ath79: lzma-loader: fix syntax error

C compiler can't parse '#else if'.

Fixes: f84a9f7dc095 ("ath79: add support for Huawei AP6010DN")
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16989
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 98f26346cbbb45e5c0417f57846ce1783e884ea2)

ath79: add support for Huawei AP6010DN

Huawei AP6010DN is a dual-band, dual-radio 802.11a/b/g/n 2x2 MIMO
enterprise access point with one Gigabit Ethernet port and PoE
support.

Hardware highlights:
- CPU: AR9344 SoC at 480MHz
- RAM: 128MB DDR2
- Flash: 32MB SPI-NOR
- Wi-Fi 2.4GHz: AR9344-internal radio
- Wi-Fi 5GHz: AR9580 PCIe WLAN SoC
- Ethernet: 10/100/1000 Mbps Ethernet through Atheros AR8035 PHY
- PoE: yes
- Standalone 12V/2A power input
- Serial console externally available through RJ45 port
- External watchdog: CAT706SVI (1.6s timeout)

Serial console:
  9600n8 (9600 baud, no stop bits, no parity, 8 data bits)

MAC addresses:
  Each device has 32 consecutive MAC addresses allocated by
  the vendor, which don't overlap between devices.
  This was confirmed with multiple devices with consecutive
  serial numbers.
  The MAC address range starts with the address on the label.
  To be able to distinguish between the interfaces,
  the following MAC address scheme is used:
    - eth0 = label MAC
    - radio0 (Wi-Fi 2.4GHz) = label MAC + 1
    - radio1 (Wi-Fi 5GHz) = label MAC + 2

Installation:
0. Connect some sort of RJ45-to-USB adapter to "Console" port of the AP

1. Power up the AP

2. At prompt "Press f or F  to stop Auto-Boot in 3 seconds",
   do what they say.
   Log in with default admin password "admin@huawei.com".

3. Boot the OpenWrt initramfs from TFTP using the hidden script "run ramboot".
   Replace IP address as needed:

   > setenv serverip 192.168.1.10
   > setenv ipaddr 192.168.1.1
   > setenv rambootfile openwrt-ath79-generic-huawei_ap6010dn-initramfs-kernel.bin
   > saveenv
   > run ramboot

4. Optional but recommended as the factory firmware cannot be downloaded publicly:
   Back up contents of "firmware" partition using the web interface or ssh:

   $ ssh root@192.168.1.1 cat /dev/mtd11 > huawei_ap6010dn_fw_backup.bin

5. Run sysupgrade using sysupgrade image. OpenWrt
   shall boot from flash afterwards.

Return to factory firmware (using firmware upgrade package downloaded from non-public Huawei website):
1. Start a TFTP server in the directory where
   the firmware upgrade package is located

2. Boot to u-boot as described above

3. Install firmware upgrade package and format the config partitions:

   > update system FatAP6X10XN_SOMEVERSION.bin
   > format_fs

Return to factory firmware (from previously created backup):
1. Copy over the firmware partition backup to /tmp,
   for example using scp

2. Use sysupgrade with force to restore the backup:
   sysupgrade -F huawei_ap6010dn_fw_backup.bin

3. Boot AP to U-Boot as described above

Quirks and known issues:
- The stock firmware has a semi dual boot concept where the primary
kernel uses a squashfs as root partition and the secondary kernel uses
an initramfs. This dual boot concept is circumvented on purpose to gain
more flash space and since the stock firmware's flash layout isn't
compatible with mtdsplit.
- The external watchdog's timeout of 1.6s is very hard to satisfy
during bootup. This is why the GPIO15 pin connected to the watchdog input
is configured directly in the LZMA loader to output the AHB_CLK/2 signal
which keeps the watchdog happy until the wdt-gpio kernel driver takes
over. Because it would also take too long to read the whole kernel image
from flash, the uImage header only includes the loader which then reads
the kernel image from flash after GPIO15 is configured.

Signed-off-by: Marco von Rosenberg <marcovr@selfnet.de>
(cherry picked from commit f84a9f7dc095967e41ced96e1ea5f9b2b9f40af6)
Link: https://github.com/openwrt/openwrt/pull/16978
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

kernel: bump 5.15 to 5.15.173

Removed because they are upstream:
   generic/backport-5.15/430-v6.3-udf-Allocate-name-buffer-in-directory-iterator-on-he.patch
   https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=linux-5.15.y&id=5ea4b73e268bf9e1d26271943f2f7c4517253395

   generic/backport-5.15/431-v6.3-udf-Avoid-directory-type-conversion-failure-due-to-E.patch
   https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=linux-5.15.y&id=8b1d55e43cee631e142d46ee94c91ccd894341e9

Link: https://github.com/openwrt/openwrt/pull/16999
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

kernel: bump 5.15 to 5.15.172

No manual changes needed.

Link: https://github.com/openwrt/openwrt/pull/16999
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

kernel: bump 5.15 to 5.15.171

No manual changes needed.

Link: https://github.com/openwrt/openwrt/pull/16882
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

mac80211: compatibility with kernel 6.6.59

Fix genlmsg_multicast_allns() build error on kernel 6.6.59.
Based on kernel patch https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit?h=v6.6.59&id=e0f83d268974dab0361d11904dfc9acec53f96a6

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16835
(cherry picked from commit 31f1dabb4b9727b300ddaa2801903ae4b72e4e1e)
Link: https://github.com/openwrt/openwrt/pull/16882
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

kernel: bump 5.15 to 5.15.170

Removed because they are upstream:
   generic/backport-5.15/777-netfilter-xtables-fix-typo-causing-some-targets-to-not-load-on-IPv6.patch
   https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=linux-5.15.y&id=90baa455aa7e099152898cfa5eb3928d6152da12

Link: https://github.com/openwrt/openwrt/pull/16882
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

kernel: bump 5.15 to 5.15.169

Added patch:
   generic/backport-5.15/430-v6.3-udf-Allocate-name-buffer-in-directory-iterator-on-he.patch
   This patch fixes the following compile warning:
```
  CC [M]  fs/udf/namei.o
fs/udf/namei.c: In function 'udf_rename':
fs/udf/namei.c:878:1: error: the frame size of 1144 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
  878 | }
      | ^
cc1: all warnings being treated as errors
make[7]: *** [scripts/Makefile.build:289: fs/udf/namei.o] Error 1
```

Link: https://github.com/openwrt/openwrt/pull/16882
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

kernel: bump 5.15 to 5.15.168

Manually adapted:
   bcm27xx/patches-5.15/950-0166-xhci-Use-more-event-ring-segment-table-entries.patch
     I replaced it with the version from main branch which applies more easily
   bcm27xx/patches-5.15/950-0600-xhci-quirks-add-link-TRB-quirk-for-VL805.patch
   bcm27xx/patches-5.15/950-0605-xhci-refactor-out-TRBS_PER_SEGMENT-define-in-runtime.patch
   bcm27xx/patches-5.15/950-0606-usb-xhci-add-VLI_TRB_CACHE_BUG-quirk.patch
   bcm27xx/patches-5.15/950-0717-usb-xhci-add-a-quirk-for-Superspeed-bulk-OUT-transfe.patch
   bcm53xx/patches-5.15/180-usb-xhci-add-support-for-performing-fake-doorbell.patch
   generic/hack-5.15/645-netfilter-connmark-introduce-set-dscpmark.patch

Added patch:
   generic/backport-5.15/777-netfilter-xtables-fix-typo-causing-some-targets-to-not-load-on-IPv6.patch
      This fixes a bug intoduced in this version.

Adapt kernel configuration for newly added option
CONFIG_PROC_MEM_ALWAYS_FORCE.

Link: https://github.com/openwrt/openwrt/pull/16882
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

kernel: r8125: update to v9.014.01

Changelog: https://github.com/openwrt/rtl8125/compare/9.013.02...9.014.01

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry-picked from commit e29bc67f9d8451d3baf80da9358b3a01dc4b20b7)

kernel: r8168: refresh patch

Patches weren't refreshed when r8168 was updated to v8.054.00 in a85e18b53f0f.

Fixes: a85e18b53f0f ("kernel: r8168: update to v8.054.00")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 6490c88c75b3392aca9dae5f4d47a13a0aa35220)

kernel: r8126: update to v10.014.01

Changelog: https://github.com/openwrt/rtl8126/compare/10.013.00...10.014.01

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 562b2c22fff363f060e72c9018d243981b7d6447)

kernel: r8168: update to v8.054.00

Changelog: https://github.com/openwrt/rtl8168/compare/8.053.00...8.054.00

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit a85e18b53f0f645d72806cc6fe46f1603bbdb355)

nu801: Mark as nonshared to build in step 1

Mark the package as nonshared to build it in the target specific build
step 1 of the build bots instead of the architecture generic build step 2.

In the build step 2 it may be left out if we build it using a different
target.

Fixes: #16857
Link: https://github.com/openwrt/openwrt/pull/16859
Signed-off-by: Robert Marko <robimarko@gmail.com>

ipq806x: Fix default MAC addresses on MR42 by moving to nvmem-layout
Partial, single-target update extracted from https://github.com/openwrt/openwrt/commit/d264d3a6

The previous `mac-address-increment` is deprecated, and in particular on
this target means that the kernel is unable to read the MAC address,
causing the system to boot with a new random MAC address each time.

Fixes: https://github.com/openwrt/openwrt/issues/13992
Signed-off-by: Rosen Penev <rosenp@gmail.com>
[rafal.boni@gmail.com: single-target-specific backport from larger change]
Signed-off-by: Rafal Boni <rafal.boni@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16858
Signed-off-by: Robert Marko <robimarko@gmail.com>

mediatek: YunCore AX835: fix voltage regulator

Specifying GPIO_ACTIVE_HIGH on the GPIO for the voltage regulator doesn't
suffice. The regulator itself requires enable-active-high to be set.

Fixes: #16292
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
Link: https://github.com/openwrt/openwrt/pull/16839
Signed-off-by: Robert Marko <robimarko@gmail.com>

ath79: Really fix 5GHz on QCA9886 variant of ZTE MF286

Fix in commit 25eead21c5ab ("ath79: fix 5GHz on QCA9886 variant of ZTE MF286")
was incomplete. A user of such variant popped up, and in the boot log
after installation, we discovered that QCA9886 expects different
pre-calibration data size, than the older QCA9880 variant:

ath10k_pci 0000:00:00.0: qca9888 hw2.0 target 0x01000000 chip_id 0x00000000 sub 0000:0000
ath10k_pci 0000:00:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
ath10k_pci 0000:00:00.0: firmware ver 10.4b-ct-9888-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 59e741e7
ath10k_pci 0000:00:00.0: invalid calibration data length in nvmem-cell 'pre-calibration': 2116 != 12064
ath10k_pci 0000:00:00.0: Loading BDF type 0
ath10k_pci 0000:00:00.0: failed to fetch board data for bus=pci,vendor=168c,device=0056,subsystem-vendor=0000,subsystem-device=0000 from ath10k/QCA9888/hw2.0/board-2.bin
ath10k_pci 0000:00:00.0: failed to fetch board-2.bin or board.bin from ath10k/QCA9888/hw2.0
ath10k_pci 0000:00:00.0: failed to fetch board file: -12
ath10k_pci 0000:00:00.0: could not probe fw (-12)

Explicitly define a pre-calibration nvmem-cell for this variant, and use
it instead of the calibration one, which is shorter.

Fixes: 25eead21c5ab ("ath79: fix 5GHz on QCA9886 variant of ZTE MF286")
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
(cherry picked from commit fc236f3b3c54953805173e5ab571f794eb5ff398)
Link: https://github.com/openwrt/openwrt/pull/16810
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

ipq806x: Fix default MAC addresses on MR52 by moving to `nvmem-layout`

Partial, single-target update extracted from https://github.com/openwrt/openwrt/commit/d264d3a6

The previous `mac-address-increment` is deprecated, and in particular on
this target means that the kernel is unable to read the MAC address,
causing the system to boot with a new random MAC address each time.

Fixes: https://github.com/openwrt/openwrt/issues/15238
Signed-off-by: Rosen Penev <rosenp@gmail.com>
[rafal.boni@gmail.com: single-target-specific backport from larger change]
Signed-off-by: Rafal Boni <rafal.boni@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16774
Signed-off-by: Robert Marko <robimarko@gmail.com>

ipq806x: Revert "ipq806x: swap lan leds for Meraki MR52"

This reverts commit ec8f647d168fa8f3b1eedd9b5fe665f793f3a659, as with the
current kernel version, the change actually causes the same bug it once
may have fixed -- that is, the leds are now again reversed.

I suspect this was due to a switch to a newer kernel version between when
the patch was submitted and now reversing the order of the interfaces, so
that eth0 / the LAN interface is also the interface used for PoE, and eth1
/ the WAN interface is the non-PoE interface.

Signed-off-by: Rafal Boni <rafal.boni@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16779
(cherry picked from commit b5e1544f4d45795ab8750b1054c54c8880b7b96b)
Signed-off-by: Rafal Boni <rafal.boni@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16822
Signed-off-by: Robert Marko <robimarko@gmail.com>

ramips: m4r v4: fix typo

It should be debounce-interval, as with the others.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16802
Signed-off-by: Robert Marko <robimarko@gmail.com>

ath79: add support for MikroTik RouterBOARD 750 r2 (hEX lite)

This patch adds support for the MikroTik RouterBOARD 750 r2, marketed as
hEX lite, a small indoor router with 5x 10/100 Mbps Ethernet ports, one
with PoE in. The device was already supported by the ar71xx target.

Specifications:
 - SoC: Qualcomm Atheros QCA9533
 - Flash: 16 MB SPI NOR
 - RAM: 64 MB
 - Ethernet: 4x 10/100 Mbps LAN, 1x 10/100 Mbps WAN (PoE in)
 - LEDs: 5x Ethernet port activity (green), 1x user (green)
 - Buttons: 1x reset

 See https://mikrotik.com/product/RB750r2 for more details.

Not working:
 - Serial port (already not working in ar71xx)

Flashing:
 TFTP boot initramfs image and then perform sysupgrade. Only the
 "Internet" port will ask for an initramfs image. Follow common
 MikroTik procedure as in https://openwrt.org/toh/mikrotik/common.

(cherry picked from commit 8486c677b8bf36808c5b94857f60ee0fb3d5fa28)
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Link: https://github.com/openwrt/openwrt/pull/13477
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

iptables: backport "nft: track each register individually" from 1.9

From the upstream repo:

Instead of assuming only one register is used, track all 16 regs
individually.

This avoids need for the 'PREV_PAYLOAD' hack and also avoids the need to
clear out old flags:

When we see that register 'x' will be written to, that register state is
reset automatically.

Existing dissector decodes
ip saddr 1.2.3.4 meta l4proto tcp
... as
-s 6.0.0.0 -p tcp

iptables-nft -s 1.2.3.4 -p tcp is decoded correctly because the expressions
are ordered like:

meta l4proto tcp ip saddr 1.2.3.4
                                                                                                                                                                                                                   |
... and 'meta l4proto' did clear the PAYLOAD flag.

The simpler fix is:
ctx->flags &= ~NFT_XT_CTX_PAYLOAD;

in nft_parse_cmp(), but that breaks dissection of '1-42', because
the second compare ('cmp lte 42') will not find the
payload expression anymore.

This commit fixes #11169 and openwrt/packages#22727, and potentially anyone that uses iptables-nft legacy support.

Signed-off-by: Rodrigo B. de Sousa Martins <rodrigo.sousa.577@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16504
[Added patch header]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 44b1993f766e66c13e09d7c09a3c8f85655a446e)

generic: 5.15: add Winbond W25N01KV support

It seems that some Xiaomi AX3000T boards changed to using Winbond W25N01KV
SPI-NAND which is not supported in OpenWrt 23.05 but only in main.

So, backport the support for Winbond W25N01KV from Linux 6.12 to 23.05
as well.

Link: https://github.com/openwrt/openwrt/pull/16669
Signed-off-by: Robert Marko <robimarko@gmail.com>

wireless-regdb: Update to version 2024.10.07

b66b9a1 wireless-regdb: update regulatory database based on preceding changes
5097b4a wireless-regdb: Update regulatory info for Tanzania (TZ) for 2024
29633a6 wireless-regdb: Update regulatory info for Pakistan (PK) for 2024
b44edb2 wireless-regdb: Update regulatory info for Serbia (RS) for 2024
dbfae47 Revert "wireless-regdb: Update regulatory info for Serbia (SR) for 2024"
8e3d27c wireless-regdb: Correct regulatory rules of 6GHz frequency for Türkiye (TR)
8760bc3 wireless-regdb: Update regulatory info for Honduras (HN) for 2023
3ba2c53 wireless-regdb: Update regulatory info for Israel (IL) for 2021
83c175c wireless-regdb: Update regulatory info for Kuwait (KW) for 2022
388c80c wireless-regdb: Update regulatory info for Serbia (SR) for 2024
bf55ed4 wireless-regdb: Add .b4-config
3afe172 wireless-regdb: Update .gitignore
3b34761 wireless-regdb: Correct regulatory rules for China (CN)
003c282 wireless-regdb: Update regulatory info for Philippines (PH) on 6GHz
21fcb86 wireless-regdb: Update regulatory info for Guatemala (GT) for 2020
158f105 wireless-regdb: Update regulatory info for Bahrain (BH) for 2024
218d146 wireless-regdb: Add regulatory info for Namibia (NA) for 2023
aad0c26 wireless-regdb: Update regulatory info for Togo (TG) for 2022
983f551 wireless-regdb: Update regulatory info for El Salvador (SV) on 6GHz
58575b4 wireless-regdb: Update regulatory info for Peru (PE) on 6GHz
bad3985 wireless-regdb: Update regulatory info for New Zealand (NZ) for 2022
c7d1083 wireless-regdb: Update regulatory info for Qatar (QA) on 6GHz

Signed-off-by: Itay Shoshani <itai.sho@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16678
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit a6de2d77843f05714c1e888ba247013310bfe47d)

mpc85xx: p1010: fix NAND devices

Upstream commit 9ba0cae3cac07c21c583f9ff194f74043f90d29c made FSL_IFC
visible and selectable, which means that in order for MTD_NAND_FSL_IFC
to work, it needs these two extra CONFIG options.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16717
Signed-off-by: Robert Marko <robimarko@gmail.com>

ramips: use OKLI loader for TP-Link RE200 v1 and RE210 v1

Using OKLI image to fix the booting stuck issue.

Tested with u-boot extracted from TP-Link stock images
"RE200(EU)_V1_171206.zip" and "RE210(US_CA)_V1_171205.zip".

Fixes: https://github.com/openwrt/openwrt/issues/16296
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16473
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit b62e6f5beb2a574c67ba5159f0049e54cdf25d69)

ramips: introduce TP-Link v1 header OKLI image recipe

It can be used to workaround the booting stuck issue caused by the
u-boot LZMA decompression error.

The new kernel image structure:
+------+------------------+------------------+---------------+-----------------+
| name | tplink-v1 header | OKLI lzma-loader | uImage header | lzma kernel+dtb |
+------+------------------+------------------+---------------+-----------------+
| size |      0x200       |       0xe00      |     0x40      |     dynamic     |
+------+------------------+------------------+---------------+-----------------+

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16473
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 08eecec3558d9adf351e03b58309e69a77de1a36)

ramips: add support for netis N6

This commit adds support for netis N6 WiFi 6 router.

Specification
-------------
- SoC       : MediaTek MT7621AT, MIPS, 880 MHz
- RAM       : 256 MiB
- Flash     : NAND 128 MiB (ESMT PSU1GA30DT)
- WLAN      : MT7905DAN + MT7975DN
  - 2.4 GHz : b/g/n/ax, 574 Mbps, MIMO 2x2
  - 5 GHz   : a/n/ac/ax, 1201 Mbps, MIMO 2x2
- Ethernet  : 10/100/1000 Mbps x5 (1x WAN, 4x LAN)
- USB       : 1x 3.0
- UART      : 3.3V, 115200n8
- Buttons   : 1x Reset
              1x WPS
- LEDs      : 1x Power (green)
              1x System (green)
              1x WAN (green)
              1x WiFi 2.4 GHz (green), controlled by phy
              1x WiFi 5 GHz (green), controlled by phy
              1x WPS (green)
              1x USB (green)
              5x ethernet leds (green), controlled by switch
- Power     : 12 VDC, 1.5 A

Installation
------------
1. Update the router using stock firmware web interface and OpenWrt
   factory.bin image.

Recovery and return to stock
----------------------------
1. Assign your PC a static IP 192.168.1.2 and connect to the router using
   the ethernet cable;
2. Power off the router;
3. Press Reset button, power on the router and wait until ethernet led
   start blinking;
4. Release the button;
5. Open http://192.168.1.1/ (N6 System Recovery Mode) in your browser;
6. Upload OpenWrt factory.bin (or stock firmware *.bin) image and proceed
   with upgrade.

MAC addresses
-------------
+---------+-------------------+
|         | MAC example       |
+---------+-------------------+
| LAN     | dc:xx:xx:49:xx:04 |
| WAN     | dc:xx:xx:49:xx:05 |
| WLAN 2g | dc:xx:xx:19:xx:06 |
| WLAN 5g | dc:xx:xx:79:xx:06 |
+---------+-------------------+
The WLAN MAC prototype was found in 'Factory', 0x4
The LAN MAC was found in 'Factory', 0x7ef20
The WAN MAC was found in 'Factory', 0x7ef26

Known issue
-----------
2.4 GHz WLAN doesn't start with mt76 driver.

Probable reason:
   Original Netis N6 EEPROM contains wrong MT_EE_WIFI_CONF value (0xd2).
   Other routers with the same WLAN hardware (e.g., Routerich AX1800)
   have MT_EE_WIFI_CONF = 0x92.

Workaround (already included in this commit):
   Extract EEPROM to a file at the first time boot and change
   MT_EE_WIFI_CONF (offset 0x190) value from 0xd2 to 0x92. See
   /etc/hotplug.d/firmware/11-mt76-caldata for details.

Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16322
(cherry picked from commit f368e2d5ece1153ec242872f3c48991ed225d9b7)
[ Fix merging onflicts in mt7621.mk, 10_fix_wifi_mac, platform.sh ]
[ Change &ethphy4 -> &mdio in dts file ]
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16436
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

ipq40xx: fix MAC address on Meraki MR33 and MR74 after nvmem-layout

...conversion.
Commit 20736013e910 ("kernel: backport nvmem v6.6 fixes and v6.7 changes")
has caused dthe device to no longer correctly read MAC address from its
onboard 24c64 EEPROM, because "at24" driver doesn't support legacy
nvmem-cell bindings [1] - and there was an explicit config option added
to mandate that behaviour in the following patch:

820-v6.7-0002-nvmem-add-explicit-config-option-to-read-old-syntax-.patch

But some of the devices, MR33 and MR74 included, weren't converted with
that as well.
Convert the definition to use proper fixed-layout binding to fix it.

The offending change was introduced between v23.05.0 and v23.05.1, and
found by bisection:
git bisect start
# status: waiting for both good and bad commits
# good: [bd4f415efacfc03bbe5b79ae1d39c1451f5f7385] OpenWrt v23.05.0: adjust config defaults
git bisect good bd4f415efacfc03bbe5b79ae1d39c1451f5f7385
# status: waiting for bad commit, 1 good commit known
# bad: [a58a86693f8593974ff7c26bb42e280b62a8724c] OpenWrt v23.05.1: adjust config defaults
git bisect bad a58a86693f8593974ff7c26bb42e280b62a8724c
# good: [3d0a78add22754aa891529b6702b5e4c7b837446] qualcommax: only build initramfs if CONFIG_TARGET_ROOTFS_INITRAMFS is set
git bisect good 3d0a78add22754aa891529b6702b5e4c7b837446
# bad: [21e5db97c410f4008c8fe8515fb79a7cde368dbf] build: add CycloneDX SBOM JSON support
git bisect bad 21e5db97c410f4008c8fe8515fb79a7cde368dbf
# good: [89184b15cfce4aaffac8cda87c2fa74f829ace42] mediatek: add build for MT7981 RFB
git bisect good 89184b15cfce4aaffac8cda87c2fa74f829ace42
# bad: [41f27bbb6d0af2f37098b97cd28d5f514a6fc417] bcm53xx: add the latest fix version of brcm_nvram
git bisect bad 41f27bbb6d0af2f37098b97cd28d5f514a6fc417
# good: [b649b0bf7100bdc6adb7e857c74738cab7c47b4c] kernel: nvmem: fix "fixed-layout" & support "mac-base"
git bisect good b649b0bf7100bdc6adb7e857c74738cab7c47b4c
# bad: [20736013e91030005353b401bc4b757ba5e5fa98] kernel: backport nvmem v6.6 fixes and v6.7 changes
git bisect bad 20736013e91030005353b401bc4b757ba5e5fa98
# good: [066971615ff66512bc542b09a90be34c2afe98bb] kernel: backport v6.6 nvmem changes
git bisect good 066971615ff66512bc542b09a90be34c2afe98bb
# first bad commit: [20736013e91030005353b401bc4b757ba5e5fa98] kernel: backport nvmem v6.6 fixes and v6.7 changes

Link: [1] https://github.com/openwrt/openwrt/issues/15393#issuecomment-2212300849
Fixes: 20736013e910 ("kernel: backport nvmem v6.6 fixes and v6.7 changes")
Fixes: https://github.com/openwrt/openwrt/issues/15393
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
(cherry picked from commit ccbffad1ad0ce444bc2497098a1d3d3a086a5f44)
[replace mac-address-increment with #nvmem-cell-cells]
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16624
Signed-off-by: Robert Marko <robimarko@gmail.com>

octeon: ubnt-edgerouter: fix sysupgrade config backup/restore

er is missing from platform_copy_config() and octeon_move_config(), so
config is lost on every sysupgrade.

(cherry-picked from commit 77037b09f3ce3284c8486b73cfaaceac53241990)
Signed-off-by: Jakob Haufe <sur5r@sur5r.net>
Link: https://github.com/openwrt/openwrt/pull/16518
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

tools: bzip2: use static lib and tools

Currently, bzip2 is built with a dynamically linked library on which all
of the bzip2 tools depend on.

However, when trying to use the staging dir bzip2 during building on
Fedora 40 the following error appers:
staging_dir/host/bin/bzip2: error while loading shared libraries: libbz2.so.1.0: cannot open shared object file: No such file or directory

Looking into it, the binary is dynamically linked:
$ ldd staging_dir/host/bin/bzip2
linux-vdso.so.1 (0x00007f5ebd9ff000)
libbz2.so.1.0 => not found
libc.so.6 => /lib64/libc.so.6 (0x00007f5ebd7f5000)
/lib64/ld-linux-x86-64.so.2 (0x00007f5ebda01000)

libbz2.so.1.0 is installed into staging_dir/lib but that directory is not
evaluated for the required libraries and Fedora only ships:
/usr/lib64/libbz2.so.1
/usr/lib64/libbz2.so.1.0.8

Thus it cannot find the libbz2 that bzip2 is linked against and thus
trying to use bzip2 will fail and stop compilation as it is used for
bzip2 compressed tarballs.

So, to avoid OpenWrt compiled bzip2 to even attempt to load a required
library from the host we can just static compile libbz2 and bzip2.

Link: https://github.com/openwrt/openwrt/pull/16520
Signed-off-by: Robert Marko <robimarko@gmail.com>

ipq40xx: fix AP-303H PSE GPIO pin

The GPIO chip is at a different start index compared to OpenWrt master.

Signed-off-by: David Bauer <mail@david-bauer.net>

kernel: r8126: add CONFLICT to rss variant

The rss variant should conflict with the default.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/16460
(cherry picked from b83c7448d3ecd82d6c9e02aded784d6bc3c9ce3c)
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

kernel: r8125: add CONFLICT to rss variant

The rss variant should conflict with the default.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/16460
(cherry picked from d39078c785d37961e8b9a96ba3612bc67c10bf2f)
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

OpenWrt v23.05.5: revert to branch defaults

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

OpenWrt v23.05.5: adjust config defaults

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

build: align SOURCE path for build system and SDK

Building a package in the build system or the SDK results in different
values for the `SOURCE` property, it's either `packages/<package name>`
or `feeds/base/<package name>`. The reason is that the SDK handles
`openwrt.git` as an external feed called while the build system contains
the *base* packages directly.

Since packages created with either method are (ideally) the same (bit
for bit), align the content of SOURCE. To do so this commit creates a
symlink from `feeds/base` to `$(TOPDIR)/package` and adopts the SOURCE
when building from inside the build system.

Signed-off-by: Paul Spooren <mail@aparcar.org>

ipq40xx: re-add label MAC address for FritzBox 4040

The MAC address of the GMAC is contained inside the CWMP-Account
number on the label.

The label MAC address alias was defined previously, but it has been
removed with the switch to IPQESS / DSA.

Restore the label MAC address alias.

Fixes: 27b441cbaf42 ("ipq40xx: drop ESSEDMA + AR40xx DTS nodes")
Signed-off-by: Fabian Bläse <fabian@blaese.de>
Reviewed-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit b22d382ae4eaa1af42930115d91855f402314cac)
Signed-off-by: Tom Herbers <mail@tomherbers.de>
Link: https://github.com/openwrt/openwrt/pull/16459
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

firmware-utils: bump to latest openwrt-23.05

This version bump contains one patch improving compatibility with recent
vendor firmware versions:
  - commit f3b636d0ee47 ("tplink-safeloader: bump EAP610-V3 compat_level")

Signed-off-by: Sander Vanheule <sander@svanheule.net>

realtek: 5.15: backport VLAN fix

With commit a22d359fa56fe0 VLAN handling was fixed for kernel 6.6.
This restored network connectivity of the devices. For easy testing
backport the fix for 5.15 too.

Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/16391
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 35e13244aab36958831195a1d2e152aa3ad0ab6c)
Signed-off-by: Goetz Goerisch <ggoerisch@gmail.com>

ath79: fix I2C pins on GL-AR750

Change I2C pin flags to GPIO_ACTIVE_HIGH and change SDA to GPIO1.

On my late production GL-AR750 (purchased 2024):
SCL = GPIO16
SDA = GPIO1

Bug report:
I2C bus doesn't work in GL-AR750
https://github.com/openwrt/openwrt/issues/16319

Signed-off-by: Ryan Salsbury <ryanrs@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16406
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 2e626ae2d2488f2d3708d3aed57eea7a1402f00e)
Signed-off-by: Ryan Salsbury <ryanrs@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16446
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

ramips: tp-link er605-v2: Remove sysupgrade-tar image

The sysupgrade-tar image build is not defined for this target, do not
add a build instruction for it. The build system will use the definition
from the dna_valokuitu-plus-ex400 board and the build will fail.

This fixes the build of the ramips target.

Fixes: 665c2154ef12 ("ramips: add basic support for tp-link er605-v2")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 746e894877e5130a7d5227cd90f90dfe18cc274b)

ucode: another fix for host installation

The previous host installation fix accidentally moved the rpath settings
out of CMAKE_HOST_OPTIONS and into CMAKE_OPTIONS.

Fixes: ae42ecaad4e7 ("ucode: fix host installation")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 2ee1392e094f9b6fdb2a759e2e29fa203b61e066)

ipq40xx: add PoE passthrough GPIO

Add the GPIO pin of the PoE passthrough switch on the Aruba AP-303H.
Power is activated when the pin is low. It enables a PSE chip, so power
is only supplied to downstream devices when they are 802.3af/at
compliant devices.

Ensure you use a sufficient power supply when chaining a consuming
device after the AP.

Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit b40cc46cc882ff97f2752e7837173ffc9f884eb9)

ramips: mt7621: use lzma-loader for Sercomm NA502s

This fixes a well-known "LZMA ERROR 1" error on Sercomm NA502s, reported
on the OpneWrt forum [0].

[0] https://forum.openwrt.org/t/206640

Signed-off-by: Andreas Böhler <dev@aboehler.at>
(cherry picked from commit 6d89aa29878a93c744e8c752a68bc05d41252cfc)
Link: https://github.com/openwrt/openwrt/pull/16412
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

lldpd: fix reload bug: advertisements shall default to on

Because these capability advertisements default to on in lldpd, they
became absent at reload, and not restart, due to how the reload logic
works ( keep daemon running, send unconfigured and then the new config
via socket ), and it was not evident unless you happened to be looking
for it (e.g. via pcap or tcpdump). It was also not evident from the
manpage ( have now sent patches upstream ).

At reload time, the unconfigure logic disabled them unless they were
explicitly enabled (compare with other settings where 'unconfigure' just
resets them). Now they default to on/enabled at init time, and are
explicitly 'unconfigure'd at startup if the user disables them via:

lldp_mgmt_addr_advertisements=0
lldp_capability_advertisements=0

In other words: explicit is necessary to disable the advertisements.

The same applies to 'configure system capabilities enabled'. Technically
'unconfigure'd is the default but now it is explicit at reload.

Tested on: 23.05.3

Signed-off-by: Paul Donald <newtwen+github@gmail.com>
(cherry picked from commit 708101c1412c42c7fb1d838024513a34424c50ff)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>

lldpd: extended interface(s) parsing to handle patterns

For interface type parameters, the man page documents patterns:
```
*,!eth*,!!eth1

uses all interfaces, except interfaces starting with "eth",
but including "eth1".
```

* Renamed `_ifname` to `_l2dev`.
* get the l2dev via network_get_physdev (and not l3dev)
* Glob pattern `*` is also valid - use noglob for this

The net result is that now interface 'names' including globs '*' and '!'
inversions are included in the generated lldpd configs.

Temporarily `set -o noglob` and then `set +o noglob` to disable & enable
globbing respectively, because when we pass `*` as an interface choice,
other file and pathnames get sucked in from where the init script runs,
and the `*` never makes it to lldpd.

Tested extensively on: 22.03.6, 23.05.3

Signed-off-by: Paul Donald <newtwen+github@gmail.com>
[ squash with commit bumping release version ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 4a81d868db85a7954a73bc6dc4a957bbd6abc813)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>

lldpd: make management address advertisement controllable

Defaults to off.

Available from >= 0.7.15

These are sent in TLV

Signed-off-by: Paul Donald <newtwen+github@gmail.com>
(cherry picked from commit 50021d3222667a9a239451de0422f0508aef4419)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>

lldpd: make capabilities advertisement controllable

Defaults to off.

Only available from >= 1.0.15

These capabilities are sent in TLV.

Signed-off-by: Paul Donald <newtwen+github@gmail.com>
(cherry picked from commit 4d8f56bd59f457fd815e2bb4f87df8c7dad2d4fd)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>

lldpd: note about capabilities

only available from >= 1.0.15

Comments are useful. Apparently this config parameter was committed when
openwrt used an older version of lldpd which did not yet support it.

Signed-off-by: Paul Donald <newtwen+github@gmail.com>
(cherry picked from commit b4769175029ad23833b21960d1b605f629537ad7)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>

lldpd: fix restart

Redirection broke in 5364fe0f01ca ("lldpd: shellcheck fixes")

redirects to /dev/null shall be handled correctly (i.e. last).

This fixes these errors on `/etc/init.d/lldpd reload`:

2024-03-16T20:39:00 [WARN/lldpctl] unknown command from argument 1: `/dev/null`
2024-03-16T20:39:00 [WARN/lldpctl] unknown command from argument 1: `/dev/null`
2024-03-16T20:39:00 [WARN/lldpctl] unknown command from argument 1: `/dev/null`
2024-03-16T20:39:00 [WARN/lldpctl] unknown command from argument 1: `/dev/null`

Tested-on: 22.03.6
Fixes: 5364fe0f01ca ("lldpd: shellcheck fixes")
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
[ improve commit description, add fixes tag ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 8cf1dce428b11740d8335d167b9c1f297d1752d0)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>

lldpd: update URL

update Makefile URL

Signed-off-by: Paul Donald <newtwen@gmail.com>
(cherry picked from commit f753d3152f81bd037e9b7abb1b8c5bf9fe54596b)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>

lldpd: shellcheck fixes

No functionality/behaviour changes; code is synonymous

Tested on: 22.03.6

Signed-off-by: Paul Donald <newtwen@gmail.com>
(cherry picked from commit 5364fe0f01ca11b47c55d78f756d3176748dd0c2)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>

lldpd: implement lldp_policy parameter

For certain lldp_class scenarios (2 & 3) a policy must be set also.
Class 4 is default, although it's good to handle the policy eventuality.

Here, set a default lldp_policy for all lldp_class scenarios. Any
lldp_policy can now be set.

Depends on PR #14584 (which introduced an `if` block)

Tested on 22.03.5, 22.03.6

Signed-off-by: Paul Donald <newtwen@gmail.com>
(cherry picked from commit 497fafb8aea48e764ce0e456f20ab346691e585f)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>

lldpd: Implement location parameter

Previously only partially implemented. After commit
5007f488bb5e1b556052ef246bd3822fed8d09d2 lldp_location was never removed

Now, add the value of lldp_location to the generated config.

The location param has a few syntaxes, so the config acquires the first
usage from the man page: 'address country EU'

Supplementary fix for PR #14193 (this param was included in the original
PR #13018 but the lldp_location fixes were absent from PR #14193).

Tested on 22.03.5, 22.03.6

Signed-off-by: Paul Donald <newtwen@gmail.com>
(cherry picked from commit 53252eeb3b6177b77e23235436b04818a88eafe0)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>

lldpd: fix error "sh: XXXms: bad number"

from commit 3ce909914a12647bec52bcee0a162dd6d158a4f6

The lldpd man page says that "configure lldp tx-interval" can
specify an interval value in milliseconds by appending a "ms" suffix to
the figure. Thus mandating string handling, and not integer comparison.

Tested on 22.03.5

Signed-off-by: Paul Donald <newtwen@gmail.com>
(cherry picked from commit 79ee4cb0397eb9eae34369e33d66b5a1d837a652)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>

lldpd: refactor out ifaces derivation; reuse function

from commit 909f0630663d7ae1471c76154516e3299992a150

Now pass two params to get_config_cid_ifaces() for:

cid_interface
interface

Each of which is a CSV of interfaces.

Tested on 22.03.5

Signed-off-by: Paul Donald <newtwen@gmail.com>
(cherry picked from commit 228d4e7f1b759c11897043dc73ef3c576bc13f7f)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>

lldpd: remove unneeded quotes

from commit a5f715da713304972467612d6934130ce3aa2837

Tested on 22.03.5

Signed-off-by: Paul Donald <newtwen@gmail.com>
(cherry picked from commit 4dcece46a7b4ede7d05d8fb9d31d62406bca74d0)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>

lldpd: remove unneeded quotes and variable quoting

from commit ac771313ebedd2c4bfda8adef47650d45d77c32d

portidsubtype takes 1 of 2 possible keywords which do not need quoting:

         configure lldp portidsubtype ifname | macaddress

The third keyword 'local' is used in the syntax when individual ports
are being defined:

         configure [ports ethX [,…]] lldp portidsubtype local value

When this syntax is used, quoting is useful (see test cases for lldpd).
In the init file, the 'local' syntax is unused.

Tested on 22.03.5

Signed-off-by: Paul Donald <newtwen@gmail.com>
(cherry picked from commit bd1b17d589bc622408cebdd9fa0f43386cc3ef5a)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>

lldpd: remove unneeded quotes and variable quoting

from commit c98ee4dbb3db0f064d990941cdd82e872da76946

agent-type takes 1 of 3 possible keywords which do not require quoting:

         configure lldp agent-type nearest-bridge | nearest-non-tpmr-bridge
         | nearest-customer-bridge

Tested on 22.03.5

Signed-off-by: Paul Donald <newtwen@gmail.com>
(cherry picked from commit 24a4da527f7e70d9916439a78298de2f4e4af653)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>

lldpd: remove unneeded quotes and variable quoting

from commit 3ce909914a12647bec52bcee0a162dd6d158a4f6

'capabilities enabled x' where x is a string of CSV

Tested on 22.03.5

Signed-off-by: Paul Donald <newtwen@gmail.com>
(cherry picked from commit b039641071b1e9ee9654513ef3229bb97cc379af)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>

lldpd: remove unneeded quotes

from commit 3ce909914a12647bec52bcee0a162dd6d158a4f6

Tested on 22.03.5

Signed-off-by: Paul Donald <newtwen@gmail.com>
(cherry picked from commit 82ec853284e44fb85ad702879d18857bd566c7db)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>

lldpd: remove unneeded quotes and variable quoting

from commit 24176a6bdd8f26040a97960868fd0d9ee968d695

Tested on 22.03.5

Signed-off-by: Paul Donald <newtwen@gmail.com>
(cherry picked from commit 20a4dddeb0366a56c14f9128392ffe8d0b62e32d)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>

lldpd: fix a paste error
from commit 1be2088a5247b2cfabe8be991c1e52ddaf780a16

The original PR #13018 did not exhibit this.

Tested on 22.03.5

Signed-off-by: Paul Donald <newtwen@gmail.com>
(cherry picked from commit 4fb8fea6de363aeeeca029ed9801b85cdbf45f0c)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>

lldpd: spell fixes

Supplementary fix for PR #14193

Tested on 22.03.5

Signed-off-by: Paul Donald <newtwen@gmail.com>
(cherry picked from commit 1909b6f8835c1381f859c85394defe993e016edd)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>

lldpd: fix -k 'lldp_no_version' row

Supplementary fix for PR #14193 and commit
b67182008fd124706be0ec3ce67347447554ffd5

Tested on 22.03.5

Signed-off-by: Paul Donald <newtwen@gmail.com>
(cherry picked from commit 97eb3bf76c17328f80554e6a3603de00d835e4c5)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>

lldpd: add option to force EDP

allow EDP support if compiled and add force EDP option

Signed-off-by: Stephen Howell <howels@allthatwemight.be>
(cherry picked from commit d274867c217cade795537af93ff9b209e472e19c)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>

lldpd: only use snmp options when compiled in

prevent SNMP options being passed unless lldpd supports them

Signed-off-by: Stephen Howell <howels@allthatwemight.be>
(cherry picked from commit 8b2d02e48cd2559a52e1cbf04143028e50da6a88)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>

lldpd: Update Makefile package release

increment Makefile package release to reflect changes to init script

Signed-off-by: Stephen Howell <howels@allthatwemight.be>
(cherry picked from commit 1b36d44323cdd467980f83318be0837b8a1fd487)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>

lldpd: add option for tx delay and tx hold

add option to set LLDP transmit delay, hold timers to set update frequency

Signed-off-by: Stephen Howell <howels@allthatwemight.be>
(cherry picked from commit a5f715da713304972467612d6934130ce3aa2837)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>

lldpd: add option to set system platform

add option to override system platform instead of using kernel name

Signed-off-by: Stephen Howell <howels@allthatwemight.be>
(cherry picked from commit 4159acceebeec646fb2ebecdd85561ba140f1ce4)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>

lldpd: add option to force SONMP enabled

add option to force SONMP to be enabled even when no peer detected

Signed-off-by: Stephen Howell <howels@allthatwemight.be>
(cherry picked from commit 4ac134aa78d2b4441b0afd485d1d26dbd53d7276)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>

lldpd: add option to force FDP on

add option to force FDP when no peers detected

Signed-off-by: Stephen Howell <howels@allthatwemight.be>
(cherry picked from commit 1be2088a5247b2cfabe8be991c1e52ddaf780a16)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>

lldpd: set CDP version and allow forcing CDP on

add option to specify CDPv1 or CDPv2 and separately enable or force each

Signed-off-by: Stephen Howell <howels@allthatwemight.be>
(cherry picked from commit b67182008fd124706be0ec3ce67347447554ffd5)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>

lldpd: allow disabling LLDP protcol

add option to allow LLDP disabling while using other supported protocols

Signed-off-by: Stephen Howell <howels@allthatwemight.be>
(cherry picked from commit 61dbe756d8edc1adcd152920f71d6dce26232662)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>

lldpd: add portidsubtype option

add option portidsubtype to correct port identifiers and descriptions

Signed-off-by: Stephen Howell <howels@allthatwemight.be>
(cherry picked from commit ac771313ebedd2c4bfda8adef47650d45d77c32d)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>

lldpd: add agent-type option

add option to set agent-type to control propogation

Signed-off-by: Stephen Howell <howels@allthatwemight.be>
(cherry picked from commit c98ee4dbb3db0f064d990941cdd82e872da76946)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>

lldpd: add LLDP MED options

add option to enable LLDP MED fast-start and set fast-start timer

Signed-off-by: Stephen Howell <howels@allthatwemight.be>
(cherry picked from commit 24176a6bdd8f26040a97960868fd0d9ee968d695)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>

lldpd: option to disable LLDP-MED inventory TLV

add option to disable LLDP-MED inventory TLV transmission

Signed-off-by: Stephen Howell <howels@allthatwemight.be>
(cherry picked from commit 1753498b01d86b8d63349b01cb04026c07c343d9)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>

lldpd: Init adds no-version option

add option to disable advertising kernel version

Signed-off-by: Stephen Howell <howels@allthatwemight.be>
(cherry picked from commit 058f284b1a802fafafb2cfde522693bd43aeaf4d)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>

lldpd: Allow neighbour filtering

add filter option to init script.

Signed-off-by: Stephen Howell <howels@allthatwemight.be>
(cherry picked from commit ac3ed75309e7db93bf2316eccba8106e3fe8f9fc)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>

lldpd: LLDPD binds to only specified interfaces

Bind to the configured system interfaces only. Switchport interfaces
are no longer ignored and uci interface values for LLDPD are honored.

Signed-off-by: Stephen Howell <howels@allthatwemight.be>
(cherry picked from commit 064b4999ad1f37f4c6ccf95a0404007b990ed0ef)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>

lldpd: Init config read on reload

Init script reload with trigger to detect config file update.
Reload command added to attempt non-impactful lldpd reload where
lldpcli can be used to update config without process restart.
Config hash function used to track whether process restart is needed.

Signed-off-by: Stephen Howell <howels@allthatwemight.be>
(cherry picked from commit e483c247dc75723a32d03b5b1149f7fd61ac8ac6)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>

lldpd: add lldp_syscapabilities config option

allow to overwrite the detected system capabilities e.g. if devices
does not operate as bridge.

Signed-off-by: Sebastian Pflieger <sebastian@pflieger.email>
(cherry picked from commit 3ce909914a12647bec52bcee0a162dd6d158a4f6)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>

ucode: fix missing backslash

Fixes: ae42ecaad4e7 ("ucode: fix host installation")
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 9d663c7435752bf17ecec4bfc66c73cde55ed04c)

ncurses: Fix path in ncursesw.pc

The file contains the the /usr/lib path from the toolchain directory and
not from the target directory. The /usr/lib directory for the toolchain
is empty and the shared library is not in the specified paths. On RISCV
the linker of util-linux was finding the libncursesw.so in my host
system, tried to link against it and failed. Fix the .pc file.

Fixes: #15942
Co-authored-by: Thomas Weißschuh <thomas@t-8ch.de>
Link: https://github.com/openwrt/openwrt/pull/16018
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 91573ac145aa70a12b0984ec75507ac648569240)
Link: https://github.com/openwrt/openwrt/pull/16390
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

build: autoconf: set ac_cv_func_setresuid=true

MUSL and eglibc provide these symbols.

Bind needs setresuid() to build properly in recent versions.

Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Link: https://github.com/openwrt/openwrt/pull/15952
(cherry picked from commit 0bd129a5d3b298340e1f6351942a8ccc2ba6eaea)
Link: https://github.com/openwrt/openwrt/pull/16390
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

filogic: add missing 2.5G PHY LEDs configuration for Zyxel EX5700

configure 2.5G PHY LEDs to:

2500/1000: green with blink on TX/RX
100/10: green+yellow with blink on TX/RX

which is similar to other 1G PHY LEDs, which are:

1000: green with blink on TX/RX
100/10: green+yellow with blink on TX/RX

Fixes: 6cc14bf66aa ("filogic: support Telenor branded ZyXEL EX5700")
Signed-off-by: Yan Cangang <nalanzeyu@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16082
(cherry picked from commit 3de653a0af35c2d6fbc0fd14909f362c6b977e4a)
Link: https://github.com/openwrt/openwrt/pull/16390
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

mac80211: Update to version 6.1.110-1

This updates mac80211 to version 6.1.110-1. This code is based on Linux
6.1.110 and contains all fixes included in the upstream wireless
subsystem from that kernel version. This includes many bugfixes and also
some security fixes.

The removed patches are already integrated in upstream Linux 6.1.110.

The following patches were integrated in upstream Linux:
   subsys/311-v6.2-wifi-mac80211-fix-and-simplify-unencrypted-drop-chec.patch
   subsys/312-v6.3-wifi-cfg80211-move-A-MSDU-check-in-ieee80211_data_to.patch
   subsys/313-v6.3-wifi-cfg80211-factor-out-bridge-tunnel-RFC1042-heade.patch
   subsys/314-v6.3-wifi-mac80211-remove-mesh-forwarding-congestion-chec.patch
   subsys/315-v6.3-wifi-mac80211-fix-receiving-A-MSDU-frames-on-mesh-in.patch
   subsys/316-v6.3-wifi-mac80211-add-a-workaround-for-receiving-non-sta.patch
   subsys/321-mac80211-fix-mesh-forwarding.patch
   subsys/322-wifi-mac80211-fix-mesh-path-discovery-based-on-unica.patch
   subsys/329-wifi-mac80211-fix-receiving-mesh-packets-in-forwardi.patch
   subsys/339-wifi-cfg80211-fix-receving-mesh-packets-without-RFC1.patch
   subsys/350-v6.3-wifi-mac80211-Allow-NSS-change-only-up-to-capability.patch
   subsys/351-v6.9-wifi-mac80211-track-capability-opmode-NSS-separately.patch

Link: https://github.com/openwrt/openwrt/pull/16368
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

openssl: update to 3.0.15

OpenSSL 3.0.15 is a security patch release. The most severe CVE fixed in this release is Moderate.

This release incorporates the following bug fixes and mitigations:

  * Fixed possible denial of service in X.509 name checks (CVE-2024-6119)

  * Fixed possible buffer overread in SSL_select_next_proto() (CVE-2024-5535)

Added github releases url as source mirror

Signed-off-by: Ivan Pavlov <AuthorReflex@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16332
(cherry picked from commit 62d3773bf19a3e2f39935c08a8b5b2186777f314)
Link: https://github.com/openwrt/openwrt/pull/16346
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

mbedtls: Update to 2.28.9

This contains a fix for:
CVE-2024-45157:
Unlike previously documented, enabling MBEDTLS_PSA_HMAC_DRBG_MD_TYPE does
not cause the PSA subsystem to use HMAC_DRBG: it uses HMAC_DRBG only when
MBEDTLS_PSA_CRYPTO_EXTERNAL_RNG and MBEDTLS_CTR_DRBG_C are disabled.

Link: https://github.com/openwrt/openwrt/pull/16367
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

kernel: bump 5.15 to 5.15.167

Manually adapted:
   generic/backport-5.15/020-v6.1-05-mm-multi-gen-LRU-groundwork.patch
   ramips/patches-5.15/311-MIPS-use-set_mode-to-enable-disable-the-cevt-r4k-irq.patch

Link: https://github.com/openwrt/openwrt/pull/16366
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

kernel: bump 5.15 to 5.15.166

Manually adapted:
   bcm27xx/patches-5.15/950-0030-Revert-Bluetooth-Always-request-for-user-confirmatio.patch

Link: https://github.com/openwrt/openwrt/pull/16366
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

kernel: bump 5.15 to 5.15.165

Removed because they are upstream:
   generic/pending-5.15/110-v6.3-0001-spidev-Add-Silicon-Labs-EM3581-device-compatible.patch
   https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=linux-5.15.y&id=bff165a3993683daddf3f00563960e7675966f91

   ipq807x/patches-5.15/0004-v5.16-arm64-dts-qcom-msm8996-Move-clock-cells-to-QMP-PHY-c.patch
   https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=linux-5.15.y&id=32f0e52f16d45d743b473659329f93d4a27c68bf

Manually adapted:
   bcm27xx/patches-5.15/950-0040-spi-spidev-Completely-disable-the-spidev-warning.patch
   bcm27xx/patches-5.15/950-0578-spi-spidev-Restore-loading-from-Device-Tree.patch
   generic/pending-5.15/110-v6.3-0002-spidev-Add-Silicon-Labs-SI3210-device-compatible.patch

Adapt kernel configuration for newly added option
CONFIG_ARM64_ERRATUM_3194386.

The leddev_list_lock attribute changed from rwlock_t to spinlock_t in:
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=linux-5.15.y&id=590304b798a3b89e716b6b564f8ad14bc9373d93

Link: https://github.com/openwrt/openwrt/pull/16366
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

ucode: fix host installation

The path for linking libucode.so was not specified for the ucode binary.
This breaks execution of ucode in the host context.

Signed-off-by: David Bauer <david.bauer@uniberg.com>
(cherry picked from commit ae42ecaad4e7b4878083f08a2cba6ce511ac6c43)

treewide: fixup models names for UniFi U6 series

Ubiquiti has a set of UniFi 802.11ax (Wi-Fi 6) AP devices. All models
include "U6" in their names and also have code names with no special
characters (including spaces).

Examples:
1. U6 Lite (codename U6-Lite)
2. U6 Long-Range (codename U6-LR)
3. U6+ (codename U6-PLUS)
4. U6 Pro (codename U6-Pro)
5. U6 Mesh (codename U6-Mesh)
6. U6 Mesh Pro (codename U6-Mesh-Pro)
7. U6 Enterprise (codename U6-Enterprise)

Use proper full names for those devices. Names in OpenWrt/DTS code may
need updating too but it can be handled later.

Cc: Elbert Mai <code@elbertmai.com>
Cc: Daniel Golle <daniel@makrotopia.org>
Cc: Henrik Riomar <henrik.riomar@gmail.com>
Cc: David Bauer <mail@david-bauer.net>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 74879140a1aa0b8a8c237e0b67e94c3508e2e249)

ipq40xx: define config-names for Aruba boards

Aruba boards now ship with multiple DTS and image-configurations per
image. Newer apboot revs expect a configuration for their hardware to be
present.

Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit c7ba5574f52f25334add66c15190b578ac873739)

base-files: fix merge of passwd/shadow/group lines with trailing colons

Empty trailing fields get lost when the lines are split and merged again
at colons, resulting in unparsable entries. Only use the split fields for
matching against the other file, but emit the original line unchanged
to fix the issue.

Fixes: de7ca7dafadf ("base-files: merge /etc/passwd et al at sysupgrade config restore")
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
(cherry picked from commit 9bbaa6f2c0419739fb85d48d0f527cb1622946ee)

tools: libtool: do not symlink files in bootstrap

Another instance of files in build_dir symlinking to staging_dir. While
the symlinks do not currently cause any bugs in the libtool package,
such symlinks were found to make the build more fragile, as writing to
the symlink may accidentally modify the shared file in staging_dir. Pass
--copy to bootstrap to disable the symlinking.

Link: https://github.com/openwrt/openwrt/pull/15825
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
(cherry picked from commit d6e54593198851235906c6ab77c20c6209ab19f5)

include: autotools: do not symlink files in autoreconf

In Gluon's Github Actions CI, we were occasionally seeing bizarre build
errors that looked like a config.sub file had been corrupted, or changed
while it was being executed.

The cause turned out to be an interaction of the symlinks created by
autoreconf (pointing from individual tools' build dirs into
`staging_dir/host/share/automake-1.16`) and OpenWrt's host-build.mk,
which replaced config.guess and config.sub *after* autoreconf. The
result was that the replacement of these files ended up following the
symlinks and writing the files in `staging_dir/host/share/automake-1.16`
instead of a package's build dir. This could cause other packages' builds
to fail if they were currently executing the scripts while they were
being written.

To fix this, disable autoreconf's symlinking feature, so that modifying
these files in a package's build directory can't accidentally affect the
staged versions.

Link: https://github.com/openwrt/openwrt/pull/15825
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
(cherry picked from commit c364cb8e469f9a7de1ed8960163c90e26b2df1ad)