John Crispin [Thu, 21 Apr 2016 19:47:15 +0000 (19:47 +0000)]
tools: firmware-utils: add region code support to mktplinkfw
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 49215
John Crispin [Thu, 21 Apr 2016 19:47:12 +0000 (19:47 +0000)]
tools: firmware-utils: clean up mktplinkfw
Remove the whole board list from mktplinkfw, as OpenWrt doesn't use it and
it was severely out of sync with the list of built images for ar71xx.
Also:
* fix -Wall warnings
* add const where appropriate
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 49214
John Crispin [Thu, 21 Apr 2016 19:47:08 +0000 (19:47 +0000)]
ramips: Add support for ZBT WG3526
The WG3526 is the follow-up to the 2626 and is mostly the same, with the
excaption that the mt7602 has been replaced with the mt7603. The internal wifi
setup has also changed slightly. Based on my tests, everything that worked on
the 2626 works on the 3526 and with roughly the same performance.
v1->v2:
* Remove some references to 2626 that I had missed in the dts.
v2->v3:
* Update patch to match new file structure.
* Removed SD driver to be consistent with other MT7621 targets.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
SVN-Revision: 49213
John Crispin [Thu, 21 Apr 2016 19:47:02 +0000 (19:47 +0000)]
ramips: awake rt305x USB controller
Because of Ralink uboot set USB controller into sleep mode [1]
we check it and awake controller before any registers access.
Fix ticket #21396 [2]
[1] http://marc.info/?l=linux-usb&m=
137398626102108&w=2
[2] https://dev.openwrt.org/ticket/21396
Signed-Off-By: Serge Vasilugin <vasilugin@yandex.ru>
SVN-Revision: 49212
John Crispin [Thu, 21 Apr 2016 19:46:59 +0000 (19:46 +0000)]
ramips: add support for ELECOM WRH-300CR
ELECOM WRH-300CR is MT7620N based very small Wi-Fi router with 64MiB
DDR2 SDRAM, 16MiB SPI Flash, one fast ethernet port, and (internal but
easy-to-access) UART.
it also has internal USB hub and USB card reader which provide one USB
port, one SD card slot, and one microSD card slot.
Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com>
SVN-Revision: 49211
John Crispin [Thu, 21 Apr 2016 19:46:53 +0000 (19:46 +0000)]
lantiq: use new image build process for some images
This adds for some easy images the new build process.
This was only tested on some TP-Link devices, please test.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 49210
John Crispin [Thu, 21 Apr 2016 19:46:49 +0000 (19:46 +0000)]
ramips: update DTS file for Planex DB-WRT01
update DTS files to use jedec,spi-nor compatible string for m25p80 to fix probe issues.
Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
SVN-Revision: 49209
Rafał Miłecki [Wed, 20 Apr 2016 18:14:01 +0000 (18:14 +0000)]
bcm53xx: bump maximum TRX size for devices with serial flash
It was already increased for NAND devices so do the same for the ones
with serial memory.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 49207
John Crispin [Wed, 20 Apr 2016 17:19:08 +0000 (17:19 +0000)]
feeds.conf.default: remove the commented ancient feeds
Cleanup feeds.conf.default by removing the old commented-out feeds:
* x-wrt has not been updated for years and targets WhiteRussian/Kamikaze.
No currect code base available anywhere
* six old feeds from svn.openwrt.org/feeds. These feeds have not been
updated for 4-5 years and their code is currently unavailable
(in svn.openwrt.org)
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
SVN-Revision: 49206
John Crispin [Wed, 20 Apr 2016 17:19:05 +0000 (17:19 +0000)]
ramips: fix support Planex MZK-750DHP.
fix script for Planex MZK-750DHP.
modification of the GPIO definition.
add Profile.
Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
SVN-Revision: 49205
John Crispin [Wed, 20 Apr 2016 17:19:00 +0000 (17:19 +0000)]
ramips: rt3352 usbphy fix in dts-file
Add missing rt3352 usb phy. Fix ticket #20499.
Signed-Off-By:Serge Vasilugin <vasilugin@yandex.ru>
SVN-Revision: 49204
Hauke Mehrtens [Tue, 19 Apr 2016 20:18:50 +0000 (20:18 +0000)]
curl: remove file accidentally committed in r49197
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 49199
Hauke Mehrtens [Tue, 19 Apr 2016 20:14:31 +0000 (20:14 +0000)]
oxnas: clean-up and improve profiles
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 49198
Hauke Mehrtens [Tue, 19 Apr 2016 20:12:41 +0000 (20:12 +0000)]
oxnas: add support for Akitio MyCloud mini
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 49197
Luka Perkov [Tue, 19 Apr 2016 13:46:33 +0000 (13:46 +0000)]
imx6: images: add bootfs.tar.gz build artifact
In order to create a bootable block storage device, both bootfs and rootfs
tarballs are required. However, our current scheme does not export a bootfs
tarball so add the packaging of it here.
Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com>
SVN-Revision: 49196
Hauke Mehrtens [Sun, 17 Apr 2016 22:20:11 +0000 (22:20 +0000)]
ar71xx: add config ATH79_MACH_TL_WA901ND_V4 for kernel 4.4
This config option was not added in commit r49158.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 49195
Hauke Mehrtens [Sun, 17 Apr 2016 22:03:58 +0000 (22:03 +0000)]
ar71xx: fix build error
This fixes a build error introduced in r49193.
This closes #22230
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 49194
Hauke Mehrtens [Sun, 17 Apr 2016 19:10:13 +0000 (19:10 +0000)]
ar71xx: fix build with kernel 4.4
The file linux/mdio-gpio.h was moved to linux/platform_data/mdio-gpio.h
in kernel 4.4
Reported-by: Arjen de Korte <arjen+openwrt@de-korte.org>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 49193
Hauke Mehrtens [Sun, 17 Apr 2016 15:35:18 +0000 (15:35 +0000)]
curl: fix deprecated 'depends' syntax
This was introduced in r49183
Reported-by: swalker
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 49192
Hauke Mehrtens [Sun, 17 Apr 2016 15:16:12 +0000 (15:16 +0000)]
util-linux: update to version 2.28
The following patches were merged upstream:
* 0001-switch_root-improve-statfs-f_type-portability.patch
* 0002-lib-colors-use-static-buffers-when-parse-scheme.patch
* 002-mkostemp.patch
The following patch is not needed any more because all libc
implementations support alloc in sscanf:
* 001-no-printf-alloc.patch
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 49191
Hauke Mehrtens [Sun, 17 Apr 2016 13:24:30 +0000 (13:24 +0000)]
x86: fix platform_export_bootpart() for Xen virtual disks
Virtual disk devices in a Xen virtual machine (DomU) can be /dev/xvda,
/dev/xvdb and so on with partitions like /dev/xdva1. Devices named like
this where not considered before. This resulted in a non working
sysupgrade, because the boot partition could not be found.
Signed-off-by: Alexander Dahl <alex@netz39.de>
Suggested-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 49190
Hauke Mehrtens [Sun, 17 Apr 2016 12:53:31 +0000 (12:53 +0000)]
busybox: update to 1.24.2
Signed-off-by: Magnus Kroken <mkroken@gmail.com>
[remove Kconfig changes]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 49189
Hauke Mehrtens [Sun, 17 Apr 2016 12:53:11 +0000 (12:53 +0000)]
libnl-tiny: backport 'gnet_stats_rate_est64' support
This has been added to the kernel uapi for a while, and makes
sense to have it here too.
At the moment we're using it for query-ing qdisc via netlink
using libnl-tiny.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 49188
Hauke Mehrtens [Sun, 17 Apr 2016 12:52:54 +0000 (12:52 +0000)]
dnsmasq: Add enable parameter in the UCI DHCP host section
Parameter allows to enable/disable static leases; by default the value is 1
to keep backwards compatibility
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 49187
Hauke Mehrtens [Sun, 17 Apr 2016 12:52:37 +0000 (12:52 +0000)]
tools/cmake: update to 3.5.1
Update cmake to 3.5.1
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 49186
Hauke Mehrtens [Sun, 17 Apr 2016 12:52:17 +0000 (12:52 +0000)]
tools/mpfr: update to 3.1.4
Update mpfr to 3.1.4
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 49185
Hauke Mehrtens [Sun, 17 Apr 2016 12:51:57 +0000 (12:51 +0000)]
curl: add flags to allow gc-sections to strip out unused code
Signed-off-by: Dirk Feytons <dirk.feytons@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 49184
Hauke Mehrtens [Sun, 17 Apr 2016 12:51:41 +0000 (12:51 +0000)]
curl: add config option for NTLM support
Signed-off-by: Dirk Feytons <dirk.feytons@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 49183
Hauke Mehrtens [Sun, 17 Apr 2016 12:51:19 +0000 (12:51 +0000)]
curl: upstep to latest version 7.48.0
Signed-off-by: Dirk Feytons <dirk.feytons@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 49182
Hauke Mehrtens [Sun, 17 Apr 2016 12:50:55 +0000 (12:50 +0000)]
hostapd.sh: Add support for "anonymous_identity" config field
The wpa_supplicant supports an "anonymous_identity" field, which some
EAP networks require. From the documentation:
anonymous_identity: Anonymous identity string for EAP (to be used as the
unencrypted identity with EAP types that support different tunnelled
identity, e.g., EAP-TTLS).
This change modifies the hostapd.sh script to propagate this field
from the UCI config to the wpa_supplicant.conf file.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Reviewed-by: Manuel Munz <freifunk@somakoma.de>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 49181
Hauke Mehrtens [Sun, 17 Apr 2016 12:50:30 +0000 (12:50 +0000)]
package: remove .git files from images
If you have your ./files/ directory stored in a git repository,
the .git will be included into images using precious space.
This patch removes .git directories before packing images.
Signed-off-by: Joerg Jungermann <jj@borkum.net>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 49180
Hauke Mehrtens [Sun, 17 Apr 2016 12:49:54 +0000 (12:49 +0000)]
base-files: allow to set arbitrary ip address and netmask
Signed-off-by: Roman Yeryomin <roman@advem.lv>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 49179
Hauke Mehrtens [Sun, 17 Apr 2016 12:49:30 +0000 (12:49 +0000)]
toolchain/uClibc: enable UCLIBC_HAS_OBSOLETE_BSD_SIGNAL
This is required to build net-snmp.
If that options is disabled in uClibc then net-snmp doesn't
detect sighold support on its configuration stage and so
defines HAVE_SIGHOLD as 0. That in its turn causes compilation of
the following branch of timerPause() in apps/snmpnetstat:
------------------>8----------------
int oldmask;
oldmask = sigblock(sigmask(SIGALRM));
if (!signalled) {
sigpause(0);
}
sigsetmask(oldmask);
------------------>8----------------
Now in uClibc all 3 sigblock(), sigmask() and sigsetmask()
were removed back in 2005, see:
https://git.busybox.net/uClibc/commit/?id=
5aa7aa7fa7ec2a0fe567ac0b2595b46add6f3594
And all that causes net-snmp linkage to fail this way:
------------------>8----------------
.libs/if.o: In function `intpr':
if.c:(.text+0x908): undefined reference to `sigmask'
if.c:(.text+0x90e): undefined reference to `sigblock'
if.c:(.text+0x924): undefined reference to `sigsetmask'
------------------>8----------------
If we enable UCLIBC_HAS_OBSOLETE_BSD_SIGNAL in uClibc then
branch with sighold is used in timerPause() and everything builds as
expected.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 49178
Hauke Mehrtens [Sat, 16 Apr 2016 21:05:48 +0000 (21:05 +0000)]
kernel: update kernel 4.4 to version 4.4.7
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 49176
Hauke Mehrtens [Sat, 16 Apr 2016 20:06:34 +0000 (20:06 +0000)]
samba: fix some security problems
This fixes the following security problems:
* CVE-2015-7560
* CVE-2015-5370
* CVE-2016-2110
* CVE-2016-2111
* CVE-2016-2112
* CVE-2016-2115
* CVE-2016-2118
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 49175
Rafał Miłecki [Sat, 16 Apr 2016 08:48:43 +0000 (08:48 +0000)]
mac80211: update brcmfmac including missing boardrev workaround
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 49174
Rafał Miłecki [Fri, 15 Apr 2016 10:11:44 +0000 (10:11 +0000)]
kernel: backport patch making bcm47xxsflash arch independent
This will be needed to use bcm47xxsflash on ARM for BCM53573.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 49168
Rafał Miłecki [Fri, 15 Apr 2016 10:11:31 +0000 (10:11 +0000)]
kernel: use upstream fixes for bgmac and BCM4709(4)
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 49167
Rafał Miłecki [Thu, 14 Apr 2016 05:54:20 +0000 (05:54 +0000)]
bcm53xx: backport BCM5301X earlycon and USB VCC patches
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 49166
Vasilis Tsiligiannis [Wed, 13 Apr 2016 20:52:26 +0000 (20:52 +0000)]
scripts/getver.sh: Use 'git-rev-parse' to detect if tree lies in Git repository
Path to the Git repository directory can be overriden by using the '$GIT_DIR'
environment variable. This patch improves detection of Git repository by using
'git-rev-parse', which respects '$GIT_DIR' environment variable, instead of just
checking the existence of '.git' directory.
Signed-off-by: Vasilis Tsiligiannis <acinonyx@openwrt.gr>
SVN-Revision: 49165
Vasilis Tsiligiannis [Wed, 13 Apr 2016 20:21:38 +0000 (20:21 +0000)]
include/cmake.mk: Add helper macro to handle conditionals for CMake boolean type variables
Signed-off-by: Vasilis Tsiligiannis <acinonyx@openwrt.gr>
SVN-Revision: 49164
Luka Perkov [Wed, 13 Apr 2016 07:33:24 +0000 (07:33 +0000)]
rpcd: update to latest version
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 49162
John Crispin [Sat, 9 Apr 2016 14:47:35 +0000 (14:47 +0000)]
ramips: remove accidentally comitted code
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 49161
Rafał Miłecki [Sat, 9 Apr 2016 13:23:25 +0000 (13:23 +0000)]
bcm53xx: add switch config workaround for R8500 and DIR-885L
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 49160
Rafał Miłecki [Sat, 9 Apr 2016 13:20:19 +0000 (13:20 +0000)]
bcm53xx: fix regression in generating network config
Syntax error was added in r49122.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 49159
John Crispin [Sat, 9 Apr 2016 10:26:46 +0000 (10:26 +0000)]
ar71xx: add TP-Link TL-WA901ND-v4 support
Signed-off-by: Tiziano Bacocco <tizbac2@gmail.com>
SVN-Revision: 49158
John Crispin [Sat, 9 Apr 2016 10:26:41 +0000 (10:26 +0000)]
ar71xx: add support for Compex WPJ342
OpenWrt can be flashed with following uboot commands:
tftpboot 0x80500000 openwrt-ar71xx-generic-wpj342-16M-squashfs-sysupgrade.bin
erase 0x9f030000 +$filesize
cp.b $fileaddr 0x9f030000 $filesize
Signed-off-by: Christian Mehlis <christian@m3hlis.de>
SVN-Revision: 49157
John Crispin [Sat, 9 Apr 2016 10:26:37 +0000 (10:26 +0000)]
ar71xx: fix nondeterministic hangs during bootconsole/console handover
Reconfiguring the UART when the FIFO is not empty may cause the boot to
hang. This hang is extremely suspectible to timing differences; recompiling
the kernel with the same configuration, but different UTS_VERSION
timestamps can yield images that hang more or less often. Sometimes images
are produced that hang reproducibly.
This patch should also make it into one of the next linux-stable releases,
but it's better to get this fixed as soon as possible.
Fixes #21773, #21857.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 49156
John Crispin [Sat, 9 Apr 2016 10:26:34 +0000 (10:26 +0000)]
ar71xx: add OM5P-ACv2 to the OM5P-AC profile
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49155
John Crispin [Sat, 9 Apr 2016 10:26:31 +0000 (10:26 +0000)]
ar71xx: extract ath10k wifi board.bin for the OpenMesh OM5P-ACv2 board
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49154
John Crispin [Sat, 9 Apr 2016 10:26:28 +0000 (10:26 +0000)]
uboot-envtools: add OpenMesh OM5P-ACv2 support
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49153
John Crispin [Sat, 9 Apr 2016 10:26:25 +0000 (10:26 +0000)]
om-watchdog: add OpenMesh OM5P-ACv2 support
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49152
John Crispin [Sat, 9 Apr 2016 10:26:22 +0000 (10:26 +0000)]
ar71xx: enable sysupgrade for the OpenMesh OM5P-ACv2
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49151
John Crispin [Sat, 9 Apr 2016 10:26:18 +0000 (10:26 +0000)]
ar71xx: add user-space support for the OpenMesh OM5P-ACv2
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49150
John Crispin [Sat, 9 Apr 2016 10:26:15 +0000 (10:26 +0000)]
ar71xx: add kernel support for the OpenMesh OM5P-ACv2 board
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49149
John Crispin [Sat, 9 Apr 2016 10:26:11 +0000 (10:26 +0000)]
ar71xx: create profile and build image for the OpenMesh OM5P-AC board
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49148
John Crispin [Sat, 9 Apr 2016 10:26:08 +0000 (10:26 +0000)]
ar71xx: extract ath10k wifi board.bin for the OpenMesh OM5P-AC board
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49147
John Crispin [Sat, 9 Apr 2016 10:26:04 +0000 (10:26 +0000)]
uboot-envtools: add OpenMesh OM5P-AC support
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49146
John Crispin [Sat, 9 Apr 2016 10:26:01 +0000 (10:26 +0000)]
om-watchdog: add OpenMesh OM5P-AC support
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49145
John Crispin [Sat, 9 Apr 2016 10:25:57 +0000 (10:25 +0000)]
ar71xx: enable sysupgrade for the OpenMesh OM5P-AC
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49144
John Crispin [Sat, 9 Apr 2016 10:25:54 +0000 (10:25 +0000)]
scripts/om-fwupgradecfg-gen.sh: add support for the OM5P-AC
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49143
John Crispin [Sat, 9 Apr 2016 10:25:51 +0000 (10:25 +0000)]
ar71xx: add user-space support for the OpenMesh OM5P-AC
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49142
John Crispin [Sat, 9 Apr 2016 10:25:47 +0000 (10:25 +0000)]
ar71xx: add kernel support for the OpenMesh OM5P-AC board
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49141
John Crispin [Sat, 9 Apr 2016 10:25:42 +0000 (10:25 +0000)]
scripts/om-fwupgradecfg-gen.sh: Generate sha256sum for uboot verification
Future Open Mesh u-boot versions are changing the check of the image files
(vmlinux, rootfs) from md5 to sha256. Having both in them should be enough
to ensure backward and forward compatibility.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49140
John Crispin [Sat, 9 Apr 2016 10:25:38 +0000 (10:25 +0000)]
brcmfmac43430-firmware: switch to @GITHUB download alias
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 49139
John Crispin [Sat, 9 Apr 2016 10:25:34 +0000 (10:25 +0000)]
download: add @GITHUB download facility
Define a new alias (@GITHUB) for downloading raw github repository files
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 49138
John Crispin [Sat, 9 Apr 2016 10:25:29 +0000 (10:25 +0000)]
lantiq-dsl: add missing blank in dsl output
blank inserted before ACTATP
Signed-off-by: Florian Eckert <Eckert.Florian@googlemail.com>
SVN-Revision: 49137
John Crispin [Sat, 9 Apr 2016 10:25:24 +0000 (10:25 +0000)]
lantiq-dsl: bugfix latency values swapped for lucistat
swapped wrong latency output
Signed-off-by: Florian Eckert <Eckert.Florian@googlemail.com>
SVN-Revision: 49136
John Crispin [Sat, 9 Apr 2016 10:25:20 +0000 (10:25 +0000)]
lantiq-dsl: bugfix db negative sign after comma
If db is negative minus sign was shown after comma
Signed-off-by: Florian Eckert <Eckert.Florian@googlemail.com>
SVN-Revision: 49135
John Crispin [Sat, 9 Apr 2016 10:25:16 +0000 (10:25 +0000)]
arc770: enable unaligned access handling simulation in software
This enables misaligned access handling by software in Linux kernel.
With some wireless drivers (ath9k-htc and mt7601u for example) we see
misaligned accesses here and there and to cope with that without
fixing stuff in the drivers we're just gracefully handling it on ARC.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
SVN-Revision: 49134
John Crispin [Sat, 9 Apr 2016 10:25:13 +0000 (10:25 +0000)]
arc770: build kmod-ath9k-htc wpad-mini by default
AXS101 beind a development board lacks built-in wireles inerfaces.
So we have to use external USB dongles to turn the board into
wireless router.
The best USB Wi-Fi dongles to work in AP-mode seem to be based on
ath9k-htc chipset.
And so with that change we add support of mentioned dongles in
default and axs101 builds.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
SVN-Revision: 49133
John Crispin [Sat, 9 Apr 2016 10:25:08 +0000 (10:25 +0000)]
mediatek: update patches
adds a few ethernet fixes
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 49132
John Crispin [Sat, 9 Apr 2016 10:25:03 +0000 (10:25 +0000)]
ramips: Disable the SD driver by default on MT7621
The SD driver has been a long and dragging issue on the MT7621 platforms as it hasn't worked for
months resulting in unbootable devices. Until it's fixed, disable it in the default profiles.
Reports / Discussed here:
https://dev.openwrt.org/ticket/21392
https://dev.openwrt.org/ticket/21834
https://dev.openwrt.org/ticket/21995
https://forum.openwrt.org/viewtopic.php?id=59092
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
SVN-Revision: 49131
John Crispin [Sat, 9 Apr 2016 10:24:58 +0000 (10:24 +0000)]
ramips: Fixes for LinkIt 7688
Misc fixes for LinkIt 7688 board:
- Copy the right wireless firmware for the mt7688
- Add back '0065-mt7688-fixes.patch', left out after the move to Linux 4.4.
- Remove SPI_DEV from linux config which otherwise causes a massive warning
- Add wmac to LINKIT7688.dts so wireless works
Signed-off-by: Adam Kent <adam@semicircular.net>
SVN-Revision: 49130
John Crispin [Sat, 9 Apr 2016 10:24:55 +0000 (10:24 +0000)]
ramips: Adjust image size limit for the D-Link DIR-860L B1
Currently the maximum image size defaults to 8Mbyte even though this model has 16Mbyte of flash memory.
Tested and works on my device.
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
SVN-Revision: 49129
John Crispin [Sat, 9 Apr 2016 10:24:52 +0000 (10:24 +0000)]
ramips: fix for Planex MZK-WDPR (lcd control gpio).
add lcd control gpio pin for Planex MZK-WDPR.
LCD board initial timming is GPIO control.
Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
SVN-Revision: 49128
John Crispin [Sat, 9 Apr 2016 10:24:47 +0000 (10:24 +0000)]
ramips: mt7621: fix Ubiquiti EdgeRouter X profile
Remove unnecessary packages to reduce image size so it fits in initramfs (to enable upgrading from factory firmware).
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 49127
John Crispin [Sat, 9 Apr 2016 10:24:44 +0000 (10:24 +0000)]
ramips: mt7621: sync MQmaker WiTi profile name to dts name
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 49126
John Crispin [Sat, 9 Apr 2016 10:24:40 +0000 (10:24 +0000)]
ramips: enable device profiling by dts
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 49125
John Crispin [Sat, 9 Apr 2016 10:24:36 +0000 (10:24 +0000)]
ramips: mt7621: add a device to TARGET_DEVICES after it's definition
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 49124
John Crispin [Sat, 9 Apr 2016 10:24:29 +0000 (10:24 +0000)]
ramips: mt7621: fix initramfs image for ubnt-erx
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 49123
Rafał Miłecki [Sat, 9 Apr 2016 09:59:21 +0000 (09:59 +0000)]
bcm53xx: add basic support for Netgear R7900
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 49122
Rafał Miłecki [Fri, 8 Apr 2016 20:37:14 +0000 (20:37 +0000)]
bcm53xx: add PCI iproc patch adding abort handler
This prevents die() during PCI bus probe.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 49121
Rafał Miłecki [Fri, 8 Apr 2016 20:36:57 +0000 (20:36 +0000)]
Revert "bcm53xx: revert patch removing imprecise abort workaround"
This reverts commit r48961. It didn't fix PCIe host driver issue as
there are more aborts triggered by it.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 49120
Imre Kaloz [Wed, 6 Apr 2016 08:30:28 +0000 (08:30 +0000)]
mwlwifi: upgrade to 10.3.0.17-
20160324
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 49119
Rafał Miłecki [Fri, 1 Apr 2016 16:49:50 +0000 (16:49 +0000)]
bcm53xx: use the final fix for iproc bcma regression
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 49114
Rafał Miłecki [Fri, 1 Apr 2016 16:49:34 +0000 (16:49 +0000)]
bcm53xx: drop unneeded 4.3 SPROM patch
4.3 isn't oficially used anymore but it may be useful for debugging PCI
host driver regression. SPROM driver doesn't seem to work correctly with
4.3:
[ 2.336686] bcma: bus0: Using fallback SPROM failed (err -2)
[ 2.342366] bcma: bus0: No SPROM available
but it at least compiles now.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 49113
John Crispin [Fri, 1 Apr 2016 07:12:17 +0000 (07:12 +0000)]
package/utils/usbutils: Update USB IDs list to snapshot 2015-12-17
Updates USB IDs list to snapshot 2015-12-17 and changes copyright to
2016.
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
SVN-Revision: 49112
John Crispin [Fri, 1 Apr 2016 07:12:14 +0000 (07:12 +0000)]
package/libs/libusb: Update to 1.0.20
Updates libusb to version 1.0.20 and changes copyright to 2016.
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
SVN-Revision: 49111
John Crispin [Fri, 1 Apr 2016 07:12:11 +0000 (07:12 +0000)]
package/libs/lzo: update version to 2.09
Updates lzo to version 2.09 and changes copyright to 2016.
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
SVN-Revision: 49110
John Crispin [Fri, 1 Apr 2016 07:12:07 +0000 (07:12 +0000)]
ar71xx: WPN824N: enable buttons
Enable buttons connected to the GPIOs of the AR9285.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
SVN-Revision: 49109
John Crispin [Fri, 1 Apr 2016 07:12:03 +0000 (07:12 +0000)]
ar71xx: WPN824N: set WLAN LED name
Make use of ap9x_pci_setup_wmac_led_name() to set the name of the WLAN
LED.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
SVN-Revision: 49108
John Crispin [Fri, 1 Apr 2016 07:12:00 +0000 (07:12 +0000)]
ar71xx: fix the revision of a few TP-LINK devices in AR71XX_MODEL to match labels/image names
Let's not confuse users about the revisions of their devices when we can
easily avoid it.
Not tested on real hardware.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 49107
John Crispin [Fri, 1 Apr 2016 07:11:56 +0000 (07:11 +0000)]
ar71xx: avoid AR71XX_MODEL ending with a space on some TP-LINK-like devices
Instead of adding the space when combining $model and $hwver, add the space
to the beginning of $hwver, so the resulting string won't end with a space
when $hwver is set to the empty string.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 49106
John Crispin [Fri, 1 Apr 2016 07:11:53 +0000 (07:11 +0000)]
ar71xx: check both HWID and HWREV on upgrades of TP-LINK devices
There's no reason for us to be more lenient than the stock firmware, so
better check the HWREV as well to avoid bricked devices.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 49105
John Crispin [Fri, 1 Apr 2016 07:11:48 +0000 (07:11 +0000)]
ramips: move different subtarget image generation to separate makefiles to improve maintainability
- all subtarget specific defines are in their own files
- common defines left in main Makefile
- each subtarget makefile idefed with SUBTARGET
- all subtargets compile tested
- few seems to be broken/unneeded things marked with FIXME
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 49104
John Crispin [Fri, 1 Apr 2016 07:11:43 +0000 (07:11 +0000)]
brcm2708: add brcmfmac43430-firmware-sdio for Rasberry Pi 3
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 49103
John Crispin [Fri, 1 Apr 2016 07:11:39 +0000 (07:11 +0000)]
brcmfmac43430-firmware: add new package
This adds the firmware needed for the BCM43438 included in Raspberry Pi 3.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 49102
John Crispin [Fri, 1 Apr 2016 07:11:34 +0000 (07:11 +0000)]
ar71xx: WNR2200: enable control of all LEDs and buttons
This patch provides full GPIO support for WNR2200 (LEDs and buttons).
It exposes all LEDs to operating system, including Ethernet ones.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 49101
John Crispin [Fri, 1 Apr 2016 07:11:27 +0000 (07:11 +0000)]
ar71xx: WNR2200: fix for random WLAN MAC
Fix for invalid/random/duplicate WLAN MAC address in WNR2200.
Permanent platform MAC is calculated and assigned during system startup.
WLAN MAC follows wired Ethernet interface addresses.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 49100
projects / openwrt / staging / yousong.git / log