Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-next-2.6 into for-davem

Conflicts:
drivers/net/wireless/iwlwifi/iwl-core.c
drivers/net/wireless/rt2x00/rt2x00queue.c
drivers/net/wireless/rt2x00/rt2x00queue.h

inet: constify ip headers and in6_addr

Add const qualifiers to structs iphdr, ipv6hdr and in6_addr pointers
where possible, to make code intention more obvious.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fix hw_features ethtool_ops->set_flags compatibility

__ethtool_set_flags() was not taking into account features set but not
user-toggleable.

Since GFLAGS returns masked dev->features, EINVAL is returned when
passed flags differ to it, and not to wanted_features.

Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

tg3: Add additional EEE messaging

This patch adds link messages and an item to the sign-on banner to make
EEE status more visible.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tg3: Add macro for SMDSP toggling

A common AUX CTRL operation in the driver is to enable and disable the
SMDSP.  This patch consolidates the code so that the details of the
operation are in one place.  This patch also adds code to make sure the
SMDSP is enabled before executing code that relies on it.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tg3: Add write accessor for AUX CTRL phy reg

This patch adds a write accessor for the aux ctrl phy register.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tg3: Add read accessor for AUX CTRL phy reg

This patch adds a read accessor for the aux ctrl register.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tg3: Move phy accessor functions higher

Phy accessor functions should live closer to where the base phy read /
write routines are.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tg3: Only allow phy ioctls while netif_running

When tg3 was new, phy accesses through ioctl were allowable at any time.
Then, the driver started shutting down the phy when the device was
closed.  Phy accesses would be allowed when the driver first attached to
the device, but then would be forbidden after the device had been up'd
and down'd.  After that, management firmware made it illegal to access
the phy unless the driver "owned" the device.  Now that most firmware
is being moved over to the APE, it is less clear when phy accesses are
safe.

While it is possible to attempt to identify these conditions and code
the driver to navigate through the pitfalls, it could be perplexing to
the admin why phy accesses work in some cases and not others.  This
patch brings some uniformity to the problem by only allowing phy
accesses while the driver has control of the device.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tg3: Nullify RSS for loopback test

The loopback test assumes all traffic goes to the first rx queue.  There
is a 1 in 4 chance this won't be true if RSS is enabled though.  This
patch reprograms the RSS indirection table to route all rx packets to
the first queue.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tg3: Adjust rx prod ring bd replenish thresholds

The oldest tg3 devices had large rx producer ring BD caches.  Back then,
it made sense to make the BD cache replenish threshold only a function
of the number of rx buffers posted by the driver.  Since then, the BD
cache sizes have shrunk to 25% of their original size and, in some
cases, the ring sizes have quadrupled in size.  Under such conditions,
static BD cache replenish thresholds no longer match the hardware
constraints.

This patch attempts to factor in the BD cache size into the bd cache
replenish strategy, taking the existing hardware bugs into account.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tg3: Workaround rx_discards stat bug

The 5717, 5718, 5719 A0, and 5720 A0 has a bug where the rx_discards
statistic counter will increment when dropping unwanted multicast
frames.  This patch works around the problem by attempting to
recreate the data using other means.  The resulting value will not be
accurate, but it can still serve as a problem indicator.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mv643xx_eth: Fix build regression.

From Stephen Rothwell:

--------------------
After merging the final tree, today's linux-next build (powerpc chrp32_defconfig)
failed like this:

drivers/net/mv643xx_eth.c: In function 'port_start':
drivers/net/mv643xx_eth.c:2250: error: 'dev' undeclared (first use in this function)

Caused by commit aad59c431b77 ("net: mv643xx: convert to hw_features").
--------------------

Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: implement event notification SCTP_SENDER_DRY_EVENT

This patch implement event notification SCTP_SENDER_DRY_EVENT.
SCTP Socket API Extensions:

  6.1.9. SCTP_SENDER_DRY_EVENT

  When the SCTP stack has no more user data to send or retransmit, this
  notification is given to the user. Also, at the time when a user app
  subscribes to this event, if there is no data to be sent or
  retransmit, the stack will immediately send up this notification.

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: change auth event type name to SCTP_AUTHENTICATION_EVENT

This patch change the auth event type name to SCTP_AUTHENTICATION_EVENT,
which is based on API extension compliance.

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: implement socket option SCTP_GET_ASSOC_ID_LIST

This patch Implement socket option SCTP_GET_ASSOC_ID_LIST.
SCTP Socket API Extension:

  8.2.6. Get the Current Identifiers of Associations
         (SCTP_GET_ASSOC_ID_LIST)

  This option gets the current list of SCTP association identifiers of
  the SCTP associations handled by a one-to-many style socket.

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: move chunk from retransmit queue to abandoned list

If there is still data waiting to retransmit and remain in
retransmit queue, while doing the next retransmit, if the
chunk is abandoned, we should move it to abandoned list.

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: make heartbeat information in sctp_make_heartbeat()

Make heartbeat information in sctp_make_heartbeat() instead
of make it in sctp_sf_heartbeat() directly for common using.

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: fix to check the source address of COOKIE-ECHO chunk

SCTP does not check whether the source address of COOKIE-ECHO
chunk is the original address of INIT chunk or part of the any
address parameters saved in COOKIE in CLOSED state. So even if
the COOKIE-ECHO chunk is from any address but with correct COOKIE,
the COOKIE-ECHO chunk still be accepted. If the COOKIE is not from
a valid address, the assoc should not be established.

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: handle ootb packet in chunk order as defined

Changed the order of processing SHUTDOWN ACK and COOKIE ACK
refer to section 8.4:Handle "Out of the Blue" Packets.

SHUTDOWN ACK chunk should be processed before processing
"Stale Cookie" ERROR or a COOKIE ACK.

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: bail from sctp_endpoint_lookup_assoc() if not bound

The sctp_endpoint_lookup_assoc() function uses a port hash
to lookup the association and then checks to see if any of
them are on the current endpoint.  However, if the current
endpoint is not bound, there can't be any associations on
it, thus we can bail early.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: remove completely unsed EMPTY state

SCTP does not SCTP_STATE_EMPTY and we can never be in
that state.  Remove useless code.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: remove redundant check when walking through a list of TLV parameters

When  pos.v <= (void *)chunk + end - ntohs(pos.p->length) and
ntohs(pos.p->length) >= sizeof(sctp_paramhdr_t) these two expressions are all true,
pos.v <= (void *)chunk + end - sizeof(sctp_paramhdr_t) *must* be true.

This patch removes this kind of redundant check.
It's same to  _sctp_walk_errors macro.

Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: check invalid value of length parameter in error cause

RFC4960, section 3.3.7 said:
 If an endpoint receives an ABORT with a format error or no TCB is
 found, it MUST silently discard it.

When an endpoint receives ABORT that parameter value is invalid,
drop it.

Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: check parameter value of length in ERROR chunk

When an endpoint receives ERROR that parameter value is invalid,
send an ABORT to peer with a Protocol Violation error code.

Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: tun: convert to hw_features

This changes offload setting behaviour to what I think is correct:
 - offloads set via ethtool mean what admin wants to use (by default
   he wants 'em all)
 - offloads set via ioctl() mean what userspace is expecting to get
   (this limits which admin wishes are granted)
 - TUN_NOCHECKSUM is ignored, as it might cause broken packets when
   forwarded (ip_summed == CHECKSUM_UNNECESSARY means that checksum
   was verified, not that it can be ignored)

If TUN_NOCHECKSUM is implemented, it should set skb->csum_* and
skb->ip_summed (= CHECKSUM_PARTIAL) for known protocols and let others
be verified by kernel when necessary.

TUN_NOCHECKSUM handling was introduced by commit
f43798c27684ab925adde7d8acc34c78c6e50df8:

    tun: Allow GSO using virtio_net_hdr

Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: xen-netback: convert to hw_features

Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: qlcnic: convert to hw_features

Bit more than minimal conversion. There might be some issues because
of qlcnic_set_netdev_features() if it's called after netdev init.

Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ibmveth: convert to hw_features

A minimal conversion.

ibmveth_set_csum_offload() can be folded into ibmveth_set_features()
and adapter->rx_csum removed - left for later cleanup.

Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: pch_gbe: convert to hw_features

This also fixes bug in xmit path, where TX checksum offload state was used
instead of skb->ip_summed to decide if the offload was needed.

Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: infiniband/ulp/ipoib: convert to hw_features

Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: s390: convert to hw_features

options.large_send was easy to get rid of. options.checksum_type has deeper
roots so is left for later cleanup.

Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: infiniband/hw/nes: convert to hw_features

Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

Staging: convert hv network driver to hw_features

Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: batman-adv: remove rx_csum ethtool_ops

Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: remove ethtool_ops->set_sg

Remove set_sg from DSA slave ethtool_ops. Features inheritance looks
broken/not fully implemented anyway.

Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: Release all routes when processing acks ADD_IP or DEL_IP

When processing an ACK for ADD_IP parameter, we only release
the routes on non-active transports.  This can cause a wrong
source address to be used.  We can release the routes and
cause new route lookups and source address selection so that
new addresses can be used as source.  Additionally, we don't need
to lookup routes for all transports at the same time.  We can let
the transmit code path update the cached route when the transport
actually sends something.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: Allow bindx_del to accept 0 port

We allow 0 port when adding new addresses.  It only
makes sence to allow 0 port when removing addresses.
When removing the currently bound port will be used
when the port in the address is set to 0.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: teach CACC algorithm about removed transports

When we have have to remove a transport due to ASCONF, we move
the data to a new active path.  This can trigger CACC algorithm
to not mark that data as missing when SACKs arrive.  This is
because the transport passed to the CACC algorithm is the one
this data is sitting on, not the one it was sent on (that one
may be gone).  So, by sending the original transport (even if
it's NULL), we may start marking data as missing.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: use memdup_user to copy data from userspace

Use common function to simply code.

Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: kill abandoned SCTP_CMD_TRANSMIT command

Remove SCTP_CMD_TRANSMIT command as it never be used.

Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: use common head of addr parameter to access member in addr-unrelated code

The 'p' member of struct sctp_paramhdr is common part for
IPv4 addr parameter and IPv6 addr parameter in union sctp_addr_param.

For addr-related code, use specified addr parameter.
Otherwise, use common header to access type/length member.

Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: fix the comment of sctp_sf_violation_paramlen()

Update the comment about sctp_sf_violation_paramlen() to be
more precise.

Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: delete unused macro definition of sctp_chunk_is_control

The macro never be used.
And if needed, can use !sctp_chunk_is_data instead of.

Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

be2net: add code to display default value of tx rate for VFs

This change will allow the default value of tx rate to be displayed
when ip link show is called on a PF interface.

Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

be2net: pass domain id to be_cmd_link_status_query

Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

be2net: fix be_mcc_compl_process to identify eth_get_stat command

eth_get_statistics and vlan_config command have same opcode.
Use opcode subsystem id to differentiate one from other.

Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

be2net: Add code to display nic speeds other than 1Gbps/10Gbps

Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

be2net: allow register dump only for PFs

Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net:bna: fix compile warning of ‘bfa_ioc_smem_pgoff’ defined but not used

Fix the below compile warning:

drivers/net/bna/bfa_ioc.c:1922: warning: ‘bfa_ioc_smem_pgoff’ defined but not used

Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: forcedeth: fix compile warning of not used nv_set_tso function

Fix the below compile warning:
drivers/net/forcedeth.c:4266: warning: ‘nv_set_tso’ defined but not used

commit 569e146 converts forcedeth driver to use hw_features.
So, implement function of .set_tso is abandoned.

Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mac80211: explain padding in place of rate field

Apparently this was confusing still ... add a
note that the byte is needed as padding.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Implement get_antenna and set_antenna callback functions

Implement the get_antenna and set_antenna callback functions, which will
allow clients to control the antenna for all non-11n hardware (Antenna handling
in rt2800 is still a bit magical, so we can't use the set_antenna for those drivers
yet).

To best support the set_antenna callback some modifications are needed in the
diversity handling. We should never look at the default antenna settings to determine
if software diversity is enabled. Instead we should set the diversity flag when
possible, which will allow the link_tuner to automatically pick up the tuning.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Implement get_ringparam callback function

With the get_ringparam callback function we can export ring parameters
to ethtool through the mac80211 interface.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Optimize register access in rt2800usb

All register reads/writes in rt2800usb were previously done with
rt2800_register_read/rt2800_register_write. These however indirectly
call rt2x00usb_register_read/rt2x00usb_register_write which adds an
additional overhead of at least one call and several move instructions
to each register access.

Replacing the calls to rt2800_register_read/rt2800_register_write with
direct calls to rt2x00usb_register_read/rt2x00usb_register_write gets
rid of quite a number of instructions in the drivers hotpaths (IRQ
handling and txdone handling).

For consistency replace all references to rt2800_register_read/write
with the rt2x00usb_register_read/write variants.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Optimize register access in rt2800pci

All register reads/writes in rt2800pci were previously done with
rt2800_register_read/rt2800_register_write. These however indirectly
call rt2x00pci_register_read/rt2x00pci_register_write which adds an
additional overhead of at least one call and several move instructions
to each register access.

Replacing the calls to rt2800_register_read/rt2800_register_write with
direct calls to rt2x00pci_register_read/rt2x00pci_register_write gets
rid of quite a number of instructions in the drivers hotpaths (IRQ
handling and txdone handling).

For consistency replace all references to rt2800_register_read/write
with the rt2x00pci_register_read/write variants.

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Merge rt2x00ht.c contents in other files.

The two functions that are in rt2x00ht.c can be much better placed
closer to the places where the call-sites of these functions are (one
in rt2x00config.c and one in rt2x00queue.c) allowing us to make these
functions static.
Also, conditional compilations doesn't seem to be necessary anymore as
802.11n support is quite common nowadays.

This makes the code a bit easier readable and searchable.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Enable support for RT53xx PCI devices by default.

Code seems to be feature-complete, so no reason to not enable
these devices by default.

Also, remove the sentence about the support for these devices being
non-functional.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: RT33xx device support is no longer experimental.

The rt33xx devices support for both PCI and USB devices has been in
the tree for a couple of months now, and seems to be functional and
not in a worse shape than the support for rt28xx and rt30xx devices.

No longer mark it as experimental and enable the support for these
devices by default.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Add USB IDs.

Add USB IDs that are listed in the latest Ralink Windows and/or Linux drivers.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Allow dynamic addition of PCI/USB IDs.

Both USB and PCI drivers allow a system administrator to dynamically add
USB/PCI IDs to the device table that a driver supports via the
/sys/bus/{usb,pci,pci_express}/drivers/<driver-name>/new_id files.

However, for the rt2x00 drivers using this method currently crashes the
system with a NULL pointer failure.

This is due to the set-up of rt2x00 where the probe functions require a
rt2x00_ops structure in the driver_info field of the probed device. As
this field is empty for the dynamically added devices this fails for
these devices.

Fix this by introducing driver-specific probe wrappers that do nothing
but calling the bus-specific probe functions with the rt2x00_ops structure
as an argument, rather than depending on the driver_info field.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Linksys WUSB600N rev2 is a RT3572 device.

Move the USB ID entry from the unknown devices to the list of RT35xx based
devices.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Always inline rt2x00pci_enable_interrupt

This allows the compiler to perform the necessary bitfield calculations
during compile time instead of run time and thus reduces the number of
instructions to run during each tasklet invocation. This should improve
performance in the RX hotpath.

This comes at the cost of a slight increase in the module size (for
example rt2800pci):

Before:
   text    data     bss     dec     hex filename
  14133     832       4   14969    3a79 drivers/net/wireless/rt2x00/rt2800pci.ko

After:
   text    data     bss     dec     hex filename
  14149     832       4   14985    3a89 drivers/net/wireless/rt2x00/rt2800pci.ko

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Decrease association time for USB devices

When powersaving is enabled, assocaition times are very high
(for WPA2 networks, the time can easily be around the 3 seconds).

This is caused, because the flushing of the queues takes
too much time. Without the flushing callback mac80211 assumes
a timeout of 100ms while scanning. Limit all flush waiting
loops to the same maximum.

We can apply this maximum by passing the drop status to the
driver, which makes sure the driver performs extra actions
during the waiting for the queue to become empty.

After these changes, association times fall within the
healthy range of ~0.6 seconds with powersaving enabled.
The difference between association time between powersaving
enabled and disabled is now only ~0.1 second (which can also
be due to the measuring method).

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2800usb: add timer to handle TX_STA_FIFO

TX status is reported by the hardware when a packet has been
sent (or after TX failed after possible retries), which is some
time after the DMA completion.  Since the rt2800usb hardware can
not signal interrupts we have to use a timer, otherwise the
TX status would only be read by the next packet's TX DMA
completion, or by the watchdog thread.

Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2800usb: handle TX status timeouts

The watchdog just triggers rt2800usb_work_txdone() when it
detects a TX status timeout, thus rt2800usb_work_txdone() needs to
handle this case.

Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: fix queue timeout checks

Add a timestamp to each queue entry which is updated whenever
the status of the entry changes, and remove the per-queue
timestamps.  The previous check was incorrect and caused both
false positives and false negatives.

With the corrected check it comes apparent that the TX status
usually times out on rt2800usb unless there is sufficient traffic
(i.e. the next TX will complete the previous TX status).

Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2800usb: read TX_STA_FIFO asynchronously

Trying to fix the "TX status report missed" warnings
by reading the TX_STA_FIFO entries as quickly as possible.
The TX_STA_FIFO is too small in hardware, thus reading
it only from the workqueue is too slow and entries get lost.

Start an asynchronous read of the TX_STA_FIFO directly from
the TX URB completion callback (atomic context, thus it cannot
use the blocking rt2800_register_read()). If the async
read returns a valid FIFO entry, it is pushed into a larger
FIFO inside struct rt2x00_dev, until rt2800_txdone() picks
it up.

A .tx_dma_done callback is added to struct rt2x00lib_ops
to trigger the async read from the URB completion callback.

Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Use TXOP_HTTXOP for beacons

Use TXOP_HTTXOP for beacons to stay in sync with the legacy drivers.

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Update TX_SW_CFG2 init value

Bring the TX_SW_CFG2 initialisation for rt305x devices in sync with the
ralink legacy drivers.

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Use correct TBTT_SYNC config in AP mode

This seems to fix problems with some powersaving clients since a
positive value in TBTT_SYNC_CFG_TBTT_ADJUST introduces beacon skew,
which is not wanted in AP mode.

Also update the rest of the TBTT_SYNC config according to the
legacy drivers in AP mode.

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Make rt2x00_queue_entry_for_each more flexible

Allow passing a void pointer to rt2x00_queue_entry_for_each which in
turn in provided to the callback function.

Furthermore, allow the callback function to stop processing by returning
true. And also notify the caller of rt2x00_queue_entry_for_each if the
loop was canceled by the callback.

No functional changes, just preparation for an upcoming patch.

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Split rt2x00dev->flags

The number of flags defined for the rt2x00dev->flags field,
has been growing over the years. Currently we are approaching
the maximum number of bits which are available in the field.

A secondary problem, is that one part of the field are initialized only
during boot, because the driver requirements are initialized or device
requirements are loaded from the EEPROM. In both cases, the flags are
fixed and will not change during device operation. The other flags are
the device state, and will change frequently. So far this resulted in the fact
that for some flags, the atomic bit accessors are used, while for the others
the non-atomic variants are used.

By splitting the flags up into a "flags" and "cap_flags" we can put all flags
which are fixed inside "cap_flags". This field can then be read non-atomically.
In the "flags" field we keep the device state, which is going to be read atomically.

This adds more room for more flags in the future, and sanitizes the field access methods.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Fix stuck queue in tx failure case

Since commit 0b7fde54f94979edc67bbf86b5adba702ebfefe8 "rt2x00: Protect
queue control with mutex" rt2x00 used rt2x00queue_pause_queue for
stopping a tx queue in mac80211. But in case of a failure in the tx
path rt2x00 still called ieee80211_stop_queue which stopped the queue
but prevented rt2x00queue_unpause_queue to wake the queue up again
resulting in a stuck tx queue.

Fix this by also using rt2x00queue_pause_queue in case of tx failures.

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Enable WLAN LED on Ralink SoC (rt305x) devices

This patch adds WLAN LED support to the mac80211 rt2x00 driver for
Ralink SoC (rt305x) devices.  The current WLAN LED drivers in
rt2800lib.c set the LED brightness via an MCU request, but do nothing
for SoC.  This patch checks for SoC and sets the register to enable the
WLAN LED (instead of an MCU request).  This enables the WLAN LED for
RT305x devices.

Signed-off-by: Layne Edwards <ledwards@astrumtech.net>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: assign keycache slots to unencrypted stations

Frame filtering relies on having a valid destination index (keycache slot),
to keep track of the destination. Assigning a keycache slot (configured
to unencrypted, with no key data attached) improves powersave handling in
AP mode with no encryption.
The dummy keycache entry for a station is cleared, when a real key gets
added.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: fix powersave frame filtering/buffering in AP mode

This patch fixes a long standing issue of pending packets in the queue being
sent (and retransmitted many times) to sleeping stations.
This was made worse by aggregation through driver-internal retransmitting
of A-MDPU subframes.
Previously the hardware tx filter was cleared unconditionally for every
single packet - with this patch it uses the IEEE80211_TX_CTL_CLEAR_PS_FILT
for unaggregated frames.
A sta_notify driver op is added to stop aggregation for stations when they
enter powersave mode. Subframes stay buffered inside the driver, to ensure
that the BlockAck window keeps a sane state.
Since the driver uses software aggregation, the clearing of the tx filter
needs to be handled by the driver instead of mac80211 for aggregated frames.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Fix beacon generation on foreign channel

While leaving the oper channel, beacon generation is stopped
by mac80211 and beacon slots are marked as inactive.
During the scan, ath9k configures beacon timers
based on IEEE80211_CONF_OFFCHANNEL which inturn generates
beacon alert even though bslot is inactive.

ath9k fails to disable beacon alert while moving to offchannel
if none of the beacon slot is active. This is causing beacon
transmission on foreign channel. This patch enables swba
based on active bslots.

This issue was reported with two vifs (AP+STA) and triggered
scan in STA vif in unassociated state.

Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: add a function for setting the TIM bit for a specific station

This allows a driver to buffer frames for a PS station and tell mac80211
to wake it up even though mac80211 does not have any buffered frames for
it.
This is necessary for properly handling aggregation related buffering,
in ath9k, because the driver needs to keep its frames in order to keep
track of the Block-ACK window.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_htc: Fix free slot value for cab queue

ath9k_htc_tx_get_slot can return zero as valid index.

Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Acked-by: Sujith Manoharan <Sujith.Manoharan@Atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: optimize driver initialization code

1) removal of unnecessary mwifiex_device structure
2) avoid passing adapter pointer to mwifiex_init_sw()
3) remove local variable drv_mode_info in mwifiex_add_card()
4) type change in mwifiex_bss_attr to match mwifiex_private
5) removal of more wordy comments

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: remove some macro definitions

use corresponding macros defined in include/linux/ieee80211.h

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: remove redundant local variables and comments

Remove some local variables (mainly function return values)
that are used only once. Also, one dummy function and some
wordy comments are removed.

Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: fix debugfs printk format warning

Fix printf() format warning (tm_year is long int):

net/mac80211/debugfs_sta.c:113: warning: format '%d' expects type 'int', but argument 4 has type 'long int'

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlegacy: use pci_dev->revision

Commit be663ab67077fac8e23eb8e231a8c1c94cb32e54 (iwlwifi: split the drivers for
agn and legacy devices 3945/4965) added code to read the 4965's revision ID from
the PCI configuration register while it's already stored by PCI subsystem in the
'revision' field of 'struct pci_dev'...

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_htc: Cleanup HTC debugfs

Move the ath9k_htc debugfs under ieee80211 to be inline
with ath9k driver and it also helps to simplify debug code.

Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Acked-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_htc: Add debugfs support to change debug mask

Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Acked-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath: fix 0x6C for beaconing/passive scan flags based on country IE

The 0x6C regulatory domain is just like the 0x6A regulatory
domain but differs in that 0x6C will allow adhoc and active
scan on its channels only if we are associated to an AP
with a country IE that allows those channels. The
ath_reg_apply_beaconing_flags() does just this -- we respect
the manufacturer's intent on only enabling beaconing modes
of operation if and only if blessed by the country IE.

Cc: David Quan <david.quan@atheros.com>
Cc: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rfkill: Regulator consumer driver for rfkill

Add a regulator consumer driver for rfkill to enable controlling radio
transmitters connected to voltage regulators using the regulator
framework.

A new "vrfkill" virtual supply is provided to use in platform code.

Signed-off-by: Guiming Zhuo <gmzhuo@gmail.com>
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'master' of git://git./linux/kernel/git/padovan/bluetooth-next-2.6

Merge branch 'wireless-next-2.6' of git://git./linux/kernel/git/iwlwifi/iwlwifi-2.6

Merge branch 'master' of git://git./linux/kernel/git/kaber/nf-next-2.6

Merge branch 'master' of /linux/kernel/git/davem/net-2.6

Conflicts:
drivers/net/bnx2x/bnx2x_ethtool.c

net: qlge: convert to hw_features

Another simple conversion.

Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: vmxnet3: convert to hw_features

This also removes private feature flags that were always set to true.

You may want to move vmxnet3_set_features() to vmxnet3_drv.c as a following
cleanup.

Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: vxge: convert to hw_features

Side effect: ->gro_enable is removed as napi_gro_receive() does the
fallback itself.

Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: chelsio: convert to hw_features

Also remove flags that were not used or are now redundant to hw_features bits.
No device had UDP_CSUM_CAPABLE set.

Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: s2io: convert to hw_features

This removes advertising HW_CSUM as driver does not support it.

Note: driver advertises TSO6 but not IPV6_CSUM - bug maybe?

Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fix section mismatches

Fix build warnings like the following:

WARNING: drivers/net/built-in.o(.data+0x12434): Section mismatch in reference from the variable madgemc_driver to the variable .init.data:madgemc_adapter_ids

And add some consts to EISA device ID tables along the way.

Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

r8169: TSO fixes.

- the MSS value is actually contained in a 11 bits wide (0x7ff) field.
  The extra bit in the former MSSMask did encompass the TSO command
  bit ("LargeSend") as well (0xfff). Oops.

- the Tx descriptor layout is not the same through the whole chipset
  family. The 8169 documentation, the 8168c documentation and Realtek's
  drivers (8.020.00, 1.019.00, 6.014.00) highlight two layouts:
  1. 8169, 8168 up to 8168b (included) and 8101
  2. {8102e, 8168c} and beyond

- notwithstanding the "first descriptor" and "last descriptor" bits, the
  same Tx descriptor content is enforced when a packet consists of several
  descriptors. The chipsets are documented to require it.

Credits go to David Dillow <dave@thedillows.org> for the original patch.

Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Realtek <nic_swsd@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>