated field to true, indicating
     that we filled in cache info detected from cop0 registers &
     avoiding complaints about that info being (intentionally) missing
     in devicetree"

* tag 'mips_fixes_5.3_1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
  MIPS: BCM63XX: Mark expected switch fall-through
  MIPS: OProfile: Mark expected switch fall-throughs
  MIPS: Annotate fall-through in Cavium Octeon code
  MIPS: Annotate fall-through in kvm/emulate.c
  mips: fix cacheinfo
  MIPS: kernel: only use i8253 clocksource with periodic clockevent

drm/amdgpu: pin the csb buffer on hw init for gfx v8

Without this pin, the csb buffer will be filled with inconsistent
data after S3 resume. And that will causes gfx hang on gfxoff
exit since this csb will be executed then.

Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Tested-by: Paul Gover <pmw.gover@yahoo.co.uk>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Reviewed-by: Xiaojie Yuan <xiaojie.yuan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Merge branch 'stmmac-fixes'

Jose Abreu says:

====================
net: stmmac: Fixes for -net

Couple of fixes for -net. More info in commit log.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

net: stmmac: tc: Do not return a fragment entry

Do not try to return a fragment entry from TC list. Otherwise we may not
clean properly allocated entries.

Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: stmmac: Fix issues when number of Queues >= 4

When queues >= 4 we use different registers but we were not subtracting
the offset of 4. Fix this.

Found out by Coverity.

Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: stmmac: xgmac: Fix XGMAC selftests

Fixup the XGMAC selftests by correctly finishing the implementation of
set_filter callback.

Result:
$ ethtool -t enp4s0
The test result is PASS
The test extra info:
1. MAC Loopback          0
2. PHY Loopback          -95
3. MMC Counters          -95
4. EEE                   -95
5. Hash Filter MC        0
6. Perfect Filter UC     0
7. MC Filter             0
8. UC Filter             0
9. Flow Control          0

Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-for-davem-2019-08-06' of git://git./linux/kernel/git/kvalo/wireless-drivers

Kalle Valo says:

====================
wireless-drivers fixes for 5.3

Second set of fixes for 5.3. Lots of iwlwifi fixes have accumulated
which consists most of patches in this pull request. Only most notable
iwlwifi fixes are listed below.

mwifiex

* fix a regression related to WPA1 networks since v5.3-rc1

iwlwifi

* fix use-after-free issues

* fix DMA mapping API usage errors

* fix frame drop occurring due to reorder buffer handling in
RSS in certain conditions

* fix rate scale locking issues

* disable TX A-MSDU on older NICs as it causes problems and was
never supposed to be supported

* new PCI IDs

* GEO_TX_POWER_LIMIT API issue that many people were hitting
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'for-linus' of git://git./linux/kernel/git/hid/hid

Pull HID fixes from Jiri Kosina:

- functional regression fix for some of the Logitech unifying devices,
   from Hans de Goede

- race condition fix in hid-sony for bug severely affecting
   Valve/Android deployments, from Roderick Colenbrander

- several fixes for issues found by syzbot/kasan, from Oliver Neukum
   and Hillf Danton

- functional regression fix for Wacom Cintiq device, from Aaron
   Armstrong Skomra

- a few other assorted device-specific quirks

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
  HID: sony: Fix race condition between rumble and device remove.
  HID: hiddev: do cleanup in failure of opening a device
  HID: hiddev: avoid opening a disconnected device
  HID: input: fix a4tech horizontal wheel custom usage
  HID: Add quirk for HP X1200 PIXART OEM mouse
  HID: holtek: test for sanity of intfdata
  HID: wacom: fix bit shift for Cintiq Companion 2
  HID: quirks: Set the INCREMENT_USAGE_ON_DUPLICATE quirk on Saitek X52
  HID: logitech-dj: Really fix return value of logi_dj_recv_query_hidpp_devices
  HID: Add 044f:b320 ThrustMaster, Inc. 2 in 1 DT
  HID: logitech-dj: add the Powerplay receiver
  HID: logitech-hidpp: add USB PID for a few more supported mice
  HID: logitech-dj: rename "gaming" receiver to "lightspeed"

be2net: disable bh with spin_lock in be_process_mcc

be_process_mcc() is invoked in 3 different places and
always with BHs disabled except the be_poll function
but since it's invoked from softirq with BHs
disabled it won't hurt.

v1->v2: added explanation to the patch
v2->v3: add a missing call from be_cmds.c

Signed-off-by: Denis Kirjanov <kda@linux-powerpc.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: cxgb3_main: Fix a resource leak in a error path in 'init_one()'

A call to 'kfree_skb()' is missing in the error handling path of
'init_one()'.
This is already present in 'remove_one()' but is missing here.

Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ethernet: sun4i-emac: Support phy-handle property for finding PHYs

The sun4i-emac uses the "phy" property to find the PHY it's supposed to
use. This property was deprecated in favor of "phy-handle" in commit
8c5b09447625 ("dt-bindings: net: sun4i-emac: Convert the binding to a
schemas").

Add support for this new property name, and fall back to the old one in
case the device tree hasn't been updated.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'x86/grand-schemozzle' of git://git./linux/kernel/git/tip/tip

Pull pti updates from Thomas Gleixner:
"The performance deterioration departement is not proud at all to
  present yet another set of speculation fences to mitigate the next
  chapter in the 'what could possibly go wrong' story.

  The new vulnerability belongs to the Spectre class and affects GS
  based data accesses and has therefore been dubbed 'Grand Schemozzle'
  for secret communication purposes. It's officially listed as
  CVE-2019-1125.

  Conditional branches in the entry paths which contain a SWAPGS
  instruction (interrupts and exceptions) can be mis-speculated which
  results in speculative accesses with a wrong GS base.

  This can happen on entry from user mode through a mis-speculated
  branch which takes the entry from kernel mode path and therefore does
  not execute the SWAPGS instruction. The following speculative accesses
  are done with user GS base.

  On entry from kernel mode the mis-speculated branch executes the
  SWAPGS instruction in the entry from user mode path which has the same
  effect that the following GS based accesses are done with user GS
  base.

  If there is a disclosure gadget available in these code paths the
  mis-speculated data access can be leaked through the usual side
  channels.

  The entry from user mode issue affects all CPUs which have speculative
  execution. The entry from kernel mode issue affects only Intel CPUs
  which can speculate through SWAPGS. On CPUs from other vendors SWAPGS
  has semantics which prevent that.

  SMAP migitates both problems but only when the CPU is not affected by
  the Meltdown vulnerability.

  The mitigation is to issue LFENCE instructions in the entry from
  kernel mode path for all affected CPUs and on the affected Intel CPUs
  also in the entry from user mode path unless PTI is enabled because
  the CR3 write is serializing.

  The fences are as usual enabled conditionally and can be completely
  disabled on the kernel command line. The Spectre V1 documentation is
  updated accordingly.

  A big "Thank You!" goes to Josh for doing the heavy lifting for this
  round of hardware misfeature 'repair'. Of course also "Thank You!" to
  everybody else who contributed in one way or the other"

* 'x86/grand-schemozzle' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  Documentation: Add swapgs description to the Spectre v1 documentation
  x86/speculation/swapgs: Exclude ATOMs from speculation through SWAPGS
  x86/entry/64: Use JMP instead of JMPQ
  x86/speculation: Enable Spectre v1 swapgs mitigations
  x86/speculation: Prepare entry code for Spectre v1 swapgs mitigations

mmc: cavium: Add the missing dma unmap when the dma has finished.

This fixes the below calltrace when the CONFIG_DMA_API_DEBUG is enabled.
  DMA-API: thunderx_mmc 0000:01:01.4: cpu touching an active dma mapped cacheline [cln=0x000000002fdf9800]
  WARNING: CPU: 21 PID: 1 at kernel/dma/debug.c:596 debug_dma_assert_idle+0x1f8/0x270
  Modules linked in:
  CPU: 21 PID: 1 Comm: init Not tainted 5.3.0-rc1-next-20190725-yocto-standard+ #64
  Hardware name: Marvell OcteonTX CN96XX board (DT)
  pstate: 80400009 (Nzcv daif +PAN -UAO)
  pc : debug_dma_assert_idle+0x1f8/0x270
  lr : debug_dma_assert_idle+0x1f8/0x270
  sp : ffff0000113cfc10
  x29: ffff0000113cfc10 x28: 0000ffff8c880000
  x27: ffff800bc72a0000 x26: ffff000010ff8000
  x25: ffff000010ff8940 x24: ffff000010ff8968
  x23: 0000000000000000 x22: ffff000010e83700
  x21: ffff000010ea2000 x20: ffff000010e835c8
  x19: ffff800bc2c73300 x18: ffffffffffffffff
  x17: 0000000000000000 x16: 0000000000000000
  x15: ffff000010e835c8 x14: 6d20616d64206576
  x13: 69746361206e6120 x12: 676e696863756f74
  x11: 20757063203a342e x10: 31303a31303a3030
  x9 : 303020636d6d5f78 x8 : 3230303030303030
  x7 : 00000000000002fd x6 : ffff000010fd57d0
  x5 : 0000000000000000 x4 : ffff0000106c5210
  x3 : 00000000ffffffff x2 : 0000800bee9c0000
  x1 : 57d5843f4aa62800 x0 : 0000000000000000
  Call trace:
   debug_dma_assert_idle+0x1f8/0x270
   wp_page_copy+0xb0/0x688
   do_wp_page+0xa8/0x5b8
   __handle_mm_fault+0x600/0xd00
   handle_mm_fault+0x118/0x1e8
   do_page_fault+0x200/0x500
   do_mem_abort+0x50/0xb0
   el0_da+0x20/0x24
  ---[ end trace a005534bd23e109f ]---
  DMA-API: Mapped at:
   debug_dma_map_sg+0x94/0x350
   cvm_mmc_request+0x3c4/0x988
   __mmc_start_request+0x9c/0x1f8
   mmc_start_request+0x7c/0xb0
   mmc_blk_mq_issue_rq+0x5c4/0x7b8

Signed-off-by: Kevin Hao <haokexin@gmail.com>
Fixes: ba3869ff32e4 ("mmc: cavium: Add core MMC driver for Cavium SOCs")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: cavium: Set the correct dma max segment size for mmc_host

We have set the mmc_host.max_seg_size to 8M, but the dma max segment
size of PCI device is set to 64K by default in function pci_device_add().
The mmc_host.max_seg_size is used to set the max segment size of
the blk queue. Then this mismatch will trigger a calltrace like below
when a bigger than 64K segment request arrives at mmc dev. So we should
consider the limitation of the cvm_mmc_host when setting the
mmc_host.max_seg_size.
  DMA-API: thunderx_mmc 0000:01:01.4: mapping sg segment longer than device claims to support [len=131072] [max=65536]
  WARNING: CPU: 6 PID: 238 at kernel/dma/debug.c:1221 debug_dma_map_sg+0x2b8/0x350
  Modules linked in:
  CPU: 6 PID: 238 Comm: kworker/6:1H Not tainted 5.3.0-rc1-next-20190724-yocto-standard+ #62
  Hardware name: Marvell OcteonTX CN96XX board (DT)
  Workqueue: kblockd blk_mq_run_work_fn
  pstate: 80c00009 (Nzcv daif +PAN +UAO)
  pc : debug_dma_map_sg+0x2b8/0x350
  lr : debug_dma_map_sg+0x2b8/0x350
  sp : ffff00001770f9e0
  x29: ffff00001770f9e0 x28: ffffffff00000000
  x27: 00000000ffffffff x26: ffff800bc2c73180
  x25: ffff000010e83700 x24: 0000000000000002
  x23: 0000000000000001 x22: 0000000000000001
  x21: 0000000000000000 x20: ffff800bc48ba0b0
  x19: ffff800bc97e8c00 x18: ffffffffffffffff
  x17: 0000000000000000 x16: 0000000000000000
  x15: ffff000010e835c8 x14: 6874207265676e6f
  x13: 6c20746e656d6765 x12: 7320677320676e69
  x11: 7070616d203a342e x10: 31303a31303a3030
  x9 : 303020636d6d5f78 x8 : 35363d78616d5b20
  x7 : 00000000000002fd x6 : ffff000010fd57dc
  x5 : 0000000000000000 x4 : ffff0000106c61f0
  x3 : 00000000ffffffff x2 : 0000800bee060000
  x1 : 7010678df3041a00 x0 : 0000000000000000
  Call trace:
   debug_dma_map_sg+0x2b8/0x350
   cvm_mmc_request+0x3c4/0x988
   __mmc_start_request+0x9c/0x1f8
   mmc_start_request+0x7c/0xb0
   mmc_blk_mq_issue_rq+0x5c4/0x7b8
   mmc_mq_queue_rq+0x11c/0x278
   blk_mq_dispatch_rq_list+0xb0/0x568
   blk_mq_do_dispatch_sched+0x6c/0x108
   blk_mq_sched_dispatch_requests+0x110/0x1b8
   __blk_mq_run_hw_queue+0xb0/0x118
   blk_mq_run_work_fn+0x28/0x38
   process_one_work+0x210/0x490
   worker_thread+0x48/0x458
   kthread+0x130/0x138
   ret_from_fork+0x10/0x1c

Signed-off-by: Kevin Hao <haokexin@gmail.com>
Fixes: ba3869ff32e4 ("mmc: cavium: Add core MMC driver for Cavium SOCs")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sdhci-sprd: Fix the incorrect soft reset operation when runtime resuming

The SD host controller specification defines 3 types software reset:
software reset for data line, software reset for command line and software
reset for all. Software reset for all means this reset affects the entire
Host controller except for the card detection circuit.

In sdhci_runtime_resume_host() we always do a software "reset for all",
which causes the Spreadtrum variant controller to work abnormally after
resuming. To fix the problem, let's do a software reset for the data and
the command part, rather than "for all".

However, as sdhci_runtime_resume() is a common sdhci function and we don't
want to change the behaviour for other variants, let's introduce a new
in-parameter for it. This enables the caller to decide if a "reset for all"
shall be done or not.

Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Fixes: fb8bd90f83c4 ("mmc: sdhci-sprd: Add Spreadtrum's initial host controller")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Input: iforce - add sanity checks

The endpoint type should also be checked before a device
is accepted.

Reported-by: syzbot+5efc10c005014d061a74@syzkaller.appspotmail.com
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Input: applespi - use struct_size() helper

One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:

struct touchpad_protocol {
...
struct tp_finger fingers[0];
};

Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes.

So, replace the following form:

sizeof(*tp) + tp->number_of_fingers * sizeof(tp->fingers[0]);

with:

struct_size(tp, fingers, tp->number_of_fingers)

This code was detected with the help of Coccinelle.

Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

ata: rb532_cf: Fix unused variable warning in rb532_pata_driver_probe

Fix the following warning (Building: rb532_defconfig mips):

drivers/ata/pata_rb532_cf.c: In function ‘rb532_pata_driver_remove’:
drivers/ata/pata_rb532_cf.c:161:24: warning: unused variable ‘info’ [-Wunused-variable]
struct rb532_cf_info *info = ah->private_data;
^~~~

Fixes: cd56f35e52d9 ("ata: rb532_cf: Convert to use GPIO descriptors")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

ALSA: hda - Don't override global PCM hw info flag

The commit bfcba288b97f ("ALSA - hda: Add support for link audio time
reporting") introduced the conditional PCM hw info setup, but it
overwrites the global azx_pcm_hw object. This will cause a problem if
any other HD-audio controller, as it'll inherit the same bit flag
although another controller doesn't support that feature.

Fix the bug by setting the PCM hw info flag locally.

Fixes: bfcba288b97f ("ALSA - hda: Add support for link audio time reporting")
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>