drm/i915/icl: Add register defs for voltage swing sequences for MG PHY DDI

On Icelake platform, MG PHY is used when operating in DP alternate
mode or the legacy HDMI or DP modes. DDI Ports C, D, E, F are MG PHY
DDI ports on ICL.

This patch adds the necessary voltage swing programming related
register definitions and macros for MG PHY DDI ports.

v4 (from Paulo):
* Use _PORT instead of _PICK
* Change some mask names to our current coding standards
* Stay under 80 columns
v3:
* Rebase on new revision of patches
v2:
* Remove whitespaces in the #defines (Paulo)

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180323172419.24911-4-paulo.r.zanoni@intel.com

drm/i915/icl: Add Combo PHY DDI Buffer translation tables for Icelake.

These tables are used on voltage vswing sequence initialization on
Icelake.

The swing_sel on the spec's table is defined in a 4 bits binary like
1010.  However the register bits are split in upper 1 bit swing_sel
and lower 3 bits swing sel.

In this table here we store this value as a single value in hex like
it is mentioned in the Bspec and split it to the upper and lower bit
values only while programming the registers.

For instance: b1010 is written as 0xA and then while writing to the
register, the upper 1 bit is obtained by (0xA & 0x8) and shifting by
appropriate bits while lower 3 bits are obtained by (0xA & 0x7) and
shifting by appropriate bits.

Some of the columns need to be updated after the spec is updated.

v5 (from Paulo):
* Checkpatch fixes.
v4 (from Paulo):
* Fix minor typo
* Coding style conformance
v3:
* Get rid of HDMI/DVI tables, same as DP (Paulo)
* Use combo_phy in ddi buf trans table defs (Paulo)
v2:
* Added DW4_scaling_hex column to the translation tables (Rodrigo)

Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180323172419.24911-3-paulo.r.zanoni@intel.com

drm/i915/icl: Add register definitions for Combo PHY vswing sequences.

This patch defines register definitions required for ICL voltage
vswing programming for Combo PHY DDI Ports. It uses the same bit
definitions and macros as the CNL voltage swing sequences.

v8 (from Paulo):
* Rebase.
v7:
* Kill _MMIIO_PORT2_LN (Paulo)
v6:
* Replace some spaces with TAB (Paulo)
v5:
* Use _PORT instead of _PICK (Paulo)
* Remove DW7 defs for ICL, not used (Paulo)
v4:
* Rebase after _PICK was used instead of _PORT3
* Use _PICK for _MMIO_PORT2 since address of B is less
than address of A so cant use the math (Paulo)
v3:
* Make changes to the existing macro in a diff patch (Paulo)
v2:
* Add new defs fro ICL regs (Paulo)

Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180323172419.24911-2-paulo.r.zanoni@intel.com

drm/i915: Fix hibernation with ACPI S0 target state

After

commit dd9f31c7a3887950cbd0d49eb9d43f7a1518a356
Author: Imre Deak <imre.deak@intel.com>
Date:   Wed Aug 16 17:46:07 2017 +0300

    drm/i915/gen9+: Set same power state before hibernation image
    save/restore

during hibernation/suspend the power domain functionality got disabled,
after which resume could leave it incorrectly disabled if the ACPI
target state was S0 during suspend and i915 was not loaded by the loader
kernel.

This was caused by not considering if we resumed from hibernation as the
condition for power domains reiniting.

Fix this by simply tracking if we suspended power domains during system
suspend and reinit power domains accordingly during resume. This will
result in reiniting power domains always when resuming from hibernation,
regardless of the platform and whether or not i915 is loaded by the
loader kernel.

The reason we didn't catch this earlier is that the enabled/disabled
state of power domains during PMSG_FREEZE/PMSG_QUIESCE is platform
and kernel config dependent: on my SKL the target state is S4
during PMSG_FREEZE and (with the driver loaded in the loader kernel)
S0 during PMSG_QUIESCE. On the reporter's machine it's S0 during
PMSG_FREEZE but (contrary to this) power domains are not initialized
during PMSG_QUIESCE since i915 is not loaded in the loader kernel, or
it's loaded but without the DMC firmware being available.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105196
Reported-and-tested-by: amn-bas@hotmail.com
Fixes: dd9f31c7a388 ("drm/i915/gen9+: Set same power state before hibernation image save/restore")
Cc: amn-bas@hotmail.com
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180322143642.26883-1-imre.deak@intel.com

drm/i915: Actually flush interrupts on reset not just wedging

Commit 0f36a85c3bd5 ("drm/i915: Flush pending interrupt following a GPU
reset") got confused and only applied the flush to the set-wedge path
(which itself is proving troublesome), but we also need the
serialisation on the regular reset path. Oops.

Move the interrupt into reset_irq() and make it common to the reset and
final set-wedge.

v2: reset_irq() after port cancellation, as we assert that
execlists->active is sane for cancellation (and is being reset by
reset_irq).

References: 0f36a85c3bd5 ("drm/i915: Flush pending interrupt following a GPU reset")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Jeff McGee <jeff.mcgee@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180323101824.14645-1-chris@chris-wilson.co.uk

drm/i915/uc: Fetch uC firmware in init_early

We were fetching uC firmwares in separate uc_init_fw step, while
there is no reason why we can't fetch them during init_early.
This will also simplify upcoming patches, as size of the firmware
may be used for register initialization.

Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Michal Winiarski <michal.winiarski@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180323123451.59244-2-michal.wajdeczko@intel.com

drm/i915: Reorder early initialization

In upcoming patch, we want to perform more actions in early
initialization of the uC. This reordering will help resolve
new dependencies that will be introduced by future patch.

v2: s/i915_gem_load_init/i915_gem_init_early (Chris)
v3: s/i915_gem_load_cleanup/i915_gem_cleanup_early (Michal)

Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180323123451.59244-1-michal.wajdeczko@intel.com

drm/i915/guc: Fix null pointer dereference when GuC FW is not available

If GuC firmware is not available on the system and we load i915 with enable
GuC, then we hit this null pointer dereference issue:

[   71.098873] BUG: unable to handle kernel NULL pointer dereference at 0000000000000008
[   71.098938] IP: intel_uc_fw_upload+0x1f/0x360 [i915]
[   71.098947] PGD 0 P4D 0
[   71.098956] Oops: 0000 [#1] PREEMPT SMP PTI
[   71.098965] Modules linked in: i915(O+) netconsole x86_pkg_temp_thermal intel_powerclamp coretemp crct10dif_pclmul crc32_pclmul ghash_clmulni_intel mei_me i2c_i801 prime_numbers mei [last unloaded: i915]
[   71.099005] CPU: 2 PID: 1167 Comm: insmod Tainted: G     U  W  O     4.16.0-rc1+ #337
[   71.099018] Hardware name: /NUC6i5SYB, BIOS SYSKLi35.86A.0065.2018.0103.1000 01/03/2018
[   71.099077] RIP: 0010:intel_uc_fw_upload+0x1f/0x360 [i915]
[   71.099087] RSP: 0018:ffffc90000417aa0 EFLAGS: 00010282
[   71.099097] RAX: 0000000000000000 RBX: ffff88084cad12f8 RCX: ffffffffa03e9357
[   71.099108] RDX: 0000000000000002 RSI: ffffffffa034dba0 RDI: ffff88084cad12f8
[   71.099118] RBP: 0000000000000002 R08: ffff88085344ca90 R09: 0000000000000001
[   71.099128] R10: 0000000000000000 R11: 0000000000000000 R12: ffff88084cad0000
[   71.099139] R13: ffffffffa034dba0 R14: 00000000fffffff5 R15: ffff88084cad12b0
[   71.099151] FS:  00007f7f24ae2740(0000) GS:ffff88085e200000(0000) knlGS:0000000000000000
[   71.099162] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   71.099171] CR2: 0000000000000008 CR3: 0000000855f48001 CR4: 00000000003606e0
[   71.099182] Call Trace:
[   71.099246]  intel_uc_init_hw+0xc8/0x520 [i915]
[   71.099303]  i915_gem_init_hw+0x11f/0x2d0 [i915]
[   71.099364]  i915_gem_init+0x2b9/0x640 [i915]
[   71.099413]  i915_driver_load+0xb74/0x1110 [i915]
[   71.099462]  i915_pci_probe+0x2e/0x90 [i915]
[   71.099476]  pci_device_probe+0xa1/0x130
[   71.099488]  driver_probe_device+0x302/0x470
[   71.099502]  __driver_attach+0xb9/0xe0
[   71.099513]  ? driver_probe_device+0x470/0x470
[   71.099525]  ? driver_probe_device+0x470/0x470
[   71.099538]  bus_for_each_dev+0x64/0x90
[   71.099550]  bus_add_driver+0x164/0x260
[   71.099561]  ? 0xffffffffa04d6000
[   71.099572]  driver_register+0x57/0xc0
[   71.099582]  ? 0xffffffffa04d6000
[   71.099593]  do_one_initcall+0x3b/0x160
[   71.099606]  ? kmem_cache_alloc_trace+0x1c3/0x2a0
[   71.099621]  do_init_module+0x5b/0x1f9
[   71.099635]  load_module+0x2467/0x2a70
[   71.099654]  ? SyS_finit_module+0xbd/0xe0
[   71.099668]  SyS_finit_module+0xbd/0xe0
[   71.099682]  do_syscall_64+0x73/0x1c0
[   71.099694]  entry_SYSCALL_64_after_hwframe+0x26/0x9b
[   71.099706] RIP: 0033:0x7f7f23fb40d9
[   71.099717] RSP: 002b:00007ffda7d67ed8 EFLAGS: 00000246 ORIG_RAX: 0000000000000139
[   71.099734] RAX: ffffffffffffffda RBX: 000055f96e2a8870 RCX: 00007f7f23fb40d9
[   71.099748] RDX: 0000000000000000 RSI: 000055f96e2a8260 RDI: 0000000000000003
[   71.099763] RBP: 000055f96e2a8260 R08: 0000000000000000 R09: 00007ffda7d68088
[   71.099777] R10: 0000000000000003 R11: 0000000000000246 R12: 0000000000000000
[   71.099791] R13: 000055f96e2a8830 R14: 0000000000000000 R15: 000055f96e2a8260
[   71.099810] Code: 00 00 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 41 55 41 54 49 89 f5 55 53 48 c7 c1 57 93 3e a0 48 8b 47 10 48 89 fb 4c 8b 07 <48> 8b 68 08 8b 47 28 85 c0 74 15 83 f8 01 48 c7 c1 5b 93 3e a0
[   71.100004] RIP: intel_uc_fw_upload+0x1f/0x360 [i915] RSP: ffffc90000417aa0
[   71.100020] CR2: 0000000000000008
[   71.100031] ---[ end trace d8ac93c30ceff5b2 ]--

Fixes: 6b0478fb722a ("drm/i915: Implement dynamic GuC WOPCM offset and size calculation")
v2: don't assume it is always GuC FW (Michal)
v3: added a new variable to avoid exceeding the number of characters in the
line (Michal)

Signed-off-by: Piotr Piórkowski <piotr.piorkowski@intel.com>
Reported-by: Radoslaw Szwichtenberg <radoslaw.szwichtenberg@intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Jackie Li <yaodong.li@intel.com>
Cc: Radoslaw Szwichtenberg <radoslaw.szwichtenberg@intel.com>
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: Jackie Li <yaodong.li@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180323112319.16293-1-piotr.piorkowski@intel.com

drm/i915: Don't spew errors when resetting HDMI scrambling/bit clock ratio fails

When we're disabling the HDMI link we try to reset the scrambling and
TMDS bit clock ratio back to the default values. This will fail if the
sink has already been disconnected. Thus we should not print an error
message when resetting the scrambling/TMDS bit clock ratio fail during
disable. During enable we do want the error, and during disable we may
still want to know what happended for debug purposes so let's use
DRM_DEBUG_KMS() there.

v2: Remember them consts
v3: Go back to just one function and print the errors/debugs
    from callers (Shashank)

Cc: Shashank Sharma <shashank.sharma@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105644
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105655
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180322154707.22103-1-ville.syrjala@linux.intel.com
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>

drm/i915: Skip logging impossible slices

Log up to sseu->max_slices instead basing on ARRAY_SIZE since to avoid
printing impossible and empty slices for a platform.

Also compact slice total and slice mask into one log line.

Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180321103228.32205-1-tvrtko.ursulin@linux.intel.com

drm/i915: Avoid setting ring freq on invalid rps freqs

Looping through rps frequencies when both min and max are zero
ends up into an endless loop. This can happen during hardware
enablement.

Bail out early if rps frequencies are not correctly set yet.

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180320151734.11761-1-mika.kuoppala@linux.intel.com

drm/i915: Flush pending interrupt following a GPU reset

After resetting the GPU (or subset of engines), call synchronize_irq()
to flush any pending irq before proceeding with the cleanup. For a
device level reset, we disable the interupts around the reset, but when
resetting just one engine, we have to avoid such global disabling. This
leaves us open to an interrupt arriving for the engine as we try to
reset it. We already do try to flush the IIR following the reset, but we
have to ensure that the in-flight interrupt does not land after we start
cleaning up after the reset; enter synchronize_irq().

As it current stands, we very rarely, but fatally, see sequences such as:

    2.... 57964564us : execlists_reset_prepare: rcs0
    2.... 57964613us : execlists_reset: rcs0 seqno=424
    0d.h1 57964615us : gen8_cs_irq_handler: rcs0 CS active=1
    2d..1 57964617us : __i915_request_unsubmit: rcs0 fence 29:1056 <- global_seqno 1060
    2.... 57964703us : execlists_reset_finish: rcs0
    0..s. 57964705us : execlists_submission_tasklet: rcs0 awake?=1, active=0, irq-posted?=1

v2: Move the sync into the execlists reset handler so that we coordinate
the flush with disabling the interrupt handling and canceling the
pending interrupt.
v3: Just use synchronize_hardirq() to avoid the might_sleep(), we do not
yet have threaded-irq to worry about.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Jeff McGee <jeff.mcgee@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180322073533.5313-4-chris@chris-wilson.co.uk
Reviewed-by: Jeff McGee <jeff.mcgee@intel.com>

drm/i915: Use full serialisation around engine->irq_posted

Using engine->irq_posted for execlists, we are not always serialised by
the tasklet as we supposed. On the reset paths, the tasklet is disabled
and ignored. Instead, we manipulate the engine->irq_posted directly to
account for the reset, but if an interrupt fired before the reset and so
wrote to engine->irq_posted, that write may not be flushed from the
local CPU's cacheline until much later as the tasklet is already active
and so does not generate a mb(). To correctly serialise the interrupt
with reset, we need serialisation on the set_bit() itself.

And at last Mika can be happy.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
CC: Michel Thierry <michel.thierry@intel.com>
Cc: Jeff McGee <jeff.mcgee@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Jeff McGee <jeff.mcgee@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180322073533.5313-3-chris@chris-wilson.co.uk

drm/i915/selftests: Stress resets-vs-request-priority

Watch what happens if we try to reset with a queue of requests with
varying priorities -- that may need reordering or preemption across the
reset.

v2: Tweak priorities to avoid starving the hanging thread.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180322073533.5313-2-chris@chris-wilson.co.uk
Reviewed-by: Jeff McGee <jeff.mcgee@intel.com>

drm/i915/selftests: Include the trace as a debug aide

If we fail to reset the GPU in a timely fashion, dump the GEM trace so
that we can see what operations were in flight when the GPU got stuck.

v2: There's more than one timeout that deserves tracing!
v3: Silence checkpatch by not even using a product at all!

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Jeff McGee <jeff.mcgee@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180322074908.10838-1-chris@chris-wilson.co.uk

drm/i915: Remove local timeline var from submit/unsubmit

Both request_submit and request_unsubmit deal with transferring the
request from the client's timeline onto the execution timeline and back
again. As both functions deal with a pair of timeline's, using a
shorthand for just one of them is slightly confusing, especially as the
different functions use the shorthand for the alternate timeline.
Instead, use the full version of each timeline so it should be easier to
keep track of the transfer between the request/client and the engine.

v2: Refactor the common lock+list_move
v3: Be clear we require the other timeline list to be locked as well.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180322131034.6036-1-chris@chris-wilson.co.uk

drm/i915: Fix tracing of submit seqno

We pre-increment the timeline->seqno when handing it to the request,
make sure the GEM_TRACE takes this into account. Otherwise, it appears
that we go backwards over a preemption point:

1d..1 157681077us : __i915_request_unsubmit: vcs0 fence 75e:3 <- global_seqno 17
0d.s1 157681113us : __i915_request_submit: vcs0 fence 75e:3 -> global_seqno 16

Fixes: d9b13c4dde6c ("drm/i915: Trace GEM steps between submit and wedging")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180322110059.4467-1-chris@chris-wilson.co.uk

drm/i915/psr: Remove open-coded PSR AUX transactions for SKL+

HSW and BDW have SRD_AUX_{CTL, STATUS} registers that the driver needs to
setup for the HW to use whenever exiting PSR. SKL+ hardware use hardcoded
values for the same and do not need any registers to be setup. So, use
drm_dp_dpcd_writeb() for a one-time write during PSR enable and setup the
PSR aux registers on HSW and BDW for later use by HW.

We also end up writing to reserved bits in SRD_AUX_CTL by reusing
intel_dp->get_aux_send_ctl() for HSW and BDW, fix this.

Since the AUX register setup is source side programming, move the call
to enable_source() from enable_sink().

Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Jose Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180313034646.3721-2-dhinakaran.pandiyan@intel.com

drm/i915/psr: Move PSR aux setup to it's own function.

Non-functional change useful for the following patch.

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180313034646.3721-1-dhinakaran.pandiyan@intel.com

drm/i915/execlists: Use a locked clear_bit() for synchronisation with interrupt

We were relying on the uncached reads when processing the CSB to provide
ourselves with the serialisation with the interrupt handler (so we could
detect new interrupts in the middle of processing the old one). However,
in commit 767a983ab255 ("drm/i915/execlists: Read the context-status HEAD
from the HWSP") those uncached reads were eliminated (on one path at
least) and along with them our serialisation. The result is that we
would very rarely miss notification of a new interrupt and leave a
context-switch unprocessed, hanging the GPU.

Fixes: 767a983ab255 ("drm/i915/execlists: Read the context-status HEAD from the HWSP")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180321091027.21034-1-chris@chris-wilson.co.uk

drm/i915/guc: Unify parameters of public CT functions

There is no need to mix parameter types in public CT functions
as we can always accept intel_guc_ct.

v2: fix 'Return' doc, s/dev_priv/i915 (Sagar)

Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180320162020.38672-1-michal.wajdeczko@intel.com

drm/i915/guc: Handle GuC log flush event in dedicated function

We already try to keep all GuC log related code in separate file,
handling flush event should be placed there too. This will also
allow future code reuse.

v2: rebased

Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Michal Winiarski <michal.winiarski@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180319125049.48932-1-michal.wajdeczko@intel.com

drm/i915/guc: Move enable/disable msg functions to GuC header

While today we are modifying GuC enabled msg mask only in GuC
log, this code should be defined as generic GuC to allow future
code reuse.

Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Michal Winiarski <michal.winiarski@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180320181419.35576-3-michal.wajdeczko@intel.com

drm/i915/guc: Drop union guc_log_control

Usually we use shift/mask macros for bit field definitions.
Union guc_log_control was not following that pattern.

Additional bonus:

add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-25 (-25)
Function                                     old     new   delta
intel_guc_log_level_set                      388     363     -25

v2: prevent out-of-range verbosity (MichalWi)

Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Michal Winiarski <michal.winiarski@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Reviewed-by: MichaĹ Winiarski <michal.winiarski@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180320181419.35576-2-michal.wajdeczko@intel.com

drm/i915/guc: Unify naming of private GuC action functions

We should avoid using guc_log prefix for functions that don't
operate on GuC log, but rather request action from the GuC.
Better to use guc_action prefix.

v2: rebase + naming compromise
v3: rebase

Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Michal Winiarski <michal.winiarski@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180320181419.35576-1-michal.wajdeczko@intel.com

drm/i915/huc: Check HuC status in dedicated function

We try to keep all HuC related code in dedicated file.
There is no need to peek HuC register directly during
handling getparam ioctl.

Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180314200429.40132-1-michal.wajdeczko@intel.com

drm/i915/icl: Added ICL 11 slice, subslice and EU fuse detection

This patch adds support to detect ICL, slice, subslice and EU fuse
settings.

Add addresses for ICL 11 slice, subslice and EU fuses registers.
These register addresses are the same as previous platforms but the
format and / or the meaning of the information is different. Therefore
Gen11 defines for these registers are added.

Bspec: 9731
Bspec: 20643
Bspec: 20673

v2: Update fusing information storage after introducing the new query
    uAPI (Lionel)

v3 (Oscar):
  - The maximum number of slices in ICL 11 is 1
  - The subslice disable fuse can potentially store information in
    all bits
  - GEN_MAX_SUBSLICES has to be increased to 8
  - Don't trust the slice enabled fuse outside the max number of
    expected slices
  - Indentation fix and some reordering and renaming of local
    variables

v4: Use single space after Cc tag

Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Kelvin Gardiner <kelvin.gardiner@intel.com>
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1521575121-9577-1-git-send-email-oscar.mateo@intel.com

drm/i915: Add control flags to i915_handle_error()

Not all callers want the GPU error to handled in the same way, so expose
a control parameter. In the first instance, some callers do not want the
heavyweight error capture so add a bit to request the state to be
captured and saved.

v2: Pass msg down to i915_reset/i915_reset_engine so that we include the
reason for the reset in the dev_notice(), superseding the earlier option
to not print that notice.
v3: Stash the reason inside the i915->gpu_error to handover to the direct
reset from the blocking waiter.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jeff McGee <jeff.mcgee@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180320100449.1360-2-chris@chris-wilson.co.uk

drm/i915: Specify which engines to reset following semaphore/event lockups

If the GPU is stuck waiting for an event or for a semaphore, we need to
reset the GPU in order to recover. We have to tell the reset routine
which engines we want reset, but we were still using the old interface
and declaring it as "not-fatal".

Fixes: 14b730fcb8d9 ("drm/i915/tdr: Prepare error handler to accept mask of hung engines")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180320100449.1360-1-chris@chris-wilson.co.uk

drm/i915/guc: Don't try to enable GuC logging when we're not using GuC

When changing the default values for guc_log_level, we accidentally left
the log enabled on non-guc platforms. Let's fix that.

v2: Define the levels used and remove (now obsolete) comments (Chris)
v3: Use "IS" rather than "TO" for booleans (Chris)

Fixes: 9605d1ce7c6b ("drm/i915/guc: Default to non-verbose GuC logging")
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180320115517.20423-1-michal.winiarski@intel.com

drm/i915/icl: Update subslice define for ICL 11

ICL 11 has a greater number of maximum subslices. This patch
reflects this.

v2: GEN11 updates to MCR_SELECTOR (Oscar)
v3: Copypasta error in the new defines (Lionel)

Bspec: 21139
BSpec: 21108

Signed-off-by: Kelvin Gardiner <kelvin.gardiner@intel.com>
Reviewed-by: Oscar Mateo <oscar.mateo@intel.com> (v1)
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> (v1)
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180316121456.11577-3-mika.kuoppala@linux.intel.com
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>

drm/i915/icl: Enable the extra video decode and enhancement boxes for Icelake 11

Icelake 11 has one vebox and two vdboxes (0 and 2).

Bspec: 21140

v2: Split out in two (Daniele)

Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180316121456.11577-2-mika.kuoppala@linux.intel.com
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>

drm/i915/icl: Check for fused-off VDBOX and VEBOX instances

In Gen11, the Video Decode engines (aka VDBOX, aka VCS, aka BSD) and the
Video Enhancement engines (aka VEBOX, aka VECS) could be fused off. Also,
each VDBOX and VEBOX has its own power well, which only exist if the
related engine exists in the HW.

Unfortunately, we have a Catch-22 situation going on: we need the blitter
forcewake to read the register with the fuse info, but we cannot initialize
the forcewake domains without knowin about the engines present in the HW.
We workaround this problem by allowing the initialization of all forcewake
domains and then pruning the fused off ones, as per the fuse information.

Bspec: 20680

v2: We were shifting incorrectly for vebox disable (Vinay)

v3: Assert mmio is ready and warn if we have attempted to initialize
    forcewake for fused-off engines (Paulo)

v4:
  - Use INTEL_GEN in new code (Tvrtko)
  - Shorter local variable (Tvrtko, Michal)
  - Keep "if (!...) continue" style (Tvrtko)
  - No unnecessary BUG_ON (Tvrtko)
  - WARN_ON and cleanup if wrong mask (Tvrtko, Michal)
  - Use I915_READ_FW (Michal)
  - Use I915_MAX_VCS/VECS macros (Michal)

v5: Rebased by Rodrigo fixing conflicts on top of:
    "drm/i915: Simplify intel_engines_init"

v6: Fix v5. Remove info->num_rings. (by Oscar)

v7: Rebase (Rodrigo).

v8:
  - s/intel_device_info_fused_off_engines/
    intel_device_info_init_mmio (Chris)
  - Make vdbox_disable & vebox_disable local variables (Chris)

v9:
  - Move function declaration to intel_device_info.h (Michal)
  - Missing indent in bit fields definitions (Michal)
  - When RC6 is enabled by BIOS, the fuse register cannot be read until
    the blitter powerwell is awake. Shuffle where the fuse is read, prune
    the forcewake domains after the fact and change the commit message
    accordingly (Vinay, Sagar, Chris).

v10:
  - Improved commit message (Sagar)
  - New line in header file (Sagar)
  - Specify the message in fw_domain_reset applies to ICL+ (Sagar)

Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Vinay Belgaumkar <vinay.belgaumkar@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180316121456.11577-1-mika.kuoppala@linux.intel.com
[Mika: soothe checkpatch on commit msg]
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>

drm/i915: Select STACKDEPOT for DRM_I915_DEBUG

select in Kconfig isn't recursive, we need to select the stuff our
selects select, too. Fix that.

Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180320125009.2305-1-daniel.vetter@ffwll.ch

drm/i915: Trim error mask to known engines

For the convenience of userspace passing in an arbitrary reset mask,
remove unknown engines from the set of engines that are to be reset.
This means that we always follow a per-engine reset with a full-device
reset when userspace writes -1 into debugfs/i915_wedged.

Reported-by: Michał Winiarski <michal.winiarski@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180316215001.12391-1-chris@chris-wilson.co.uk
Reviewed-by: Michel Thierry <michel.thierry@intel.com>

drm/i915: Prefer memset64() when filling the iomap

As the ringbuffer may exist inside stolen memory, our access to it may
be via the GTT iomap. This implies we may only have WC access for which
the conventional memset() substitution of rep stos performs very badly,
so switch to the rep mov[dq] variants when available.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180319123528.28249-1-chris@chris-wilson.co.uk

drm/i915/guc: Demote GuC error messages

We're using those functions in selftests, and the callers are expected
to do the error handling anyways. Let's demote all GuC actions and
doorbell creation to DEBUG_DRIVER.

Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180319095348.9716-12-michal.winiarski@intel.com

drm/i915/guc: Default to non-verbose GuC logging

Now that we've decoupled logging from relay, GuC log level is only
controlling the GuC behavior - there shouldn't be any impact on i915
behaviour. We're only going to see a single extra interrupt when log
will get half full.
That, and the fact that we're seeing igt/gem_exec_nop/basic-series
failing with non-verbose logging being disabled.

v2: Bring back the "auto" guc_log_level, now that we fixed the log

Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180319095348.9716-11-michal.winiarski@intel.com

drm/i915/guc: Allow user to control default GuC logging

While both naming and actual log enable logic in GuC interface are
confusing, we can simply expose the default log as yet another log
level.
GuC logic aside, from i915 point of view we now have the following GuC
log levels:
0 Log disabled
1 Non-verbose log
2-5 Verbose log

v2: Adjust naming after rebase.
v3: Fixed the log_level logic error introduced on rebase.

Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180319095348.9716-10-michal.winiarski@intel.com

drm/i915/guc: Don't print out relay statistics when relay is disabled

If nobody has enabled the relay, we're not comunicating with GuC, which
means that the stats don't have any meaning. Let's also remove interrupt
counter and tidy the debugfs formatting.

v2: Correct stats accounting (Sagar)
v3: Corrected one more error in stats accounting, move relay_enabled (Sagar)

Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180319095348.9716-9-michal.winiarski@intel.com

drm/i915/guc: Always print log stats in i915_guc_info when using GuC

While some of the content in this file is related to GuC submission
only, that's not the case with log related statistics.

Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180319095348.9716-8-michal.winiarski@intel.com

drm/i915/guc: Get rid of GuC log runtime

Runtime is not a very good name. Let's also move counting relay
overflows inside relay struct.

v2: Rename things rather than remove the struct (Chris)

Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180319095348.9716-7-michal.winiarski@intel.com

drm/i915/guc: Move check for fast memcpy_wc to relay creation

We only need those fast memcpy_wc when we're using relay to read
continuous GuC log. Let's prevent the user from creating a relay if we
know we won't be able to keep up with GuC.

v2: Adjust the return value (Michał)

Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180319095348.9716-6-michal.winiarski@intel.com

drm/i915/guc: Split relay control and GuC log level

Those two concepts are really separate. Since GuC is writing data into
its own buffer and we even provide a way for userspace to read directly
from it using i915_guc_log_dump debugfs, there's no real reason to tie
log level with relay creation.
Let's create a separate debugfs, giving userspace a way to create a
relay on demand, when it wants to read a continuous log rather than a
snapshot.

v2: Don't touch guc_log_level on relay creation error, adjust locking
    after rebase, s/dev_priv/i915, pass guc to file->private_data (Sagar)
    Use struct_mutex rather than runtime.lock for set_log_level
v3: Tidy ordering of definitions (Sagar)

Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180319095348.9716-5-michal.winiarski@intel.com

drm/i915/guc: Flush directly in log unregister

Having both guc_flush_logs and guc_log_flush functions is confusing.
While we could just rename things, guc_flush_logs implementation is
quite simple. Let's get rid of it and move its content to unregister.

v2: s/dev_priv/i915 (Sagar)

Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180319095348.9716-4-michal.winiarski@intel.com

drm/i915/guc: Merge log relay file and channel creation

We have all the information we need at relay_open call time.
Since there's no reason to split the process into relay_open and
relay_late_setup_files, let's remove the extra code.

v2: Remove obsoleted comments (Sagar)
v3: There was one obsolete comment left (Sagar)

Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180319095348.9716-3-michal.winiarski@intel.com

drm/i915/guc: Log runtime should consist of both mapping and relay

Currently, we're treating relay and mapping of GuC log as a separate
concepts. We're also using inconsistent locking, sometimes using
relay_lock, sometimes using struct mutex.
Let's correct that. Anything touching the runtime is now serialized
using runtime.lock, while we're still using struct mutex as inner lock
for mapping.
We're still racy in setting the log level - but we'll take care of that
in the following patches.

v2: Tidy locking (Sagar)
v3: Remove obsoleted comment (Sagar)

Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180319095348.9716-2-michal.winiarski@intel.com

drm/i915/guc: Keep GuC interrupts enabled when using GuC

The GuC log contains a separate space used for crash dump.
We even get a separate notification for it. While we're not handling
crash differently yet, it makes sense to decouple the two right now to
simplify the following patches.

v2: Move guc_log_flush_irq_disable up to avoid movement in following
    patches (Sagar).
v3: s/guc_log_flush_irq_*/guc_flush_log_msg_*, rebase after mass rename

Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: Sagar Arun Kamble <sagar.a.kamble@intel.com> (v2)
Reviewed-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180319095348.9716-1-michal.winiarski@intel.com

drm/i915/dp: Write to SET_POWER dpcd to enable MST hub.

If bios sets up an MST output and hardware state readout code sees this is
an SST configuration, when disabling the encoder we end up calling
->post_disable_dp() hook instead of the MST version. Consequently, we write
to the DP_SET_POWER dpcd to set it D3 state. Further along when we try
enable the encoder in MST mode, POWER_UP_PHY transaction fails to power up
the MST hub. This results in continuous link training failures which keep
the system busy delaying boot. We could identify bios MST boot discrepancy
and handle it accordingly but a simple way to solve this is to write to the
DP_SET_POWER dpcd for MST too.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105470
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reported-by: Laura Abbott <labbott@redhat.com>
Cc: stable@vger.kernel.org
Fixes: 5ea2355a100a ("drm/i915/mst: Use MST sideband message transactions for dpms control")
Tested-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180314054825.1718-1-dhinakaran.pandiyan@intel.com

drm/i915: Kill the remaining CHV HBR2 leftovers

AFAIK CHV was supposed to have HBR2 originally, but in the end the feature
was dropped. We still have some code leftovers from those early days.
Eliminate them.

The extra bit for the training pattern seems to be dead in the hardware.
I can set it (in fact I can set almost any reserved bit in the
registers) but it doesn't seem to interfere with the operation of the
hardware. Either that or I'm very lucky that my displays complete link
training with the incorrect pattern being sent out.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180302095656.19662-1-ville.syrjala@linux.intel.com
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>

i915: Re-use DEFINE_SHOW_ATTRIBUTE() macro

...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.

Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180316141213.38774-1-andriy.shevchenko@linux.intel.com

drm/i915: Don't initialize plane_to_crtc_mapping[] on SKL+

We don't use the enum i9xx_plane_id namespace on SKL+ anymore, so
do not initialize the related plane_to_crtc_mapping[] table either.

Actually the only remaining user of that table is the pre-g4x
watermark code, but no harm in initializing the table on all
pre-SKL platforms.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180305174122.17273-1-ville.syrjala@linux.intel.com
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>

drm/i915/stolen: Deduce base of reserved portion as top-size on vlv

On Valleyview, the HW deduces the base of the reserved portion of stolen
memory as being (top - size) and the address field within
GEN6_STOLEN_RESERVED is set to 0. Add yet another GEN6_STOLEN_RESERVED
reader to cope with the subtly different path required for vlv.

v2: Avoid using reserved_base = reserved_size = 0 as the invalid
condition as that typically falls outside of the stolen region,
provoking a consistency error.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180312165206.31772-3-chris@chris-wilson.co.uk

drm/i915/stolen: Checkpatch cleansing

In the next patch, we will introduce a new vlv_get_stolen_reserved, so
before we do, make sure checkpatch is happy with the surrounding code.
Sneak in some debug output while we are here.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180312165206.31772-2-chris@chris-wilson.co.uk
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>

drm/i915/stolen: Switch from DEBUG_KMS to DEBUG_DRIVER

i915_gem_stolen is an allocator for the reserved portion of memory
("stolen" from the system by the BIOS). It is not tied to KMS but
central to the driver, so prefer DRM_DEBUG_DRIVER.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180312165206.31772-1-chris@chris-wilson.co.uk

drm/i915: Stop engines when declaring the machine wedged

If we fail to reset the GPU, we declare the machine wedged. However, the
GPU may well still be running in the background with an in-flight
request. So despite our efforts in cleaning up the request queue and
faking the breadcrumb in the HWSP, the GPU may eventually write the
in-flght seqno there breaking all of our assumptions and throwing the
driver into a deep turmoil, wedging beyond wedged.

To avoid this we ideally want to reset the GPU. Since that has already
failed, make sure the rings have the stop bit set instead. This is part
of the normal GPU reset sequence, but that is actually disabled by
igt/gem_eio to force the wedged state. If we assume the worst, we must
poke at the bit again before we give up.

v2: Move the intel_gpu_reset() from set-wedged in the reset error path
into i915_gem_set_wedged() itself. Even if the reset fails (e.g. if it is
disabled by gem_eio), it still tries to make sure the engines are
stopped. For i915_gem_set_wedged() callers from outside of i915_reset(),
this should make sure the GPU is disabled while the driver is marked as
being wedged.

Testcase: igt/gem_eio
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180315151015.22741-1-chris@chris-wilson.co.uk

drm/i915: Trace GEM steps between submit and wedging

We still have an odd race with wedging/unwedging as shown by igt/gem_eio
that defies expectations. Add some more trace_printks to try and
visualize the flow over the precipice.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180315131451.4060-1-chris@chris-wilson.co.uk

drm/i915/guc: Fix build break on config without DEBUG_FS

In commit 56b9a8b08387 ("drm/i915/guc: Update syntax of GuC
log functions") we accidentally removed debugfs.h header
where needed stub functions were defined.

Reported-by: Mike Lothian <mike@fireburn.co.uk>
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Mike Lothian <mike@fireburn.co.uk>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180315152848.40476-1-michal.wajdeczko@intel.com

drm/i915/guc: Update syntax of GuC log functions

We moved GuC log related data and code to separate files and
definition but we didn't change functions syntax to follow
object-verb pattern. Let's fix that before we continue with
next round of code refactoring.

v2: rebased

Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Michal Winiarski <michal.winiarski@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180314144539.11152-1-michal.wajdeczko@intel.com
[ickle: checkpatch booleans]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915: Split GPU commands definitions into separate header

We should not mix MMIO with MI_INSTR definitions.

v2: sanitize comment, change include order (Chris)

Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180313124109.39216-1-michal.wajdeczko@intel.com
Link: https://patchwork.freedesktop.org/patch/msgid/20180313231920.6932-1-chris@chris-wilson.co.uk

drm/i915: move gen8 irq shifts to intel_lrc.c

The only usage outside the intel_lrc.c file is in the ringbuffer
init, but the irq mask calculated there is then overwritten for
all engines that have a non-zero shift, so we can drop it.

This change is not aimed at code saving but at removing from
intel_engines information that does not apply to all gens that have
the engine. When checking without the temporary WARN_ON, code size
is basically unchanged.

v2: make the irq_shifts array static const
v3: rebase, move irq_shifts array to logical_ring_default_irqs
v4: move array inside the if and use u8 for it (Chris)

Suggested-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180314182653.26981-4-daniele.ceraolospurio@intel.com

drm/i915: use engine->irq_keep_mask when resetting irqs

The "reset" value and the "keep" value are the same.
While we are here, add a TODO for gen11 interrupt reset

Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180314182653.26981-3-daniele.ceraolospurio@intel.com

drm/i915: add a selftest for the mmio_bases table

Check that the entries are in reverse gen order and that all entries
with gen > 0 have an mmio base set.

v2: loop forward, simplify logic, use i915_subtests (Chris)

Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180314182653.26981-2-daniele.ceraolospurio@intel.com

drm/i915: store all mmio bases in intel_engines

The mmio bases we're currently storing in the intel_engines array are
only valid for a subset of gens, so we need to ignore them and use
different values in some cases. Instead of doing that, we can have a
table of [starting gen, mmio base] pairs for each engine in
intel_engines and select the correct one based on the gen we're running
on in a consistent way.

v2: document that the list goes in reverse order, update starting gen
    for render (Chris)

v3: starting gen for render back to 1 to make our life easier with
    selftests (Chris)

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> #v2
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180314182653.26981-1-daniele.ceraolospurio@intel.com

drm/i915/cnl: Kill _MMIO_PORT6 macro

This patch replaces use of remaining _MMIO_PORT6 macro and removes the
macro.

Changes Since V1:
 - Rebase

Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180314080653.9444-3-mahesh1.kumar@intel.com

drm/i915/cnl; Add macro to get PORT_TX register

This patch creates a new macro to get PORT_TX register for any given DW.
This removes the need of defining register address for each port & DW.

Changes since V1:
 - Use underscope prefix, as macro isn't returning an mmio reg(Lucas)
 - Merge patch 1 & 2 of the series
Changes since V2:
 - remove _MMIO_PORT6_LN macro (Rodrigo)

Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180314080653.9444-2-mahesh1.kumar@intel.com

drm/i915/pmu: Work around compiler warnings on some kernel configs

Arnd Bergman reports:
"""
The conditional spinlock confuses gcc into thinking the 'flags' value
might contain uninitialized data:

drivers/gpu/drm/i915/i915_pmu.c: In function '__i915_pmu_event_read':
arch/x86/include/asm/paravirt_types.h:573:3: error: 'flags' may be used uninitialized in this function [-Werror=maybe-uninitialized]

The code is correct, but it's easy to see how the compiler gets confused
here. This avoids the problem by pulling the lock outside of the function
into its only caller.
"""

On deeper look it seems this is caused by paravirt spinlocks
implementation when CONFIG_PARAVIRT_DEBUG is set, which by being
complicated, manages to convince gcc locked parameter can be changed
externally (impossible).

Work around it by removing the conditional locking parameters altogether.
(It was never the most elegant code anyway.)

Slight penalty we now pay is an additional irqsave spin lock/unlock cycle
on the event enable path. But since enable is not a fast path, that is
preferrable to the alternative solution which was doing MMIO under irqsave
spinlock.

Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 1fe699e30113 ("drm/i915/pmu: Fix sleep under atomic in RC6 readout")
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: David Airlie <airlied@linux.ie>
Cc: intel-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180314080535.17490-1-tvrtko.ursulin@linux.intel.com

drm/i915: Check rq->timeline before deference

Not only is the context suspect to disappearing, but so is it's
timeline. Under a lockless inspection of the requests for
debugging from intel_engine_dump(), the context may already have been
freed and we have to check before chasing the dangling pointer.

[28033.681755] Modules linked in: vgem snd_hda_codec_hdmi snd_hda_codec_realtek snd_hda_codec_generic x86_pkg_temp_thermal intel_powerclamp coretemp snd_hda_intel crct10dif_pclmul crc32_pclmul snd_hda_codec snd_hwdep snd_hda_core ghash_clmulni_intel snd_pcm mei_me mei i915 r8169 mii prime_numbers i2c_hid
[28033.681796] CPU: 3 PID: 3058 Comm: gem_exec_schedu Tainted: G     U           4.16.0-rc5+ #9
[28033.681804] Hardware name: Acer Aspire E5-575G/Ironman_SK  , BIOS V1.12 08/02/2016
[28033.681834] RIP: 0010:print_request+0x2b/0xb0 [i915]
[28033.681840] RSP: 0018:ffffc90004afbc18 EFLAGS: 00010202
[28033.681847] RAX: 6b6b6b6b6b6b6b6b RBX: ffff8801921b5a40 RCX: 0000000000000006
[28033.681854] RDX: ffffc90004afbc60 RSI: ffff8801921b5a40 RDI: 0000000000000004
[28033.681861] RBP: ffffc90004afbd80 R08: 0000000000000000 R09: 0000000000000001
[28033.681868] R10: ffffc90004afbbd0 R11: ffffc90004afbc73 R12: ffffc90004afbc60
[28033.681875] R13: ffffc90004afbd80 R14: ffff8801d40ec670 R15: ffff8801921b5a40
[28033.681883] FS:  00007fbba5f6c8c0(0000) GS:ffff8801e8400000(0000) knlGS:0000000000000000
[28033.681891] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[28033.681897] CR2: 00007fbba5f8f000 CR3: 00000001b2efa002 CR4: 00000000003606e0
[28033.681904] Call Trace:
[28033.681932]  intel_engine_print_registers+0x6a7/0x930 [i915]
[28033.681962]  intel_engine_dump+0x30d/0x740 [i915]
[28033.681971]  ? seq_printf+0x3a/0x50
[28033.681995]  i915_engine_info+0xb8/0xe0 [i915]
[28033.682003]  ? drm_get_color_range_name+0x20/0x20
[28033.682010]  seq_read+0xe1/0x440
[28033.682018]  full_proxy_read+0x51/0x80
[28033.682025]  __vfs_read+0x21/0x130
[28033.682031]  ? do_sys_open+0x134/0x220
[28033.682037]  ? kmem_cache_free+0x177/0x2b0
[28033.682043]  vfs_read+0xa1/0x150
[28033.682049]  SyS_read+0x40/0xa0
[28033.682055]  do_syscall_64+0x6b/0x1b0
[28033.682063]  entry_SYSCALL_64_after_hwframe+0x42/0xb7
[28033.682069] RIP: 0033:0x7fbba4655d11
[28033.682074] RSP: 002b:00007ffd8c49da58 EFLAGS: 00000246 ORIG_RAX: 0000000000000000
[28033.682082] RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007fbba4655d11
[28033.682089] RDX: 000000000000003f RSI: 00005647bfbfc260 RDI: 0000000000000006
[28033.682096] RBP: 000000000000003f R08: 00000000ffffffff R09: 0000000000000000
[28033.682104] R10: 0000000000000000 R11: 0000000000000246 R12: 00005647bfbfc260
[28033.682111] R13: 0000000000000006 R14: 0000000000000000 R15: 00005647bfbfc260
[28033.682119] Code: 41 55 41 54 49 89 d4 55 53 48 89 fd 48 8b 86 c8 00 00 00 48 8b 3d d6 1e 14 e2 48 89 f3 48 2b be a8 02 00 00 48 8b 80 b0 00 00 00 <4c> 8b 68 18 e8 bc 80 02 e1 8b 8b 70 02 00 00 8b b3 28 02 00 00
[28033.682206] RIP: print_request+0x2b/0xb0 [i915] RSP: ffffc90004afbc18

Reported-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180314101630.8933-1-chris@chris-wilson.co.uk

drm/i915/guc: Check the locking status of GuC WOPCM registers

GuC WOPCM registers are write-once registers. Current driver code accesses
these registers without checking the accessibility to these registers which
will lead to unpredictable driver behaviors if these registers were touch
by other components (such as faulty BIOS code).

This patch moves the GuC WOPCM registers updating code into intel_wopcm.c
and adds check before and after the update to GuC WOPCM registers so that
we can make sure the driver is in a known state after writing to these
write-once registers.

v6:
 - Made sure module reloading won't bug the kernel while doing
   locking status checking

v7:
 - Fixed patch format issues

v8:
 - Fixed coding style issue on register lock bit macro definition (Sagar)

v9:
 - Avoided to use redundant !! to cast uint to bool (Chris)
 - Return error code instead of GEM_BUG_ON for locked with invalid register
   values case (Sagar)
 - Updated guc_wopcm_hw_init to use guc_wopcm as first parameter (Michal)
 - Added code to set and validate the HuC_LOADING_AGENT_GUC bit in GuC
   WOPCM offset register based on the presence of HuC firmware (Michal)
 - Use bit fields instead of macros for GuC WOPCM flags (Michal)

v10:
 - Refined variable names, removed redundant comments (Joonas)
 - Introduced lockable_reg to handle the write once register write and
   propagate the write error to caller (Joonas)
 - Used lockable_reg abstraction to avoid locking bit check on generic
   i915_reg_t (Michal)
 - Added log message for error paths (Michal)
 - Removed hw_updated flag and only relies on real hardware status

v11:
 - Replaced lockable_reg with simplified function (Michal)
 - Used new macros for locking bits of WOPCM size/offset registers instead
   of using BIT(0) directly (Michal)
 - use intel_wopcm_init_hw() called from intel_gem_init_hw() to do GuC
   WOPCM register setup instead of calling from intel_uc_init_hw() (Michal)

v12:
 - Updated function kernel-doc to align with code changes (Michal)
 - Updated code to use wopcm pointer directly (Michal)

v13:
 - Updated the ordering of s-o-b/cc/r-b tags (Sagar)

BSpec: 10875, 10833

Signed-off-by: Jackie Li <yaodong.li@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com> (v11)
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> (v12)
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1520987574-19351-5-git-send-email-yaodong.li@intel.com

drm/i915: Add HuC firmware size related restriction for Gen9 and CNL A0

On CNL A0 and Gen9, there's a hardware restriction that requires the
available GuC WOPCM size to be larger than or equal to HuC firmware size.

This patch adds new verification code to ensure the available GuC WOPCM
size to be larger than or equal to HuC firmware size on both Gen9 and CNL
A0.

v6:
 - Extended HuC FW size check against GuC WOPCM size to all
   Gen9 and CNL A0 platforms

v7:
 - Fixed patch format issues

v8:
 - Renamed variables and functions to avoid ambiguity (Joonas)
 - Updated commit message and comments to be more comprehensive (Sagar)

v9:
 - Moved code that is not related to restriction check into a separate
   patch and updated the commit message accordingly (Sagar/Michal)
 - Avoided to call uc_get_fw_size for better layer isolation (Michal)

v10:
 - Shorten function names and reorganized size_check code to have clear
   isolation (Joonas)
 - Removed unnecessary comments (Joonas)

v11:
 - Fixed logic error in size check (Michal)

v12:
 - Add space between "HuC FW" and "(%uKiB)" in error message (Michal)

v13:
 - Updated the ordering of s-o-b/cc/r-b tags (Sagar)

BSpec: 10875

Signed-off-by: Jackie Li <yaodong.li@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: John Spotswood <john.a.spotswood@intel.com>
Cc: Jeff McGee <jeff.mcgee@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Sagar Arun Kamble <sagar.a.kamble@intel.com> (v8)
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com> (v11)
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> (v12)
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1520987574-19351-4-git-send-email-yaodong.li@intel.com

drm/i915: Add support to return CNL specific reserved WOPCM size

CNL has its specific reserved GuC WOPCM size for RC6 and other hardware
contexts.

This patch updates the code to return CNL specific reserved GuC WOPCM size
for RC6 and other hardware contexts so that the GuC WOPCM size can be
calculated correctly for CNL.

v9:
 - Created a new patch for these changes originally made in v8 4/6 patch of
   this series (Sagar/Michal)

v10:
 - Used if-else ladder to the returning of context sizes (Joonas)

v11:
 - Removed GUC_ prefix from context size macro (Michal)

v13:
  - Updated the ordering of s-o-b/cc/r-b tags (Sagar)

Bspec: 12690

Signed-off-by: Jackie Li <yaodong.li@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> (v9)
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com> (v11)
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> (v12)
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1520987574-19351-3-git-send-email-yaodong.li@intel.com

drm/i915: Implement dynamic GuC WOPCM offset and size calculation

Hardware may have specific restrictions on GuC WOPCM offset and size. On
Gen9, the value of the GuC WOPCM size register needs to be larger than the
value of GuC WOPCM offset register + a Gen9 specific offset (144KB) for
reserved GuC WOPCM. Fail to enforce such a restriction on GuC WOPCM size
will lead to GuC firmware execution failures. On the other hand, with
current static GuC WOPCM offset and size values (512KB for both offset and
size), the GuC WOPCM size verification will fail on Gen9 even if it can be
fixed by lowering the GuC WOPCM offset by calculating its value based on
HuC firmware size (which is likely less than 200KB on Gen9), so that we can
have a GuC WOPCM size value which is large enough to pass the GuC WOPCM
size check.

This patch updates the reserved GuC WOPCM size for RC6 context on Gen9 to
24KB to strictly align with the Gen9 GuC WOPCM layout. It also adds support
to verify the GuC WOPCM size aganist the Gen9 hardware restrictions. To
meet all above requirements, let's provide dynamic partitioning of the
WOPCM that will be based on platform specific HuC/GuC firmware sizes.

v2:
 - Removed intel_wopcm_init (Ville/Sagar/Joonas)
 - Renamed and Moved the intel_wopcm_partition into intel_guc (Sagar)
 - Removed unnecessary function calls (Joonas)
 - Init GuC WOPCM partition as soon as firmware fetching is completed

v3:
 - Fixed indentation issues (Chris)
 - Removed layering violation code (Chris/Michal)
 - Created separat files for GuC wopcm code  (Michal)
 - Used inline function to avoid code duplication (Michal)

v4:
 - Preset the GuC WOPCM top during early GuC init (Chris)
 - Fail intel_uc_init_hw() as soon as GuC WOPCM partitioning failed

v5:
 - Moved GuC DMA WOPCM register updating code into intel_wopcm.c
 - Took care of the locking status before writing to GuC DMA
   Write-Once registers. (Joonas)

v6:
 - Made sure the GuC WOPCM size to be multiple of 4K (4K aligned)

v8:
 - Updated comments and fixed naming issues (Sagar/Joonas)
 - Updated commit message to include more description about the hardware
   restriction on GuC WOPCM size (Sagar)

v9:
 - Minor changes variable names and code comments (Sagar)
 - Added detailed GuC WOPCM layout drawing (Sagar/Michal)
 - Refined macro definitions to be reader friendly (Michal)
 - Removed redundent check to valid flag (Michal)
 - Unified first parameter for exported GuC WOPCM functions (Michal)
 - Refined the name and parameter list of hardware restriction checking
   functions (Michal)

v10:
 - Used shorter function name for internal functions (Joonas)
 - Moved init-ealry function into c file (Joonas)
 - Consolidated and removed redundant size checks (Joonas/Michal)
 - Removed unnecessary unlikely() from code which is only called once
   during boot (Joonas)
 - More fixes to kernel-doc format and content (Michal)
 - Avoided the use of PAGE_MASK for 4K pages (Michal)
 - Added error log messages to error paths (Michal)

v11:
 - Replaced intel_guc_wopcm with more generic intel_wopcm and attached
   intel_wopcm to drm_i915_private instead intel_guc (Michal)
 - dynamic calculation of GuC non-wopcm memory start (a.k.a WOPCM Top
   offset from GuC WOPCM base) (Michal)
 - Moved WOPCM marco definitions into .c source file (Michal)
 - Exported WOPCM layout diagram as kernel-doc (Michal)

v12:
 - Updated naming, function kernel-doc to align with new changes (Michal)

v13:
 - Updated the ordering of s-o-b/cc/r-b tags (Sagar)
 - Corrected one tense error in comment (Sagar)
 - Corrected typos and removed spurious comments (Joonas)

Bspec: 12690

Signed-off-by: Jackie Li <yaodong.li@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Sujaritha Sundaresan <sujaritha.sundaresan@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: John Spotswood <john.a.spotswood@intel.com>
Cc: Oscar Mateo <oscar.mateo@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Sagar Arun Kamble <sagar.a.kamble@intel.com> (v8)
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> (v9)
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com> (v11)
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> (v12)
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1520987574-19351-2-git-send-email-yaodong.li@intel.com

drm/i915/guc: Rename guc_ggtt_offset to intel_guc_ggtt_offset

GuC related exported functions should start with "intel_guc_" prefix and
pass intel_guc as the first parameter since its GuC related. Current
guc_ggtt_offset() failed to follow this code convention and this is a
problem for future patches that needs to access intel_guc data to verify
the GGTT offset against the GuC WOPCM top.

This patch renames the guc_ggtt_offset to intel_guc_ggtt_offset and updates
the related code to pass intel_guc pointer to this function call, so that
we can have a unified coding style for GuC code and also enable the future
patches to get GuC related data from intel_guc to do the offset
verification. Meanwhile, this patch also moves the GUC_GGTT_TOP from
intel_guc_regs.h to intel_guc.h since it is not GuC register related
definition.

v8:
 - Fixed coding style issues and moved GUC_GGTT_TOP to intel_guc.h (Sagar)
 - Updated commit message to explain to reason and motivation to add
   intel_guc as the first parameter of intel_guc_ggtt_offset (Chris)

v9:
 - Fixed code alignment issue due to line break (Chris)

v10:
 - Removed unnecessary comments, redundant code and avoided reuse variable
   to avoid potential issues (Joonas)

v13:
 - Updated the ordering of s-o-b/cc/r-b tags (Sagar)

Signed-off-by: Jackie Li <yaodong.li@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Sagar Arun Kamble <sagar.a.kamble@intel.com> (v8)
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> (v9)
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com> (v11)
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> (v12)
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1520987574-19351-1-git-send-email-yaodong.li@intel.com

drm/i915/psr: Comment to clarify SRD_DEBUG is called PSR_MASK SKL+

What was called SRD_DEBUG(0x6F860) on HSW and BDW was renamed to PSR_MASK
SKL onwards, add a note next to the macro definition.
There is also a different PSR_DEBUG on SKL+ to add to the confusion.

Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180313040954.6289-1-dhinakaran.pandiyan@intel.com

drm/i915: Show GEM_TRACE when detecting a failed GPU idle

If we timeout waiting for the GPU to idle, something went seriously
wrong. We currently dump the engine state, but we can also dump the
ftrace buffer showing our last operations (when available).

In passing, note that since commit 559e040f1f08 ("drm/i915: Show the GPU
state when declaring wedged", we now show the engine state twice, once
in detecting the failed idle and then again on declaring wedged.

v2: ftrace_dump() takes a parameter specifying whether to dump all cpu
buffers or the local cpu's.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180309101114.1138-1-chris@chris-wilson.co.uk

drm/i915: Move CUR SURFLIVE definition to a better place.

No functional change. But let's keep definitions clean
and cursor related register definitions together.

v2: Fix caps x no caps on same reg. Change name to match
    original reg name. (by Ville).
    Also fix name on code s/surlive/surflive and on subject
    s/cur_surlife/cur surflive/.

Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180312210528.7905-1-rodrigo.vivi@intel.com

drm/i915/psr: Remove PSR active flag from debugfs

The flag becomes misleading with flips and cursor moves not modifying it's
state as HW takes care of exiting PSR (when HW tracking is enabled)

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180313044211.27105-1-dhinakaran.pandiyan@intel.com

drm/i915/psr: Use more PSR HW tracking.

So far we are using frontbuffer tracking for everything
and ignoring that PSR has a HW capable HW tracking for many
modern usages of GPU on Core platforms and newer Atom ones.

One reason for that is that we were trying to keep same
infrastructure in place for VLV/CHV than the rest of platforms.
But also because when this infrastructure was created
the front-buffer-tracking origin wasn't that good and stable
how it is today after Paulo reworked it to attend FBC cases.

However this PSR implementation without HW tracking died
on gen8LP. And newer platforms are starting to demand more HW
tracking specially with PSR2 cases in mind.

By disabling and re-enabling PSR totally every time we believe
someone is going to change the front buffer content we don't
allow PSR HW tracking to do this job and specially compromising
the whole idea of PSR2 case where the HW tracking detect only
the damaged area and do a partial screen update.

So, from now on, on the platforms that has hw_tracking let's
rely more on HW tracking.

This also is the case in used by other drivers and more validated
by SV teams. So I hope that this will lead us to less misterious
bugs.

v2: Only do this for platform that actually has hw tracking.

v3 from DK
Do this only for flips, small gradual changes are better.

Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Jim Bride <jim.bride@linux.intel.com>
Cc: Vathsala Nagaraju <vathsala.nagaraju@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Jose Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180307033420.3086-3-dhinakaran.pandiyan@intel.com

drm/i915/frontbuffer: HW tracking for cursor moves to fix PSR lags.

DRM_IOCTL_MODE_CURSOR results in frontbuffer flush before the cursor
plane MMIOs are written to. But this flush should not be necessary for
PSR as hardware tracking triggers PSR exit when MMIOs are written. As
for FBC, the spec says "Flips or changes to plane size and panning" cause
FBC to be nuked. Use origin == ORIGIN_FLIP so that features can ignore
cursor updates in their frontbuffer_flush implementations.

 /sys/kernel/debug/dri/0/i915_fbc_status shows
"Compressing: yes" when I move the cursor around.

v3: Use ORIGIN_FLIP now that pin_to_display does not flush frontbuffer.
v2: Update comment in i915_gem_object_pin_to_display_plane. (Chris)

Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180307033420.3086-2-dhinakaran.pandiyan@intel.com

drm/i915/frontbuffer: Pull frontbuffer_flush out of gem_obj_pin_to_display

i915_gem_obj_pin_to_display() calls frontbuffer_flush with origin set to
DIRTYFB. The callers however are at a vantage point to decide if hardware
frontbuffer tracking can do the flush for us. For example, legacy cursor
updates, like flips, write to MMIO registers, which then triggers PSR flush
by the hardware. Moving frontbuffer_flush out will enable us to skip a
software initiated flush by setting origin to FLIP. Thanks to Chris for the
idea.

v2:
Rebased due to Ville adding intel_plane_pin_fb().
Minor code reordering as fb_obj_flush doesn't need struct_mutex (Chris)

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180307033420.3086-1-dhinakaran.pandiyan@intel.com

drm/i915: Use sseu size for determining eu_regs[]

eu_regs[] is written 2*max_slices times (like s_reg[]) but oddly read
2*max_slices + max_subslices/2 times. Allocate the array large enough
for the writes to avoid overwriting our stack and worry about the logic
later.

Fixes: 7aa0b14ede64 ("drm/i915: Remove variable length arrays from sseu debugfs printers")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105479
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180313113149.1094-1-chris@chris-wilson.co.uk

drm/i915: Warn against variable length arrays

VLA are strongly discouraged in the kernel due to ambiguity they impose
on the limited stack space and security concerns over manipulating the
stack frame. Add -Wvla to our compiler flags so that CI rejects them.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180313004055.25411-2-chris@chris-wilson.co.uk

drm/i915: Remove variable length arrays from sseu debugfs printers

In order to enable -Wvla to prevent new variable length arrays being
used in i915.ko, we first must remove the existing VLA. Inside
i915_print_sseu_info(), VLA are used as the actual size of the sseu
depends on platform. Replace the VLA with the maximum required.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180313004055.25411-1-chris@chris-wilson.co.uk

drm/i915/uc: Sanitize uC together with GEM

Instead of dancing around uC on reset/suspend/resume scenarios,
explicitly sanitize uC when we sanitize GEM to force uC reload
and start from known beginning.

v2: don't forget about reset path (Daniele)
    sanitize uc before gem initiated full reset (Daniele)
v3: drop redundant disable_communication in init_hw (Daniele)

Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180312130308.22952-3-michal.wajdeczko@intel.com

drm/i915/uc: Sanitize uC options early

We are sanitizing uC related modparams together with other driver
modparams in intel_sanitize_options called from i915_driver_init_hw,
but this is too late for us as we will want to use USES_GUC/USES_HUC
macros at earlier stage. Since our sanitizing does not require any
MMIO access, we can do it in intel_uc_init_early right after we resolve
firmware names.

Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180312130308.22952-2-michal.wajdeczko@intel.com

drm/i915: Remove the impedance mismatch around intel_engine_enable_signaling

There is some redundancy between dma_fence->ops->enable_signaling (via
i915_fence_enable_signaling) and our backend,
intel_engine_enable_signaling() in that both levels recheck the fence
status multiple times. If we convert intel_engine_enable_signaling() to
return the information desired by dma_fence->ops->enable_signaling, we
can reduce i915_fence_enable_signaling to a simple stub and avoid
trying to reinterpret the same information.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Michal Winiarski <michal.winiarski@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180308140732.25090-1-chris@chris-wilson.co.uk

drm/i915/psr: Display WA 0884 applied broadly for more HW tracking.

WA 0884:bxt:all,cnl:*:A - "When FBC is enabled with eDP PSR,
the CPU host modify writes may not get updated on the Display
as expected.
WA: Write 0x00000000 to CUR_SURFLIVE_A with every CPU
host modify write to trigger PSR exit."

We can also find on spec other cases where they describe
bogus writes to cursor registers to force PSR exit with
HW tracking. And it was confirmed by HW engineers that
this Wa can be safely applied for any frontbuffer activity.

So let's use this more and more here instead of forcibly
disable and re-enable PSR everytime that we have a simple
reliable flush case.

Other commits improve the fbcon/fbdev use a lot, but this
approach is the only when where we can get a fully reliable
console with no slowness or missed frames and PSR still
enabled and active.

v2: - Rebase on drm-tip
    - (DK) Add a comment to explain that WA
    tells about writing 0 to CUR_SURFLIVE_A but we write to
    CUR_SURFLIVE(pipe).
v3: Wa doesn't work on PSR2.

Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180309005218.26772-1-rodrigo.vivi@intel.com

drm/i915: Move i915_gpu_error into its own header

Error state management code was moved into separate .c unit
but we didn't move related definitions into own header.

v2: move also intel_display_error_state forward decl
    fix ("Prefer 'unsigned int' to bare use of 'unsigned'")
    warnings detected by checkpatch in moved code (Michal)

Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180308095037.18264-5-michal.wajdeczko@intel.com

drm/i915: Make header i915_pmu.h more robust

Definitions in i915_pmu.h header depend on other types and
declarations that were not explicitly included. Fix that by
adding related headers and forward declarations.
While here, change license text to SPDX format.

v2: don't drop "intel_ringbuffer.h" (Tvrtko)

Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180308095037.18264-4-michal.wajdeczko@intel.com

drm/i915: Change parameters order in i915_gem_batch_pool_init

Function i915_gem_batch_pool_init() failed to follow obj-verb
naming schema. Fix that by swapping function parameters.
While here, change license text to SPDX format.

v2: use intel_engine_init_batch_pool (Chris) as proxy (Michal)

Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180308095037.18264-3-michal.wajdeczko@intel.com

drm/i915: Include i915_reg.h in intel_ringbuffer.h

Header intel_ringbuffer.h is using definitions from i915_reg.h
but forget to include it. Remove this hidden dependency by
explicitly include missing header.

v2: add reminder (Chris)

Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180308095037.18264-2-michal.wajdeczko@intel.com

drm/i915/guc: Move GuC notification handling to separate function

To allow future code reuse. While here, fix comment style.

v2: Notifications are a separate thing - rename the handler (Sagar)

Suggested-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Oscar Mateo <oscar.mateo@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Reviewed-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180308154707.21716-3-michal.winiarski@intel.com

drm/i915/guc: Create common entry points for log register/unregister

We have many functions responsible for allocating different parts of
GuC log runtime called from multiple places. Let's stick with keeping
everything in guc_log_register instead.

v2: Use more generic intel_uc_register name, keep using "misc" suffix (Michał)
    s/dev_priv/i915 (Sagar)
    Make guc_log_relay_* static (sparse)

Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Reviewed-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180308154707.21716-2-michal.winiarski@intel.com

drm/i915/guc: Tidy guc_log_control

We plan to decouple log runtime (mapping + relay) from verbosity control.
Let's tidy the code now to reduce the churn in the following patches.

v2: Tidy macros, keep debug messages, use helper var for enable,
    correct typo (Michał)
    Fix incorrect input validaction (Sagar)

Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Reviewed-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180308154707.21716-1-michal.winiarski@intel.com

drm/i915: Remove unused DP_LINK_CHECK_TIMEOUT

Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180308232421.14049-2-lyude@redhat.com

drm/i915: Only call tasklet_kill() on the first prepare_reset

tasklet_kill() will spin waiting for the current tasklet to be executed.
However, if tasklet_disable() has been called, then the tasklet is never
executed but permanently put back onto the runlist until
tasklet_enable() is called. Ergo, we cannot use tasklet_kill() inside a
disable/enable pair. This is the case when we call set-wedge from inside
i915_reset(), and another request was submitted to us concurrent to the
reset.

Fixes: 963ddd63c314 ("drm/i915: Suspend submission tasklets around wedging")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180307134226.25492-6-chris@chris-wilson.co.uk

drm/i915: Wrap engine->schedule in RCU locks for set-wedge protection

Similar to the staging around handling of engine->submit_request, we
need to stop adding to the execlists->queue prior to calling
engine->cancel_requests. cancel_requests will move requests from the
queue onto the timeline, so if we add a request onto the queue after that
point, it will be lost.

Fixes: af7a8ffad9c5 ("drm/i915: Use rcu instead of stop_machine in set_wedged")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180307134226.25492-5-chris@chris-wilson.co.uk

drm/i915: Include ring->emit in debugging

Include ring->emit and ring->space alongside ring->(head,tail) when
printing debug information.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180307134226.25492-4-chris@chris-wilson.co.uk

drm/i915: Update ring position from request on retiring

When wedged, we do not update the ring->tail as we submit the requests
causing us to leak the ring->space upon cleaning up the wedged driver.
We can just use the value stored in rq->tail, and keep the submission
backend details away from set-wedge.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180307134226.25492-3-chris@chris-wilson.co.uk

drm/i915: Finish the wait-for-wedge by retiring all the inflight requests

Before we reset the GPU after marking the device as wedged, we wait for
all the remaining requests to be completed (and marked as EIO).
Afterwards, we should flush the request lists so the next batch start
with the driver in an idle state.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180307134226.25492-1-chris@chris-wilson.co.uk