rt2x00: rt2800lib: introduce RFCSR3_VCOCAL_EN

On the RF3290,RF5360,RF5370,RF5372,RF5390,RF5392
radio frontends, the VCO calibration can be
controlled via the RFCSR3 register. The current
code uses the RFCSR30_RF_CALIBRATION constant to
enable the calibration, however that belongs to
the RFCSR30 register. Although the values of the
constant is correct, but using that for another
register is confusing.

Add a new definition for the VCO calibration enable
bit of the RFCSR3 register and use that in the
relevant places in order to avoid confusions.

The patch contains no functional changes.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: rt2800lib: remove trailing semicolons from RFCSR3_* defines

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

carl9170: fix signal strength reporting issues

On A-MPDU frames, the hardware only reports valid
signal strength data for the last subframe.

This patch fixes it by flagging everything but the
last subframe in an A-MPDU to tell mac80211 to
ignore the signal strength entirely. Otherwise
the empty value (= 0 dbm) will distort the
average quite badly.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: rt2800lib: fix indentation in rt2800_init_rfcsr

The patch contains no functional changes.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: rt2800lib: fix indentation of some rt2x00_rt calls

The patch contains no functional changes.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

p54: potential signedness issue in p54_parse_rssical()

"entries" is unsigned here, so it is never less than zero.  In theory,
len could be less than offset so I have added a check for that.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'for-upstream' of git://git./linux/kernel/git/bluetooth/bluetooth-next

Revert "Bluetooth: Fix possible deadlock in SCO code"

This reverts commit 269c4845d5b3627b95b1934107251bacbe99bb68.

The commit was causing dead locks and NULL dereferences in the sco code:

 [28084.104013] BUG: soft lockup - CPU#0 stuck for 22s! [kworker/u:0H:7]
 [28084.104021] Modules linked in: btusb bluetooth <snip [last unloaded:
bluetooth]
...
 [28084.104021]  [<c160246d>] _raw_spin_lock+0xd/0x10
 [28084.104021]  [<f920e708>] sco_conn_del+0x58/0x1b0 [bluetooth]
 [28084.104021]  [<f920f1a9>] sco_connect_cfm+0xb9/0x2b0 [bluetooth]
 [28084.104021]  [<f91ef289>]
hci_sync_conn_complete_evt.isra.94+0x1c9/0x260 [bluetooth]
 [28084.104021]  [<f91f1a8d>] hci_event_packet+0x74d/0x2b40 [bluetooth]
 [28084.104021]  [<c1501abd>] ? __kfree_skb+0x3d/0x90
 [28084.104021]  [<c1501b46>] ? kfree_skb+0x36/0x90
 [28084.104021]  [<f91fcb4e>] ? hci_send_to_monitor+0x10e/0x190 [bluetooth]
 [28084.104021]  [<f91fcb4e>] ? hci_send_to_monitor+0x10e/0x190 [bluetooth]

Cc: stable@vger.kernel.org
Reported-by: Chan-yeol Park <chanyeol.park@gmail.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: trivial: Change NO_FCS_RECV to RECV_NO_FCS

Make code more readable by changing CONF_NO_FCS_RECV which is read
as "No L2CAP FCS option received" to CONF_RECV_NO_FCS which means
"Received L2CAP option NO_FCS". This flag really means that we have
received L2CAP FRAME CHECK SEQUENCE (FCS) OPTION with value "No FCS".

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Process receiving FCS_NONE in L2CAP Conf Rsp

Process L2CAP Config rsp Pending with FCS Option 0x00 (No FCS)
which is sent by Motorola Windows 7 Bluetooth stack. The trace
is shown below (all other options are skipped).

...
< ACL data: handle 1 flags 0x00 dlen 48
    L2CAP(s): Config req: dcid 0x0043 flags 0x00 clen 36
      ...
      FCS Option 0x00 (No FCS)
> ACL data: handle 1 flags 0x02 dlen 48
    L2CAP(s): Config req: dcid 0x0041 flags 0x00 clen 36
      ...
      FCS Option 0x01 (CRC16 Check)
< ACL data: handle 1 flags 0x00 dlen 47
    L2CAP(s): Config rsp: scid 0x0043 flags 0x00 result 4 clen 33
      Pending
      ...
> ACL data: handle 1 flags 0x02 dlen 50
    L2CAP(s): Config rsp: scid 0x0041 flags 0x00 result 4 clen 36
      Pending
      ...
      FCS Option 0x00 (No FCS)
< ACL data: handle 1 flags 0x00 dlen 14
    L2CAP(s): Config rsp: scid 0x0043 flags 0x00 result 0 clen 0
      Success
> ACL data: handle 1 flags 0x02 dlen 14
    L2CAP(s): Config rsp: scid 0x0041 flags 0x00 result 0 clen 0
      Success
...

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Fix missing L2CAP EWS Conf parameter

If L2CAP_FEAT_FCS is not supported we sould miss EWS option
configuration because of break. Make code more readable by
combining FCS configuration in the single block.

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: AMP: Check that AMP is present and active

Before starting quering remote AMP controllers make sure
that there is local active AMP controller.

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: AMP: Mark controller radio powered down after HCIDEVDOWN

After getting HCIDEVDOWN controller did not mark itself as 0x00 which
means: "The Controller radio is available but is currently physically
powered down". The result was even if the hdev was down we return
in controller list value 0x01 "status 0x01 (Bluetooth only)".

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Refactor l2cap_send_disconn_req

l2cap_send_disconn_req takes 3 parameters of which conn might be
derived from chan. Make this conversion inside l2cap_send_disconn_req.

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Move double negation to macros

Some comparisons needs to double negation(!!) in order to make the value
of the field boolean. Add it to the macro makes the code more readable.

Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Implement deferred sco socket setup

In order to authenticate and configure an incoming SCO connection, the
BT_DEFER_SETUP option was added. This option is intended to defer reply
to Connect Request on SCO sockets.
When a connection is requested, the listening socket is unblocked but
the effective connection setup happens only on first recv. Any send
between accept and recv fails with -ENOTCONN.

Signed-off-by: Frédéric Dalleau <frederic.dalleau@linux.intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Add BT_DEFER_SETUP option to sco socket

This option will set the BT_SK_DEFER_SETUP bit in socket flags.

Signed-off-by: Frédéric Dalleau <frederic.dalleau@linux.intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: cancel power_on work when unregistering the device

We need to cancel the hci_power_on work in order to avoid it run when we
try to free the hdev.

[ 1434.201149] ------------[ cut here ]------------
[ 1434.204998] WARNING: at lib/debugobjects.c:261 debug_print_object+0x8e/0xb0()
[ 1434.208324] ODEBUG: free active (active state 0) object type: work_struct hint: hci
_power_on+0x0/0x90
[ 1434.210386] Pid: 8564, comm: trinity-child25 Tainted: G        W    3.7.0-rc5-next-
20121112-sasha-00018-g2f4ce0e #127
[ 1434.210760] Call Trace:
[ 1434.210760]  [<ffffffff819f3d6e>] ? debug_print_object+0x8e/0xb0
[ 1434.210760]  [<ffffffff8110b887>] warn_slowpath_common+0x87/0xb0
[ 1434.210760]  [<ffffffff8110b911>] warn_slowpath_fmt+0x41/0x50
[ 1434.210760]  [<ffffffff819f3d6e>] debug_print_object+0x8e/0xb0
[ 1434.210760]  [<ffffffff8376b750>] ? hci_dev_open+0x310/0x310
[ 1434.210760]  [<ffffffff83bf94e5>] ? _raw_spin_unlock_irqrestore+0x55/0xa0
[ 1434.210760]  [<ffffffff819f3ee5>] __debug_check_no_obj_freed+0xa5/0x230
[ 1434.210760]  [<ffffffff83785db0>] ? bt_host_release+0x10/0x20
[ 1434.210760]  [<ffffffff819f4d15>] debug_check_no_obj_freed+0x15/0x20
[ 1434.210760]  [<ffffffff8125eee7>] kfree+0x227/0x330
[ 1434.210760]  [<ffffffff83785db0>] bt_host_release+0x10/0x20
[ 1434.210760]  [<ffffffff81e539e5>] device_release+0x65/0xc0
[ 1434.210760]  [<ffffffff819d3975>] kobject_cleanup+0x145/0x190
[ 1434.210760]  [<ffffffff819d39cd>] kobject_release+0xd/0x10
[ 1434.210760]  [<ffffffff819d33cc>] kobject_put+0x4c/0x60
[ 1434.210760]  [<ffffffff81e548b2>] put_device+0x12/0x20
[ 1434.210760]  [<ffffffff8376a334>] hci_free_dev+0x24/0x30
[ 1434.210760]  [<ffffffff82fd8fe1>] vhci_release+0x31/0x60
[ 1434.210760]  [<ffffffff8127be12>] __fput+0x122/0x250
[ 1434.210760]  [<ffffffff811cab0d>] ? rcu_user_exit+0x9d/0xd0
[ 1434.210760]  [<ffffffff8127bf49>] ____fput+0x9/0x10
[ 1434.210760]  [<ffffffff81133402>] task_work_run+0xb2/0xf0
[ 1434.210760]  [<ffffffff8106cfa7>] do_notify_resume+0x77/0xa0
[ 1434.210760]  [<ffffffff83bfb0ea>] int_signal+0x12/0x17
[ 1434.210760] ---[ end trace a6d57fefbc8a8cc7 ]---

Cc: stable@vger.kernel.org
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Add missing lock nesting notation

This patch fixes the following report, it happens when accepting rfcomm
connections:

[  228.165378] =============================================
[  228.165378] [ INFO: possible recursive locking detected ]
[  228.165378] 3.7.0-rc1-00536-gc1d5dc4 #120 Tainted: G        W
[  228.165378] ---------------------------------------------
[  228.165378] bluetoothd/1341 is trying to acquire lock:
[  228.165378]  (sk_lock-AF_BLUETOOTH-BTPROTO_RFCOMM){+.+...}, at:
[<ffffffffa0000aa0>] bt_accept_dequeue+0xa0/0x180 [bluetooth]
[  228.165378]
[  228.165378] but task is already holding lock:
[  228.165378]  (sk_lock-AF_BLUETOOTH-BTPROTO_RFCOMM){+.+...}, at:
[<ffffffffa0205118>] rfcomm_sock_accept+0x58/0x2d0 [rfcomm]
[  228.165378]
[  228.165378] other info that might help us debug this:
[  228.165378]  Possible unsafe locking scenario:
[  228.165378]
[  228.165378]        CPU0
[  228.165378]        ----
[  228.165378]   lock(sk_lock-AF_BLUETOOTH-BTPROTO_RFCOMM);
[  228.165378]   lock(sk_lock-AF_BLUETOOTH-BTPROTO_RFCOMM);
[  228.165378]
[  228.165378]  *** DEADLOCK ***
[  228.165378]
[  228.165378]  May be due to missing lock nesting notation

Cc: stable@vger.kernel.org
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

brcmsmac: Fix possible NULL pointer dereference in _dma_ctrlflags()

There's a debug message to warn if this function is passed a NULL
pointer, but in order to print the message we have to dereference the
pointer. Obviously this isn't a good idea, so remove the message.

Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wireless: mwifiex: Fix typo in wireless/mwifiex driver

Correct spelling typo in wireless/mwifiex driver.

Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: use SIMPLE_DEV_PM_OPS

rtlwifi only provides pm callbacks for functions covered by pm sleep
and they are also just called if CONFIG_PM_SLEEP is set.

Only add functions rtl_pci_suspend and rtl_pci_resume if
CONFIG_PM_SLEEP is set and use SIMPLE_DEV_PM_OPS instead of
manually filling struct dev_pm_ops.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

p54pci: use SIMPLE_DEV_PM_OPS

p54pci does not provide any runtime pm callbacks, so support for
PM_RUNTIME is not needed and we could go to PM_SLEEP.
This also makes it possible to use SIMPLE_DEV_PM_OPS instead of
manually filling struct dev_pm_ops.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: use SIMPLE_DEV_PM_OPS

ath9k does not provide any runtime pm callbacks, so support for
PM_RUNTIME is not needed and we could go to PM_SLEEP.
This also makes it possible to use SIMPLE_DEV_PM_OPS instead of
manually filling struct dev_pm_ops.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8192se: Fixed coding style issues in the driver

This patch fixes almost all coding issues in the rtl8192se driver. Only
exception is putting trailing */ on separate lines.

Signed-off-by: Daniel Stamer <daniel@stamer.info>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: fix struct member mismatch

Using bss->information_elements and treating
bss->len_beacon_ies as its size is wrong, the
real size is len_information_elements.

Found while I was reviewing the use of this
cfg80211 API (as it is actually potentially
broken due to races.)

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: change debug output for received event.

see header.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: fix bug in setting mgmt ie and parsing vndrs ie.

Parsing vndrs ie was not taking len of tlv itself in account. Setting
mgmt ie was missing check for length indicating non configured ie and
wrongly checking available length.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: remove mode from struct brcmf_cfg80211_conf

The mode should be stored and used per virtual interface. Remove
the mode from device global structure and rework the code to use
the mode from brcmf_cfg80211_vif.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: get rid of struct brcmf_cfg80211_info::link_up attribute

This attribute indicates successful IBSS or AP connection has been
established. However, this no longer works for virtual interfaces.
As it turns out this attribute is identical to the CONNECTED bit
in struct brcmf_cfg80211_vif::sme_state. This patch removes the
attribute and rework some functions relying on it.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmsmac: support 4313iPA

Add support for 4313 iPA variant.
It is a variant of already supported 4313 ePA
and needs some PHY changes to work properly.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmsmac: move PHY functions

Move functions in
preparation for 4313iPA changes

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmsmac: hardware info in debugfs

Put basic information about hardware in debugfs.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Acked-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmsmac: fix bounds checking in tx/rx

brcms_b_txstatus and brcms_b_recv are off by one when
doing bounds checking on number of packets to process

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmsmac: cleanup in isr code

brcms_c_isr returns true if interrupt was for us
and if dpc should be scheduled which is the same thing.
Simplify it.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmsmac: handle packet drop during transmit correctly

The .tx() callback function can drop packets when there is no
space in the DMA fifo. Propagate that information to caller
and make sure the freed sk_buff reference is not accessed.

Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: update the MAINTAINERS file

Organizational changes need to be reflected in the MAINTAINERS file.
The contact info on wireless.kernel.org has also been updated.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wireless: allow Atheros card to not depend on ath.ko

There are 2 different things:
- sub-menu for "Atheros Wireless cards" family
- module ath.ko with common Atheros code

Until now, they both used to depend on the same Kconfig variable ATH_COMMON.
Thus, being "Atheros card" and "depending on ath.ko" was the same.

To allow module to belong to the
"Atheros Wireless cards" family but not use ath.ko,
2 conditions above need to be separated.

So, this patch introduce new Kconfig variable ATH_CARDS for belonging
to the "Atheros Wireless Cards" family; while ATH_COMMON becomes hidden
variable to express dependency on common Atheros code in ath.ko. Modules
that depend on this common code now express it by setting ATH_COMMON.

Right now, ath6kl do not depend on common code and thus do not set ATH_COMMON.

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Remove redundant NULL assignment

'bf_next' is cleared using ATH_TXBUF_RESET() in both the
callsites of ath_tx_get_buffer().

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Implement sta_add_debugfs/sta_remove_debugfs

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Replace WME_NUM_TID with IEEE80211_NUM_TIDS

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Move ethtool functions to debug.c

The ethtool statistics are available only when
CONFIG_ATH9K_DEBUGFS is enabled, move these functions
to debug.c

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Use addr_mask to disallow invalid MAC addresses in mutli-bssid mode

Reported-by: Petr Stetiar <ynezz@true.cz>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: advertise GreenField, 40MHz intolerance support to cfg80211

This patch adds support for advertising GreenField, 40MHz intolerance
or LDPC coding support to cfg80211.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Fix buffer overflow error

The commit "ath9k: stomp audio profiles on weak signal
strength" failed to take care of new stomp type while
programming concurrent tx priority. That leads to array
index out of bounds access.

drivers/net/wireless/ath/ath9k/btcoex.c:414
        ath9k_hw_btcoex_set_concur_txprio()
               error: buffer overflow 'stomp_txprio' 4 <= 4

Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ssb: extif: fix compile errors

If CONFIG_SSB_EMBEDDED or CONFIG_SSB_DRIVER_MIPS is set and
CONFIG_SSB_DRIVER_EXTIF is not set, it will cause compile problems
because of missing functions. This patch fixes these problems.

The mips driver now also uses ssb_chipco_available() instead of
checking bus->chipco.dev manually.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

bcma: handle return value of pci_assign_resource

This fixes the following warning:

  CC      drivers/bcma/driver_pci_host.o
drivers/bcma/driver_pci_host.c: In function 'bcma_core_pci_fixup_addresses':
drivers/bcma/driver_pci_host.c:555:23: error: ignoring return value of
'pci_assign_resource', declared with attribute warn_unused_result
[-Werror=unused-result]

Reported-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

bcma: add more package IDs

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

p54: improve TSF timestamp precision

The LMAC API states that the TSF clock value of
every rx'ed frame is a "usec accurate timestamp
of the hardware clock at the end of frame
(before OFDM SIFS EOF padding)".

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: initialize rx_status

The vendor radiotap patch added a few fields to
struct ieee80211_rx_status that need to be zero,
initialize the struct instead of using whatever
was left on the stack.

Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Tested-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlegacy: initialize rx_status

The vendor radiotap patch added a few fields to
struct ieee80211_rx_status that need to be zero,
initialize the struct instead of using whatever
was left on the stack.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmsmac: Add __printf verification to logging prototypes

Adding __printf helps spot format and argument mismatches.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'for-john' of git://git./linux/kernel/git/jberg/mac80211-next

cfg80211: fix some tracing output issues

In some cases, e.g. probe_status, there were spaces
missing so the trace output was confusing. Also make
it more like mac80211 when printing netdevs/wiphys
to make reading a combined log easier.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211_hwsim: remove printing scan config

The frequencies will be printed when actually
doing the scan, and the IEs can be captured
on the hwsim0 monitor.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211_hwsim: advertise VHT support

If the number of channels is > 1, which means that
hwsim will use mac80211 channel contexts, it can
also advertise VHT support.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wireless: add definitions for VHT MCS support

Add definitions for the VHT MCS support values that
are used to indicate, for each number of streams
(1 through 8) which MCSes are supported.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: support VHT rates in TX info

To achieve this, limit the number of retries to
31 (instead of 255) and use the three bits that
are then free for VHT flags.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: support drivers reporting VHT RX

Add support to mac80211 for having drivers report
received VHT MCS information.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

nl80211/cfg80211: add VHT MCS support

Add support for reporting and calculating VHT MCSes.

Note that I'm not completely sure that the bitrate
calculations are correct, nor that they can't be
simplified.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: convert to channel definition struct

Convert mac80211 (and where necessary, some drivers a
little bit) to the new channel definition struct.

This will allow extending mac80211 for VHT, which is
currently restricted to channel contexts since there
are no drivers using that which makes it easier. As
I also don't care about VHT for drivers not using the
channel context API, I won't convert the previous API
to VHT support.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

nl80211/cfg80211: support VHT channel configuration

Change nl80211 to support specifying a VHT (or HT)
using the control channel frequency (as before) and
new attributes for the channel width and first and
second center frequency. The old channel type is of
course still supported for HT.

Also change the cfg80211 channel definition struct
to support these by adding the relevant fields to
it (and removing the _type field.)

This also adds new helper functions:
 - cfg80211_chandef_create to create a channel def
   struct given the control channel and channel type,
 - cfg80211_chandef_identical to check if two channel
   definitions are identical
 - cfg80211_chandef_compatible to check if the given
   channel definitions are compatible, and return the
   wider of the two

This isn't entirely complete, but that doesn't matter
until we have a driver using it. In particular, it's
missing
 - regulatory checks on the usable bandwidth (if that
   even makes sense)
 - regulatory TX power (database can't deal with it)
 - a proper channel compatibility calculation for the
   new channel types

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211: pass a channel definition struct

Instead of passing a channel pointer and channel type
to all functions and driver methods, pass a new channel
definition struct. Right now, this struct contains just
the control channel and channel type, but for VHT this
will change.

Also, add a small inline cfg80211_get_chandef_type() so
that drivers don't need to use the _type field of the
new structure all the time, which will change.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

nl80211: add documentation for channel type

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211: remove remain-on-channel channel type

As mwifiex (and mac80211 in the software case) are the
only drivers actually implementing remain-on-channel
with channel type, userspace can't be relying on it.
This is the case, as it's used only for P2P operations
right now.

Rather than adding a flag to tell userspace whether or
not it can actually rely on it, simplify all the code
by removing the ability to use different channel types.
Leave only the validation of the attribute, so that if
we extend it again later (with the needed capability
flag), it can't break userspace sending invalid data.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: fix managed mode channel flags handling

If ieee80211_prep_channel() decides that HT should be
disabled (because the HT IEs from the AP were invalid)
it will set the IEEE80211_STA_DISABLE_HT to not send
HT capabilities to the AP when associating. If this
happens during authentication, the flag will be lost
and we send HT frames, even if the channel config was
set up for non-HT. This can lead to issues.

Fix this by always resetting the ifmgd flags to zero
when the channel context is released so that the flag
resetting in ieee80211_mgd_assoc() isn't necessary.

To make the code a bit easier move the call to release
the channel in ieee80211_set_disassoc() to the end of
the function together with the flag resetting (which
needs to be at the end to avoid timers setting flags.)

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: remove mesh config macros from mesh_plink.c

Use shortcut pointer instead where it is appropriate.

Signed-off-by: Marco Porsch <marco.porsch@etit.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: refactor ieee80211_set_qos_hdr

Return early if not a QoS Data frame.
Give proper documentation.

Signed-off-by: Marco Porsch <marco.porsch@etit.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: move Mesh Capability field definition to ieee80211.h

Signed-off-by: Marco Porsch <marco.porsch@etit.tu-chemnitz.de>
[prefix with IEEE80211_]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: in ADHOC print debug message for every Auth message

The debug message has to be printed also for an Auth message with
auth_sequence != 1. This helps understanding whether the two Auth
messages are exchanged correctly or not.

Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: in ADHOC don't update last_rx if sta is not authorized

It does not make sense to keep a station alive if it is not authorised
at all. If IBSS/RSN is used it could also be the case that something
went wrong during the keys exchange and the stations ended up in a not
recoverable state.

By not updating last_rx we are giving the station a chance to be
deleted and to start the key exchange once again from scratch.

Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211: change function signature of cfg80211_get_p2p_attr()

The function cfg80211_get_p2p_attr() can fail and returns
a negative error code. However, the return type is unsigned
int. The largest positive number is determined by desired_len
variable in the function, which is u16. So changing the return
type to int to allow easy error checking. Also change the type
for the attribute to enum for improved type checking.

Signed-off-by: Arend van Spriel <arend@broadcom.com>
[fix indentation, don't use u8 attr variable]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211: use DS or HT operation IEs to determine BSS channel

Currently, mac80211 checks the DS params IE if present and
uses it for the (primary) BSS channel, instead of the one
that the frame was received on. This is particularly useful
in the 2.4 GHz band since a frame is often received on one
of the adjacent channels due to overlap.

Move this code to cfg80211 so other drivers also do this.

Additionally, on 5 GHz, in particular with some (possibly)
upcoming changes in 802.11ai and duplicate transmissions
when wider channels are used, something similar happens.
So if present, also use the (primary) channel information
contained in the HT operation IE.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: disable HT advertising unless AP supports it

If the AP doesn't support HT, or more importantly if
it does but we have to disable it because its IEs are
broken, don't advertise HT support in our association
request. Otherwise, we configure our channel to be a
20 MHz non-HT channel but the AP might still think we
support HT, or even 40 MHz.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: rename IEEE80211_STA_DISABLE_11N to HT

Since the 11n spec amendment was rolled into the
2012 version, "11n" no longer makes sense. Use
"HT" instead.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: fix RX chains configuration

If the driver doesn't support 40 MHz channels, then
mac80211 erroneously sets number of RX chains to one
although the number of chains is independent of the
support for 40 MHz channels.

Fix this by checking the 40 MHz support only for the
code that sets the 40 MHz channel not the complete
HT code block.

This also means the HT20 channel type will always be
set in the changed code block so there's no need to
set it in case we override the AP due to invalid IEs
in the probe response/beacon.

The indentation is a bit quirky, but I'm rewriting
this code for VHT support so this will change again
very soon.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: fix radiotap vendor area skipping

The radiotap vendor area in the skb head must be skipped
and accounted for in a few functions until it is removed.
I missed this in my patch, so a few places use this data
as though it was the 802.11 header, fix these places.

Reported-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Tested-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

rtl8723ae: fix build break from "mac80211: support RX_FLAG_MACTIME_END"

  CC      drivers/net/wireless/rtlwifi/rtl8723ae/trx.o
drivers/net/wireless/rtlwifi/rtl8723ae/trx.c: In function ‘rtl8723ae_rx_query_desc’:
drivers/net/wireless/rtlwifi/rtl8723ae/trx.c:324:21: error: ‘RX_FLAG_MACTIME_MPDU’ undeclared (first use in this function)
drivers/net/wireless/rtlwifi/rtl8723ae/trx.c:324:21: note: each undeclared identifier is reported only once for each function it appears in
make[3]: *** [drivers/net/wireless/rtlwifi/rtl8723ae/trx.o] Error 1

Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'for-john' of git://git./linux/kernel/git/jberg/mac80211-next

Merge branch 'for-john' of git://git./linux/kernel/git/iwlwifi/iwlwifi-next

Conflicts:
drivers/net/wireless/iwlwifi/pcie/trans.c

brcmsmac: Remove stray argument from debug macro

One of the debug macro invocations ended up with a stray 0 argument
where the format string should be. Remove it.

Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmsmac: Remove unused wlc_prio2prec_map and _BRCMS_PREC_* constants

Fixes sparse warning:
drivers/net/wireless/brcm80211/brcmsmac/main.c:308:10: sparse: symbol 'wlc_prio2prec_map' was not declared. Should it be static?

Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Remove 'stations' debugfs file

The 'stations' debugfs file has multiple issues. It doesn't scale
to an arbitrary number of associated stations and allocating
64K is not elegant either. Now that changes have been made in
mac80211 to support dynamic creation/deletion of driver-specific
debugfs files on station addition/removal, remove this file and
make use of the mac80211 hooks (which will be done in a sebsequent
patch).

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Fix rate control debugging

Update the rate statistics only when debugfs has been enabled
in ath9k and mac80211 and move the stat() functions under proper
conditionals.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Fill remove_sta_debugfs() callback

Remove the rate control statistics debugfs file properly
via remove_sta_debugfs(). Also, check for both MAC80211_DEBUGFS
and ATH9K_DEBUGFS config options.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Add a debugfs file to dump queue statistics

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Fix the 'xmit' debugfs file

The 'xmit' debugfs file has become big and unwieldy, fix
multiple issues with its usage:

* Store TX counters/statistics only for the 4 Access Categories.
  Use IEEE80211_NUM_ACS instead of ATH9K_NUM_TX_QUEUES.

* Move various utility macros to debug.h, they can be reused
  elsewhere.

* Remove tx_complete_poll_work_seen.

* Remove code that accesses various internal queue-specific
  variables without any locking whatsoever. HW/SW queue details
  will be handled in a subsequent patch.

* Do not print internal values like txq_headidx and txq_headidx.
  They were mostly unused anyway, considering code like:
  PRX("txq_tailidx:     ", txq_headidx);

* Handle 'txprocdesc' for EDMA too.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k/ath9k_htc: Remove WME macros

Use the macros provided by mac80211 and remove redundant
declarations inside the drivers.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

net/wireless: ipw2200: introduce ipw_set_geo function

Move regulatory domain initialization code to a separate function.

Signed-off-by: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: stomp audio profiles on weak signal strength

On lower WLAN signal strength, WLAN downlink traffic might suffer
from retransmissions. At the mean time, playing SCO/A2DP profiles
is affecting WLAN stability. In such scenario, by stomping SCO/A2DP
BT traffic completely for a BTCOEX period, gives WLAN traffic an
oppertunity to recover PHY rate. It also improves WLAN stability at
lower RSSI without sacificing BT traffic.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Fix MCI reset in BT cal_req

This patch reverts the commit "ath9k_hw: Wait BT calibration to complete"
and bail out from MCI interrupt routine for chip reset. The above commit
stalls the WLAN TCP traffic while bringing up and down the BT interface
iteratively. Fixing this properly by queueing up chip reset and bailing
out properly from tasklet routine.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Process FATAL interrupts at first

FATAL and WATCHDOG interrupts should be processed first followed
by others.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'for-upstream' of git://git./linux/kernel/git/bluetooth/bluetooth-next

Merge branch 'master' of git://git./linux/kernel/git/linville/wireless

Conflicts:
drivers/net/wireless/brcm80211/brcmfmac/wl_cfg80211.c
drivers/net/wireless/iwlwifi/pcie/tx.c

mac80211: Add debugfs callbacks for station addition/removal

Provide drivers with hooks to create debugfs files when
a new station is added. This would help drivers to take
advantage of mac80211's station list infrastructure and not maintain
tedious station management code internally.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
[ifdef inline wrapper functions]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

iwlwifi: remove effectless assignment

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

brcmfmac: include linux/vmalloc.h from usb.c

This avoids build failures on some architectures...

Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Arend van Spriel <arend@broadcom.com>

brcmfmac: check return from kzalloc in brcmf_fweh_process_event

Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Arend van Spriel <arend@broadcom.com>

brcmsmac: Remove some noisy and uninformative debug messages

These messages clutter up the trace buffer without adding any useful
information.

Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Tested-by: Daniel Wagner <wagi@monom.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmsmac: Add tracepoint for AMPDU session information

Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Tested-by: Daniel Wagner <wagi@monom.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>