Matthias Weisser [Thu, 10 Mar 2011 21:36:32 +0000 (21:36 +0000)]
arm: Use optimized memcpy and memset from linux
Using optimized versions of memset and memcpy from linux brings a quite
noticeable speed (x2 or better) improvement for these two functions.
Here are some numbers for test done with jadecpu
| HEAD(1)| HEAD(1)| HEAD(2)| HEAD(2)|
| | +patch | | +patch |
---------------------------+--------+--------+--------+--------+
Reset to prompt | 438ms | 330ms | 228ms | 120ms |
| | | | |
TFTP a 3MB img | 4782ms | 3428ms | 3245ms | 2820ms |
| | | | |
FATLOAD USB a 3MB img* | 8515ms | 8510ms | ------ | ------ |
| | | | |
BOOTM LZO img in RAM | 3473ms | 3168ms | 592ms | 592ms |
where CRC is | 615ms | 615ms | 54ms | 54ms |
uncompress | 2460ms | 2462ms | 450ms | 451ms |
final boot_elf | 376ms | 68ms | 65ms | 65ms |
| | | | |
BOOTM LZO img in FLASH | 3207ms | 2902ms | 1050ms | 1050ms |
where CRC is | 600ms | 600ms | 135ms | 135ms |
uncompress | 2209ms | 2211ms | 828ms | 828ms |
| | | | |
Copy 1.4MB from NOR to RAM | 134ms | 72ms | 120ms | 70ms |
(1) No dcache
(2) dcache enabled in board_init
*Does not work when dcache is on
Size impact:
C version:
text data bss dec hex filename
202862 18912 266456 488230 77326 u-boot
ASM version:
text data bss dec hex filename
203798 18912 266288 488998 77626 u-boot
222712 u-boot.bin
Signed-off-by: Matthias Weisser <weisserm@arcor.de>
Igor Grinberg [Mon, 18 Apr 2011 21:55:21 +0000 (17:55 -0400)]
OMAP3: CM-T35: Add support for CM-T3730
CM-T3730 is exactly the same board as CM-T35, but it has
TI DM3730 SoC onboard and therefore some changes have to take place
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Igor Grinberg [Mon, 18 Apr 2011 21:54:33 +0000 (17:54 -0400)]
OMAP3: CM-T35: enable the green LED
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Igor Grinberg [Mon, 18 Apr 2011 21:53:33 +0000 (17:53 -0400)]
OMAP3: CM-T35: remove redundand i2c initialization
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Igor Grinberg [Mon, 18 Apr 2011 21:52:31 +0000 (17:52 -0400)]
OMAP3: CM-T35: fix mmc
Use CONFIG_OMAP3_MMC in cm-t35 configuration file.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Igor Grinberg [Mon, 18 Apr 2011 21:50:07 +0000 (17:50 -0400)]
OMAP3: CM-T35: add MMC1 pinmux
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Igor Grinberg [Mon, 18 Apr 2011 21:49:26 +0000 (17:49 -0400)]
OMAP3: CM-T35: update MAINTAINERS file
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Igor Grinberg [Mon, 18 Apr 2011 21:48:31 +0000 (17:48 -0400)]
OMAP3: CM-T35: update board files header information
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Igor Grinberg [Mon, 18 Apr 2011 21:48:28 +0000 (17:48 -0400)]
OMAP3: CM-T35: update config
update config for OMAP3 CM-T35
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Igor Grinberg [Mon, 18 Apr 2011 21:43:26 +0000 (17:43 -0400)]
OMAP3: CM-T35: Move DECLARE_GLOBAL_DATA_PTR to file scope
Move DECLARE_GLOBAL_DATA_PTR to file scop
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Srinath [Mon, 18 Apr 2011 21:40:35 +0000 (17:40 -0400)]
ARMV7: AM3517/05: Add support for CraneBoard.
It is a low cost reference design based on Sitara AM3517 SoC from Texas Instruments
Please refer to <www.craneboard.org> for more details.
Signed-off-by: Srinath <srinath@mistralsolutions.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Koen Kooi [Mon, 18 Apr 2011 21:29:35 +0000 (17:29 -0400)]
OMAP3: BeagleBoard: add more expansionboard IDs
Information on configurations pulled from
http://www.elinux.org/BeagleBoardPinMux#Vendor_and_Device_IDs
Boards added:
* Added BeagleBoardToys WiFi, VGA and LCD boards
* Added KBADC Beagle FPGA board
* Added Brainmux LCDog and LCDog Touch
* Added Liquidware BeagleTouch
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Koen Kooi [Mon, 18 Apr 2011 21:28:32 +0000 (17:28 -0400)]
OMAP3: BeagleBoard: add xM rev B to ID table
Patch was updated by Jason Kridner <jkridner@beagleboard.org>:
* Use tabs to match style of other board revisions
* Only include board revisions that exist
* Default to the same configuration as the latest revision, but
without setting 'beaglerev'
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Steve Kipisz [Mon, 18 Apr 2011 21:27:00 +0000 (17:27 -0400)]
OMAP3: BeagleBoard: Enable pullups on i2c2.
This allows the reading of EEPROMS on the expansion bus without adding
external pull-ups.
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Alexander Holler [Mon, 18 Apr 2011 21:25:13 +0000 (17:25 -0400)]
omap3_beagle: enable the use of a plain text file
Using the new env import command it is possible to use plain text files instead
of script-images. Plain text files are much easier to handle.
E.g. If your boot.scr contains the following:
-----------------------------------
setenv dvimode 1024x768-16@60
run loaduimage
run mmcboot
-----------------------------------
you could create a file named uEnv.txt and use that instead of boot.scr:
-----------------------------------
dvimode=1024x768-16@60
uenvcmd=run loaduimage; run mmcboot
-----------------------------------
The variable uenvcmd (if existent) will be executed (using run) after uEnv.txt
was loaded. If uenvcmd doesn't exist the default boot sequence will be started,
therefore you could just use
-----------------------------------
dvimode=1024x768-16@60
-----------------------------------
as uEnv.txt because loaduimage and mmcboot is part of the default boot sequence
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Jason Kridner [Mon, 18 Apr 2011 21:23:35 +0000 (17:23 -0400)]
BeagleBoard: Added LED driver
Added LED driver using status_led. USR0 is set to monitor the boot
status. USR1 is set to be the green LED.
Included adding configuration and command to the default configuration.
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Jason Kridner [Mon, 18 Apr 2011 21:22:44 +0000 (17:22 -0400)]
Add 'led' command
This patch allows any board implementing the coloured LED API
to control the LEDs from the console.
led [green | yellow | red | all ] [ on | off ]
or
led [ 1 | 2 | 3 | all ] [ on | off ]
Adds configuration item CONFIG_CMD_LED enabling the command.
Partially based on patch from Ulf Samuelsson:
http://www.mail-archive.com/u-boot@lists.denx.de/msg09593.html.
Updated based on feedback:
http://www.mail-archive.com/u-boot@lists.denx.de/msg41847.html
https://groups.google.com/d/topic/beagleboard/8Wf1HiK_QBo/discussion
* Fixed a handful of style issues.
* Significantly reduced the number of #ifdefs and redundant code
* Converted redundant code into loops test against a structure
* Made use of cmd_usage()
* Introduced a str_onoff() function, but haven't yet put it in common
* Eliminated trailing newline
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Stefano Babic [Thu, 21 Apr 2011 16:01:33 +0000 (18:01 +0200)]
MX31: drop warnings in get_cpu_rev
Drop warnings due to recent commit
ARM: mx31: Print the silicon version
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
Jason Liu [Wed, 20 Apr 2011 00:47:04 +0000 (00:47 +0000)]
MX5: factor out boot cause funciton to common code
factor out boot cause function to common code to avoid
the duplicate code in each board support package
Signed-off-by: Jason Liu <jason.hui@linaro.org>
Fabio Estevam [Fri, 15 Apr 2011 16:54:50 +0000 (16:54 +0000)]
ARM: MX31: Fix file name label
Commit
5d2c154 (IMX: MX31: Cleanup include files and drop nasty #ifdef in drivers)
renamed mx31-imx-regs.h to imx-regs.h.
Change the file label accordingly.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Fabio Estevam [Mon, 18 Apr 2011 07:38:12 +0000 (07:38 +0000)]
MX31: mx31pdk: Make the board name simpler.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Fabio Estevam [Mon, 18 Apr 2011 07:38:11 +0000 (07:38 +0000)]
MX31: Introduce get_reset_cause()
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Detlev Zundel <dzu@denx.de>
Fabio Estevam [Mon, 11 Apr 2011 16:18:12 +0000 (16:18 +0000)]
ARM: mx31: Print the silicon version
Use the same method of the Linux kernel to print the MX31 silicon version on
boot.
Tested on a MX31PDK with a 2.0 silicon, where it shows:
CPU: Freescale i.MX31 rev 2.0 at 531 MHz
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Stefano Babic [Mon, 14 Mar 2011 14:43:56 +0000 (15:43 +0100)]
IMX: MX31: Cleanup include files and drop nasty #ifdef in drivers
As exception among the i.MX processors, the i.MX31 has headers
without general names (mx31-regs.h, mx31.h instead of imx-regs.h and
clock.h). This requires several nasty #ifdef in the drivers to
include the correct header. The patch cleans up the driver and
renames the header files as for the other i.MX processors.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Liu Hui-R64343 [Mon, 21 Feb 2011 00:14:33 +0000 (00:14 +0000)]
MX5: Enable flat-device-tree support on mx51/53 evk board
device tree for uboot arm support has already been enabled
in the master branch. This patch enable device tree support
for mx51/53 evk board for DT test.
Signed-off-by: Jason Liu <r64343@freescale.com>
Liu Hui-R64343 [Tue, 22 Feb 2011 21:26:09 +0000 (21:26 +0000)]
MX53: drop config.mk from mx53evk
The config.mk file in board directory is now obsolete and
should be removed. Add option for the IMX image into
boards.cfg
Signed-off-by: Jason Liu <r64343@freescale.com>
Fabio Estevam [Wed, 2 Mar 2011 09:14:27 +0000 (10:14 +0100)]
mx25: Make the UART port number explicit in its setup function
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Stefano Babic [Wed, 2 Feb 2011 00:49:37 +0000 (00:49 +0000)]
MX31: qong: add watchdog
Signed-off-by: Stefano Babic <sbabic@denx.de>
Stefano Babic [Wed, 2 Feb 2011 00:49:36 +0000 (00:49 +0000)]
MX31: add support for MX31 watchdog
The patch add CONFIG_HW_WATCHDOG to be used
with the internal watchdog timer of the MX31
processor. Two function are exported for the
board maintainers:
mxc_hw_watchdog_enable
mxc_hw_watchdog_reset
The board maintainer can decide to use mxc_hw_watchdog_reset as
hw_watchdog_reset, or to implement his own function to reset
the watchdog.
The watchdog timer can be configured with CONFIG_SYS_WD_TIMER_SECS
(value in seconds). The MX31 allows values between 0.5
(CONFIG_SYS_WD_TIMER_SECS = 0) and 128 seconds.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Stefano Babic [Mon, 24 Jan 2011 00:14:27 +0000 (00:14 +0000)]
MX51: drop config.mk from mx51evk
The config.mk file in board directory is now obsolete and
should be removed. Add option for the IMX image into
boards.cfg
Signed-off-by: Stefano Babic <sbabic@denx.de>
Stefano Babic [Mon, 24 Jan 2011 00:14:26 +0000 (00:14 +0000)]
Makefile: change rule to build IMX image
config.mk in board directory is obsolete and should be removed.
The patch allows to get rid of own config.mk adding the imximage.cfg
file to the options in the boards.cfg
Signed-off-by: Stefano Babic <sbabic@denx.de>
Heiko Schocher [Mon, 28 Mar 2011 07:24:23 +0000 (09:24 +0200)]
mpc52xx, digsy_mtc: add trickle charger support for rev5 boards.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
Heiko Schocher [Mon, 28 Mar 2011 07:24:22 +0000 (09:24 +0200)]
rtc, rv3029: add trickle charger support.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
Loïc Minier [Thu, 24 Mar 2011 16:21:42 +0000 (17:21 +0100)]
Fix typo in #error: IS_IN_NOWHERE vs. IS_NOWHERE
Signed-off-by: Loïc Minier <loic.minier@linaro.org>
Wolfgang Denk [Sun, 24 Apr 2011 22:58:45 +0000 (00:58 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-cfi-flash
Wolfgang Denk [Sun, 24 Apr 2011 22:55:26 +0000 (00:55 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-ppc4xx
Joakim Tjernlund [Sun, 24 Apr 2011 08:29:32 +0000 (10:29 +0200)]
powerpc, 8xx: Fix fallout from "Fixup all 8xx u-boot.lds scripts"
Two linker scripts for 8xx was missed.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Aaron Williams [Tue, 12 Apr 2011 07:59:04 +0000 (00:59 -0700)]
cfi_flash driver - Add delay after reset command
I ran into a problem where the reset was failing except when I enabled
debugging support. After talking with Garret Swalling at Spansion I
was told that the GL-N series of devices require a 500ns wait for the
reset to complete. The below patch adds a 1us delay after all reset
commands.
-Aaron Williams
Signed-off-by: Aaron Williams <aaron.williams@caviumnetworks.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Heiko Schocher [Mon, 11 Apr 2011 12:16:19 +0000 (14:16 +0200)]
mtd, cfi: read AMD 3-byte (expanded) device ids on 16bit devices
tested on the a4m072 board with a S29GL512P flash.
flinfo without this patch
Bank # 1: CFI conformant flash (16 x 16) Size: 32 MB in 256 Sectors
AMD Standard command set, Manufacturer ID: 0x01, Device ID: 0x227E
Erase timeout: 16384 ms, write timeout: 2 ms
Buffer write timeout: 5 ms, buffer size: 32 bytes
[...]
flinfo with this patch
Bank # 1: CFI conformant flash (16 x 16) Size: 32 MB in 256 Sectors
AMD Standard command set, Manufacturer ID: 0x01, Device ID: 0x227E2301
Erase timeout: 16384 ms, write timeout: 2 ms
Buffer write timeout: 5 ms, buffer size: 32 bytes
[...]
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Mike Frysinger [Sun, 10 Apr 2011 20:06:29 +0000 (16:06 -0400)]
cfi_flash: reverse geometry for M29W800DT parts
The M29W800DT parts also report their geometry with the sector layout
reversed. So add that ID to the flash_fixup_stm function.
Otherwise, we get:
bfin> flinfo
Bank # 1: CFI conformant FLASH (16 x 16) Size: 1 MB in 19 Sectors
AMD Standard command set, Manufacturer ID: 0x20, Device ID: 0x22D7
Erase timeout: 8192 ms, write timeout: 1 ms
Sector Start Addresses:
20000000 20004000 20006000 20008000 20010000
20020000 20030000 20040000 20050000 20060000
20070000 20080000 20090000 200A0000 200B0000
200C0000 200D0000 200E0000 200F0000
Reported-by: Jianxi Fu <fujianxi@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Stefan Roese <sr@denx.de>
Dirk Eibach [Wed, 6 Apr 2011 11:53:50 +0000 (13:53 +0200)]
ppc4xx: Do not stop booting on any keypress on dlvision-10g
Use CONFIG_AUTOBOOT_KEYED on dlvision-10g so that booting can only be
stopped with well defined keypresses.
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Dirk Eibach [Wed, 6 Apr 2011 11:53:49 +0000 (13:53 +0200)]
ppc4xx: Improve fan PWM curve on DLVision 10G
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Dirk Eibach [Wed, 6 Apr 2011 11:53:48 +0000 (13:53 +0200)]
ppc4xx: Enable MPC92469AC on DLVision 10G
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Dirk Eibach [Wed, 6 Apr 2011 11:53:47 +0000 (13:53 +0200)]
ppc4xx: Set DLVision 10G osd position to linux defaults
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Dirk Eibach [Wed, 6 Apr 2011 11:53:46 +0000 (13:53 +0200)]
ppc4xx: Adapt DLVision 10G to new FPGA firmware
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Dirk Eibach [Mon, 18 Apr 2011 08:42:19 +0000 (10:42 +0200)]
ppc4xx: Enable LM64 on DLVision 10G
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Dirk Eibach [Wed, 6 Apr 2011 11:53:44 +0000 (13:53 +0200)]
ppc4xx: Improve video board detection
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Dirk Eibach [Wed, 6 Apr 2011 11:53:43 +0000 (13:53 +0200)]
ppc4xx: Improve DLVision-10G PLL setup
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Ricardo Ribalda Delgado [Wed, 12 Jan 2011 09:14:42 +0000 (10:14 +0100)]
xilinx_ppc_boards: Change address of RESET_VECTOR
Old address of RESET_VECTOR were overwritten by the bss sector, making
impossible its run from xmd.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Jon Povey [Fri, 11 Mar 2011 05:10:56 +0000 (14:10 +0900)]
tools/env: fix redundant env flag comparison
This fixes two bugs with comparison of redundant environment flags on
read.
flag0 and flag1 in fw_env_open() were declared signed instead of
unsigned char breaking BOOLEAN mode "== 0xFF" tests and in INCREMENTAL
mode the wrong environment would be chosen where the flag values are
127 and 128 (either way round). With both flags over 128, both signs
flipped and the logic worked by happy accident.
Also there was a logic bug in the INCREMENTAL test (after signedness was
fixed) in the case flag0=0, flag1=255, env 1 would be incorrectly chosen.
Fix both of these.
Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
Wolfgang Denk [Wed, 20 Apr 2011 21:01:52 +0000 (23:01 +0200)]
Merge branch 'phylib' of git://git.denx.de/u-boot-mmc
Wolfgang Denk [Wed, 20 Apr 2011 20:57:35 +0000 (22:57 +0200)]
Merge branch 'misc' of git://git.denx.de/u-boot-blackfin
Wolfgang Denk [Wed, 20 Apr 2011 20:53:34 +0000 (22:53 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-fdt
Wolfgang Denk [Wed, 20 Apr 2011 20:50:22 +0000 (22:50 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-nand-flash
Wolfgang Denk [Wed, 20 Apr 2011 20:48:47 +0000 (22:48 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-i2c
Wolfgang Denk [Wed, 20 Apr 2011 20:18:13 +0000 (22:18 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-mmc
Wolfgang Denk [Wed, 20 Apr 2011 20:11:21 +0000 (22:11 +0200)]
Revert "PowerPC: Add support for -msingle-pic-base"
This reverts commit
39768f7715ed637ef02f49fc7de664cc1aaf14b3.
Reson: it breaks a number of boards with embedded environment as the
code size grows in some places.
Andy Fleming [Mon, 21 Mar 2011 23:03:22 +0000 (18:03 -0500)]
Add mdio command for new PHY infrastructure
The new mdio command doesn't have all of the features of the mii
command, but it provides the necessary read/write primitives, and allows
users to interact with 10G PHYs, and other PHYs which use Clause 45 of
802.3. This means that the mdio command requires a "Device Address"
argument, though for clause 22 PHYs, the argument can be "-".
Signed-off-by: Andy Fleming <afleming@freescale.com>
Acked-by: Detlev Zundel <dzu@denx.de>
Andy Fleming [Wed, 13 Apr 2011 05:37:12 +0000 (00:37 -0500)]
fsl: Change fsl_phy_enet_if to phy_interface_t
The fsl_phy_enet_if enum was, essentially, the phy_interface_t enum.
This meant that drivers which used fsl_phy_enet_if to deal with
PHY interfaces would have to convert between the two (or we would have
to have them mirror each other, and deal with the ensuing maintenance
headache). Instead, we switch all clients of fsl_phy_enet_if over to
phy_interface_t, which should become the standard, anyway.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Acked-by: Detlev Zundel <dzu@denx.de>
Andy Fleming [Fri, 8 Apr 2011 07:10:54 +0000 (02:10 -0500)]
tsec: Convert tsec to use PHY Lib
This converts tsec to use the new PHY Lib. All of the old PHY support
is ripped out. The old MDIO driver is split off, and placed in
fsl_mdio.c. The initialization is modified to initialize the MDIO
driver as well. The powerpc config file is modified to configure PHYLIB
if TSEC_ENET is configured.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Detlev Zundel <dzu@denx.de>
Andy Fleming [Fri, 8 Apr 2011 02:56:05 +0000 (21:56 -0500)]
phylib: Add a bunch of PHY drivers from tsec
The tsec driver had a bunch of PHY drivers already written. This
converts them all into PHY Lib drivers, and serves as the first
set of PHY drivers for PHY Lib.
While doing that, cleaned up a number of magic numbers (though
not all of them, as PHY vendors like to keep their numbers as
magical as possible). Also, noticed that almost all of the
vitesse/cicada PHYs had the same config/parse/startup functions,
so those have been collapsed into one.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Detlev Zundel <dzu@denx.de>
Andy Fleming [Fri, 8 Apr 2011 07:10:27 +0000 (02:10 -0500)]
Create PHY Lib for U-Boot
Extends the mii_dev structure to participate in a full-blown MDIO and
PHY driver scheme. The mii_dev structure and miiphy calls are modified
in such a way to allow the original mii command and miiphy
infrastructure to work as before, but also to support a new set of APIs
which allow (among other things) sharing of PHY driver code and 10G support
The mii command will continue to support normal PHY management functions
(Clause 22 of 802.3), but will not be changed to support 10G
(Clause 45).
The basic design is similar to PHY Lib from Linux, but simplified for
U-Boot's network and driver infrastructure.
We now have MDIO drivers and PHY drivers
An MDIO driver provides:
read
write
reset
A PHY driver provides:
(optionally): probe
config - initial setup, starting of auto-negotiation
startup - waiting for AN, and reading link state
shutdown - any cleanup needed
The ethernet drivers interact with the PHY Lib using these functions:
phy_connect()
phy_config()
phy_startup()
phy_shutdown()
Each PHY driver can be configured separately, or all at once using
config_phylib_all_drivers.h (added in the patch which adds the drivers)
We also provide generic drivers for Clause 22 (10/100/1000), and
Clause 45 (10G) PHYs.
We also implement phy_reset(), and call it in phy_connect(). Because
phy_reset() is essentially the same as miiphy_reset, but:
a) must support 10G PHYs, and
b) should use the phylib primitives,
we implement miiphy_reset, using phy_reset(), but only when
CONFIG_PHYLIB is set. Otherwise, we just use the old version. In this
way, we save on compile size, even if we don't manage to save code size.
Pulled ethtool.h and mdio.h from:
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6
782d640afd15af7a1faf01cfe566ca4ac511319d
With many, many deletions so as to enable compilation under u-boot
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Detlev Zundel <dzu@denx.de>
Joakim Tjernlund [Wed, 20 Apr 2011 12:22:59 +0000 (14:22 +0200)]
powerpc, 8xx: Fixup all 8xx u-boot.lds scripts
8xx was left behind when fixing up powerpc linking
scripts to support -fpic.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Andy Fleming [Thu, 7 Apr 2011 19:38:35 +0000 (14:38 -0500)]
miiphy: Fix some formatting issues
Mostly putting a space between function name and "(", and
doing return (foo)
Signed-off-by: Andy Fleming <afleming@freescale.com>
Acked-by: Detlev Zundel <dzu@denx.de>
Andy Fleming [Wed, 23 Mar 2011 03:49:13 +0000 (22:49 -0500)]
Remove instances of phy_read/write
There were a few files which were already using phy_read and phy_write
for their PHY function names. It's only a few places, and the name
seems most appropriate for the high-level abstraction, so let's
rename the other versions to something more specific.
Also, uec_phy.c had a marvell_init function which I renamed to not
conflict with the one in marvell.c
Lastly, uec_phy.c was putting a space between the phy writing
function names, and the open paren, so I fixed that
Signed-off-by: Andy Fleming <afleming@freescale.com>
Acked-by: Detlev Zundel <dzu@denx.de>
Mingkai Hu [Thu, 27 Jan 2011 04:52:46 +0000 (12:52 +0800)]
tsec: arrange the code to avoid useless function declaration
This is merely a rearrangement. No changes to the code, except
to remove now-useless declarations.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Detlev Zundel <dzu@denx.de>
Mingkai Hu [Thu, 27 Jan 2011 04:52:45 +0000 (12:52 +0800)]
tsec: use IO accessors for IO accesses
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Detlev Zundel <dzu@denx.de>
Kyle Moffett [Wed, 23 Feb 2011 06:18:24 +0000 (06:18 +0000)]
fdt_support: Fix buffer overflow in fdt_fixup_memory_banks
When fdt_fixup_memory_banks is called with 2-cell address and size
fields in the device-tree (IE: 64-bit address and size), then it will
overflow its on-stack "tmp" buffer.
This fixes the buffer size and adds a comment explaining how many bytes
need to be allocated per record.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Cc: Jerry Van Baren <vanbaren@cideas.com>
Acked-by: Gerald Van Baren <vanbaren@cideas.com>
Dipen Dudhat [Sat, 9 Apr 2011 17:52:32 +0000 (12:52 -0500)]
powerpc/85xx: Modify NAND loader makefiles to compile NAND_SPL linker script
Modify eLBC based platform's NAND loader Makefile to preprocess nand loader
linker script and then use it.
Signed-off-by: Dipen Dudhat <Dipen.Dudhat@freescale.com>
CC: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Alex Waterman [Wed, 6 Apr 2011 20:01:52 +0000 (16:01 -0400)]
nand_spl: Fix large page nand_command()
This patch changes the large page nand_command() routine to use a word
offset instead of a byte offset. The 'offs' argument gets divided by 2
so that the offset passed to nand_command() is still by byte offset.
Originally, the offset was not shifted and when too high an offset was
requested the nand chip would attempt to read non-existent data.
Signed-off-by: Alex Waterman <awaterman@dawning.com>
Matthew McClintock [Tue, 5 Apr 2011 19:39:34 +0000 (14:39 -0500)]
nand/spl: Assuming a static nand page size to reduce code size
Change variables to const to reduce code size, these values are
hardcoded via defines anyways so we might as well assume they
are constants
Signed-off-by: Matthew McClintock <msm@freescale.com>
cc: Scott Wood <scottwood@freescale.com>
Florian Fainelli [Sun, 3 Apr 2011 16:23:56 +0000 (18:23 +0200)]
NAND: rearrange ONFI revision checking, add ONFI 2.3
This patch sync with Brian's patch on Linux in nand_flash_detect_onfi()
commit
b7b1a29d94c17e4341856381bccb4d17495bea60
Author: Brian Norris <computersforpeace@gmail.com>
Date: Sun Dec 12 00:23:33 2010 -0800
mtd: nand: rearrange ONFI revision checking, add ONFI 2.3
In checking for the ONFI revision, the first conditional (for checking
"unsupported" ONFI) seems unnecessary. All ONFI revisions should be
backwards-compatible; even if this is not the case on some newer ONFI
revision, it should simply fail the second version-checking if-else block
(i.e., the bit-fields for 1.0, 2.0, etc. would not be set to 1). Thus, we
move our "unsupported" condition after having checked each bit field.
Also, it's simple enough to add a condition for ONFI revision 2.3. Note
that this does *NOT* mean we handle all new features of ONFI versions
above 1.0.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Florian Fainelli <ffainelli@freebox.fr>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Florian Fainelli [Sun, 3 Apr 2011 16:23:52 +0000 (18:23 +0200)]
NAND: Fix integer overflow in ONFI detection of chips >= 4GiB
This patch sync with David's patch on Linux in nand_flash_detect_onfi()
commit
4ccb3b4497ce01fab4933704fe21581e30fda1a5
Author: David Woodhouse <David.Woodhouse@intel.com>
Date: Fri Dec 3 16:36:34 2010 +0000
mtd: nand: Fix integer overflow in ONFI detection of chips >= 4GiB
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Nick Thompson [Mon, 11 Apr 2011 22:37:41 +0000 (22:37 +0000)]
I2C: OMAP: detect more devices when probing an i2c bus
The omap24xx driver only seems to support devices that have a single subaddress
byte. With these types of devices, the first access in a bus transaction is
usually a write (writes the subaddress) followed by either a read or write to
access the devices registers.
Many such devices will respond to a read as the first access, but there are at
least some that will NACK such a read. (e.g. ADV7180.)
The probe function attempts to detect a devices ACK to a read access only and
fails to find devices that NACK a read.
This commit modifies the probe function to start a write instead. This detects
devices that respond to reads (since they must also respond to writes) as well
as those that only respond to writes. The bus is immediately set to idle after a
(N)ACK avoiding actually writing anything to the device.
Signed-off-by: Nick Thompson <nick.thompson@ge.com>
Fabio Estevam [Mon, 21 Feb 2011 18:02:07 +0000 (15:02 -0300)]
MAINTAINERS: fix email address case
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Simon Glass [Wed, 2 Feb 2011 23:03:28 +0000 (15:03 -0800)]
Fix bad padding of bootp request packet
This seems to pad to one byte longer than required
Signed-off-by: Simon Glass <sjg@chromium.org>
Wolfgang Denk [Wed, 13 Apr 2011 20:04:11 +0000 (22:04 +0200)]
Merge branch 'sf' of git://git.denx.de/u-boot-blackfin
Mike Frysinger [Tue, 12 Apr 2011 07:02:11 +0000 (03:02 -0400)]
gpio: check request result
Make sure the pin request passed before attempting to use it later on.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Fri, 8 Apr 2011 04:39:46 +0000 (00:39 -0400)]
config_defaults.h: drop OSE bootm default
Most arches don't support OSE, and this is a new bootm target, so the
likelihood of any board actually wanting this today is fairly low.
Any board who actually wants this can enable it in the board-specific
config without making it a default bloat.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Sun, 3 Apr 2011 08:40:46 +0000 (04:40 -0400)]
gpio: generalize for all generic gpio providers
The Blackfin gpio command isn't terribly Blackfin-specific. So generalize
the few pieces into two new optional helpers:
name_to_gpio() - turn a string name into a GPIO #
gpio_status() - display current pin bindings (think /proc/gpio)
Once these pieces are pulled out, we can relocate the cmd_gpio.c into the
common directory.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Sun, 3 Apr 2011 01:40:19 +0000 (21:40 -0400)]
md5sum/sha1sum/unzip: split out of mondo mem file
There's no real need to keep these functions in the cmd_mem file since
they do not use any of the common global mem variables. So split them
out into their own dedicated cmd files.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Tue, 21 Dec 2010 19:19:51 +0000 (14:19 -0500)]
crc32: make command optional
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Mon, 27 Dec 2010 04:32:22 +0000 (23:32 -0500)]
make `go` optional
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Mon, 27 Dec 2010 04:09:45 +0000 (23:09 -0500)]
env: make import/export optional
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Wolfgang Denk [Wed, 13 Apr 2011 19:53:09 +0000 (21:53 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-x86
Peter Tyser [Wed, 13 Apr 2011 16:46:56 +0000 (11:46 -0500)]
cfi_flash: Fix CONFIG_SYS_FLASH_AUTOPROTECT_LIST usage
Commit
6ee1416e8184b4d9ebe6087d396a60bcecf3551c (mtd, cfi: introduce
void flash_protect_default(void)) introduced a bug which resulted in
boards that define CONFIG_SYS_FLASH_AUTOPROTECT_LIST not compiling with
the the following errors and warning:
ptyser@petert u-boot $ make -s xpedite520x
Configuring for xpedite520x board...
cfi_flash.c: In function 'flash_protect_default':
cfi_flash.c:2118: error: 'i' undeclared (first use in this function)
cfi_flash.c:2118: error: (Each undeclared identifier is reported only once
cfi_flash.c:2118: error: for each function it appears in.)
cfi_flash.c:2118: error: 'apl' undeclared (first use in this function)
cfi_flash.c:2118: error: invalid application of 'sizeof' to incomplete type 'struct apl_s'
cfi_flash.c: In function 'flash_init':
cfi_flash.c:2137: warning: unused variable 'apl'
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Reported-by: Kumar Gala <galak@kernel.crashing.org>
Cc: Heiko Schocher <hs@denx.de>
James Kosin [Wed, 13 Apr 2011 19:12:18 +0000 (15:12 -0400)]
sf: sst: add support for SST25VF064C
Signed-off-by: James Kosin <jkosin@intcomgrp.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Raffaele Recalcati [Wed, 23 Mar 2011 04:06:50 +0000 (04:06 +0000)]
MMC may wrongly regconize 2GB eMMC as high capacity
Hi Terry,
> So I guess:
> mmc_init calls mmc_send_op_cond that set high_capacity,
> than it calls mmc_startup, that, with MMC_CMD_SEND_CSD command, set
> the capacity, using values in CSD register.
> So I guess that mmc_change_freq should not recalculate high_capacity.
>
> It seems better, isn't it?
>
> Regards,
> Raffaele
>
Finally I think that it is enough to apply the following patch in order
to fix the issue.
Regards,
Raffaele
Signed-off-by: Andy Fleming <afleming@freescale.com>
Raffaele Recalcati [Fri, 11 Mar 2011 02:01:14 +0000 (02:01 +0000)]
mmc: trace added
Defining CONFIG_MMC_TRACE in the include board file it is possible to activate
a tracing support.
This code helps in case of eMMC hw failure or to investigate possible eMMC
initialization issues.
Signed-off-by: Raffaele Recalcati <raffaele.recalcati@bticino.it>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Raffaele Recalcati [Fri, 11 Mar 2011 02:01:13 +0000 (02:01 +0000)]
mmc: SEND_OP_COND considers card capabilities (voltage)
The first SEND_OP_COND (CMD1) command added is used to ask card capabilities.
After it an AND operation is done between card capabilities and host
capabilities (at the moment only for the voltage field).
Finally the correct value is sent to the MMC, waiting that the card
exits from busy state.
Signed-off-by: Raffaele Recalcati <raffaele.recalcati@bticino.it>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Raffaele Recalcati [Fri, 11 Mar 2011 02:01:12 +0000 (02:01 +0000)]
mmc: checking status after commands with R1b response
It is recommended to check card status after these kind of commands.
This is done using CMD13 (SEND_STATUS) JEDEC command until
the card is ready.
In case of error the card status field is displayed.
Signed-off-by: Raffaele Recalcati <raffaele.recalcati@bticino.it>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Minkyu Kang [Tue, 4 Jan 2011 01:04:56 +0000 (01:04 +0000)]
mmc: remove duplicated header file
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Minkyu Kang [Tue, 4 Jan 2011 01:04:19 +0000 (01:04 +0000)]
mmc: show mmc capacity using print_size
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Thomas Chou [Fri, 24 Dec 2010 13:12:21 +0000 (13:12 +0000)]
mmc: add generic mmc spi driver
This patch supports mmc/sd card with spi interface. It is based on
the generic mmc framework. It works with SDHC and supports multi
blocks read/write.
The crc checksum on data packet is enabled with the def,
There is a subcomamnd "mmc_spi" to setup spi bus and cs at run time.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Mike Frysinger [Wed, 20 Oct 2010 01:15:53 +0000 (01:15 +0000)]
mmc: constify & localize data
These local vars need not be writable nor exported.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Frans Meulenbroeks [Sat, 31 Jul 2010 04:45:18 +0000 (04:45 +0000)]
drivers/mmc/fsl_esdhc.c: reordered tests
As DATA_ERROR includes the value IRQSTAT_DTOE, a timeout error
would yield the first error return instead of TIMEOUT.
By swapping the test TIMEOUTs are reported as such
An alternate solution would be to remove the IRQSTAT_DTOE from the DATA_ERROR define
but as that one might be less desired I've opted for the simplest solution
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Wolfgang Wegner [Fri, 23 Apr 2010 05:43:12 +0000 (05:43 +0000)]
add CONFIG_SPI_IDLE_VAL for cf_spi.c to allow use of spi_mmc
This patch adds CONFIG_SPI_IDLE_VAL to cf_spi.c
The default setting is 0x0 to behave same as current version, in case
CONFIG_SPI_MMC is set, the value is set to 0xFFFF (all ones). In either
case, the value can be overwritten by board configuration.
Signed-off-by: Wolfgang Wegner <w.wegner@astro-kom.de>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Matt Waddel [Thu, 24 Feb 2011 16:35:23 +0000 (16:35 +0000)]
MMC: Max blocks value adjustable
The maximum blocks value was hardcoded to 65535 due to a 16 bit
register length. The value can change for different platforms.
This patch makes the default the current value of 65535, but it
is configurable for other platforms.
Signed-off-by: Matt Waddel <matt.waddel@linaro.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Graeme Russ [Wed, 13 Apr 2011 09:56:23 +0000 (19:56 +1000)]
Merge branch 'master' of git://git.denx.de/u-boot-x86
Graeme Russ [Wed, 13 Apr 2011 09:43:30 +0000 (19:43 +1000)]
x86: Update MAINTAINERS and delete README files
The README files are totally out-of-date to the point where they do more
harm than good
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
projects / project / bcm63xx / u-boot.git / log