brcmsmac: remove dependency on CRC8 and CRC_CCITT

There is no code in brcmsmac that uses a function from CRC8 or
CRC_CCITT any more. Building brcmsmac with these two disabled works
without any problems. This was probably only used by the bus code which
was replaced by bcma some time ago.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: fix retry chain initialization in tx99 code

Initialize first chain attempt counter to 1 in ath9k_build_tx99_skb().
Otherwise multi-retry chain is initialized to {idx,count} = {-1, 0} in
rate_control_fill_sta_table() and tx99 transmission rate is not configured in
rate_control_apply_mask() since first chain idx is set to -1

Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wcn36xx: set self STA default HT parameters

These default HT parameters are required for self STA entry.
In example, set the HT capable of self STA entry for bss
configuration in mesh allows the MCS rate to be used. Otherwise,
only legacy rate will be used.

Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas sdio: claim device before calling sdio_disable_func()

There is a failure path in if_sdio_power_on(), where
sdio_disable_func() is called without claiming the device.

Found by Linux Driver Verification project (linuxtesting.org).

Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8192cu: Update table.c

The latest vendor driver has some new values.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8192cu: Bring rtl92cu_phy_bb_config() up to date

The latest vendor driver contains some changes not in the kernel version.

Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: Bring _rtl92c_phy_iq_calibrate() in line with the vendor driver

Bring _rtl92c_phy_iq_calibrate() in line with the vendor driver function _PHY_IQCalibrate().

Also fix incorrect initialisation for rtl8192cu.

Signed-of-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8192c: Update dynamic gain calculations

The vendor driver contained a number of improvements in the gain settings
for the rtl8192c{e,u} devices. This patch implements them in the kernel
driver.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: Add missing code to PWDB statics routine

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8192cu: Fix some code in RF handling

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8192cu: Update the power index registers

This patch uses the newly introduced power index register routines.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8192c: Add routines to save/restore power index registers

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: Update beacon statistics for USB driver

The USB drivers were not updating the beacon statistics, which led to
false beacon loss indications.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: Increase the RX queue length for USB drivers

The current number of RX buffers queued is 32, which is too small under
heavy load. That number is doubled.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8192c: Add new definitions in the dm_common header

Changes in the gain-control mechanism will require some changes in the header.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: Set the link state

The present code fails to set the linked state when an interface is
added.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: Redo register save locations

The initial USB driver did not use some register save locations in the
private data storage. To save some memory, a union was used to overlay these
variables with USB I/O components. In an update of the gain-control code,
these register save locations are now needed for USB drivers.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8192cu: Add new firmware

Vendor driver rtl8188C_8192C_8192D_usb_linux_v3.4.2_3727.20120404 introduced
new firmware for these chips. The code try for the new file, and fall back to
the original firmware if the new file is not available.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8192c: Prevent reconnect attempts if not connected

This driver has a watchdog timer that attempts to reconnect when beacon frames
are not seen for 6 seconds. This patch disables that reconnect whenever the
device has never been connected.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: rt2800lib: no need to write RF register 3 twice for RT5592

In rt2800_init_rfcsr_5592(), there's no need to write RF register 3 twice.

Signed-off-by: Kevin Lo <kevlo@kevlo.org>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: Remove unused calls to rtl_is_special_data()

When routine rtl_is_special_data() is called with false as its last argument,
and the returned value is not tested, the call is essentially an extended
no-op. Accordingly, these calls may be removed.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wcn36xx: Fix logging macro with unnecessary semicolon

The wcn36xx_err macro should not end in a semicolon as
there are 2 consecutive semicolons in the preprocessed
output.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Eugene Krasnikov <k.eugene.e@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wcn36xx: enable beacon change using BSS_CHANGED_BEACON

Enable the beacon changed using BSS_CHANGED_BEACON. This is
especially useful for mesh mode.

Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtl8187: Increase RX queue depth

Under heavy load, the relatively small number of RX queue entries are
completely filled. With an increase from 16 to 32 entries, this condition
rarely happens.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: fix usage of freq_reg_info()

freq_reg_info() expects KHz and not MHz, fix this. In
this case we'll now be getting the no-ir flags cleared
on channels for any channel when the country IE trusts
that channel.

@@
struct ieee80211_channel *ch;
struct wiphy *wiphy;
const struct ieee80211_reg_rule *rule;
@@

-rule = freq_reg_info(wiphy, ch->center_freq);
+rule = freq_reg_info(wiphy, MHZ_TO_KHZ(ch->center_freq));

Generated-by: Coccinelle SmPL
Cc: Julia Lawall <julia.lawall@lip6.fr>
Cc: Peter Senna Tschudin <peter.senna@gmail.com>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: Mihir Shete <smihir@qti.qualcomm.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: fix usage of freq_reg_info()

freq_reg_info() expects KHz and not MHz, fix this. In
this case we'll now be getting the no-ir flags cleared
on channels for any channel when the country IE trusts
that channel.

@@
struct ieee80211_channel *ch;
struct wiphy *wiphy;
const struct ieee80211_reg_rule *rule;
@@

-rule = freq_reg_info(wiphy, ch->center_freq);
+rule = freq_reg_info(wiphy, MHZ_TO_KHZ(ch->center_freq));

Generated-by: Coccinelle SmPL
Cc: Julia Lawall <julia.lawall@lip6.fr>
Cc: Peter Senna Tschudin <peter.senna@gmail.com>
Cc: Seth Forshee <seth.forshee@canonical.com>
Cc: Arend van Spriel <arend@broadcom.com>
Reported-by: Mihir Shete <smihir@qti.qualcomm.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wireless: cw1200: Use consistent internal locking conventions

The cw1200_irq_handler() function expects the hwbus lock to be held when
it is called.  On the SDIO platform, this lock is implemented in terms
of sdio_claim_host/sdio_release_host.

This trivial patch makes it explicit that we are performing the hwbus
lock rather than something SDIO-specific.

Signed-off-by: Solomon Peachy <pizza@shaftnet.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cw1200: Make the "scan failed" message into a warning

The reason that a scan failed for some reason (typically bad
parameters) should be logged even when debugging is turned off.

Signed-off-by: Solomon Peachy <pizza@shaftnet.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwl3945: do not print RFKILL message

We can mess logs if user space try to open device again and again if
RFKILL switch is on. Do not print message and return ERFKILL error
instead to indicate where the problem is.

Note that iwl4965 handle this problem differently, it allows to open
device when radio is disabled.

Reported-by: Dietmar Rudolph <dietmar@crlf.de>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl1251: return -ENOMEM if kzalloc fails

the original code used goto out if kzalloc fails,but the out include kfree,
so return -ENOMEM if kzalloc fails.

Signed-off-by: Jing Wang <windsdaemon@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas/sdio: make sure card enters power-off when firmware is loaded.

Since firmware loading became async it is possible that if_sdio_finish_power_of
is called with only one remaining runtime_pm reference, so it isn't safe
to call pm_runtime_put_noidle.  We must call pm_runtime_put().

Diagnosed-by: "Dr. H. Nikolaus Schaller" <hns@goldelico.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: rt2800lib: update RF registers for RT5390

Mirror the latest MediaTek/Ralink driver with respect to RT5390 RF register
programming.  The PCI and USB devices use different init values.

Signed-off-by: Kevin Lo <kevlo@kevlo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: improvements in mwifiex_ret_tx_power_cfg()

1) Move common code out of switch case handling
2) Return from the function if number of bytes left in response buffer
are less than tlv size
3) Pass pg_tlv_hdr directly instead of txp_cfg to mwifiex_get_power_level()

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: rt2800lib: Update BBP register initialization for RT53xx

Update bbp register initialization for RT53xx chips to match with the
latest MediaTek/Ralink driver.

Based on: NICInitRT5390BbpRegisters()
From: DPO_RT5572_LinuxSTA_2.6.1.3_20121022/chips/rt5390.c

Signed-off-by: Kevin Lo <kevlo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'for-john' of git://git./linux/kernel/git/jberg/mac80211-next

brcmfmac: expose chip information through debugfs

Adding the debugfs file <debugfs_mnt>/brcmfmac/<devid>/chipinfo
which contains the chip number and revision.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: move firmware event related defines to fweh.h

The dhd.h file contained a number of definitions that are
related to events received from the firmware. Those are
processed and dispatched in the driver by fweh. Hence the
definitions are moved to its include file.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: remove some unused definitions

Removing WLC_PHY_TYPE and some BRCMF_E_.* definitions as these
are not used in the driver sources.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: Use consistent naming for BCDC.

The BCDC protocol layer is using a mix of naming of CDC, BDC and
BCDC. Use the name BCDC consistenly over all functions, defines
and variables. This patch does not change code functionality.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: move firmware command code definitions

Move the command codes to the firmware interface module as
that makes a bit more sense.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: move firmware related structures to fwil_types.h

The firmware control interface is provided by fwil source file, but
a number of structures used to communicate with the firmware still
resided in dhd.h. The patch moves them to fwil_types.h.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: remove unnecessary EXPORT_SYMBOL() usage

In bcmsdh.c the functions brcmf_sdio_probe() and brcmf_sdio_remove()
were exported, but that is not needed. The functions are linked into
the driver module, which is the only one needing to call these.

Reviewed-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: provide firmware version in ethtool driver info

Knowing the firmware version is pretty useful information when
looking at issues. It is retrieved during initialization so
store it in driver data structure to fill the ethtool driver
info when requested.

Reviewed-by: Hante Meuleman <meuleman@brodcom.com>
Reviewed-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: Dynamically register a protocol layer.

BCDC is the default protocol layer and being called directly. This
patch installs the functions for this layer dynamically. This allows
new protocols to be added and selected dynamically depending on the
hw capabilties. As currently only BCDC is supported this is always
the installed protocol.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: remove redundant ioctl handlers

The ioctl() entry points were empty except for handling SIOC_ETHTOOL
but that has been obsoleted in favor of struct ethtool_ops. Cleaning
up removing the ioctl() handlers.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: use platform specific alignment in SDIO

The SDIO part of the brcmfmac driver uses a static define BRCMF_SDALIGN
to align buffers used for SDIO transfers. This patch replaces it by
using alignment derived from the platform specific data.

Reviewed-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: determine alignment values during probe

The alignment values were being determined for each transmit
and receive depending on platform data. Instead determine
these once during the probe.

Reviewed-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: removed dhd_proto.h.

dhd_proto.h was cleaned up and prototypes were moved to dhd.h.
dhd_proto.h was removed. This is a step in cleaning and
restucturing protocol layer.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: rename dhd_cdc to bcdc

dhd_cdc is renamed to bcdc. This is a step in cleaning and
restructuring protocol layer. This is done so new protocols can
be added in the future. This step only renames the source files.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
[arend@broadcom.com: use 'git mv' to do the rename]
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: add host tx glomming support

New WiFi full dongle supports receiving chained packets in one command
through the SDIO bus. This patch adds the support on the host side to
send chained packets.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: add firmware and nvram file name for bcm4339

Add firmware/nvram file name for bcm4339 so fmac can actually be functional with
the chip.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: fix driver build issue when CONFIG_BRCMDBG is not set

When CONFIG_BRCMDBG is not set we get the following build issue:
  CC [M]  drivers/net/wireless/brcm80211/brcmfmac/fwsignal.o
drivers/net/wireless/brcm80211/brcmfmac/fwsignal.c:
    In function ‘brcmf_fws_hdrpush’:
drivers/net/wireless/brcm80211/brcmfmac/fwsignal.c:852:18:
error: ‘BRCMF_FWS_TYPE_SEQ_LEN’ undeclared

The define BRCMF_FWS_TYPE_SEQ_LEN was introduced by:

    commit 6918f38e4ed4e0493a90a4331e0033bdfc806e00
    Author: Hante Meuleman <meuleman@broadcom.com>
    Date:   Wed Oct 23 14:58:51 2013 +0200

        brcmfmac: Update fwsignal to fix out of order tx.

Unfortunately, it was put in conditional part of the source
file under #ifdef DEBUG.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: determine sd host controller related variable earlier

The commit "eb9c174 brcmfmac: determine host controller related
variables during probe" was not implemented correctly as the
information is already needed in brcmf_sdbrcm_probe(). This patch
moves it to brcmf_sdioh_attach() instead.

Reviewed-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: support hardware extension header in trace_brcmf_sdpcm_hdr()

The SDPCM header can be traced, but it used a fixed header size. With
txglom feature the SDPCM header will have additional 8 bytes of hardware
extension header so SDIO core can properly handle the txglom packet.

Reviewed-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmsmac: select CONFIG_BCMA when possible

The brcmsmac relies BCMA functionality to access the device. This
patch selects CONFIG_BCMA when CONFIG_BCMA_POSSIBLE is set. This
way the user does not need to be select BCMA to make the brcmsmac
driver show up in his menuconfig.

Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: reduce logging noise accessing SDIO SleepCSR register

The SleepCSR register is accessed to wakeup the device from the
host side. Depending on the state of the device this may take
multiple attempts. The failed attempt are not real failures so
reduce the log level specifically for this register. The calling
function will scream when the multiple attempts all failed.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: remove empty brcmf_proto_stop

remove empty brcmf_proto_stop from protocol layer

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: start netif queues only when setup is completed successful

Moving the call to netif_start_queue() after brcmf_cfg80211_up() is
completed successful. If not return -EIO instead of -1 as that results
in 'Operation not permitted' which can put user on wrong track.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: replace dongle command list with .preinit() callback

The bus-specific interface allowed a list of dongle commands to be
provided to the common driver part. However, upcoming functionality
requires a more dynamic behaviour. Hence the list is replaced
by a new callback function so the bus-specific driver part can
implement this behaviour.

Reviewed-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: add separate function for passing bus tx overhead

The common driver needs the packet overhead for the bus in order
to reserve headroom for sk_buffs. For the SDIO driver this depends
on firmware features so it is not possible to provide it in the
brcmf_attach() call.

Reviewed-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: Update fwsignal to fix out of order tx.

When using fwsignal it is possible that tx packets get delivered out
of order. This patch fixes that by reordering suppressed packets and
tracking generation bit and sequence number per packet.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Fix initvals for freq 2484

This is missing for AR9300, AR9580 and AR9340.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Update AR9340 initvals

* Baseband updates
* Remove ar9340Common_rx_gain_table_1p0 since it is a duplicate.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Update initvals for AR9580 v1.0

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Update initvals for AR9300 v2.2

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Remove duplicate initvals for AR9462 v2.1

The initvals for AR9462 v2.1 are very similar to v2.0.
Identify duplicate arrays and reuse the values from v2.0
to reduce module size.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Attach INI arrays for AR9565 v1.1

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Add version macros for AR9565 1.1

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Add initvals for AR9565 1.1

The initialization arrays for v1.1 AR9565
are mostly the same as v1.0/v1.0.1 except for
radio_postamble.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Cleanup IQ calibration for PCOEM chips

Since IQ calibration is done as part of AGC calibration for
AR9485 and above, remove the seperate IQ calibration code.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: allow fast channel change when only CHANNEL_HT changes

The CHANNEL_HT flag is insignificant for fast channel change conditions,
since it does not affect any important part of the hardware reset /
channel setup.
Scanning usually runs with HT disabled, so this change will slightly
improve scan time on many chipsets.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: fix TSF save/restore around chip reset

A cold reset can be triggered because of DMA stop issues, and this leads
to TSF being cleared on all chipsets. To properly deal with this, always
save the TSF.
Additionally, account for the time it takes to do the actual chip reset,
which can be quite significant. On AR9344 it takes around 4.5 ms.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: optimize ath9k_flush

Instead of checking the queues in a loop with hardcoded sleep times
inbetween, use a wait queue to trigger queue checks after the tx
processing tasklet has run.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: optimize ath_drain_all_txq

If the software has processed all packets, checking the hardware queue
is unnecessary.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: use a timer to put hardware into full sleep

When operating in client mode, the short period of time between scanning
and associating is often enough to put the hardware through several
FULL-SLEEP <-> AWAKE transitions, each wakeup requiring a reset to fully
recover the hardware.
This is completely unnecessary and can easily be avoided by deferring
the switch to full sleep.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Fix TX IQ calibration for SoC chips

Since calibration data reuse is not enabled in
SoC chips, simplify the IQ calibration code.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Fix Carrier Leak calibration for SoC chips

CL calibration is applicable for all chips and the
enable/disable knob comes via the INI file. For PCOEM
chips, the calibration data is reused when Fast Channel Change
is used. Caldata reuse is not enabled for SoC chips, so remove
the CL post processing code.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Remove unnecessary check

TX IQ calibration is always enabled for SoC chips.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Remove RTT/MCI code from SoC calibration

RTT is enabled only for AR9462 and MCI for AR9462/AR9565.
Also, manual peak calibration is not done for any of the
SoC chips.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Separate routines for PCOEM and SoC calibration

Though there is some overlap between the calibration mechanisms
of PC-OEM cards and SoC chip families, dumping both of them
into a single function makes things hard to understand.

ar9003_hw_init_cal() is unreadable with chip-specific segments
scattered around. To make the logic understandable, use
different functions for client cards and SoC chips. Some
code is duplicated, but in the long run, it makes the code
more maintanable.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: fix SC_OP_INVALID test in ath9k_tx99_init()

SC_OP_INVALID is zero so the test is always false.  We're supposed to be
testing the lowest bit instead.

Fixes: 89f927af7f33 ('ath9k: add TX99 support')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Update MAINTAINERS

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Apply CUS227 specific TX gain values

CUS227, which is an AR9340 based card used in Qualcomm's
Allplay platforms requires a custom TX gain array, based
on the index 7. Add suport for this.

Cc: Michael Larson <mlarson@qce.qualcomm.com>
Cc: Stephen Collmeyer <scollmey@qce.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Remove pcieSerDesWrite

This HW config option is always set to true and is not needed.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Remove unused AR9462 2.0 initvals

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Add SERDES initvals for AR9462 2.1

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Add an initialization routine for WoW

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Use CONFIG_ATH9K_WOW

Move the WoW code to wow.c and compile it conditionally
based on CONFIG_ATH9K_WOW.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Add a config option for WoW

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Fix wow.c compilation

The HW routines to set various WoW registers are present
in wow.c. For some reason, it has been compiled as part
of the main ath9k.ko module all this time, when it should
really be part of ath9k_hw.ko. This patch renames the file to
ar9003_wow.ko and adds it to ath9k_hw.ko.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Fix TX99 config option usage

Use CONFIG_ATH9K_TX99 to properly enclose the tx99 code
and make sure that it is not compiled as part of the driver
when it is not selected. Move the tx99 code to a new file tx99.c
and also add ATH9K_DEBUGFS as a dependency in Kconfig.

This reduces the module size on platforms like OpenWrt where
ATH9K_DEBUGFS is selected, but TX99 might be disabled.

Cc: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Identify Killer Wireless cards

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Add WB335 PCI IDs

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: fix rx_nss calculation for drivers with hw rc

Drivers with hardware rate control were given
sta->rx_nss set to 0. This was because rx_nss
calculation procedure was protected by hw/sw rate
control check.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: don't leak next beacon when csa is aborted

Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: don't cancel csa finalize work within stop_ap

The current channel switch code has a potential deadlock:
1) * cfg80211_stop_ap acquires wdev-lock
   * ieee80211_stop_ap calls cancel_work_sync for the csa_finalize_work,
     which acquires the associated worker-lock
2) * ieee80211_csa_finalize_work holds the worker-lock when run
   * it calls cfg80211_ch_switch_notify which will claim the wdev-lock,
     and also needs to claim the sdata-lock (which is the same as the
     wdev-lock) to modify the beacons.

It is sufficient to just set the channel switch active to false. If the
worker is running later, it will find the channel switch to not be
active anymore and returns immediately without changing anything.

Canceling the worker is done anyway when the interface goes down
(ieee80211_do_stop).

Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211/mac80211/ath6kl: acquire wdev lock outside ch_switch_notify

The channel switch notification should be sent under the
wdev/sdata-lock, preferably in the same moment as the channel change
happens, to avoid races by other callers (e.g. start/stop_ap).
This also adds the previously missing sdata_lock protection in
csa_finalize_work.

Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: modify beacon using sdata/wdev-lock, not rtnl lock

The csa finalize worker needs to change the beacon information (for
different modes). These are normally protected under rtnl lock, but the
csa finalize worker is called by drivers and should not acquire the RTNL
lock. Therefore change access protection for beacons to sdata/wdev lock.

Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
[fix sdata_dereference]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211: protect beacon changing functions with wdev-lock

To avoid race conditions in functions which modify the beacon
information, lock these using the wdev lock. This is especially required
to avoid problems for csa handling functions which modify beacons but
can not be called under rtnl lock.

Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: mesh: only get tsf if we need it

The local TSF timer is used to compute the timing offset between
mesh peers on beacon reception.  However, asking the device for
the TSF is not very accurate, so we prefer to use rx->mactime
if available.  In the latter case, calling drv_get_tsf() just
adds more delay into the RX path, so skip it if we can.

Signed-off-by: Bob Copeland <bob@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>