git.openwrt.org Git - openwrt/staging/blogic.git/log

drm/i915/icl: Handle hotplug interrupts for DP over TBT

This patch enables hotplug interrupts for DP over TBT output on TC
ports. The TBT interrupts are enabled and handled irrespective of the
actual output type which could be DP Alternate, DP over TBT, native DP
or native HDMI.

Cc: Animesh Manna <animesh.manna@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180616000530.5357-3-paulo.r.zanoni@intel.com

drm/i915/icl: Support for TC North Display interrupts

The hotplug interrupts for the ports can be routed to either North
Display or South Display depending on the output mode. DP Alternate or
DP over TBT outputs will have hotplug interrupts routed to the North
Display while interrupts for legacy modes will be routed to the South
Display in PCH. This patch adds hotplug interrupt handling support for
DP Alternate mode.

Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
[Paulo: coding style changes]
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180616000530.5357-2-paulo.r.zanoni@intel.com

drm/i915/icl: GSE interrupt moves from DE_MISC to GU_MISC

The Graphics System Event(GSE) interrupt bit has a new location in the
GU_MISC_INTERRUPT_{IIR, ISR, IMR, IER} registers. Since GSE was the only
DE_MISC interrupt that was enabled, with this change we don't enable/handle
any of DE_MISC interrupts for gen11. Credits to Paulo for pointing out
the register change.

v2: from DK
raw_reg_[read/write], branch prediction hint and drop platform check (Mika)

v3: From DK
Early re-enable of master interrupt (Chris)

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
[Paulo: bikesheds and rebases]
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180616000530.5357-1-paulo.r.zanoni@intel.com

drm/i915/i915_reg.h: fix the checkpatch MACRO_ARG_PRECEDENCE issues

While I don't see any issue with the way these macros are being called
today, let's protect them against operator precedence issues before
they happen.

Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180612235654.7914-4-paulo.r.zanoni@intel.com

drm/i915/i915_reg.h: fix the checkpatch SPACE_BEFORE_TAB issues

Since I'm touching the file I might as well fix this class of errors
since they are just a few. Also drive-by fix the styling of the
VLV_TURBO_SOC_OVERRIDE definitions instead of just the spaces before
the tabs.

Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180612235654.7914-3-paulo.r.zanoni@intel.com

drm/i915/i915_reg.h: fix the checkpatch SPACING issues

Because OCD.

Now seriously, commit 1aa920ea0e85 ("drm/i915: add register macro
definition style guide") has finally established a coding standard to
be followed by the rest of the file, and I've been trying to request
everybody to adhere to that since then. The problem is that when
someone adds a new line to a register that has the wrong style, these
people generally propagate the wrong style and I have to keep asking
them to drive-by fix the whole register, which is not something I like
to do and also creates extra work for them. Or I can ignore the
propagation of the wrong coding style and feel anxious about it. On
top of that, we now have our CI happily reminding us about these
problems, which makes everything worse.

So IMHO the best way to proceed is to fix the spacing issues in the
file once and for all. Contributors will stop propagating the bad
style when adding new bits to registers that already have bad style,
we will stop asking them to redo their patches and the CI emails will
become more relevant by having less semi-false errors.

Yes, there will be some pain involved for backporters, but at least
spacing issues like that are easy to spot and fix in the patch files.

This patch was generated by:

../../../../scripts/checkpatch.pl -f --strict --types SPACING \
--fix-inplace i915_reg.h

I manually checked the output and everything seems sane.

v2: Single conflict around the addition of DP_TP_CTL_LINK_TRAIN_PAT4.

Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180618180943.894-1-paulo.r.zanoni@intel.com

drm/i915/audio: Add 810 MHz clock entries to dp_aud_n_m table

Expand the Maud/Naud table according to DP 1.4 spec to include entries for
810 MHz clock. This is required for audio to work with HBR3.

Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180607192013.25872-1-radhakrishna.sripada@intel.com

drm/i915/aml: Introducing Amber Lake platform

Amber Lake uses the same gen graphics as Kaby Lake, including a id
that were previously marked as reserved on Kaby Lake, but that
now is moved to AML page.

So, let's just move it to AML macro that will feed into KBL macro
just to keep it better organized to make easier future code review
but it will be handled as a KBL.

Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180614233720.30517-2-jose.souza@intel.com

drm/i915/whl: Introducing Whiskey Lake platform

Whiskey Lake uses the same gen graphics as Coffe Lake, including some
ids that were previously marked as reserved on Coffe Lake, but that
now are moved to WHL page.

So, let's just move them to WHL macros that will feed into CFL macro
just to keep it better organized to make easier future code review
but it will be handled as a CFL.

v2:
Fixing GT level of some ids

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180614233720.30517-1-jose.souza@intel.com

drm/i915/execlists: Pull the w/a LRI emission into a helper

Having the w/a registers as an open-coded table leaves a trap for the
unwary; it would be easy to miss incrementing the LRI counter when
adding a new register to the list. Instead, pull the list of registers
into a table, so that we only need add new registers to that table
rather than try and remember important side-effects of earlier chunks of
GPU instructions.

Suggested-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180618094150.30895-1-chris@chris-wilson.co.uk

drm/i915: Only show debug for state changes when banning

Since we trigger 10,000s of hangs and resets during selftesting, we emit
many, many thousands of lines of useless debug messages. Reduce the
frequency by only logging a change in state of a guilty context.

Fixes: 14921f3cef85 ("drm/i915: Fix context ban and hang accounting for client")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180618073135.10849-1-chris@chris-wilson.co.uk

drm/i915/lspcon: switch to kernel unsigned int types

We have fairly mixed uintN_t vs. uN usage throughout the driver, but try
to stick to kernel types at least where it's more prevalent.

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1e132575785d9b615208eb60ee5e388df5991172.1528794959.git.jani.nikula@intel.com

drm/i915/audio: switch to kernel unsigned int types

We have fairly mixed uintN_t vs. uN usage throughout the driver, but try
to stick to kernel types at least where it's more prevalent.

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/808b06e1f0a95a4ee892553abf11fdbc30025571.1528794959.git.jani.nikula@intel.com

drm/i915/backlight: switch to kernel unsigned int types

We have fairly mixed uintN_t vs. uN usage throughout the driver, but try
to stick to kernel types at least where it's more prevalent.

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/e68c3f16738eb3ab9f276d797f20326ed6d15848.1528794959.git.jani.nikula@intel.com

drm/i915/dvo: switch to kernel unsigned int types

We have fairly mixed uintN_t vs. uN usage throughout the driver, but try
to stick to kernel types at least where it's more prevalent.

v2: fix checkpatch warning on indentation

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180612095621.21101-1-jani.nikula@intel.com

drm/i915/uncore: switch to kernel unsigned int types

We have fairly mixed uintN_t vs. uN usage throughout the driver, but try
to stick to kernel types at least where it's more prevalent.

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/4af5f30fc9665d1bed1eed09e7f749737749d739.1528794959.git.jani.nikula@intel.com

drm/i915/hdmi: switch to kernel unsigned int types

We have fairly mixed uintN_t vs. uN usage throughout the driver, but try
to stick to kernel types at least where it's more prevalent.

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/d8b79de3d52e1fcaeabf3abfbb2ed99c4397ff2b.1528794959.git.jani.nikula@intel.com

drm/i915/vbt: switch to kernel unsigned int types

We have fairly mixed uintN_t vs. uN usage throughout the driver, but try
to stick to kernel types at least where it's more prevalent.

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ed5de29c280797b20eb625d52592dcbba8326684.1528794959.git.jani.nikula@intel.com

drm/i915: Fix fallout of fake reset along resume

commit b2209e62a450 ("drm/i915/execlists: Reset the CSB head tracking on
reset/sanitization") and commit 1288786b18f7 ("drm/i915: Move GEM sanitize
from resume_early to resume") show the conflicting requirements on the
code. We must reset the GPU before trashing live state on a fast resume
(hibernation debug, or error paths), but we must only reset our state
tracking iff the GPU is reset (or power cycled). This is tricky if we
are disabling GPU reset to simulate broken hardware; we reset our state
tracking but the GPU is left intact and recovers from its stale state.

v2: Again without the assertion for forcewake, no longer required since
commit b3ee09a4de33 ("drm/i915/ringbuffer: Fix context restore upon reset")
as the contexts are reset from the CS ensuring everything is powered up.

Fixes: b2209e62a450 ("drm/i915/execlists: Reset the CSB head tracking on reset/sanitization")
Fixes: 1288786b18f7 ("drm/i915: Move GEM sanitize from resume_early to resume")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180616202534.18767-1-chris@chris-wilson.co.uk

drm/i915: Enable provoking vertex fix on Gen9 systems.

The SF and clipper units mishandle the provoking vertex in some cases,
which can cause misrendering with shaders that use flat shaded inputs.

There are chicken bits in 3D_CHICKEN3 (for SF) and FF_SLICE_CHICKEN
(for the clipper) that work around the issue. These registers are
unfortunately not part of the logical context (even the power context),
and so we must reload them every time we start executing in a context.

Bugzilla: https://bugs.freedesktop.org/103047
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180615190605.16238-1-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: stable@vger.kernel.org

drm/i915/icl: update VBT's child_device_config flags2 field

Some bits from the flags2 field are going to be used in the next
patches, so replace the whole-byte definition with the actual bits and
document their versions.

This patch is based on a patch by Animesh Manna.

Cc: Animesh Manna <animesh.manna@intel.com>
Credits-to: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180614221018.19044-2-paulo.r.zanoni@intel.com

drm/i915/icl: implement DVFS for ICL

ICL DVFS is almost the same as CNL, except for the CDCLK/DDICLK
table. Implement it just like CNL does.

References: commit 48469eced282 ("drm/i915: Use cdclk_state->voltage
on CNL")
References: commit 53e9bf5e8159 ("drm/i915: Adjust system agent
voltage on CNL if required by DDI ports")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180614221018.19044-1-paulo.r.zanoni@intel.com

drm/i915: s/IS_G4X && !IS_GM45/IS_G45/

We have IS_G45 these days. Let's use it instead of the
'IS_G4X && !IS_GM45' construct.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180614180500.2565-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915/execlists: Reset the CSB head tracking on reset/sanitization

We can avoid the mmio read of the CSB pointers after reset based on the
knowledge that the HW always start writing at entry 0 in the CSB buffer.
We need to reset our CSB head tracking after GPU reset (and on
sanitization after resume) so that we are expecting to read from entry
0, hence we reset our head tracking back to the entry before (the last
entry in the ring).

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180615093137.14270-2-chris@chris-wilson.co.uk

drm/i915: Be irqsafe inside reset

As we want to be able to call i915_reset_engine and co from a softirq or
timer context, we need to be irqsafe at all times. So we have to forgo
the simple spin_lock_irq for the full spin_lock_irqsave.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180615093137.14270-1-chris@chris-wilson.co.uk

drm/i915: Fix context ban and hang accounting for client

If client is smart or lucky enough to create a new context
after each hang, our context banning mechanism will never
catch up, and as a result of that it will be saved from
client banning. This can result in a never ending streak of
gpu hangs caused by bad or malicious client, preventing
access from other legit gpu clients.

Fix this by always incrementing per client ban score if
it hangs in short successions regardless of context ban
scoring. The exception are non bannable contexts. They remain
detached from client ban scoring mechanism.

v2: xchg timestamp, tidyup (Chris)
v3: comment, bannable & banned together (Chris)

Fixes: b083a0870c79 ("drm/i915: Add per client max context ban limit")
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180615104429.31477-1-mika.kuoppala@linux.intel.com

drm/i915: Keep the ctx workarounds tightly packed

For each platform, we have a few registers that are rewritten with
different values -- they are not part of a sequence, just different parts
of a masked register set at different times (e.g. platform and gen
workarounds). Consolidate these into a single register write to keep the
table compact, important since we are running of room in the current
fixed sized buffer.

While adjusting the construction of the wa table, make it non fatal so
that the driver still loads but keeping the warning and extra details
for inspection.

Inspecting the changes for a Kabylake system,
Before:
Address val mask read
0x07014 0x20002000 0x00002000 0x00002100
0x0E194 0x01000100 0x00000100 0x00000114
0x0E4F0 0x81008100 0x00008100 0xFFFF8120
0x0E184 0x00200020 0x00000020 0x00000022
0x0E194 0x00140014 0x00000014 0x00000114
0x07004 0x00420042 0x00000042 0x000029C2
0x0E188 0x00080000 0x00000008 0x00008030
0x07300 0x80208020 0x00008020 0x00008830
0x07300 0x00100010 0x00000010 0x00008830
0x0E184 0x00020002 0x00000002 0x00000022
0x0E180 0x20002000 0x00002000 0x00002000
0x02580 0x00010000 0x00000001 0x00000004
0x02580 0x00060004 0x00000006 0x00000004
0x07014 0x01000100 0x00000100 0x00002100
0x0E100 0x00100010 0x00000010 0x00008050

After:
Address val mask read
0x02580 0x00070004 0x00000007 0x00000004
0x07004 0x00420042 0x00000042 0x000029C2
0x07014 0x21002100 0x00002100 0x00002100
0x07300 0x80308030 0x00008030 0x00008830
0x0E100 0x00100010 0x00000010 0x00008050
0x0E180 0x20002000 0x00002000 0x00002000
0x0E184 0x00220022 0x00000022 0x00000022
0x0E188 0x00080000 0x00000008 0x00008030
0x0E194 0x01140114 0x00000114 0x00000114
0x0E4F0 0x81008100 0x00008100 0xFFFF8120

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Oscar Mateo <oscar.mateo@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180615120207.13952-1-chris@chris-wilson.co.uk

drm/i915/dp: Add support for HBR3 and TPS4 during link training

DP spec 1.4 supports training pattern set 4 (TPS4) for HBR3 link
rate. This will be used in link training's channel equalization
phase if supported by both source and sink.
This patch adds the helpers to check if HBR3 is supported and uses
TPS4 in training pattern selection during link training.

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180611222655.5696-2-paulo.r.zanoni@intel.com

drm/i915/icl: Add allowed DP rates for Icelake

For ICL, on Combo PHY the allowed max rates are:
- HBR3 8.1 eDP (DDIA)
- HBR2 5.4 DisplayPort (DDIB)
and for MG PHY/TC DDI Ports allowed DP rates are:
- HBR3 8.1 DisplayPort (DP alternate mode, DP over TBT,
- DP on legacy connector - DDIC/D/E/F)

v2 (from Paulo): Remove misleading comment (Ville).

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: James Ausmus <james.ausmus@intel.com>
[Paulo: bikeshed to keep future platforms on "else", v2.]
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180611222655.5696-1-paulo.r.zanoni@intel.com

drm/i915/icl: start adding the TBT pll

This commit just adds the register addresses and the basic skeleton of
the code. The next commits will expand on more specific functions.

Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180522002558.29262-15-paulo.r.zanoni@intel.com

drm/i915/icl: unconditionally init DDI for every port

On ICP, port present straps (from SFUSE_STRAP PCH register) are no
longer supported. Software should determine the presence through BIOS
VBT, hotplug or other mechanisms.

v2: Improve commit message (Lucas).

Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180522002558.29262-14-paulo.r.zanoni@intel.com

drm/i915/icl: add icelake_get_ddi_pll()

Implement the hardware state readout code.

Thanks to Animesh Manna for spotting this problem.

Cc: Animesh Manna <animesh.manna@intel.com>
Credits-to: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180522002558.29262-11-paulo.r.zanoni@intel.com

drm/i915/gtt: Reduce a pair of runtime asserts

We can stop asserting using WARN_ON as given sufficient CI coverage, we
can rely on using GEM_BUG_ON() to catch problems before merging.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Reviewed-by: Matthew Auld <matthew.william.auld@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180614184218.1606-2-chris@chris-wilson.co.uk

drm/i915/gtt: Cache the PTE encoding of the scratch page

As the most frequent PTE encoding is for the scratch page, cache it upon
creation.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Reviewed-by: Matthew Auld <matthew.william.auld@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180614184218.1606-1-chris@chris-wilson.co.uk

drm/i915/gtt: Free unused page tables on unbind the context

As we cannot reliably change used page tables while the context is
active, the earliest opportunity we have to recover excess pages is when
the context becomes idle. So whenever we unbind the context (it must be
idle, and indeed being evicted) free the unused ptes.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Reviewed-by: Matthew Auld <matthew.william.auld@gmail.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180614134315.5900-2-chris@chris-wilson.co.uk

drm/i915/gtt: Lazily allocate page directories for gen7

As we were only supporting aliasing_ppgtt on gen7 for some time, we
saved a few checks by preallocating the page directories on creation.
However, since we need 2MiB of page directories for each ppgtt, to
support arbitrary numbers of user contexts, we need to be more prudent
in our allocations, and defer the page allocation until it is used. We
don't recover unused pages yet as we found that doing so on the fly
(i.e. altering TLB entries) would confuse the GPU.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Reviewed-by: Matthew Auld <matthew.william.auld@gmail.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180614134315.5900-1-chris@chris-wilson.co.uk

drm/i915: Declare the driver wedged if hangcheck makes no progress

Hangcheck is our back up in case the GPU or the driver gets stuck. It
detects when the GPU is not making any progress and issues a GPU reset.
However, if the driver is failing to make any progress, we can get
ourselves into a situation where we continually try resetting the GPU to
no avail. Employ a second timeout such that if we continue to see the
same seqno (the stalled engine has made no progress at all) over the
course of several hangchecks, declare the driver wedged and attempt to
start afresh.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180602104853.17140-1-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>

drm/i915/execlists: Push the tasklet kick after reset to reset_finish

In the unlikely case where we have failed to keep submitting to the GPU,
we end up with the ELSP queue empty but a pending queue of requests.
Here, we skip the per-engine reset as there is no guilty request, but in
doing so we also skip the engine restart leaving ourselves with a
permanently hung engine. A quick way to recover is by moving the tasklet
kick to execlists_reset_finish() (from init_hw). We still emit the error
on hanging, so the error is not lost but we should be able to recover.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180604073441.6737-2-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>

drm/i915/selftests: Initialise request to silence a compiler

With an old (4.7.3 on 32bit) gcc, it emits a warning for

In file included from drivers/gpu/drm/i915/i915_request.c:1425:0:
drivers/gpu/drm/i915/selftests/i915_request.c: In function ‘live_nop_request’:
drivers/gpu/drm/i915/selftests/i915_request.c:380:21: error: ‘request’ may be used uninitialized in this function [-Werror=maybe-uninitialized]

Silence it by just setting it to NULL on initialisation.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180614124923.18071-1-chris@chris-wilson.co.uk

drm/i915: Turn off g4x DP port in .post_disable()

While Bspec doesn't list a specific sequence for turning off the DP port
on g4x we are getting an underrun if the port is disabled in the
.disable() hook. Looks like the pipe stops when the port stops, and by
that time the plane disable may not have completed yet. Also the plane(s)
seem to end up in some wonky state when this happens as they also signal
another underrun immediately after we turn them back on during the next
enable sequence.

We could add a vblank wait in .disable() to avoid wedging the planes,
but I assume we're still tripping up the pipe in some way. So it seems
better to me to just follow the ILK+ sequence and turn off the DP port
in .post_disable() instead. This sequence doesn't seem to suffer from
this problem. Could be it was always the intended sequence for DP and
the gen4 bspec was just never updated to include it.

Originally we used the bad sequence even on ilk+, but I changed that
in commit 08aff3fe26ae ("drm/i915: Move DP port disable to post_disable
for pch platforms") as it was causing issues on those platforms as well.
I left out g4x then only because I didn't have the hardware to test it.
Now that I do it's fairly clear that the ilk+ sequence is also the
right choice for g4x.

v2: Fix whitespace fail (Jani)
Mention the ilk+ commit (Jani)

Cc: stable@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180613160553.11664-2-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Disallow interlaced modes on g4x DP outputs

Looks like interlaced DP output doesn't work on g4x either. Not all
that surprising considering we already established that interlaced
DP output is busted on VLV/CHV.

Cc: stable@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180613160553.11664-1-ville.syrjala@linux.intel.com

drm/i915: Fix PIPESTAT irq ack on i965/g4x

On i965/g4x IIR is edge triggered. So in order for IIR to notice that
there is still a pending interrupt we have to force and edge in ISR.
For the ISR/IIR pipe event bits we can do that by temporarily
clearing all the PIPESTAT enable bits when we ack the status bits.
This will force the ISR pipe event bit low, and it can then go back
high when we restore the PIPESTAT enable bits.

This avoids the following race:
1. stat = read(PIPESTAT)
2. an enabled PIPESTAT status bit goes high
3. write(PIPESTAT, enable|stat);
4. write(IIR, PIPE_EVENT)

The end result is IIR==0 and ISR!=0. This can lead to nasty
vblank wait/flip_done timeouts if another interrupt source
doesn't trick us into looking at the PIPESTAT status bits despite
the IIR PIPE_EVENT bit being low.

Before i965 IIR was level triggered so this problem can't actually
happen there. And curiously VLV/CHV went back to the level triggered
scheme as well. But for simplicity we'll use the same i965/g4x
compatible code for all platforms.

Cc: stable@vger.kernel.org
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=106033
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105225
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=106030
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180611200258.27121-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915/ddi: Removed unused var from hsw_write_infoframe()

Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180613170710.15080-6-imre.deak@intel.com

drm/i915/ddi: Set HDMI infoframes with pipe clocks enabled

On ICL for setting the HDMI infoframe the pipe clock needs to be
enabled, otherwise accessing the VIDEO_DIP_CTL register will hang the
machine.

Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180613170710.15080-5-imre.deak@intel.com

drm/i915/ddi: Check transcoder instead of port when setting HDMI infoframe

The only requirement by BSpec for setting the HDMI infoframes is on DDI
platforms to do that before enabling the HDMI transcoder function, see
VIDEO_DIP_CTL bit 16. Accordingly check for the transcoder function
disabled state instead of the port's disabled state on DDI platforms.
This is needed by the next patch as it will set the infoframe during
crtc disabling where the port is still enabled.

Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180613170710.15080-4-imre.deak@intel.com

drm/i915/ddi: Push pipe clock enabling to encoders

On ICL the pipe clock needs to be enabled before setting the HDMI
infoframe, but these steps are in the reverse order atm. Move the pipe
clock enabling to the encoders, so reordering of the two steps can be
done in a clean way.

No functional change.

v2:
- Rebased on drm-tip.

Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180613172746.18525-1-imre.deak@intel.com

drm/i915/ddi: s/crtc->config/old_crtc_state in haswell_crtc_disable()

crtc->config points to the old crtc state at the point
display.crtc_disable() is called, so use the more descriptive pointer
instead.

v2:
- Convert one remaining instance of the ptr in the function. (Ville)

Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180613170710.15080-2-imre.deak@intel.com

drm/i915/psr: Kill delays when activating psr back.

The immediate enabling was actually not an issue for the
HW perspective for core platforms that have HW tracking.
HW will wait few identical idle frames before transitioning
to actual psr active anyways.

Now that we removed VLV/CHV out of the picture completely
we can safely remove any delays.

Note that this patch also remove the delayed activation
on HSW and BDW introduced by commit 'd0ac896a477d
("drm/i915: Delay first PSR activation.")'. This was
introduced to fix a blank screen on VLV/CHV and also
masked some frozen screens on other core platforms.
Probably the same that we are now properly hunting and fixing.

v2:(DK): Remove unnecessary WARN_ONs and make some other
         VLV | CHV more readable.
v3: Do it regardless the timer rework.
v4: (DK/CI): Add VLV || CHV check on cancel work at psr_disable.
v5: Kill remaining items and fully rework activation functions.
v6: Rebase on top of VLV/CHV clean-up and keep the reactivation
    on a regular non-delayed work to avoid extra delays on exit
    calls and allow us to add few more safety checks before
    real activation.

Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180613192600.3955-1-rodrigo.vivi@intel.com

drm/i915/gtt: Only keep gen6 page directories pinned while active

In order to be able to evict the gen6 ppgtt, we have to unpin it at some
point. We can simply use our context activity tracking to know when the
ppgtt is no longer in use by hardware, and so only keep it pinned while
being used a request.

For the kernel_context (and thus aliasing_ppgtt), it remains pinned at
all times, as the kernel_context itself is pinned at all times.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180614094103.18025-5-chris@chris-wilson.co.uk

drm/i915: Show CCID in engine dumps

For debugging context issues, knowing what context the GPU is
loading/using is helpful.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180614094103.18025-4-chris@chris-wilson.co.uk

drm/i915: Make the hexdump row offset visually distinct

Currently we use %08x for the row offset, and %08x for the binary
contents of the buffer. This makes it very easily to confuse the two, so
switch to using [%04x] for the start-of-row offset.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180614094103.18025-3-chris@chris-wilson.co.uk

drm/i915: Dump the ringbuffer of the active request for debugging

Sometimes we need to see what instructions we emitted for a request to
try and gather a glimmer of insight into what the GPU is doing when it
stops responding.

v2: Move ring dumping into its own routine

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180614122150.17552-1-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>

drm/i915/dsm: remove unnecessary dsm priv structure

Pass a local acpi_handle around instead of having a static dsm priv
structure. If we need it later, we can always move it to dev_priv, and
the change at hand will make that easier as well.

Care is taken to preserve old behaviour, particularly using the last
non-NULL acpi handle, whether it makes sense or not.

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180614104709.2808-1-jani.nikula@intel.com

drm/i915: Move GEM sanitize from resume_early to resume

This should be a no-op in terms of our control flow, we move the
sanitization (GPU reset) from the bottom of the early resume phase to
the top of the next. However, following hibernation debug, the power
code skips the early resume phase, but as we are about to completely
restore the GTT mappings, we first need to stop the GPU using them i.e.
perform a GPU reset (i915_gem_sanitize()).

Testcase: igt/gem_exec_suspend/basic-S4-devices
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180614094103.18025-1-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>

drm/i915/opregion: move acpi notifier to dev_priv

Get rid of the silly static variable.

Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180613113927.30033-1-jani.nikula@intel.com

drm/i915/perf: make oa format tables const

No reason not to be const.

Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180613114929.14541-1-jani.nikula@intel.com

drm/i915: Make closing request flush mandatory

For symmetry, simplicity and ensuring the request is always truly idle
upon its completion, always emit the closing flush prior to emitting the
request breadcrumb. Previously, we would only emit the flush if we had
started a user batch, but this just leaves all the other paths open to
speculation (do they affect the GPU caches or not?) With mm switching, a
key requirement is that the GPU is flushed and invalidated before hand,
so for absolute safety, we want that closing flush be mandatory.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180612105135.4459-1-chris@chris-wilson.co.uk

drm/i915: Allow DBLSCAN user modes with eDP/LVDS/DSI

When encountering a connector with the scaling mode property both
intel and modesetting ddxs sometimes add tons of DBLSCAN modes
to the output's mode list. The idea presumably being that since the
output will be going through the panel fitter anyway we can pretend
to use any kind of mode.

Sadly that means we can't reject user modes with the DBLSCAN flag
until we know whether we're going to be using the panel's native
mode or the user mode directly. Doing otherwise means X clients using
xf86vidmode/xrandr will get a protocol error (and often self
terminate as a result) when the kernel refuses to use the requested
mode with the DBLSCAN flag.

To undo the regression we'll move the DBLSCAN checks into the
connector->mode_valid() and encoder->compute_config() hooks.

Cc: stable@vger.kernel.org
Cc: Vito Caputo <vcaputo@pengaru.com>
Reported-by: Vito Caputo <vcaputo@pengaru.com>
Fixes: e995ca0b8139 ("drm/i915: Provide a device level .mode_valid() hook")
References: https://lkml.org/lkml/2018/5/21/715
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180524125403.23445-1-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=106804
Tested-by: Arkadiusz Miskiewicz <arekm@maven.pl>

drm/i915/icl: DP_AUX_E is valid on ICL+

Add support for DP_AUX_E. Here we also introduce the bits for the AUX
power well E, however ICL power well support is still not enabled yet,
so the power well is not used.

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180612002512.29783-2-paulo.r.zanoni@intel.com

drm/i915/icl: fix gmbus gpio pin mapping

ICP has GPIO pin 1/2 mapped to combo-phy ports & GPIO pins 9/10/11/12
mapped to tc ports[1-4].
This patch defines GPIOCTL registers for GPIO pins 9-12 & uses them in GPIO
pin mapping table.

Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Madhav Chauhan <madhav.chauhan@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180612002512.29783-1-paulo.r.zanoni@intel.com

drm/i915/icl: Add DDI HDMI level selection for ICL

This patch adds a proper HDMI DDI entry level for vswing
programming sequences on ICL.

Spec doesn't specify any default for HDMI tables,
so let's pick the last entry as the default for now
to stay consistent with older platform like CNL.

Cc: Rakshmi Bhatia <rakshmi.bhatia@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180522002558.29262-8-paulo.r.zanoni@intel.com

drm/i915/gtt: Make gen6 page directories evictable

Currently all page directories are bound at creation using an
unevictable node in the GGTT. This severely limits us as we cannot
remove any inactive ppgtt for new contexts, or under aperture pressure.
To fix this we need to make the page directory into a first class and
unbindable vma. Hence, the creation of a custom vma to wrap the page
directory as opposed to a GEM object.

In this patch, we leave the page directories pinned upon creation.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Reviewed-by: Matthew Auld <matthew.william.auld@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180612120446.13901-1-chris@chris-wilson.co.uk

drm/i915/guc: Add support for define guc_log_size in megabytes.

At this moment we can define GuC logs sizes only using pages.
But GuC also allows use for this values expressed in megabytes.
Lets add support for define guc_log_size in megabytes when we
debug of GuC.

v2:
- change buffers size to more friendly (Michał Wajdeczko)
- merge statements in guc_ctl_log_params_flags() (Michał Wajdeczko)
v3:
- fix ifdef (rename DRM_I915_DEBUG_GUC to CONFIG_DRM_I915_DEBUG_GUC)
(Michał Wajdeczko)
- use SZ_* macros to define buffers sizes (Michał Wajdeczko)

Signed-off-by: Piotr Piórkowski <piotr.piorkowski@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180605151330.9954-2-piotr.piorkowski@intel.com

drm/i915/guc: Move defines with size of GuC logs to intel_guc_log.h

At this moment, we have defined GuC logs sizes in intel_guc_fwif.h, but
as these values are related directly to the GuC logs, and not to API of
GuC parameters, we should move these defines to intel_guc_log.h.

v2:
- change buffers size to more friendly (Michał Wajdeczko)
- remove GUC_LOG_SIZE define (Michał Wajdeczko)
v3:
- use SZ_* macros to define buffers sizes (Michał Wajdeczko)

Signed-off-by: Piotr Piórkowski <piotr.piorkowski@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180605151330.9954-1-piotr.piorkowski@intel.com

drm/i915/guc: Refactoring preparation of the GUC_CTL_CTXINFO parameter

At the moment, the preparation of GUC_CTL_CTXINFO is disordered.
Lets move all GUC_CTL_CTXINFO related operations to one place.

v2:
- move 'ctxnum' and 'base' declarations to USES_GUC_SUBMISSION case
(Michał Wajdeczko)

Signed-off-by: Piotr Piórkowski <piotr.piorkowski@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180604141947.8299-5-piotr.piorkowski@intel.com

drm/i915/guc: Refactoring preparation of the GUC_CTL_LOG_PARAMS parameter

At the moment, the preparation of GUC_CTL_LOG_PARAMS is disordered.
Additionally, in struct intel_guc_log we have an unnecessary field
'flags' which we use only to assign value to GuC parameter.
Lets move all GUC_CTL_LOG_PARAMS related operations to one place,
and lets remove field 'flags' from struct intel_guc_log.

Signed-off-by: Piotr Piórkowski <piotr.piorkowski@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180604141947.8299-4-piotr.piorkowski@intel.com

drm/i915/guc: Refactoring preparation of the GUC_CTL_FEATURE parameter

At the moment, the preparation of GUC_CTL_FEATURE is disordered.
Lets move all GUC_CTL_FEATURE related operations to one place.

Signed-off-by: Piotr Piórkowski <piotr.piorkowski@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180604141947.8299-3-piotr.piorkowski@intel.com

drm/i915/guc: Refactoring preparation of the GUC_CTL_DEBUG parameter

At the moment, the preparation of GUC_CTL_DEBUG is disordered.
Lets move all GUC_CTL_DEBUG related operations to one place.

v2:
- move 'ads' declaration to USES_GUC_SUBMISSION case (Michał Wajdeczko)

Signed-off-by: Piotr Piórkowski <piotr.piorkowski@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180604141947.8299-2-piotr.piorkowski@intel.com

drm/i915/guc: Don't store runtime GuC log level in modparam

Currently we are using modparam as placeholder for GuC log level.
Stop doing this and keep runtime GuC level in intel_guc_log struct.

v2:
- rename functions intel_guc_log_level_[get|set] to
intel_guc_log_[get|set]_level (Michał Wajdeczko)
- remove GEM_BUG_ON from intel_guc_log_get_level() (Michał Wajdeczko)

Signed-off-by: Piotr Piórkowski <piotr.piorkowski@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180604141947.8299-1-piotr.piorkowski@intel.com

drm/i915/gtt: Onionify error handling for gen6_ppgtt_create

Pull the empty stubs together into the top level gen6_ppgtt_create, and
tear each one down on error in proper onion order (rather than use
Joonas' pet hate of calling the cleanup function in indeterminable
state).

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Reviewed-by: Matthew Auld <matthew.william.auld@gmail.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180612081815.3585-2-chris@chris-wilson.co.uk

drm/i915/gtt: Subclass gen6_hw_ppgtt

The legacy gen6 ppgtt needs a little more hand holding than gen8+, and
so requires a larger structure. As I intend to make this slightly more
complicated in the future, separate the gen6 from the core gen8 hw
struct by subclassing. This patch moves the gen6 only features out to
gen6_hw_ppgtt and pipes the new type everywhere that needs it.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180612081815.3585-1-chris@chris-wilson.co.uk

drm/i915/ringbuffer: Serialize load of PD_DIR

After triggering the mm switch with a load of PD_DIR, which may be
deferred unto the MI_SET_CONTEXT on rcs, serialise the next commands
with that load by posting a read of PD_DIR (or else those subsequent
commands may access the stale page tables).

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180611171825.13678-2-chris@chris-wilson.co.uk

drm/i915/gtt: Invalidate GGTT caches after writing the gen6 page directories

When we update the gen6 ppgtt page directories, we do so by writing the
new address into a reserved slot in the GGTT. It appears that when the
GPU reads that entry from the gsm, it uses its small cache and that we
need to invalidate that cache after writing. We don't see an issue
currently as we prefill the ppgtt page directories on creation; and only
create the single aliasing_ppgtt long before we start using the GGTT
(and so before the cache may have a conflicting entry).

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180611171825.13678-1-chris@chris-wilson.co.uk

drm/i915/execlists: Avoid putting the error pointer

On allocation error, do not jump to the unwind handler that tries to
free the error pointer.

Reported-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Fixes: a89d1f921c15 ("drm/i915: Split i915_gem_timeline into individual timelines")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180611153332.14824-1-chris@chris-wilson.co.uk

drm/i915: Wrap around the tail offset before setting ring->tail

The HW only accepts offsets within ring->size, and fails peculiarly if
the RING_HEAD or RING_TAIL is set to ring->size. Therefore whenever we
set ring->head/ring->tail we want to make sure it is within value (using
intel_ring_wrap()).

v2: Double check execlists as well
v3: Remove redundancy with assert_ring_tail_valid()
v4: Just assert in intel_ring_reset() rather than be over-defensive.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> #v2
Link: https://patchwork.freedesktop.org/patch/msgid/20180611110845.31890-2-chris@chris-wilson.co.uk

drm/i915/ringbuffer: Fix context restore upon reset

The discovery with trying to enable full-ppgtt was that we were
completely failing to the load both the mm and context following the
reset. Although we were performing mmio to set the PP_DIR (per-process
GTT) and CCID (context), these were taking no effect (the assumption was
that this would trigger reload of the context and restore the page
tables). It was not until we performed the LRI + MI_SET_CONTEXT in a
following context switch would anything occur.

Since we are then required to reset the context image and PP_DIR using
CS commands, we place those commands into every batch. The hardware
should recognise the no-ops and eliminate the expensive context loads,
but we still have to pay the cost of using cross-powerwell register
writes. In practice, this has no effect on actual context switch times,
and only adds a few hundred nanoseconds to no-op switches. We can improve
the latter by eliminating the w/a around known no-op switches, but there
is an ulterior motive to keeping them.

Always emitting the context switch at the beginning of the request (and
relying on HW to skip unneeded switches) does have one key advantage.
Should we implement request reordering on Haswell, we will not know in
advance what the previous executing context was on the GPU and so we
would not be able to elide the MI_SET_CONTEXT commands ourselves and
always have to emit them. Having our hand forced now actually prepares
us for later.

Now since that context and mm follow the request, we no longer (and not
for a long time since requests took over!) require a trace point to tell
when we write the switch into the ring, since it is always. (This is
even more important when you remember that simply writing into the ring
bears no relation to the current mm.)

v2: Sandybridge has to agree to use LRI as well.

Testcase: igt/drv_selftests/live_hangcheck
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180611110845.31890-1-chris@chris-wilson.co.uk

drm/i915/ringbuffer: Brute force context restore

An issue encountered with switching mm on gen7 is that the GPU likes to
hang (with the VS unit busy) when told to force restore the current
context. We can simply workaround this by substituting the
MI_FORCE_RESTORE flag with a round-trip through the kernel_context,
forcing the context to be saved and restored; thereby reloading the
PP_DIR registers and updating the modified page directory!

v2: Undo attempted optimisation in caller (Tvrtko)

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180611104808.24295-1-chris@chris-wilson.co.uk

drm/i915/skl: Add warn about unsupported CDCLK rates

While checking workarounds related to the CDCLK PLL, I noticed that the
DMC firmware bits for WA#1183 are missing for SKL. After that I
clarified with HW people that it's not needed on SKL, since it doesn't
support eDP1.4 which would be the only thing requiring the problematic
CDCLK clock rates. So in theory we shouldn't ever choose these
frequencies, but add an assert in any case for catching such cases and
for documentation.

v2:
- Move the check to skl_set_cdclk and warn whenever using the
corresponding VCO freq. (Ville)

v3:
- Actually check for the platform. (Ville)

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180608144137.7943-1-imre.deak@intel.com

drm/i915/perf: fix gen11 engine class shift

Use the correct engine class shift value while storing the ctx hw id.
Fixes the copy+paste error from commit 61d5676b5561 ("drm/i915/perf: fix
ctx_id read with GuC & ICL").

Apologies for not spotting this in the original review, the
specific_ctx_id_mask is correct, only the specific_ctx_id had this
problem.

v2: Just use the upper 32 bits of lrc_desc (Chris)
v3: If we use the lrc_desc, we must apply the ctx_id_mask too (Lionel)

Fixes: 61d5676b5561 ("drm/i915/perf: fix ctx_id read with GuC & ICL")
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: intel-gfx@lists.freedesktop.org
Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180604233250.609-2-michel.thierry@intel.com

drm/i915/perf: use the lrc_desc to get the ctx hw id in gen8-10

The upper 32 bits of the lrc_desc (bits 52-32 to be precise) are the
context hw id in GEN8-10, so use them and have one less thing to
maintain in the unlikely case we change the descriptor sw fields.

v2: If we use the lrc_desc, we must apply the ctx_id_mask too (Lionel)

Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180604233250.609-1-michel.thierry@intel.com

drm/i915: Apply batch location restrictions before pinning

We special case the position of the batch within the GTT to prevent
negative self-relocation deltas from underflowing. However, that
restriction is being applied after a trial pin of the batch in its
current position. Thus we are not rejecting an invalid location if the
batch has been used before, leading to an assertion if we happen to need
to rearrange the entire payload. In the worst case, this may cause a GPU
hang on gen7 or perhaps missing state.

References: https://bugs.freedesktop.org/show_bug.cgi?id=105720
Fixes: 2889caa92321 ("drm/i915: Eliminate lots of iterations over the execobjects array")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Martin Peres <martin.peres@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180610194325.13467-2-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>

drm/i915: Refactor unsettting obj->mm.pages

As i915_gem_object_phys_attach() wants to play dirty and mess around
with obj->mm.pages itself (replacing the shmemfs with a DMA allocation),
refactor the gubbins so into i915_gem_object_unset_pages() that we don't
have to duplicate all the secrets.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180611075532.26534-1-chris@chris-wilson.co.uk
Link: https://patchwork.freedesktop.org/patch/msgid/152871104647.1718.8796913290418060204@jlahtine-desk.ger.corp.intel.com

drm/i915: Squash GEM load failure message (again)

Due to a silent conflict (silent because we are trying to fix the CI
test that is meant to exercising these failures!) between commit
51e645b6652c ("drm/i915: Mark the GPU as wedged without error on fault
injection") and commit 8571a05a9dd0 ("drm/i915: Use GEM suspend when
aborting initialisation"), we failed to actually squash the error
message after injecting the load failure.

Rearrange the code to export i915_load_failure() for better logging of
real errors (and quiet logging of injected errors).

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180609111058.2660-1-chris@chris-wilson.co.uk

drm/i915: fix PCH_NOP setting for non-PCH platforms

Setting PCH type to PCH_NOP before checking whether we actually have a
PCH ends up returning true for HAS_PCH_SPLIT() on all non-PCH split
platforms. Fix this by using PCH_NOP only for platforms that actually
have a PCH.

Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180608123330.31003-6-jani.nikula@intel.com

drm/i915: be more strict about HAS_PCH_NOP() usage

HAS_PCH_NOP() implies a PCH platform without south display, not generic
disabled display. Prefer num_pipes == 0 for PCH independent checks.

Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180608123330.31003-5-jani.nikula@intel.com

drm/i915: clean up virtual PCH special case handling

Use intel_pch_type() also for mapping the no PCH case (PCH id 0) to
PCH_NONE to simplify code.

Also make sure that intel_pch_type() knows all the PCH ids returned by
intel_virt_detect_pch(). Loudly fail if this isn't the case; this
shouldn't happen anyway.

Cc: Colin Xu <Colin.Xu@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Colin Xu <Colin.Xu@intel.com>
Reviewed-by: Colin Xu <Colin.Xu@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180608123330.31003-4-jani.nikula@intel.com

drm/i915: document PCH_NOP

There's a difference between PCH_NONE and PCH_NOP: the former means we
don't have a PCH while in the latter we do, but it doesn't have the
south display.

Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180608123330.31003-3-jani.nikula@intel.com

drm/i915: fix guest virtual PCH detection on non-PCH systems

Virtualized non-PCH systems such as Broxton or Geminilake should use
PCH_NONE to indicate no PCH rather than PCH_NOP. The latter is a
specific case to indicate a PCH system without south display.

Reported-by: Colin Xu <Colin.Xu@intel.com>
Cc: Colin Xu <Colin.Xu@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Colin Xu <Colin.Xu@intel.com>
Reviewed-by: Colin Xu <Colin.Xu@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180608123330.31003-2-jani.nikula@intel.com

drm/i915/gtt: Reorder aliasing_ppgtt fini

To allow ourselves to use a first class vma for the aliasing_ppgtt page
directory, we have to reorder the shutdown on module unload to remove
and unpin the aliasing_ppgtt before complaining about any objects left
in the GGTT.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Reviewed-by: Matthew Auld <matthew.william.auld@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180609090151.22007-1-chris@chris-wilson.co.uk

drm/i915/gtt: Remove vgpu check for gen6

Since vgpu is not supported on Haswell or any other gen6/7, we do not
need to check and act upon it's enablement.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180608150435.15010-2-chris@chris-wilson.co.uk

drm/i915/gtt: Remove redundant hsw_mm_switch()

hsw_mm_switch() and gen7_mm_switch() are identical, so let's remove the
redundant specialism.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180608150435.15010-1-chris@chris-wilson.co.uk

drm/i915/gtt: Fix unwind length passed to gen6_ppgtt_clear_range

When we want to unwind an error when allocating the PD for gen6, we call
gen6_ppgtt_clear_range() telling to clear upto the PD we've previously
allocated. However, we passed it an incorrect length, passing it the
endpoint instead. Fortunately, as the start was always 0, this has no
impact today, but tomorrow we want to start using non-zero origins.

Reported-by: Matthew Auld <matthew.william.auld@gmail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Reviewed-by: Matthew Auld <matthew.william.auld@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180608173221.10455-1-chris@chris-wilson.co.uk

drm/i915: Fix sprite destination colorkeying on SKL+

On SKL+ the dst colorkey must be configured on the lower
plane that contains the colorkey. This is in contrast to
most earlier platforms where the dst colorkey is configured
on the plane above.

The hardware will peform dst keying only between two immediately
adjacent (in zorder) planes. Plane 2 will be keyed against plane 1,
plane 3 againts plane 2, and so on. There is no way to key arbitrary
planes against plane 1. Thus offering dst color keying on plane 3+
is pointless. In fact it can be harmful since enabling dst keying on
more than one plane on the same pipe leads to only the top-most of
the planes performing the keying. For any plane lower in zorder the
dst key enable is simply ignored.

v2: s/plane 0/plane 1/ etc. since the hw plane names start from 1
Don't break dst colorkey on pre-SKL sprites (hunk ended in the
wrong patch)

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180529182804.8571-1-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com> #v1

drm/i915: Mark the GPU as wedged without error on fault injection

If we have been instructed (by CI) to inject a fault to load the module
with a wedged GPU, do so quietly less we upset CI.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180607134558.31150-1-chris@chris-wilson.co.uk

drm/i915: Add WaKBLVECSSemaphoreWaitPoll

There is a problem with kbl up to rev E0 where a heavy
memory/fabric traffic from adjacent engine(s) can cause an engine
reset to fail. This traffic can be from normal memory accesses
or it can be from heavy polling on a semaphore wait.

For engine hogging causing a fail, we already fallback to
full reset. Which effectively stops all engines and thus
we only add a workaround documentation.

For the semaphore wait loop poll case, we add one microsecond
poll interval to semaphore wait to guarantee bandwidth for
the reset preration. The side effect is that we make semaphore
completion latencies also 1us longer.

v2: Let full reset handle the adjacent engine idling (Chris)
v3: Skip render engine (Joonas), please checkpatch on define (Mika)

References: https://bugs.freedesktop.org/show_bug.cgi?id=106684
References: VTHSD#2227190, HSDES#1604216706, BSID#0917
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180607172444.17080-1-mika.kuoppala@linux.intel.com

drm/i915: Cancel reset preparations on failed resets

Our reset handling has a retry layer further up in the
chain. As we have told the engine to prepare for reset,
and failed it, make sure to remove that preparation so
that the next attempted reset has a clean slate by triggering
another full prepare cycle for the engines.

v2: ret as int, simplified cleanup (Chris)

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180605160357.32591-1-mika.kuoppala@linux.intel.com

drm/i915/gtt: Push allocation to hw ppgtt constructor

In the next patch, we will subclass the gen6 hw_ppgtt. In order, for the
two different generations of hw ppgtt stucts to be of different size,
push the allocation down to the constructor.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180607163040.9781-1-chris@chris-wilson.co.uk

drm/i915: Decouple vma vfuncs from vm

To allow for future non-object backed vma, we need to be able to
specialise the callbacks for binding, et al, the vma. For example,
instead of calling vma->vm->bind_vma(), we now call
vma->ops->bind_vma(). This gives us the opportunity to later override the
operation for a custom vma.

v2: flip order of unbind/bind

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180607154047.9171-2-chris@chris-wilson.co.uk

drm/i915: Prepare for non-object vma

In order to allow ourselves to use VMA to wrap other entities other than
GEM objects, we need to allow for the vma->obj backpointer to be NULL.
In most cases, we know we are operating on a GEM object and its vma, but
we need the core code (such as i915_vma_pin/insert/bind/unbind) to work
regardless of the innards.

The remaining eyesore here is vma->obj->cache_level and related (but
less of an issue) vma->obj->gt_ro. With a bit of care we should mirror
those on the vma itself.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Reviewed-by: Matthew Auld <matthew.william.auld@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180607154047.9171-1-chris@chris-wilson.co.uk