Mathew McBride [Tue, 22 Aug 2023 04:49:32 +0000 (04:49 +0000)]
x86: remove built-in vhost-net driver
This is now available as a kmod package (kmod-vhost-net).
Signed-off-by: Mathew McBride <matt@traverse.com.au>
(cherry picked from commit
8b1cc1582ad9c9b12d52870e0c7f9cb828aa0fbf)
Mathew McBride [Mon, 21 Aug 2023 06:10:35 +0000 (06:10 +0000)]
kernel: add vhost-net module
vhost-net is used to accelerate traffic to virtualisation
guests that use the virtio-net network card in QEMU.
Generally it is invoked by specifying "vhost=on" to a
QEMU -netdev device:
qemu-system-aarch64 -nographic -M virt -cpu host \
--enable-kvm -bios u-boot.bin -smp 1 -m 2048 \
-drive file=openwrt-armsr-armv8.img,format=raw,index=0,media=disk \
-device "virtio-net,netdev=landev,disable-legacy=off,disable-modern=off" \
-netdev "tap,id=landev,helper=/usr/lib/qemu-bridge-helper --br=br-lan,vhost=on"
Signed-off-by: Mathew McBride <matt@traverse.com.au>
(cherry picked from commit
d188db8aed74547f98b905254d4f57baf225f1d6)
INAGAKI Hiroshi [Sat, 2 Sep 2023 14:06:20 +0000 (23:06 +0900)]
mvebu: add reset delays of PHYs for Fortinet FortiGate 50E
Add reset-(de)assert-us to ethernet PHYs on Fortinet FortiGate 50E to
solve instability after HW resetting of PHYs. (ex.: restarting "network"
service, etc...)
Fixes: #13391
Fixes: 102dc5a62506 ("mvebu: add support for Fortinet FortiGate 50E")
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
(cherry picked from commit
5c65224d8f5787f6bdfaec9547637f1f2f46354f)
Brian Norris [Sun, 10 Sep 2023 21:10:50 +0000 (14:10 -0700)]
ipq806x: Correct OnHub sysupgrade config logic
There's a typo in here: board_name is a function, not a variable. This
issue was pointed out on the OpenWrt forum.
Closes: #13409
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
(cherry picked from commit
7b78a19e6a16f5c05bfc6d7925b9981048c508d7)
Jonas Gorski [Sat, 9 Sep 2023 10:44:42 +0000 (12:44 +0200)]
x86: geode: fix hwrng register accesses
When the membase and pci_dev pointer were moved to a new struct in priv,
the actual membase users were left untouched, and they started reading
out arbitrary memory behind the struct instead of registers. This
unfortunately turned the RNG into a constant number generator, depending
on the content of what was at that offset.
To fix this, update geode_rng_data_{read,present}() to also get the
membase via amd_geode_priv, and properly read from the right addresses
again.
Closes #13417.
Reported-by: Timur I. Davletshin <timur.davletshin@gmail.com>
Tested-by: Timur I. Davletshin <timur.davletshin@gmail.com>
Suggested-by: Jo-Philipp Wich <jo@mein.io>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
(cherry picked from commit
09d13cd8d87cc50fde67bbe81c6cca4b799b2724)
Hannu Nyman [Fri, 8 Sep 2023 16:47:01 +0000 (19:47 +0300)]
base-files: sysupgrade: Add 2 sec sleep into process KILL loop
Add 2 seconds sleep after each forcibly killed/tried-to-kill process
in the final process termination loop in sysupgrade stage2.
This is needed especially for qualcommax/ipq807x, where ath11k
wireless driver may have a long 10-20 seconds delay after termination
before actually getting killed. This often breaks sysupgrade.
The current KILL loop in kill_remaining does all 10 kill attempts
consecutively without any delay, as evidenced here in a failing sysupgrade.
It does not allow any time for the process to finalize its internal
termination.
Sat Sep 2 19:05:56 EEST 2023 upgrade: Sending TERM to remaining processes ...
Sat Sep 2 19:05:56 EEST 2023 upgrade: Sending signal TERM to hostapd (2122)
Sat Sep 2 19:05:56 EEST 2023 upgrade: Sending signal TERM to hostapd (2138)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending KILL to remaining processes ...
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending signal KILL to hostapd (2122)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending signal KILL to hostapd (2138)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending signal KILL to hostapd (2138)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending signal KILL to hostapd (2138)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending signal KILL to hostapd (2138)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending signal KILL to hostapd (2138)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending signal KILL to hostapd (2138)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending signal KILL to hostapd (2138)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending signal KILL to hostapd (2138)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending signal KILL to hostapd (2138)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending signal KILL to hostapd (2138)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Failed to kill all processes.
sysupgrade aborted with return code: 256
The change in this commit adds a 2 seconds delay after each kill attempt
in order to allow some processes to more gracefully handle their
internal termination.
The result is like this:
Sun Sep 3 11:15:10 EEST 2023 upgrade: Sending TERM to remaining processes ...
Sun Sep 3 11:15:10 EEST 2023 upgrade: Sending signal TERM to hostapd (2309)
Sun Sep 3 11:15:10 EEST 2023 upgrade: Sending signal TERM to hostapd (2324)
Sun Sep 3 11:15:14 EEST 2023 upgrade: Sending KILL to remaining processes ...
Sun Sep 3 11:15:14 EEST 2023 upgrade: Sending signal KILL to hostapd (2309)
[ 699.827521] br-lan: port 7(hn5wpa2r) entered disabled state
[ 699.908673] device hn5wpa2r left promiscuous mode
[ 699.908721] br-lan: port 7(hn5wpa2r) entered disabled state
[ 701.038029] br-lan: port 6(hn5wpa3) entered disabled state
Sun Sep 3 11:15:16 EEST 2023 upgrade: Sending signal KILL to hostapd (2324)
[ 702.058256] br-lan: port 5(hn2wlan) entered disabled state
[ 709.250063] stage2 (8237): drop_caches: 3
Sun Sep 3 11:15:25 EEST 2023 upgrade: Switching to ramdisk...
The delay introduced here only kicks in if there is some process that
does not get terminated by the first TERM call. Then there is at least
one 2 sec wait after the first KILL loop round.
This commit is related to discussion in PRs #12235 and #12632
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Reviewed-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit
47d56ae5463f1965750d3f75390c96d69f969145)
Piotr Dymacz [Fri, 28 Jul 2023 10:21:49 +0000 (12:21 +0200)]
uboot-envtools: ramips: add support for ALFA Network AX1800RM
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
(backported from commit
69f12c2f23c6d32a5fdda2385b4156c9b8bfae22)
Piotr Dymacz [Fri, 28 Jul 2023 09:41:14 +0000 (11:41 +0200)]
ramips: add support for ALFA Network AX1800RM
ALFA Network AX1800RM (FCC ID:
2AB877621) is a dual-band Wi-Fi 6
(AX1800) router, based on MediaTek MT7621A + MT79x5D platform.
Specifications:
- SOC: MT7621A (880 MHz)
- DRAM: DDR3 256 MiB (Nanya NT5CC128M16JR-EK)
- Flash: 16 MiB SPI NOR (EN25QH128A-104HIP)
- Ethernet: 4x 10/100/1000 Mbps (SOC's built-in switch)
- Wi-Fi: 2x2:2 2.4/5 GHz (MT7905DAN + MT7975DN)
(MT7905DAN doesn't support background DFS scan/BT)
- LED: 6x green, 1x green/red
- Buttons: 2x (reset, WPS)
- Antenna: 4x external, non-detachable omnidirectional
- UART: 1x 4-pin (2.54 mm pitch, J4, not populated)
- Power: 12 V DC/1 A (DC jack)
MAC addresses:
LAN: 00:c0:ca:xx:xx:4e (factory 0x4, +2)
WAN: 00:c0:ca:xx:xx:4f (factory 0x4, +3)
2.4 GHz: 00:c0:ca:xx:xx:4c (factory 0x4, device's label)
5 GHz: 00:c0:ca:xx:xx:4c (factory 0xa)
Flash instructions for web-based U-Boot recovery:
1. Power the device with WPS button pressed and wait around 10 seconds.
2. Setup static IP 192.168.1.2/24 on your PC.
3. Go to 192.168.1.1 in browser and upload 'recovery' image.
The device runs LEDE 17.01 (kernel 4.4.x) based firmware with 'failsafe'
mode available which allows alternative upgrade method:
1. Run device in 'failsafe' mode and change password for default user.
2. SSH to the device, transfer 'sysupgrade' image and perform upgrade
in forced mode, without preserving settings: 'sysupgrade -n -F ...'.
Other notes:
If you own early version of this device, the vendor firmware might
refuse OpenWrt image because of missing custom header. In that case,
ask vendor's customer support for stock firmware without custom header
support/requirement.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
(backported from commit
f1aaa267f0ea18ffe5840f3ce46a48be123d2f62)
Daniel Golle [Sun, 10 Sep 2023 22:39:33 +0000 (23:39 +0100)]
arm-trusted-firmware-mediatek: fix hang on reboot on MT7622
With recent updates of TF-A the previously already fixed bug slipped
back into the source tree. Again, reorder bl2 init for MT7622 and
initialize WDT only after DRAM init has completed to avoid the
notorious hang.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit
948ad2ec7a21645bac4d523c8f31d1cc3e2eac71)
Daniel Golle [Fri, 1 Sep 2023 23:54:40 +0000 (00:54 +0100)]
uboot-mediatek: sync mtk-snand driver with SDK
Sync SPI-NAND/ECC controller driver for MT7622, MT7981, MT7986 and MT7988:
* Platform data for MT7981 was actually missing and is now added.
* Add support for Winbond W25N01KV 1Gbit chip.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit
9725524235b30b436f6430d70cd809abf1b48a91)
Shiji Yang [Tue, 22 Aug 2023 18:16:22 +0000 (19:16 +0100)]
mac80211: fix MT7620 Wi-Fi channel scanning function
During the channel scanning process, the driver will continuously
switch channels. It seems that the full RF calibration step in
rt2800_config_channel() caused the channel scanning function to
timeout. To fix it, move the RF calibration to rt2800_enable_radio()
so that it is only executed once. This commit also includes some
coding format adjustments to follow the Linux recommended style.
Fixes: 2824fa6963cf ("mac80211: rework MT7620 PA/LNA RF calibration")
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
(cherry picked from commit
ce6ad123e76311d2a882054b4ea532d1bfb643c8)
Shiji Yang [Sat, 29 Jul 2023 13:24:10 +0000 (21:24 +0800)]
ramips: pinctrl: support requesting different functions for same group
MT7620 wireless radio needs change the pin group function between
"gpio" and "pa" during the calibration process. However, ralink
pinctrl driver doesn't support requesting different functions for
the same group. This patch enables pinctrl consumers to perform
such operations.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
(cherry picked from commit
b4ea49ad442d2884d0b86009f404f125635c4153)
Shiji Yang [Sat, 29 Jul 2023 13:24:09 +0000 (21:24 +0800)]
mac80211: rework MT7620 PA/LNA RF calibration
This patch makes some improvements to the MT7620 RF calibration.
1. Move MT7620 PA/LNA calibration code to dedicated functions.
2. Restore RF and BBP registers before R-Calibration.
3. Do Rx DCOC calibration again before RXIQ calibration.
4. Use SoC specific AGC initial LNA value.
5. Correct MAC_RX_EN mask in rt2800_r_calibration()[1].
[1] This change may fix the "BBP/RF register access failed" error:
ieee80211 phy0: rt2800_wait_bbp_rf_ready: Error - BBP/RF register access failed, aborting
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
(cherry picked from commit
2824fa6963cf245b7e0b04aa96bcbe5013524b85)
Daniel Golle [Thu, 31 Aug 2023 18:20:49 +0000 (19:20 +0100)]
mediatek: mt7622: set DEVICE_DTC_ADDR for BPi-R64
Relocating the device tree is required for being apply to apply
device tree overylay at boot.
Fixes: 34bb33094a ("mediatek: use updated device tree overlay mechanism for BPi-R64")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit
a8cbee8e2d11dd139c1dea1f7289bdf28b1e2b52)
Daniel Golle [Mon, 28 Aug 2023 22:44:52 +0000 (23:44 +0100)]
arm-trusted-firmware-mediatek: enable built-in 2.5G PHY on MT7988
Always enable built-in 2.5G PHY on MT7988 for now, so that it can be
used. In future it would be nice to be able to switch power and MDIO
access via address 0 at run-time in Linux, both, to be able to use
external PHYs at address 0 and to reduce power consumption on systems
not using the built-in 2.5G PHY.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit
33046d2a471ed687404a617c356b9cdf5652c2d6)
Daniel Golle [Mon, 28 Aug 2023 22:41:43 +0000 (23:41 +0100)]
uboot-mediatek: fix dependency on TF-A for MT7988 RFB (sdmmc)
The U-Boot build for the MT7988 reference board booting from SD card
wrongly depended on the 'ddr4' variant of the ARM TrustedFirmware-A build
even though the 'comb' variant is used. Fix that dependency.
Fixes: 572ea68070 ("uboot-mediatek: add patches for MT7988 and builds for RFB")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit
78e3adcaf993cd1a58821a69efccfca8d380f754)
Daniel Golle [Mon, 28 Aug 2023 20:54:02 +0000 (21:54 +0100)]
mediatek: filogic: remove stray quote
When adapting the network configuration for MT7988 RFB a stray quote
was left in a script. Remove it to fix generating the default network
configuration.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit
8f5986355cdc5df921ef8232f559ca7bfb18f1ed)
Daniel Golle [Sat, 26 Aug 2023 01:19:18 +0000 (02:19 +0100)]
generic: sync MediaTek Ethernet driver with upstream
Import commits from upstream Linux replacing some downstream patches.
Move accepted patches from pending-{5.15,6.1} to backport-{5.15,6.1}.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit
f631c7bbb16f1d39d59c4cdf3f7189abab4fd9c6)
Daniel Golle [Sun, 27 Aug 2023 23:14:10 +0000 (00:14 +0100)]
mediatek: add support for Ubiquiti UniFi 6 LR v3
Some recent models of the Ubiquiti Networks UniFi 6 LR access point
come with a RealTek RTL8211FS 1000M/100M/10M PHY instead of the
Aquantia AQR112 2500M/1000M/100M/10M PHY used in both v1 and v2. Add
build for this variant so we can support Ethernet with the PHY.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit
a0f4eadf6a25fb54c189bde91425673e11125d35)
Daniel Golle [Sun, 27 Aug 2023 23:13:05 +0000 (00:13 +0100)]
uboot-mediatek: add builds for UniFi 6 LR v2 and v3
While the v2 is nearly identical to v1, v3 uses a different PHY and
needs a different build for Ethernet to work in U-Boot.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit
fff4441135ed9290eb2f947f931b826a60d6c167)
Daniel Golle [Fri, 25 Aug 2023 03:09:28 +0000 (04:09 +0100)]
mediatek: generate bootloader artifacts for mt7988_rfb
Switch to OpenWrt uImage.FIT bootmethod and include various bootloader
artifacts with the generated binaries.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit
035a88ae5564ac680c64ed7219b8b66733ac84c6)
Daniel Golle [Fri, 25 Aug 2023 02:58:33 +0000 (03:58 +0100)]
uboot-mediatek: build fully-featured U-Boot for MT7988 RFB
Select many potentially useful options for the MT7988 RFB U-Boot builds.
The resulting loader is intended as a development tool and intends to be
generic. It does *not* have a default bootcmd set, but allows to boot
pretty much everything, including EFI executables.
To install this U-Boot build to the eMMC:
opkg install mmc-utils partx-utils
mmc bootpart enable 1 1 /dev/mmcblk0
echo 0 > /sys/block/mmcblk0boot0/force_ro
dd if=*mediatek_mt7988a-rfb-nand-emmc-preloader.bin of=/dev/mmcblk0boot0
dd if=*mediatek_mt7988a-rfb-nand-emmc-gpt.bin of=/dev/mmcblk0
partx -a /dev/mmcblk0
dd if=*mediatek_mt7988a-rfb-nand-emmc-bl31-uboot.fip of=/dev/mmcblk0p3
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit
1d5778e18d9a6bef26aff3a8594306fc45e9be76)
Daniel Golle [Sun, 27 Aug 2023 14:57:00 +0000 (15:57 +0100)]
mediatek: improve mt7981.dtsi
* re-factor WED components to boot fine also on limited loaders
* add LEDs of integrated GE PHY
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit
3ef8760e876e09fa91b54a09b2a5003c175829d3)
Daniel Golle [Sat, 26 Aug 2023 23:38:38 +0000 (00:38 +0100)]
mediatek: filogic: improve pinctrl drivers
Set correct pull-type data and add additional uart groups for MT7981.
Assign functions to configure pin bias for MT7986.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit
9f8fde216d994ce47b1eca15de190aa9b8f67b9a)
Daniel Golle [Sat, 26 Aug 2023 21:26:37 +0000 (22:26 +0100)]
mediatek: i2c: mt65xx: allow optional pmic clock
Using the I2C host controller on the MT7981 SoC requires 4 clocks to
be enabled. One of them, the pmic clk, is only enabled in case
'mediatek,have-pmic' is also set which has other consequences which
are not desired in this case.
Allow defining a pmic clk even in case the 'mediatek,have-pmic' propterty
is not present and the bus is not used to connect to a pmic, but may
still require to enable the pmic clock.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit
2544dc34f2a6e5721096ee62efa66d36d45b2dd1)
Daniel Golle [Fri, 25 Aug 2023 13:00:09 +0000 (14:00 +0100)]
mediatek: re-add dropped properties on BPi-R3
Unfortunately some device tree properties have slipped under the table
when switching from our downstream device tree.
Bring back 3W power for SFP cages and restore thermal trip points to
make sense again.
Fixes: 7a0ec001ff ("mediatek: sync MT7986 device trees with upstream")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit
06a150aed795066ce79a623011884cc0abf290f1)
Christian Marangi [Sun, 4 Jun 2023 02:26:59 +0000 (04:26 +0200)]
generic: backport initial LEDs hw control support
Backport initial LEDs hw control support. Currently this is limited to
only rx/tx and link events for the netdev trigger but the API got
accepted and the additional modes are working on and will be backported
later.
Refresh every patch and add the additional config flag for QCA8K new
LEDs support.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit
0a4b309f41062ef40706162ae53b6428982a0685)
John Audia [Sat, 2 Sep 2023 12:42:48 +0000 (08:42 -0400)]
kernel: bump 5.15 to 5.15.130
Changelog: https://cdn.kernel.org/pub/linux/kernel/v5.x/ChangeLog-5.15.130
No patches needed a rebased. Update to checksum only.
Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3
Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit
e793b4bde535b86aab35512c8791c805444e5aff)
John Audia [Wed, 30 Aug 2023 18:44:05 +0000 (14:44 -0400)]
kernel: bump 5.15 to 5.15.129
Changelog: https://cdn.kernel.org/pub/linux/kernel/v5.x/ChangeLog-5.15.129
All patches automatically rebased.
Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3
Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit
1db566b6928447ff4c4f86ad1be7e0a6d5a58d16)
[Refresh on top of OpenWrt 23.05]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
John Audia [Sat, 26 Aug 2023 16:56:53 +0000 (12:56 -0400)]
kernel: bump 5.15 to 5.15.128
Changelog: https://cdn.kernel.org/pub/linux/kernel/v5.x/ChangeLog-5.15.128
All patches automatically rebased.
Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3
Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit
e80a3875172178cdcc02d13826717413cc1534a8)
[Refresh on OpenWrt 23.05]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Felix Fietkau [Fri, 1 Sep 2023 10:43:09 +0000 (12:43 +0200)]
kernel: allow adding devices without hw offload to a hw flowtable
This allows supporting a mix of devices with or without hw offloading support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit
c5b7be83168644f3cfadc7b0fbe471e1664b1069)
Rafał Miłecki [Tue, 25 Jul 2023 07:51:35 +0000 (09:51 +0200)]
urngd: update to the latest master
7aefb47 jitterentropy-rngd: update to the v1.2.0
What's interesting about jitterentropy-rngd v1.2.0 release is that it
bumps its copy of jitterentropy-library from v2.2.0 to the v3.0.0. That
bump includes a relevant commit
3130cd9 ("replace LSFR with SHA-3 256").
When initializing entropy jent calculates time delta. Time values are
obtained using clock_gettime() + CLOCK_REALTIME. There is no guarantee
from CLOCK_REALTIME of unique values and slow devices often return
duplicated ones.
A switch from jent_lfsr_time() to jent_hash_time() resulted in many less
cases of zero delta and avoids ECOARSETIME.
Long story short: on some system this fixes:
[ 6.722725] urngd: jent-rng init failed, err: 2
This is important change for BCM53573 which doesn't include hwrng and
seems to have arch_timer running at 36,8 Hz.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit
c74b5e09e692839b39c8325b5f8dc5f2a3b3896c)
Nick Hainke [Wed, 19 Jul 2023 06:33:32 +0000 (08:33 +0200)]
nettle: update to 3.9.1
Announcement:
https://lists.gnu.org/archive/html/info-gnu/2023-06/msg00000.html
Signed-off-by: Nick Hainke <vincent@systemli.org>
(cherry picked from commit
fabd8915698d9fb21aa80100a51e097505b61225)
Robert Marko [Sun, 27 Aug 2023 10:18:45 +0000 (12:18 +0200)]
Revert "ath11k-firmware: update to stable WLAN.HK.2.9.0.1-01837"
This reverts commit
23953cfa5afa2e8cd9e1c1475d065cb954d8ceb6.
01837 seems to be having multiple issues, one being broken multicast so
lets revert to the last version that was better for the stable branch.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Felix Fietkau [Wed, 26 Jul 2023 11:20:43 +0000 (13:20 +0200)]
mt76: update to the latest version
bdf7ca5db707 wifi: mt76: mt7921: move common register definition in mt792x_regs.h
ae15d5c6b567 wifi: mt76: mt7921: convert acpisar and clc pointers to void
02515b6b90f0 wifi: mt76: mt7921: rename mt7921_vif in mt792x_vif
6ed8a8bdc7b6 wifi: mt76: mt7921: rename mt7921_sta in mt792x_sta
80234e64e7c5 wifi: mt76: mt7921: rename mt7921_phy in mt792x_phy
2485b4222d3d wifi: mt76: mt7921: rename mt7921_dev in mt792x_dev
c6fd7cde77e0 wifi: mt76: mt7921: rename mt7921_hif_ops in mt792x_hif_ops
1a1a57b5f8c4 wifi: mt76: mt792x: move shared structure definition in mt792x.h
68508aab4241 wifi: mt76: mt7921: move mt792x_mutex_{acquire/release} in mt792x.h
ff306af07e65 wifi: mt76: mt7921: move mt792x_hw_dev in mt792x.h
4b49d659acab wifi: mt76: mt7921: Replace fake flex-arrays with flexible-array members
93f821cce8f5 wifi: mt76: mt792x: introduce mt792x-lib module
de7b90721280 wifi: mt76: mt7921: move mac shared code in mt792x-lib module
c68ee8a64bef wifi: mt76: mt7921: move dma shared code in mt792x-lib module
8d561811f271 wifi: mt76: mt7921: move debugfs shared code in mt792x-lib module
0034ae289046 wifi: mt76: mt7921: move init shared code in mt792x-lib module
8419c4e793a7 wifi: mt76: mt792x: introduce mt792x_irq_map
b7c7fadf228c wifi: mt76: mt792x: move more dma shared code in mt792x_dma
0b1603ce707c wifi: mt76: mt7921: move hif_ops macro in mt792x.h
e07540abe87a wifi: mt76: mt7921: move shared runtime-pm code on mt792x-lib
3d65cd7a8dad wifi: mt76: mt7921: move runtime-pm pci code in mt792x-lib
4551f8c838e6 wifi: mt76: mt7921: move acpi_sar code in mt792x-lib module
bd84b8ebaff8 wifi: mt76: mt792x: introduce mt792x-usb module
7067ea0f1bab wifi: mt76: mt792x: move mt7921_load_firmware in mt792x-lib module
cf752af84c35 wifi: mt76: mt76_connac3: move lmac queue enumeration in mt76_connac3_mac.h
700041dcf773 wifi: mt76: mt792x: move MT7921_PM_TIMEOUT and MT7921_HW_SCAN_TIMEOUT in common code
58b2b90ad89b wifi: mt76: mt7921: move mt7921_dma_init in pci.c
9e4cb87a04cf wifi: mt76: mt7921: move mt7921u_disconnect mt792x-lib
c19b62fe6b68 wifi: mt76: testmode: add nla_policy for MT76_TM_ATTR_TX_LENGTH
4904ab2f87cd wifi: mt76: fix return value check in mt76x02_mac_process_rx
1f0fbbee359c wifi: mt76: mt7915: fix tlv length of mt7915_mcu_get_chan_mib_info
24a54ee3a5ec wifi: mt76: mt7915: fix power-limits while chan_switch
80b8bcf0e3ea wifi: mt76: mt7603: rework/fix rx pse hang check
a8d9553d8fc4 wifi: mt76: mt7603: improve watchdog reset reliablity
c03d84c0d018 wifi: mt76: mt7603: improve stuck beacon handling
85cc58378d25 wifi: mt76: mt7603: add missing register initialization for MT7628
b14c2351ddb8 wifi: mt76: mt7603: disable A-MSDU tx support on MT7628
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit
6b3737be323f702d5c1c5533db7d7351603dad0f)
David Bauer [Fri, 25 Aug 2023 19:38:13 +0000 (21:38 +0200)]
mediatek: enable NMBM remapping for NWA50AX Pro UBI
Don't skip remapping of the UBI area for the ZyXEL NWA50AX Pro. This is
due to the kernel being loaded from the UBI partition by U-Boot.
Link: https://github.com/openwrt/openwrt/pull/13335
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit
6dc0675e5b9d59a882972b8d478ee9fa8496ae51)
Shiji Yang [Sun, 9 Jul 2023 14:10:54 +0000 (22:10 +0800)]
ath79: fix first reboot issue on Netgear WNDR4300 v2 and WNDR4500 v3
From the Netgear u-boot GPL code[1]. Bootloader always unconditionally
marks block 768, 1020 - 1023 as bad blocks on each boot. This may lead
to conflicts with the OpenWrt nand driver since these blocks may be good
blocks. In this case, U-boot will override the oob of these blocks so
that break the ubi volume. The system will be damaged after first reboot.
To avoid this issue, manually skip these blocks by using "mtd-concat".
[1] https://www.downloads.netgear.com/files/GPL/EX7300v2series-V1.0.0.146_gpl_src.tar.bz2.zip
Fixes: https://github.com/openwrt/openwrt/issues/8878
Tested-by: Yousaf <yousaf465@gmail.com>
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
(cherry picked from commit
12f53724c6575245cf8b2f0dc75d1b9b2e4fe488)
Shiji Yang [Sun, 9 Jul 2023 14:10:53 +0000 (22:10 +0800)]
ath79: rework Netgear nand devices image recipe
In Netgear u-boot GPL code, nand devices uses this formula to locate the
rootfs offset.
offset = (((128 + KERNEL_SIZE) / BLOCK_SIZE) + 1) * BLOCK_SIZE;
Howerver, WNDR4500 source code incorrectly define the nand block size to
64k. In some cases, it causes u-boot can't get the correct rootfs offset,
which result in boot failure. This patch workaround it by padding kernel
size to (128k * n - 128 - 1). The additional char '\0' is used to ensure
the (128 + KERNEL_SIZE) can't be divided by the BLOCK_SIZE.
Fixes: https://github.com/openwrt/openwrt/issues/13050
Fixes: 3c1512a25d92 ("ath79: optimize the firmware recipe for Netgear NAND devices")
Tested-by: Yousaf <yousaf465@gmail.com>
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
(cherry picked from commit
0f9b8aa3f592b22e3f1d5f7d049e92653ba0f884)
Stefan Agner [Fri, 30 Jun 2023 10:34:38 +0000 (12:34 +0200)]
mediatek: filogic: wax220: cleanup device tree
Fix compatible string to match what is supported upstream, fix alignment
and order MTD partitions according to offset.
Signed-off-by: Stefan Agner <stefan@agner.ch>
(cherry picked from commit
4af06aaf33c9256a5d3e960fa5f6bddab2674c5a)
Stefan Agner [Fri, 30 Jun 2023 09:52:37 +0000 (11:52 +0200)]
mediatek: filogic: wax220: support factory image
Enable building a factory image which can be flashed through the OEM
firmware's web interface. It seems that the web interface requires a
minimum file size of 10MiB, otherwise it will not accept the image.
The update image is a regular sysupgrade tarball packed in a Netgear
encrypted image. The Netgear encrypted image is the same as used in
WAX202 or WAX206, including the encryption keys and IV.
This adds a script which creates the rootfs_data volume on first
startup. This is required since the OEM firmware's sysupgrade scripts
do not create such a paritition. Note that any script ordered after
70_initramfs_test will not get executed on initramfs. Hence this new
script 75_rootfs_prepare won't create the rootfs_data volume when
using the recovery initramfs.
Also, this deletes the kernel_backup and rootfs_backup volumes in case
we have to create the rootfs_data volumes. This makes sure that
OpenWrt is the actual backup firmware instead of the stock firmware.
References in WAX220 GPL source:
https://www.downloads.netgear.com/files/GPL/WAX220-V1.0.2.8-gpl-src.tar.gz
* package/base-files/files/lib/upgrade/nand.sh:186
Creation of rootfs_data is disabled
* Uboot-upstream/board/mediatek/common/ubi_helper.c
Automatic creation of UBI backup volumes
Signed-off-by: Stefan Agner <stefan@agner.ch>
(cherry picked from commit
fa9d977f979461628161085dcd0e9dd8b9e2c66b)
David Bauer [Mon, 7 Aug 2023 23:04:16 +0000 (01:04 +0200)]
mediatek: enable NWA50AX Pro eth LEDs
Enable the ethernet LED's on the ZyXEL NWA50AX Pro to show link-state as
well as activity.
Both LED's are configured pulsing.
AMBER | 10/100
GREEN | 1000
A+G | 2500
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit
4c0fdad7eabe7a5b81a7a1bd7f38dcadbe4f471a)
David Bauer [Thu, 17 Aug 2023 15:55:26 +0000 (17:55 +0200)]
mediatek: add missing packages for Acer Predator W6
Add missing packages for creating the overlay filesystem.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit
c35ff41ccc31f2ecaea7406830de04bd77940d48)
Andreas Böhler [Mon, 10 Jul 2023 09:55:30 +0000 (11:55 +0200)]
ipq4019: add support for ZTE MF287 Pro aka DreiNeo Pro
The ZTE MF287 Pro is a LTE router used (exclusively?) by the network
operator "3". It is very similar to the MF287+, but the hardware layout
and partition layout have changed quite a bit.
Specifications
==============
SoC: IPQ4018
RAM: 256MiB
Flash: 8MiB SPI-NOR + 128MiB SPI-NAND
LAN: 4x GBit LAN
LTE: ZTE Cat12
WiFi: 802.11a/b/g/n/ac SoC-integrated
USB: 1x 2.0
MAC addresses
=============
LAN: from config + 2
WiFi 1: from config
WiFi 2: from config + 1
Installation
============
Option 1 - TFTP
---------------
TFTP installation using UART is preferred. Disassemble the device and
connect serial. Put the initramfs image as openwrt.bin to your TFTP server
and configure a static IP of 192.168.1.100. Load the initramfs image by
typing:
setenv serverip 192.168.1.100
setenv ipaddr 192.168.1.1
tftpboot 0x82000000 openwrt.bin
bootm 0x82000000
From this intiramfs boot you can take a backup of the currently installed
partitions as no vendor firmware is available for download:
ubiattach -m17
cat /dev/ubi0_0 > /tmp/ubi0_0
cat /dev/ubi0_1 > /tmp/ubi0_1
Copy the files /tmp/ubi0_0 and /tmp/ubi0_1 somewhere save.
Once booted, transfer the sysupgrade image and run sysupgrade. You might
have to delete the stock volumes first:
ubirmvol /dev/ubi0 -N ubi_rootfs
ubirmvol /dev/ubi0 -N kernel
Option 2 - From stock firmware
------------------------------
The installation from stock requires an exploit first. The exploit consists
of a backup file that forces the firmware to download telnetd via TFTP from
192.168.0.22 and run it. Once exploited, you can connect via telnet and
login as admin:admin.
The exploit will be available at the device wiki page.
Once inside the stock firmware, you can transfer the -factory.bin file to
/tmp by using "scp" from the stock frmware or "tftp".
ZTE has blocked writing to the NAND. Fortunately, it's easy to allow write
access - you need to read from one file in /proc. Once done, you need to
erase the UBI partition and flash OpenWrt. Before performing the operation,
make sure that mtd13 is the partition labelled "rootfs" by calling
"cat /proc/mtd".
Complete commands:
cd /tmp
tftp -g -r factory.bin 192.168.0.22
cat /proc/driver/sensor_id
flash_erase /dev/mtd17 0 0
dd if=/tmp/factory.bin of=/dev/mtdblock17 bs=131072
Afterwards, reboot your device and you should have a working OpenWrt
installation.
Restore Stock
=============
Option 1 - via UART
-------------------
Boot an OpenWrt initramfs image via TFTP as for the initial installation.
Transfer the two backed-up files to your box to /tmp.
Then, run the following commands - replace $kernel_length and $rootfs_size
by the size of ubi0_0 and ubi0_1 in bytes.
ubiattach -m 17
ubirmvol /dev/ubi0 -N kernel
ubirmvol /dev/ubi0 -N rootfs
ubirmvol /dev/ubi0 -N rootfs_data
ubimkvol /dev/ubi0 -N kernel -s $kernel_length
ubimkvol /dev/ubi0 -N ubi_rootfs -s $rootfs_size
ubiupdatevol /dev/ubi0_0 /tmp/ubi0_0
ubiupdatevol /dev/ubi0_1 /tmp/ubi0_1
Option 2 - from within OpenWrt
------------------------------
This option requires to flash an initramfs version first so that access
to the flash is possible. This can be achieved by sysupgrading to the
recovery.bin version and rebooting. Once rebooted, you are again in a
default OpenWrt installation, but no partition is mounted.
Follow the commands from Option 1 to flash back to stock.
LTE Modem
=========
The LTE modem is similar to other ZTE devices and controls some more LEDs
and battery management.
Configuring the connection using uqmi works properly, the modem
provides three serial ports and a QMI CDC ethernet interface.
Other Notes
===========
Contrary to the stock firmware, the USB port on the back can be used.
There is one GPIO Switch "Power button blocker" which, if enabled, does not
trigger a reset of the SoC if the modem reboots. If disabled, the SoC is
rebooted along with the modem. The modem can be rebooted via the exported
GPIO "modem-reset" in /sys/class/gpio.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
(cherry picked from commit
edfe91372adfdaf5ee4e294fb0f5860a16adc551)
Hauke Mehrtens [Sun, 20 Aug 2023 19:50:26 +0000 (21:50 +0200)]
OpenWrt v23.05.0-rc3: revert to branch defaults
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sun, 20 Aug 2023 19:50:15 +0000 (21:50 +0200)]
OpenWrt v23.05.0-rc3: adjust config defaults
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Stijn Tintel [Fri, 4 Aug 2023 07:03:10 +0000 (10:03 +0300)]
hostapd: revert upstream commit to fix #13156
Commit
e978072baaca ("Do prune_association only after the STA is
authorized") causes issues when an STA roams from one interface to
another interface on the same PHY. The mt7915 driver is not able to
handle this properly. While the commits fixes a DoS, there are other
devices and drivers with the same limitation, so revert to the orginal
behavior for now, until we have a better solution in place.
Fixes: #13156
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
(cherry picked from commit
324673914d42f5fb9b70cc73e955117828b99f3b)
Mathew McBride [Wed, 16 Aug 2023 06:43:18 +0000 (06:43 +0000)]
armsr: add kmod-sfp to default device profile
This brings the 23.05 branch into parity with the main.
kmod-sfp was in the main branch profile but not the 23.05 version.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Mathew McBride [Mon, 14 Aug 2023 06:13:28 +0000 (06:13 +0000)]
armsr: armv8: fix invalid symbol value for FSL_ENETC_QOS
The kernel FSL_ENETC_QOS option is only a compile time
option, it does not result in a separate module being built.
Set it to 'y' to resolve a warning from the kernel compile:
.config:2654:warning: symbol value 'm' invalid for FSL_ENETC_QOS
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Fixes: c3151b6f045 ("armvirt: 64: add support for other SystemReady-compatible vendors")
(cherry picked from commit
7770d08e2bd28c9c0dc0b3dc0aaf74074ad5772a)
Mathew McBride [Wed, 9 Aug 2023 07:20:07 +0000 (07:20 +0000)]
armsr: armv8: package and select MDIO driver for Thunder SoC's
This MDIO driver was already being built, but not installed due
to being selected by the ThunderX Ethernet driver.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
(cherry picked from commit
0018b335313ec7d866bf9e22273b620759e29598)
Mathew McBride [Wed, 9 Aug 2023 06:36:39 +0000 (06:36 +0000)]
armsr: add Marvell (Cavium) ThunderX2 network driver
The initial armv8 module incorrectly labelled the Thunder(v1) as
supporting the ThunderX2, when they have different drivers.
Add kmod-octeon-tx2 to support the newer devices.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
(cherry picked from commit
7c5bdff9c472a3f008ac15cc1ccb81cd23b20e1f)
Mathew McBride [Mon, 7 Aug 2023 05:06:43 +0000 (05:06 +0000)]
armsr: armv8: add bcmgenet (Raspberry Pi 4 GENET) to profile
kmod-bcmgenet is needed for Ethernet support on the
Raspberry Pi 4.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
(cherry picked from commit
911ee97774d2542300916f0e2763aa54c2a4dff1)
Mathew McBride [Fri, 23 Jun 2023 05:46:41 +0000 (05:46 +0000)]
armsr: armv8: add Broadcom GENET and MDIO modules
These are used by common Broadcom SoC's like
the BCM2711 (RPi4) and iProc network processor.
Tested on the RPi4B using the Raspberry Pi
UEFI+ACPI firmware[1].
Signed-off-by: Mathew McBride <matt@traverse.com.au>
[1] - https://github.com/pftf/RPi4
(cherry picked from commit
27ca83c6270a4cc6922cdae82bb5c01e4e2d1d22)
Mathew McBride [Thu, 10 Aug 2023 04:01:20 +0000 (04:01 +0000)]
armsr: armv8: enable AHCI/SATA controllers for mvebu,qoriq,juno
When comparing the generated OpenWrt .config to the Linux arm64
defconfig, I noticed these SATA controllers were not included.
As they may be used as a boot drive, they should be built into
the kernel.
CONFIG_SATA_MVEBU is for Marvell platforms.
CONFIG_SATA_QORIQ is for NXP Layerscape.
CONFIG_SATA_SIL24 is for Arm's Juno development board, see Linux
kernel commit
d7c38ff1cd86 ("arm64: defconfig: Add Juno SATA
controller").
Signed-off-by: Mathew McBride <matt@traverse.com.au>
(23.05/5.15 version of commit
9cb173e9f18da2530c3570479567d8130b05e5f8)
Mathew McBride [Thu, 10 Aug 2023 02:05:43 +0000 (02:05 +0000)]
armsr: armv8: synchronize PCIE related options with arm64 defconfig
This turns on various PCI related options which are enabled
in the Linux kernel arch/arm64/configs/defconfig but not
yet in the OpenWrt config.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
(23.05/5.15 version of commit
15d3536c9deb2927c9a39350c6fa2e59f859df2a)
Mathew McBride [Tue, 20 Jun 2023 03:30:51 +0000 (03:30 +0000)]
armsr: armv8: enable Broadcom arch'es
This is part of an effort to reduce differences between
the OpenWrt armsr/armv8 config and Linux arm64 defconfig.
This enables CONFIG_ARCH_BCM and downstream
CONFIG_ARCH_BCM2835 (= BCM2711 like Raspberry Pi 4)
and CONFIG_ARCH_BCM_IPROC (Broadcom iProc packet processors).
The broadband specific SoC's (ARCH_BCMBCA) are left out
as it is assumed these will not be doing EFI boot.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
(23.5/5.15 version of commit
df23eed17925b8cadccec53a784a12468a8a2e85)
Mathew McBride [Tue, 20 Jun 2023 01:53:23 +0000 (01:53 +0000)]
armsr: armv8: enable CONFIG_ARCH_RENESAS
Renesas markets several embedded Arm64 SoCs in the
RZ series (RZ/G, RZ/V), so should be enabled in
a general purpose target.
Automotive (R-Car) SoC's are not enabled by this change.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
(23.05/5.15 version of commit
1ff4f4df230166994c660ad77479f248223ce45b)
Mathew McBride [Mon, 14 Aug 2023 06:31:14 +0000 (06:31 +0000)]
armsr: enable ACPI_BUTTON
A review of the generated OpenWrt kernel .config
vs the Linux arm64 defconfig showed that this
option was not being enabled, as it is disabled
in OpenWrt's generic config.
ACPI_BUTTON is needed to report and respond to
power button events, so it should be enabled.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
(23.05/5.15 version of commit
c4c60e4b192180288aab577e166091c2d4c470af)
Mathew McBride [Tue, 20 Jun 2023 01:31:12 +0000 (01:31 +0000)]
armsr: armv8: sync CPU features, EFI, CMA and scheduler options with Linux defconfig
To bring the armsr/armv8 kernel configuration closer to the Linux
arm64 defconfig, synchronize options related to CPU features
(especially more recent Armv8.X variants), scheduler, EFI vars,
CMA and scheduler options.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
(23.05/5.15 version commit
22e0c7be47ca55b7366dc569926724271d51cb77)
Mathew McBride [Tue, 20 Jun 2023 01:23:17 +0000 (01:23 +0000)]
armsr: armv8: enable KVM host
x86/64 enables support for KVM so I can't see a reason why
not on armsr/armv8 as well.
Arm CPU errata workaround items related to virtualization
are also enabled by this change.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
(23.05/5.15 version of commit
e505873e65f72b5e89c136dbb61d992a2219b6eb)
Mathew McBride [Tue, 15 Aug 2023 03:47:23 +0000 (03:47 +0000)]
kernel: default ARM_PMU on for armsr/armv8
CONFIG_ARM_PMU (Arm Performance Monitor Unit) is a requirement
to use KVM (virtualization) from Linux 5.11+, as the virtualised
guest has virtualized PMU access.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
(cherry picked from commit
76d4a7c84a97a5555b1962ddb9fc694b7e1f6ba8)
Mathew McBride [Wed, 7 Jun 2023 01:04:03 +0000 (01:04 +0000)]
armsr: armv8: sync Arm64 erratum options with kernel defconfig
To reduce differences with the Linux arm64 defconfig,
sync the enabled erratum items with defconfig.
There are still some options not selected due to
CONFIG_KVM or other options not enabled in OpenWrt
by default.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
(23.05/5.15 version of commit
5c4239ac3f189352698de706599bc32a6e457532)
Tianling Shen [Tue, 23 May 2023 07:43:14 +0000 (15:43 +0800)]
kernel: modules: add xdp-sockets-diag support
Support for PF_XDP sockets monitoring interface used by the ss tool.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit
06e64f9b364abe15c27bf0a7225fcac740819668)
John Audia [Wed, 16 Aug 2023 19:15:17 +0000 (15:15 -0400)]
kernel: bump 5.15 to 5.15.127
Changelog: https://cdn.kernel.org/pub/linux/kernel/v5.x/ChangeLog-5.15.127
All patches automatically rebased.
Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3
Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit
973c5d4a1d5d732f46b577384f39da2336a80fb1)
Hauke Mehrtens [Mon, 14 Aug 2023 21:33:49 +0000 (23:33 +0200)]
scripts: qemustart: Fix x86/legacy bootup
The ide-drive option was renamed to ide-hd in qemu 6.0.
With this change qemu is starting again on Debian 12.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit
497012ab4eb1f37cbbbff9a766d2fecdb43dd0db)
Hauke Mehrtens [Sun, 13 Aug 2023 21:02:03 +0000 (23:02 +0200)]
x86: Add virtualization time sync support
This compiles the CONFIG_PTP_1588_CLOCK support into the kernel binary
and activates the drivers for KVM and VMware which allow syncing the
host time with the VM when OpenWrt is running in a VM. With this change
the CONFIG_HYPERV_UTILS driver is now build into the kernel, because it
depends on the PTP framework being compiled in. CONFIG_HYPERV_UTILS was
build as a module, but not packages before.
Fixes: #13277
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit
54d470ed0ecaff9e8084c013ddbc95e8afc3ab42)
Hauke Mehrtens [Sun, 13 Aug 2023 20:50:19 +0000 (22:50 +0200)]
x86: Activate CONFIG_PCIEASPM
This activates PCI Express ASPM control in Linux. Without this option it
is completely controlled by the BIOS, now Linux will take over and apply
some workarounds if needed.
Fixes: #13248
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit
ff71035751bf440401b4bbc32e0b61ba11178234)
Ivan Pavlov [Wed, 2 Aug 2023 05:53:23 +0000 (08:53 +0300)]
uboot-envtools: add u-boot env config for Xiaomi mi-mini
Add u-boot env config for Xiaomi mi-mini for using fw_printenv and fw_setenv on this board
Signed-off-by: Ivan Pavlov <AuthorReflex@gmail.com>
(cherry picked from commit
a87bc138cfccd8de06afaad81f7ba838a87fe4f8)
Ivan Pavlov [Wed, 2 Aug 2023 05:23:02 +0000 (08:23 +0300)]
ramips: improve Xiaomi mi-mini indications
Sets status indications led color on Xiaomi mi-mini router as other Xiaomi routers
Signed-off-by: Ivan Pavlov <AuthorReflex@gmail.com>
(cherry picked from commit
54e5e396c59948224dfb8ccf7aa8afe11462f647)
Robert Marko [Mon, 14 Aug 2023 11:50:47 +0000 (13:50 +0200)]
ipq40xx: meraki: define DTB load address
It seems that the Meraki bootloader does not respect the kernel ARM booting
specification[1] that requires that address where DTB is located needs to
be 64-bit aligned and often places the DTB on a non 64-bit aligned address
and then kernel fails to find the DTB magic and fails to boot.
Even worse, there is no prints until early printk is enabled and then its
visible that kernel is trying to find the ATAG-s as DTB was not found or
is invalid.
Unifi 6 devices had the same issue and it can be solved by passing the
load adress as part of the FIT image.
It seems that the vendor was aware of the issue and is always relocating
the DTB to 0x89000000, so lets just do the same.
Now that booting is reliable, reenable default images for the Meraki MR33
and MR74 devices.
Reviewed-by: Lech Perczak lech.perczak@gmail.com
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit
f1c80445bd7e3b2f7fc3e4c8136402b30834d4e9)
Robert Marko [Mon, 14 Aug 2023 11:48:37 +0000 (13:48 +0200)]
ipq40xx: meraki: remove swconfig in DEVICE_PACKAGES
ipq40xx was converted to DSA and swconfig is not being included at all in
the default packages so there is no need to drop it from device packages.
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit
bb4a25860f593790aaedc1b31dde33fbc519e7bf)
Robert Marko [Mon, 14 Aug 2023 11:47:49 +0000 (13:47 +0200)]
ipq40xx: commonize Meraki recipe
MR33 and MR74 share pretty much everything in the image recipe, so lets
extract a common recipe to avoid duplication.
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit
9e9dc1890c6f58d858208136ecfa435445dfca09)
Hauke Mehrtens [Sun, 13 Aug 2023 20:32:20 +0000 (22:32 +0200)]
linux-firmware: Update Intel AX200 and AX210 firmware
This updates the Intel iwlwifi firmware for AX200 and AX210 from version
66 to version 72. Version 72 is the latest version supported by iwlwifi
from kernel 6.1.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit
00ce1c05877ac38f5ff00c1c2ce3468d5168f76c)
Hauke Mehrtens [Sat, 12 Aug 2023 13:14:22 +0000 (15:14 +0200)]
patchelf: Revert "tools/patchelf: update to 0.18.0"
This reverts commit
ec6bcda8e49815efeee845da50defc85ae068b79.
patchelf 0.18.0 requires GCC 8, it does not compile using GCC 7 any
more. Downgrade to patchelf 0.17.2 which still supports GCC 7.
Downgrade patchelf to 0.17.2 only in the OpenWrt 23.05 branch and
require GCC 8 in the master branch.
Ubuntu 18.04 uses GCC 7 by default.
Fixes: #13102
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
John Audia [Fri, 11 Aug 2023 18:48:41 +0000 (14:48 -0400)]
kernel: bump 5.15 to 5.15.126
1. Disable unneeded errata Kconfig symbols
2. Update kernel
Changelog: https://lore.kernel.org/stable/
2023081111-unlocking-synopsis-d7d5@gregkh/
All patches automatically rebased.
Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3
Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit
64782497dbdf124d9f7979ae1aa48f20c9b9dec8)
Felix Fietkau [Fri, 14 Jul 2023 08:01:30 +0000 (10:01 +0200)]
hostapd: add fix for dealing with VHT 160 MHz via ext nss bw
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit
adfeda849198b33ffa7a7ef233ae8a4df22bbc2d)
Daniel Golle [Sun, 13 Aug 2023 13:52:44 +0000 (14:52 +0100)]
generic: backport fix for Winbond SPI NAND
Avoid using stack allocated memory for DMA operations.
Fixes: 156c00dedc ("generic: backport Winbond W25N02KV SPI-NAND support")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit
e6f8b699189139f09c3685332310ff870610de5e)
Daniel Golle [Sun, 13 Aug 2023 13:57:10 +0000 (14:57 +0100)]
generic: 5.15: rename patches to match correct version
Rename two patches which were only accepted in Linux 6.2, but were
marked as if they were accepted in Linux 6.1.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit
42e14d3ed870e56c29bff84ce686839d9bab2034)
Daniel Golle [Fri, 11 Aug 2023 13:16:08 +0000 (14:16 +0100)]
armsr: remove redundant phy-marvell-10g module
the Marvell 10G PHY driver is no way specific to ARM SystemReady
systems, it frequently occurs on SFP+ copper modules and is useful on
many targets.
Hence it been added to package/kernel/linux/modules/netdevices and we
can remove the now redundant target-specific module.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit
c524a76f4c09a4e3fa4572612d336b4ef7ff2fb8)
Daniel Golle [Wed, 9 Aug 2023 11:21:41 +0000 (12:21 +0100)]
uboot-mediatek: bpi-r3: prepare for larger FIT structures
Instead of reading only a single 4kiB page, read the first 128kiB to
determine the size of an uImage.FIT using 'imsz' or 'imszb'.
This will be needed once we add more Device Tree Overlays, which may
happen for the BPi-R3 mini.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit
3c2f7bb555c2cd5c4be8aed11b9d31b48cc0bcf8)
Daniel Golle [Fri, 4 Aug 2023 13:07:43 +0000 (14:07 +0100)]
mediatek: filogic: mt7988: mark RTC clock as critical
A dependency of the MT7988 MMC host controller on the SoC's RTC clock
being running has been discovered. Mark RTC clock as critical to fix
MMC host on MT7988.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit
0454691960e16bb93ed01f89352cbb375008aaf5)
Felix Fietkau [Mon, 31 Jul 2023 10:41:13 +0000 (12:41 +0200)]
arm-trusted-firmware-tools: fix build on macOS/Darwin
Resolve conflicts with the uuid type from darwin system headers
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit
16c37ba9136ff431c7e3c97cc27e4ea166b8020a)
Hauke Mehrtens [Fri, 11 Aug 2023 09:38:29 +0000 (11:38 +0200)]
firmware: intel-microcode: update to
20230808
Debian changelog:
intel-microcode (3.
20230808.1) unstable; urgency=high
* New upstream microcode datafile
20230808 (closes: #
1043305)
Mitigations for "Downfall" INTEL-SA-00828 (CVE-2022-40982),
INTEL-SA-00836 (CVE-2023-23908) and INTEL-SA-00837 (CVE-2022-41804)
* Updated microcodes:
sig 0x00050653, pf_mask 0x97, 2023-03-23, rev 0x1000181, size 36864
sig 0x00050654, pf_mask 0xb7, 2023-03-06, rev 0x2007006, size 44032
sig 0x00050656, pf_mask 0xbf, 2023-03-17, rev 0x4003604, size 38912
sig 0x00050657, pf_mask 0xbf, 2023-03-17, rev 0x5003604, size 38912
sig 0x0005065b, pf_mask 0xbf, 2023-03-21, rev 0x7002703, size 30720
sig 0x000606a6, pf_mask 0x87, 2023-03-30, rev 0xd0003a5, size 297984
sig 0x000706e5, pf_mask 0x80, 2023-02-26, rev 0x00bc, size 113664
sig 0x000806c1, pf_mask 0x80, 2023-02-27, rev 0x00ac, size 111616
sig 0x000806c2, pf_mask 0xc2, 2023-02-27, rev 0x002c, size 98304
sig 0x000806d1, pf_mask 0xc2, 2023-02-27, rev 0x0046, size 103424
sig 0x000806e9, pf_mask 0xc0, 2023-02-22, rev 0x00f4, size 106496
sig 0x000806e9, pf_mask 0x10, 2023-02-23, rev 0x00f4, size 105472
sig 0x000806ea, pf_mask 0xc0, 2023-02-23, rev 0x00f4, size 105472
sig 0x000806eb, pf_mask 0xd0, 2023-02-23, rev 0x00f4, size 106496
sig 0x000806ec, pf_mask 0x94, 2023-02-26, rev 0x00f8, size 106496
sig 0x000806f8, pf_mask 0x87, 2023-05-09, rev 0x2b0004b1, size 572416
sig 0x000806f7, pf_mask 0x87, 2023-05-09, rev 0x2b0004b1
sig 0x000806f6, pf_mask 0x87, 2023-05-09, rev 0x2b0004b1
sig 0x000806f5, pf_mask 0x87, 2023-05-09, rev 0x2b0004b1
sig 0x000806f4, pf_mask 0x87, 2023-05-09, rev 0x2b0004b1
sig 0x000806f8, pf_mask 0x10, 2023-05-15, rev 0x2c000271, size 605184
sig 0x000806f6, pf_mask 0x10, 2023-05-15, rev 0x2c000271
sig 0x000806f5, pf_mask 0x10, 2023-05-15, rev 0x2c000271
sig 0x000806f4, pf_mask 0x10, 2023-05-15, rev 0x2c000271
sig 0x00090672, pf_mask 0x07, 2023-04-18, rev 0x002e, size 220160
sig 0x00090675, pf_mask 0x07, 2023-04-18, rev 0x002e
sig 0x000b06f2, pf_mask 0x07, 2023-04-18, rev 0x002e
sig 0x000b06f5, pf_mask 0x07, 2023-04-18, rev 0x002e
sig 0x000906a3, pf_mask 0x80, 2023-04-18, rev 0x042c, size 219136
sig 0x000906a4, pf_mask 0x80, 2023-04-18, rev 0x042c
sig 0x000906e9, pf_mask 0x2a, 2023-02-23, rev 0x00f4, size 108544
sig 0x000906ea, pf_mask 0x22, 2023-02-23, rev 0x00f4, size 104448
sig 0x000906eb, pf_mask 0x02, 2023-02-23, rev 0x00f4, size 106496
sig 0x000906ec, pf_mask 0x22, 2023-02-23, rev 0x00f4, size 105472
sig 0x000906ed, pf_mask 0x22, 2023-02-27, rev 0x00fa, size 106496
sig 0x000a0652, pf_mask 0x20, 2023-02-23, rev 0x00f8, size 97280
sig 0x000a0653, pf_mask 0x22, 2023-02-23, rev 0x00f8, size 97280
sig 0x000a0655, pf_mask 0x22, 2023-02-23, rev 0x00f8, size 97280
sig 0x000a0660, pf_mask 0x80, 2023-02-23, rev 0x00f8, size 97280
sig 0x000a0661, pf_mask 0x80, 2023-02-23, rev 0x00f8, size 96256
sig 0x000a0671, pf_mask 0x02, 2023-02-26, rev 0x0059, size 104448
sig 0x000b0671, pf_mask 0x32, 2023-06-06, rev 0x0119, size 210944
sig 0x000b06a2, pf_mask 0xe0, 2023-06-06, rev 0x4119, size 216064
sig 0x000b06a3, pf_mask 0xe0, 2023-06-06, rev 0x4119
sig 0x000b06e0, pf_mask 0x11, 2023-04-12, rev 0x0011, size 136192
* source: update symlinks to reflect id of the latest release,
20230808
intel-microcode (3.
20230512.1) unstable; urgency=medium
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit
ced285487144e1138e3d2b986b3e070a9b4fd412)
Hauke Mehrtens [Thu, 10 Aug 2023 15:50:38 +0000 (17:50 +0200)]
linux-firmware: update to
20230804
7be2766 (tag:
20230804) Merge branch 'rb3-update' of https://github.com/lumag/linux-firmware
66c1db8 Merge https://github.com/pkshih/linux-firmware
5046942 Mellanox: Add new mlxsw_spectrum firmware xx.2012.1012
5c7b67f linux-firmware: Add URL for latest FW binaries for NXP BT chipsets
29f185d rtw89: 8851b: update firmware to v0.29.41.1
742bf57 qcom: sdm845: add RB3 sensors DSP firmware
253cc17 amdgpu: Update DMCUB for DCN314 & Yellow Carp
07f05b0 Merge branch 'dmc-adlp_2.20-mtl_2.13' of git://anongit.freedesktop.org/drm/drm-firmware
5a251ed Merge branch 'for-upstream' of https://github.com/CirrusLogic/linux-firmware
6c8ce49 ice: add LAG-supporting DDP package
fd6e13c i915: Update MTL DMC to v2.13
41e615c i915: Update ADLP DMC to v2.20
c8424cf cirrus: Add CS35L41 firmware for Dell Oasis Models
b6ea35f copy-firmware: Fix linking directories when using compression
0a51959 copy-firmware: Fix test: unexpected operator
b602d43 qcom: sc8280xp: LENOVO: remove directory sym link
e0bad5e qcom: sc8280xp: LENOVO: Remove execute bits
59fbffa amdgpu: update VCN 4.0.0 firmware
22fb12f amdgpu: add initial SMU 13.0.10 firmware
b3f512f amdgpu: add initial SDMA 6.0.3 firmware
b1a7d76 amdgpu: add initial PSP 13.0.10 firmware
d6d655a amdgpu: add initial GC 11.0.3 firmware
c782458 Merge branch 'v2.0.21961' of https://github.com/yunfei-mtk/linux_fw_10bit
ca9086f Merge branch 'dg2_mtl_guc_70.8' of git://anongit.freedesktop.org/drm/drm-firmware
0bc3126 linux-firmware: Update AMD fam17h cpu microcode
b250b32 linux-firmware: Update AMD cpu microcode
9dfcace amdgpu: update green sardine VCN firmware
b519832 amdgpu: update renoir VCN firmware
5f569aa amdgpu: update raven VCN firmware
868bb36 amdgpu: update raven2 VCN firmware
6fa9a17 amdgpu: update Picasso VCN firmware
cd52460 amdgpu: update DMCUB to v0.0.175.0 for various AMDGPU ASICs
4ef7581 Updated NXP SR150 UWB firmware
2514504 Merge branch 'for-upstream' of https://github.com/CirrusLogic/linux-firmware
45f5ebf wfx: update to firmware 3.16.1
f41d890 mediatek: Update mt8195 SCP firmware to support 10bit mode
6f3a37f i915: update DG2 GuC to v70.8.0
0ee23bd i915: update to GuC 70.8.0 and HuC 8.5.1 for MTL
1a76e8b cirrus: Add CS35L41 firmware for ASUS ROG 2023 Models
d3f6606 Partially revert "amdgpu: DMCUB updates for DCN 3.1.4 and 3.1.5"
8917650 linux-firmware: update firmware for mediatek bluetooth chip (MT7922)
7d9af09 linux-firmware: update firmware for MT7922 WiFi device
0bab5df Merge tag 'iwlwifi-fw-2023-06-29' of http://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/linux-firmware
3ec3817 linux-firmware: Update firmware file for Intel Bluetooth AX203
7db3ef9 linux-firmware: Update firmware file for Intel Bluetooth AX203
5684048 linux-firmware: Update firmware file for Intel Bluetooth AX211
3f7a24e linux-firmware: Update firmware file for Intel Bluetooth AX211
eb2c745 linux-firmware: Update firmware file for Intel Bluetooth AX210
4a3ff0a linux-firmware: Update firmware file for Intel Bluetooth AX200
1d1bad4 linux-firmware: Update firmware file for Intel Bluetooth AX201
db39dff Fix qcom ASoC tglp WHENCE entry
a687f89 Merge branch 'sc8280xp-audio-fw' of git://git.kernel.org/pub/scm/linux/kernel/git/srini/linux-firmware
9e0343c check_whence: Check link targets are valid
b255f5b iwlwifi: add new FWs from core80-39 release
fa5d30b iwlwifi: update cc/Qu/QuZ firmwares for core80-39 release
f9a35b3 qcom: Add Audio firmware for SC8280XP X13s
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit
bfbb5ccf7a55ed2cc574405f7f83da5e48811401)
Hauke Mehrtens [Thu, 10 Aug 2023 16:03:43 +0000 (18:03 +0200)]
mbedtls: Update to version 2.28.4
This only fixes minor problems.
Changelog: https://github.com/Mbed-TLS/mbedtls/releases/tag/v2.28.4
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit
d773fe5411cd4fdd8e107cfe338ed731001a1ade)
Hauke Mehrtens [Thu, 10 Aug 2023 18:59:11 +0000 (20:59 +0200)]
uci: update to git HEAD
3cda251 file: Fix uci -m import command
5781664 remove internal usage of redundant uci_ptr.last
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit
d1427863bae1603eb3b8b385024f7ca11297503d)
Tomasz Maciej Nowak [Fri, 7 Jul 2023 19:13:35 +0000 (21:13 +0200)]
mvebu: mcbin-singleshot: enable hearbeat LED by default
This has been a part of modified upstream patch but got lost on major
kernel bump to 5.15, so bring it back.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
[Add patch for kernel 6.1 too]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit
5e6bab661a1028d583338c5823f6a3b9d6444ce0)
Alexandru Gagniuc [Thu, 27 Jul 2023 15:51:33 +0000 (10:51 -0500)]
kernel: netsupport: Add kmod-sched-skbprio
Add support for the SKBPRIO queuing discipline. This is subtly
different than prio as it also drops packets from the lower priority
flows.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
(cherry picked from commit
8fba9afda5f514afa48a216514b3f0b0fb22afac)
Luca Barbato [Sun, 23 Jul 2023 20:23:40 +0000 (22:23 +0200)]
kernel: Autoload nvme at preinit time
This way is possible to mount nvme extroots.
Signed-off-by: Luca Barbato <lu_zero@gentoo.org>
(cherry picked from commit
0fe9a8ca94830270820f7a1eb457f5d5d587125d)
Felix Baumann [Mon, 3 Jul 2023 23:35:43 +0000 (01:35 +0200)]
ath79: move ubnt-xm 64M RAM boards back to generic
return ubnt_rocket-m and ubnt_powerbridge-m back to ath79-generic
They have enough RAM-ressources to not be considered as tiny.
This reverts the commit
f4415f7635164ec07ddc22f56df93555804b5767 partially
Signed-off-by: Felix Baumann <felix.bau@gmx.de>
(cherry picked from commit
9e86a96af5ecea6e73fa463d6cfa4408e2b49d35)
Javier Marcet [Sun, 9 Jul 2023 15:55:48 +0000 (17:55 +0200)]
perf: opt-out of lto usage
This fixes building with USE_LTO enabled:
mold: error: undefined symbol: __memset
>>> referenced by <artificial>
>>> ./tmp/ccsgR7G6.ltrans10.ltrans.o
mold: error: undefined symbol: memset_orig
>>> referenced by <artificial>
>>> ./tmp/ccsgR7G6.ltrans10.ltrans.o
mold: error: undefined symbol: perf_regs_load
>>> referenced by <artificial>
>>> ./tmp/ccsgR7G6.ltrans15.ltrans.o:(test_dwarf_unwind__thread)
mold: error: undefined symbol: memset_erms
>>> referenced by <artificial>
>>> ./tmp/ccsgR7G6.ltrans10.ltrans.o
mold: error: undefined symbol: memcpy_orig
>>> referenced by <artificial>
>>> ./tmp/ccsgR7G6.ltrans10.ltrans.o
mold: error: undefined symbol: memcpy_erms
>>> referenced by <artificial>
>>> ./tmp/ccsgR7G6.ltrans10.ltrans.o
mold: error: undefined symbol: __memcpy
>>> referenced by <artificial>
>>> ./tmp/ccsgR7G6.ltrans10.ltrans.o
collect2: error: ld returned 1 exit status
make[5]: *** [Makefile.perf:670: ../openwrt/linux/tools/perf-target-x86_64_musl/perf] Error 1
make[4]: *** [Makefile.perf:238: sub-make] Error 2
make[3]: *** [Makefile:70: all] Error 2
make[2]: *** [Makefile:84: ./build_dir/target-x86_64_musl/linux-x86_64/linux-5.15.120/tools/perf-target-x86_64_musl/.built] Error 2
make[2]: Leaving directory './package/devel/perf'
time: package/devel/perf/compile#55.88#6.78#12.89
ERROR: package/devel/perf failed to build.
Signed-off-by: Javier Marcet <javier@marcet.info>
(cherry picked from commit
5ed185bfbd9719ef3b114fa6faeb343ac87b2490)
Matthias Van Parys [Tue, 11 Jul 2023 08:47:53 +0000 (10:47 +0200)]
fortify-headers: add __extension__ mark to strings.h
Add the __extension__ mark before #include_next in strings.h
to avoid a compiler error when -pedantic is enabled.
This has been done for all other headers in the past.
Signed-off-by: Matthias Van Parys <matthias.vanparys@softathome.com>
(cherry picked from commit
2425d6df121082a8643459ac7996334779792a59)
Oskari Rauta [Tue, 11 Jul 2023 18:06:30 +0000 (21:06 +0300)]
util-linux: enable colrm util as package
colrm is already built, package just isn't generated.
colrm can be used to remove columns from file/stdin.
Use cases vary, personally I needed it because I build openwrt
natively - and wolfssl configure script wants either colrm, or cut
but busybox's cut isn't accepted.
Built: x86_64, latest git
Tested: x86_64, latest git
Signed-off-by: Oskari Rauta <oskari.rauta@gmail.com>
(cherry picked from commit
e21b4c9636d5dc07b303aa568cbf31b76f244397)
Adam Bailey [Tue, 4 Jul 2023 01:16:14 +0000 (20:16 -0500)]
lua: fix integer overflow in LNUM patch
Safely detect integer overflow in try_addint() and try_subint().
Old code relied on undefined behavior, and recent versions of GCC on x86
optimized away the if-statements.
This caused integer overflow in Lua code instead of falling back to
floating-point numbers.
Signed-off-by: Adam Bailey <aebailey@gmail.com>
(cherry picked from commit
3a2e7c30d3e6a187ba1df740cdb24c8ad84dfe48)
Martin Schiller [Fri, 7 Jul 2023 11:29:45 +0000 (13:29 +0200)]
e2fsprogs: do not symlink tune2fs to findfs
commit
c0611b45a998 ("e2fsprogs: symlink e2fsck to fsck.ext{2, 3, 4},
and tune2fs to findfs") introduced a symlink from tune2fs to findfs.
This only works when the included private libblkid library is used, but
commit
5b1660a5387b ("utils/e2fsprogs: Update to 1.43.6") disabled the
usage of this private lib and enabled the shared lib support.
Removing this symlink makes it possible to install tune2fs and findfs
package.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
(cherry picked from commit
0b80c5725fd70bfd23701cd49fa9f252f6835506)
Hauke Mehrtens [Sat, 1 Jul 2023 10:14:07 +0000 (12:14 +0200)]
rpcd: update to latest git HEAD
c07ab2f iwinfo: update byte counter to 64bit
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit
2486841c1bc7c3267e409b510e142e04cc5f0a5b)
Hauke Mehrtens [Sun, 25 Jun 2023 18:09:38 +0000 (20:09 +0200)]
rpcd: update to latest git HEAD
31c3907 file: strengthen exec access control
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit
9d8d65322ce7d82ee20cc6dcca07506e7405c5f5)
Hauke Mehrtens [Sat, 1 Jul 2023 10:08:51 +0000 (12:08 +0200)]
iwinfo: update to latest git HEAD
d1f07cf devices: add device id for Atheros AR9287 and AR9380
65ea345 nl80211: constify a few arrays
ca79f64 lib: report byte counters as 64 bit values
This contains an ABI change, increase the ABI version too.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit
a226153067766db6d733aa3e330742c9da40c4f6)
Hauke Mehrtens [Sun, 25 Jun 2023 19:46:45 +0000 (21:46 +0200)]
procd: update to latest git HEAD
122a5e3 Revert "sysupgrade: print errno on failure"
2db8365 system: add RISC-V CPU info
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit
359638098742d7573ff422f6dc7125c89086072b)
John Audia [Tue, 8 Aug 2023 23:57:20 +0000 (19:57 -0400)]
kernel: bump 5.15 to 5.15.125
1. Add new symbols to generic config
2. Bump kernel
Changelog: https://lore.kernel.org/stable/
2023080818-groin-gradient-a031@gregkh/
All patches automatically rebased.
Signed-off-by: John Audia <therealgraysky@proton.me>
[Refreshed on top of OpenWrt 23.05]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit
daed3322d347cae5fa538907b5f1fa5d5cfc08c6)
John Audia [Thu, 3 Aug 2023 17:53:47 +0000 (13:53 -0400)]
kernel: bump 5.15 to 5.15.124
Changelog: https://lore.kernel.org/stable/
2023080341-curliness-salary-4158@gregkh/
1. Needed to make a change to to package/kernel/linux/modules/netsupport.mk
due to upstream moving vxlan to its own directory[1]. @john-tho suggested
using the the 6.1 xvlan FILES to circumvent.
2. All patches automatically rebased.
1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.124&id=
77396fa9096abdbfbb87d63e73ad44d5621cf103
Signed-off-by: John Audia <therealgraysky@proton.me>
[Refreshed on top of OpenWrt 23.05]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit
81c1172c3626157ff9a146430cd14e32c9c80a5a)