Kristjan Krušič [Sun, 19 Mar 2023 16:58:16 +0000 (17:58 +0100)]
ipq-wifi: bump to latest git HEAD
31ff96d ipq806x: add support for Nokia Airscale AC400i
1af1df2 ath11k: ipq8074: add Netgear WAX218
Signed-off-by: Kristjan Krušič <kristjan.krusic@krusic22.com>
Kristjan Krušič [Sat, 4 Feb 2023 16:00:57 +0000 (17:00 +0100)]
ipq806x: add support for Nokia Airscale AC400i
Hardware
--------
SoC: Qualcomm IPQ8065
RAM: 512 MB DDR3
Flash: 256 MB NAND (Macronix MX30UF2G18AC) (split into 2x128MB)
4 MB SPI-NOR (Macronix MX25U3235F)
WLAN: Qualcomm Atheros QCA9984 - 2.4Ghz
Qualcomm Atheros QCA9984 - 5Ghz
ETH: eth0 - POE (100Mbps in U-Boot, 1000Mbps in OpenWrt)
eth1 - (1000Mbps in both)
Auto-negotiation broken on both.
USB: USB 2.0
LED: 5G, 2.4G, ETH1, ETH2, CTRL, PWR (All support green and red)
BTN: Reset
Other: SD card slot (non-functional)
Serial: 115200bps, near the Ethernet transformers, labeled 9X.
Connections from the arrow to the 9X text:
[NC] - [TXD] - [GND] - [RXD] - [NC]
Installation
------------
0. Connect to the device
Plug your computer into LAN2 (1000Mbps connection required).
If you use the LAN1/POE port, set your computer to force a 100Mbps link.
Connect to the device via TTL (Serial) 115200n8.
Locate the header (or solder pads) labeled 9X,
near the Ethernet jacks/transformers.
There should be an arrow on the other side of the header marking.
The connections should go like this:
(from the arrow to the 9X text): NC - TXD - GND - RXD - NC
1. Prepare for installation
While the AP is powering up, interrupt the startup process.
MAKE SURE TO CHECK YOUR CURRENT PARTITION!
If you see: "Current Partition is : partB" or
"Need to switch partition from partA to partB",
you have to force the device into partA mode, before continuing.
This can be done by changing the PKRstCnt to 5 and resetting the device.
setenv PKRstCnt 5
saveenv
reset
After you interrupt the startup process again,
you should see: Need to switch partition from partB to partA
You can now continue to the next step.
If you see: "Current Partition is : partA",
you can continue to the next step.
2. Prevent partition switching.
To prevent the device from switching partitions,
we are going to modify the startup command.
set bootcmd "setenv PKRstCnt 0; saveenv; bootipq"
setenv
3. First boot
Now, we have to boot the OpenWrt intifs.
The easiest way to do this is by using Tiny PXE.
You can also use the normal U-Boot tftp method.
Run "bootp" this will get an IP from the DHCP server
and possibly the firmware image.
If it doesn't download the firmware image, run "tftpboot".
Now run "bootm" to run the image.
You might see:
"ERROR: new format image overwritten - must RESET the board to recover"
this means that the image you are trying to load is too big.
Use a smaller image for the initial boot.
4. Install OpenWrt from initfs
Once you are booted into OpenWrt,
transfer the OpenWrt upgrade image and
use sysupgrade to install OpenWrt to the device.
Signed-off-by: Kristjan Krušič <kristjan.krusic@krusic22.com>
Aleksander Jan Bajkowski [Sun, 12 Mar 2023 09:59:21 +0000 (10:59 +0100)]
lantiq: xway: add phy reset pin to AVM Fritz!Box 7320
This commit adds the PHY reset gpio for the LAN1 port to the dts.
According to the GPL sources, gpios 34 and 36 are used on the AVM
FritzBox 7320 and 7330. The second port is unsupported.
The gpio assignment has been verified on the FritzBox 7330.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Nick Hainke [Mon, 13 Mar 2023 22:24:24 +0000 (23:24 +0100)]
nftables: update to 1.0.7
Release Notes:
https://marc.info/?l=netfilter-devel&m=
167873533214563&w=2
Signed-off-by: Nick Hainke <vincent@systemli.org>
Nick Hainke [Fri, 10 Mar 2023 17:48:51 +0000 (18:48 +0100)]
libnftnl: update to 1.2.5
Upstream switched to "tar.xz".
Release Notes:
https://www.spinics.net/lists/netfilter/msg61016.html
Signed-off-by: Nick Hainke <vincent@systemli.org>
Christian Marangi [Sat, 18 Mar 2023 11:47:48 +0000 (12:47 +0100)]
ipq40xx: mf18a: rename wifi0 calibration variant to ZTE-MF18A
Rename wifi0 calibration variant to ZTE-MF18A to allign to BDF changes
for ZTE MF18A.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Christian Marangi [Sat, 18 Mar 2023 11:46:33 +0000 (12:46 +0100)]
ipq-wifi: bump to latest git HEAD
86180c4 ath10k-firmware: IPQ4019 hw1.0: Rename variant to ZTE MF18A specific BDF
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Christian Marangi [Sat, 18 Mar 2023 11:01:04 +0000 (12:01 +0100)]
ipq-wifi: bump to latest git HEAD
1f35a8c ath10k-firmware: IPQ4019 hw1.0: Add variant to Teltonika RUTX10 specific BDF
a49672f ath10k-firmware: QCA99X0 hw2.0: Add variant to ZTE MF18A specific BDF
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Christian Marangi [Sat, 18 Mar 2023 10:42:27 +0000 (11:42 +0100)]
ipq40xx: rutx10: Add missing variant to ath10k wifi
Add missing variant to ath10k wifi to allign to BDF changes for
Teltonika RUTX10.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Christian Marangi [Sat, 18 Mar 2023 10:08:26 +0000 (11:08 +0100)]
ipq40xx: mf18a: Add missing variant to PCI ath10k card
Add missing variant to PCI ath10k card to allign to BDF changes for
ZTE MF18A.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
John Audia [Mon, 13 Mar 2023 13:04:36 +0000 (09:04 -0400)]
kernel: bump 5.15 to 5.15.102
No patches needed to be rebased.
Signed-off-by: John Audia <therealgraysky@proton.me>
Tested-by: Robert Marko <robimarko@gmail.com> #ipq807x/Dynalink WRX36
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> #ipq807x/ax3600, x86_64/FW-7543B, ath79/tl-wdr3600, ipq806x/g10, ipq806x/nbg6817
John Audia [Sun, 12 Mar 2023 15:07:58 +0000 (11:07 -0400)]
kernel: bump 5.15 to 5.15.101
No patches rebased as a function of this bump.
Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3
Signed-off-by: John Audia <therealgraysky@proton.me>
John Audia [Sun, 12 Mar 2023 14:16:50 +0000 (10:16 -0400)]
kernel: bump 5.15 to 5.15.100
Manually rebased:
bcm27xx/patches-5.15/950-0421-Support-RPi-DPI-interface-in-mode6-for-18-bit-color.patch
bcm27xx/patches-5.15/950-0706-media-i2c-imx219-Scale-the-pixel-clock-rate-for-the-.patch
ramips/patches-5.15/810-uvc-add-iPassion-iP2970-support.patch
Removed upstreamed:
bcm27xx/patches-5.15/950-0707-drm-vc4-For-DPI-MEDIA_BUS_FMT_RGB565_1X16-is-mode-1-.patch[1]
bcm27xx/patches-5.15/950-0596-drm-vc4-dpi-Add-option-for-inverting-pixel-clock-and.patch[2]
ipq807x/0006-v5.16-arm64-dts-qcom-Fix-IPQ8074-PCIe-PHY-nodes.patch [3]
ipq807x/0034-v6.1-arm64-dts-qcom-ipq8074-fix-PCIe-PHY-serdes-size.patch [4]
ipq807x/0103-arm64-dts-qcom-ipq8074-fix-Gen2-PCIe-QMP-PHY.patch [5]
ipq807x/0104-arm64-dts-qcom-ipq8074-fix-Gen3-PCIe-QMP-PHY.patch [6]
ipq807x/0105-arm64-dts-qcom-ipq8074-correct-Gen2-PCIe-ranges.patch [7]
ipq807x/0108-arm64-dts-qcom-ipq8074-fix-Gen3-PCIe-node.patch [8]
ipq807x/0109-arm64-dts-qcom-ipq8074-correct-PCIe-QMP-PHY-output-c.patch [9]
ipq807x/0132-arm64-dts-qcom-ipq8074-correct-USB3-QMP-PHY-s-clock-.patch [10]
All other patches automatically rebased.
1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.99&id=
d2991e6b30020e286f2dd9d3b4f43548c547caa6
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/drivers/gpu/drm/vc4/vc4_dpi.c?h=v5.15.100&id=
8e04aaffb6de5f1ae61de7b671c1531172ccf429
3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/arch/arm64/boot/dts/qcom/ipq8074.dtsi?h=v5.15.99&id=
a55a645aa303a3f7ec37db69822d5420657626da
4. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/arch/arm64/boot/dts/qcom/ipq8074.dtsi?h=v5.15.99&id=
d9df682bcea57fa25f37bbf17eae56fa05662635
5. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/arch/arm64/boot/dts/qcom/ipq8074.dtsi?h=v5.15.99&id=
7e6eeb5fb3aa9e5feffdb6e137dcc06f5f6410e1
6. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/arch/arm64/boot/dts/qcom/ipq8074.dtsi?h=v5.15.99&id=
e88204931d9a60634cd50bbc679f045439c4b91d
7. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/arch/arm64/boot/dts/qcom/ipq8074.dtsi?h=v5.15.99&id=
1563af0f28afd3b6d64ac79a2aecced3969c90bf
8. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/arch/arm64/boot/dts/qcom/ipq8074.dtsi?h=v5.15.99&id=
feb8c71f015d416f1afe90e1f62cf51e47376c67
9. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/arch/arm64/boot/dts/qcom/ipq8074.dtsi?h=v5.15.99&id=
69c7a270357a7d50ffd3471b14c60250041200e3
10. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/arch/arm64/boot/dts/qcom/ipq8074.dtsi?h=v5.15.99&id=
dd3d021ae5471d98adf81f1e897431c8657d0a18
Build system: x86_64
Build-tested: bcm2711/RPi4B, ramips/tplink_archer-a6-v3
Run-tested: bcm2711/RPi4B, ramips/tplink_archer-a6-v3
Signed-off-by: John Audia <therealgraysky@proton.me>
Tested-by: Robert Marko <robimarko@gmail.com> #ipq807x/Dynalink WRX36
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> #ipq807x/ax3600, x86_64/FW-7543B, ath79/tl-wdr3600, ipq806x/g10, ipq806x/nbg6817
John Audia [Sat, 11 Mar 2023 15:42:26 +0000 (10:42 -0500)]
kernel: tcindex classifier has been retired
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/net/sched?h=v5.15.100&id=
7c183dc0af472dec33d2c0786a5e356baa8cad19
Signed-off-by: John Audia <therealgraysky@proton.me>
John Audia [Sat, 11 Mar 2023 15:28:02 +0000 (10:28 -0500)]
x86: set deprecated CONFIG_MICROCODE_OLD_INTERACE
We use late loading[1] so need to set this option despite upstream adding a
kernel taint when this option is set. See discussion in PR#12149 for more details.
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/diff/arch/x86/Kconfig?id=v5.15.100&id2=v5.15.98
1. https://github.com/openwrt/openwrt/blob/master/target/linux/x86/base-files/lib/preinit/02_load_x86_ucode
Signed-off-by: John Audia <therealgraysky@proton.me>
Eneas U de Queiroz [Sun, 19 Feb 2023 02:19:31 +0000 (23:19 -0300)]
uencrypt: split common and library-specific code
This splits the code in 4 files:
- uencrypt.h
- uencrypt.c - main program
- uencrypt-openssl.c - OpenSSL/wolfSSL implementation
- uencrypt-mbedtls - mbedTLS implementation
Other changes, accounting for ~400 bytes increase in ipk size:
- more error condition checking and reporting,
- hide key and iv command line arguments
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Eneas U de Queiroz [Fri, 17 Feb 2023 11:12:40 +0000 (08:12 -0300)]
uencrypt: add support for mbedtls
This commit includes some additional changes:
- better handling of iv and keys in openssl/wolfssl variants
- fix compiler warnings and whitespace
- build all 3 variants as separate packages
- adjust the new package name in targets' DEVICE_PACKAGES
- remove PKG_FLAGS:=nonshared
[Beeline SmartBox Flash - OK]
Tested-by: Mikhail Zhilkin <csharper2005@gmail.com>
[after test: replaced a hardcoded IV size of 16 by cipher_info->iv_size]
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Rafał Miłecki [Fri, 17 Mar 2023 15:36:08 +0000 (16:36 +0100)]
kernel: update v6.3 of patches
1. Use final (accepted) patches
2. Add two more required for v6.4 nvmem stuff
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Mantas Pucka [Wed, 15 Mar 2023 07:50:06 +0000 (09:50 +0200)]
ipq40xx: update Crisis Innovation Lab MeshPoint.One BDF
Make sure it uses updated Jalapeno BDF inherited from
Device/8dev_jalapeno-common
Fixes: 146eb4925c7f ("ipq40xx: add support for Crisis Innovation Lab MeshPoint.One")
Signed-off-by: Mantas Pucka <mantas@8devices.com>
[ fix Fixes tag to correct format and fix commit title ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Mantas Pucka [Fri, 17 Mar 2023 01:00:48 +0000 (02:00 +0100)]
ipq40xx: set specific BDF file for 8devices Habanero/Jalapeno
Set specific BDF file for 8devices Habanero/Jalapeno in ipq40xx
generic.mk
Signed-off-by: Mantas Pucka <mantas@8devices.com>
[ split ipq40xx changes in separate commit ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Mantas Pucka [Thu, 16 Mar 2023 14:30:13 +0000 (16:30 +0200)]
ipq-wifi: bump to latest git HEAD and add 8devices boards
2dae618 ipq-wifi: update 8devices Jalapeno BDF
08e92db ipq-wifi: update 8devices Habanero BDF
Signed-off-by: Mantas Pucka <mantas@8devices.com>
[ split ipq40xx changes in separate commit ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Paul Spooren [Wed, 22 Feb 2023 18:57:45 +0000 (19:57 +0100)]
layerscape: switch to Kernel 5.15 by default
Getting ready for the next release.
Tested-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Paul Spooren <mail@aparcar.org>
Christian Marangi [Tue, 14 Mar 2023 21:34:48 +0000 (22:34 +0100)]
rpcd: bump to latest git HEAD
d978830 rc: add option to get info for a single script in list method
632b4fc rc: add option to skip running check for list method
5577db9 rc: add support for scanning USE_PROCD and skip running if not supported
4de3f02 rc: fix and improve script scanning START and STOP
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Andre Heider [Sun, 5 Feb 2023 22:21:46 +0000 (23:21 +0100)]
toolchain/gcc: enable zstd support
LTO object files will now be compressed using zstd.
Compressing debug sections with zstd will have to wait for GCC 13,
which adds support for -gz=zstd.
NOTE: wiping the ccache is strongly recommended, not doing so might
yield build error later on:
"lto1: internal compiler error: original not compressed with zstd"
Signed-off-by: Andre Heider <a.heider@gmail.com>
Andre Heider [Sun, 5 Feb 2023 22:12:05 +0000 (23:12 +0100)]
toolchain/binutils: enable zstd support
Debug sections can now be compressed using zstd.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Rafał Miłecki [Thu, 16 Mar 2023 22:34:37 +0000 (23:34 +0100)]
bcm4908: add HVC workaround for booting kernel 5.15
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rafał Miłecki [Thu, 16 Mar 2023 21:01:51 +0000 (22:01 +0100)]
bcm4908: include usbport trigger
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rafał Miłecki [Thu, 16 Mar 2023 19:28:47 +0000 (20:28 +0100)]
bcm4908: backport v6.4 pending DTS changes
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Álvaro Fernández Rojas [Thu, 16 Mar 2023 18:38:31 +0000 (19:38 +0100)]
bmips: tweak Kconfig options
Add patch to reduce and improve selected bmips kernel config options.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Álvaro Fernández Rojas [Thu, 16 Mar 2023 18:20:23 +0000 (19:20 +0100)]
bmips: irq-bcm6345-l1: register memory region
Add new patch sent upstream for requesting the memory region in the bcm6345-l1
interrupt controller.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Álvaro Fernández Rojas [Thu, 16 Mar 2023 18:16:11 +0000 (19:16 +0100)]
bmips: update patches sent upstream
Update bmips patches with the latest version sent upstream
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Hauke Mehrtens [Wed, 15 Mar 2023 23:30:26 +0000 (00:30 +0100)]
include: autotools: Add dummy GTKDOCIZE
autoreconf wants to use the gtkdocize tool now if a configure.ac file
defines GTK_DOC_CHECk(). OpenWrt does not ship the gtkdocize tool, just
use true instead. This fixes the build of some applications like guntls.
Fixes: 030447b8f4c7 ("tools/autoconf: bump to 2.71")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Jo-Philipp Wich [Wed, 15 Mar 2023 23:31:16 +0000 (00:31 +0100)]
tools/autoconf: ensure relocatability
Upstream introduced a new `trailer.m4` macro file referenced by the
absolute build path of autoconf. Make sure that this is covered by
the `000-relocatable.patch` as well.
This should fix various SDK build failures related to autoconf.
Fixes: 030447b8f4 ("tools/autoconf: bump to 2.71")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Christian Marangi [Sat, 4 Mar 2023 10:38:32 +0000 (11:38 +0100)]
firmware: ipq-wifi: use project branch and drop local file
Source BDF files out of project dedicated repository and drop local file
from openwrt main repository.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
David Bauer [Tue, 14 Mar 2023 01:06:40 +0000 (02:06 +0100)]
ramips: add support for TP-Link Archer AX23 v1
Hardware
--------
CPU: MediaTek MT7621 DAT
RAM: 128MB DDR3 (integrated)
FLASH: 16MB SPI-NOR ()
WiFi: MediaTek MT7905 + MT7975 (2.4 / 5 DBDC) 802.11ax
SERIAL: 115200 8N1
LEDs - (3V3 - GND - RX - TX) - ETH ports
Installation
------------
Upload the factory image using the Web-UI.
Web-Recovery
------------
The router supports a HTTP recovery mode by holding the reset-button
when powering on. The interface is reachable at 192.168.0.1 and supports
installation using the factory image.
Signed-off-by: David Bauer <mail@david-bauer.net>
David Bauer [Tue, 14 Mar 2023 21:31:06 +0000 (22:31 +0100)]
firmware-utils: update to latest HEAD
a2c80c5 tplink-safeloader: add Archer AX23
3c04ecf tplink-safeloader: add Cloud image detection
87e593d tplink-safeloader: add QNEW image detection
34fbf48 tplink-safeloader: add vendor info support
d86cc1b tplink-safeloader: refactor image ingestion
5d3a14a tplink-safeloader: ignore NULLs in version info
71ddbcd tplink-safeloader: don't end-pad sysupgrade file
a29817e tplink-safeloader: stop at nameless partition
0c8a724 tplink-safeloader: replace hardcoded offsets
b82a521 tplink-safeloader: use enum for table types
201a6c0 tplink-safeloader: stricter free_image_partition()
Signed-off-by: David Bauer <mail@david-bauer.net>
Mark Mentovai [Fri, 11 Nov 2022 16:41:37 +0000 (11:41 -0500)]
odhcp6c: add "verbose" option
odhcp6c logs messages related to its activity when invoked with -v, but
there is no way to configure this from within OpenWrt. This adds a UCI
option to turn on odhcp6c logging, disabled by default. To enable, set,
for example, network.wan6.verbose = 1.
Signed-off-by: Mark Mentovai <mark@mentovai.com>
Paul Spooren [Sun, 12 Mar 2023 15:56:41 +0000 (16:56 +0100)]
imagebuilder: allow to specific ROOTFS_PARTSIZE
Setting this options modifies the rootfs size of created images. When
installing a large number of packages it may become necessary to
increase the size to have enough storage.
This option is only useful for supported devices, i.e. with an attached
SD Card or installed on a hard drive.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Paul Spooren [Wed, 22 Feb 2023 19:04:03 +0000 (20:04 +0100)]
realtek: switch to Kernel 5.15 by default
Getting ready for the next release.
Tested-by: Sander Vanheule <sander@svanheule.net>
Tested-by: Olliver Schinagl <oliver@schinagl.nl>
Tested-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Paul Spooren <mail@aparcar.org>
Rosen Penev [Thu, 31 Mar 2022 23:13:17 +0000 (16:13 -0700)]
tools/libtool: bump to 2.4.7
Remove upstreamed patch and refresh others.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
[rebased and refreshed patches again]
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Eneas U de Queiroz [Mon, 13 Sep 2021 21:08:55 +0000 (18:08 -0300)]
tools/libtool: bump to 2.4.6
This updates libtool to its current release, from 2015. Current patches
were renumbered and given a description text. The fix in
160-passthrough-ssp.patch is no longer needed.
A patch to speed up build was cherry-picked, and another openwrt
specific patch was needed to not use quotes in $(SHELL), to acommodate
our "SHELL=/usr/bin/env bash" usage.
The already present call to ./bootstrap ensures that generated files are
refreshed, so the patches are applied only to their sources. Also, that
bootstrap call was adjusted to run at the appropriate time when QUILT=1.
References below are relevant commits to upstream libtool
regarding some of the changes to patches.
This commit is being reapplied after previous revertion, and after some editing.
The fix for the issue that prompted reverting is the parent of this commit.
Ref:
435cb8d71 ("libtoolize: simplify runtime by substituting pkgauxdir")
Ref:
3cf11cfe2 ("libtoolize: rewritten over funclib.sh instead of general.m4sh")
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
[refactored to simplify patch changes, expanded patches, added upstream references]
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Sebastian Kemper [Fri, 24 Sep 2021 12:28:20 +0000 (14:28 +0200)]
tools/libtool: fix hard-coded paths
libtoolize hardcodes some paths. This is fine when building libtool and
then using it (for example in OpenWrt's buildroot). But when using an
SDK the paths are most likely different.
For example, when building util-linux within an SDK we're greeted with
the following message:
libtoolize: error: $pkgauxdir is not a directory: '/path/to/openwrt/staging_dir/host/share/libtool/build-aux'
This is because staging_dir/host/bin/libtoolize contains the following
hard-coded paths from when the SDK was built in the first place:
prefix="/path/to/openwrt/staging_dir/host"
datadir="/path/to/openwrt/staging_dir/host/share"
pkgauxdir="/path/to/openwrt/staging_dir/host/share/libtool/build-aux"
pkgltdldir="/path/to/openwrt/staging_dir/host/share/libtool"
aclocaldir="/path/to/openwrt/staging_dir/host/share/aclocal"
This commits updates 000-relocatable.patch to correct the paths,
relative to "$STAGING_DIR_HOST".
Ref:
96e05e2e3 ("libtool: Revert "libtool: bump to 2.4.6"")
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
[adapted to older libtool version before bumping, use STAGING_DIR_HOST]
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Michael Pratt [Thu, 9 Mar 2023 14:35:13 +0000 (09:35 -0500)]
tools/libtool: add commit messages to patches
Add commit messages to patches as intended
by the last bump to libtool which had to be reverted.
This allows for a cleaner diff later,
removing this clutter from the complex changes to patches
that are required to bump to the latest libtool version.
Ref:
c377d874b ("libtool: bump to 2.4.6")
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Michael Pratt [Thu, 9 Mar 2023 13:29:38 +0000 (08:29 -0500)]
tools/libtool: refresh patches
Preparation for bumping libtool several versions at once,
which includes some complex changes to patches.
Remove an empty line change from a patch.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Michael Pratt [Mon, 1 Aug 2022 12:30:43 +0000 (08:30 -0400)]
tools/automake: bump to 1.16.5
Automake releases 1.16.2 to 1.16.5 are major releases,
the two before are minor releases.
The first patch needed rewriting, some lines moved
to be consistent with the same change upstream in other files.
This also simplifies the patch.
Second patch refreshed.
Links to changelogs in order, oldest to newest.
Link: https://lists.gnu.org/archive/html/info-gnu/2018-02/msg00008.html
Link: https://lists.gnu.org/archive/html/info-gnu/2018-03/msg00002.html
Link: https://lists.gnu.org/archive/html/info-gnu/2020-03/msg00009.html
Link: https://lists.gnu.org/archive/html/info-gnu/2020-11/msg00005.html
Link: https://lists.gnu.org/archive/html/info-gnu/2021-07/msg00013.html
Link: https://lists.gnu.org/archive/html/info-gnu/2021-10/msg00000.html
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Michael Pratt [Mon, 1 Aug 2022 12:28:44 +0000 (08:28 -0400)]
tools/autoconf: bump to 2.71
Autoconf release 2.71 is a bugfix release of 2.70
Links provided are the changelog of 2.70 [1] [2]
and the announcement of 2.71 [3]
The first patch needed to be rewritten.
Some of the lines in the patch were moved
to be consistent with the same change added upstream
in other similar files.
Second and third patches are no longer needed,
Emacs can now be disabled at the configure stage,
and support for musl was added upstream.
The patch now causes help2man to be required
for installing man pages, but we don't need them.
There is no way to disable man pages build
with the configure script,
so use make to touch the files with the build target install-man1.
Link: https://lists.gnu.org/archive/html/autotools-announce/2020-12/msg00001.html
Link: https://lwn.net/Articles/839395
Link: https://lists.gnu.org/archive/html/info-gnu/2021-01/msg00017.html
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Michael Pratt [Mon, 1 Aug 2022 12:29:29 +0000 (08:29 -0400)]
tools/autoconf-archive: bump to 2022.09.03
Changelog included in package.
Link to announcement.
Link: https://lists.gnu.org/archive/html/info-gnu/2022-09/msg00004.html
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Michael Pratt [Fri, 2 Sep 2022 18:51:48 +0000 (14:51 -0400)]
tools/automake: use make variable to generate aclocal symlinks
Instead of having a somewhat random list of aclocal symlinks
which are named with the API versioning scheme,
install a symlink for every API version since 1.11
(the first release after Automake was moved to git)
using the API version number from the version of automake
that is currently in openwrt.
Automake API versioning does not include the patch level number.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Michael Pratt [Wed, 7 Sep 2022 14:45:43 +0000 (10:45 -0400)]
tools/automake: clean up build recipes
The configure option datarootdir
defaults to PREFIX/share.
The Host/Clean define should be Host/Uninstall
otherwise it is removing the build directory
before there is a chance to try "make uninstall"
in that directory.
Host/Clean/Default is no longer defined.
Consolidate the install stage with Host/Uninstall,
since it is essentially uninstalling before installing.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Michael Pratt [Wed, 7 Sep 2022 14:06:15 +0000 (10:06 -0400)]
tools/autoconf: clean up build recipes
The configure option datarootdir
defaults to PREFIX/share.
The Host/Clean define should be Host/Uninstall
otherwise it is removing the build directory
before there is a chance to try "make uninstall"
in that directory.
Host/Clean/Default is no longer defined.
Use default build recipes defined in host-build.mk
instead of custom ones that are equivalent.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Michael Pratt [Wed, 7 Sep 2022 14:29:49 +0000 (10:29 -0400)]
tools/autoconf-archive: clean up build recipes
The configure option datarootdir
defaults to PREFIX/share.
The Host/Clean define should be Host/Uninstall
otherwise it is removing the build directory
before there is a chance to try "make uninstall"
in that directory.
Host/Clean/Default is no longer defined.
Use default build recipes defined in host-build.mk
instead of custom ones that are equivalent.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Michael Pratt [Thu, 25 Aug 2022 02:32:13 +0000 (22:32 -0400)]
build: disable automake dependency tracking
Recent versions of Automake
have changed dependency tracking significantly
(reference commit below)
causing breakage in some package builds
when using newer Automake with packages that need autoreconf
that were bootstrapped with an old version of Automake.
Those changes cause a great inconsistency between packages over time
where some packages may or may not use this feature,
and may or may not update the .ac and .am files
to work with the new methods.
This problem might exist in many packages
where autoreconf is not currently required,
but would cause build failure if autoreconf is used.
Fortunately, this feature is practically useless
for the purposes of Openwrt and the average developer,
so we can disable it.
GNU Automake manual states in part:
"Because dependencies are only computed as a side-effect of compilation...
no dependency information exists the first time a package is built...
dependency tracking is completely useless for one-time builds..."
A nice side-effect is that build times are slightly faster.
Ref:
6a675ef17edf7109da189f5ae70e2dc6b7665896 (automake.git)
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Lech Perczak [Tue, 7 Mar 2023 00:14:05 +0000 (01:14 +0100)]
ath79: fix user LED glow on Mikrotik 911 Lite boards
GPIO3, to which the user LED is connected on RB911-Lite boards seems to
still sink current, even when driven high. Enabling open drain for this
pin fixes this behaviour and gets rid of the glow when LED is set to
off, so enable it.
Fixes: 43c7132bf8e7 ("ath79: add support for MikroTik RouterBOARD 911 Lite2/Lite5")
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Nick Hainke [Sat, 4 Mar 2023 22:19:37 +0000 (23:19 +0100)]
elfutils: update to 1.89
Release Notes:
https://sourceware.org/pipermail/elfutils-devel/2023q1/006023.html
Refresh patch:
- 003-libintl-compatibility.patch
Signed-off-by: Nick Hainke <vincent@systemli.org>
Nick Hainke [Sat, 4 Mar 2023 22:12:31 +0000 (23:12 +0100)]
tools/elfutils: update to 1.89
Release Notes:
https://sourceware.org/pipermail/elfutils-devel/2023q1/006023.html
Signed-off-by: Nick Hainke <vincent@systemli.org>
Nick Hainke [Fri, 3 Mar 2023 12:32:36 +0000 (13:32 +0100)]
strace: update to 6.2
Release Notes:
https://github.com/strace/strace/releases/tag/v6.2
Signed-off-by: Nick Hainke <vincent@systemli.org>
David Bauer [Tue, 16 Jun 2020 21:26:50 +0000 (23:26 +0200)]
ath79: refactor devolo WiFi pro image definitions
Reuse common parts for the devolo WiFi pro series. The series is
discontinued and we support all existing devices, so changes due to new
revisions or models are highly unlikely
Signed-off-by: David Bauer <mail@david-bauer.net>
Hauke Mehrtens [Fri, 10 Mar 2023 00:45:14 +0000 (01:45 +0100)]
kernel: modules: add missing kmod-mdio-devres for lan743x
This fixes a build problem on some targets.
Fixes: 3e9005546a ("kernel: modules: package Microchip LAN743x PCIe gigE driver")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Wed, 8 Mar 2023 22:59:48 +0000 (23:59 +0100)]
binutils: Deactivate msgpack
Deactivate the msgpack option. The binutils build might detect the
libmsgpackc.so.2 library and will try to link against it, if it is not
explicitly deactivated.
This prevents the following build errors seen in the build bots.
Package binutils is missing dependencies for the following libraries:
libmsgpackc.so.2
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Álvaro Fernández Rojas [Thu, 9 Mar 2023 17:54:59 +0000 (18:54 +0100)]
bmips: dts: fix warnings
- Add missing interrupt-parent to ext_intc.
- Add missing #address-cells and #size-cells to gpio_cntl.
- Use proper gpio handle for gpios (ar-5315u).
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Chuanhong Guo [Thu, 9 Mar 2023 09:24:43 +0000 (17:24 +0800)]
kernel: modules: add missing kmod-ptp for lan743x
Fixes: 3e9005546a ("kernel: modules: package Microchip LAN743x PCIe gigE driver")
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Tim Harvey [Tue, 7 Mar 2023 21:41:13 +0000 (13:41 -0800)]
kernel: modules: package Microchip LAN743x PCIe gigE driver
Package the Microchip LAN743x PCIe gigE driver
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
INAGAKI Hiroshi [Wed, 8 Mar 2023 12:54:14 +0000 (21:54 +0900)]
mvebu: add support for Fortinet FortiGate 50E
Fortinet FortiGate 50E (FG-50E) is a UTM, based on Armada 385 (
88F6820).
Specification:
- SoC : Marvell Armada 385
88F6820
- RAM : DDR3 2 GiB (4x Micron MT41K512M8DA-107, "D9SGQ")
- Flash : SPI-NOR 128 MiB (Macronix MX66L1G45GMI-10G)
- Ethernet : 7x 10/100/1000 Mbps
- LAN 1-5 : Marvell
88E6176
- WAN 1, 2 : Marvell
88E1512 (2x)
- LEDs/Keys : 18x/1x
- UART : "CONSOLE" port (RJ-45, RS-232C level)
- port : ttyS0
- settings : 9600bps 8n1
- assignment : 1:NC , 2:NC , 3:TXD, 4:GND,
5:GND, 6:RXD, 7:NC , 8:NC
- note : compatible with Cisco console cable
- HW Monitoring: nuvoTon NCT7802Y
- Power : 12 VDC, 2 A
- plug : Molex 5557-02R
Flash instruction using initramfs image:
1. Power on FG-50E and interrupt to show bootmenu
2. Call "[R]: Review TFTP parameters.", check TFTP parameters and
connect computer to "Image download port" in the parameters
3. Prepare TFTP server with the parameters obtained above
4. Rename OpenWrt initramfs image to "image.out" and put to TFTP
directory
5. Call "[T]: Initiate TFTP firmware transfer." to download initramfs
image from TFTP server
6. Type "r" key when the following message is showed, to boot initramfs
image without flashing to spi-nor flash
"Save as Default firmware/Backup firmware/Run image without saving:[D/B/R]?"
7. On initramfs image, backup mtd if needed
minimum:
- "firmware-info"
- "kernel"
- "rootfs"
7. On initramfs image, upload sysupgrade image to the device and perform
sysupgrade
8. Wait ~200 seconds to complete flashing and rebooting.
If the device is booted with stock firmware, login to bootmenu and
call "[B]: Boot with backup firmware and set as default." to set the
first OS image as default and boot it.
Notes:
- All "SPEED" LEDs(Green/Amber) of LAN and 1000M "SPEED" LEDs(Green) of
WAN1/2 are connected to GPIO expander. There is no way to indicate
link speed of networking device on Linux Kernel/OpenWrt, so those LEDs
cannot be handled like stock firmware.
On OpenWrt, use netdev(link) trigger instead.
- Both colors of Bi-color LEDs on the front panel cannot be turned on at
the same time.
- "PWR" and "Logo" LEDs are connected to power source directly.
- The following partitions are added for OpenWrt.
These partitions are contained in "uboot" partition (0x0-0x1fffff) on
stock firmware.
- "firmware-info"
- "dtb"
- "u-boot-env"
- "board-info"
Image header for bootmenu tftp:
0x0 - 0xf : ?
0x10 - 0x2f : Image Name
0x30 - 0x17f: ?
0x180 - 0x183: Kernel Offset*
0x184 - 0x187: Kernel Length*
0x188 - 0x18b: RootFS Offset (ext2)*
0x18c - 0x18f: RootFS Length (ext2)*
0x190 - 0x193: DTB Offset
0x194 - 0x197: DTB Length
0x198 - 0x19b: Data Offset (jffs2)
0x19c - 0x19f: Data Length (jffs2)
0x1a0 - 0x1ff: ?
*: required for initramfs image
MAC addresses:
(eth0): 70:4C:A5:xx:xx:7C (board-info, 0xd880 (hex))
WAN 1 : 70:4C:A5:xx:xx:7D
WAN 2 : 70:4C:A5:xx:xx:7E
LAN 1 : 70:4C:A5:xx:xx:7F
LAN 2 : 70:4C:A5:xx:xx:80
LAN 3 : 70:4C:A5:xx:xx:81
LAN 4 : 70:4C:A5:xx:xx:82
LAN 5 : 70:4C:A5:xx:xx:83
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Aleksey Nasibulin [Mon, 6 Mar 2023 10:49:33 +0000 (10:49 +0000)]
ramips: add support for SNR-CPE-ME2-SFP
SNR-CPE-ME2-SFP is a wireless router with SFP cage manufactured by SNR/NAG company.
Specification:
- SoC: MediaTek MT7621A
- CPU: 880MHz
- Flash: 16 MB (GD25Q127CSIG)
- RAM: 256 MB
- WLAN: 2.4 GHz, 5 GHz (MediaTek MT7615DN)
- Ethernet: 4x 10/100/1000 Mbps
- SFP cage (using RTL8211FS-CG)
- USB 3.0 port
- Power: 12 VDC, 2 A
Flash instruction via TFTP:
1. Boot SNR-CPE-ME2 to recovery mode
(press reset button and power on device, hold button for ~10 seconds)
2. Send firmware via TFTP client:
TFTP Server address: 192.168.1.1
TFTP Client address: 192.168.1.131
3. Wait ~120 seconds to complete flashing
4. Do sysupgrade using web-interface
MAC Addresses(stock)
--------------------
+----------+------------------+-------------------+
| use | address | example |
+----------+------------------+-------------------+
| Device | label | 6A:C4:DD:xx:xx:28 |
| Ethernet | + 1 | 6A:C4:DD:xx:xx:29 |
| 2g | + 2 | 6A:C4:DD:xx:xx:2A |
| 5g | + 3 | 6A:C4:DD:xx:xx:2B |
+----------+------------------+-------------------+
Notes:
- Reading sfp eeprom is not supported [1] (driver issue). Stock image has the same situation.
References:
1. https://forum.openwrt.org/t/mt7621-and-reading-sfp-eeprom/152249
Signed-off-by: Aleksey Nasibulin <alealexpro100@ya.ru>
David Bauer [Mon, 6 Mar 2023 20:27:49 +0000 (21:27 +0100)]
ipq40xx: convert Netgear EX6100/EX6150 v2 to DSA
Signed-off-by: David Bauer <mail@david-bauer.net>
Hauke Mehrtens [Mon, 6 Mar 2023 22:39:51 +0000 (23:39 +0100)]
kernel: Fix perf build with binutils 2.40
Backport patches from kernel 6.0 which are fixing building of perf with
binutils 2.40.
perf with kernel 5.10 is also not building but the backporting is more
complicated and only a few targets are still using kernel 5.10.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Felix Fietkau [Tue, 7 Mar 2023 20:53:00 +0000 (21:53 +0100)]
qosify: update to the latest version
ca4509cf84d2 bpf: switch to using bpf_skb_utils.h
d064439009d0 qosify-bpf: skip unnecessary flow lookups
9c625ae96f2d map: fix deleting port based rules
9a47ea4b683d map: fix return code check for bpf_map_get_next_key calls
Signed-off-by: Felix Fietkau <nbd@nbd.name>
David Bauer [Sat, 18 Feb 2023 01:06:54 +0000 (02:06 +0100)]
mpc85xx: add support for Watchguard Firebox T10
Hardware
--------
SoC: Freescale P1010
RAM: 512MB
FLASH: 1 MB SPI-NOR
512 MB NAND
ETH: 3x Gigabite Ethernet (Atheros AR8033)
SERIAL: Cisco RJ-45 (115200 8N1)
RTC: Battery-Backed RTC (I2C)
Installation
------------
1. Patch U-Boot by dumping the content of the SPI-Flash using a SPI
programmer. The SHA1 hash for the U-Boot password is currently
unknown.
A tool for patching U-Boot is available at
https://github.com/blocktrron/t10-uboot-patcher/
You can also patch the unknown password yourself. The SHA1 hash is
E597301A1D89FF3F6D318DBF4DBA0A5ABC5ECBEA
2. Interrupt the bootmenu by pressing CTRL+C. A password prompt appears.
The patched password is '1234' (without quotation marks)
3. Download the OpenWrt initramfs image. Copy it to a TFTP server
reachable at 10.0.1.13/24 and rename it to uImage.
4. Connect the TFTP server to ethernet port 0 of the Watchguard T10.
5. Download and boot the initramfs image by entering "tftpboot; bootm;"
in U-Boot.
6. After OpenWrt booted, create a UBI volume on the old data partition.
The "ubi" mtd partition should be mtd7, check this using
$ cat /proc/mtd
Create a UBI partition by executing
$ ubiformat /dev/mtd7 -y
7. Increase the loadable kernel-size of U-Boot by executing
$ fw_setenv SysAKernSize 800000
8. Transfer the OpenWrt sysupgrade image to the Watchguard T10 using
scp. Install the image by using sysupgrade:
$ sysupgrade -n <path-to-sysupgrade>
Note: The LAN ports of the T10 are 1 & 2 while 0 is WAN. You might
have to change the ethernet-port.
9. OpenWrt should now boot from the internal NAND. Enjoy.
Signed-off-by: David Bauer <mail@david-bauer.net>
Felix Fietkau [Tue, 7 Mar 2023 09:23:38 +0000 (10:23 +0100)]
hostapd: enable radius server support
This is useful in combination with the built-in eap server support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Tue, 7 Mar 2023 09:23:17 +0000 (10:23 +0100)]
hostapd: add missing return code for the bss_mgmt_enable ubus method
Fixes bogus errors on ubus calls
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Thu, 2 Mar 2023 11:49:10 +0000 (12:49 +0100)]
hostapd: add support for defining multiple acct/auth servers
This allows adding backup servers, in case the primary ones fail.
Assume that port and shared secret are going to be the same.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Paul Spooren [Wed, 22 Feb 2023 18:40:20 +0000 (19:40 +0100)]
at91: switch to Kernel 5.15 by default
Getting ready for the next release.
Claudiu said:
> I tested v5.15 on all targets I have access to previously, when
> updating OpenWrt kernel for v5.15 and when preparing this PR. (#11918)
Signed-off-by: Paul Spooren <mail@aparcar.org>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
John Audia [Fri, 3 Mar 2023 18:37:30 +0000 (13:37 -0500)]
kernel: bump 5.10 to 5.10.172
Removed upstreamed:
backport-5.10/804-0001-net-Remove-WARN_ON_ONCE-sk-sk_forward_alloc-from-sk_.patch[1]
All other patches automatically rebased.
1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.171&id=
3e4bbd1f38a8d35bd2d3aaffdb5f6ada546b669a
Signed-off-by: John Audia <therealgraysky@proton.me>
John Audia [Mon, 27 Feb 2023 22:58:42 +0000 (17:58 -0500)]
kernel: bump 5.10 to 5.10.170
No patches modified for this bump
Signed-off-by: John Audia <therealgraysky@proton.me>
John Audia [Sat, 25 Feb 2023 21:20:28 +0000 (16:20 -0500)]
kernel: bump 5.10 to 5.10.169
Manually rebased:
backport-5.10/811-v6.1-0001-nvmem-core-Fix-memleak-in-nvmem_register.patch
Removed upstreamed:
backport-5.10/811-v6.1-0003-nvmem-core-add-error-handling-for-dev_set_name.patch[1]
patches-5.10/070-net-bgmac-fix-BCM5358-support-by-setting-correct-fla.patch[2]
Add fix:
target/linux/generic/backport-5.10/804-0001-net-Remove-WARN_ON_ONCE-sk-sk_forward_alloc-from-sk_.patch[3]
All other patches automatically rebased.
1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.169&id=
a19a0f67dbb89ad2bfc466f2003841acba645884
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.169&id=
a5c51e0c3202820192db3f3809e072f3ca2b1177
3. https://lore.kernel.org/stable/
20230227211548.13923-1-kuniyu@amazon.com
Signed-off-by: John Audia <therealgraysky@proton.me>
Eneas U de Queiroz [Mon, 6 Mar 2023 14:58:56 +0000 (11:58 -0300)]
openssl: fix variable reference in conffiles
Fix the trivial abscence of $() when assigning engine config files to
the main libopenssl-config package even if the corresponding engines
were not built into the main library.
This is mostly cosmetic, since scripts/ipkg-build tests the file's
presence before it is actually included in the package's conffiles.
Fixes: 30b0351039 "openssl: configure engine packages during install"
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Eneas U de Queiroz [Mon, 6 Mar 2023 14:58:56 +0000 (11:58 -0300)]
openssl: fix sysupgrade failure with devcrypto
The bump to 3.0.8 inadvertently removed patches that are needed here,
but were not adopted upstream. The most important one changes the
default value of the DIGESTS setting from ALL to NONE. The absence of
this patch causes a sysupgrade failure while the engine is in use with
digests enabled. When this happens, the system fails to boot with a
kernel panic.
Also, explicitly set DIGESTS to NONE in the provided config file, and
change the default ciphers setting to disable ECB, which has been
recommended for a long time and may cause trouble with some apps.
The config file change by itself is not enough because the config file
may be preserved during sysupgrade.
For people affected by this bug:
You can either:
1. remove, the libopenssl-devcrypto package
2. disable the engine in /etc/config/openssl;
3. change /etc/ssl/engines.cnf.d/devcrypto.cnf to set DIGESTS=NONE;
4. update libopenssl-devcrypto to >=3.0.8-3
However, after doing any of the above, **you must reboot the device
before running sysupgrade** to ensure no running application is using
the engine. Running `/etc/init.d/openssl restart` is not enough.
Fixes: 7e7e76afca "openssl: bump to 3.0.8"
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Hauke Mehrtens [Sun, 26 Feb 2023 14:47:09 +0000 (15:47 +0100)]
binutils: Update to version 2.40
binutils 2.39: https://lists.gnu.org/archive/html/info-gnu/2022-08/msg00002.html
binutils 2.40: https://lists.gnu.org/archive/html/info-gnu/2023-01/msg00003.html
This version includes a new libsframe.so library, pack it into the
libbfd package as it is used by this library. Also deactivate some
optional configuration options for now.
An extra patch to fix compile problem in AARCH64 is added.
gprofng needs a C++ standard library, deactivate it for now.
Activate feature-disassembler-init-styled in bpftools too to fix
compilation with the updated binutils.
An bpftool version 7.0 or later is needed for binutils 2.39 and later.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sat, 25 Feb 2023 21:21:15 +0000 (22:21 +0100)]
bpftool: Update to version 7.1.0
bpftool changelog: https://github.com/libbpf/bpftool/releases
libbpf changelog: https://github.com/libbpf/libbpf/releases
This updates the bfptool to version 7.1.0. This also includes an update
of the libbpf to version 1.1.
This also adds some new feature options and removes some old ones which
were also removed form the source code. zlib for example is now
mandatory.
Add -flto also to LD flags to make it really work.
Before this change bpftool was on a git commit between version 6.7 and
6.8 and libbpf was on a commit between version 0.7 and 0.8.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Rosen Penev [Wed, 15 Feb 2023 03:31:03 +0000 (19:31 -0800)]
mac80211: enable ATH9K_HWRNG
in kernel 5.17,
fcd09c90c3c5254b18ef34e30c57c65d34290a84 integrated it
better with thee random framework.
Gives boot time randomness on supported devices.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Rosen Penev [Wed, 1 Feb 2023 22:50:22 +0000 (14:50 -0800)]
ksmbd: update to 3.4.7
Remove upstreamed patches.
Switch to normal tarballs. Codeload recently had a reproducibility issue.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Hauke Mehrtens [Sun, 5 Mar 2023 17:42:49 +0000 (18:42 +0100)]
bcm47xx: Refresh patches
The kernel patches did not apply cleanly any more, refresh them
automatically.
Fixes: 26bc8f68767e ("generic: MIPS: Add barriers between dcache & icache flushes")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tomasz Maciej Nowak [Fri, 17 Feb 2023 13:21:01 +0000 (14:21 +0100)]
sdk: expose PATENTED an NLS build options
Some packages offer functionalities guarded by these options and it'll
be impossible to reach them without changing Config-build.in. So allow
to toggle these in more friendly way, by exposing them in configuration
menu.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Paul Fertser [Fri, 20 Jan 2023 15:25:13 +0000 (18:25 +0300)]
Remove ccache wrappers
These wrappers are not needed as CC doesn't need to be a single word.
a53b084e497a9f1629a2caada833ebe14a6838b7 which introduced the wrappers
doesn't explain why they were really needed and why only for the target
and not for the host.
Moreover, name of the wrappers breaks a ccache assumption: since
v4.0-3-g6a92b4cd3a67 it has special handling for "chained" invocation
such as "ccache ccache gcc" where it skips all the "ccache*" names in
the middle and proceeds to run as if it was started as "ccache
gcc"[1][2].
This becomes important when a build system sees ccache in the PATH and
automatically enables it by prepending to CC. An example of such a
system would be autosetup as used by jimtcl. With the wrappers it breaks
as the command line ends up being just "ccache -Os..." because
"ccache_cc" gets skipped as it starts with "ccache".
[1] https://github.com/ccache/ccache/blob/master/src/ccache.cpp#L2105
[2] https://github.com/ccache/ccache/blob/master/src/Util.cpp#L802
Reported-by: Karl Palsson <karlp@etactica.com>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Stijn Tintel [Mon, 20 Feb 2023 14:00:54 +0000 (16:00 +0200)]
kernel: set default for KERNEL_BPF_KPROBE_OVERRIDE
Without the default value this still causes a missing symbol. Disable by
default as it depends on FUNCTION_ERROR_INJECTION, which is disabled in
the generic config and we don't have a build symbol to enable that.
Fixes: 500c37c56ff6 ("kernel: add missing symbol")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Felix Fietkau [Sun, 5 Mar 2023 16:25:34 +0000 (17:25 +0100)]
mediatek: backport more WED upstream fixes
Fixes hang if the WO firmware can't be loaded
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Alan Luck [Sun, 26 Feb 2023 06:17:37 +0000 (22:17 -0800)]
ipq806x: Add buttons to OnHub
These are the factory reset button (external) and "developer mode"
button (hidden inside the case (ASUS) or under a screw in the base
(TP-Link)) found on the TP-Link and ASUS OnHub devices.
Signed-off-by: Alan Luck <luckyhome2008@gmail.com>
[Brian: add description; factor out for both ASUS and TP-Link; use
existing pinmux definitions; add keycode for dev button]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tim Harvey [Tue, 28 Feb 2023 00:13:07 +0000 (16:13 -0800)]
kernel: add kmod-hwmon-max6642 support
Add package for Maxim MAX6642 i2c based temperature sensor.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Hauke Mehrtens [Sun, 5 Mar 2023 15:39:24 +0000 (16:39 +0100)]
uci: update to git HEAD
5de3871 cli: drop redundant uci_add_delta_path() call for -P
f49a2fd delta: simplify uci_load_delta() by using a helper
9b6605e uci: fix use-after-free uci_set on update option
b7ceda9 uci: maintain option position in uci_set
7e01d66 uci: optimize update option in uci_set
47697e6 uci: fix use-after-free uci_add_list
74f2797 uci: fix atomicity of uci_add_list
b2f3417 uci: maintain option position in uci_add_list
16e8a3b uci: fix memory leak uci_set on update section
ae61e1c uci: optimize update section in uci_set
04d0c46 uci: macro uci_alloc_element not in uci.h
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Álvaro Fernández Rojas [Sun, 5 Mar 2023 10:51:46 +0000 (11:51 +0100)]
Revert "bmips: add missing switch cpu label"
This reverts commit
dc0de05e10a9c6e1ef66ca2934e8a0ff0d488943.
As pointed out by @BKPepe and @arinc9 this was removed by
9df035b since it
isn't needed.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Felix Fietkau [Sun, 5 Mar 2023 08:58:40 +0000 (09:58 +0100)]
mediatek: add missing DTS entries for WED on MT7986
Needed to support WLAN offloading
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Sat, 4 Mar 2023 18:11:37 +0000 (19:11 +0100)]
kernel: backport upstream mtk_eth_soc fixes
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Sat, 4 Mar 2023 16:57:46 +0000 (17:57 +0100)]
kernel: move accepted mtk_eth_soc patches to generic-backport
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Nick Hainke [Wed, 1 Mar 2023 21:18:14 +0000 (22:18 +0100)]
dtc: update to 1.7.0
Changelog:
039a994 Bump version to v1.7.0
3f29d6d pylibfdt: add size_hint parameter for get_path
2022bb1 checks: Update #{size,address}-cells check for 'dma-ranges'
abbd523 pylibfdt: Work-around SWIG limitations with flexible arrays
a41509b libfdt: Replace deprecated 0-length arrays with proper flexible arrays
2cd89f8 dtc: Warning rather than error on possible truncation of cell values
55778a0 libfdt: tests: add get_next_tag_invalid_prop_len
7359034 libfdt: prevent integer overflow in fdt_next_tag
035fb90 libfdt: add fdt_get_property_by_offset_w helper
98a0700 Makefile: fix infinite recursion by dropping non-existent `%.output`
a036cc7 Makefile: limit make re-execution to avoid infinite spin
c6e9210 libdtc: remove duplicate judgments
e37c256 Don't generate erroneous fixups from reference to path
5045465 libfdt: Don't mask fdt_get_name() returned error
e64a204 manual.txt: Follow README.md and remove Jon
f508c83 Update README in MANIFEST.in and setup.py to README.md
c2ccf8a Add description of Signed-off-by lines
90b9d9d Split out information for contributors to CONTRIBUTING.md
0ee1d47 Remove Jon Loeliger from maintainers list
b33a73c Convert README to README.md
7ad6073 Allow static building with meson
fd9b8c9 Allow static building with make
fda71da libfdt: Handle failed get_name() on BEGIN_NODE
c7c7f17 Fix test script to run also on dash shell
01f23ff Add missing relref_merge test to meson test list
ed31080 pylibfdt: add FdtRo.get_path()
c001fc0 pylibfdt: fix swig build in install
26c54f8 tests: add test cases for label-relative path references
ec7986e dtc: introduce label relative path references
651410e util: introduce xstrndup helper
4048aed setup.py: fix out of tree build
ff5afb9 Handle integer overflow in check_property_phandle_args()
ca72944 README: Explain how to add a new API function
c0c2e11 Fix a UB when fdt_get_string return null
cd5f69c tests: setprop_inplace: use xstrdup instead of unchecked strdup
a04f690 pylibfdt: add Property.as_*int*_array()
8310271 pylibfdt: add Property.as_stringlist()
d152126 Fix Python crash on getprop deallocation
17739b7 Support 'r' format for printing raw bytes with fdtget
45f3d1a libfdt: overlay: make overlay_get_target() public
c19a4ba libfdt: fix an incorrect integer promotion
1cc41b1 pylibfdt: Add packaging metadata
db72398 README: Update pylibfdt install instructions
383e148 pylibfdt: fix with Python 3.10
23b56cb pylibfdt: Move setup.py to the top level
69a7607 pylibfdt: Split setup.py author name and email
0b106a7 pylibfdt: Use setuptools_scm for the version
c691776 pylibfdt: Use setuptools instead of distutils
5216f3f libfdt: Add static lib to meson build
4eda259 CI: Cirrus: bump used FreeBSD from 12.1 to 13.0
0a3a9d3 checks: Add an interrupt-map check
8fd2474 checks: Ensure '#interrupt-cells' only exists in interrupt providers
d8d1a9a checks: Drop interrupt provider '#address-cells' check
52a16fd checks: Make interrupt_provider check dependent on interrupts_extended_is_cell
37fd700 treesource: Maintain phandle label/path on output
e33ce1d flattree: Use '\n', not ';' to separate asm pseudo-ops
d24cc18 asm: Use assembler macros instead of cpp macros
ff3a30c asm: Use .asciz and .ascii instead of .string
5eb5927 fdtdump: fix -Werror=int-to-pointer-cast
0869f82 libfdt: Add ALIGNMENT error string
69595a1 checks: Fix bus-range check
72d09e2 Makefile: add -Wsign-compare to warning options
b587787 checks: Fix signedness comparisons warnings
69bed6c dtc: Wrap phandle validity check
9102211 fdtget: Fix signedness comparisons warnings
d966f08 tests: Fix signedness comparisons warnings
ecfb438 dtc: Fix signedness comparisons warnings: pointer diff
5bec74a dtc: Fix signedness comparisons warnings: reservednum
24e7f51 fdtdump: Fix signedness comparisons warnings
Remove upstreamed:
- 0001-Support-r-format-for-printing-raw-bytes-with-fdtget.patch
Signed-off-by: Nick Hainke <vincent@systemli.org>
Nick Hainke [Wed, 1 Mar 2023 20:14:54 +0000 (21:14 +0100)]
mac80211: refresh patches
The last mac80211 commits did not refresh the patches.
Refresh:
- ath/402-ath_regd_optional.patch
- ath10k/080-ath10k_thermal_config.patch
- ath10k/974-ath10k_add-LED-and-GPIO-controlling-support-for-various-chipsets.patch
- ath9k/551-ath9k_ubnt_uap_plus_hsr.patch
- rt2x00/602-rt2x00-introduce-rt2x00eeprom.patch
Signed-off-by: Nick Hainke <vincent@systemli.org>
Álvaro Fernández Rojas [Sat, 4 Mar 2023 20:27:30 +0000 (21:27 +0100)]
bmips: add missing switch cpu label
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Daniel González Cabanelas [Mon, 19 Dec 2022 14:25:30 +0000 (15:25 +0100)]
bcm63xx: kernel: power cycle the bcm6358 USB PLL
Some BCM6358 based boards may detect USB2.0 high speed devices as USB1.1
full speed. This is an old well known bug, but nobody cared about it. It
is quite random and hard to track.
With the latest versions of Openwrt, one user confirmed that the bug is
still there (tested router: HG556a).
Power cycle the USB PLL to fix it.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
Daniel González Cabanelas [Mon, 19 Dec 2022 14:21:28 +0000 (15:21 +0100)]
bcm63xx: kernel: fix up bcm63268 roboswitch gpio registers
Some BCM63268 bootloaders may leave gpio registers, related to the
roboswitch, disabled before loading the OpenWrt firmware. As result of
this the switch won't work.
These registers, if not enabled, probably avoid forwarding packets.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
Álvaro Fernández Rojas [Sat, 4 Mar 2023 18:47:06 +0000 (19:47 +0100)]
bcm63xx: drop kernel 5.10 support
Now that the target is on kernel 5.15 this is no longer needed.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Paul Spooren [Wed, 22 Feb 2023 18:50:58 +0000 (19:50 +0100)]
bcm63xx: switch to Kernel 5.15 by default
Getting ready for the next release.
Signed-off-by: Paul Spooren <mail@aparcar.org>
projects / openwrt / staging / hauke.git / log