Mike Frysinger [Sat, 4 Apr 2009 12:09:24 +0000 (08:09 -0400)]
Blackfin: add workaround for anomaly
05000171
DESCRIPTION:
The Boot ROM is executed at power up/reset and changes the value of the
SICA_IWR registers from their default reset value of 0xFFFF, but does not
restore them.
WORKAROUND:
User code should not rely on the default value of these registers. Set
the desired values explicitly.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Sat, 4 Apr 2009 12:22:36 +0000 (08:22 -0400)]
Blackfin: update anomaly sheets
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Graf Yang [Sat, 4 Apr 2009 11:45:57 +0000 (07:45 -0400)]
Blackfin: nand: flush peripheral before polling it
We need to make sure the data written to the nand flash controller makes
it there before we start polling its status register. Otherwise, we may
get stale data and return before the controller is actually ready.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Scott Wood <scottwood@freescale.com>
Todor I Mollov [Sat, 4 Apr 2009 10:53:06 +0000 (06:53 -0400)]
Blackfin: spi: make cs deassert function deterministic
Blackfin SPI driver was not driving the SPI chip-select high before
putting the chip-select signals into tri-state mode. This is probably
something that slipped by unnoticed in most designs. If the signals are
put directly into a tri-state mode, then the board is relying on the
pull-up resistors to pull up the chip-select before the next transaction.
Most of the time this is fine, except when you have two transactions that
follow each other very closely, such as the flash erase and read status
register commands. In this case I was seeing a 500ns separation between
the transactions. In my setup, with a 10kOhm pull-up, it would meet
timing spec about half the time and resulted in intermittent errors. (A
stronger pull up would fix this, but our design is targeted for low power
consumption and a 3.3kOhm @ 3.3v is 3.3mW of needless power consumption.)
I modified the spi_cs_deactivate() function in bfin_spi.c to drive the
chip-selects high before putting them into tri-state. For me, this
resulted in a rise time of 5ns instead of the previous rise time of about
1us, and fully satisfied the timing spec of the chip.
Signed-off-by: Todor I Mollov <tmollov@ucsd.edu>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Wolfgang Denk [Sun, 5 Apr 2009 21:04:30 +0000 (23:04 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-arm
Jean-Christophe PLAGNIOL-VILLARD [Sat, 13 Dec 2008 20:08:05 +0000 (21:08 +0100)]
integratorap: fix PCI support
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Dirk Behme [Mon, 30 Mar 2009 19:15:23 +0000 (21:15 +0200)]
OMAP3: Update Overo pin mux for new expansion board
A new Overo expansion board uses GPIO 14, 21, 22 and 23 for LED's and
switches. This patch changes the pinmux configuration for those pins.
They were previously set up for unused MMC3_DAT4-7.
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
Jean-Christophe PLAGNIOL-VILLARD [Sun, 5 Apr 2009 11:08:03 +0000 (13:08 +0200)]
arm: unify reset command
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Sun, 5 Apr 2009 11:06:31 +0000 (13:06 +0200)]
arm: clean cache management
unify arm cache management except for non standard cache as ARM7TDMI
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Sun, 5 Apr 2009 11:02:43 +0000 (13:02 +0200)]
arm: update co-processor 15 access
import system.h from linux
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Guennadi Liakhovetski [Sat, 4 Apr 2009 22:42:02 +0000 (00:42 +0200)]
ARM: add the imx31_phycore_eet target to MAINTAINERS
imx31_phycore_eet is a variant of the imx31_phycore board with a few
extensions, which justifies a separate entry in the MAINTAINERS list,
whereas normally all entries sharing a single configuration file and a
board/ directory have only one entry in MAINTAINERS.
Reported-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Guennadi Liakhovetski [Sat, 4 Apr 2009 22:37:07 +0000 (00:37 +0200)]
ARM: fix out-of-tree build of imx31_phycore_eet
Fix out-of-tree build of the imx31_phycore_eet target.
Reported-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Jon Smirl [Sat, 4 Apr 2009 21:44:51 +0000 (17:44 -0400)]
mpc5200: reduce delays in i2c
The previous code waited 1000us before checking i2c
status. Measurement shows i2c is usually ready in
under 50us. Change the polling interval to 15us,
loop 6,667 times to keep the polling timeout constant
at 100ms.
Sanjeev Premi [Fri, 3 Apr 2009 08:30:07 +0000 (14:00 +0530)]
OMAP: Fix compile issue
Fixes this compile error:
board.c: In function 'do_switch_ecc':
board.c:339: error: 'cmd_tbl_t' has no member named 'help'
make[1]: *** [board.o] Error 1
make[1]: Leaving directory `/db/psp_git/users/
a0756819/u-boot/cpu/arm_cortexa8/omap3'
make: *** [cpu/arm_cortexa8/omap3/libomap3.a] Error 2
This is due to the fact that current command uses long
help for the usage print even if the CONFIG_SYS_LONGHELP
is not enabled. (Thanks Jean-Christophe for explanation).
Signed-off-by: Sanjeev Premi <premi@ti.com>
Minkyu Kang [Fri, 3 Apr 2009 00:56:16 +0000 (09:56 +0900)]
s3c64xx: fix the wrong gpio offset
This patch fix the wrong gpio offset
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Kyungmin Park [Wed, 26 Nov 2008 01:18:13 +0000 (10:18 +0900)]
Move machine specific code to board at s3c64xx (v2)
Move machine specific code to smdk6400.
Some board use OneNAND instead of NAND.
Some register MP0_CS_CFG[5:0] are controled by both h/w and s/w.
So it's better to use macro instead of hard-coded value.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Tom Rix [Thu, 2 Apr 2009 03:02:19 +0000 (22:02 -0500)]
ZOOM1 Remove legacy NAND defines
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Tom Rix [Thu, 2 Apr 2009 03:02:20 +0000 (22:02 -0500)]
OMAP3 Fix multiline formatting in board init files.
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Wolfgang Denk [Sat, 4 Apr 2009 22:27:57 +0000 (00:27 +0200)]
Update CHANGELOG, coding style cleanup.
Wolfgang Denk [Sat, 4 Apr 2009 22:18:44 +0000 (00:18 +0200)]
One more fix for building env_embedded.o
In addition to the changes for CONFIG_ENV_IS_IN_FLASH as done in
commit
afcbce07, we also need to do the same for
CONFIG_ENV_IS_IN_EEPROM and CONFIG_ENV_IS_IN_NVRAM.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Scott Wood [Thu, 2 Apr 2009 21:15:10 +0000 (16:15 -0500)]
common/image.c: Relocate strings in tables.
Without this, u-boot can crash or print garbage if the original link
address no longer points to a valid string.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Scott Wood [Thu, 2 Apr 2009 21:10:36 +0000 (16:10 -0500)]
mpc8260: Fill in brg's clock-frequency in device tree.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Scott Wood [Thu, 2 Apr 2009 23:20:43 +0000 (18:20 -0500)]
MPC8260ADS: Add nfsboot/ramboot to default environment.
This brings it in line with other Freescale boards.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Andreas Huber [Thu, 2 Apr 2009 15:15:34 +0000 (17:15 +0200)]
UBI/cfi-mtd: Fix mtd name for multiple chips
On platforms with multiple NOR chips, currently only the first one
can be selected using the "ubi part" command. This patch fixes this
problem by using different names for the NOR "mtd devices".
It also changes the name of the NOR MTD device from "cfi-mtd" to
"norX" (X indexing the device numer) to better match the mtdparts
defaults.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Andreas Huber <andreas.huber@keymile.com>
Peter Korsgaard [Tue, 31 Mar 2009 15:52:16 +0000 (17:52 +0200)]
tools/setlocalversion: use git svn instead of git-svn
Use the new "git <subcmd>" syntax instead of the deprecated
"git-<subcmd>".
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Mingkai Hu [Tue, 31 Mar 2009 06:09:40 +0000 (14:09 +0800)]
eSPI: add the eSPI register support
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Minkyu Kang [Mon, 30 Mar 2009 05:55:51 +0000 (14:55 +0900)]
cmd_mmc: add support for device command for selecting mmc device
This patch improves device command for selecting mmc device
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Alan Carvalho de Assis [Sat, 28 Mar 2009 22:50:16 +0000 (19:50 -0300)]
Small fix to m5282evb
This is just a small fix to get u-boot on m5282evb.
Signed-off-by: Alan Carvalho de Assis <acassis@gmail.com>
Artem Bityutskiy [Fri, 27 Mar 2009 09:21:14 +0000 (10:21 +0100)]
UBIFS: add R/O compatibility
Now UBIFS is supported by u-boot. If we ever decide to change the
media format, then people will have to upgrade their u-boots to
mount new format images. However, very often it is possible to
preserve R/O forward-compatibility, even though the write
forward-compatibility is not preserved.
This patch introduces a new super-block field which stores the
R/O compatibility version.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Acked-by: Adrian Hunter <Adrian.Hunter@nokia.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Mike Frysinger [Tue, 24 Mar 2009 02:27:34 +0000 (22:27 -0400)]
more command usage cleanup
Fix up a few dangling commands like in "Command usage cleanup" commit.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Ladislav Michl [Mon, 23 Mar 2009 11:06:07 +0000 (12:06 +0100)]
Separate mtdparts command from jffs2
On Thu, Mar 19, 2009 at 01:30:36PM +0100, Stefan Roese wrote:
> Currently the mtdparts commands are included in the jffs2 command support.
> This doesn't make sense anymore since other commands (e.g. UBI) use this
> infrastructure as well now. This patch separates the mtdparts commands from
> the jffs2 commands making it possible to only select mtdparts when no JFFS2
> support is needed.
... and to make it useful for NAND chips as well, we should also remove now
unrelated CONFIG_JFFS2_NAND. Note that struct part_info etc is in
jffs2/load_kernel.h which is a bit misleading filename for that purpose,
but that can be fixed later (tm).
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Mike Frysinger [Mon, 23 Mar 2009 02:18:01 +0000 (22:18 -0400)]
smc91111_eeprom: move board-specific init into SMC91111_EEPROM_INIT()
Rather than sticking Blackfin-specific stuff into the eeprom example, use
an indirect macro so that any board can override it with their own magic
sauce in their board config file.
Also fix some spurious semi-colons in defines while I'm at it ...
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Ben Warren <biggerbadderben@gmail.com>
Sascha Hauer [Sat, 21 Mar 2009 13:38:46 +0000 (09:38 -0400)]
mpc52xx phy: initialize only when needed
Do not initialize phy on startup, instead initialize it
when we actually need it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Wolfgang Denk [Sat, 4 Apr 2009 20:15:46 +0000 (22:15 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-at91
Jean-Christophe PLAGNIOL-VILLARD [Mon, 30 Mar 2009 14:51:40 +0000 (16:51 +0200)]
at91sam9263ek: enable hush and auto complete support
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Stelian Pop <stelian@popies.net>
Jean-Christophe PLAGNIOL-VILLARD [Fri, 27 Mar 2009 22:26:44 +0000 (23:26 +0100)]
at91: move dataflash spi driver to drivers/spi
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Fri, 27 Mar 2009 22:26:44 +0000 (23:26 +0100)]
at91: move usb driver to drivers/usb
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Fri, 27 Mar 2009 22:26:43 +0000 (23:26 +0100)]
at91rm9200: Reset update
Update the rm9200 reset sequence to try executing a board-specific reset
function and move specific board reset to board.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Fri, 27 Mar 2009 22:26:43 +0000 (23:26 +0100)]
at91rm9200: move serial shutdown code to serial drivers
introduce serial_exit for this purpose. Use it only when the rm9200
serial driver is active
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Fri, 27 Mar 2009 22:26:43 +0000 (23:26 +0100)]
at91rm9200: move serial driver to drivers/serial
add CONFIG_AT91RM9200_USART to activate the driver
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Ulf Samuelsson [Fri, 27 Mar 2009 22:26:43 +0000 (23:26 +0100)]
Add support for the AT91RM9200EK Board.
The AT91RM9200-EK Evaluation Board supports the AT91RM9200
ARM9-based 32-bit RISC microcontroller and enables real-time code development
and evaluation.
Here is the chip page on Atmel website:
http://www.atmel.com/dyn/products/tools_card.asp?tool_id=3507
with
- NOR (cfi driver)
- DataFlash
- USB OHCI
- Net
- I2C (hard)
Signed-off-by: Ulf Samuelsson <ulf@atmel.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Fri, 27 Mar 2009 22:26:42 +0000 (23:26 +0100)]
add dataflash mmc mux missing support
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Fri, 27 Mar 2009 22:26:42 +0000 (23:26 +0100)]
at91rm9200dk: Move conditional compilation to Makefile
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Fri, 27 Mar 2009 22:26:42 +0000 (23:26 +0100)]
at91: rename DATAFLASH_MMC_SELECT to CONFIG_DATAFLASH_MMC_SELECT
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Fri, 27 Mar 2009 22:26:42 +0000 (23:26 +0100)]
at91sam9: add watchdog support
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Fri, 27 Mar 2009 12:14:52 +0000 (13:14 +0100)]
at91sam9/at91cap: spi init add hardware chip select support
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Sat, 4 Apr 2009 17:15:40 +0000 (19:15 +0200)]
netstar: fix crc32.c dependancy location
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Wolfgang Denk [Sat, 4 Apr 2009 18:05:18 +0000 (20:05 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx
Scott Wood [Fri, 3 Apr 2009 20:24:40 +0000 (15:24 -0500)]
MPC8260ADS: Define CONFIG_HAS_ETH0.
This is required so that the MAC address will be updated in the device tree.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Scott Wood [Fri, 3 Apr 2009 20:26:45 +0000 (15:26 -0500)]
PQ2FADS: Enable PCI.
PCI on PQ2FADS is very similar to PCI on MPC8272ADS.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Wolfgang Denk [Sat, 4 Apr 2009 14:57:50 +0000 (16:57 +0200)]
Fix quoting bug introduced by commit
74de7aef
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Sat, 4 Apr 2009 14:14:51 +0000 (16:14 +0200)]
Fix implicit declaration of function 'htons'
Include <netinet/in.h> instead of <linux/in.h> to get htons()
prototpye.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Kumar Gala [Sat, 4 Apr 2009 15:21:02 +0000 (10:21 -0500)]
fsl_law: Fix bug in calculation of LAW sizing
In set_ddr_laws() when we determined how much of the size requested
to be mapped was covered by the the first LAW we needed to recalculate
the size based on what was actually mapped.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Thu, 2 Apr 2009 18:57:05 +0000 (13:57 -0500)]
fsl_pci: Move prototypes into fsl_pci.h and remove explicit externs
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Thu, 2 Apr 2009 18:22:48 +0000 (13:22 -0500)]
fsl_pci: Renamed immap_fsl_pci.h to fsl_pci.h
Rename the pci header for FSL HW so we can move some prototypes
in there and stop doing explicit externs
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Wolfgang Denk [Sat, 4 Apr 2009 14:10:40 +0000 (16:10 +0200)]
Fix building of env_embedded.o
Since commit
a706bfc7 common/env_embedded.o and tools/envcrc were
only built when CONFIG_ENV_IS_EMBEDDED was set, but this breaks
building for many boards.
We always have to build these files when CONFIG_ENV_IS_IN_FLASH is
set.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Jean-Christophe PLAGNIOL-VILLARD [Sat, 4 Apr 2009 10:49:11 +0000 (12:49 +0200)]
rename include/zlib.h to include/u-boot/zlib.h
Some systems have zlib.h installed in /usr/include/. This isn't the
desired file for u-boot code - we want the one in include/zlib.h.
This rename will avoid the conflict.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Jean-Christophe PLAGNIOL-VILLARD [Sat, 4 Apr 2009 10:46:31 +0000 (12:46 +0200)]
tools/Makefile: fix image.c dependancy location
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Sat, 4 Apr 2009 11:42:25 +0000 (07:42 -0400)]
tools: add ncb to gitignore
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Detlev Zundel [Fri, 3 Apr 2009 14:45:46 +0000 (16:45 +0200)]
include/ns16550.h: Unify structure declaration for registers
Instead of special casing the different access patterns, use common
code with light macros sprinkled in to accomodate for the different
layouts of the register structure.
Note that this also changes the types of the registers for the
"positively packed (>1)" cases. As the registers truly are unsigned
chars, this is surely the Right Thing, but it is a semantic change.
Note that for this case depending on the endianness on the bus, we may
see a change of behaviour.
Signed-off-by: Detlev Zundel <dzu@denx.de>
Peter Tyser [Fri, 13 Mar 2009 23:54:52 +0000 (18:54 -0500)]
Delete now unused tools/Makefile.win32
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Peter Tyser [Fri, 13 Mar 2009 23:54:51 +0000 (18:54 -0500)]
Add support for building native win32 tools
Add support for compiling the host tools in the tools directory using
the MinGW toolchain. This produces executables which can be used on
standard Windows computers without requiring cygwin.
One must specify the MinGW compiler and strip utilities as if they
were the host toolchain in order to build win32 executables, eg:
make HOSTCC=i586-mingw32msvc-gcc HOSTSTRIP=i586-mingw32msvc-strip tools
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Peter Tyser [Fri, 13 Mar 2009 23:54:50 +0000 (18:54 -0500)]
tools/Makefile: Simplify HOST_CFLAGS/HOST_LDFLAGS generation
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Peter Tyser [Fri, 13 Mar 2009 23:54:49 +0000 (18:54 -0500)]
tools/Makefile: Create generic build rules
Create a few generic build rules to replace the current method which has
1 build target for each file
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Peter Tyser [Fri, 13 Mar 2009 23:54:48 +0000 (18:54 -0500)]
tools/Makefile: Use auto-generated object file dependencies
Files in the SRCS variable have their dependencies automatically
generated so remove duplicate explicit dependencies
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Peter Tyser [Fri, 13 Mar 2009 23:54:47 +0000 (18:54 -0500)]
tools/Makefile: Remove symlinks for remaining source files
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Peter Tyser [Fri, 13 Mar 2009 23:54:46 +0000 (18:54 -0500)]
tools/Makefile: Dynamically generate libfdt object dependencies
Add the libfdt files to the SRCS variable so that they have their
dependencies automatically generated
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Peter Tyser [Fri, 13 Mar 2009 23:54:45 +0000 (18:54 -0500)]
tools/Makefile: Remove symlinks for fdt targets
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Peter Tyser [Fri, 13 Mar 2009 23:54:44 +0000 (18:54 -0500)]
tools/Makefile: Add libfdt/ to the include search path
This change makes the process of symlinking libfdt_internal.h
unnecessary
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Peter Tyser [Fri, 13 Mar 2009 23:54:43 +0000 (18:54 -0500)]
tools: Remove unecessary symlinking of zlib.h
crc32.c uses the zlib.h header in include/u-boot/zlib.h. The symlink
was previously necessary to give U-Boot's version of zlib.h precedence
over the host computer's version of zlib.h.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Peter Tyser [Fri, 13 Mar 2009 23:54:42 +0000 (18:54 -0500)]
tools/Makefile: Add tools/ to the include search path
This change makes the process of symlinking mkimage.h and fdt_host.h
unnecessary
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Peter Tyser [Fri, 13 Mar 2009 23:54:41 +0000 (18:54 -0500)]
tools/Makefile: Compile ncb when CONFIG_NETCONSOLE
Also conditionally add ncb.o to OBJ_FILES list
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Peter Tyser [Fri, 13 Mar 2009 23:54:40 +0000 (18:54 -0500)]
tools/Makefile: Make gen_eth_addr dependent upon CONFIG_CMD_NET
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Peter Tyser [Fri, 13 Mar 2009 23:54:39 +0000 (18:54 -0500)]
tools/Makefile: Make envcrc dependent upon CONFIG_ENV_IS_EMBEDDED
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Peter Tyser [Fri, 13 Mar 2009 23:54:38 +0000 (18:54 -0500)]
tools/Makefile: Make inca-swap-bytes dependent on CONFIG_INCA_IP
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Peter Tyser [Fri, 13 Mar 2009 23:54:37 +0000 (18:54 -0500)]
tools/Makefile: Make ubsha1 dependent upon CONFIG_SHA1_CHECK_UB_IMG
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Peter Tyser [Fri, 13 Mar 2009 23:54:36 +0000 (18:54 -0500)]
tools/Makefile: Make img2srec dependent upon CONFIG_CMD_LOADS
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Peter Tyser [Fri, 13 Mar 2009 23:54:35 +0000 (18:54 -0500)]
tools/Makefile: Build bmp_logo only when LCD or VIDEO logos are enabled
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Peter Tyser [Fri, 13 Mar 2009 23:54:34 +0000 (18:54 -0500)]
tools/Makefile: Split variable declarations into multiple lines
Split variable declarations into multiple lines and use the standard
VAR-y convention. Also move object and binary variable declarations to
after config.mk has been included to allow for these lists to utilize
the CONFIG_XXX variables.
These changes lay the groundwork for conditional compilation of files
in the tools directory.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Peter Tyser [Fri, 13 Mar 2009 23:54:33 +0000 (18:54 -0500)]
tools/Makefile: Remove inappropriate double-tabs
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Peter Tyser [Fri, 13 Mar 2009 23:54:32 +0000 (18:54 -0500)]
tools/Makefile: Remove HOSTARCH HOSTOS defines
The values of HOSTARCH and HOSTOS which are exported from the top-level
Makefile should be used
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Peter Tyser [Fri, 13 Mar 2009 23:54:31 +0000 (18:54 -0500)]
gen_eth_addr: Use POSIX rand() and srand()
Replace random()/srandom() use with rand()/srand() to support
compilation with the mingw toolchain. The rand()/srand() functions are
generally more common and are functionally equivalent to the original
random()/srandom() calls.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Peter Tyser [Fri, 13 Mar 2009 23:54:28 +0000 (18:54 -0500)]
elf.h: Use stdint.h to provide standard typedefs for WIN32
The original code provided an incomplete set of typedefs for WIN32
compiles and replicated the standard typedefs that are already
provided by stdint.h
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Peter Tyser [Fri, 13 Mar 2009 23:54:27 +0000 (18:54 -0500)]
common/Makefile: Conditionally compile env_embedded.o
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Peter Tyser [Fri, 13 Mar 2009 23:54:26 +0000 (18:54 -0500)]
Makefile: Add removal of *.exe files to clean target
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Peter Tyser [Fri, 13 Mar 2009 23:54:25 +0000 (18:54 -0500)]
Makefile: Make autoconf.mk a dependency of the depend target
The original code did not generate autoconf.mk until after some targets
dependencies had already been calculated, for example the directories in
the SUBDIRS variable
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
unsik Kim [Wed, 25 Feb 2009 02:31:24 +0000 (11:31 +0900)]
mflash: Initial mflash support
Mflash is fusion memory device mainly targeted consumer eletronic and
mobile phone.
Internally, it have nand flash and other hardware logics and supports
some different operation (ATA, IO, XIP) modes.
IO mode is custom mode for the host that doesn't have IDE interface.
(Many mobile targeted SoC doesn't have IDE bus)
This driver support mflash IO mode.
Followings are brief descriptions about IO mode.
1. IO mode based on ATA protocol and uses some custom command. (read
confirm, write confirm)
2. IO mode uses SRAM bus interface.
Signed-off-by: unsik Kim <donari75@gmail.com>
Wolfgang Denk [Fri, 3 Apr 2009 20:48:05 +0000 (22:48 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-nand-flash
Wolfgang Denk [Fri, 3 Apr 2009 20:42:44 +0000 (22:42 +0200)]
Merge branch 'sf' of git://git.denx.de/u-boot-blackfin
Wolfgang Denk [Fri, 3 Apr 2009 20:38:36 +0000 (22:38 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-blackfin
Wolfgang Denk [Fri, 3 Apr 2009 20:36:44 +0000 (22:36 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-fdt
Detlev Zundel [Fri, 3 Apr 2009 09:53:01 +0000 (11:53 +0200)]
Rename common ns16550 constants with UART_ prefix to prevent conflicts
Fix problems introduced in commit
7b5611cdd12ca0cc33f994f0d4a4454788fc3124 [inka4x0: Add hardware
diagnosis functions for inka4x0] which redefined MSR_RI which is
already used on PowerPC systems.
Also eliminate redundant definitions in ps2mult.h. More cleanup will
be needed for other redundant occurrences though.
Signed-off-by: Detlev Zundel <dzu@denx.de>
Scott Wood [Wed, 1 Apr 2009 20:33:24 +0000 (15:33 -0500)]
Noisily disable the legacy NAND subsystem.
Legacy NAND is marked for feature removal after April 2009 (i.e. this
upcoming release). There are still several boards that reference it
(though many do so only for disk-on-chip support which has been silently
disabled for a while now). These boards will now fail to build
with #error, though the code is still there if the user removes #error.
The plan is to remove the code outright in the next release, along with
any board code that refers to it (such as board/esd/common/auto_update.c).
Also, remove the legacy NAND API description from README.nand.
Signed-off-by: Scott Wood <scottwood@freescale.com>
apgmoorthy [Fri, 27 Mar 2009 09:15:23 +0000 (14:45 +0530)]
Fix OneNAND ipl to read CONFIG_SYS_MONITOR_LEN
Currently OneNAND initial program loader (ipl) reads only block 0 ie 128KB.
However, u-boot image for apollon board is 195KB making the board
unbootable with OneNAND.
Fix ipl to read CONFIG_SYS_MONITOR_LEN.
CONFIG_SYS_MONITOR_LEN macro holds the U-Boot image size.
Signed-off-by: Rohit Hagargundgi <h.rohit@samsung.com>
Signed-off-by: Gangheyamoorthy <moorthy.apg@samsung.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Wolfgang Denk [Wed, 1 Apr 2009 21:34:12 +0000 (23:34 +0200)]
Add "source" command; prepare removal of "autoscr" command
According to the doc/feature-removal-schedule.txt, the "autoscr"
command will be replaced by the "source" command in approximately 6
months from now.
This patch prepares this change and starts a 6 month transition
period as follows:
- The new "source" command has been added, which implements exactly
the same functionlaity as the old "autoscr" command before
- The old "autoscr" command name is kept as an alias for compatibility
- Command sequences, script files atc. have been adapted to use the
new "source" command
- Related environment variables ("autoscript", "autoscript_uname")
have *not* been adapted yet; these will be renamed resp. removed in
a separate patch when the support for the "autoscr" command get's
finally dropped.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Thu, 2 Apr 2009 15:31:09 +0000 (17:31 +0200)]
Add "GPL cleanup" task to feature-removal-schedule.txt
Announce removal of all non-GPL or GPL-incompatible files
after August 2009.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Mike Frysinger [Thu, 2 Apr 2009 16:51:28 +0000 (12:51 -0400)]
sf: stmicro: dont send 4 bytes when reading status register
I can't find anywhere in the datasheet that says the status register needs
3 dummy bytes sent to it before being able to read back the first real
result. Tests on a Blackfin board show that after writing the opcode, the
status register starts coming back immediately. So only write out the
read status register opcode before polling the result.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Jason McMullan <mcmullan@netapp.com>
CC: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Mike Frysinger [Thu, 2 Apr 2009 12:11:31 +0000 (08:11 -0400)]
sf: set common timeouts in seconds, not milliseconds
Since timeouts are only hit when there is a problem in the system, we
don't want to prematurely timeout on a functioning setup. Thus having
low timeouts (in milliseconds) doesn't gain us anything in the production
case, but rather increases likely hood of causing problems where none
otherwise exist.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Mike Frysinger [Thu, 2 Apr 2009 10:51:49 +0000 (06:51 -0400)]
sf: stmicro: use common page timeout define
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Mike Frysinger [Sat, 28 Mar 2009 10:41:09 +0000 (06:41 -0400)]
sf: always read 5 bytes for the idcode
Some SPI flash drivers like to have extended id information available
(like the spansion flash), so rather than making it re-issue the ID cmd
to get at the last 2 bytes, have the common code read 5 bytes rather than
just 3. This also matches the Linux behavior where it always reads 5 id
bytes from all flashes.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
CC: Mingkai Hu <Mingkai.hu@freescale.com>
projects / project / bcm63xx / u-boot.git / log