Hauke Mehrtens [Sun, 30 Oct 2022 23:43:40 +0000 (00:43 +0100)]
Revert "at91:"
This reverts commit
7cc6ffa1b903524fe478804fd215bb858ae8c9b7.
This should have been folded in an other commit.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sun, 30 Oct 2022 22:37:53 +0000 (23:37 +0100)]
at91:
[CONFIG_PINCTRL_MCP23S08 is already unset in generic config]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Volodymyr Puiul [Wed, 19 Oct 2022 20:05:16 +0000 (00:05 +0400)]
ramips: add support for YunCore FAP640
It is an in-wall 802.11ax (Wi-Fi 6) router, based on MediaTek MT7621A.
Specifications:
- SoC: MT7621AT (880MHz, 2 Cores)
- RAM: 128 MB
- Flash: 16 MB SPI
- Wi-Fi:
- MT7915DN + MT7905DAN: 2.4/5 GHz
- Ethernet: 5x1GiE via MT7530, 1xWAN with POE and 4xLAN
- UART: J4 (115200 baud)
- Pinout: [3V3] (TXD) (RXD) (GND)
- Power: 802.11af/at PoE;
- Bootloader: U-Boot
- Buttons:
- Reset
- LEDs:
- Status - RGB controlled by
- GPIO 14 LOW - green color
- GPIO 15 LOW- red color
- GPIO 16 LOW - blue color
- WAN - gren color, controlled by switch GPIO 12 LOW
- LAN1 - gren color, controlled by switch GPIO 9 HIGH
- LAN2 - gren color, controlled by switch GPIO 6 LOW
- LAN3 - gren color, controlled by switch GPIO 3 LOW
- LAN4 - gren color, controlled by switch GPIO 0 LOW
Installation:
OEM firmware is based on LEDE with custom UI and support standard sysupgrade
variant of firmware. However it requires "*.ubin" extension for sysupgrade file.
Always select "Factory reset" switch on upgrade to OpenWRT, otherwise
router will not boot.
MAC addresses with OEM firmware:
vendor source
lan factory 0x4 (label)
5g factory 0x4 (label)
2g label with flipped bits bit in 1-st byte and bits 5, 6, 7 in
4-th byte
Example
label: 44:xx:xx:b7:xx:xx
lan: 44:xx:xx:b7:xx:xx
2g 46:xx:xx:c7:xx:xx
5g 44:xx:xx:b7:xx:xx
Signed-off-by: Volodymyr Puiul <volodymyr.puiul@gmail.com>
Csaba Sipos [Mon, 3 Oct 2022 17:13:22 +0000 (19:13 +0200)]
ipq40xx: add support for MikroTik hAP ac3 LTE6 kit
This adds support for the MikroTik RouterBOARD RBD53GR-5HacD2HnD
(hAP ac³ LTE6 kit), an indoor dual band, dual-radio 802.11ac
wireless AP with built-in Mini PCI-E LTE modem, one USB port, five
10/100/1000 Mbps Ethernet ports.
See https://mikrotik.com/product/hap_ac3_lte6_kit for more info.
Specifications:
- SoC: Qualcomm Atheros IPQ4019
- RAM: 256 MB
- Storage: 16 MB NOR
- Wireless:
· Built-in IPQ4019 (SoC) 802.11b/g/n 2x2:2, 3 dBi internal antennae
· Built-in IPQ4019 (SoC) 802.11a/n/ac 2x2:2, 5.5 dBi internal antennae
- Ethernet: Built-in IPQ4019 (SoC, QCA8075) , 5x 1000/100/10 port
- 1x USB Type A port
- 1x Mini PCI-E port (supporting USB)
- 1x Mini PCI-E LTE modem (MikroTik R11e-LTE6, Cat.6)
Installation:
Make sure your unit is runnning RouterOS v6 and RouterBOOT v6 (tested on 6.49.6).
0. Export your MikroTik license key (in case you want to use the device with RouterOS later)
1. Boot the initramfs image via TFTP
2. Upload the "openwrt-ipq40xx-mikrotik-mikrotik_hap-ac3-lte6-kit-squashfs-sysupgrade.bin" via SCP to the /tmp folder
3. Use sysupgrade to flash the image: sysupgrade -n /tmp/openwrt-ipq40xx-mikrotik-mikrotik_hap-ac3-lte6-kit-squashfs-sysupgrade.bin
4. Recovery to factory software is possible via Netinstall:
https://help.mikrotik.com/docs/display/ROS/Netinstall
Signed-off-by: Csaba Sipos <metro4@freemail.hu>
Florian Eckert [Wed, 26 Jan 2022 15:12:12 +0000 (16:12 +0100)]
target/mxs: replace gpio-mcp23s08 with pinctrl-mcp23s08
The dependency on the kernel module gpio-mcp23s08 is replaced by
pinctrl-mcp23s08-spi and pinctrl-mcp23s08-i2c, as the gpio-mpc23s08 kernel
module no longer exists.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Florian Eckert [Wed, 26 Jan 2022 15:11:09 +0000 (16:11 +0100)]
kernel: remove CONFIG_GPIO_MCP23S08 from default kernel configs
The kernel config option 'CONFIG_GPIO_MCP23S08' no longer exists.
Therefore, it is removed from the generic kernel configuration for
linux-5.10 and linux-5.15.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Florian Eckert [Wed, 26 Jan 2022 15:04:54 +0000 (16:04 +0100)]
target/at91: replace gpio-mcp23s08 with pinctrl-mcp23s08-spi update config
Adapt the device package to no longer use the gpio-mcp23s08 but instead
use the pinctrl-mcp23s08-spi. In addition, the kernel configuration was
adapted so that this can be built as a module and does not have to be
integrated directly into the kernel for this target.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Florian Eckert [Wed, 26 Jan 2022 14:29:18 +0000 (15:29 +0100)]
kernel: replace gpio-mcp23s08 with pinctrl-mcp23s08*
The kernel module gpio-mcp23s08 has been replaced by the new
pinctrl-mcp23s08* kernel modules.
There are now 3 kernel modules for this device
- Common module for both I2C and SPI kmod-pinctrl-mcp23s08
- Module for I2C kmod-pinctrl-mcp23s08-i2c
- Module for SPI kmod-pinctrl-mcp23s08-spi
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Roland Barenbrug [Mon, 8 Aug 2022 21:44:10 +0000 (23:44 +0200)]
ltq-vdsl-vr9-app: extend ubus call to provide DSL statistics
Adding a new method to `ubus call dsl` to retrieve DSL statistics
used to feed the DSL charts (bit allocation, SNR, QLN and HLOG)
Signed-off-by: Roland Barenbrug <roland@treslong.com>
[fix pointer error, clean up]
Signed-off-by: Andre Heider <a.heider@gmail.com>
Roland Barenbrug [Wed, 10 Aug 2022 18:46:02 +0000 (20:46 +0200)]
ltq-vdsl-vr9-app: skip invalid line status values
DSL_G997_LineStatusData_t defines special invalid values, skip these
metrics.
Signed-off-by: Roland Barenbrug <roland@treslong.com>
[split patch]
Signed-off-by: Andre Heider <a.heider@gmail.com>
Shiji Yang [Sat, 29 Oct 2022 14:06:24 +0000 (22:06 +0800)]
scripts: fix missing character '0' issue in linksys image
In the stock firmware of Linksys, there is a '0' after the crc checksum.
Validated on EA6350V3, EA7300 and EA7300V2's stock images.
Fixes: 892d741259 build: add a script for generating Linksys factory images
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Edward Chow [Wed, 14 Sep 2022 00:15:58 +0000 (08:15 +0800)]
ath79: add support for Linksys EA4500 v3
Add support for the Linksys EA4500 v3 wireless router
Hardware
--------
SoC: Qualcomm Atheros QCA9558
RAM: 128M DDR2 (Winbond W971GG6KB-25)
FLASH: 128M SPI-NAND (Spansion S34ML01G100TFI00)
WLAN: QCA9558 3T3R 802.11 bgn
QCA9580 3T3R 802.11 an
ETH: Qualcomm Atheros QCA8337
UART: 115200 8n1, same as ea4500 v2
USB: 1 single USB 2.0 host port
BUTTON: Reset - WPS
LED: 1x system-LED
LEDs besides the ethernet ports are controlled
by the ethernet switch
MAC Address:
use address(sample 1) source
label 94:10:3e:xx:xx:6f caldata@cal_macaddr
lan 94:10:3e:xx:xx:6f $label
wan 94:10:3e:xx:xx:6f $label
WiFi4_2G 94:10:3e:xx:xx:70 caldata@cal_ath9k_soc
WiFi4_5G 94:10:3e:xx:xx:71 caldata@cal_ath9k_pci
Installation from Serial Console
------------
1. Connect to the serial console. Power up the device and interrupt
autoboot when prompted
2. Connect a TFTP server reachable at 192.168.1.0/24
(e.g. 192.168.1.66) to the ethernet port. Serve the OpenWrt
initramfs image as "openwrt.bin"
3. To test OpenWrt only, go to step 4 and never execute step 5;
To install, auto_recovery should be disabled first, and boot_part
should be set to 1 if its current value is not.
ath> setenv auto_recovery no
ath> setenv boot_part 1
ath> saveenv
4. Boot the initramfs image using U-Boot
ath> setenv serverip 192.168.1.66
ath> tftpboot 0x84000000 openwrt.bin
ath> bootm
5. Copy the OpenWrt sysupgrade image to the device using scp and
install it like a normal upgrade (with no need to keeping config
since no config from "previous OpenWRT installation" could be kept
at all)
# sysupgrade -n /path/to/openwrt/sysupgrade.bin
Note: Like many other routers produced by Linksys, it has a dual
firmware flash layout, but because I do not know how to handle
it, I decide to disable it for more usable space. (That is why
the "auto_recovery" above should be disabled before installing
OpenWRT.) If someone is interested in generating factory
firmware image capable to flash from stock firmware, as well as
restoring the dual firmware layout, commented-out layout for the
original secondary partitions left in the device tree may be a
useful hint.
Installation from Web Interface
------------
1. Login to the router via its web interface (default password: admin)
2. Find the firmware update interface under "Connectivity/Basic"
3. Choose the OpenWrt factory image and click "Start"
4. If the router still boots into the stock firmware, it means that
the OpenWrt factory image has been installed to the secondary
partitions and failed to boot (since OpenWrt on EA4500 v3 does not
support dual boot yet), and the router switched back to the stock
firmware on the primary partitions. You have to install a stock
firmware (e.g. 3.1.6.172023, downloadable from
https://www.linksys.com/support-article?articleNum=148385 ) first
(to the secondary partitions) , and after that, install OpenWrt
factory image (to the primary partitions). After successful
installation of OpenWrt, auto_recovery will be automatically
disabled and router will only boot from the primary partitions.
Signed-off-by: Edward Chow <equu@openmail.cc>
Daniel Golle [Sun, 30 Oct 2022 20:22:06 +0000 (20:22 +0000)]
base-files: bring back nand_do_upgrade_success
Several Broadcom targets were using the nand_do_upgrade_success
shell function which has been removed by commit
e25e6d8e54
("base-files: fix and clean up nand sysupgrade code"). Refactor the
new nand_do_upgrade to bring back nand_do_upgrade_success with the
behavior expected by those users.
Fixes: e25e6d8e54 ("base-files: fix and clean up nand sysupgrade code")
Reported-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
John Audia [Sat, 29 Oct 2022 10:34:51 +0000 (06:34 -0400)]
kernel: bump 5.15 to 5.15.76
All patches automatically rebased.
Build system: x86_64
Build-tested: bcm2711/RPi4B, mt7622/RT3200
Run-tested: bcm2711/RPi4B, mt7622/RT3200
Signed-off-by: John Audia <therealgraysky@proton.me>
John Audia [Sat, 29 Oct 2022 11:28:23 +0000 (07:28 -0400)]
rockchip: armv8: add CONFIG_ARM64_ERRATUM_1742098
5.15.76 introduces a new symbol that applies Cortex-A72 SoCs so enable it[1].
1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/diff/arch/arm64/Kconfig?id=v5.15.76&id2=v5.15.75
Signed-off-by: John Audia <therealgraysky@proton.me>
John Audia [Sat, 29 Oct 2022 11:05:34 +0000 (07:05 -0400)]
mvebu: cortexa72: add CONFIG_ARM64_ERRATUM_1742098
5.15.76 introduces a new symbol that applies Cortex-A72 SoCs so enable it[1].
1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/diff/arch/arm64/Kconfig?id=v5.15.76&id2=v5.15.75
Signed-off-by: John Audia <therealgraysky@proton.me>
John Audia [Sat, 29 Oct 2022 10:54:59 +0000 (06:54 -0400)]
kernel: add # CONFIG_ARM64_ERRATUM_1742098
Introduced with 5.15.76[1]
1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/diff/arch/arm64/Kconfig?id=v5.15.76&id2=v5.15.75
Signed-off-by: John Audia <therealgraysky@proton.me>
John Audia [Wed, 26 Oct 2022 22:31:12 +0000 (18:31 -0400)]
kernel: bump 5.15 to 5.15.75
Removed upstreamed:
bcm27xx/patches-5.15/950-0446-drm-vc4-Fix-timings-for-VEC-modes.patch[1]
Manually rebased:
patches-5.15/950-0600-xhci-quirks-add-link-TRB-quirk-for-VL805.patch
bcm27xx/patches-5.15/950-0606-usb-xhci-add-VLI_TRB_CACHE_BUG-quirk.patch
bcm27xx/patches-5.15/950-0717-usb-xhci-add-a-quirk-for-Superspeed-bulk-OUT-transfe.patch
bcm53xx/patches-5.15/180-usb-xhci-add-support-for-performing-fake-doorbell.patch
All other patches automatically rebased
1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.75&id=
2810061452f9b748b096ad023d318690ca519aa3
Build system: x86_64
Build-tested: bcm2711/RPi4B, mt7622/RT3200
Run-tested: bcm2711/RPi4B, mt7622/RT3200
Signed-off-by: John Audia <therealgraysky@proton.me>
John Audia [Thu, 27 Oct 2022 07:47:53 +0000 (03:47 -0400)]
kernel: add # CONFIG_ARM64_ERRATUM_2441007 symbol
Introduced with 5.15.75.[1]
1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/diff/arch/arm64/Kconfig?id=v5.15.75&id2=v5.15.74
Signed-off-by: John Audia <therealgraysky@proton.me>
John Audia [Sun, 30 Oct 2022 12:32:36 +0000 (08:32 -0400)]
kernel: bump 5.10 to 5.10.152
All patches automatically rebased.
Signed-off-by: John Audia <therealgraysky@proton.me>
John Audia [Sun, 30 Oct 2022 09:38:39 +0000 (05:38 -0400)]
layerscape: armv8_64b: add CONFIG_ARM64_ERRATUM_1742098
5.10.152 introduces a new symbol that applies Cortex-A72 SoCs so enable it[1].
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/diff/arch/arm64/Kconfig?id=v5.10.152&id2=v5.10.151
Signed-off-by: John Audia <therealgraysky@proton.me>
John Audia [Fri, 28 Oct 2022 12:03:27 +0000 (08:03 -0400)]
kernel: bump 5.10 to 5.10.151
All patches automatically rebased.
Signed-off-by: John Audia <therealgraysky@proton.me>
John Audia [Thu, 27 Oct 2022 10:26:25 +0000 (06:26 -0400)]
kernel: bump 5.10 to 5.10.150
Manually rebased:
bcm53xx/patches-5.10/180-usb-xhci-add-support-for-performing-fake-doorbell.patch
All patches automatically rebased.
Signed-off-by: John Audia <therealgraysky@proton.me>
[Move gro_skip in 680-NET-skip-GRO-for-foreign-MAC-addresses.patch to old position]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Chukun Pan [Sun, 18 Sep 2022 15:16:18 +0000 (23:16 +0800)]
mediatek: add Xiaomi Redmi Router AX6000 support
Hardware specification:
SoC: MediaTek MT7986A 4x A53
Flash: ESMT F50L1G41LB 128 MB
RAM: K4A4G165WF-BCWE 512 MB
Ethernet: 4x 10/100/1000 Mbps
WiFi1: MT7976GN 2.4GHz ax 4x4
WiFi2: MT7976AN 5GHz ax 4x4
Button: Mesh, Reset
Flash instructions:
1. Gain ssh and serial port access, see the link below:
https://openwrt.org/toh/xiaomi/redmi_ax6000#installation
2. Use ssh or serial port to log in to the router, and
execute the following command:
nvram set boot_wait=on
nvram set flag_boot_rootfs=0
nvram set flag_boot_success=1
nvram set flag_last_success=1
nvram set flag_try_sys1_failed=8
nvram set flag_try_sys2_failed=8
nvram commit
3. Set a static ip on the ethernet interface of your computer
(e.g. default: ip 192.168.31.100, gateway 192.168.31.1)
4. Download the initramfs image, rename it to initramfs.bin,
and host it with the tftp server.
5. Interrupt U-Boot and run these commands:
setenv mtdparts nmbm0:1024k(bl2),256k(Nvram),256k(Bdata),2048k(factory),2048k(fip),256k(crash),256k(crash_log),112640k(ubi)
saveenv
tftpboot initramfs.bin
bootm
6. After openwrt boots up, use scp or luci web
to upload sysupgrade.bin to upgrade.
Revert to stock firmware:
Restore mtdparts back to default, then use the
vendor's recovery tool (Windows only).
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Rodrigo Balerdi [Wed, 4 May 2022 02:54:58 +0000 (23:54 -0300)]
base-files: verify nand sysupgrade images
For nand sysupgrade image files having tar/gzip/tgz envelopes, verify
envelope integrity before starting sysupgrade.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Rodrigo Balerdi [Tue, 3 May 2022 10:09:33 +0000 (07:09 -0300)]
base-files: accept gzipped nand sysupgrade images
When firmware images only contained compressed kernels and squashfs roots,
uncompressed tar files were a good option. We are now using UBIFS images,
both raw and tarred, as well as ubinized (full UBI partition) images, all
of which benefit greatly from compression.
For example, a raw ubinized backup taken from a running Askey RT4230W REV6
(such full backups can be restored via the LUCI's sysupgrade UI) is over
400 MB, but compresses to less than 10 MB.
This commit adds support for gzipped versions of all file types already
accepted by the nand sysupgrade mechanism, be them raw or tarred.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Rodrigo Balerdi [Tue, 3 May 2022 06:47:43 +0000 (03:47 -0300)]
base-files: fix ubinized nand sysupgrade
It has been reported that ubinized nand sysupgrade fails under certain
circumstances, being unable to detach the existing ubi partition due to
volumes within the partition being mounted.
This is an attempt to solve such issues by unmounting and removing
ubiblock devices and unmounting ubi volumes within the target partition
prior to detaching and formatting it.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Rodrigo Balerdi [Tue, 3 May 2022 06:31:48 +0000 (03:31 -0300)]
base-files: fix and clean up nand sysupgrade code
- Never return from 'nand_do_upgrade', not even in case of errors, as that
would cause execution of sysupgrade code not intended for NAND devices.
- Unify handling of sysupgrade success and failure.
- Detect and report more error conditions.
- Fix outdated/incorrect/unclear comments.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Olliver Schinagl [Thu, 27 Oct 2022 18:53:08 +0000 (20:53 +0200)]
realtek: Fix CRC offloading for rtl83xx
In rtl83xx_set_features we set bit 3 to enable, and bit 4 to disable
checksuming. Looking at rtl93xx_set_features we however see that for
both enable and disable the same bit is used (bit 4). This can't be
right, especially as bit 4 for rtl83xx seems to be Collision threshold
occupying 2 bits. Change this to make this more logical.
Fixes: 9e8d62e42117 ("realtek: enable CRC offloading")
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Christian Marangi [Thu, 27 Oct 2022 23:06:07 +0000 (01:06 +0200)]
ipq806x: disable ea8500 image by default
Linksys EA8500 is currently broken after the kernel 5.15 bump. Disable
compiling it by default from buildbot to prevent brick from the user.
Don't mark it as BROKEN to permit user to compile images and permit devs
to bisect the problem with the users.
The current problem with the device is that the switch is not detected
and we can't comunicate with it via MDIO.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Christian Marangi [Thu, 27 Oct 2022 23:06:07 +0000 (01:06 +0200)]
ipq806x: disable ea8500 image by default
Linksys EA8500 is currently broken after the kernel 5.15 bump. Disable
compiling it by default from buildbot to prevent brick from the user.
Don't mark it as BROKEN to permit user to compile images and permit devs
to bisect the problem with the users.
The current problem with the device is that the switch is not detected
and we can't comunicate with it via MDIO.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Rafał Miłecki [Thu, 27 Oct 2022 20:33:14 +0000 (22:33 +0200)]
bcm4908: add pending BQL support for bcm4908_enet
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rafał Miłecki [Thu, 27 Oct 2022 19:05:20 +0000 (21:05 +0200)]
bcm4908: backport bcm4908_enet fix for NULL dereference
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rafał Miłecki [Thu, 27 Oct 2022 16:57:39 +0000 (18:57 +0200)]
bcm4908: optimize Ethernet driver by using build_skb()
This should slightly improve performance thanks to the better cache
usage.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Jan Hoffmann [Tue, 25 Oct 2022 22:20:05 +0000 (00:20 +0200)]
realtek: use assisted learning on CPU port
L2 learning on the CPU port is currently not consistently configured and
relies on the default configuration of the device. On RTL83xx, it is
disabled for packets transmitted with a TX header, as hardware learning
corrupts the forwarding table otherwise. As a result, unneeded flooding
of traffic for the CPU port can already happen on some devices now. It
is also likely that similar issues exist on RTL93xx, which doesn't have
a field to disable learning in the TX header.
To address this, disable hardware learning for the CPU port globally on
all devices. Instead, enable assisted learning to let DSA write FDB
entries to the switch.
For now, this does not sync local/bridge entries to the switch. However,
support for that was added in Linux 5.14, so the next switch to a newer
kernel version is going to fix this.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Jan Hoffmann [Tue, 25 Oct 2022 22:20:04 +0000 (00:20 +0200)]
realtek: set up L2 table entries properly
Initialize the data structure using memset to avoid the possibility of
writing garbage values to the hardware.
Always set a valid entry type, which should fix writing unicast entries
on RTL930x.
For unicast entries, set the is_static flag to prevent the switch from
aging them out.
Also set the rvid field for unicast entries. This is not strictly
necessary, as the switch fills it in automatically from a non-zero vid.
However, this makes the code consistent with multicast entry setup.
While at it, reorder the statements and fix some style issues (double
space, comma instead of semicolon at end of statement). Also remove the
unneeded priv parameter and debug print for the multicast entry setup
function.
Fixes: cde31976e37 ("realtek: Add support for Layer 2 Multicast")
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Bob Cantor [Sun, 4 Jul 2021 17:26:46 +0000 (03:26 +1000)]
base-files: wifi: for wifi reconf, scan_wifi after network reload
Commit
e8b542960921 included an unintended change and we now call
scan_wifi before a network reload.
Restore the original behaviour and call scan_wifi only after a network
reload.
Fixes: e8b542960921 ("base-files: wifi: tidy up the reconf code")
Signed-off-by: Bob Cantor <bobc@confidesk.com>
Bob Cantor [Sun, 4 Jul 2021 17:03:58 +0000 (03:03 +1000)]
base-files: wifi: for wifi up, scan_wifi after network reload
Commit
b82cc8071366 included an unintended change and we now call
scan_wifi before a network reload.
Restore the original behaviour and call scan_wifi only after a network
reload.
Fixes: b82cc8071366 ("base-files: wifi: swap the order of some ubus calls")
Signed-off-by: Bob Cantor <bobc@confidesk.com>
Christian Marangi [Tue, 25 Oct 2022 02:56:16 +0000 (04:56 +0200)]
realtek: 5.10: refresh kernel patches
Refresh kernel patches for realtek 5.10 kernel
Refreshed patch:
- 300-mips-add-rtl838x-platform.patch
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Davide Fioravanti [Tue, 4 Oct 2022 21:20:39 +0000 (23:20 +0200)]
ipq40xx: convert to DSA and enable Netgear Orbi devices
Convert to DSA and enable again Netgear Orbi devices:
- RBR50
- RBS50
- SRR60
- SRS60
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
Christian Marangi [Mon, 24 Oct 2022 21:08:06 +0000 (23:08 +0200)]
generic: 5.15: add missing CMDLINE_OVERRIDE patch
This patch was wrongly dropped with the assumption that it was moved to
generic. This wasn't the case and caused the malfunction of the Asrock
G10 router.
Reintroduce it to fix Asrock G10 functionality.
Fixes: 8cc2caed58e7 ("ipq806x: 5:15: add testing kernel version")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Christian Marangi [Sat, 22 Oct 2022 14:58:19 +0000 (16:58 +0200)]
ipq806x: 5.15: drop mmc-ddr-1_8v from sdcc1 node
Zyxel NGB6817 is the only router that use mmc for rootfs. Upstream
kernel dtsi have mmc-ddr-1_8v enabled for sddc1. This is wrong as mmc on
ipq806x is supplied by a fixed 3.3v regulator and can't operate at 1.8v.
This cause the sddc1 to malfunction and cause kernel panic.
In old 5.15 version this was disabled but it was put in addition to many
other changes so it was dropped silently. Restore this patch to fix
working condition of such router.
Fixes: 88bf652 ("ipq806x: 5.15: replace dtsi patches with upstream version")
Fixes: #11000
Tested-by: Hendrik Koerner <koerhen@web.de>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Christian Marangi [Thu, 20 Oct 2022 14:53:01 +0000 (16:53 +0200)]
ipq806x: 5.15: revert unwanted DSA conversion for ASRock G10
In refreshing DTS to the upstream version an unwanted change slipped in
the commit. The ASRock G10 dts got converted to DSA without any support.
Revert this to swconfig driver to restore normal functionality.
Fixes: 88bf6525251f ("ipq806x: 5.15: replace dtsi patches with upstream version")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Christian Marangi [Fri, 21 Oct 2022 16:56:08 +0000 (18:56 +0200)]
ipq806x: 5.15: backport qcom_nandc patch for unprotected spare data fix
We currently ignore ret of the nandc partition parser if unprotected
spare data is true. This is the case for ipq806x nand.
Backport patch that fix this error and correctly handle error from
partition parser.
Fixes: ae6a63bc97cf ("ipq806x: 5.15: replace nandc patch with upstream version")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Christian Marangi [Thu, 20 Oct 2022 14:48:16 +0000 (16:48 +0200)]
generic: 5.15: backport smempart parser fixup patch with EPROBE_DEFER error
Backport patch from kernel 5.15 that mute error on EPROBE_DEFER with
smempart parser.
This parser require the smem device to be probed first and currently it
may happen that mtd gets probed before the smem device causing an error
on the smempart parser. This error may be confusing and should be muted.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Christian Marangi [Thu, 20 Oct 2022 14:44:56 +0000 (16:44 +0200)]
generic: 5.15: backport qcom smem patch for reserved-space support
In new kernel version from 5.16, smem node can be declared directly in
the reserved-space node. Upstream ipq806x (and to-be-merged) ipq807x
allign to this new implementation. Backport this patch to kernel 5.15 to
fix support for smem parser for ipq806x target.
Fixes: 88bf6525251f ("ipq806x: 5.15: replace dtsi patches with upstream version")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Christian Marangi [Sat, 22 Oct 2022 13:43:47 +0000 (15:43 +0200)]
generic: 5.15: move not backport patch to pending dir
Move patch wrongly placed in backport dir to pending dir as they still
didn't got merged upstream.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Christian Marangi [Fri, 21 Oct 2022 22:24:49 +0000 (00:24 +0200)]
generic: 5.15: move MGLRU patches from pending to backport
Move MGLRU patches from pending to backport as they got merged upstream.
These are direct porting from one of the dev so it's better to just move
than trying to backport them again from upstream.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Christian Marangi [Fri, 21 Oct 2022 21:55:37 +0000 (23:55 +0200)]
generic: 5.15: move mvebu aardvark patch from pending to backport
Move mvebu aardvark patch from pending to backport as they got merged
upstream.
One additional patch is needed as a later fixup for it.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Christian Marangi [Fri, 21 Oct 2022 21:36:04 +0000 (23:36 +0200)]
generic: 5.15: move ZTE MF286D modem patch from pending to backport
Move ZTE MF286D modem patch from pending to backport as it was merged
upstream.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Christian Marangi [Fri, 21 Oct 2022 21:29:39 +0000 (23:29 +0200)]
generic: 5.15: move bluetooth mt79 usb id patch from pending to backport
Move bluetooth mt79 usb id patch from pending to backport as it got
merged upstream.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Christian Marangi [Fri, 21 Oct 2022 21:19:44 +0000 (23:19 +0200)]
generic: 5.15: move mtk eth soc patch from pending to backport
Move mtk eth soc patch from pending to backport as it got merged
upstream.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Christian Marangi [Fri, 21 Oct 2022 21:08:54 +0000 (23:08 +0200)]
generic: 5.15: move sfp HALNy patch from pending to backport
Move sfp HALNy patch from pending to backport as they got merged
upstream. The patch was reordered and one was squashed in the upstream
variant.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Christian Marangi [Fri, 21 Oct 2022 20:43:07 +0000 (22:43 +0200)]
generic: 5.15: move pending xtx nand patch from pending to backport
Move pending xtx nand patch from pending to backport as it got merged
upstream.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Christian Marangi [Fri, 21 Oct 2022 20:37:06 +0000 (22:37 +0200)]
generic: 5.15: move dtc drop interrupt check from pending to backport
Move dtc drop interrupto check from pending to backport as it got merged
upstream.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Christian Marangi [Fri, 21 Oct 2022 20:14:22 +0000 (22:14 +0200)]
generic: 5.15: move MIPS cpuinfo patch from pending to backport
Move MIPS cpuinfo patch from pending to backport as it got merged
upstream.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Andre Heider [Thu, 20 Oct 2022 10:52:17 +0000 (12:52 +0200)]
mac80211: fix masking nested A-MSDU support for mesh
CONFIG_MAC80211_MESH isn't defined for this package, rendering the patch
useless. Match protecting the access of sta_info.mesh with the very same
define declaring it.
Fixes
45109f69a6 "mac80211: fix compile error when mesh is disabled"
Signed-off-by: Andre Heider <a.heider@gmail.com>
Felix Fietkau [Mon, 24 Oct 2022 18:43:14 +0000 (20:43 +0200)]
mac80211: use KERNEL_MAKEOPTS instead of KERNEL_MAKE_FLAGS
Fixes issues with disabling stack validation on non-linux systems
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Mon, 24 Oct 2022 16:16:56 +0000 (18:16 +0200)]
button-hotplug: simplify build
Remove unnecessary kconfig junk
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Shiji Yang [Sat, 17 Sep 2022 10:50:00 +0000 (18:50 +0800)]
ramips: add missing WAN LED for Xiaomi Mi Router 4A / 4C
The blue WAN LED connected to GPIO37 is missing, so re-add it.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Hauke Mehrtens [Sat, 22 Oct 2022 14:16:55 +0000 (16:16 +0200)]
toolchain: gcc: Remove gcc 10.x support
This compiler is old and was never used by default in OpenWrt.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sat, 22 Oct 2022 14:15:16 +0000 (16:15 +0200)]
toolchain: gcc: Remove gcc 8.x support
This compiler is old and not used by OpenWrt for some time now.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sat, 15 Oct 2022 09:31:42 +0000 (11:31 +0200)]
mac80211: Update to version 5.15.74-1
This updates mac80211 to version 5.15.74-1 which is based on kernel
5.15.74.
The removed patches were applied upstream.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Sander Vanheule [Fri, 9 Sep 2022 19:25:17 +0000 (21:25 +0200)]
realtek: consistently flood RMA frames
The switches support different actions for incoming ethernet multicast
frames with Reserved Multicast Addresses (01-80-C2-00-00-{01-2F}). The
current code will set the 2-bit action field to FLOOD (0x3) for most
classes, but the highest bit is always unset for the relevant control
registers. This means the DROP (0x1) action being used for these
classes; whatever class the MSB happens to be in.
For RTL838x, this results in {20,23-2F} frames being dropped, instead of
flooding all ports. On other switch generations, {0F,1F,2F} frames are
dropped. This is inconsistent, and appears to be a mistake. Remove this
inconsistency by flooding all multicast frames with RMA addresses.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Sander Vanheule [Fri, 9 Sep 2022 17:35:23 +0000 (19:35 +0200)]
realtek: remove RTL839x path in RTL838x multicast
The multicast setup function rtl838x_eth_set_multicast_list() checks if
the current SoC is a RTL839x family device. However, the function is
only included in the RTL838x ops table, so this path should never be
taken, making this dead code. rtl839x_eth_set_multicast_list() is
already present in the RTL839x ops table, so it should be safe to remove
this branch.
While touching the code, also re-sort the functions to match sorting
elsewhere, with rtl838x coming before rtl839x.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Jan Hoffmann [Fri, 14 Oct 2022 21:06:17 +0000 (23:06 +0200)]
realtek: reduce excessive logging for FDB operations
Currently several messages at KERN_INFO level are printed for every FDB
del/dump operation. This can cause a significant slowdown for example
while using "bridge fdb", and may even trigger a watchdog.
Remove most of these log messages, as the new L2 table debugfs node
should be a good replacement. Change the remaining messages to
KERN_DEBUG level.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Jan Hoffmann [Fri, 14 Oct 2022 21:06:16 +0000 (23:06 +0200)]
realtek: add debugfs node for L2 table
This allows to view all unicast and multicast entries that are currently
in the L2 hash table and the CAM.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Jan Hoffmann [Fri, 14 Oct 2022 21:06:14 +0000 (23:06 +0200)]
realtek: avoid busy waiting for RTL839x PHY read/write
Switch to a polling implementation similar to the one for RTL838x, to
allow other kernel tasks to run while waiting.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Markus Stockhausen [Mon, 3 Oct 2022 13:15:06 +0000 (15:15 +0200)]
realtek: disable otto timer for RTL93xx targets
The new timer is not yet ready for all targets. Avoid interactive
questions during build
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
[rename symbol to CONFIG_REALTEK_OTTO_TIMER]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Markus Stockhausen [Mon, 3 Oct 2022 12:50:17 +0000 (14:50 +0200)]
realtek: timer driver: activate for RTL839X devices
Use the new timer driver for the RTL839X devices and remove the
no longer needed modules.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
[correct timer compatible order, update selected symbols]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Markus Stockhausen [Mon, 3 Oct 2022 12:49:35 +0000 (14:49 +0200)]
realtek: timer driver: activate for RTL838X devices
Use the new timer driver for the RTL838X devices. Remove the no
longer needed modules.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
[correct timer compatible order, update selected symbols]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Markus Stockhausen [Mon, 3 Oct 2022 12:47:18 +0000 (14:47 +0200)]
realtek: timer driver: documentation
Provide some helpful information about the devicetree configuration of
our new driver
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
[correct compatible order in examples]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Markus Stockhausen [Mon, 3 Oct 2022 12:45:21 +0000 (14:45 +0200)]
realtek: resurrect timer driver
Now that we provide a clock driver for the Reltek SOCs the CPU frequency might
change on demand. This has direct visible effects during operation
- the CEVT 4K timer is no longer a stable clocksource
- after CPU frequencies changes time calculation works wrong
- sched_clock falls back to kernel default interval (100 Hz)
- timestamps in dmesg have only 2 digits left
[ 0.000000] sched_clock: 32 bits at 100 Hz, resolution 10000000ns, wraps ...
[ 0.060000] pid_max: default: 32768 minimum: 301
[ 0.070000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.070000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.080000] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build
[ 0.090000] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, ...
Looking around where we can start the CEVT timer for RTL930X is a good basis.
Initially it was developed as a clocksource driver for the broken timer in that
specific SOC series. Afterwards it was shifted around to the CEVT location,
got SMP enablement and lost its clocksource feature. So we at least have
something to copy from. As the timers on these devices are well understood
the implementation follows this way:
- leave the RTL930X implementation as is
- provide a new driver for RTL83XX devices only
- swap RTL930X driver at a later time
Like the clock driver this patch contains a self contained module that is SOC
independet and already provides full support for the RTL838X, RTL839X and
RTL930X devices. Some of the new (or reestablished) features are:
- simplified initialization routines
- SMP setup with CPU hotplug framework
- derived from LXB clock speed
- supplied clocksource
- dedicated register functions for better readability
- documentation about some caveats
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
[remove unused header includes, remove old CONFIG_MIPS dependency, add
REALTEK_ prefix to driver symbol]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Nick Hainke [Fri, 21 Oct 2022 12:48:58 +0000 (14:48 +0200)]
readline: update to 8.2
Release Announcement:
https://lists.gnu.org/archive/html/info-gnu/2022-09/msg00013.html
Signed-off-by: Nick Hainke <vincent@systemli.org>
Nick Hainke [Sun, 23 Oct 2022 12:26:20 +0000 (14:26 +0200)]
gdb: add patch adding support for readline 8.2
Add "001-Add-support-for-readline-8.2.patch" adding support for readline
8.2.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Daniel Golle [Sun, 23 Oct 2022 15:21:26 +0000 (16:21 +0100)]
tools/mkimage: bring back removed patches
Patches for mtk_image supporting newer SoCs have been dropped in the
process of updating mkimage to U-Boot 2022.10. While it is true that
the patches have been merged upstream a while ago, they were not merged
in time to be part of the U-Boot 2022.10 release.
See also commit
537b423d9f ("uboot-mediatek: update to U-Boot 2022.10")
which explicitly mentions that.
Fixes: 6e245777bd ("tools/mkimage: update to 2022.10")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Brian Norris [Sat, 22 Oct 2022 20:00:38 +0000 (13:00 -0700)]
ipq40xx: Convert Google Wifi to DSA, reenable
Undo parts of these:
116feb4a1cad ipq40xx: remove non-converted network configs
db19efee9512 ipq40xx: disable boards not converted to DSA
Reintroduce the DT paths /soc/edma@
c080000/gmac{0,1}, because the stock
bootloader has memorized them (instead of following aliases); then plug
the MAC address back in via 05_set_iface_mac_ipq40xx.sh, since the
'local-mac-address' property is no longer in the correct node.
Cc: David Bauer <mail@david-bauer.net>
Cc: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Nick Hainke [Fri, 21 Oct 2022 12:23:47 +0000 (14:23 +0200)]
ksmbd: update to 3.4.6
Release Announcement:
https://github.com/cifsd-team/ksmbd/releases/tag/3.4.6
Remove upstreamed:
- 10-fix-build-on-kernel-5.15.52-or-higher.patch
Signed-off-by: Nick Hainke <vincent@systemli.org>
Jack Chen [Fri, 14 Oct 2022 07:58:46 +0000 (15:58 +0800)]
ipq40xx: convert to DSA and enable mobipromo,cm520-79f
Convert to DSA and enable the MobiPromo CM520-79F device again.
Signed-off-by: Jack Chen <redchenjs@live.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Pavel Kamaev [Sun, 16 Oct 2022 18:27:47 +0000 (21:27 +0300)]
ath79: fix reference clock for RouterBoard 912UAG
This fixes reference clock frequency of RB912. 25 MHz frequency leads
to system clock running too fast, uptime incrementing too fast and
delays (like `sleep 10`) returning too early.
Board has quartz with NSK 3KHAA Z 40 000 marking.
Signed-off-by: Pavel Kamaev <pavel@kamaev.me>
David Bentham [Mon, 17 Oct 2022 14:43:29 +0000 (15:43 +0100)]
ramips: fix WAN mac address allocation for Unielec 01 and 06 models
Manufacturer has predetermined mac address values for lan and wan ports.
This change keeps inline with other mt7621 devices mac address allocation
from factory mtd partition.
Example from hexdump output:
0xe000 0x6 (lan) - 0xe006 0x6 (wan)
0000e000 70 b3 d5 10 02 96 70 b3 d5 10 02 95 ff ff ff ff
Previous change had created an overlapping mac address situation as it
would increment by one based on the lan mac address location found in the
factory partition, which would sometimes increment to the same as the
mt7603 wifi chip.
Tested on Unielec u7621-01 model
Signed-off-by: David Bentham <db260179@gmail.com>
Robert Senderek [Mon, 17 Oct 2022 19:15:35 +0000 (21:15 +0200)]
ramips: rt3883: enable lzma-loader for Belkin F9K1109v1
Fixes boot loader LZMA decompression issues
Fixes: #10968
Signed-off-by: Robert Senderek <robert.senderek@10g.pl>
Alex Khodin [Fri, 21 Oct 2022 17:47:38 +0000 (17:47 +0000)]
ramips: mt7621: enable lzma-loader for Asus RT-N56U-B1
Fixes boot loader LZMA decompression issues.
Without this change the board end up in a boot loop.
Signed-off-by: Alex Khodin <mxktz1@gmail.com>
Chukun Pan [Thu, 2 Jun 2022 15:01:29 +0000 (23:01 +0800)]
ramips: add A-040W-Q alternative name for MSG1500 X.00
The hardware of Nokia A-040W-Q and RAISECOM MSG1500 X.00 are
exactly the same, both of which are customized by operators.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Chukun Pan [Wed, 1 Jun 2022 15:16:04 +0000 (23:16 +0800)]
kernel: move mac-address-ascii patches to generic
This enables other targets to use the mac-address-ascii
feature.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Aleksander Jan Bajkowski [Wed, 5 Oct 2022 21:05:26 +0000 (23:05 +0200)]
lantiq: add 6.1 tag to upstream patch
Add 6.1 tag to upstream patch now that 6.1 got tagged. This permits to
track patch in a better way and directly drop them on kernel bump.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Hauke Mehrtens [Sat, 22 Oct 2022 23:43:36 +0000 (01:43 +0200)]
tools/genext2fs: Add dependency to libtool
This fixes the following build error:
./autogen.sh: line 13: aclocal: command not found
Fixes: b6d29af9475f ("tools/genext2fs: update to 1.5.0")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Nick Hainke [Sun, 21 Aug 2022 07:33:46 +0000 (09:33 +0200)]
tools/genext2fs: update to 1.5.0
Update to latest version.
Remove patches:
- 100-c99_scanf.patch
- 200-autoconf.patch
- 300-blocksize-creator.patch
- 400-byteswap_fix.patch
Signed-off-by: Nick Hainke <vincent@systemli.org>
Nick Hainke [Sun, 21 Aug 2022 06:43:52 +0000 (08:43 +0200)]
tools/genext2fs: switch to codeload.github.com
As written on the genext2fs.sourceforge.net page:
"If you want bugfixes and nicer features though, you will have to grab
the source from github and build it yourself."
This commit switches the download from sourceforge to
codeload.github.com.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Nick Hainke [Fri, 21 Oct 2022 21:24:29 +0000 (23:24 +0200)]
tools/dwarves: update to 1.24
Release Notes:
https://lwn.net/Articles/905738/
Switch to https "fedorapeople.org"-mirror. Use $(AUTORELEASE).
Signed-off-by: Nick Hainke <vincent@systemli.org>
Nick Hainke [Fri, 21 Oct 2022 20:14:12 +0000 (22:14 +0200)]
tools/bash: update to 5.2
Release Notes:
https://lists.gnu.org/archive/html/bug-bash/2022-09/msg00056.html
Signed-off-by: Nick Hainke <vincent@systemli.org>
Nick Hainke [Fri, 21 Oct 2022 20:41:06 +0000 (22:41 +0200)]
tools/zlib: update to 1.2.13
Switch to "https github.com" for downloading source files.
Release Announcements:
https://github.com/madler/zlib/releases/tag/v1.2.13
Signed-off-by: Nick Hainke <vincent@systemli.org>
Nick Hainke [Fri, 21 Oct 2022 20:23:47 +0000 (22:23 +0200)]
tools/bc: update to 1.07.1
Changes:
Fixed ibase extension causing problems for read()
Fixed parallel make problem.
Remove the "003-bc-fix-hang.patch" because the hang is fixed upstream.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Nick Hainke [Fri, 21 Oct 2022 20:01:48 +0000 (22:01 +0200)]
tools/mtools: update to 4.0.41
Release Notes:
https://lists.gnu.org/archive/html/info-gnu/2022-09/msg00011.html
Signed-off-by: Nick Hainke <vincent@systemli.org>
Nick Hainke [Fri, 21 Oct 2022 20:06:49 +0000 (22:06 +0200)]
tools/xz: update to 5.2.7
Update to latest version.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Nick Hainke [Fri, 21 Oct 2022 20:53:58 +0000 (22:53 +0200)]
tools/mkimage: update to 2022.10
Remove upstreamed patches:
- 020-tools-mtk_image-split-gfh-header-verification-into-a.patch
- 021-tools-mtk_image-split-the-code-of-generating-NAND-he.patch
- 022-tools-mtk_image-add-support-for-nand-headers-used-by.patch
Refreshed manually:
- 030-allow-to-use-different-magic.patch
Signed-off-by: Nick Hainke <vincent@systemli.org>
Nick Hainke [Wed, 5 Oct 2022 10:37:47 +0000 (12:37 +0200)]
iproute2: update to 6.0.0
Release Notes:
https://lore.kernel.org/netdev/
20221004082610.
56b04719@hermes.local/t/
Remove upstreamed patch:
- 010-ipstats-Add-param.h-for-musl.patch
Refreshed:
- 140-keep_libmnl_optional.patch
- 145-keep_libelf_optional.patch
- 150-keep_libcap_optional.patch
- 155-keep_tirpc_optional.patch
- 170-ip_tiny.patch
- 190-fix-nls-rpath-link.patch
- 200-drop_libbsd_dependency.patch
- 300-selinux-configurable.patch
Signed-off-by: Nick Hainke <vincent@systemli.org>
Nick Hainke [Mon, 26 Sep 2022 05:22:08 +0000 (07:22 +0200)]
thc-ipv6: update to 3.8
Remove upstreamed patches:
- 000-cflags_override.patch
Manually refresh patches:
- 100-no-ssl.patch
Add patches:
- 101-remove-march-native.patch
Add THC_APPLETS:
- toobigsniff6
- flood_unreach6
- connect6
Signed-off-by: Nick Hainke <vincent@systemli.org>
Nick Hainke [Sun, 16 Oct 2022 20:10:01 +0000 (22:10 +0200)]
gettext-full: update to 0.21.1
Release Announcement:
https://lists.gnu.org/archive/html/info-gnu/2020-07/msg00009.html
Further, refresh 001-autotools.patch and manually refresh 010-m4.patch.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Nick Hainke [Sun, 16 Oct 2022 18:19:01 +0000 (20:19 +0200)]
libbsd: update to 0.11.7
Changes:
084911c Release libbsd 0.11.7
3538d38 man: Discourage using the library in non-overlay mode
03fccd1 include: Adjust reallocarray() per glibc adoption
6b6e686 include: Adjust arc4random() per glibc adoption
da1f45a include: explicit_bzero() requires _DEFAULT_SOURCE
2f9eddc include: Simplify glibc version dependent macro handling
28298ac doc: Switch references from pkg-config to pkgconf
ef981f9 doc: Add missing empty line to separate README sections
6928d78 doc: Refer to the main git repository as primary
d586575 test: Fix explicit_bzero() test on the Hurd
be327c6 fgetwln: Add comment about lack of getwline(3) for recommendation
a14612d setmode: Dot not use saveset after free
f4baceb man: Rewrite gerprogname(3bsd) from scratch
f35c545 man: Lowercase man page title
b466b14 man: Document that some arc4random(3) functions are now in glibc 2.36
1f6a48b Sync arc4random(3) implementation from OpenBSD
873639e Fix ELF support for big endian SH
c9c78fd man: Use -compact also for alternative functions in libbsd(7)
5f21307 getentropy: Fix function cast for getauxval()
Signed-off-by: Nick Hainke <vincent@systemli.org>
projects / openwrt / staging / stintel.git / log