Luka Perkov [Wed, 13 Apr 2016 07:33:24 +0000 (07:33 +0000)]
rpcd: update to latest version
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 49162
John Crispin [Sat, 9 Apr 2016 14:47:35 +0000 (14:47 +0000)]
ramips: remove accidentally comitted code
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 49161
Rafał Miłecki [Sat, 9 Apr 2016 13:23:25 +0000 (13:23 +0000)]
bcm53xx: add switch config workaround for R8500 and DIR-885L
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 49160
Rafał Miłecki [Sat, 9 Apr 2016 13:20:19 +0000 (13:20 +0000)]
bcm53xx: fix regression in generating network config
Syntax error was added in r49122.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 49159
John Crispin [Sat, 9 Apr 2016 10:26:46 +0000 (10:26 +0000)]
ar71xx: add TP-Link TL-WA901ND-v4 support
Signed-off-by: Tiziano Bacocco <tizbac2@gmail.com>
SVN-Revision: 49158
John Crispin [Sat, 9 Apr 2016 10:26:41 +0000 (10:26 +0000)]
ar71xx: add support for Compex WPJ342
OpenWrt can be flashed with following uboot commands:
tftpboot 0x80500000 openwrt-ar71xx-generic-wpj342-16M-squashfs-sysupgrade.bin
erase 0x9f030000 +$filesize
cp.b $fileaddr 0x9f030000 $filesize
Signed-off-by: Christian Mehlis <christian@m3hlis.de>
SVN-Revision: 49157
John Crispin [Sat, 9 Apr 2016 10:26:37 +0000 (10:26 +0000)]
ar71xx: fix nondeterministic hangs during bootconsole/console handover
Reconfiguring the UART when the FIFO is not empty may cause the boot to
hang. This hang is extremely suspectible to timing differences; recompiling
the kernel with the same configuration, but different UTS_VERSION
timestamps can yield images that hang more or less often. Sometimes images
are produced that hang reproducibly.
This patch should also make it into one of the next linux-stable releases,
but it's better to get this fixed as soon as possible.
Fixes #21773, #21857.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 49156
John Crispin [Sat, 9 Apr 2016 10:26:34 +0000 (10:26 +0000)]
ar71xx: add OM5P-ACv2 to the OM5P-AC profile
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49155
John Crispin [Sat, 9 Apr 2016 10:26:31 +0000 (10:26 +0000)]
ar71xx: extract ath10k wifi board.bin for the OpenMesh OM5P-ACv2 board
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49154
John Crispin [Sat, 9 Apr 2016 10:26:28 +0000 (10:26 +0000)]
uboot-envtools: add OpenMesh OM5P-ACv2 support
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49153
John Crispin [Sat, 9 Apr 2016 10:26:25 +0000 (10:26 +0000)]
om-watchdog: add OpenMesh OM5P-ACv2 support
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49152
John Crispin [Sat, 9 Apr 2016 10:26:22 +0000 (10:26 +0000)]
ar71xx: enable sysupgrade for the OpenMesh OM5P-ACv2
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49151
John Crispin [Sat, 9 Apr 2016 10:26:18 +0000 (10:26 +0000)]
ar71xx: add user-space support for the OpenMesh OM5P-ACv2
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49150
John Crispin [Sat, 9 Apr 2016 10:26:15 +0000 (10:26 +0000)]
ar71xx: add kernel support for the OpenMesh OM5P-ACv2 board
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49149
John Crispin [Sat, 9 Apr 2016 10:26:11 +0000 (10:26 +0000)]
ar71xx: create profile and build image for the OpenMesh OM5P-AC board
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49148
John Crispin [Sat, 9 Apr 2016 10:26:08 +0000 (10:26 +0000)]
ar71xx: extract ath10k wifi board.bin for the OpenMesh OM5P-AC board
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49147
John Crispin [Sat, 9 Apr 2016 10:26:04 +0000 (10:26 +0000)]
uboot-envtools: add OpenMesh OM5P-AC support
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49146
John Crispin [Sat, 9 Apr 2016 10:26:01 +0000 (10:26 +0000)]
om-watchdog: add OpenMesh OM5P-AC support
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49145
John Crispin [Sat, 9 Apr 2016 10:25:57 +0000 (10:25 +0000)]
ar71xx: enable sysupgrade for the OpenMesh OM5P-AC
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49144
John Crispin [Sat, 9 Apr 2016 10:25:54 +0000 (10:25 +0000)]
scripts/om-fwupgradecfg-gen.sh: add support for the OM5P-AC
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49143
John Crispin [Sat, 9 Apr 2016 10:25:51 +0000 (10:25 +0000)]
ar71xx: add user-space support for the OpenMesh OM5P-AC
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49142
John Crispin [Sat, 9 Apr 2016 10:25:47 +0000 (10:25 +0000)]
ar71xx: add kernel support for the OpenMesh OM5P-AC board
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49141
John Crispin [Sat, 9 Apr 2016 10:25:42 +0000 (10:25 +0000)]
scripts/om-fwupgradecfg-gen.sh: Generate sha256sum for uboot verification
Future Open Mesh u-boot versions are changing the check of the image files
(vmlinux, rootfs) from md5 to sha256. Having both in them should be enough
to ensure backward and forward compatibility.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49140
John Crispin [Sat, 9 Apr 2016 10:25:38 +0000 (10:25 +0000)]
brcmfmac43430-firmware: switch to @GITHUB download alias
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 49139
John Crispin [Sat, 9 Apr 2016 10:25:34 +0000 (10:25 +0000)]
download: add @GITHUB download facility
Define a new alias (@GITHUB) for downloading raw github repository files
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 49138
John Crispin [Sat, 9 Apr 2016 10:25:29 +0000 (10:25 +0000)]
lantiq-dsl: add missing blank in dsl output
blank inserted before ACTATP
Signed-off-by: Florian Eckert <Eckert.Florian@googlemail.com>
SVN-Revision: 49137
John Crispin [Sat, 9 Apr 2016 10:25:24 +0000 (10:25 +0000)]
lantiq-dsl: bugfix latency values swapped for lucistat
swapped wrong latency output
Signed-off-by: Florian Eckert <Eckert.Florian@googlemail.com>
SVN-Revision: 49136
John Crispin [Sat, 9 Apr 2016 10:25:20 +0000 (10:25 +0000)]
lantiq-dsl: bugfix db negative sign after comma
If db is negative minus sign was shown after comma
Signed-off-by: Florian Eckert <Eckert.Florian@googlemail.com>
SVN-Revision: 49135
John Crispin [Sat, 9 Apr 2016 10:25:16 +0000 (10:25 +0000)]
arc770: enable unaligned access handling simulation in software
This enables misaligned access handling by software in Linux kernel.
With some wireless drivers (ath9k-htc and mt7601u for example) we see
misaligned accesses here and there and to cope with that without
fixing stuff in the drivers we're just gracefully handling it on ARC.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
SVN-Revision: 49134
John Crispin [Sat, 9 Apr 2016 10:25:13 +0000 (10:25 +0000)]
arc770: build kmod-ath9k-htc wpad-mini by default
AXS101 beind a development board lacks built-in wireles inerfaces.
So we have to use external USB dongles to turn the board into
wireless router.
The best USB Wi-Fi dongles to work in AP-mode seem to be based on
ath9k-htc chipset.
And so with that change we add support of mentioned dongles in
default and axs101 builds.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
SVN-Revision: 49133
John Crispin [Sat, 9 Apr 2016 10:25:08 +0000 (10:25 +0000)]
mediatek: update patches
adds a few ethernet fixes
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 49132
John Crispin [Sat, 9 Apr 2016 10:25:03 +0000 (10:25 +0000)]
ramips: Disable the SD driver by default on MT7621
The SD driver has been a long and dragging issue on the MT7621 platforms as it hasn't worked for
months resulting in unbootable devices. Until it's fixed, disable it in the default profiles.
Reports / Discussed here:
https://dev.openwrt.org/ticket/21392
https://dev.openwrt.org/ticket/21834
https://dev.openwrt.org/ticket/21995
https://forum.openwrt.org/viewtopic.php?id=59092
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
SVN-Revision: 49131
John Crispin [Sat, 9 Apr 2016 10:24:58 +0000 (10:24 +0000)]
ramips: Fixes for LinkIt 7688
Misc fixes for LinkIt 7688 board:
- Copy the right wireless firmware for the mt7688
- Add back '0065-mt7688-fixes.patch', left out after the move to Linux 4.4.
- Remove SPI_DEV from linux config which otherwise causes a massive warning
- Add wmac to LINKIT7688.dts so wireless works
Signed-off-by: Adam Kent <adam@semicircular.net>
SVN-Revision: 49130
John Crispin [Sat, 9 Apr 2016 10:24:55 +0000 (10:24 +0000)]
ramips: Adjust image size limit for the D-Link DIR-860L B1
Currently the maximum image size defaults to 8Mbyte even though this model has 16Mbyte of flash memory.
Tested and works on my device.
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
SVN-Revision: 49129
John Crispin [Sat, 9 Apr 2016 10:24:52 +0000 (10:24 +0000)]
ramips: fix for Planex MZK-WDPR (lcd control gpio).
add lcd control gpio pin for Planex MZK-WDPR.
LCD board initial timming is GPIO control.
Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
SVN-Revision: 49128
John Crispin [Sat, 9 Apr 2016 10:24:47 +0000 (10:24 +0000)]
ramips: mt7621: fix Ubiquiti EdgeRouter X profile
Remove unnecessary packages to reduce image size so it fits in initramfs (to enable upgrading from factory firmware).
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 49127
John Crispin [Sat, 9 Apr 2016 10:24:44 +0000 (10:24 +0000)]
ramips: mt7621: sync MQmaker WiTi profile name to dts name
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 49126
John Crispin [Sat, 9 Apr 2016 10:24:40 +0000 (10:24 +0000)]
ramips: enable device profiling by dts
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 49125
John Crispin [Sat, 9 Apr 2016 10:24:36 +0000 (10:24 +0000)]
ramips: mt7621: add a device to TARGET_DEVICES after it's definition
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 49124
John Crispin [Sat, 9 Apr 2016 10:24:29 +0000 (10:24 +0000)]
ramips: mt7621: fix initramfs image for ubnt-erx
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 49123
Rafał Miłecki [Sat, 9 Apr 2016 09:59:21 +0000 (09:59 +0000)]
bcm53xx: add basic support for Netgear R7900
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 49122
Rafał Miłecki [Fri, 8 Apr 2016 20:37:14 +0000 (20:37 +0000)]
bcm53xx: add PCI iproc patch adding abort handler
This prevents die() during PCI bus probe.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 49121
Rafał Miłecki [Fri, 8 Apr 2016 20:36:57 +0000 (20:36 +0000)]
Revert "bcm53xx: revert patch removing imprecise abort workaround"
This reverts commit r48961. It didn't fix PCIe host driver issue as
there are more aborts triggered by it.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 49120
Imre Kaloz [Wed, 6 Apr 2016 08:30:28 +0000 (08:30 +0000)]
mwlwifi: upgrade to 10.3.0.17-
20160324
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 49119
Rafał Miłecki [Fri, 1 Apr 2016 16:49:50 +0000 (16:49 +0000)]
bcm53xx: use the final fix for iproc bcma regression
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 49114
Rafał Miłecki [Fri, 1 Apr 2016 16:49:34 +0000 (16:49 +0000)]
bcm53xx: drop unneeded 4.3 SPROM patch
4.3 isn't oficially used anymore but it may be useful for debugging PCI
host driver regression. SPROM driver doesn't seem to work correctly with
4.3:
[ 2.336686] bcma: bus0: Using fallback SPROM failed (err -2)
[ 2.342366] bcma: bus0: No SPROM available
but it at least compiles now.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 49113
John Crispin [Fri, 1 Apr 2016 07:12:17 +0000 (07:12 +0000)]
package/utils/usbutils: Update USB IDs list to snapshot 2015-12-17
Updates USB IDs list to snapshot 2015-12-17 and changes copyright to
2016.
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
SVN-Revision: 49112
John Crispin [Fri, 1 Apr 2016 07:12:14 +0000 (07:12 +0000)]
package/libs/libusb: Update to 1.0.20
Updates libusb to version 1.0.20 and changes copyright to 2016.
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
SVN-Revision: 49111
John Crispin [Fri, 1 Apr 2016 07:12:11 +0000 (07:12 +0000)]
package/libs/lzo: update version to 2.09
Updates lzo to version 2.09 and changes copyright to 2016.
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
SVN-Revision: 49110
John Crispin [Fri, 1 Apr 2016 07:12:07 +0000 (07:12 +0000)]
ar71xx: WPN824N: enable buttons
Enable buttons connected to the GPIOs of the AR9285.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
SVN-Revision: 49109
John Crispin [Fri, 1 Apr 2016 07:12:03 +0000 (07:12 +0000)]
ar71xx: WPN824N: set WLAN LED name
Make use of ap9x_pci_setup_wmac_led_name() to set the name of the WLAN
LED.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
SVN-Revision: 49108
John Crispin [Fri, 1 Apr 2016 07:12:00 +0000 (07:12 +0000)]
ar71xx: fix the revision of a few TP-LINK devices in AR71XX_MODEL to match labels/image names
Let's not confuse users about the revisions of their devices when we can
easily avoid it.
Not tested on real hardware.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 49107
John Crispin [Fri, 1 Apr 2016 07:11:56 +0000 (07:11 +0000)]
ar71xx: avoid AR71XX_MODEL ending with a space on some TP-LINK-like devices
Instead of adding the space when combining $model and $hwver, add the space
to the beginning of $hwver, so the resulting string won't end with a space
when $hwver is set to the empty string.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 49106
John Crispin [Fri, 1 Apr 2016 07:11:53 +0000 (07:11 +0000)]
ar71xx: check both HWID and HWREV on upgrades of TP-LINK devices
There's no reason for us to be more lenient than the stock firmware, so
better check the HWREV as well to avoid bricked devices.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 49105
John Crispin [Fri, 1 Apr 2016 07:11:48 +0000 (07:11 +0000)]
ramips: move different subtarget image generation to separate makefiles to improve maintainability
- all subtarget specific defines are in their own files
- common defines left in main Makefile
- each subtarget makefile idefed with SUBTARGET
- all subtargets compile tested
- few seems to be broken/unneeded things marked with FIXME
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 49104
John Crispin [Fri, 1 Apr 2016 07:11:43 +0000 (07:11 +0000)]
brcm2708: add brcmfmac43430-firmware-sdio for Rasberry Pi 3
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 49103
John Crispin [Fri, 1 Apr 2016 07:11:39 +0000 (07:11 +0000)]
brcmfmac43430-firmware: add new package
This adds the firmware needed for the BCM43438 included in Raspberry Pi 3.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 49102
John Crispin [Fri, 1 Apr 2016 07:11:34 +0000 (07:11 +0000)]
ar71xx: WNR2200: enable control of all LEDs and buttons
This patch provides full GPIO support for WNR2200 (LEDs and buttons).
It exposes all LEDs to operating system, including Ethernet ones.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 49101
John Crispin [Fri, 1 Apr 2016 07:11:27 +0000 (07:11 +0000)]
ar71xx: WNR2200: fix for random WLAN MAC
Fix for invalid/random/duplicate WLAN MAC address in WNR2200.
Permanent platform MAC is calculated and assigned during system startup.
WLAN MAC follows wired Ethernet interface addresses.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 49100
John Crispin [Fri, 1 Apr 2016 07:11:23 +0000 (07:11 +0000)]
ar71xx: Add TL-WR841N/ND v11 support
This patch adds support for the TP-Link TL-WR841N/ND to trunk. It is
similar to the already supported v10 - see [1]. I have added support
based on that topic; in the meantime it has been confirmed working
(see the forum thread, and also [2]).
Signed-off by Stijn Segers <francesco.borromini@inventati.org>
[1]: https://forum.openwrt.org/viewtopic.php?id=61309
[2]: https://forum.openwrt.org/viewtopic.php?id=63657
SVN-Revision: 49099
John Crispin [Fri, 1 Apr 2016 07:11:18 +0000 (07:11 +0000)]
mediatek: update patches
add fixes for
* ethernet
* cpufreq
* nand
* a7-timer
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 49098
Rafał Miłecki [Wed, 30 Mar 2016 16:41:26 +0000 (16:41 +0000)]
kernel: update kernel 3.18 to version 3.18.29
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 49096
Rafał Miłecki [Wed, 30 Mar 2016 12:26:24 +0000 (12:26 +0000)]
bcm53xx: improve USB 2.0 PHY support for BCM4709 and BCM47094
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 49094
Rafał Miłecki [Wed, 30 Mar 2016 10:23:02 +0000 (10:23 +0000)]
bcm53xx: support USB 3.0 PHY on BCM4707 rev. 6 and BCM47094
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 49091
Rafał Miłecki [Wed, 30 Mar 2016 10:22:57 +0000 (10:22 +0000)]
bcm53xx: simpify USB 3.0 PHY initialization
We can use one code path for BCM4707 rev. 4 and BCM53018.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 49090
Zoltan Herpai [Tue, 29 Mar 2016 11:42:14 +0000 (11:42 +0000)]
package: uboot-sunxi: various changes
- bump to 2016.03
- add bugfixes related to 2016.03 update
- sync DTS files with mainline
- add support for non-standard uEnv.txt
- add initial support for Theobroma A31-yQ7 devboard
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
SVN-Revision: 49089
Luka Perkov [Fri, 25 Mar 2016 12:07:03 +0000 (12:07 +0000)]
uboot-mvebu: add package
Signed-off-by: Andrej Vlasic <andrej.vlasic@sartura.hr>
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
SVN-Revision: 49088
Luka Perkov [Thu, 24 Mar 2016 21:09:34 +0000 (21:09 +0000)]
ar71xx: cosmetic fix of alfa ap120c/ap96 ordering
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 49086
Luka Perkov [Wed, 23 Mar 2016 22:31:41 +0000 (22:31 +0000)]
uboot-envtools: add support for ap120c
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 49083
Luka Perkov [Wed, 23 Mar 2016 22:31:38 +0000 (22:31 +0000)]
ar71xx: add support for ap120c
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 49082
John Crispin [Wed, 23 Mar 2016 12:52:50 +0000 (12:52 +0000)]
ar71xx: migrate tplink cpe510 to new build steps
cpe510: Tested sysupgrade and initramfs.
Untested: webIf w/ factory.bin & recovery.bin
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 49081
John Crispin [Wed, 23 Mar 2016 12:52:47 +0000 (12:52 +0000)]
ar71xx/image: allow builds of loader without cmdline injecting
On most platforms the cmdline is supplied by the loader to the kernel.
When using an elf loader with cmdline the size is bloated by 512k.
For loader-elf platforms like the cpe510 better use loader-elf but patch
the cmdline into the kernel.
wdr1043: Tested loader still works using sysupgade image.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 49080
John Crispin [Wed, 23 Mar 2016 12:52:44 +0000 (12:52 +0000)]
ar71xx/image: introduce LOADER_TYPE to support elf loaders
The loader decompress a lzma compressed kernel. Some bootloaders
only support elf files like the tplink cpe510
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 49079
John Crispin [Wed, 23 Mar 2016 12:52:41 +0000 (12:52 +0000)]
uboot-zynq: Update to U-Boot 2016.03 release
Signed-off-by: Jason Wu <jason.wu.misc@gmail.com>
SVN-Revision: 49078
John Crispin [Wed, 23 Mar 2016 12:52:38 +0000 (12:52 +0000)]
zynq: Simplify boot-img build
by adding Device/DefaultConfig macro to define the dts and device in
lower case.
Signed-off-by: Jason Wu <jason.wu.misc@gmail.com>
SVN-Revision: 49077
John Crispin [Wed, 23 Mar 2016 12:52:35 +0000 (12:52 +0000)]
ar71xx: WNR1000v2: enable control of all LEDs and buttons
This patch provides full GPIO support for WNR1000v2 (LEDs and buttons).
It exposes all LEDs to operating system, including Ethernet ones.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 49076
John Crispin [Wed, 23 Mar 2016 12:52:31 +0000 (12:52 +0000)]
ar71xx: Add QCA955X GPIO mux and function definitions
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49075
John Crispin [Wed, 23 Mar 2016 12:52:27 +0000 (12:52 +0000)]
ar71xx: Add support for ath79_gpio_function_* on QCA955X
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49074
John Crispin [Wed, 23 Mar 2016 12:52:24 +0000 (12:52 +0000)]
mac80211: build airo on x86 only
airo requires ISA_DMA_API and
that symbol is only set on some ppc,malta,x86
x86 is probably only platform where that driver is used
fixes buildbot errors on ar71xx,lantiq ...:
airo.ko is missing
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 49073
John Crispin [Wed, 23 Mar 2016 12:52:20 +0000 (12:52 +0000)]
Revert "ar71xx: Clear bits in ath79_setup_qca955x_eth_cfg"
Not all mach-* files set all boards correctly in ETH_CFG. They depend on
some preset values by u-boot which were not previously modified by
ath79_setup_qca955x_eth_cfg. Avoiding to modify them in this function keeps
it backward compatible for these boards.
This reverts commit
119b8ab2c2eac237ec4e9c4d0ed53df22b5c6978.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49072
John Crispin [Wed, 23 Mar 2016 12:52:17 +0000 (12:52 +0000)]
Revert "ar71xx: Allow to set the RXDV, RXD, TXD, TXE delays for QCA955x"
The default delays RXD 3. RDV 3, TXD 0, TXE 0 doesn't seem to work for some
boards. These boards depend on the preset values of u-boot which may
differ.
This reverts commit
f2d4bb96b62512caa161dcc2867c91692fb16a38.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49071
John Crispin [Wed, 23 Mar 2016 12:52:12 +0000 (12:52 +0000)]
ar71xx: Use private version of ath79_setup_qca955x_eth_cfg for MR1750
The MR1750 must unset some bits in ETH_CFG which were set by u-boot to work
correctly under OpenWrt. But the global function
ath79_setup_qca955x_eth_cfg will not unset all of them to increase the
backward compatiblity with older mach-* files. A private (simplified)
version for MR1750 can be used instead.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49070
John Crispin [Wed, 23 Mar 2016 12:52:09 +0000 (12:52 +0000)]
ar71xx: Use private version of ath79_setup_qca955x_eth_cfg for MR900
The MR900 must unset some bits in ETH_CFG which were set by u-boot to work
correctly under OpenWrt. But the global function
ath79_setup_qca955x_eth_cfg will not unset all of them to increase the
backward compatiblity with older mach-* files. A private (simplified)
version for MR900 can be used instead.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49069
John Crispin [Wed, 23 Mar 2016 12:52:05 +0000 (12:52 +0000)]
oxnas: set ubifs parameters for Default profile
Work-around obsolete mkfs/ubifs code.
Unlike squashfs, ubifs images should be generated per-device so
minimum I/O unit size, logical erase block size, maximum logical erase
block count can be defined for the specific flash-chips parameters.
Also, generating ubinized images is unrelated to rootfs being ubifs or
squashfs, but rather depends on the device supporting UBI or not.
In the meantime and in order to fix an error which currently causes the
image generation on buildbot to fail, work-around by defining
UBIFS_OPTS for the Default profile.
See also
http://buildbot.openwrt.org:8010/builders/oxnas/builds/246/steps/compile_8/logs/stdio
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 49068
John Crispin [Wed, 23 Mar 2016 11:12:34 +0000 (11:12 +0000)]
mediatek: patch block2mtd to allow cmdlineparts to work
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 49067
John Crispin [Tue, 22 Mar 2016 21:14:51 +0000 (21:14 +0000)]
mediatek: update patches
fixes trgmii on old eco and adds nand support
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 49066
John Crispin [Mon, 21 Mar 2016 20:42:56 +0000 (20:42 +0000)]
mt76: fix compile error
gcc complained about uninitialized variables
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 49065
John Crispin [Mon, 21 Mar 2016 20:42:51 +0000 (20:42 +0000)]
mediatek: bump to v4.4
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 49064
Gabor Juhos [Mon, 21 Mar 2016 14:18:53 +0000 (14:18 +0000)]
generic/4.4: remove ISSI SI25CD512 SPI flash support patch
The flash is already supported in mainline kernel since 4.3-rc1.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 49063
Gabor Juhos [Mon, 21 Mar 2016 13:15:29 +0000 (13:15 +0000)]
ramips: lzma-loader: fix O32 ABI conformance
According to the calling convention of the o32 ABI the
caller function must reserve stack space for $a0-$a3
registers in case the callee needs to save its arguments.
The assembly startup code does not reserve stack space
for these registers thus when the main C function needs
to save its arguments, that will cause a stack overflow.
Fix the assembly code to reserve stack space for the
registers to avoid that.
Untested. It seems that the lzma-loader is not used at all?
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 49062
Gabor Juhos [Mon, 21 Mar 2016 13:15:25 +0000 (13:15 +0000)]
lantiq: lzma-loader: fix O32 ABI conformance
According to the calling convention of the o32 ABI the
caller function must reserve stack space for $a0-$a3
registers in case the callee needs to save its arguments.
The assembly startup code does not reserve stack space
for these registers thus when the main C function needs
to save its arguments, that will cause a stack overflow.
Fix the assembly code to reserve stack space for the
registers to avoid that.
Compile tested only.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 49061
Gabor Juhos [Mon, 21 Mar 2016 13:15:22 +0000 (13:15 +0000)]
brcm47xx: lzma-loader: fix cache invalidation
The current code only partially invalidates both caches
because the cache size and cache-line size values are
incorrectly passed to the C code.
Fix the assembly code to pass the arguments in the correct
order.
Compile tested only.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 49060
Gabor Juhos [Mon, 21 Mar 2016 13:15:21 +0000 (13:15 +0000)]
brcm47xx: lzma-loader: remove trailing whitespaces from head.S
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 49059
Gabor Juhos [Mon, 21 Mar 2016 13:15:16 +0000 (13:15 +0000)]
adm5120: lzma-loader: fix cache invalidation
The current code only partially invalidates both caches
because the cache size and cache-line size values are
incorrectly passed to the C code.
Fix the assembly code to pass the arguments in the correct
order.
Compile tested only.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 49058
Gabor Juhos [Mon, 21 Mar 2016 13:15:13 +0000 (13:15 +0000)]
adm5120: lzma-loader: remove trailing whitespaces from head.S
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 49057
Gabor Juhos [Mon, 21 Mar 2016 13:15:09 +0000 (13:15 +0000)]
generic: lzma-loader: fix cache invalidation
The current code only partially invalidates both caches
because the cache size and cache-line size values are
incorrectly passed to the C code.
Fix the assembly code to pass the arguments in the correct
order.
Tested on RB532.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 49056
Gabor Juhos [Mon, 21 Mar 2016 13:15:05 +0000 (13:15 +0000)]
generic: lzma-loader: remove trailing whitespaces from start.S
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 49055
John Crispin [Sun, 20 Mar 2016 18:48:59 +0000 (18:48 +0000)]
odhcp6c : Silence mtu write error warnings
Silence warning "daemon.notice netifd: wan6 (1139): sh: write error: Invalid argument"
when an invalid MTU is received via RA as kernel refuses to accept IPv6 mtu values
which are smaller than 1280 and bigger than the device mtu.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
SVN-Revision: 49054
John Crispin [Sun, 20 Mar 2016 14:41:58 +0000 (14:41 +0000)]
ar71xx: WNR1000v2: fix for random WLAN MAC
Fix for invalid/random WLAN MAC address in WNR1000v2. Permanent platform
MAC is calculated and assigned during system startup. WLAN MAC follows
wired Ethernet interface addresses. This is the same fix as for WNR2000v3
and WNR612v2.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 49051
John Crispin [Sun, 20 Mar 2016 14:41:54 +0000 (14:41 +0000)]
lantiq: use upstream mechanism to append device tree file
Instead of using our patch-dtb program just place the device tree
behind the kernel binary and then let the in kernel mechanism fetch it.
This also adds support for having the device tree file in the boot
loader.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 49050
projects / openwrt / svn-archive / archive.git / log