Leon M. Busch-George [Fri, 17 May 2024 18:10:25 +0000 (20:10 +0200)]
mediatek: filogic: prevent faulty mac address assignment
The vendor U-Boot on the Cudy M3000 and the Yuncore AX835 assign random
mac addresses on boot and set the 'local-mac-address' property which
prevents Openwrt from assigning the correct address from evmem.
This patch removes the alias for ethernet0 so that U-Boot doesn't add the
property, removes the workaround from 02_network, and adds back the nvmem
definition for the M3000.
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
(cherry picked from commit
a55ab9e1343e85021253e9c55f67adf33ad68f09)
Leon M. Busch-George [Fri, 12 Jan 2024 15:10:40 +0000 (16:10 +0100)]
mediatek: filogic: add support for Cudy M3000 v1
Hardware:
SoC: MT7981b
RAM: 256 MB
Flash: 128 MB SPI NAND
Ethernet:
1x 2.5Gbps (rtl8221b)
1x 1Gbps (integrated phy)
WiFi: 2x2 MT7981
Buttons: Reset, WPS
LED: 1x multicolor
Solder on UART:
- remove rubber ring on the bottom
- remove screws
- pull up the cylinder, maybe help by push on an ethernet socket with a screwdriver
- remove the (3) screws holding the board in the frame
- remove the board from the frame to get to the screws for the silver, flat heat shield
- remove the (3) screws holding the heat shield
- solder UART pins to the back of the board
- make sure to have the pins point out on side with the black, finned heat spread
- the markings for the pins are going to be below the silver heat shield
- Vcc is not needed
If you don't intend on using the UART outside of the installation process, you might not
want to solder:
- carefully scrape off the thin layer of epoxy on the holes (not the copper)
- place your pin header with the UART attached in the holes
- the pins, starting with the one closest to the socket:
- Vcc (not required)
- GND
- RX
- TX
- either wedge the header or hold it with your fingers so that the pins stay in contact with the board
Installation (UART):
- attach an Ethernet cable to the 1Gbps port (black) on the router
- hold the reset button while powering the router
- press CTRL-C or wait for the timeout to get to the U-Boot prompt
- prepare a TFTP server on the network to supply ..-initramfs-kernel.bin
- use 'tftpboot' in the U-Boot shell to pull the image
- boot the image using 'bootm'
- push the ..-sysupgrade to the router using your preferred method
- perform the upgrade with 'sysupgrade -n'
There is a recovery mechanism that involves fetching a file called 'recovery.bin' but that is not understood yet.
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
(cherry picked from commit
20e4a18feb3f766b0f6ebec1afc154b345398a7a)
Tianling Shen [Tue, 2 Apr 2024 11:49:42 +0000 (19:49 +0800)]
uboot-mediatek: enable rootwait for jdcloud re-cp-03
Sometimes the mmc deivce may come up later than kernel attempts to
mount rootfs, resulting kernel panic. Enable rootwait to fix it.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Daniel Golle [Sun, 10 Mar 2024 13:29:14 +0000 (13:29 +0000)]
uboot-mediatek: fix patch order
Make sure patch sequence number is unique by moving patch
440-add-jdcloud_re-cp-03.patch -> 441-add-jdcloud_re-cp-03.patch
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit
2302a7c5ad9c894d0530b7700409b2f4ea4bcc91)
Tianling Shen [Thu, 6 Jun 2024 09:08:48 +0000 (17:08 +0800)]
mediatek: fix lan/wan macaddr for jdcloud re-cp-03
The MAC address assigned to lan/wan was reversed.
Fixes: 6e51ff88b053 ("mediatek: add support for JDCloud RE-CP-03")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Rafał Miłecki [Fri, 21 Jul 2023 05:34:25 +0000 (07:34 +0200)]
ath79: replace "mac-address-ascii" with "mac-base"
With upstream accepted "mac-base" binding there is no need for a
downstream "mac-address-ascii" workaround anymore.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit
daaa0c1b250498acbf91697dfc75c9d3fbac3596)
Link: https://github.com/openwrt/openwrt/pull/15917
Jo-Philipp Wich [Sat, 13 Jul 2024 23:27:28 +0000 (01:27 +0200)]
ucode: update to Git
1a8a0bcf725520820802ad433db22d8f64fbed6c (2024-07-11)
96f74b5be829 ubus: make ubus_context first in uc_ubus_connection_t
7e5830edfb38 nl80211: fix datatype of NL80211_BAND_IFTYPE_ATTR_HE_CAP_{MAC,PHY} attrs
5c8fd34bac42 nl80211: fix parsing of NL80211_BAND_ATTR_VHT_MCS_SET attribute
e8d4e4fe967d nl80211: fix decoding of NL80211_BAND_IFTYPE_ATTR_HE_CAP_MCS_SET attribute
30a3f7ad0433 rtnl: store callback in listener registry only on success
9cbe8294909f rtnl: optimize reception of rtnl events
534417132e18 rtnl: increase event socket rx buffer size limit to 1 MiB
3f9811d2f7b7 compiler: close upvalues on loop control statements
ee4af9b55cb4 vm: rework object iteration
a275399dd8e2 uci: refactor uci.changes() to match documentation
1220992631d5 ubus: automatically clear error information
d6fd94014eea uci: automatically clear error information
99837f280b61 uloop: automatically clear error information
ba3855ae3775 lib: fix documentation typo for `pop()` function
be767ae197ba vm: rework `in` operator semantics
4ade84e8fb81 ubus: add explicit support for deferring incoming requests
cfe137be068a uci: remove incorrectly documentated reorder() parameter
e8d78a26da0c lib: introduce socket library
a0ad1d127ae6 build: fix symbol and library detection
674f65ee551d jsdoc: disable default module titles
a33d16a86493 socket: rework error handling
e2b81d869222 uloop: add documentation
953f36c96e8a socket: make socket.send() accept non-string data
f211d5ac666f ubus: fix uc_ubus_have_uloop for eloop+uloop combination
0662de64bd1f socket: add AF_PACKET socket type support
b594ff8a2841 socket: remove leftover debug code
0d823e702bfe socket: fix addrinfo() with omitted service argument
8cf816d615fd socket: fix potential memory leak in connect()
8f5f231d66cd socket: optimize poll() argument handling
36f106056069 socket: remove wrong documentation fragment
525fca224012 socket: uv_to_sockaddr(): fix length calculation for AF_UNIX addresses
3938645ad9e3 socket: support IPv6 addresses in struct conversion routines
3a586dc7ddbe socket: improve uc_socket_connect() behavior
7b269f1cd3d2 socket: improve uc_socket_listen() behavior
fc6f2b89febf socket: handle further socket option value types
d6f25797dad1 socket: add IPv6 socket options
7611487b9a05 socket: implement recvmsg(), sendmsg() and cmsg support
d2e44bfa8b54 core-lib: improved documentation
e0bab40c8578 fs: add truncate() file method
5d305cfb2ab7 fs: add lock() file method
8b0318f7fabe lib: introduce zlib library
73644a036f5a nl80211: move access to tb array out of uc_nl_convert_attr and below
6e3cf83a77a7 nl80211: add support for multi-attribute arrays
6ff24d5488a9 nl80211: update nl80211.h to latest wireless-next
abc2aef28641 nl80211: add wiphy multi-radio support
Fixes: https://github.com/jow-/ucode/issues/186
Fixes: https://github.com/jow-/ucode/issues/187
Fixes: https://github.com/jow-/ucode/issues/188
Fixes: https://github.com/jow-/ucode/issues/193
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Hauke Mehrtens [Wed, 10 Jul 2024 21:52:41 +0000 (23:52 +0200)]
wireless-regdb: Update to version 2024.07.04
Changes:
2a768c4 wireless-regdb: Update regulatory rules for Mongolia (MN) on 6GHz
04875d9 wireless-regdb: Update regulatory rules for Saudi Arabia (SA) on 6GHz
b7bced8 wireless-regdb: Update regulatory rules for South Africa (ZA) on 6GHz
7bc8615 wireless-regdb: Update regulatory info for Thailand (TH) on 6GHz
f901fa9 wireless-regdb: Update regulatory info for Malaysia (MY) for 2022
d72d288 wireless-regdb: Update regulatory info for Morocco (MA) on 6GHz
414face wireless-regdb: Update regulatory info for Chile (CL) on 6GHz
1156a08 wireless-regdb: Update regulatory info for Mexico (MX) on 6GHz
cc6cf7c wireless-regdb: Update regulatory info for Iceland (IS) on 6GHz
ce03cc0 wireless-regdb: Update regulatory info for Mauritius(MU) on 6GHz
7e37778 wireless-regdb: Update regulatory info for Argentina (AR) on 6GHz
56f3a43 wireless-regdb: Update regulatory info for United Arab Emirates (AE) on 6GHz
3cb8b91 wireless-regdb: Update regulatory info for Colombia (CO) on 6GHz
3682ce5 wireless-regdb: Update regulatory info for Costa Rica (CR) for 2021
dd4ffe7 wireless-regdb: Update regulatory info for Dominican Republic (DO) on 6GHz
f8ef7da wireless-regdb: Update regulatory info for Liechtenstein (LI) on 6GHz
a9ecabe wireless-regdb: Update regulatory info for Jordan (JO) for 2022
5a9fdad wireless-regdb: Update regulatory info for Kenya (KE) for 2022
19326c3 wireless-regdb: Update regulatory info for Macao (MO) for 2024
4838054 wireless-regdb: update regulatory database based on preceding changes
Link: https://github.com/openwrt/openwrt/pull/15921
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit
0a24fd91556e7bd4751676b5ce6324193b7a4aca)
Shiji Yang [Sun, 7 Jul 2024 16:05:14 +0000 (00:05 +0800)]
ramips: limit max spi clock frequency to 50 MHz
In the past few years, we have received several reports about SPI
Flash not working properly. This is caused by excessively fast
clock frequency. It's really annoying to fix them one by one. Let's
reduce these aggressive frequencies to 50 MHz. This is a safe and
suggested value in the vendor SDK.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
(cherry picked from commit
73eeac49be566d389df728b5335f7146d03d2f90)
Link: https://github.com/openwrt/openwrt/pull/15919
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Felix Fietkau [Tue, 12 Sep 2023 13:17:23 +0000 (15:17 +0200)]
mac80211: fix mesh id corruption on 32 bit systems
increase size of ifmsh->mbss_changed
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit
20bd3502d3a841457cc06b3aa45646258fdcba9e)
Link: https://github.com/openwrt/openwrt/pull/15836
[Moved the patch to the end of the patch queue]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Florian Eckert [Wed, 13 Mar 2024 12:22:20 +0000 (13:22 +0100)]
linux-firmware: add missing LICENSE_FILES info
Where it is clear which lincense the firmware package has, the missing
information are added.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Signed-off-by: Petr Štetiar <ynezz@true.cz> [backport]
(cherry picked from commit
535d487c41fa09b02c215799449fcd571d1dacac)
Link: https://github.com/openwrt/openwrt/pull/15918
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Florian Eckert [Wed, 13 Mar 2024 12:21:34 +0000 (13:21 +0100)]
linux-firmware: add LICENSE_FILES and LICENSE file handling
The firmware blobs have all different licenses from the different
manufacturers of the binary blobs. This information is contained in the
upstream 'linux-firmware' repositroy.
This commit extends the package handling so that this information can be
added as an additional argument during packages generation.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
(cherry picked from commit
5c14de1d7e715ef882f34925ee6702b847efcbbd)
Link: https://github.com/openwrt/openwrt/pull/15918
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Florian Eckert [Thu, 21 Mar 2024 11:55:01 +0000 (12:55 +0100)]
kernel: update deprecated license information
Update the deprecated license information from GPL-2.0 to GPL-2.0-only
as written in the COPYING file of the linux source tree.
Also add the 'COPYING' file to the PKG_LICENSE_FILES variable.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
(cherry picked from commit
879826154fd3e5ec353117a9c00cecf5e38c4a16)
Link: https://github.com/openwrt/openwrt/pull/15918
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Florian Eckert [Fri, 15 Mar 2024 10:57:14 +0000 (11:57 +0100)]
mac80211: add missing license information
The lincense information for the packages mac80211 are missing.
This commit adds the missing information.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Signed-off-by: Petr Štetiar <ynezz@true.cz> [backport]
(cherry picked from commit
3128157ec71c7be5c2e26a04b1f4b5080ebf870a)
Link: https://github.com/openwrt/openwrt/pull/15918
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Florian Eckert [Wed, 13 Mar 2024 11:41:38 +0000 (12:41 +0100)]
ca-certificates: add missing license information
The package has no licence information. So let's fix it.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
(cherry picked from commit
0da116f25b1a80ac9429fd7d13ee30130494f19e)
Link: https://github.com/openwrt/openwrt/pull/15918
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Florian Eckert [Tue, 19 Mar 2024 14:44:44 +0000 (15:44 +0100)]
wireless-regdb: add missing license information
Add the missing license information PKG_LICENSE and PKG_LICENSE_FILES.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
(cherry picked from commit
7a3deadf91a356b6b0ac25771854f8fa1c3e6980)
Link: https://github.com/openwrt/openwrt/pull/15918
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Wed, 10 Jul 2024 21:03:33 +0000 (23:03 +0200)]
ramips: Refresh kernel patches
The last patches broke this patch, refresh it again.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Felix Fietkau [Fri, 19 Jan 2024 13:48:05 +0000 (14:48 +0100)]
mediatek: fix WED + wifi reset
The WLAN + WED reset sequence relies on being able to receive interrupts from
the card, in order to synchronize individual steps with the firmware.
When WED is stopped, leave interrupts running and rely on the driver turning
off unwanted ones.
WED DMA also needs to be disabled before resetting.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit
2c5b3bee38eb0d76f5afe90f9969b73e19d28685)
Daniel Golle [Thu, 4 Jul 2024 01:19:01 +0000 (02:19 +0100)]
generic: 6.6: mtk_eth_soc: add support for flow-control settings
Add patch implementing operations to get and set flow-control link
parameters of mtk_eth_soc via ethtool.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit
4a2f712f85b5e29c5763e92a0cc47265580157a3)
Daniel Golle [Sat, 6 Jul 2024 03:02:31 +0000 (04:02 +0100)]
generic: 5.15: mtk_eth_soc: import accepted patches
Import patch accepted upstream.
Initial import:
- net: ethernet: mtk_ppe: Change PPE entries number to 16K
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit
27b6838afacfcd79be52b2563b870ae7b3caf8f6)
Daniel Golle [Sun, 16 Jun 2024 12:20:37 +0000 (13:20 +0100)]
generic: 6.6: backport upstream commits for mtk_eth_soc
Backport commit for mtk_eth_soc:
* net: ethernet: mtk_eth_soc: handle dma buffer size soc specific
(torvalds/linux@
c57e558194430d10d5e5f4acd8a8655b68dade13)
Refresh pending patches which require that.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit
98ddfbc56a7ffd5afef7776244998030675faa24)
Rafał Miłecki [Tue, 9 Jul 2024 22:29:06 +0000 (00:29 +0200)]
kernel: backport mtd_wed/mtk_eth_soc patch for devices with more than 4GB of dram
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Daniel Golle [Tue, 28 May 2024 22:48:16 +0000 (23:48 +0100)]
generic: move accepted patches for mtk_eth_soc to backport-5.15
In preparation to update mtk_eth_soc move accepted patches from mediatek
target to backport folder, so other patches on top can be applied more
easily.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit
8730f9e5365956887b75632df29c4b2305cd82e4)
Christian Marangi [Tue, 9 Jul 2024 02:41:21 +0000 (04:41 +0200)]
image: exclude initramfs-images dependency with IB
Exclude initramfs-images dependency with IB as the target is not defined
in such context.
Fixes: cc6a0abcabf7 ("image: make images and artifacts dependent of initramfs")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit
e5d23b5aa5346de30befc2b05000a3967ca5b460)
Christian Marangi [Mon, 8 Jul 2024 11:10:52 +0000 (13:10 +0200)]
image: make images and artifacts dependent of initramfs
There is currently a BIG bug in how the images dependency is handled and
recent Per Device Rootfs made this more clear and less statistical.
There is currently no dependency between images/artifacts build with
initramfs build. This cause whatever additional image that depends on an
initramfs image to fail as it might happen that image and initramfs
build are called at the same time and the additional image is called
before initramfs build has finished.
Each image-command assume the source image to be taken from the /bin
directory but that is only copied from the /tmp directory only at the
end of the process.
Artifacts currently depends on image with the use of the
BOARD-NAME-images Makefile target, but this is not the case for
initramfs that also define a -images Makefile target but that is not
accounted in images (that might depend on some initramfs images)
To actually fix this, introduce a new Makefile target, -initramfs-images
and make image and artifacts build to depend on this. Since initramfs
images are optional, this dependency is actived only when initramfs
image are built.
With this change we correctly enforce the build order:
- Initramfs Images (optional)
- Images
- Artifacts
(cherry picked from commit
cc6a0abcabf718df872c0f6876d1121d3dd09953)
[ rebased on openwrt-23.05 ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Stefan Weil [Thu, 2 Mar 2023 20:45:50 +0000 (21:45 +0100)]
ramips: add Edimax BR-6208AC V2 support
Specifications:
- Device: Edimax BR-6208AC V2
- SoC: MT7620A
- Flash: 16 MiB
- RAM: 64 MiB
- Switch: 1 WAN, 3 LAN (10/100 Mbps)
- WiFi: MT7620 2.4 GHz + MT7610E 5 GHz
- LEDs: 1x POWER (green, not configurable)
1x Firmware (green, configurable)
1x Internet (green, configurable)
1x VPN (green, configurable)
1x 2.4G (green, not configurable)
1x 5G (green, not configurable)
Normal installation:
- Upload the sysupgrade image via the default web interface
Installation with U-Boot and TFTP:
- Requires a TFTP server which provides the sysupgrade image
- Requires a connection to the serial port of the device, rate 57600
Signed-off-by: Stefan Weil <sw@weilnetz.de>
(cherry picked from commit
8d06bc175154db42a0550212a4b8474008939b34)
Wenli Looi [Thu, 30 Mar 2023 22:28:23 +0000 (22:28 +0000)]
ramips: add support for Netgear EAX12 series
Netgear EAX12, EAX11v2, EAX15v2 are wall-plug 802.11ax (Wi-Fi 6)
extenders that share the SoC, WiFi chip, and image format with the
WAX202.
Specifications:
* MT7621, 256 MiB RAM, 128 MiB NAND
* MT7915: 2.4/5 GHz 2x2 802.11ax (DBDC)
* Ethernet: 1 port 10/100/1000
* UART: 115200 baud (labeled on board)
All LEDs and buttons appear to work without state_default.
Installation:
* Flash the factory image through the stock web interface, or TFTP to
the bootloader. NMRP can be used to TFTP without opening the case.
Revert to stock firmware:
* Flash the stock firmware to the bootloader using TFTP/NMRP.
References in GPL source:
https://www.downloads.netgear.com/files/GPL/EAX12_EAX11v2_EAX15v2_GPL_V1.0.3.34_src.tar.gz
* target/linux/ramips/dts/mt7621-rfb-ax-nand.dts
DTS file for this device.
Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
(cherry picked from commit
32ea8a9a7e4b1319607ae398e9bf7d8e3c4cd756)
Arınç ÜNAL [Sat, 17 Jun 2023 18:59:26 +0000 (21:59 +0300)]
ramips: add wan2 support for MQmaker WiTi
The PHY of the wan2 port on MQmaker WiTi is wired to the second MAC of the
SoC. Rename the wan interface to wan1 and define it under the switch node,
effectively disabling the PHY muxing of the MT7530 switch's phy4.
Define the PHY of the wan2 port and adjust the gmac1 node accordingly. Now
that the PHY muxing feature is not being used anymore, the wan2 port can be
used to achieve 2 Gbps total bandwidth to the CPU.
Tested-by: Demetris Ierokipides <ierokipides.dem@gmail.com>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
(cherry picked from commit
8bf9a8a5e6e35afcb8b7aaebfea6fb91e76c9d81)
Alexey Bartenev [Wed, 31 May 2023 14:50:23 +0000 (10:50 -0400)]
ramips: add support for D-Link DIR-806A B1 router
General specification:
SoC Type: MediaTek MT7620A (580MHz)
ROM: 8 MB SPI-NOR (MX25L6406E)
RAM: 64 MB DDR (W9751G6KB-25)
Switch: MediaTek MT7530
Ethernet: 5 ports - 5×100MbE (WAN, LAN1-4)
Wireless: 2.4 GHz (MediaTek RT5390): b/g/n
Wireless: 5 GHz (MediaTek MT7610EN): ac/n
Buttons: 2 button (POWER, WPS/RESET)
Bootloader: U-Boot 1.1.3
Power: 12 VDC, 0.5 A
MACs:
| LAN | [Factory + 0x04] - 2 |
| WLAN 2.4g | [Factory + 0x04] - 1 |
| WLAN 5g | [Factory + 0x8004] - 3 |
| WAN | [Factory + 0x04] - 2 |
OEM easy installation:
1. Use a PC to browse to http://192.168.0.1.
2. Go to the System section and open the Firmware Update section.
3. Under the Local Update at the right, click on the CHOOSE FILE...
4. When a modal window appears, choose the firmware file and click on
the Open.
5. Next click on the UPDATE FIRMWARE button and upload the firmware image.
Wait for the router to flash and reboot.
OEM installation using the TFTP method (need level converter):
1. Download the latest firmware image.
2. Set up a Tftp server on a PC (e.g. Tftpd32) and place the firmware
image to the root directory of the server.
3. Power off the router and use a twisted pair cable to connect the PC
to any of the router's LAN ports.
4. Configure the network adapter of the PC to use IP address 192.168.0.180
and subnet mask 255.255.255.0.
5. Connect serial port (57600 8N1) and turn on the router.
6. Then interrupt "U-Boot Boot Menu" by hitting 2 key (select "2: Load
system code then write to Flash via TFTP.").
7. Press Y key when show "Warning!! Erase Linux in Flash then burn new
one. Are you sure? (Y/N)"
Input device IP (192.168.0.1) ==:192.168.0.1
Input server IP (192.168.0.180) ==:192.168.0.180
Input Linux Kernel filename () ==:firmware_name
The router should download the firmware via TFTP and complete flashing in
a few minutes.
After flashing is complete, use the PC to browse to http://192.168.1.1 or
ssh to proceed with the configuration.
Signed-off-by: Alexey Bartenev <41exey@proton.me>
(cherry picked from commit
ce998cb6e161db9c9e868fd570da9189f05fde3e)
Roland Reinl [Sun, 24 Dec 2023 13:42:23 +0000 (14:42 +0100)]
filogic: Add support for D-Link AQUILA PRO AI M30
Specification:
- MT7981 CPU using 2.4GHz and 5GHz WiFi (both AX)
- MT7531 switch
- 512MB RAM
- 128MB NAND flash with two UBI partitions with identical size
- 1 multi color LED (red, green, blue, white) connected via GCA230718
- 3 buttons (WPS, reset, LED on/off)
- 1 1Gbit WAN port
- 4 1Gbit LAN ports
Disassembly:
- There are four screws at the bottom: 2 under the rubber feets, 2 under the label.
- After removing the screws, the white plastic part can be shifted out of the blue part.
- Be careful because the antennas are mounted on the side and the top of the white part.
Serial Interface
- The serial interface can be connected to the 4 pin holes on the side of the board.
- Pins (from front to rear):
- 3.3V
- RX
- TX
- GND
- Settings: 115200, 8N1
MAC addresses:
- WAN MAC is stored in partition "Odm" at offset 0x81
- LAN (as printed on the device) is WAN MAC + 1
- WLAN MAC (2.4 GHz) is WAN MAC + 2
- WLAN MAC (5GHz) is WAN MAC + 3
Flashing via Recovery Web Interface:
- The recovery web interface always flashes to the currently active partition.
- If OpenWrt is flahsed to the second partition, it will not boot.
- Ensure that you have an OEM image available (encrypted and decrypted version). Decryption is described in the end.
- Set your IP address to 192.168.200.10, subnetmask 255.255.255.0
- Press the reset button while powering on the device
- Keep the reset button pressed until the LED blinks red
- Open a Chromium based and goto http://192.168.200.1 (recovery web interface)
- Download openwrt-mediatek-filogic-dlink_aquila-pro-ai-m30-a1-squashfs-recovery.bin
- The recovery web interface always reports successful flashing, even if it fails
- After flashing, the recovery web interface will try to forward the browser to 192.168.0.1 (can be ignored)
- If OpenWrt was flashed to the first partition, OpenWrt will boot (The status LED will start blinking white and stay white in the end). In this case you're done and can use OpenWrt.
- If OpenWrt was flashed to the second partition, OpenWrt won't boot (The status LED will stay red forever). In this case, the following steps are reuqired:
- Start the web recovery interface again and flash the **decrypted OEM image**. This will be flashed to the second partition as well. The OEM firmware web interface is afterwards accessible via http://192.168.200.1.
- Now flash the **encrypted OEM image** via OEM firmware web interface. In this case, the new firmware is flashed to the first partition. After flashing and the following reboot, the OEM firmware web interface should still be accessible via http://192.168.200.1.
- Start the web recovery interface again and flash the OpenWrt recovery image. Now it will be flashed to the first partition, OpenWrt will boot correctly afterwards and is accessible via 192.168.1.1.
Flashing via U-Boot:
- Open the case, connect to the UART console
- Set your IP address to 192.168.200.2, subnet mask 255.255.255.0. Connect to one of the LAN interfaces of the router
- Run a tftp server which provides openwrt-mediatek-filogic-dlink_aquila-pro-ai-m30-a1-initramfs-kernel.bin.
- Power on the device and select "7. Load image" in the U-Boot menu
- Enter image file, tftp server IP and device IP (if they differ from the default).
- TFTP download to RAM will start. After a few seconds OpenWrt initramfs should start
- The initramfs is accessible via 192.168.1.1, change your IP address accordingly (or use multiple IP addresses on your interface)
- Perform a sysupgrade using openwrt-mediatek-filogic-dlink_aquila-pro-ai-m30-a1-squashfs-sysupgrade.bin
- Reboot the device. OpenWrt should start from flash now
Revert back to stock using the Recovery Web Interface:
- Set your IP address to 192.168.200.2, subnetmask 255.255.255.0
- Press the reset button while powering on the device
- Keep the reset button pressed until the LED blinks red
- Open a Chromium based and goto http://192.168.200.1 (recovery web interface)
- Flash a decrypted firmware image from D-Link. Decrypting an firmware image is described below.
Decrypting a D-Link firmware image:
- Download https://github.com/RolandoMagico/firmware-utils/blob/M32/src/m32-firmware-util.c
- Compile a binary from the downloaded file, e.g. gcc m32-firmware-util.c -lcrypto -o m32-firmware-util
- Run ./m32-firmware-util M30 --DecryptFactoryImage <OriginalFirmware> <OutputFile>
- Example for firmware M30A1_FW101B05: ./m32-firmware-util M30 --DecryptFactoryImage M30A1_FW101B05\(
0725091522\).bin M30A1_FW101B05\(
0725091522\)_decrypted.bin
Flashing via OEM web interface is not possible, as it will change the active partition and OpenWrt is only running on the first UBI partition.
Controlling the LEDs:
- The LEDs are controlled by a chip called "GCA230718" which is connected to the main CPU via I2C (address 0x40)
- I didn't find any documentation or driver for it, so the information below is purely based on my investigations
- If there is already I driver for it, please tell me. Maybe I didn't search enough
- I implemented a kernel module (
leds-gca230718) to access the LEDs via DTS
- The LED controller supports PWM for brightness control and ramp control for smooth blinking. This is not implemented in the driver
- The LED controller supports toggling (on -> off -> on -> off) where the brightness of the LEDs can be set individually for each on cycle
- Until now, only simple active/inactive control is implemented (like when the LEDs would have been connected via GPIO)
- Controlling the LEDs requires three sequences sent to the chip. Each sequence consists of
- A reset command (0x81 0xE4) written to register 0x00
- A control command (for example 0x0C 0x02 0x01 0x00 0x00 0x00 0xFF 0x01 0x00 0x00 0x00 0xFF 0x87 written to register 0x03)
- The reset command is always the same
- In the control command
- byte 0 is always the same
- byte 1 (0x02 in the example above) must be changed in every sequence: 0x02 -> 0x01 -> 0x03)
- byte 2 is set to 0x01 which disables toggling. 0x02 would be LED toggling without ramp control, 0x03 would be toggling with ramp control
- byte 3 to 6 define the brightness values for the LEDs (R,G,B,W) for the first on cycle when toggling
- byte 7 defines the toggling frequency (if toggling enabled)
- byte 8 to 11 define the brightness values for the LEDs (R,G,B,W) for the second on cycle when toggling
- byte 12 is constant 0x87
Comparison to M32/R32:
- The algorithms for decrypting the OEM firmware are the same for M30/M32/R32, only the keys differ
- The keys are available in the GPL sources for the M32
- The M32/R32 contained raw data in the firmware images (kernel, rootfs), the R30 uses a sysupgrade tar instead
- Creation of the recovery image is quite similar, only the header start string changes. So mostly takeover from M32/R32 for that.
- Turned out that the bytes at offset 0x0E and 0x0F in the recovery image header are the checksum over the data area
- This checksum was not checked in the recovery web interface of M32/R32 devices, but is now active in R30
- I adapted the recovery image creation to also calculate the checksum over the data area
- The recovery image header for M30 contains addresses which don't match the memory layout in the DTS. The same addresses are also present in the OEM images
- The recovery web interface either calculates the correct addresses from it or has it's own logic to determine where which information must be written
Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
(cherry picked from commit
29cca6cfee4bc732f9bf7eca0cae9e56cd3c0f2f)
Roland Reinl [Sat, 30 Mar 2024 16:59:14 +0000 (17:59 +0100)]
mediatek: Moved recovery image creation to include/image-commands.mk
The recovery image is reqired for D-Link M30 as well. So I moved it to include/image-commands.mk to be able to use it for MT7622 and filogic devices.
Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
(cherry picked from commit
0e2b7e3bd674d2dd69ed8daf483cac5509cec9f0)
Roland Reinl [Tue, 26 Dec 2023 07:31:15 +0000 (08:31 +0100)]
filogic: Add LED driver for GCA230718
Add basic support for the LED driver for GCA230718.
- I didn't find any documentation or driver for it, so the information below is purely based on my investigations
- If there is already I driver for it, please tell me. Maybe I didn't search enough
- I implemented a kernel module (
leds-gca230718) to access the LEDs via DTS
- The LED controller supports PWM for brightness control and ramp control for smooth blinking. This is not implemented in the driver
- The LED controller supports toggling (on -> off -> on -> off) where the brightness of the LEDs can be set individually for each on cycle
- Until now, only simple active/inactive control is implemented (like when the LEDs would have been connected via GPIO)
- Controlling the LEDs requires three sequences sent to the chip. Each sequence consists of
- A reset command (0x81 0xE4) written to register 0x00
- A control command (for example 0x0C 0x02 0x01 0x00 0x00 0x00 0xFF 0x01 0x00 0x00 0x00 0xFF 0x87 written to register 0x03)
- The reset command is always the same
- In the control command
- byte 0 is always the same
- byte 1 (0x02 in the example above) must be changed in every sequence: 0x02 -> 0x01 -> 0x03)
- byte 2 is set to 0x01 which disables toggling. 0x02 would be LED toggling without ramp control, 0x03 would be toggling with ramp control
- byte 3 to 6 define the brightness values for the LEDs (R,G,B,W) for the first on cycle when toggling
- byte 7 defines the toggling frequency (if toggling enabled)
- byte 8 to 11 define the brightness values for the LEDs (R,G,B,W) for the second on cycle when toggling
- byte 12 is constant 0x87
Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
(cherry picked from commit
0682974aa8da4855ca373d195cb6365913fc1f8e)
Daniel Golle [Thu, 30 May 2024 13:38:56 +0000 (14:38 +0100)]
mediatek: filogic: avoid sub-shell invovation in netdev rename loop
Rename network devices to their label set in DT without invocation of
a sub-shell.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit
983222605ce6fabb036fbbd5797b6689ed082136)
Bjørn Mork [Thu, 18 May 2023 09:56:35 +0000 (11:56 +0200)]
mediatek: filogic: set wan label in preinit
Implement the functionality of
target/linux/ramips/patches-5.15/700-net-ethernet-mediatek-support-net-labels.patch
in userspace, since the driver patch has been rejected as a generic solution:
https://github.com/openwrt/openwrt/pull/11435
Signed-off-by: Bjørn Mork <bjorn@mork.no>
(cherry picked from commit
1dd1ac2c356ad37366dde64b624e5eb489b19393)
Hauke Mehrtens [Sun, 7 Jul 2024 21:25:22 +0000 (23:25 +0200)]
kernel: bump 5.15 to 5.15.162
Removed because they are upstream:
mediatek/patches-5.15/702-v5.17-net-mdio-add-helpers-to-extract-clause-45-regad-and-.patch
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=linux-5.15.y&id=
a03c3a34692f8400a85ec1cc2b058c6880bb7e7b
realtek/patches-5.15/020-v5.17-net-mdio-add-helpers-to-extract-clause-45-regad-and-.patch
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=linux-5.15.y&id=
a03c3a34692f8400a85ec1cc2b058c6880bb7e7b
Link: https://github.com/openwrt/openwrt/pull/15901
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Petr Štetiar [Mon, 4 Mar 2024 07:16:19 +0000 (07:16 +0000)]
linux-firmware: package Intel AX201 firmware
Alexander reported following:
iwlwifi 0000:00:14.3: Detected crf-id 0x3617, cnv-id 0x20000302 wfpm id 0x80000000
iwlwifi 0000:00:14.3: PCI dev a0f0/0074, rev=0x351, rfid=0x10a100
iwlwifi 0000:00:14.3: Direct firmware load for iwlwifi-QuZ-a0-hr-b0-77.ucode failed with error -2
It seems, that as of the current date, the highest firmware API version
supported by Linux 6.8-rc7 is still 77.
Closes: #14771
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit
8db83d4cc0fb4544ddec5fb50de73b8b4f64fb3d)
[Reduce to API version 72 for older mac80211]
Link: https://github.com/openwrt/openwrt/pull/15898
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Jordan Woyak [Tue, 26 Mar 2024 01:56:06 +0000 (20:56 -0500)]
config: Enable ext4 journaling by default.
Not having a journal by default is a major "gotcha".
Because openwrt does not fsck on boot, a power loss without journaling
can result in a dirty filesystem that openwrt will mount as read-only
which requires intervention to restore the router to working order.
Signed-off-by: Jordan Woyak <jordan.woyak@gmail.com>
(cherry picked from commit
f9f2426e398cf74d1098ae40317bfba677ac7560)
Link: https://github.com/openwrt/openwrt/pull/15898
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Felix Fietkau [Thu, 4 Apr 2024 11:45:33 +0000 (13:45 +0200)]
libxml2: add host build dependency on libiconv-full
Fixes build on macOS
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit
4ef13c4a49708d361df663a6e42e6e114a71c020)
Link: https://github.com/openwrt/openwrt/pull/15898
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Felix Fietkau [Wed, 10 Apr 2024 11:46:40 +0000 (13:46 +0200)]
hostapd: fix a crash corner case
On some setup failures, iface->bss can be NULL
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit
1ee5b7e506f937e16737472eed02bc5409716304)
Link: https://github.com/openwrt/openwrt/pull/15898
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sun, 21 Apr 2024 15:40:09 +0000 (17:40 +0200)]
mbedtls: Update to 2.28.8
This contains a fix for:
CVE-2024-28960: An issue was discovered in Mbed TLS 2.18.0 through 2.28.x
before 2.28.8 and 3.x before 3.6.0, and Mbed Crypto. The PSA Crypto
API mishandles shared memory.
(cherry picked from commit
360ac07eb933feaf29bb031f788f0bf81c473be7)
Link: https://github.com/openwrt/openwrt/pull/15898
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sun, 7 Apr 2024 20:46:13 +0000 (22:46 +0200)]
uencrypt: Fix compile warnings
keylen and ivlen are of type long and not size_t.
(cherry picked from commit
0fd9acb47165e9ef07b3fa0e4f381ebe5365464c)
Link: https://github.com/openwrt/openwrt/pull/15898
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Thomas Winkler [Fri, 10 Nov 2023 21:48:59 +0000 (22:48 +0100)]
base-files: fix uid/gid auto-enumeration to avoid 16-bit limit
uid/gid range should be limited to 16bit unsigned integer range to
avoid "wraparound" issues with permissions where jffs2
is employed for storage and chown 65536 (first auto-created user)
becomes equivalent to chown 0
Fixes: #13927
Signed-off-by: Thomas Winkler <tewinkler86@gmail.com>
(cherry picked from commit
140b48a9e93909873bee777ca5bdf49fe4f01271)
Link: https://github.com/openwrt/openwrt/pull/15898
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Rui Salvaterra [Wed, 8 May 2024 21:04:55 +0000 (22:04 +0100)]
linux-firmware: realtek: update rtl8821ae firmware
A newer version, rtl8821aefw_29.bin, has been available for over 7 years [1].
Let's use it.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit?id=
f70e4df2b384d21e36a7c30a591639592692e0ec
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
(cherry picked from commit
2b8e875a85802f6281df134e2231308f6c928796)
Link: https://github.com/openwrt/openwrt/pull/15898
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Sahil Dhiman [Sat, 25 May 2024 09:57:12 +0000 (15:27 +0530)]
scripts: Add GNU ftp mirror redirector for GNU and Savannah
Add GNU's redirector which automatically redirect user to nearby online
mirror.
Signed-off-by: Sahil Dhiman <sahil@hopbox.in>
Link: https://github.com/openwrt/openwrt/pull/15557
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit
6510eb3b5d612ea7a70c4a8d9b83639e3b46e221)
Link: https://github.com/openwrt/openwrt/pull/15898
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Fri, 31 May 2024 12:39:51 +0000 (14:39 +0200)]
tegra: Activate CONFIG_SND_DRIVERS
The option CONFIG_SND_DRIVERS is activated by default in the generic
configuration, do not deactivate it for tegra. This fixes the build of
the kmod-sound-dummy package on tegra.
(cherry picked from commit
21213c8156ccca90c135910b2ae2cdf40b8d98c3)
Link: https://github.com/openwrt/openwrt/pull/15898
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Qingfang Deng [Fri, 7 Jun 2024 09:55:38 +0000 (17:55 +0800)]
config: kernel: remove KASAN_EXTRA
The option has been removed from the kernel since 5.1.
Signed-off-by: Qingfang Deng <dqfext@gmail.com>
(cherry picked from commit
60ea3d6d46954553b7b50460dfe6b86878fe5990)
Link: https://github.com/openwrt/openwrt/pull/15898
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Daniel Golle [Mon, 10 Jun 2024 22:39:36 +0000 (23:39 +0100)]
mt76: mt7996: select required kernel and hostap options
Select DRIVER_11AX_SUPPORT and KERNEL_RELAY also for kmod-mt7996 to
prevent build failure if only this driver is selected during build and
end up with (most) required hostap features (IEEE 802.11be rates are not
yet supported).
Reported-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit
83311b747012e0675f96af18793e92cb8320c707)
Link: https://github.com/openwrt/openwrt/pull/15898
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Christian Lamparter [Sun, 2 Jun 2024 13:54:14 +0000 (15:54 +0200)]
firmware: intel-microcode: update to
20240531
Debian changelog:
intel-microcode (3.
20240531.1) unstable; urgency=medium
* New upstream microcode datafile
20240531
* Fix unspecified functional issues on Pentium Silver N/J5xxx,
Celeron N/J4xxx
* Updated Microcodes:
sig 0x000706a1, pf_mask 0x01, 2024-04-19, rev 0x0042, size 76800
* source: update symlinks to reflect id of the latest release,
20240531
-- Henrique de Moraes Holschuh <hmh@debian.org> Sat, 01 Jun 2024 11:49:47 -0300
intel-microcode (3.
20240514.1) unstable; urgency=medium
* New upstream microcode datafile
20240514
* Mitigations for INTEL-SA-01051 (CVE-2023-45733)
Hardware logic contains race conditions in some Intel Processors may
allow an authenticated user to potentially enable partial information
disclosure via local access.
* Mitigations for INTEL-SA-01052 (CVE-2023-46103)
Sequence of processor instructions leads to unexpected behavior in
Intel Core Ultra Processors may allow an authenticated user to
potentially enable denial of service via local access.
* Mitigations for INTEL-SA-01036 (CVE-2023-45745, CVE-2023-47855)
Improper input validation in some Intel TDX module software before
version 1.5.05.46.698 may allow a privileged user to potentially enable
escalation of privilege via local access.
* Fix for unspecified functional issues on 4th gen and 5th gen Xeon
Scalable, 12th, 13th and 14th gen Intel Core processors, as well as for
Core i3 N-series processors.
* Updated microcodes:
sig 0x000806f8, pf_mask 0x87, 2024-02-05, rev 0x2b0005c0, size 581632
sig 0x000806f7, pf_mask 0x87, 2024-02-05, rev 0x2b0005c0
sig 0x000806f6, pf_mask 0x87, 2024-02-05, rev 0x2b0005c0
sig 0x000806f5, pf_mask 0x87, 2024-02-05, rev 0x2b0005c0
sig 0x000806f4, pf_mask 0x87, 2024-02-05, rev 0x2b0005c0
sig 0x000806f8, pf_mask 0x10, 2024-02-05, rev 0x2c000390, size 614400
sig 0x000806f6, pf_mask 0x10, 2024-02-05, rev 0x2c000390
sig 0x000806f5, pf_mask 0x10, 2024-02-05, rev 0x2c000390
sig 0x000806f4, pf_mask 0x10, 2024-02-05, rev 0x2c000390
sig 0x00090672, pf_mask 0x07, 2023-12-05, rev 0x0035, size 224256
sig 0x00090675, pf_mask 0x07, 2023-12-05, rev 0x0035
sig 0x000b06f2, pf_mask 0x07, 2023-12-05, rev 0x0035
sig 0x000b06f5, pf_mask 0x07, 2023-12-05, rev 0x0035
sig 0x000906a3, pf_mask 0x80, 2023-12-05, rev 0x0433, size 222208
sig 0x000906a4, pf_mask 0x80, 2023-12-05, rev 0x0433
sig 0x000906a4, pf_mask 0x40, 2023-12-07, rev 0x0007, size 119808
sig 0x000b0671, pf_mask 0x32, 2024-01-25, rev 0x0123, size 215040
sig 0x000b06e0, pf_mask 0x11, 2023-12-07, rev 0x0017, size 138240
sig 0x000c06f2, pf_mask 0x87, 2024-02-05, rev 0x21000230, size 552960
sig 0x000c06f1, pf_mask 0x87, 2024-02-05, rev 0x21000230
* source: update symlinks to reflect id of the latest release,
20240514
-- Henrique de Moraes Holschuh <hmh@debian.org> Thu, 16 May 2024 21:40:52 -0300
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit
7d9b9762c95f5630857d8b08567fc1d72eb23217)
Link: https://github.com/openwrt/openwrt/pull/15898
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Rosen Penev [Fri, 14 Jun 2024 23:01:34 +0000 (16:01 -0700)]
tools/sparse: fix compilation with GCC14
Upstream backport.
Get rid of PKG_RELEASE as it's irrelevant to tools.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
(cherry picked from commit
253d777c968b8fd74e857bec4cd74267daae0010)
Link: https://github.com/openwrt/openwrt/pull/15898
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Christian Marangi [Mon, 17 Jun 2024 11:19:52 +0000 (13:19 +0200)]
scripts/ext-toolchain: add missing libc library specs
Add missing libc library spec that weren't added to the ext-toolchain
script when the library were introduced in the packages libs toolchain
Makefile.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit
8cad52a267bffe384a119f3e5ae1892e8580a981)
Link: https://github.com/openwrt/openwrt/pull/15898
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Felix Fietkau [Fri, 14 Jun 2024 12:43:39 +0000 (14:43 +0200)]
hostapd: fix crash on interface setup failure
Add a missing NULL pointer check when deleting beacons
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit
3984fb0582083c5c0f511ed3a33eb17908eccb08)
Link: https://github.com/openwrt/openwrt/pull/15898
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Felix Fietkau [Fri, 14 Jun 2024 12:17:57 +0000 (14:17 +0200)]
hostapd: use strdup on string passed to hostapd_add_iface
The data is modified within hostapd_add_iface
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit
032d3fcf7a861b140435b6507b2b0b66361c92f8)
Link: https://github.com/openwrt/openwrt/pull/15898
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Nathaniel Wesley Filardo [Thu, 20 Jun 2024 14:15:50 +0000 (15:15 +0100)]
kernel: crypto: remove FCRYPT from miscellany
It has its own dedicated knob
Signed-off-by: Nathaniel Wesley Filardo <nwfilardo@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15761
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit
7d71c03ab188a58d74d6cdbeabb38b70ead2c74b)
Link: https://github.com/openwrt/openwrt/pull/15898
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sat, 29 Jun 2024 16:23:13 +0000 (18:23 +0200)]
kernel: Add kmod-mfd
Package the mfd-core.ko kernel module. It is selected by the
kmod-hwmon-gsc already.
Link: https://github.com/openwrt/openwrt/pull/15833
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit
8b4fd1c0dece936dc2c79f2a17d824512e7e7df3)
Link: https://github.com/openwrt/openwrt/pull/15898
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sat, 29 Jun 2024 16:14:47 +0000 (18:14 +0200)]
kernel: Add kmod-crypto-xxhash
kxxhash_generic.ko is a soft dependency of kmod-fs-btrfs, but we did not
package it. Extract the kmod-lib-xxhash and then package
xxhash_generic.ko.
Link: https://github.com/openwrt/openwrt/pull/15833
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit
2ebeda029490e308cc0e8f475e63280f960e74c4)
Link: https://github.com/openwrt/openwrt/pull/15898
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sat, 29 Jun 2024 15:38:46 +0000 (17:38 +0200)]
kernel: Add kmod-crypto-blake2b
The kmod-fs-btrfs package has a soft dependency to kmod-crypto-blake2b
The CONFIG_BTRFS_FS kernel build option selects CONFIG_CRYPTO_BLAKE2B,
but we did not package it before.
Link: https://github.com/openwrt/openwrt/pull/15833
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit
f89091bba6be483e66c5ac14c477621f74aef203)
Link: https://github.com/openwrt/openwrt/pull/15898
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sat, 29 Jun 2024 15:54:49 +0000 (17:54 +0200)]
kernel: Fix kmod-lib-lz4 packaging
The kernel provides two variants of the lz4 compression a normal version
and a high compression mode version. The old kmod-lib-lz4 package
contained the normal version plus one part of the lz4hc version. There
was already code which selected the kmod-lib-lz4hc package which did
not exists.
I split this into 3 packages. kmod-lib-lz4 and kmod-lib-lz4hc for the
normal the and high compression algorithm which contain the specific
code and the kmod-lib-lz4-decompress which contains the common
decompressor.
New we are also packaging lz4hc.ko
Link: https://github.com/openwrt/openwrt/pull/15833
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit
fac507606d75eec04762013582273468eea7ed92)
Link: https://github.com/openwrt/openwrt/pull/15898
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sat, 29 Jun 2024 15:24:09 +0000 (17:24 +0200)]
kernel: Extract kmod-nf-dup-inet
The nf_dup_ipv4.ko and nf_dup_ipv6.ko kernel module were packaged by
kmod-ipt-tee and kmod-nft-dup-inet at the same time. Extract them into a
separate package used by both.
Link: https://github.com/openwrt/openwrt/pull/15833
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit
b0953c4fbf1bb0ad0844febe991636d05884c194)
Link: https://github.com/openwrt/openwrt/pull/15898
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Paweł Owoc [Mon, 18 Mar 2024 20:53:51 +0000 (21:53 +0100)]
mac80211: add missing config for third 160MHz width for 5GHz radio
Without this configuration it is not possible to run the radio using HE160 on channels 149-177.
Fixes: #14906
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
(cherry picked from commit
a91b79fd04d58e711273d08e0b1246942b2eec98)
Link: https://github.com/openwrt/openwrt/pull/15898
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Felix Fietkau [Tue, 11 Jul 2023 12:38:06 +0000 (14:38 +0200)]
mac80211: add fix for receiving STP frames on mesh
Fix length in ethernet header
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit
8f7be2a2ba79987bd150f5f4e266daf96fd94e32)
Link: https://github.com/openwrt/openwrt/pull/15898
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Oldřich Jedlička [Fri, 6 Oct 2023 21:37:47 +0000 (23:37 +0200)]
mac80211: fix flush during station removal
This fixes WARN_ONs when using AP_VLANs after station removal. The flush
call passed AP_VLAN vif to driver, but because these vifs are virtual and
not registered with drivers, we need to translate to the correct AP vif
first.
Fixes: openwrt#12420
Signed-off-by: Oldřich Jedlička <oldium.pro@gmail.com>
[Rename to 360-wifi-mac80211-do-not-pass-ap_vlan-vif-pointer-to-dri.patch]
(cherry picked from commit
3e738781a9712eaa81d5af0ecc8b55cbfe480c68)
Link: https://github.com/openwrt/openwrt/pull/15898
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
David Bauer [Sat, 22 Jul 2023 15:40:56 +0000 (17:40 +0200)]
mediatek: add missing SPDX header
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit
36f7ececc21fe6698a75f5ce9fc3ebf6c96a1b97)
Chukun Pan [Fri, 3 Nov 2023 15:02:35 +0000 (23:02 +0800)]
mediatek: filogic: add Netcore N60 support
Hardware specification:
SoC: MediaTek MT7986A 4x A53
Flash: ESMT F50L1G41LB 128MB
RAM: W632GU6NB DDR3 256MB
Ethernet: 1x 2.5G + 4x 1G
WiFi1: MT7975N 2.4GHz 4T4R
WiFi2: MT7975PN 5GHz 4T4R
Button: Reset, WPS
Power: DC 12V 2A
Flash instructions:
1. Connect to the router using ssh or telnet,
username: useradmin, password is the web
login password of the router.
2. Use scp to upload bl31-uboot.fip and flash:
"mtd write xxx-preloader.bin spi0.0"
"mtd write xxx-bl31-uboot.fip FIP"
"mtd erase ubi"
3. Connect to the router via the Lan port,
set a static ip of your PC.
(ip 192.168.1.254, gateway 192.168.1.1)
4. Download initramfs image, reboot router,
waiting for tftp recovery to complete.
5. After openwrt boots up, perform sysupgrade.
Note:
1. Back up all mtd partitions before flashing.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
(cherry picked from commit
4ae474afbd023a3386f4276ca8f948a44b49ff1b)
Chukun Pan [Thu, 2 Nov 2023 15:16:28 +0000 (23:16 +0800)]
uboot-mediatek: add Netcore N60 support
The vendor uboot requires special fit verification.
So add a custom uboot build for this device.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
(cherry picked from commit
0170666d89127585d30c3f1a8fdf641d9e8fbbbf)
Tianling Shen [Wed, 1 Nov 2023 06:46:15 +0000 (14:46 +0800)]
mediatek: add support for JDCloud RE-CP-03
Hardware specification:
SoC: MediaTek MT7986A 4x A53
Flash: 128GB eMMC
RAM: 1GB DDR4
Ethernet: 4x 1GbE, 1x 2.5GbE (RTL8221B)
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset, Joylink
Power: DC 12V 2A
Flash instructions:
1. Download and flash the vendor migration firmware via webUI:
https://firmware.download.immortalwrt.eu.org/cnsztl/mediatek/filogic/openwrt-mediatek-mt7986-jdcloud_re-cp-03-vendor-migration.bin
(Default address is 192.168.68.1, user root, no password)
2. After device has booted up, write new GPT table:
dd if=openwrt-mediatek-filogic-jdcloud_re-cp-03-gpt.bin of=/dev/mmcblk0 bs=512 seek=0 count=34 conv=fsync
3. Erase and write new BL2:
echo 0 > /sys/block/mmcblk0boot0/force_ro
dd if=/dev/zero of=/dev/mmcblk0boot0 bs=512 count=8192 conv=fsync
dd if=openwrt-mediatek-filogic-jdcloud_re-cp-03-preloader.bin of=/dev/mmcblk0boot0 bs=512 conv=fsync
4. Erase and write new FIP:
dd if=/dev/zero of=/dev/mmcblk0 bs=512 seek=13312 count=8192 conv=fsync
dd if=openwrt-mediatek-filogic-jdcloud_re-cp-03-bl31-uboot.fip of=/dev/mmcblk0 bs=512 seek=13312 conv=fsync
5. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
6. Serve OpenWrt initramfs image using TFTP server.
7. Cut off the power and re-engage, wait for TFTP recovery to complete.
8. After OpenWrt has booted, perform sysupgrade.
9. Additionally, if you want to have eMMC recovery boot feature:
(Don't worry! You will always have TFTP recovery boot feature.)
dd if=openwrt-mediatek-filogic-jdcloud_re-cp-03-initramfs-recovery.itb of=/dev/mmcblk0p4 bs=512 conv=fsync
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit
c0c3234e17207a9287a08757fc1752490144a1cd)
Tianling Shen [Wed, 1 Nov 2023 06:44:50 +0000 (14:44 +0800)]
uboot-mediatek: add support for JDCloud RE-CP-03
The vendor U-Boot has enabled signature verification, so add
a custom U-Boot build for OpenWrt.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit
6fa4fbbc5293886aa6bae6e0cac4b99a4c472fc4)
Luis Mita [Thu, 6 Jun 2024 20:43:19 +0000 (16:43 -0400)]
ramips: mt76x8: sync Cudy TR1200 v1 naming
Cudy assigns hardware versions to its devices on its website, and
the Cudy TR1200 router is now Cudy TR1200 v1.
OpenWrt currently uses both variants, and this commit removes
inconsistencies using only the new name.
Signed-off-by: Luis Mita <luis@luismita.com>
(cherry picked from commit
d780d530dd89d135fffc6fb6598e6f7b28cd3921)
Link: https://github.com/openwrt/openwrt/pull/15875
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Luis Mita [Thu, 30 May 2024 18:50:23 +0000 (14:50 -0400)]
ramips: mt76x8: add support for Cudy TR1200 v1
Hardware:
- SoC: MediaTek MT7628AN (MIPS 580MHz)
- Flash: 16 MiB XMC 25QH128CH10
- RAM: 128 MiB ESMT M14D1G1664A
- WLAN: 2.4 GHz (MT7628), 5 GHz (MT7613BEN 802.11ac)
- Ethernet: 1x 10/100 Mbps WAN, 1x 10/100 LAN (MT7628)
- USB 2.0 port
- Buttons: 1 Reset button, 1 slider button
- LEDs: 1x Red, 1x White
- Serial console: unpopulated header, 115200 8n1
- Power: 5 VDC, 2 A
MAC addresses:
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| WAN | 80:af:ca:xx:xx:x0 | label |
| LAN | 80:af:ca:xx:xx:x0 | label |
| WLAN 2g | 80:af:ca:xx:xx:x0 | label |
| WLAN 5g | 80:af:ca:xx:xx:x2 | label+2 |
+---------+-------------------+-----------+
Installation:
The installation must be done via TFTP by disassembling the router.
On other occasions Cudy has distributed intermediate firmware to make
installation easier, and so I recommend checking the Wiki for this
device if there is a more convenient solution than the one below.
To install using TFTP:
1. Upgrade to a beta firmware (signed by Cudy) that can be downloaded
from the wiki. This is required in order to use an unlocked u-boot.
2. Connect to UART.
3. While the router is turning on, press 1.
4. Connect to LAN and set your IP to 192.168.1.88/24. Configure a TFTP
server and an OpenWrt initramfs-kernel.bin firmware file as recovery.bin.
5. Press Enter three times. Verify the filename.
6. If you can reach LuCI or SSH now, just use the sysupgrade image with
the 'Keep settings' option turned off.
If you don't want to use the beta firmware nor the unlocked u-boot, you
can install the firmware writing the sysupgrade image on the firmware
partition of the SPI flash.
Signed-off-by: Luis Mita <luis@luismita.com>
(cherry picked from commit
f1091ef7ac3596f1e401b918a36273672acbe389)
Link: https://github.com/openwrt/openwrt/pull/15875
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sun, 7 Jul 2024 19:56:12 +0000 (21:56 +0200)]
mt76: Fix PKG_MIRROR_HASH
The PKG_MIRROR_HASH was updated to a wrong version.
Fixes: f64576f367eb ("mt76: update to Git HEAD (2024-04-03)")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Thu, 27 Jun 2024 23:32:46 +0000 (01:32 +0200)]
mac80211: Update to version 6.1.97-1
This updates mac80211 to version 6.1.97-1. This code is based on Linux
6.1.97 and contains all fixes included in the upstream wireless
subsystem from that kernel version. This includes many bugfixes and also
some security fixes.
The removed patches are already integrated in upstream Linux 6.1.97 or
in backports.
The following patches were integrated in upstream Linux:
ath11k/0013-wifi-ath11k-synchronize-ath11k_mac_he_gi_to_nl80211_.patch
ath11k/0035-wifi-ath11k-Use-platform_get_irq-to-get-the-interrup.patch
ath11k/0036-wifi-ath11k-fix-SAC-bug-on-peer-addition-with-sta-ba.patch
ath11k/0047-wifi-ath11k-fix-deinitialization-of-firmware-resourc.patch
ath11k/0053-wifi-ath11k-fix-writing-to-unintended-memory-region.patch
ath11k/0060-wifi-ath11k-Ignore-frags-from-uninitialized-peer-in-.patch
ath11k/0065-wifi-ath11k-fix-tx-status-reporting-in-encap-offload.patch
ath11k/0067-wifi-ath11k-Fix-SKB-corruption-in-REO-destination-ri.patch
ath11k/0069-wifi-ath11k-fix-registration-of-6Ghz-only-phy-withou.patch
ath11k/0080-wifi-ath11k-add-support-default-regdb-while-searchin.patch
ath11k/0085-wifi-ath11k-fix-memory-leak-in-WMI-firmware-stats.patch
ath11k/0086-wifi-ath11k-Add-missing-check-for-ioremap.patch
ath11k/0096-wifi-ath11k-fix-boot-failure-with-one-MSI-vector.patch
subsys/337-wifi-mac80211-fix-race-condition-on-enabling-fast-xm.patch
The following patches were integrated in upstream backports:
ath11k/901-wifi-ath11k-pci-fix-compilation-in-5.16-and-older.patch
build/080-resv_start_op.patch
build/110-backport_napi_build_skb.patch
The following files are missing in backports, we do not have to remove
them any more. Some were already missing before some were removed in
this update:
include/linux/cordic.h
include/linux/crc8.h
include/linux/eeprom_93cx6.h
include/linux/wl12xx.h
include/net/ieee80211.h
backport-include/linux/bcm47xx_nvram.h
include/linux/ath9k_platform.h
include/net/bluetooth/
backports ships a dummy Mediatek wed header for older kernel versions.
We backported the feature in our kernel, remove the dummy header:
backport-include/linux/soc/mediatek/mtk_wed.h
Remove header files for subsystems used form the mainline kernel:
include/trace/events/qrtr.h
include/net/rsi_91x.h
backport-include/linux/platform_data/brcmnand.h
Link: https://github.com/openwrt/openwrt/pull/15827
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Mon, 1 Jul 2024 21:55:03 +0000 (23:55 +0200)]
iw: sync nl80211.h
Update the nl80211.h file in iw with the version from backports.
The files were out of sync already before the mac80211 update. If iw set
the NL80211_ATTR_WIPHY_ANTENNA_GAIN attribute the kernel assumed it set
the NL80211_ATTR_PUNCT_BITMAP attribute because the id was the same.
Link: https://github.com/openwrt/openwrt/pull/15827
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Lu jicong [Tue, 2 Jul 2024 13:01:49 +0000 (21:01 +0800)]
target.mk: fix arm architecture level detection
Now kernel configs of armv6k CPUs don't include CONFIG_CPU_V6.
So armv6k CPUs cannot be detected as arm_v6.
Fix this by adding detection for CONFIG_CPU_V6K.
Signed-off-by: Lu jicong <jiconglu58@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15855
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit
d55083fbcaea9cdd2ebc10a2d38989ad485a5357)
Mathew McBride [Tue, 28 May 2024 23:09:17 +0000 (09:09 +1000)]
armsr: add realtek and smsc ethernet phy drivers to the default image
This adds two more common PHY brands to the image.
Realtek is used on the Google Coral "Phanbell" board (i.MX8MQ).
SMSC has been used on various Raspberry Pi boards.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
(cherry picked from commit
bcbdde00c3a81a53d11ddc6101517185ae426691)
Link: https://github.com/openwrt/openwrt/pull/15808
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Mathew McBride [Sun, 26 May 2024 04:12:58 +0000 (14:12 +1000)]
armsr: enable framebuffer emulation for virtio-gpu/drm displays
This was discovered when trying to run OpenWrt on Hetzner Cloud's
Arm-based instances.
Hetzner uses QEMU/KVM with virtio-gpu as the main display device,
together with an ACPI firmware. This was not displaying a console
previously.
This setup can be emulated by qemu using options below:
qemu-system-aarch64 \
-machine virt \
-bios QEMU_EFI.fd \
-device virtio-gpu \
-usb \
-device qemu-xhci,id=xhci \
-device usb-tablet,bus=xhci.0 \
-device usb-kbd,bus=xhci.0 \
-vnc :0
Signed-off-by: Mathew McBride <matt@traverse.com.au>
(cherry picked from commit
ea7383e7215c36e47a769f34c57aa458300b8bc2)
Link: https://github.com/openwrt/openwrt/pull/15808
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
John Vincent [Fri, 31 May 2024 13:56:24 +0000 (14:56 +0100)]
kernel: armsr: Renesas: RZ: Ethernet module and ttySC0
Ethernet module enable for Renesas RZ platform
inittab fix for ttySC0
Fixes: #15284
Signed-off-by: John Vincent <john.vincent.xa@bp.renesas.com>
(cherry picked from commit
531b3f667c40405581a398a9648a0e6c27909a87)
Link: https://github.com/openwrt/openwrt/pull/15808
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Mathew McBride [Tue, 30 Apr 2024 02:34:37 +0000 (12:34 +1000)]
armsr: armv8: enable serial console for Renesas platforms
Support for Renesas Arm families was added in commit
1ff4f4df2301
("armsr: armv8: enable CONFIG_ARCH_RENESAS"), but this did not
enable the console/tty hardware for these SoCs, which is derived
from the SuperH family (CONFIG_SERIAL_SH_SCI).
Link: https://github.com/openwrt/openwrt/issues/15284
Signed-off-by: Mathew McBride <matt@traverse.com.au>
(cherry picked from commit
683355d0a6d51cbeda258492bc16a9c6413b387e)
Link: https://github.com/openwrt/openwrt/pull/15808
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Roland Reinl [Sun, 12 Nov 2023 18:04:32 +0000 (19:04 +0100)]
mediatek: Add support for D-Link EAGLE PRO AI R32
R32 is like the M32 part of the EAGLE PRO AI series from D-Link.
Specification:
- MT7622BV SoC with 2.4GHz wifi
- MT7975AN + MT7915AN for 5GHz
- MT7531BE Switch
- 512MB RAM
- 128 MB flash
- 2 LEDs (Status and Internet, both can be either orange or white)
- 2 buttons (WPS and Reset)
Compared to M32, the R32 has the following differences:
- 4 LAN ports instead of 2
- The recory image starts with DLK6E6015001 instaed of DLK6E6010001
- Individual LEDs for power and internet
- MAC address is stored at another offset in the ODM partition
MAC addresses:
- WAN MAC is stored in partition "Odm" at offset 0x81
- LAN (as printed on the device) is WAN MAC + 1
- WLAN MAC (2.4 GHz) is WAN MAC + 2
- WLAN MAC (5GHz) is WAN MAC + 3
Flashing via Recovery Web Interface:
- Set your IP address to 192.168.0.10, subnetmask 255.255.255.0
- Press the reset button while powering on the deivce
- Keep the reset button pressed until the internet LED blinks fast
- Open a Chromium based and goto http://192.168.0.1
- Download openwrt-mediatek-mt7622-dlink_eagle-pro-ai-r32-a1-squashfs-recovery.bin
Flashing via uBoot:
- Open the case, connect to the UART console
- Set your IP address to 10.10.10.3, subnet mask 255.255.255.0. Connect to one of the LAN interfaces of the router
- Run a tftp server which provides openwrt-mediatek-mt7622-dlink_eagle-pro-ai-r32-initramfs-kernel.bin.
- You can rename the file to iverson_uImage (no extension), then you don't have to enter the whole file name in uboot later.
- Power on the device and select "1. System Load Linux to SDRAM via TFTP." in the boot menu
- Enter image file, tftp server IP and device IP (if they differ from the default).
- TFTP download to RAM will start. After a few seconds OpenWrt initramfs should start
- The initramfs is accessible via 192.168.1.1, change your IP address accordingly (or use multiple IP addresses on your interface)
- Create a backup of the Kernel1 partition, this file is required if a revert to stock should be done later
- Perform a sysupgrade using openwrt-mediatek-mt7622-dlink_eagle-pro-ai-r32-squashfs-sysupgrade.bin
- Reboot the device. OpenWrt should start from flash now
Revert back to stock using the Recovery Web Interface:
- Set your IP address to 192.168.0.10, subnetmask 255.255.255.0
- Press the reset button while powering on the deivce
- Keep the reset button pressed until the internet LED blinks fast
- Open a Chromium based and goto http://192.168.0.1
- Flash a decrypted firmware image from D-Link. Decrypting an firmware image is described below.
Decrypting a D-Link firmware image:
- Download https://github.com/RolandoMagico/firmware-utils/blob/M32/src/m32-firmware-util.c
- Compile a binary from the downloaded file, e.g. gcc m32-firmware-util.c -lcrypto -o m32-firmware-util
- Run ./m32-firmware-util R32 --DecryptFactoryImage <OriginalFirmware> <OutputFile>
- Example for firmware R32A1_FW103B01: ./m32-firmware-util R32 --DecryptFactoryImage R32A1_FW103B01.bin R32A1_FW103B01.decrypted.bin
Revert back to stock using uBoot:
- Open the case, connect to the UART console
- Set your IP address to 10.10.10.3, subnet mask 255.255.255.0. Connect to one of the LAN interfaces of the router
- Run a tftp server which provides the previously created backup of the Kernel1 partition.
- You can rename the file to iverson_uImage (no extension), then you don't have to enter the whole file name in uboot later.
- Power on the device and select "2. System Load Linux Kernel then write to Flash via TFTP." in the boot menu
- Enter image file, tftp server IP and device IP (if they differ from the default).
- TFTP download to FLASH will start. After a few seconds the stock firmware should start again
There is also an image openwrt-mediatek-mt7622-dlink_eagle-pro-ai-r32-a1-squashfs-tftp.bin which can directly be flashed via U-Boot and TFTP.
It can be used if no backup of the Kernel1 partition is reuqired.
Flahsing via OEM web interface is currently not possible, the OEM images are encrypted. Creating images is only possible manually at the moment.
The support for the M32/R32 already includes support for flashing from the OEM web interface:
- The device tree contains both partitions (Kernel1 and Kernel2) with conditions to select the correct one based on the kernel command line
- The U-Boot variable "boot_part" is set accordingly during startup to finish the partition swap after flashing from the OEM web interface
- OpenWrt sysupgrade flashing always uses the partition where it was initially flashed to (no partition swap)
Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
(cherry picked from commit
fdb87a91b4202ad1a58fe46f499e4e68bf82de4e)
Link: https://github.com/openwrt/openwrt/pull/15776
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fabrice Fontaine [Sat, 27 Apr 2024 15:50:05 +0000 (17:50 +0200)]
package/utils/secilc: drop PKG_CPE_ID
cpe:/a:selinuxproject:secilc is not a correct CPE ID for secilc:
https://nvd.nist.gov/products/cpe/search/results?keyword=cpe:2.3:a:selinuxproject:secilc
Fixes: 9ee7c1ec60e23f25f5d275c6439ce93aec914e1c (secilc: adds new package)
Signed-off-by: Fabrice Fontaine <fontaine.fabrice@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15298
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit
58a5877846e2913bed4fd982386797d7751f58f0)
Link: https://github.com/openwrt/openwrt/pull/15881
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fabrice Fontaine [Sat, 27 Apr 2024 15:25:58 +0000 (17:25 +0200)]
package/network/utils/iptables: fix PKG_CPE_ID
cpe:/a:netfilter:iptables is the correct CPE ID for iptables:
https://nvd.nist.gov/products/cpe/search/results?keyword=cpe:2.3:a:netfilter:iptables
Fixes: c61a2395140d92cdd37d3d6ee43a765427e8e318 (add PKG_CPE_ID ids to package and tools)
Signed-off-by: Fabrice Fontaine <fontaine.fabrice@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15297
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit
6e5edec159e2dc468607a5b9179f722857a38421)
Link: https://github.com/openwrt/openwrt/pull/15881
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fabrice Fontaine [Fri, 26 Apr 2024 15:47:24 +0000 (17:47 +0200)]
package/libs/libjson-c: fix PKG_CPE_ID
cpe:/a:json-c:json-c is the correct CPE ID for libjson-c:
https://nvd.nist.gov/products/cpe/search/results?keyword=cpe:2.3:a:json-c:json-c
Fixes: c61a2395140d92cdd37d3d6ee43a765427e8e318 (add PKG_CPE_ID ids to package and tools)
Signed-off-by: Fabrice Fontaine <fontaine.fabrice@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15292
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit
a4f723e04ed245819fe320f472a4ff2b4eda00fb)
Link: https://github.com/openwrt/openwrt/pull/15881
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fabrice Fontaine [Fri, 26 Apr 2024 14:09:32 +0000 (16:09 +0200)]
package/network/services/dropbear: fix PKG_CPE_ID
cpe:/a:dropbear_ssh_project:dropbear_ssh is the correct CPE ID for dropbear:
https://nvd.nist.gov/products/cpe/search/results?keyword=cpe:2.3:a:dropbear_ssh_project:dropbear_ssh
Fixes: c61a2395140d92cdd37d3d6ee43a765427e8e318 (add PKG_CPE_ID ids to package and tools)
Signed-off-by: Fabrice Fontaine <fontaine.fabrice@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15290
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit
289f811abb4ace7aa08ae7bf85c0d4f9460f0802)
Link: https://github.com/openwrt/openwrt/pull/15881
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fabrice Fontaine [Fri, 26 Apr 2024 08:41:15 +0000 (10:41 +0200)]
toolchain/nasm: fix PKG_CPE_ID
cpe:/a:nasm:netwide_assembler is the correct CPE ID for nasm:
https://nvd.nist.gov/products/cpe/search/results?keyword=cpe:2.3:a:nasm:netwide_assembler
Fixes: bcf02c5d3123a99c717ca33f1d7c6250acf0f33f (toolchain: assign PKG_CPE_ID)
Signed-off-by: Fabrice Fontaine <fontaine.fabrice@gmail.com>
(cherry picked from commit
e1ca08518e96ccf088119fbc9930c5e4beef86cc)
Link: https://github.com/openwrt/openwrt/pull/15881
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fabrice Fontaine [Fri, 26 Apr 2024 08:51:16 +0000 (10:51 +0200)]
tools/flex: fix PKG_CPE_ID
cpe:/a:westes:flex is the correct CPE ID for flex:
https://nvd.nist.gov/products/cpe/search/results?keyword=cpe:2.3:a:westes:flex
Fixes: c61a2395140d92cdd37d3d6ee43a765427e8e318 (add PKG_CPE_ID ids to package and tools)
Signed-off-by: Fabrice Fontaine <fontaine.fabrice@gmail.com>
(cherry picked from commit
832460b452d840451adf44713e90515fc61c88ab)
Link: https://github.com/openwrt/openwrt/pull/15881
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fabrice Fontaine [Fri, 26 Apr 2024 08:59:58 +0000 (10:59 +0200)]
tools/zlib: fix PKG_CPE_ID
cpe:/a:zlib:zlib is the correct CPE ID for zlib:
https://nvd.nist.gov/products/cpe/search/results?keyword=cpe:2.3:a:zlib:zlib
Fixes: c61a2395140d92cdd37d3d6ee43a765427e8e318 (add PKG_CPE_ID ids to package and tools)
Signed-off-by: Fabrice Fontaine <fontaine.fabrice@gmail.com>
(cherry picked from commit
e9ecaade6f1f9bd821523a3b731bfaaf5ab5ca35)
Link: https://github.com/openwrt/openwrt/pull/15881
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fabrice Fontaine [Fri, 26 Apr 2024 13:09:50 +0000 (15:09 +0200)]
package/libs/pcre2: fix PKG_CPE_ID
cpe:/a:pcre:pcre2 is the correct CPE ID for pcre2:
https://nvd.nist.gov/products/cpe/search/results?keyword=cpe:2.3:a:pcre:pcre2
Fixes: c39b0646f3f2d96d40f601209859175af8537b6d (pcre2: import pcre2 from packages feed)
Signed-off-by: Fabrice Fontaine <fontaine.fabrice@gmail.com>
(cherry picked from commit
27d1ebb46adfd58db9a8034336c2d85b41f617f9)
Link: https://github.com/openwrt/openwrt/pull/15881
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Sean Khan [Sun, 9 Jun 2024 01:02:30 +0000 (21:02 -0400)]
openssl: conditionally disable engine section
Currently, the build option to enable/disable engine support isn't
reflected in the final '/etc/ssl/openssl.cnf' config. It assumes `engines`
is always enabled, producing an error whenever running any
commands in openssl util or programs that explicitly use settings
from '/etc/ssl/openssl.cnf'.
```
➤ openssl version
FATAL: Startup failure (dev note: apps_startup()) for openssl
307D1EA97F000000:error:
12800067:lib(37):dlfcn_load:reason(103):crypto/dso/dso_dlfcn.c:118:filename(libengines.so):
Error loading shared library libengines.so: No such file or directory
307D1EA97F000000:error:
12800067:lib(37):DSO_load:reason(103):crypto/dso/dso_lib.c:152:
307D1EA97F000000:error:
0700006E:lib(14):module_load_dso:reason(110):crypto/conf/conf_mod.c:321:module=engines, path=engines
307D1EA97F000000:error:
07000071:lib(14):module_run:reason(113):crypto/conf/conf_mod.c:266:module=engines
```
Build should check for the `CONFIG_OPENSSL_ENGINE` option, and comment out `engines`
if not explicitly enabled.
Example:
```
[openssl_init]
providers = provider_sect
```
After this change, openssl util works correctly.
```
➤ openssl version
OpenSSL 3.0.14 4 Jun 2024 (Library: OpenSSL 3.0.14 4 Jun 2024)
```
Signed-off-by: Sean Khan <datapronix@protonmail.com>
Link: https://github.com/openwrt/openwrt/pull/15661
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit
31ec4515c3c14704d669156d87e2af5eeb5420e4)
Link: https://github.com/openwrt/openwrt/pull/15873
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
John Audia [Wed, 5 Jun 2024 19:55:29 +0000 (15:55 -0400)]
openssl: update to 3.0.14
Major changes between OpenSSL 3.0.13 and OpenSSL 3.0.14 [04-Jun-2024]
* Fixed potential use after free after SSL_free_buffers() is called.
[CVE-2024-4741]
* Fixed checking excessively long DSA keys or parameters may be very slow.
[CVE-2024-4603]
* Fixed an issue where some non-default TLS server configurations can cause
unbounded memory growth when processing TLSv1.3 sessions. An attacker may
exploit certain server configurations to trigger unbounded memory growth that
would lead to a Denial of Service. [CVE-2024-2511]
* New atexit configuration switch, which controls whether the OPENSSL_cleanup
is registered when libcrypto is unloaded. This can be used on platforms
where using atexit() from shared libraries causes crashes on exit
Signed-off-by: John Audia <therealgraysky@proton.me>
Build system: x86/64
Build-tested: x86/64/AMD Cezanne
(cherry picked from commit
bac2f1bed6db5da166aad7b1091c2e9af0ffef5d)
Link: https://github.com/openwrt/openwrt/pull/15873
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sun, 21 Apr 2024 15:46:55 +0000 (17:46 +0200)]
wolfssl: Update to 5.7.0
This fixes multiple security problems:
* [High] CVE-2024-0901 Potential denial of service and out of bounds
read. Affects TLS 1.3 on the server side when accepting a connection
from a malicious TLS 1.3 client. If using TLS 1.3 on the server side
it is recommended to update the version of wolfSSL used.
* [Med] CVE-2024-1545 Fault Injection vulnerability in
RsaPrivateDecryption function that potentially allows an attacker
that has access to the same system with a victims process to perform
a Rowhammer fault injection. Thanks to Junkai Liang, Zhi Zhang, Xin
Zhang, Qingni Shen for the report (Peking University, The University
of Western Australia)."
* [Med] Fault injection attack with EdDSA signature operations. This
affects
ed25519 sign operations where the system could be susceptible
to Rowhammer attacks. Thanks to Junkai Liang, Zhi Zhang, Xin Zhang,
Qingni Shen for the report (Peking University, The University of
Western Australia).
Size increased a little:
wolfssl 5.6.6:
516880 bin/packages/mips_24kc/base/libwolfssl5.6.6.e624513f_5.6.6-stable-r1_mips_24kc.ipk
wolfssl: 5.7.0:
519429 bin/packages/mips_24kc/base/libwolfssl5.7.0.e624513f_5.7.0-stable-r1_mips_24kc.ipk
(cherry picked from commit
f475a44c03a303851959930030ab9e6acebb81a7)
Link: https://github.com/openwrt/openwrt/pull/15872
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Nick Hainke [Wed, 27 Dec 2023 13:21:46 +0000 (14:21 +0100)]
wolfssl: update to 5.6.6
Release Notes:
https://github.com/wolfSSL/wolfssl/releases/tag/v5.6.6-stable
Refresh patches:
- 100-disable-hardening-check.patch
Fixes: CVE-2023-6935 CVE-2023-6936 CVE-2023-6937
Signed-off-by: Nick Hainke <vincent@systemli.org>
(cherry picked from commit
511578c128121326a3c48fdb35e4e62f96dc7b9d)
Link: https://github.com/openwrt/openwrt/pull/15872
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
David Bentham [Fri, 10 Nov 2023 18:50:38 +0000 (18:50 +0000)]
mediatek: add Comfast CF-E393AX support
Comfast CF-E393AX is a dual-band Wi-Fi 6 POE ceiling mount access point.
Oem firmware is a custom openwrt 21.02 snapshot version.
We can gain access via ssh once we remove the root password.
Hardware specification:
SoC: MediaTek MT7981A 2x A53
Flash: 128 MB SPI-NAND
RAM: 256MB DDR3
Ethernet: 1x 10/100/1000 Mbps built-in PHY (WAN)
1x 10/100/1000/2500 Mbps MaxLinear GPY211C (LAN)
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976D
LEDS: 1x (Red, Blue and Green)
Button: Reset
UART: 3.3v, 115200n8
--------------------------
| Layout |
| ----------------- |
| 4 | VCC GND TX RX | <= |
| ----------------- |
--------------------------
Gain SSH access:
1. Login into web interface (http://apipaddress/computer/login.html),
and download the
configuration(http://apipaddress/computer/config.html).
2. Rename downloaded backup config - 'backup.file to backup.tar.gz',
Enter 'fakeroot' command then decompress the configuration:
tar -zxf backup.tar.gz
3. Edit 'etc/shadow', update (remove) root password:
With password =
'root:$1$xf7D0Hfg$5gkjmvgQe4qJbe1fi/VLy1:19362:0:99999:7:::'
'root:$1$xf7D0Hfg$5gkjmvgQe4qJbe1fi/VLy1:19362:0:99999:7:::'
to
Without password =
'root::0:99999:7:::'
'root::0:99999:7:::'
4. Repack 'etc' directory back to a new backup file:
tar -zcf backup-ssh.tar.gz etc/
5. Rename new config tar.gz file to 'backup-ssh.file'
Exit fakeroot - 'exit'
6. Upload new configuration via web interface, now you
can SSH with the following:
'ssh -vv -o HostKeyAlgorithms=+ssh-rsa \
-o PubkeyAcceptedAlgorithms=+ssh-rsa root@192.168.10.1'.
Backup the mtd partitions
- https://openwrt.org/docs/guide-user/installation/generic.backup
7. Copy openwrt factory firmware to the tmp folder to install via ssh:
'scp -o HostKeyAlgorithms=+ssh-rsa \
-o PubkeyAcceptedAlgorithms=+ssh-rsa \
*-mediatek-filogic-comfast_cf-e393ax-squashfs-factory.bin \
root@192.168.10.1:/tmp/'
'sysupgrade -n -F \
/tmp/*--mediatek-filogic-comfast_cf-e393ax-squashfs-factory.bin'
8. Once led has stopped flashing - Connect via ssh with the
default openwrt ip address - 'ssh root@192.168.1.1'
9. SSH copy the openwrt sysupgrade firmware and upgrade
as per the default instructions.
Signed-off-by: David Bentham <db260179@gmail.com>
(cherry picked from commit
d8f4453bf2de9fd9baf3d660ed12e0797ff2cfdb)
Leon M. Busch-George [Fri, 13 Oct 2023 10:44:11 +0000 (12:44 +0200)]
mediatek: add support for YunCore AX835
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: 16MB NOR
RAM: 256MB
Ethernet: 2x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset
Power: DC 12V 1A, PoE 802.3af 48V
Flash instructions:
Option #1 - SSH
I was able to SSH into the stock firmware of my device.
1. Attach the router to the network
2. Use scp (-O) to copy the sysupgrade image
3. Connect using SSH and run `sysupgrade -n`
Option #2 - U-Boot
One way to use the bootloader for flashing is using TFTP:
1. Connect to the router using an ethernet cable
2 Spin up a TFTP server serving the sysupgrade file
3. Open the case and attach a UART
4. Attach power to the router and interrupt the countdown by pressing
any key
5. Select option #2 (Upgrade firmware)
6. Enter IP address information and image name
7. Wait patiently
Co-Authored-By: Enrique Rodríguez Valencia <enrique.rodriguez@galgus.net>
Co-Authored-By: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
(cherry picked from commit
b4086f44cd8a739458a0fd12cfaf684515507614)
Daniel Golle [Fri, 17 Nov 2023 02:25:09 +0000 (02:25 +0000)]
mediatek: add support for Adtran SmartRG Bonanza Peak series
The Bonanza Peak series are a couple of MT7986-powered 2.5 GBit/s
Wi-Fi 6 residential gateway, access point and mesh router products.
All of them come with an eMMC to boot from, are powered via USB-C and
got a USB 3.0 type-A port. All of them got a Dialog (Renesas)
DA14531
Bluetooth module connected via UART. If the device was previously
running stock firmware, the BT chip's internal flash has been loaded
with firmware and it can be attached using hciattach when using
OpenWrt.
SOC: MediaTek MT7986A
RAM: 2 GiB DDR4
eMMC: 8 GiB
Bluetooth: BLE5 (
DA14531)
Serial: 3.3V level, 115200 8n1 on 4-pin connector
* SDG-8612 - Dual-band RJ-45 gateway
2x 2.5G MaxLinear PHY for WAN port
3x 1GE LAN ports via MT7531 switch
* SDG-8614 - Dual-band SFP gateway
1x SFP cage with up to 2.5G speed
1x 2.5G MaxLinear PHY for LAN port
3x 1GE LAN ports via MT7531 switch
* SDG-8622 - Tri-band mesh router
2x 2.5G MaxLinear PHY
The MT7986 2G and 5G are used as 2G and 5G high band.
There’s a MT7915 PCIe card for 5G low band.
* SDG-8632 - Tri-band mesh router with 6 GHz
2x 2.5G MaxLinear PHY
The MT7986 serves the 2G and 6G bands.
There’s a MT7915 PCIe card for 5G.
Installation via U-Boot serial console:
0. setup TFTP server with IP 192.168.1.10/24, place initramfs image
renamed to openwrt.XXX where XXX is the internal product number:
SDG-8612: XXX = 412
SDG-8614: XXX = 414
SDG-8622: XXX = 422
SDG-8632: XXX = 432
1. connect to the serial console and power on the device.
Interrupt the bootloader by pressing 'st'
2. setenv boot_mode openwrt ; saveenv
3. run boot1
Load firmware via TFTP and write to flash
4. run boot2
Now OpenWrt initramfs should boot
5. upload sysupgrade.bin via scp to /tmp
6. sysupgrade
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit
3aa686f8d4d89ab28e749874c4b5e82d46685f3c)
Chukun Pan [Sun, 5 Nov 2023 15:02:09 +0000 (23:02 +0800)]
uboot-envtools: filogic: reorder alphabetically
Reorder scripts to keep alphabetical order.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
(cherry picked from commit
4825defe449883cb287bc46a93048473878003f0)
Rafał Miłecki [Sun, 17 Mar 2024 21:20:14 +0000 (22:20 +0100)]
kernel: backport some useful LED_FUNCTION_* defines for DT
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit
081cd769fc3e1de7709d7473b2560aaa549e2b05)
Shiji Yang [Tue, 31 Oct 2023 10:21:37 +0000 (18:21 +0800)]
generic: add more DT LED color and function definitions
Openwrt supports hundreds of devices. These newly added LED colors
and functions can help developers better describe LED indicators.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
(cherry picked from commit
6c41c585e37c44e25bc8d63c216635285aa05461)
Felix Fietkau [Thu, 16 May 2024 20:15:09 +0000 (22:15 +0200)]
mt76: update to Git HEAD (2024-04-03)
605624a4e17b mt76: fix path to page_pool helper include
e4de3592c4e3 wifi: mt76: mt7603: fix tx queue of loopback packets
446f652c967c wifi: mt76: mt7603: add wpdma tx eof flag for PSE client reset
669aba47a145 wifi: mt76: mt7915: fix HE PHY capability regression
5914ea57a31f wifi: mt76: mt7915: workaround dubious x | !y warning
e8b5991f7dac wifi: mt76: mt7915: workaround too long expansion sparse warnings
e507b4e32ead wifi: mt76: mt7921: fix fw used for offload check for mt7922
725f531c1459 wifi: mt76: connac: check for null before dereferencing
b108dda7e201 wifi: mt76: mt7996: fix size of txpower MCU command
5b7616491f07 wifi: mt76: mt7921: introduce mt7920 PCIe support
0436995feca9 wifi: mt76: mt7921s: fix potential hung tasks during chip recovery
75759dca73d5 wifi: mt76: mt7925: ensure 4-byte alignment for suspend & wow command
b96ab5e62010 wifi: mt76: mt7996: fix uninitialized variable in mt7996_irq_tasklet()
7ff11c7259a3 wifi: mt76: sdio: move mcu queue size check inside critical section
02846a5d0f0f wifi: mt76: mt7915: Remove unused of_gpio.h
cb8df32e0475 wifi: mt76: mt7996: disable rx header translation for BMC entry
a4c4b550512e wifi: mt76: connac: use peer address for station BMC entry
260c5b7c3ba0 wifi: mt76: mt7996: set RCPI value in rate control command
0b7e645db9c2 wifi: mt76: connac: enable HW CSO module for mt7996
f19035fe0b4d wifi: mt76: mt7996: fix non-main BSS no beacon issue for MBSS scenario
424e9df466ce wifi: mt76: mt7996: fix potential memory leakage when reading chip temperature
f70cb4f0508e wifi: mt76: connac: enable critical packet mode support for mt7992
5f1bf8865247 wifi: mt76: mt7996: add sanity checks for background radar trigger
1e336a8582dc wifi: mt76: connac: use muar idx 0xe for non-mt799x as well
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit
a10a6fbac794b30885d65ec817ebdcfe9f94d78a)
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Ian Oderon [Sat, 9 Dec 2023 04:48:35 +0000 (12:48 +0800)]
mediatek: add support for Zbtlink ZBT-Z8103AX
Specifications:
SoC: MediaTek MT7981B
RAM: 256MiB
Flash: SPI-NAND 128 MiB
Switch: 1 WAN, 3 LAN (Gigabit)
Buttons: Reset, Mesh
Power: DC 12V 1A
WiFi: MT7976CN
UART: 115200n8
UART Layout:
VCC-RX-TX-GND
No. of Antennas: 6
Note: Upon opening the router, only 5 antennas were connected
to the mainboard.
Led Layout:
Power-Mesh-5gwifi-WAN-LAN3-LAN2-LAN1-2gWiFi
Buttons:
Reset-Mesh
Installation:
A. Through OpenWrt Dashboard:
If your router comes with OpenWrt preinstalled (modified by the seller),
you can easily upgrade by going to the dashboard (192.168.1.1) and then
navigate to System -> Backup/Flash firmware, then flash the firmware
B. Through TFTP
Standard installation via UART:
1. Connect USB Serial Adapter to the UART, (NOTE: Don't connect the VCC pin).
2. Power on the router. Make sure that you can access your router via UART.
3. Restart the router then repeatedly press ctrl + c to skip default boot.
4. Type > bootmenu
5. Press '2' to select upgrade firmware
6. Press 'Y' on 'Run image after upgrading?'
7. Press '0' and hit 'enter' to select TFTP client (default)
8. Fill the U-Boot's IP address and TFTP server's IP address.
9. Finally, enter the 'firmware' filename.
Signed-off-by: Ian Oderon <ianoderon@gmail.com>
(cherry picked from commit
4300bc668819a77226b6e8ea079d3067f216e7bb)
Rodrigo Balerdi [Sat, 6 Apr 2024 06:18:00 +0000 (03:18 -0300)]
base-files: minor fix to mmc_get_mac_ascii function
This is mostly a cosmetic cleanup. The absence of
the return statement was not causing any problems.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
(cherry picked from commit
8cf4ac5195476356a14678ae72897e563881b15e)
Daniel Golle [Fri, 17 Nov 2023 00:02:05 +0000 (00:02 +0000)]
base-files: add mmc_get_mac_ascii function
Similar to the *_get_mac_binary function, also split the common parts
off mtd_get_mac_ascii into new get_mac_ascii function and introduce
mmc_get_mac_ascii which uses it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit
45c85c1827d45f8041b8f270d80bf6fff328069c)
Daniel Golle [Wed, 29 Nov 2023 21:10:37 +0000 (21:10 +0000)]
mediatek: add kmod-usb3 to default package set of the ZBT-Z8102AX
Include XHCI USB drivers on the ZBT-Z8102AX router, the drivers are
required to be able to use the USB-connected M.2 slots for 4G/5G modems.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit
507ad4f078d202304414a795d580abdee64f2b84)
projects / openwrt / openwrt.git / log