Robin Murphy [Wed, 21 Nov 2018 16:00:51 +0000 (16:00 +0000)]
swiotlb: Skip cache maintenance on map error
If swiotlb_bounce_page() failed, calling arch_sync_dma_for_device() may
lead to such delights as performing cache maintenance on whatever
address phys_to_virt(SWIOTLB_MAP_ERROR) looks like, which is typically
outside the kernel memory map and goes about as well as expected.
Don't do that.
Fixes: a4a4330db46a ("swiotlb: add support for non-coherent DMA")
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Robin Murphy [Wed, 21 Nov 2018 16:00:50 +0000 (16:00 +0000)]
dma-direct: Make DIRECT_MAPPING_ERROR viable for SWIOTLB
With the overflow buffer removed, we no longer have a unique address
which is guaranteed not to be a valid DMA target to use as an error
token. The DIRECT_MAPPING_ERROR value of 0 tries to at least represent
an unlikely DMA target, but unfortunately there are already SWIOTLB
users with DMA-able memory at physical address 0 which now gets falsely
treated as a mapping failure and leads to all manner of misbehaviour.
The best we can do to mitigate that is flip DIRECT_MAPPING_ERROR to the
other commonly-used error value of all-bits-set, since the last single
byte of memory is by far the least-likely-valid DMA target.
Fixes: dff8d6c1ed58 ("swiotlb: remove the overflow buffer")
Reported-by: John Stultz <john.stultz@linaro.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Linus Torvalds [Tue, 20 Nov 2018 22:31:00 +0000 (14:31 -0800)]
Merge tag 'mips_fixes_4.20_3' of git://git./linux/kernel/git/mips/linux
Pull MIPS fixes from Paul Burton:
"A few MIPS fixes for 4.20:
- Re-enable the Cavium Octeon USB driver in its defconfig after it
was accidentally removed back in 4.14.
- Have early memblock allocations be performed bottom-up to more
closely match the behaviour we used to have with bootmem, which
seems a safer choice since we've seen fallout from the change made
in the 4.20 merge window.
- Simplify max_low_pfn calculation in the NUMA code for the Loongson3
and SGI IP27 platforms to both clean up the code & ensure
max_low_pfn has been set appropriately before it is used"
* tag 'mips_fixes_4.20_3' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MIPS: Loongson3,SGI-IP27: Simplify max_low_pfn calculation
MIPS: Let early memblock_alloc*() allocate memories bottom-up
MIPS: OCTEON: cavium_octeon_defconfig: re-enable OCTEON USB driver
Linus Torvalds [Tue, 20 Nov 2018 15:37:15 +0000 (07:37 -0800)]
Merge tag 'media/v4.20-3' of git://git./linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
- add a missing include at v4l2-controls uAPI header
- minor kAPI update for the request API
- some fixes at CEC core
- use a lower minimum height for the virtual codec driver
- cleanup a gcc warning due to the lack of a fall though markup
- tc358743: Remove unnecessary self assignment
- fix the V4L event subscription logic
- docs: Document metadata format in struct v4l2_format
- omap3isp and ipu3-cio2: fix unbinding logic
* tag 'media/v4.20-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
media: ipu3-cio2: Use cio2_queues_exit
media: ipu3-cio2: Unregister device nodes first, then release resources
media: omap3isp: Unregister media device as first
media: docs: Document metadata format in struct v4l2_format
media: v4l: event: Add subscription to list before calling "add" operation
media: dm365_ipipeif: better annotate a fall though
media: Rename vb2_m2m_request_queue -> v4l2_m2m_request_queue
media: cec: increase debug level for 'queue full'
media: cec: check for non-OK/NACK conditions while claiming a LA
media: vicodec: lower minimum height to 360
media: tc358743: Remove unnecessary self assignment
media: v4l: fix uapi mpeg slice params definition
v4l2-controls: add a missing include
Linus Torvalds [Mon, 19 Nov 2018 17:24:04 +0000 (09:24 -0800)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
1) Fix some potentially uninitialized variables and use-after-free in
kvaser_usb can drier, from Jimmy Assarsson.
2) Fix leaks in qed driver, from Denis Bolotin.
3) Socket leak in l2tp, from Xin Long.
4) RSS context allocation fix in bnxt_en from Michael Chan.
5) Fix cxgb4 build errors, from Ganesh Goudar.
6) Route leaks in ipv6 when removing exceptions, from Xin Long.
7) Memory leak in IDR allocation handling of act_pedit, from Davide
Caratti.
8) Use-after-free of bridge vlan stats, from Nikolay Aleksandrov.
9) When MTU is locked, do not force DF bit on ipv4 tunnels. From
Sabrina Dubroca.
10) When NAPI cached skb is reused, we must set it to the proper initial
state which includes skb->pkt_type. From Eric Dumazet.
11) Lockdep and non-linear SKB handling fix in tipc from Jon Maloy.
12) Set RX queue properly in various tuntap receive paths, from Matthew
Cover.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (61 commits)
tuntap: fix multiqueue rx
ipv6: Fix PMTU updates for UDP/raw sockets in presence of VRF
tipc: don't assume linear buffer when reading ancillary data
tipc: fix lockdep warning when reinitilaizing sockets
net-gro: reset skb->pkt_type in napi_reuse_skb()
tc-testing: tdc.py: Guard against lack of returncode in executed command
tc-testing: tdc.py: ignore errors when decoding stdout/stderr
ip_tunnel: don't force DF when MTU is locked
MAINTAINERS: Add entry for CAKE qdisc
net: bridge: fix vlan stats use-after-free on destruction
socket: do a generic_file_splice_read when proto_ops has no splice_read
net: phy: mdio-gpio: Fix working over slow can_sleep GPIOs
Revert "net: phy: mdio-gpio: Fix working over slow can_sleep GPIOs"
net: phy: mdio-gpio: Fix working over slow can_sleep GPIOs
net/sched: act_pedit: fix memory leak when IDR allocation fails
net: lantiq: Fix returned value in case of error in 'xrx200_probe()'
ipv6: fix a dst leak when removing its exception
net: mvneta: Don't advertise 2.5G modes
drivers/net/ethernet/qlogic/qed/qed_rdma.h: fix typo
net/mlx4: Fix UBSAN warning of signed integer overflow
...
Matthew Cover [Sun, 18 Nov 2018 07:46:00 +0000 (00:46 -0700)]
tuntap: fix multiqueue rx
When writing packets to a descriptor associated with a combined queue, the
packets should end up on that queue.
Before this change all packets written to any descriptor associated with a
tap interface end up on rx-0, even when the descriptor is associated with a
different queue.
The rx traffic can be generated by either of the following.
1. a simple tap program which spins up multiple queues and writes packets
to each of the file descriptors
2. tx from a qemu vm with a tap multiqueue netdev
The queue for rx traffic can be observed by either of the following (done
on the hypervisor in the qemu case).
1. a simple netmap program which opens and reads from per-queue
descriptors
2. configuring RPS and doing per-cpu captures with rxtxcpu
Alternatively, if you printk() the return value of skb_get_rx_queue() just
before each instance of netif_receive_skb() in tun.c, you will get 65535
for every skb.
Calling skb_record_rx_queue() to set the rx queue to the queue_index fixes
the association between descriptor and rx queue.
Signed-off-by: Matthew Cover <matthew.cover@stackpath.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Sun, 18 Nov 2018 18:45:30 +0000 (10:45 -0800)]
ipv6: Fix PMTU updates for UDP/raw sockets in presence of VRF
Preethi reported that PMTU discovery for UDP/raw applications is not
working in the presence of VRF when the socket is not bound to a device.
The problem is that ip6_sk_update_pmtu does not consider the L3 domain
of the skb device if the socket is not bound. Update the function to
set oif to the L3 master device if relevant.
Fixes: ca254490c8df ("net: Add VRF support to IPv6 stack")
Reported-by: Preethi Ramachandra <preethir@juniper.net>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 18 Nov 2018 21:33:44 +0000 (13:33 -0800)]
Linux 4.20-rc3
Linus Torvalds [Sun, 18 Nov 2018 20:21:09 +0000 (12:21 -0800)]
Merge tag 'libnvdimm-fixes-4.20-rc3' of git://git./linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dan Williams:
"A small batch of fixes for v4.20-rc3.
The overflow continuation fix addresses something that has been broken
for several releases. Arguably it could wait even longer, but it's a
one line fix and this finishes the last of the known address range
scrub bug reports. The revert addresses a lockdep regression. The unit
tests are not critical to fix, but no reason to hold this fix back.
Summary:
- Address Range Scrub overflow continuation handling has been broken
since it was initially merged. It was only recently that error
injection and platform-BIOS support enabled this corner case to be
exercised.
- The recent attempt to provide more isolation for the kernel Address
Range Scrub state machine from userapace initiated sessions
triggers a lockdep report. Revert and try again at the next merge
window.
- Fix a kasan reported buffer overflow in libnvdimm unit test
infrastrucutre (nfit_test)"
* tag 'libnvdimm-fixes-4.20-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
Revert "acpi, nfit: Further restrict userspace ARS start requests"
acpi, nfit: Fix ARS overflow continuation
tools/testing/nvdimm: Fix the array size for dimm devices.
Linus Torvalds [Sun, 18 Nov 2018 19:31:26 +0000 (11:31 -0800)]
Merge branch 'akpm' (patches from Andrew)
Merge misc fixes from Andrew Morton:
"16 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm/memblock.c: fix a typo in __next_mem_pfn_range() comments
mm, page_alloc: check for max order in hot path
scripts/spdxcheck.py: make python3 compliant
tmpfs: make lseek(SEEK_DATA/SEK_HOLE) return ENXIO with a negative offset
lib/ubsan.c: don't mark __ubsan_handle_builtin_unreachable as noreturn
mm/vmstat.c: fix NUMA statistics updates
mm/gup.c: fix follow_page_mask() kerneldoc comment
ocfs2: free up write context when direct IO failed
scripts/faddr2line: fix location of start_kernel in comment
mm: don't reclaim inodes with many attached pages
mm, memory_hotplug: check zone_movable in has_unmovable_pages
mm/swapfile.c: use kvzalloc for swap_info_struct allocation
MAINTAINERS: update OMAP MMC entry
hugetlbfs: fix kernel BUG at fs/hugetlbfs/inode.c:444!
kernel/sched/psi.c: simplify cgroup_move_task()
z3fold: fix possible reclaim races
Linus Torvalds [Sun, 18 Nov 2018 18:58:20 +0000 (10:58 -0800)]
Merge branch 'sched-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull scheduler fix from Ingo Molnar:
"Fix an exec() related scalability/performance regression, which was
caused by incorrectly calculating load and migrating tasks on exec()
when they shouldn't be"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/fair: Fix cpu_util_wake() for 'execl' type workloads
Linus Torvalds [Sun, 18 Nov 2018 18:54:59 +0000 (10:54 -0800)]
Merge branch 'perf-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Fix uncore PMU enumeration for CofeeLake CPUs"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel/uncore: Support CoffeeLake 8th CBOX
perf/x86/intel/uncore: Add more IMC PCI IDs for KabyLake and CoffeeLake CPUs
Linus Torvalds [Sun, 18 Nov 2018 18:52:26 +0000 (10:52 -0800)]
Merge branch 'efi-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull EFI fixes from Ingo Molnar:
"Misc fixes: two warning splat fixes, a leak fix and persistent memory
allocation fixes for ARM"
* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi: Permit calling efi_mem_reserve_persistent() from atomic context
efi/arm: Defer persistent reservations until after paging_init()
efi/arm/libstub: Pack FDT after populating it
efi/arm: Revert deferred unmap of early memmap mapping
efi: Fix debugobjects warning on 'efi_rts_work'
Linus Torvalds [Sun, 18 Nov 2018 18:45:09 +0000 (10:45 -0800)]
Merge branch 'spectre' of git://git.armlinux.org.uk/~rmk/linux-arm
Pull ARM spectre updates from Russell King:
"These are the currently known final bits that resolve the Spectre
issues. big.Little systems used to be sufficiently identical in that
there were no differences between individual CPUs in the system that
mattered to the kernel. With the advent of the Spectre problem, the
CPUs now have differences in how the workaround is applied.
As a result of previous Spectre patches, these systems ended up
reporting quite a lot of:
"CPUx: Spectre v2: incorrect context switching function, system vulnerable"
messages due to the action of the big.Little switcher causing the CPUs
to be re-initialised regularly. This series resolves that issue by
making the CPU vtable unique to each CPU.
However, since this is used very early, before per-cpu is setup,
per-cpu can't be used. We also have a problem that two of the methods
are not called from preempt-safe paths, but thankfully these remain
identical between all CPUs in the system. To make sure, we validate
that these are identical during boot"
* 'spectre' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: spectre-v2: per-CPU vtables to work around big.Little systems
ARM: add PROC_VTABLE and PROC_TABLE macros
ARM: clean up per-processor check_bugs method call
ARM: split out processor lookup
ARM: make lookup_processor_type() non-__init
Chen Chang [Fri, 16 Nov 2018 23:08:57 +0000 (15:08 -0800)]
mm/memblock.c: fix a typo in __next_mem_pfn_range() comments
Link: http://lkml.kernel.org/r/20181107100247.13359-1-rainccrun@gmail.com
Signed-off-by: Chen Chang <rainccrun@gmail.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Mike Rapoport <rppt@linux.ibm.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michal Hocko [Fri, 16 Nov 2018 23:08:53 +0000 (15:08 -0800)]
mm, page_alloc: check for max order in hot path
Konstantin has noticed that kvmalloc might trigger the following
warning:
WARNING: CPU: 0 PID: 6676 at mm/vmstat.c:986 __fragmentation_index+0x54/0x60
[...]
Call Trace:
fragmentation_index+0x76/0x90
compaction_suitable+0x4f/0xf0
shrink_node+0x295/0x310
node_reclaim+0x205/0x250
get_page_from_freelist+0x649/0xad0
__alloc_pages_nodemask+0x12a/0x2a0
kmalloc_large_node+0x47/0x90
__kmalloc_node+0x22b/0x2e0
kvmalloc_node+0x3e/0x70
xt_alloc_table_info+0x3a/0x80 [x_tables]
do_ip6t_set_ctl+0xcd/0x1c0 [ip6_tables]
nf_setsockopt+0x44/0x60
SyS_setsockopt+0x6f/0xc0
do_syscall_64+0x67/0x120
entry_SYSCALL_64_after_hwframe+0x3d/0xa2
the problem is that we only check for an out of bound order in the slow
path and the node reclaim might happen from the fast path already. This
is fixable by making sure that kvmalloc doesn't ever use kmalloc for
requests that are larger than KMALLOC_MAX_SIZE but this also shows that
the code is rather fragile. A recent UBSAN report just underlines that
by the following report
UBSAN: Undefined behaviour in mm/page_alloc.c:3117:19
shift exponent 51 is too large for 32-bit type 'int'
CPU: 0 PID: 6520 Comm: syz-executor1 Not tainted 4.19.0-rc2 #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0xd2/0x148 lib/dump_stack.c:113
ubsan_epilogue+0x12/0x94 lib/ubsan.c:159
__ubsan_handle_shift_out_of_bounds+0x2b6/0x30b lib/ubsan.c:425
__zone_watermark_ok+0x2c7/0x400 mm/page_alloc.c:3117
zone_watermark_fast mm/page_alloc.c:3216 [inline]
get_page_from_freelist+0xc49/0x44c0 mm/page_alloc.c:3300
__alloc_pages_nodemask+0x21e/0x640 mm/page_alloc.c:4370
alloc_pages_current+0xcc/0x210 mm/mempolicy.c:2093
alloc_pages include/linux/gfp.h:509 [inline]
__get_free_pages+0x12/0x60 mm/page_alloc.c:4414
dma_mem_alloc+0x36/0x50 arch/x86/include/asm/floppy.h:156
raw_cmd_copyin drivers/block/floppy.c:3159 [inline]
raw_cmd_ioctl drivers/block/floppy.c:3206 [inline]
fd_locked_ioctl+0xa00/0x2c10 drivers/block/floppy.c:3544
fd_ioctl+0x40/0x60 drivers/block/floppy.c:3571
__blkdev_driver_ioctl block/ioctl.c:303 [inline]
blkdev_ioctl+0xb3c/0x1a30 block/ioctl.c:601
block_ioctl+0x105/0x150 fs/block_dev.c:1883
vfs_ioctl fs/ioctl.c:46 [inline]
do_vfs_ioctl+0x1c0/0x1150 fs/ioctl.c:687
ksys_ioctl+0x9e/0xb0 fs/ioctl.c:702
__do_sys_ioctl fs/ioctl.c:709 [inline]
__se_sys_ioctl fs/ioctl.c:707 [inline]
__x64_sys_ioctl+0x7e/0xc0 fs/ioctl.c:707
do_syscall_64+0xc4/0x510 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Note that this is not a kvmalloc path. It is just that the fast path
really depends on having sanitzed order as well. Therefore move the
order check to the fast path.
Link: http://lkml.kernel.org/r/20181113094305.GM15120@dhcp22.suse.cz
Signed-off-by: Michal Hocko <mhocko@suse.com>
Reported-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Reported-by: Kyungtae Kim <kt0755@gmail.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Balbir Singh <bsingharora@gmail.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Pavel Tatashin <pavel.tatashin@microsoft.com>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Aaron Lu <aaron.lu@intel.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Byoungyoung Lee <lifeasageek@gmail.com>
Cc: "Dae R. Jeong" <threeearcat@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Uwe Kleine-König [Fri, 16 Nov 2018 23:08:43 +0000 (15:08 -0800)]
scripts/spdxcheck.py: make python3 compliant
Without this change the following happens when using Python3 (3.6.6):
$ echo "GPL-2.0" | python3 scripts/spdxcheck.py -
FAIL: 'str' object has no attribute 'decode'
Traceback (most recent call last):
File "scripts/spdxcheck.py", line 253, in <module>
parser.parse_lines(sys.stdin, args.maxlines, '-')
File "scripts/spdxcheck.py", line 171, in parse_lines
line = line.decode(locale.getpreferredencoding(False), errors='ignore')
AttributeError: 'str' object has no attribute 'decode'
So as the line is already a string, there is no need to decode it and
the line can be dropped.
/usr/bin/python on Arch is Python 3. So this would indeed be worth
going into 4.19.
Link: http://lkml.kernel.org/r/20181023070802.22558-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Joe Perches <joe@perches.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Yufen Yu [Fri, 16 Nov 2018 23:08:39 +0000 (15:08 -0800)]
tmpfs: make lseek(SEEK_DATA/SEK_HOLE) return ENXIO with a negative offset
Other filesystems such as ext4, f2fs and ubifs all return ENXIO when
lseek (SEEK_DATA or SEEK_HOLE) requests a negative offset.
man 2 lseek says
: EINVAL whence is not valid. Or: the resulting file offset would be
: negative, or beyond the end of a seekable device.
:
: ENXIO whence is SEEK_DATA or SEEK_HOLE, and the file offset is beyond
: the end of the file.
Make tmpfs return ENXIO under these circumstances as well. After this,
tmpfs also passes xfstests's generic/448.
[akpm@linux-foundation.org: rewrite changelog]
Link: http://lkml.kernel.org/r/1540434176-14349-1-git-send-email-yuyufen@huawei.com
Signed-off-by: Yufen Yu <yuyufen@huawei.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Hugh Dickins <hughd@google.com>
Cc: William Kucharski <william.kucharski@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Arnd Bergmann [Fri, 16 Nov 2018 23:08:35 +0000 (15:08 -0800)]
lib/ubsan.c: don't mark __ubsan_handle_builtin_unreachable as noreturn
gcc-8 complains about the prototype for this function:
lib/ubsan.c:432:1: error: ignoring attribute 'noreturn' in declaration of a built-in function '__ubsan_handle_builtin_unreachable' because it conflicts with attribute 'const' [-Werror=attributes]
This is actually a GCC's bug. In GCC internals
__ubsan_handle_builtin_unreachable() declared with both 'noreturn' and
'const' attributes instead of only 'noreturn':
https://gcc.gnu.org/bugzilla/show_bug.cgi?id=84210
Workaround this by removing the noreturn attribute.
[aryabinin: add information about GCC bug in changelog]
Link: http://lkml.kernel.org/r/20181107144516.4587-1-aryabinin@virtuozzo.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Acked-by: Olof Johansson <olof@lixom.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Janne Huttunen [Fri, 16 Nov 2018 23:08:32 +0000 (15:08 -0800)]
mm/vmstat.c: fix NUMA statistics updates
Scan through the whole array to see if an update is needed. While we're
at it, use sizeof() to be safe against any possible type changes in the
future.
The bug here is that we wouldn't sync per-cpu counters into global ones
if there was an update of numa_stats for higher cpus. Highly
theoretical one though because it is much more probable that zone_stats
are updated so we would refresh anyway. So I wouldn't bother to mark
this for stable, yet something nice to fix.
[mhocko@suse.com: changelog enhancement]
Link: http://lkml.kernel.org/r/1541601517-17282-1-git-send-email-janne.huttunen@nokia.com
Fixes: 1d90ca897cb0 ("mm: update NUMA counter threshold size")
Signed-off-by: Janne Huttunen <janne.huttunen@nokia.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mike Rapoport [Fri, 16 Nov 2018 23:08:29 +0000 (15:08 -0800)]
mm/gup.c: fix follow_page_mask() kerneldoc comment
Commit
df06b37ffe5a ("mm/gup: cache dev_pagemap while pinning pages")
modified the signature of follow_page_mask() but left the parameter
description behind.
Update the description to make the code and comments agree again.
While at it, update formatting of the return value description to match
Documentation/doc-guide/kernel-doc.rst guidelines.
Link: http://lkml.kernel.org/r/1541603316-27832-1-git-send-email-rppt@linux.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Wengang Wang [Fri, 16 Nov 2018 23:08:25 +0000 (15:08 -0800)]
ocfs2: free up write context when direct IO failed
The write context should also be freed even when direct IO failed.
Otherwise a memory leak is introduced and entries remain in
oi->ip_unwritten_list causing the following BUG later in unlink path:
ERROR: bug expression: !list_empty(&oi->ip_unwritten_list)
ERROR: Clear inode of 215043, inode has unwritten extents
...
Call Trace:
? __set_current_blocked+0x42/0x68
ocfs2_evict_inode+0x91/0x6a0 [ocfs2]
? bit_waitqueue+0x40/0x33
evict+0xdb/0x1af
iput+0x1a2/0x1f7
do_unlinkat+0x194/0x28f
SyS_unlinkat+0x1b/0x2f
do_syscall_64+0x79/0x1ae
entry_SYSCALL_64_after_hwframe+0x151/0x0
This patch also logs, with frequency limit, direct IO failures.
Link: http://lkml.kernel.org/r/20181102170632.25921-1-wen.gang.wang@oracle.com
Signed-off-by: Wengang Wang <wen.gang.wang@oracle.com>
Reviewed-by: Junxiao Bi <junxiao.bi@oracle.com>
Reviewed-by: Changwei Ge <ge.changwei@h3c.com>
Reviewed-by: Joseph Qi <jiangqi903@gmail.com>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Randy Dunlap [Fri, 16 Nov 2018 23:08:22 +0000 (15:08 -0800)]
scripts/faddr2line: fix location of start_kernel in comment
Fix a source file reference location to the correct path name.
Link: http://lkml.kernel.org/r/1d50bd3d-178e-dcd8-779f-9711887440eb@infradead.org
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Roman Gushchin [Fri, 16 Nov 2018 23:08:18 +0000 (15:08 -0800)]
mm: don't reclaim inodes with many attached pages
Spock reported that commit
172b06c32b94 ("mm: slowly shrink slabs with a
relatively small number of objects") leads to a regression on his setup:
periodically the majority of the pagecache is evicted without an obvious
reason, while before the change the amount of free memory was balancing
around the watermark.
The reason behind is that the mentioned above change created some
minimal background pressure on the inode cache. The problem is that if
an inode is considered to be reclaimed, all belonging pagecache page are
stripped, no matter how many of them are there. So, if a huge
multi-gigabyte file is cached in the memory, and the goal is to reclaim
only few slab objects (unused inodes), we still can eventually evict all
gigabytes of the pagecache at once.
The workload described by Spock has few large non-mapped files in the
pagecache, so it's especially noticeable.
To solve the problem let's postpone the reclaim of inodes, which have
more than 1 attached page. Let's wait until the pagecache pages will be
evicted naturally by scanning the corresponding LRU lists, and only then
reclaim the inode structure.
Link: http://lkml.kernel.org/r/20181023164302.20436-1-guro@fb.com
Signed-off-by: Roman Gushchin <guro@fb.com>
Reported-by: Spock <dairinin@gmail.com>
Tested-by: Spock <dairinin@gmail.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Rik van Riel <riel@surriel.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: <stable@vger.kernel.org> [4.19.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michal Hocko [Fri, 16 Nov 2018 23:08:15 +0000 (15:08 -0800)]
mm, memory_hotplug: check zone_movable in has_unmovable_pages
Page state checks are racy. Under a heavy memory workload (e.g. stress
-m 200 -t 2h) it is quite easy to hit a race window when the page is
allocated but its state is not fully populated yet. A debugging patch to
dump the struct page state shows
has_unmovable_pages: pfn:0x10dfec00, found:0x1, count:0x0
page:
ffffea0437fb0000 count:1 mapcount:1 mapping:
ffff880e05239841 index:0x7f26e5000 compound_mapcount: 1
flags: 0x5fffffc0090034(uptodate|lru|active|head|swapbacked)
Note that the state has been checked for both PageLRU and PageSwapBacked
already. Closing this race completely would require some sort of retry
logic. This can be tricky and error prone (think of potential endless
or long taking loops).
Workaround this problem for movable zones at least. Such a zone should
only contain movable pages. Commit
15c30bc09085 ("mm, memory_hotplug:
make has_unmovable_pages more robust") has told us that this is not
strictly true though. Bootmem pages should be marked reserved though so
we can move the original check after the PageReserved check. Pages from
other zones are still prone to races but we even do not pretend that
memory hotremove works for those so pre-mature failure doesn't hurt that
much.
Link: http://lkml.kernel.org/r/20181106095524.14629-1-mhocko@kernel.org
Fixes: 15c30bc09085 ("mm, memory_hotplug: make has_unmovable_pages more robust")
Signed-off-by: Michal Hocko <mhocko@suse.com>
Reported-by: Baoquan He <bhe@redhat.com>
Tested-by: Baoquan He <bhe@redhat.com>
Acked-by: Baoquan He <bhe@redhat.com>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Vasily Averin [Fri, 16 Nov 2018 23:08:11 +0000 (15:08 -0800)]
mm/swapfile.c: use kvzalloc for swap_info_struct allocation
Commit
a2468cc9bfdf ("swap: choose swap device according to numa node")
changed 'avail_lists' field of 'struct swap_info_struct' to an array.
In popular linux distros it increased size of swap_info_struct up to 40
Kbytes and now swap_info_struct allocation requires order-4 page.
Switch to kvzmalloc allows to avoid unexpected allocation failures.
Link: http://lkml.kernel.org/r/fc23172d-3c75-21e2-d551-8b1808cbe593@virtuozzo.com
Fixes: a2468cc9bfdf ("swap: choose swap device according to numa node")
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Acked-by: Aaron Lu <aaron.lu@intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Huang Ying <ying.huang@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Aaro Koskinen [Fri, 16 Nov 2018 23:08:08 +0000 (15:08 -0800)]
MAINTAINERS: update OMAP MMC entry
Jarkko's e-mail address hasn't worked for a long time. We still want to
keep this driver working as it is critical for some of the OMAP boards.
I use and test this driver frequently, so change myself as a maintainer
with "Odd Fixes" status.
Link: http://lkml.kernel.org/r/20181106222750.12939-1-aaro.koskinen@iki.fi
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mike Kravetz [Fri, 16 Nov 2018 23:08:04 +0000 (15:08 -0800)]
hugetlbfs: fix kernel BUG at fs/hugetlbfs/inode.c:444!
This bug has been experienced several times by the Oracle DB team. The
BUG is in remove_inode_hugepages() as follows:
/*
* If page is mapped, it was faulted in after being
* unmapped in caller. Unmap (again) now after taking
* the fault mutex. The mutex will prevent faults
* until we finish removing the page.
*
* This race can only happen in the hole punch case.
* Getting here in a truncate operation is a bug.
*/
if (unlikely(page_mapped(page))) {
BUG_ON(truncate_op);
In this case, the elevated map count is not the result of a race.
Rather it was incorrectly incremented as the result of a bug in the huge
pmd sharing code. Consider the following:
- Process A maps a hugetlbfs file of sufficient size and alignment
(PUD_SIZE) that a pmd page could be shared.
- Process B maps the same hugetlbfs file with the same size and
alignment such that a pmd page is shared.
- Process B then calls mprotect() to change protections for the mapping
with the shared pmd. As a result, the pmd is 'unshared'.
- Process B then calls mprotect() again to chage protections for the
mapping back to their original value. pmd remains unshared.
- Process B then forks and process C is created. During the fork
process, we do dup_mm -> dup_mmap -> copy_page_range to copy page
tables. Copying page tables for hugetlb mappings is done in the
routine copy_hugetlb_page_range.
In copy_hugetlb_page_range(), the destination pte is obtained by:
dst_pte = huge_pte_alloc(dst, addr, sz);
If pmd sharing is possible, the returned pointer will be to a pte in an
existing page table. In the situation above, process C could share with
either process A or process B. Since process A is first in the list,
the returned pte is a pointer to a pte in process A's page table.
However, the check for pmd sharing in copy_hugetlb_page_range is:
/* If the pagetables are shared don't copy or take references */
if (dst_pte == src_pte)
continue;
Since process C is sharing with process A instead of process B, the
above test fails. The code in copy_hugetlb_page_range which follows
assumes dst_pte points to a huge_pte_none pte. It copies the pte entry
from src_pte to dst_pte and increments this map count of the associated
page. This is how we end up with an elevated map count.
To solve, check the dst_pte entry for huge_pte_none. If !none, this
implies PMD sharing so do not copy.
Link: http://lkml.kernel.org/r/20181105212315.14125-1-mike.kravetz@oracle.com
Fixes: c5c99429fa57 ("fix hugepages leak due to pagetable page sharing")
Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com>
Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: "Kirill A . Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Prakash Sangappa <prakash.sangappa@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Olof Johansson [Fri, 16 Nov 2018 23:08:00 +0000 (15:08 -0800)]
kernel/sched/psi.c: simplify cgroup_move_task()
The existing code triggered an invalid warning about 'rq' possibly being
used uninitialized. Instead of doing the silly warning suppression by
initializa it to NULL, refactor the code to bail out early instead.
Warning was:
kernel/sched/psi.c: In function `cgroup_move_task':
kernel/sched/psi.c:639:13: warning: `rq' may be used uninitialized in this function [-Wmaybe-uninitialized]
Link: http://lkml.kernel.org/r/20181103183339.8669-1-olof@lixom.net
Fixes: 2ce7135adc9ad ("psi: cgroup support")
Signed-off-by: Olof Johansson <olof@lixom.net>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Vitaly Wool [Fri, 16 Nov 2018 23:07:56 +0000 (15:07 -0800)]
z3fold: fix possible reclaim races
Reclaim and free can race on an object which is basically fine but in
order for reclaim to be able to map "freed" object we need to encode
object length in the handle. handle_to_chunks() is then introduced to
extract object length from a handle and use it during mapping.
Moreover, to avoid racing on a z3fold "headless" page release, we should
not try to free that page in z3fold_free() if the reclaim bit is set.
Also, in the unlikely case of trying to reclaim a page being freed, we
should not proceed with that page.
While at it, fix the page accounting in reclaim function.
This patch supersedes "[PATCH] z3fold: fix reclaim lock-ups".
Link: http://lkml.kernel.org/r/20181105162225.74e8837d03583a9b707cf559@gmail.com
Signed-off-by: Vitaly Wool <vitaly.vul@sony.com>
Signed-off-by: Jongseok Kim <ks77sj@gmail.com>
Reported-by-by: Jongseok Kim <ks77sj@gmail.com>
Reviewed-by: Snild Dolkow <snild@sony.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jon Maloy [Sat, 17 Nov 2018 17:17:06 +0000 (12:17 -0500)]
tipc: don't assume linear buffer when reading ancillary data
The code for reading ancillary data from a received buffer is assuming
the buffer is linear. To make this assumption true we have to linearize
the buffer before message data is read.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Maloy [Fri, 16 Nov 2018 21:55:04 +0000 (16:55 -0500)]
tipc: fix lockdep warning when reinitilaizing sockets
We get the following warning:
[ 47.926140] 32-bit node address hash set to
2010a0a
[ 47.927202]
[ 47.927433] ================================
[ 47.928050] WARNING: inconsistent lock state
[ 47.928661] 4.19.0+ #37 Tainted: G E
[ 47.929346] --------------------------------
[ 47.929954] inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage.
[ 47.930116] swapper/3/0 [HC0[0]:SC1[3]:HE1:SE0] takes:
[ 47.930116]
00000000af8bc31e (&(&ht->lock)->rlock){+.?.}, at: rhashtable_walk_enter+0x36/0xb0
[ 47.930116] {SOFTIRQ-ON-W} state was registered at:
[ 47.930116] _raw_spin_lock+0x29/0x60
[ 47.930116] rht_deferred_worker+0x556/0x810
[ 47.930116] process_one_work+0x1f5/0x540
[ 47.930116] worker_thread+0x64/0x3e0
[ 47.930116] kthread+0x112/0x150
[ 47.930116] ret_from_fork+0x3a/0x50
[ 47.930116] irq event stamp: 14044
[ 47.930116] hardirqs last enabled at (14044): [<
ffffffff9a07fbba>] __local_bh_enable_ip+0x7a/0xf0
[ 47.938117] hardirqs last disabled at (14043): [<
ffffffff9a07fb81>] __local_bh_enable_ip+0x41/0xf0
[ 47.938117] softirqs last enabled at (14028): [<
ffffffff9a0803ee>] irq_enter+0x5e/0x60
[ 47.938117] softirqs last disabled at (14029): [<
ffffffff9a0804a5>] irq_exit+0xb5/0xc0
[ 47.938117]
[ 47.938117] other info that might help us debug this:
[ 47.938117] Possible unsafe locking scenario:
[ 47.938117]
[ 47.938117] CPU0
[ 47.938117] ----
[ 47.938117] lock(&(&ht->lock)->rlock);
[ 47.938117] <Interrupt>
[ 47.938117] lock(&(&ht->lock)->rlock);
[ 47.938117]
[ 47.938117] *** DEADLOCK ***
[ 47.938117]
[ 47.938117] 2 locks held by swapper/3/0:
[ 47.938117] #0:
0000000062c64f90 ((&d->timer)){+.-.}, at: call_timer_fn+0x5/0x280
[ 47.938117] #1:
00000000ee39619c (&(&d->lock)->rlock){+.-.}, at: tipc_disc_timeout+0xc8/0x540 [tipc]
[ 47.938117]
[ 47.938117] stack backtrace:
[ 47.938117] CPU: 3 PID: 0 Comm: swapper/3 Tainted: G E 4.19.0+ #37
[ 47.938117] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
[ 47.938117] Call Trace:
[ 47.938117] <IRQ>
[ 47.938117] dump_stack+0x5e/0x8b
[ 47.938117] print_usage_bug+0x1ed/0x1ff
[ 47.938117] mark_lock+0x5b5/0x630
[ 47.938117] __lock_acquire+0x4c0/0x18f0
[ 47.938117] ? lock_acquire+0xa6/0x180
[ 47.938117] lock_acquire+0xa6/0x180
[ 47.938117] ? rhashtable_walk_enter+0x36/0xb0
[ 47.938117] _raw_spin_lock+0x29/0x60
[ 47.938117] ? rhashtable_walk_enter+0x36/0xb0
[ 47.938117] rhashtable_walk_enter+0x36/0xb0
[ 47.938117] tipc_sk_reinit+0xb0/0x410 [tipc]
[ 47.938117] ? mark_held_locks+0x6f/0x90
[ 47.938117] ? __local_bh_enable_ip+0x7a/0xf0
[ 47.938117] ? lockdep_hardirqs_on+0x20/0x1a0
[ 47.938117] tipc_net_finalize+0xbf/0x180 [tipc]
[ 47.938117] tipc_disc_timeout+0x509/0x540 [tipc]
[ 47.938117] ? call_timer_fn+0x5/0x280
[ 47.938117] ? tipc_disc_msg_xmit.isra.19+0xa0/0xa0 [tipc]
[ 47.938117] ? tipc_disc_msg_xmit.isra.19+0xa0/0xa0 [tipc]
[ 47.938117] call_timer_fn+0xa1/0x280
[ 47.938117] ? tipc_disc_msg_xmit.isra.19+0xa0/0xa0 [tipc]
[ 47.938117] run_timer_softirq+0x1f2/0x4d0
[ 47.938117] __do_softirq+0xfc/0x413
[ 47.938117] irq_exit+0xb5/0xc0
[ 47.938117] smp_apic_timer_interrupt+0xac/0x210
[ 47.938117] apic_timer_interrupt+0xf/0x20
[ 47.938117] </IRQ>
[ 47.938117] RIP: 0010:default_idle+0x1c/0x140
[ 47.938117] Code: 90 90 90 90 90 90 90 90 90 90 90 90 90 90 0f 1f 44 00 00 41 54 55 53 65 8b 2d d8 2b 74 65 0f 1f 44 00 00 e8 c6 2c 8b ff fb f4 <65> 8b 2d c5 2b 74 65 0f 1f 44 00 00 5b 5d 41 5c c3 65 8b 05 b4 2b
[ 47.938117] RSP: 0018:
ffffaf6ac0207ec8 EFLAGS:
00000206 ORIG_RAX:
ffffffffffffff13
[ 47.938117] RAX:
ffff8f5b3735e200 RBX:
0000000000000003 RCX:
0000000000000001
[ 47.938117] RDX:
0000000000000001 RSI:
0000000000000001 RDI:
ffff8f5b3735e200
[ 47.938117] RBP:
0000000000000003 R08:
0000000000000001 R09:
0000000000000000
[ 47.938117] R10:
0000000000000000 R11:
0000000000000000 R12:
0000000000000000
[ 47.938117] R13:
0000000000000000 R14:
ffff8f5b3735e200 R15:
ffff8f5b3735e200
[ 47.938117] ? default_idle+0x1a/0x140
[ 47.938117] do_idle+0x1bc/0x280
[ 47.938117] cpu_startup_entry+0x19/0x20
[ 47.938117] start_secondary+0x187/0x1c0
[ 47.938117] secondary_startup_64+0xa4/0xb0
The reason seems to be that tipc_net_finalize()->tipc_sk_reinit() is
calling the function rhashtable_walk_enter() within a timer interrupt.
We fix this by executing tipc_net_finalize() in work queue context.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sun, 18 Nov 2018 05:57:02 +0000 (21:57 -0800)]
net-gro: reset skb->pkt_type in napi_reuse_skb()
eth_type_trans() assumes initial value for skb->pkt_type
is PACKET_HOST.
This is indeed the value right after a fresh skb allocation.
However, it is possible that GRO merged a packet with a different
value (like PACKET_OTHERHOST in case macvlan is used), so
we need to make sure napi->skb will have pkt_type set back to
PACKET_HOST.
Otherwise, valid packets might be dropped by the stack because
their pkt_type is not PACKET_HOST.
napi_reuse_skb() was added in commit
96e93eab2033 ("gro: Add
internal interfaces for VLAN"), but this bug always has
been there.
Fixes: 96e93eab2033 ("gro: Add internal interfaces for VLAN")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 18 Nov 2018 05:54:53 +0000 (21:54 -0800)]
Merge branch 'tdc-fixes'
Lucas Bates says:
====================
Prevent uncaught exceptions in tdc
This patch series addresses two potential bugs in tdc that can
cause exceptions to be raised in certain circumstances. These
exceptions are generally not handled, so instead we will prevent
them from being raised.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Brenda J. Butler [Fri, 16 Nov 2018 22:37:56 +0000 (17:37 -0500)]
tc-testing: tdc.py: Guard against lack of returncode in executed command
Add some defensive coding in case one of the subprocesses created by tdc
returns nothing. If no object is returned from exec_cmd, then tdc will
halt with an unhandled exception.
Signed-off-by: Brenda J. Butler <bjb@mojatatu.com>
Signed-off-by: Lucas Bates <lucasb@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lucas Bates [Fri, 16 Nov 2018 22:37:55 +0000 (17:37 -0500)]
tc-testing: tdc.py: ignore errors when decoding stdout/stderr
Prevent exceptions from being raised while decoding output
from an executed command. There is no impact on tdc's
execution and the verify command phase would fail the pattern
match.
Signed-off-by: Lucas Bates <lucasb@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sabrina Dubroca [Fri, 16 Nov 2018 15:58:19 +0000 (16:58 +0100)]
ip_tunnel: don't force DF when MTU is locked
The various types of tunnels running over IPv4 can ask to set the DF
bit to do PMTU discovery. However, PMTU discovery is subject to the
threshold set by the net.ipv4.route.min_pmtu sysctl, and is also
disabled on routes with "mtu lock". In those cases, we shouldn't set
the DF bit.
This patch makes setting the DF bit conditional on the route's MTU
locking state.
This issue seems to be older than git history.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Toke Høiland-Jørgensen [Fri, 16 Nov 2018 20:13:59 +0000 (12:13 -0800)]
MAINTAINERS: Add entry for CAKE qdisc
We would like the existing community to be kept in the loop for any new
developments on CAKE; and I certainly plan to keep maintaining it. Reflect
this in MAINTAINERS.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov [Fri, 16 Nov 2018 16:50:01 +0000 (18:50 +0200)]
net: bridge: fix vlan stats use-after-free on destruction
Syzbot reported a use-after-free of the global vlan context on port vlan
destruction. When I added per-port vlan stats I missed the fact that the
global vlan context can be freed before the per-port vlan rcu callback.
There're a few different ways to deal with this, I've chosen to add a
new private flag that is set only when per-port stats are allocated so
we can directly check it on destruction without dereferencing the global
context at all. The new field in net_bridge_vlan uses a hole.
v2: cosmetic change, move the check to br_process_vlan_info where the
other checks are done
v3: add change log in the patch, add private (in-kernel only) flags in a
hole in net_bridge_vlan struct and use that instead of mixing
user-space flags with private flags
Fixes: 9163a0fc1f0c ("net: bridge: add support for per-port vlan stats")
Reported-by: syzbot+04681da557a0e49a52e5@syzkaller.appspotmail.com
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Slavomir Kaslev [Fri, 16 Nov 2018 09:27:53 +0000 (11:27 +0200)]
socket: do a generic_file_splice_read when proto_ops has no splice_read
splice(2) fails with -EINVAL when called reading on a socket with no splice_read
set in its proto_ops (such as vsock sockets). Switch this to fallbacks to a
generic_file_splice_read instead.
Signed-off-by: Slavomir Kaslev <kaslevs@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Martin Schiller [Fri, 16 Nov 2018 07:38:36 +0000 (08:38 +0100)]
net: phy: mdio-gpio: Fix working over slow can_sleep GPIOs
Up until commit
7e5fbd1e0700 ("net: mdio-gpio: Convert to use gpiod
functions where possible"), the _cansleep variants of the gpio_ API was
used. After that commit and the change to gpiod_ API, the _cansleep()
was dropped. This then results in WARN_ON() when used with GPIO
devices which do sleep. Add back the _cansleep() to avoid this.
Fixes: 7e5fbd1e0700 ("net: mdio-gpio: Convert to use gpiod functions where possible")
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 17 Nov 2018 07:04:37 +0000 (23:04 -0800)]
Revert "net: phy: mdio-gpio: Fix working over slow can_sleep GPIOs"
This reverts commit
dfa0d55ff6be64e7b6881212a291cb95f8da3b08.
Discussion still ongoing, I shouldn't have applied this.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 17 Nov 2018 04:26:30 +0000 (20:26 -0800)]
Merge tag 'batadv-net-for-davem-
20181114' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
Here are two batman-adv bugfixes:
- Explicitly pad short ELP packets with zeros, by Sven Eckelmann
- Fix packet size calculation when merging fragments,
by Sven Eckelmann
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Martin Schiller [Wed, 14 Nov 2018 11:54:49 +0000 (12:54 +0100)]
net: phy: mdio-gpio: Fix working over slow can_sleep GPIOs
This commit re-enables support for slow GPIO pins. It was initially
introduced by commit
2d6c9091ab76 ("net: mdio-gpio: support access that
may sleep") and got lost by commit
7e5fbd1e0700 ("net: mdio-gpio:
Convert to use gpiod functions where possible").
Also add a warning about slow GPIO pins like it is done in i2c-gpio.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Davide Caratti [Wed, 14 Nov 2018 11:17:25 +0000 (12:17 +0100)]
net/sched: act_pedit: fix memory leak when IDR allocation fails
tcf_idr_check_alloc() can return a negative value, on allocation failures
(-ENOMEM) or IDR exhaustion (-ENOSPC): don't leak keys_ex in these cases.
Fixes: 0190c1d452a9 ("net: sched: atomically check-allocate action")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christophe JAILLET [Tue, 13 Nov 2018 17:42:24 +0000 (18:42 +0100)]
net: lantiq: Fix returned value in case of error in 'xrx200_probe()'
Return 'err' in the error handling path instead of 0.
Return explicitly 0 in the normal path, instead of 'err', which is known
to be 0 at this point.
Fixes: fe1a56420cf2 ("net: lantiq: Add Lantiq / Intel VRX200 Ethernet driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Tue, 13 Nov 2018 16:48:28 +0000 (00:48 +0800)]
ipv6: fix a dst leak when removing its exception
These is no need to hold dst before calling rt6_remove_exception_rt().
The call to dst_hold_safe() in ip6_link_failure() was for ip6_del_rt(),
which has been removed in Commit
93531c674315 ("net/ipv6: separate
handling of FIB entries from dst based routes"). Otherwise, it will
cause a dst leak.
This patch is to simply remove the dst_hold_safe() call before calling
rt6_remove_exception_rt() and also do the same in ip6_del_cached_rt().
It's safe, because the removal of the exception that holds its dst's
refcnt is protected by rt6_exception_lock.
Fixes: 93531c674315 ("net/ipv6: separate handling of FIB entries from dst based routes")
Fixes: 23fb93a4d3f1 ("net/ipv6: Cleanup exception and cache route handling")
Reported-by: Li Shuang <shuali@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Maxime Chevallier [Fri, 9 Nov 2018 08:17:33 +0000 (09:17 +0100)]
net: mvneta: Don't advertise 2.5G modes
Using 2.5G speed relies on the SerDes lanes being configured
accordingly. The lanes have to be reconfigured to switch between
1G and 2.5G, and for now only the bootloader does this configuration.
In the case we add a Comphy driver to handle switching the lanes
dynamically, it's better for now to stick with supporting only 1G and
add advertisement for 2.5G once we really are capable of handling both
speeds without problem.
Since the interface mode is initialy taken from the DT, we want to make
sure that adding comphy support won't break boards that don't update
their dtb.
Fixes: da58a931f248 ("net: mvneta: Add support for 2500Mbps SGMII")
Reported-by: Andrew Lunn <andrew@lunn.ch>
Reported-by: Russell King <linux@armlinux.org.uk>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 16 Nov 2018 19:18:36 +0000 (13:18 -0600)]
Merge tag 'fsnotify_for_v4.20-rc3' of git://git./linux/kernel/git/jack/linux-fs
Pull fsnotify fix from Jan Kara:
"One small fsnotify fix for duplicate events"
* tag 'fsnotify_for_v4.20-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
fanotify: fix handling of events on child sub-directory
Linus Torvalds [Fri, 16 Nov 2018 17:38:14 +0000 (11:38 -0600)]
Merge tag 'gfs2-4.20.fixes3' of git://git./linux/kernel/git/gfs2/linux-gfs2
Pull bfs2 fixes from Andreas Gruenbacher:
"Fix two bugs leading to leaked buffer head references:
- gfs2: Put bitmap buffers in put_super
- gfs2: Fix iomap buffer head reference counting bug
And one bug leading to significant slow-downs when deleting large
files:
- gfs2: Fix metadata read-ahead during truncate (2)"
* tag 'gfs2-4.20.fixes3' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2:
gfs2: Fix iomap buffer head reference counting bug
gfs2: Fix metadata read-ahead during truncate (2)
gfs2: Put bitmap buffers in put_super
Andreas Gruenbacher [Sun, 11 Nov 2018 11:15:21 +0000 (11:15 +0000)]
gfs2: Fix iomap buffer head reference counting bug
GFS2 passes the inode buffer head (dibh) from gfs2_iomap_begin to
gfs2_iomap_end in iomap->private. It sets that private pointer in
gfs2_iomap_get. Users of gfs2_iomap_get other than gfs2_iomap_begin
would have to release iomap->private, but this isn't done correctly,
leading to a leak of buffer head references.
To fix this, move the code for setting iomap->private from
gfs2_iomap_get to gfs2_iomap_begin.
Fixes: 64bc06bb32 ("gfs2: iomap buffered write support")
Cc: stable@vger.kernel.org # v4.19+
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 16 Nov 2018 16:37:27 +0000 (10:37 -0600)]
Merge branch 'linus' of git://git./linux/kernel/git/herbert/crypto-2.6
Pull crypto fixes from Herbert Xu:
"This fixes the following issues:
- Potential memory overwrite in simd
- Kernel info leaks in crypto_user
- NULL dereference and use-after-free in hisilicon"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: user - Zeroize whole structure given to user space
crypto: user - fix leaking uninitialized memory to userspace
crypto: simd - correctly take reqsize of wrapped skcipher into account
crypto: hisilicon - Fix reference after free of memories on error path
crypto: hisilicon - Fix NULL dereference for same dst and src
Linus Torvalds [Fri, 16 Nov 2018 16:17:29 +0000 (10:17 -0600)]
Merge tag 'drm-fixes-2018-11-16' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Live from Vancouver, SoC maintainer talk, this weeks drm fixes pull
for rc3:
omapdrm:
- regression fixes for the reordering bridge stuff that went into rc1
i915:
- incorrect EU count fix
- HPD storm fix
- MST fix
- relocation fix for gen4/5
amdgpu:
- huge page handling fix
- IH ring setup
- XGMI aperture setup
- watermark setup fix
misc:
- docs and MST fix"
* tag 'drm-fixes-2018-11-16' of git://anongit.freedesktop.org/drm/drm: (23 commits)
drm/i915: Account for scale factor when calculating initial phase
drm/i915: Clean up skl_program_scaler()
drm/i915: Move programming plane scaler to its own function.
drm/i915/icl: Drop spurious register read from icl_dbuf_slices_update
drm/i915: fix broadwell EU computation
drm/amdgpu: fix huge page handling on Vega10
drm/amd/pp: Fix truncated clock value when set watermark
drm/amdgpu: fix bug with IH ring setup
drm/meson: venc: dmt mode must use encp
drm/amdgpu: set system aperture to cover whole FB region
drm/i915: Fix hpd handling for pins with two encoders
drm/i915/execlists: Force write serialisation into context image vs execution
drm/i915/icl: Fix power well 2 wrt. DC-off toggling order
drm/i915: Fix NULL deref when re-enabling HPD IRQs on systems with MST
drm/i915: Fix possible race in intel_dp_add_mst_connector()
drm/i915/ringbuffer: Delay after EMIT_INVALIDATE for gen4/gen5
drm/omap: dsi: Fix missing of_platform_depopulate()
drm/omap: Move DISPC runtime PM handling to omapdrm
drm/omap: dsi: Ensure the device is active during probe
drm/omap: hdmi4: Ensure the device is active during bind
...
Linus Torvalds [Fri, 16 Nov 2018 16:14:54 +0000 (10:14 -0600)]
Merge tag 'powerpc-4.20-3' of git://git./linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Two weeks worth of fixes since rc1.
- I broke 16-byte alignment of the stack when we moved PPR into
pt_regs. Despite being required by the ABI this broke almost
nothing, we eventually hit it in code where GCC does arithmetic on
the stack pointer assuming the bottom 4 bits are clear. Fix it by
padding the in-kernel pt_regs by 8 bytes.
- A couple of commits fixing minor bugs in the recent SLB rewrite.
- A build fix related to tracepoints in KVM in some configurations.
- Our old "IO workarounds" code written for Cell couldn't coexist in
a kernel that runs on Power9 with the Radix MMU, fix that.
- Remove the NPU DMA ops, these just printed a warning and should
never have been called.
- Suppress an overly chatty message triggered by CPU hotplug in some
configs.
- Two small selftest fixes.
Thanks to: Alistair Popple, Gustavo Romero, Nicholas Piggin, Satheesh
Rajendran, Scott Wood"
* tag 'powerpc-4.20-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
selftests/powerpc: Adjust wild_bctr to build with old binutils
powerpc/64: Fix kernel stack 16-byte alignment
powerpc/numa: Suppress "VPHN is not supported" messages
selftests/powerpc: Fix wild_bctr test to work on ppc64
powerpc/io: Fix the IO workarounds code to work with Radix
powerpc/mm/64s: Fix preempt warning in slb_allocate_kernel()
KVM: PPC: Move and undef TRACE_INCLUDE_PATH/FILE
powerpc/mm/64s: Only use slbfee on CPUs that support it
powerpc/mm/64s: Use PPC_SLBFEE macro
powerpc/mm/64s: Consolidate SLB assertions
powerpc/powernv/npu: Remove NPU DMA ops
Linus Torvalds [Fri, 16 Nov 2018 16:10:27 +0000 (10:10 -0600)]
Merge tag 'xtensa-
20181115' of git://github.com/jcmvbkbc/linux-xtensa
Pull Xtensa fixes from Max Filippov:
- fix stack alignment for bFLT binaries.
- fix physical-to-virtual address translation for boot parameters in
MMUv3 256+256 and 512+512 virtual memory layouts.
* tag 'xtensa-
20181115' of git://github.com/jcmvbkbc/linux-xtensa:
xtensa: fix boot parameters address translation
xtensa: make sure bFLT stack is 16 byte aligned
Linus Torvalds [Fri, 16 Nov 2018 15:31:59 +0000 (09:31 -0600)]
Merge tag 'for-linus-
20181115' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
- Discard loop fix, caused by integer overflow (Dave)
- Blacklist of Samsung drive that hangs with power management (Diego)
- Copy bio priority when cloning it (Hannes)
- Fix race condition exposed in floppy (me)
- Fix SCSI queue cleanup regression. While elusive, it caused oopses in
queue running (Ming)
- Fix bad string copy in kyber tracing (Omar)
* tag 'for-linus-
20181115' of git://git.kernel.dk/linux-block:
SCSI: fix queue cleanup race before queue initialization is done
block: fix 32 bit overflow in __blkdev_issue_discard()
libata: blacklist SAMSUNG MZ7TD256HAFV-000L9 SSD
block: copy ioprio in __bio_clone_fast() and bounce
kyber: fix wrong strlcpy() size in trace_kyber_latency()
floppy: fix race condition in __floppy_read_block_0()
Linus Torvalds [Fri, 16 Nov 2018 15:30:13 +0000 (09:30 -0600)]
Merge tag 'fuse-fixes-4.20-rc3' of git://git./linux/kernel/git/mszeredi/fuse
Pull fuse fixes from Miklos Szeredi:
"A couple of fixes, all bound for -stable (i.e. not regressions in this
cycle)"
* tag 'fuse-fixes-4.20-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: fix use-after-free in fuse_direct_IO()
fuse: fix possibly missed wake-up after abort
fuse: fix leaked notify reply
Andrew Morton [Fri, 16 Nov 2018 00:15:20 +0000 (16:15 -0800)]
drivers/net/ethernet/qlogic/qed/qed_rdma.h: fix typo
Add missing semicolon.
Fixes: 291d57f67d244973 ("qed: Fix rdma_info structure allocation")
Cc: Michal Kalderon <michal.kalderon@cavium.com>
Cc: Denis Bolotin <denis.bolotin@cavium.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 16 Nov 2018 00:09:31 +0000 (16:09 -0800)]
Merge branch 'mlx4-fixes'
Tariq Toukan says:
====================
mlx4 fixes for 4.20-rc
This patchset includes small fixes for mlx4_core driver.
First patch by Jack zeros a field in a FW communication
command, to match the FW spec.
Please queue it to -stable >= v3.17.
In the second patch I zero-initialize a variable to silence
a compliation warning.
Please queue it to -stable >= v3.19.
Third patch by Aya replaces int fields with unsigned int,
to fix a UBSAN warning.
Please queue it to -stable >= v3.13.
Series generated against net commit:
db8ddde766ad Merge branch 'qed-Miscellaneous-bug-fixes'
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Aya Levin [Thu, 15 Nov 2018 16:05:15 +0000 (18:05 +0200)]
net/mlx4: Fix UBSAN warning of signed integer overflow
UBSAN: Undefined behavior in
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c:626:29
signed integer overflow:
1802201963 +
1802201963 cannot be represented
in type 'int'
The union of res_reserved and res_port_rsvd[MLX4_MAX_PORTS] monitors
granting of reserved resources. The grant operation is calculated and
protected, thus both members of the union cannot be negative. Changed
type of res_reserved and of res_port_rsvd[MLX4_MAX_PORTS] from signed
int to unsigned int, allowing large value.
Fixes: 5a0d0a6161ae ("mlx4: Structures and init/teardown for VF resource quotas")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tariq Toukan [Thu, 15 Nov 2018 16:05:14 +0000 (18:05 +0200)]
net/mlx4_core: Fix uninitialized variable compilation warning
Initialize the uid variable to zero to avoid the compilation warning.
Fixes: 7a89399ffad7 ("net/mlx4: Add mlx4_bitmap zone allocator")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jack Morgenstein [Thu, 15 Nov 2018 16:05:13 +0000 (18:05 +0200)]
net/mlx4_core: Zero out lkey field in SW2HW_MPT fw command
When re-registering a user mr, the mpt information for the
existing mr when running SRIOV is obtained via the QUERY_MPT
fw command. The returned information includes the mpt's lkey.
This retrieved mpt information is used to move the mpt back
to hardware ownership in the rereg flow (via the SW2HW_MPT
fw command when running SRIOV).
The fw API spec states that for SW2HW_MPT, the lkey field
must be zero. Any ConnectX-3 PF driver which checks for strict spec
adherence will return failure for SW2HW_MPT if the lkey field is not
zero (although the fw in practice ignores this field for SW2HW_MPT).
Thus, in order to conform to the fw API spec, set the lkey field to zero
before invoking SW2HW_MPT when running SRIOV.
Fixes: e630664c8383 ("mlx4_core: Add helper functions to support MR re-registration")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Burton [Mon, 12 Nov 2018 22:18:01 +0000 (22:18 +0000)]
MIPS: Loongson3,SGI-IP27: Simplify max_low_pfn calculation
Both the Loongson3 & SGI-IP27 platforms set max_low_pfn to the last
available PFN describing memory. They both do it in paging_init() which
is later than ideal since max_low_pfn is used before that function is
called. Simplify both platforms to trivially initialize max_low_pfn
using the end address of DRAM, and do it earlier in prom_meminit().
Signed-off-by: Paul Burton <paul.burton@mips.com>
Suggested-by: Mike Rapoport <rppt@linux.ibm.com>
Tested-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Patchwork: https://patchwork.linux-mips.org/patch/21104/
References: https://patchwork.linux-mips.org/patch/21031/
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Mike Rapoport <rppt@linux.ibm.com>
Cc: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Cc: linux-mips@linux-mips.org
Dave Airlie [Thu, 15 Nov 2018 22:52:14 +0000 (08:52 +1000)]
Merge tag 'drm-intel-fixes-2018-11-15' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
- Fix Bugzilla #108712: Fix incorrect EU count report from kernel
- Fix to account for scale factor when calculating initial phase on scaled output
- Avoid too trigger-happy HPD storm detection and fix a race and an OOPS for MST systems.
- Relocation race fix for Gen4/5
- A couple ICL fixes and dependencies for above Fixes:.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181115164709.GA13430@jlahtine-desk.ger.corp.intel.com
Eric Dumazet [Tue, 13 Nov 2018 00:17:16 +0000 (16:17 -0800)]
net_sched: sch_fq: ensure maxrate fq parameter applies to EDT flows
When EDT conversion happened, fq lost the ability to enfore a maxrate
for all flows. It kept it for non EDT flows.
This commit restores the functionality.
Tested:
tc qd replace dev eth0 root fq maxrate 500Mbit
netperf -P0 -H host -- -O THROUGHPUT
489.75
Fixes: ab408b6dc744 ("tcp: switch tcp and sch_fq to new earliest departure time model")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Howells [Mon, 12 Nov 2018 22:33:22 +0000 (22:33 +0000)]
rxrpc: Fix life check
The life-checking function, which is used by kAFS to make sure that a call
is still live in the event of a pending signal, only samples the received
packet serial number counter; it doesn't actually provoke a change in the
counter, rather relying on the server to happen to give us a packet in the
time window.
Fix this by adding a function to force a ping to be transmitted.
kAFS then keeps track of whether there's been a stall, and if so, uses the
new function to ping the server, resetting the timeout to allow the reply
to come back.
If there's a stall, a ping and the call is *still* stalled in the same
place after another period, then the call will be aborted.
Fixes: bc5e3a546d55 ("rxrpc: Use MSG_WAITALL to tell sendmsg() to temporarily ignore signals")
Fixes: f4d15fb6f99a ("rxrpc: Provide functions for allowing cleaner handling of signals")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ganesh Goudar [Thu, 15 Nov 2018 10:06:21 +0000 (15:36 +0530)]
cxgb4: fix thermal zone build error
with CONFIG_THERMAL=m and cxgb4 as built-in build fails, and
'commit
e70a57fa59bb ("cxgb4: fix thermal configuration dependencies")'
tries to fix it but when cxgb4i is made built-in build fails again,
use IS_REACHABLE instead of IS_ENABLED to fix the issue.
Fixes: e70a57fa59bb (cxgb4: fix thermal configuration dependencies)
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thor Thayer [Mon, 12 Nov 2018 17:50:56 +0000 (11:50 -0600)]
MAINTAINERS: Replace Vince Bridgers as Altera TSE maintainer
Vince has moved to a different role. Replace him as Altera
TSE maintainer.
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Acked-by: Vince Bridgers <vince.bridgers@intel.com>
Acked-by: Alan Tull <atull@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 15 Nov 2018 17:37:16 +0000 (09:37 -0800)]
Merge branch 'bnxt_en-Bug-fixes'
Michael Chan says:
====================
bnxt_en: Bug fixes.
Most of the bug fixes are related to the new 57500 chips, including some
initialization and counter fixes, disabling RDMA support, and a
workaround for occasional missing interrupts. The last patch from
Vasundhara fixes the year/month parameters for firmware coredump.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Vasundhara Volam [Thu, 15 Nov 2018 08:25:42 +0000 (03:25 -0500)]
bnxt_en: Fix filling time in bnxt_fill_coredump_record()
Fix the year and month offset while storing it in
bnxt_fill_coredump_record().
Fixes: 6c5657d085ae ("bnxt_en: Add support for ethtool get dump.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Thu, 15 Nov 2018 08:25:41 +0000 (03:25 -0500)]
bnxt_en: Add software "missed_irqs" counter.
To keep track of the number of times the workaround code for 57500 A0
has been triggered. This is a per NQ counter.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Thu, 15 Nov 2018 08:25:40 +0000 (03:25 -0500)]
bnxt_en: Workaround occasional TX timeout on 57500 A0.
Hardware can sometimes not generate NQ MSIX with a single pending
CP ring entry. This seems to always happen at the last entry of
the CP ring before it wraps. Add logic to check all the CP rings for
pending entries without the CP ring consumer index advancing. Calling
HWRM_DBG_RING_INFO_GET to read the context of the CP ring will flush
out the NQ entry and MSIX.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Thu, 15 Nov 2018 08:25:39 +0000 (03:25 -0500)]
bnxt_en: Disable RDMA support on the 57500 chips.
There is no RDMA support on 57500 chips yet, so prevent bnxt_re from
registering on these chips. There is intermittent failure if bnxt_re
is allowed to register and proceed with RDMA operations.
Fixes: 1ab968d2f1d6 ("bnxt_en: Add PCI ID for BCM57508 device.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Thu, 15 Nov 2018 08:25:38 +0000 (03:25 -0500)]
bnxt_en: Fix rx_l4_csum_errors counter on 57500 devices.
The software counter structure is defined in both the CP ring's structure
and the NQ ring's structure on the new devices. The legacy code adds the
counter to the CP ring's structure and the counter won't get displayed
since the ethtool code is looking at the NQ ring's structure.
Since all other counters are contained in the NQ ring's structure, it
makes more sense to count rx_l4_csum_errors in the NQ.
Fixes: 50e3ab7836b5 ("bnxt_en: Allocate completion ring structures for 57500 series chips.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Thu, 15 Nov 2018 08:25:37 +0000 (03:25 -0500)]
bnxt_en: Fix RSS context allocation.
Recent commit has added the reservation of RSS context. This requires
bnxt_hwrm_vnic_qcaps() to be called before allocating any RSS contexts.
The bnxt_hwrm_vnic_qcaps() call sets up proper flags that will
determine how many RSS contexts to allocate to support NTUPLE.
This causes a regression that too many RSS contexts are being reserved
and causing resource shortage when enabling many VFs. Fix it by calling
bnxt_hwrm_vnic_qcaps() earlier.
Fixes: 41e8d7983752 ("bnxt_en: Modify the ring reservation functions for 57500 series chips.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 15 Nov 2018 17:26:09 +0000 (11:26 -0600)]
Merge tag 'selinux-pr-
20181115' of git://git./linux/kernel/git/pcmoore/selinux
Pull SELinux fixes from Paul Moore:
"Two small SELinux fixes for v4.20.
Ondrej's patch adds a check on user input, and my patch ensures we
don't look past the end of a buffer.
Both patches are quite small and pass the selinux-testsuite"
* tag 'selinux-pr-
20181115' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux:
selinux: fix non-MLS handling in mls_context_to_sid()
selinux: check length properly in SCTP bind hook
Linus Torvalds [Thu, 15 Nov 2018 17:20:06 +0000 (11:20 -0600)]
Merge tag 'pinctrl-v4.20-2' of git://git./linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
- A bunch of fixes for the Allwinner meson platform
- Establish a git repo for Intel pin control in MAINTAINERS
* tag 'pinctrl-v4.20-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
MAINTAINERS: Add tree link for Intel pin control driver
pinctrl: meson: fix meson8b ao pull register bits
pinctrl: meson: fix meson8 ao pull register bits
pinctrl: meson: fix gxl ao pull register bits
pinctrl: meson: fix gxbb ao pull register bits
pinctrl: meson: fix pinconf bias disable
Linus Torvalds [Thu, 15 Nov 2018 16:59:37 +0000 (10:59 -0600)]
Merge tag 'nfs-for-4.20-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
"Highlights include:
Stable fixes:
- Don't exit the NFSv4 state manager without clearing
NFS4CLNT_MANAGER_RUNNING
Bugfixes:
- Fix an Oops when destroying the RPCSEC_GSS credential cache
- Fix an Oops during delegation callbacks
- Ensure that the NFSv4 state manager exits the loop on SIGKILL
- Fix a bogus get/put in generic_key_to_expire()"
* tag 'nfs-for-4.20-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFSv4: Fix an Oops during delegation callbacks
SUNRPC: Fix a bogus get/put in generic_key_to_expire()
SUNRPC: Fix a Oops when destroying the RPCSEC_GSS credential cache
NFSv4: Ensure that the state manager exits the loop on SIGKILL
NFSv4: Don't exit the state manager without clearing NFS4CLNT_MANAGER_RUNNING
Dave Airlie [Thu, 15 Nov 2018 16:14:42 +0000 (02:14 +1000)]
Merge branch 'drm-fixes-4.20' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
Fixes for 4.20:
- Fix for huge page handling that caused a GPUVM fault in some cases
- Fix IH ring setup
- Fix for xgmi aperture setup
- Fix for watermark setup for SMU
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181114171853.2866-1-alexander.deucher@amd.com
Dave Airlie [Thu, 15 Nov 2018 16:12:27 +0000 (02:12 +1000)]
Merge tag 'drm-misc-fixes-2018-11-14' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
Cross-subsystem:
- omap: Instantiate dss children in omapdss instead of mach (Laurent)
Other:
- htmldocs build warning (Sean)
- MST NULL deref fix (Stanislav)
- omap: Various runtime ref gets on probe/bind (Laurent)
- omap: Fix to the above dss children patch (Tony)
Cc: Sean Paul <sean@poorly.run>
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20181114204542.GA52569@art_vandelay
Gustavo Romero [Thu, 15 Nov 2018 02:33:30 +0000 (21:33 -0500)]
selftests/powerpc: Adjust wild_bctr to build with old binutils
Currently the selftest wild_bctr can fail to build when an old gcc is
used, notably on gcc using a binutils version <= 2.27, because the
assembler does not support the integer suffix UL.
This patch adjusts the wild_bctr test so the REG_POISON value is still
treated as an unsigned long for the shifts on compilation but the UL
suffix is absent on the stringification, so the inline asm code
generated has no UL suffixes.
Signed-off-by: Gustavo Romero <gromero@linux.vnet.ibm.com>
[mpe: Wrap long line]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Ville Syrjälä [Wed, 14 Nov 2018 13:32:55 +0000 (15:32 +0200)]
drm/i915: Account for scale factor when calculating initial phase
To get the initial phase correct we need to account for the scale
factor as well. I forgot this initially and was mostly looking at
heavily upscaled content where the minor difference between -0.5
and the proper initial phase was not readily apparent.
And let's toss in a comment that tries to explain the formula
a little bit.
v2: The initial phase upper limit is 1.5, not 24.0!
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Fixes: 0a59952b24e2 ("drm/i915: Configure SKL+ scaler initial phase correctly")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181029181820.21956-1-ville.syrjala@linux.intel.com
Tested-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Tested-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> #irc
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> #irc
(cherry picked from commit
e7a278a329dd8aa2c70c564849f164cb5673689c)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Ville Syrjälä [Wed, 14 Nov 2018 11:49:24 +0000 (13:49 +0200)]
drm/i915: Clean up skl_program_scaler()
Remove the "sizes are 0 based" stuff that is not even true for the
scaler.
v2: Rebase
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181101151736.20522-1-ville.syrjala@linux.intel.com
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
(cherry picked from commit
d0105af939769393d6447a04cee2d1ae12e3f09a)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Maarten Lankhorst [Wed, 14 Nov 2018 11:49:23 +0000 (13:49 +0200)]
drm/i915: Move programming plane scaler to its own function.
This cleans the code up slightly, and will make other changes easier.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180920102711.4184-8-maarten.lankhorst@linux.intel.com
(cherry picked from commit
ab5c60bf76755d24ae8de5c1c6ac594934656ace)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Ard Biesheuvel [Wed, 14 Nov 2018 17:55:44 +0000 (09:55 -0800)]
efi: Permit calling efi_mem_reserve_persistent() from atomic context
Currently, efi_mem_reserve_persistent() may not be called from atomic
context, since both the kmalloc() call and the memremap() call may
sleep.
The kmalloc() call is easy enough to fix, but the memremap() call
needs to be moved into an init hook since we cannot control the
memory allocation behavior of memremap() at the call site.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/20181114175544.12860-6-ard.biesheuvel@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Ard Biesheuvel [Wed, 14 Nov 2018 17:55:43 +0000 (09:55 -0800)]
efi/arm: Defer persistent reservations until after paging_init()
The new memory EFI reservation feature we introduced to allow memory
reservations to persist across kexec may trigger an unbounded number
of calls to memblock_reserve(). The memblock subsystem can deal with
this fine, but not before memblock resizing is enabled, which we can
only do after paging_init(), when the memory we reallocate the array
into is actually mapped.
So break out the memreserve table processing into a separate routine
and call it after paging_init() on arm64. On ARM, because of limited
reviewing bandwidth of the maintainer, we cannot currently fix this,
so instead, disable the EFI persistent memreserve entirely on ARM so
we can fix it later.
Tested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/20181114175544.12860-5-ard.biesheuvel@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Ard Biesheuvel [Wed, 14 Nov 2018 17:55:42 +0000 (09:55 -0800)]
efi/arm/libstub: Pack FDT after populating it
Commit:
24d7c494ce46 ("efi/arm-stub: Round up FDT allocation to mapping size")
increased the allocation size for the FDT image created by the stub to a
fixed value of 2 MB, to simplify the former code that made several
attempts with increasing values for the size. This is reasonable
given that the allocation is of type EFI_LOADER_DATA, which is released
to the kernel unless it is explicitly memblock_reserve()d by the early
boot code.
However, this allocation size leaked into the 'size' field of the FDT
header metadata, and so the entire allocation remains occupied by the
device tree binary, even if most of it is not used to store device tree
information.
So call fdt_pack() to shrink the FDT data structure to its minimum size
after populating all the fields, so that the remaining memory is no
longer wasted.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: <stable@vger.kernel.org> # v4.12+
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Fixes: 24d7c494ce46 ("efi/arm-stub: Round up FDT allocation to mapping size")
Link: http://lkml.kernel.org/r/20181114175544.12860-4-ard.biesheuvel@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Ard Biesheuvel [Wed, 14 Nov 2018 17:55:41 +0000 (09:55 -0800)]
efi/arm: Revert deferred unmap of early memmap mapping
Commit:
3ea86495aef2 ("efi/arm: preserve early mapping of UEFI memory map longer for BGRT")
deferred the unmap of the early mapping of the UEFI memory map to
accommodate the ACPI BGRT code, which looks up the memory type that
backs the BGRT table to validate it against the requirements of the UEFI spec.
Unfortunately, this causes problems on ARM, which does not permit
early mappings to persist after paging_init() is called, resulting
in a WARN() splat. Since we don't support the BGRT table on ARM anway,
let's revert ARM to the old behaviour, which is to take down the
early mapping at the end of efi_init().
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Fixes: 3ea86495aef2 ("efi/arm: preserve early mapping of UEFI memory ...")
Link: http://lkml.kernel.org/r/20181114175544.12860-3-ard.biesheuvel@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Waiman Long [Wed, 14 Nov 2018 17:55:40 +0000 (09:55 -0800)]
efi: Fix debugobjects warning on 'efi_rts_work'
The following commit:
9dbbedaa6171 ("efi: Make efi_rts_work accessible to efi page fault handler")
converted 'efi_rts_work' from an auto variable to a global variable.
However, when submitting the work, INIT_WORK_ONSTACK() was still used,
causing the following complaint from debugobjects:
ODEBUG: object
00000000ed27b500 is NOT on stack
00000000c7d38760, but annotated.
Change the macro to just INIT_WORK() to eliminate the warning.
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Sai Praneeth Prakhya <sai.praneeth.prakhya@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Fixes: 9dbbedaa6171 ("efi: Make efi_rts_work accessible to efi page fault handler")
Link: http://lkml.kernel.org/r/20181114175544.12860-2-ard.biesheuvel@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Xin Long [Mon, 12 Nov 2018 17:08:25 +0000 (01:08 +0800)]
l2tp: fix a sock refcnt leak in l2tp_tunnel_register
This issue happens when trying to add an existent tunnel. It
doesn't call sock_put() before returning -EEXIST to release
the sock refcnt that was held by calling sock_hold() before
the existence check.
This patch is to fix it by holding the sock after doing the
existence check.
Fixes: f6cd651b056f ("l2tp: fix race in duplicate tunnel detection")
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nicholas Piggin [Thu, 15 Nov 2018 02:34:27 +0000 (12:34 +1000)]
powerpc/64: Fix kernel stack 16-byte alignment
Commit
4c2de74cc869 ("powerpc/64: Interrupts save PPR on stack rather
than thread_struct") changed sizeof(struct pt_regs) % 16 from 0 to 8,
which causes the interrupt frame allocation on kernel entry to put the
kernel stack out of alignment.
Quadword (16-byte) alignment for the stack is required by both the
64-bit v1 ABI (v1.9 § 3.2.2) and the 64-bit v2 ABI (v1.1 § 2.2.2.1).
Add a pad field to fix alignment, and add a BUILD_BUG_ON to catch this
in future.
Fixes: 4c2de74cc869 ("powerpc/64: Interrupts save PPR on stack rather than thread_struct")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Linus Torvalds [Wed, 14 Nov 2018 23:14:40 +0000 (17:14 -0600)]
Merge tag 'riscv-for-linus-4.20-rc2' of git://git./linux/kernel/git/palmer/riscv-linux
Pull RISC-V fixes from Palmer Dabbelt:
"This contains a few patches that fix various issues in the RISC-V
port:
- enable printk timestamps in the RISC-V defconfig.
- a whitespace fix to "struct pt_regs".
- add a "vdso_install" target for RISC-V.
- a pair of build fixes: one to fix a typo in our makefile, and one
to clean up some warnings.
There will probably be more patches from us for 4.20, but I don't have
anything that's ready to go right now so I'm going to hold off a bit.
Right now the only concrete thing I know I want to make sure gets
sorted out is our 32-bit stat interface, which I don't want sitting in
limbo for another cycle as we have to get RV32I glibc sone"
* tag 'riscv-for-linus-4.20-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux:
RISC-V: Silence some module warnings on 32-bit
RISC-V: lib: Fix build error for 64-bit
riscv: add missing vdso_install target
riscv: fix spacing in struct pt_regs
RISC-V: defconfig: Enable printk timestamps
Linus Torvalds [Wed, 14 Nov 2018 23:07:01 +0000 (17:07 -0600)]
Merge tag 'kgdb-fixes-4.20-rc3' of https://git.linaro.org/people/daniel.thompson/linux
Pull kgdb fixes from Daniel Thompson:
"The most important changes here are two fixes for kdb regressions
causes by the hashing of %p pointers together with a fix for a
potential overflow in kdb tab completion handling (and warning fix).
Also included are a set of changes in preparation to (eventually)
enable -Wimplicit-fallthrough"
* tag 'kgdb-fixes-4.20-rc3' of https://git.linaro.org/people/daniel.thompson/linux:
kdb: kdb_support: mark expected switch fall-throughs
kdb: kdb_keyboard: mark expected switch fall-throughs
kdb: kdb_main: refactor code in kdb_md_line
kdb: Use strscpy with destination buffer size
kdb: print real address of pointers instead of hashed addresses
kdb: use correct pointer when 'btc' calls 'btt'
Linus Torvalds [Wed, 14 Nov 2018 23:03:24 +0000 (17:03 -0600)]
Merge branch 'fixes-v4.20-rc3' of git://git./linux/kernel/git/jmorris/linux-security
Pull integrity fix from James Morris:
"Fix a bug introduced with in this merge window in
82f94f24475c ("KEYS:
Provide software public key query function [ver #2]")"
* 'fixes-v4.20-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
integrity: support new struct public_key_signature encoding field
Ursula Braun [Mon, 12 Nov 2018 16:06:12 +0000 (17:06 +0100)]
s390/ism: clear dmbe_mask bit before SMC IRQ handling
SMC-D stress workload showed connection stalls. Since the firmware
decides to skip raising an interrupt if the SBA DMBE mask bit is
still set, this SBA DMBE mask bit should be cleared before the
IRQ handling in the SMC code runs. Otherwise there are small windows
possible with missing interrupts for incoming data.
SMC-D currently does not care about the old value of the SBA DMBE
mask.
Acked-by: Sebastian Ott <sebott@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 14 Nov 2018 21:36:45 +0000 (15:36 -0600)]
Merge tag 'acpi-4.20-rc3' of git://git./linux/kernel/git/rafael/linux-pm
Pull ACPI fix from Rafael Wysocki:
"Fix a recently introduced build issue in the xpower PMIC driver (Arnd
Bergmann)"
* tag 'acpi-4.20-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / PMIC: xpower: fix IOSF_MBI dependency
Linus Torvalds [Wed, 14 Nov 2018 21:33:45 +0000 (15:33 -0600)]
Merge tag 'pm-4.20-rc3' of git://git./linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These remove a stale DT entry left behind after recent removal of a
cpufreq driver without users, fix up error handling in the imx6q
cpufreq driver, fix two issues in the cpufreq documentation, and
update the ARM cpufreq driver.
Specifics:
- Drop stale DT binding for the arm_big_little_dt driver removed
recently (Sudeep Holla).
- Fix up error handling in the imx6q cpufreq driver to make it report
voltage scaling failures (Anson Huang).
- Fix two issues in the cpufreq documentation (Viresh Kumar, Zhao Wei
Liew).
- Fix ARM cpuidle driver initialization regression from the 4.19 time
frame and rework the driver registration part of it to simplify
code (Ulf Hansson)"
* tag 'pm-4.20-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ARM: cpuidle: Convert to use cpuidle_register|unregister()
ARM: cpuidle: Don't register the driver when back-end init returns -ENXIO
dt-bindings: cpufreq: remove stale arm_big_little_dt entry
Documentation: cpufreq: Correct a typo
cpufreq: imx6q: add return value check for voltage scale
Documentation: cpu-freq: Frequencies aren't always sorted
Linus Torvalds [Wed, 14 Nov 2018 21:31:15 +0000 (15:31 -0600)]
Merge tag 'nfsd-4.20-1' of git://linux-nfs.org/~bfields/linux
Pull nfsd fixes from Bruce Fields:
"Three nfsd bugfixes.
None are new bugs, but they all take a little effort to hit, which
might explain why they weren't found sooner"
* tag 'nfsd-4.20-1' of git://linux-nfs.org/~bfields/linux:
SUNRPC: drop pointless static qualifier in xdr_get_next_encode_buffer()
nfsd: COPY and CLONE operations require the saved filehandle to be set
sunrpc: correct the computation for page_ptr when truncating
Linus Torvalds [Wed, 14 Nov 2018 19:51:47 +0000 (13:51 -0600)]
Merge tag 'pci-v4.20-fixes-1' of git://git./linux/kernel/git/helgaas/pci
Pull PCI fix from Bjorn Helgaas:
"Revert a _PXM change that causes silent early boot failure on some AMD
ThreadRipper systems"
* tag 'pci-v4.20-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
Revert "ACPI/PCI: Pay attention to device-specific _PXM node values"
Linus Torvalds [Wed, 14 Nov 2018 19:49:29 +0000 (13:49 -0600)]
Merge tag 'scsi-fixes' of git://git./linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is mostly a set of minor and obvious fixes (three in one of the
new drivers).
The only substantial change is to move the ufs to the blk-mq now that
the merge window fixed the suspend/resume issues with blk-mq"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: qla2xxx: Initialize port speed to avoid setting lower speed
Revert "scsi: ufs: Disable blk-mq for now"
scsi: NCR5380: Return false instead of NULL
scsi: qla2xxx: Fix a typo in MODULE_PARM_DESC
scsi: hisi_sas: Remove set but not used variable 'dq_list'
scsi: myrs: only build on little-endian platforms
scsi: myrs: avoid stack overflow warning
scsi: lpfc: fix remoteport access
scsi: myrb: fix sprintf buffer overflow warning
scsi: target/core: Avoid that a kernel oops is triggered when COMPARE AND WRITE fails
projects / openwrt / staging / blogic.git / log