rt2800: comment and simplify AGC init for RT6352

We do not need separate lines for calculating register values.
Also add comment that value is different than in vendor driver.

Suggested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rt2800: enable TX_PIN_CFG_RFRX_EN only for MT7620

The TX_PIN_CFG_RFRX_EN bit was not set on other devices than MT7620,
restore old behavaviour since setting this bit maight not be
correct for older devices.

Fixes: 41977e86c984 ("rt2x00: add support for MT7620")
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rt2800: enable TX_PIN_CFG_LNA_PE_ bits per band

Do not enable TX_PIN_CFG_LNA_PE_A* bits for 2.4GHz band and
vice versa TX_PIN_CFG_LNA_PE_G* bits for 5GHz.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rt2x00: remove confusing AGC register

Register 66 was causing issues on RT6352 if set to the same value as
in MTK driver. With 1c reg value device was working fine in both HT20
and HT40 modes.

Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rt2x00: remove unneeded check

Remove band check from rf53xx channel config routine since all chips
using it are single band.

Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

carl9170: clean up a clamp() call

The parameter order for clamp is supposed to be clamp(value, low, high).
When we write it in this order it's equivalent to
min(head->plcp[3] & 0x7f, 75) which works in this context where the min
is zero.  But it's not a correct use of the API.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtl818x_pci: Remove set but not used variables 'io_addr, mem_addr'

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/net/wireless/realtek/rtl818x/rtl8180/dev.c: In function 'rtl8180_probe':
drivers/net/wireless/realtek/rtl818x/rtl8180/dev.c:1727:15: warning:
 variable 'io_addr' set but not used [-Wunused-but-set-variable]

drivers/net/wireless/realtek/rtl818x/rtl8180/dev.c:1726:16: warning:
 variable 'mem_addr' set but not used [-Wunused-but-set-variable]

They're never used since introduction.

Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

orinoco : Replace function name in string with __func__

Replace hard coded function name with __func__, to
improve robustness and to conform to the Linux kernel coding
style. Issue found using checkpatch.

Signed-off-by: Keyur Patel <iamkeyur96@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: don't advertise IBSS features without FW support

As it is, doing something like

  # iw phy phy0 interface add foobar type ibss

on a firmware that doesn't have ad-hoc support just yields failures of
HostCmd_CMD_SET_BSS_MODE, which happened to return a '-1' error code
(-EPERM? not really right...) and sometimes may even crash the firmware
along the way.

Let's parse the firmware capability flag while registering the wiphy, so
we don't allow attempting IBSS at all, and we get a proper -EOPNOTSUPP
from nl80211 instead.

Fixes: e267e71e68ae ("mwifiex: Disable adhoc feature based on firmware capability")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: Fix NL80211_TX_POWER_LIMITED

NL80211_TX_POWER_LIMITED was treated as NL80211_TX_POWER_AUTOMATIC,
which is the opposite of what should happen and can cause nasty
regulatory problems.

if/else converted to a switch without default to make gcc warn
on unhandled enum values.

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

libertas_tf: remove set but not used variable 'flags'

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/net/wireless/marvell/libertas_tf/main.c: In function 'lbtf_rx':
drivers/net/wireless/marvell/libertas_tf/main.c:554:15: warning:
 variable 'flags' set but not used [-Wunused-but-set-variable]

It never used and can be removed.

Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Steve deRosier <derosier@cal-sierra.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

libertas_tf: fix signal reporting

Instead of exposing the signal-to-noise ration, calculate the actual signal
level taking the noise floor into account.

Also, flip the SIGNAL_DBM bit on, so that mac80211 exposes the signal
level along with the station info in scan results. This fills
NetworkManager's "nmcli d wifi output" output with colors, bars and joy.

Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-by: Steve deRosier <derosier@cal-sierra.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

libertas_tf: move the banner to a more appropriate place

Also, turn it to a dev_info() to make checkpatch.pl happy.

Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-by: Steve deRosier <derosier@cal-sierra.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

libertas_tf: don't set URB_ZERO_PACKET on IN USB transfer

It doesn't make sense and the USB core warns on each submit of such
URB, easily flooding the message buffer with tracebacks.

Analogous issue was fixed in regular libertas driver in commit 6528d8804780
("libertas: don't set URB_ZERO_PACKET on IN USB transfer").

Cc: stable@vger.kernel.org
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-by: Steve deRosier <derosier@cal-sierra.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

libertas_tf: lower the debug level of command trace

Logging each and every command response is way too much for INFO level.
Silence this, unless CONFIG_LIBERTAS_THINFIRM_DEBUG has been enabled.

Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-by: Steve deRosier <derosier@cal-sierra.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rsi: remove set but not used variables 'info, vif'

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/net/wireless/rsi/rsi_91x_main.c: In function 'rsi_prepare_skb':
drivers/net/wireless/rsi/rsi_91x_main.c:127:24: warning:
 variable 'vif' set but not used [-Wunused-but-set-variable]

drivers/net/wireless/rsi/rsi_91x_main.c:124:28: warning:
 variable 'info' set but not used [-Wunused-but-set-variable]

They're not used any more since 160ee2a11ce0 ("rsi: fill rx_params only once.")

Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rsi: fix spelling mistakes

Trivial fixes to spelling mistakes in various files in rsi folder.

Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rsi: fix a typo in a debug message

There is a \b (backspace) character in the message that wasn't intended.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: remove set but not used variable 'old_state'

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/net/wireless/broadcom/brcm80211/brcmfmac/usb.c: In function 'brcmf_usb_state_change':
drivers/net/wireless/broadcom/brcm80211/brcmfmac/usb.c:578:6: warning:
 variable 'old_state' set but not used [-Wunused-but-set-variable]

It's never used and can be removed.

Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: rework bphy_err() to take struct brcmf_pub argument

This macro will be used in more places not just the cfg80211.c. It makes
sense to pass some common struct to it as "struct wiphy" is mostly
referenced in cfg80211 code only.

A very common one (used above the bus abstraction layer) is struct
brcmf_pub. Many functions already keep reference to it which will make
using bphy_err() simpler. It should also allow extending that macro's
logic if it's ever needed.

This improves code recently added in the commit 3ef005b82e2a ("brcmfmac:
add bphy_err() and use it in the cfg80211.c").

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: support firmware reporting 160 MHz channels

So far 160 MHz channels were treated as 20 MHz ones which was breaking
support for 40/80 MHz due to the brcmf_construct_chaninfo() logic and
its assumptions.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: improve code handling bandwidth of firmware reported channels

1) Use switch to simplify/improve the code & avoid some duplication
2) Add warning for unsupported values

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: print firmware reported ring status errors

Firmware is capable of reporting ring status. It's used e.g. to signal
some problem with a specific ring setup. This patch adds support for
printing ring & error number which may be useful for debugging setup
issues.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: use chipname in brcmf_fw_alloc_request() for error path as well

The local variable chipname is string representation of chip id and revision
which is printed in the good flow of brcmf_fw_alloc_request(). Also use it
for the error path, ie. for unknown/unsupported devices.

Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: check and dump trap info during sdio probe

When the firmware crashes during the probe sequence we provide little
information on what really failed. This patch checks the sdpcm shared
location and show the trap information if a firmware trap has happened.

Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: disable MBSS feature for bcm4330 device

The MBSS feature was already disabled for bcm43362 as it resulted in a
beacon with BRCM_TEST_SSID regardless user configuration in hostapd. Now
the same has been reported for bcm4330 so disable the feature for this
device as well.

Reported-by: Russell King <linux@armlinux.org.uk>
Tested-by: Christopher Martin <chrsmrtn@gmail.com>
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: create debugfs files for bus-specific layer

Since we moved the drivers debugfs directory under ieee80211 debugfs the
debugfs entries need to be added after wiphy_register() has been called.
For most part that has been done accordingly, but for the debugfs entries
added by SDIO it was not and failed silently. This patch fixes that by
adding a bus-layer callback for it.

Fixes: 856d5a011c86 ("brcmfmac: allocate struct brcmf_pub instance using wiphy_new()")
Reported-by: Russel King <linux@armlinux.org.uk>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: add subtype check for event handling in data path

For USB there is no separate channel being used to pass events
from firmware to the host driver and as such are passed over the
data path. In order to detect mock event messages an additional
check is needed on event subtype. This check is added conditionally
using unlikely() keyword.

Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: assure SSID length from firmware is limited

The SSID length as received from firmware should not exceed
IEEE80211_MAX_SSID_LEN as that would result in heap overflow.

Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: rtl8821ae: Remove CamelCase variables

If a macro is in CamelCase, it it converted to upper case. Variables
and routine names are converted to lower case.

The following checkpatch exceptions are also fixed:

WARNING: line over 80 characters
#316: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8821ae/fw.c:1751:
+       SET_8821AE_H2CCMD_AOAC_RSVDPAGE_LOC_GTK_EXT_MEM(u1rsvdpageloc2, GTKEXT_PG);

CHECK: spaces preferred around that '+' (ctx:VxV)
#357: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8821ae/hw.c:2591:
+                (eeaddr+1), hwinfo[eeaddr+1]);
                        ^

CHECK: spaces preferred around that '+' (ctx:VxV)
#357: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8821ae/hw.c:2591:
+                (eeaddr+1), hwinfo[eeaddr+1]);
                                          ^

CHECK: spaces preferred around that '+' (ctx:VxV)
#358: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8821ae/hw.c:2592:
+       if (0xFF == hwinfo[eeaddr+1])  /*YJ,add,120316*/
                                 ^

WARNING: Comparisons should place the constant on the right side of the test
#358: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8821ae/hw.c:2592:
+       if (0xFF == hwinfo[eeaddr+1])  /*YJ,add,120316*/

CHECK: spaces preferred around that '&' (ctx:VxV)
#501: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8821ae/hw.c:2666:
+                               pwrinfo24g->bw40_diff[rfpath][txcount] = (hwinfo[eeaddr]&0xf0) >> 4;
                                                                                        ^
Note that not all checkpatch exceptions are addressed. Those will be
handled in later patches.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: rtl8723{be,ae}: Remove CamelCase variables

If a macro is in CamelCase, it it converted to upper case. Variables
and routine names are converted to lower case.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: rtl8192se: Remove CamelCase variables

If a macro is in CamelCase, it it converted to upper case. Variables
and routine names are converted to lower case.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: rtl8188de: Remove CamelCase variables

If a macro is in CamelCase, it it converted to upper case. Variables
and routine names are converted to lower case.

The following checkpatch exceptions are also fixed:

CHECK: No space is necessary after a cast
#211: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192de/hw.c:109:
+                                             (u8 *) (&rfstate));

CHECK: No space is necessary after a cast
#241: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192de/hw.c:277:
+                               ptmp_byte = (u8 *) (&regtoset) + index;

Note that not all checkpatch exceptions are addressed. Those will be
handled in later patches.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: rtl8192{c,u}: Remove CamelCase variables

This patch affects modules rtl8192ce, rtl8192cu, and rtl8192com.

The following checkpatch exceptions are also fixed:

CHECK: No space is necessary after a cast
#237: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192ce/hw.c:90:
+                                                     (u8 *) (&rfstate));

CHECK: No space is necessary after a cast
#744: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192ce/rf.c:329:
+                       pwr_val[i] = (u8) ((writeval & (0x7f <<

CHECK: No space is necessary after a cast
#784: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192ce/rf.c:365:
+                                              (u8) writeval);

CHECK: spaces preferred around that '/' (ctx:VxV)
#963: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192cu/hw.c:513:
+               txqpageunit = txqpagenum/outepnum;
                                        ^

CHECK: Unnecessary parentheses around 'outepnum > 1'
#975: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192cu/hw.c:521:
+               if ((outepnum > 1) && (txqremaininpage))

CHECK: Alignment should match open parenthesis
#1059: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192cu/hw.c:617:
+static void _rtl92cu_init_chipn_two_out_ep_priority(struct ieee80211_hw *hw,
                                                                bool wmm_enable,

ERROR: "foo * bar" should be "foo *bar"
#1940: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192cu/trx.c:591:
+void rtl92cu_fill_fake_txdesc(struct ieee80211_hw *hw, u8 *pdesc,

Note that not all checkpatch exceptions are addressed. Those will be
handled in later patches.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: rtl8188ee: Remove CamelCase variable

This driver contains one instance of a CamelCase variable, namely
IS_81xxC_VENDOR_UMC_A_CUT. This macro is never used, thus it is deleted.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: btcoexist: Remove CamelCase variable

File halbt_precomp.h contains the only CamelCase value, namely
GetDefaultAdapter, but that macro is never used, thus it is deleted.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: Remove CamelCase variables from base code

There are a number of CamelCase variables remaining in the source
files of modules rtl_pci, rtl_usb, and rtlwifi.

The following checkpatch excettions are also fixed:

for_kalle1/0001-rtlwifi-Remove-CamelCase-variables-from-base-code.patch
-----------------------------------------------------------------------
CHECK: Unnecessary parentheses around 'rtlefuse->efuse_map[EFUSE_INIT_MAP][base + i] !=
                             rtlefuse->efuse_map[EFUSE_MODIFY_MAP][base + i]'
#68: FILE: drivers/net/wireless/realtek/rtlwifi/efuse.c:377:
+                       if ((rtlefuse->efuse_map[EFUSE_INIT_MAP][base + i] !=
+                            rtlefuse->efuse_map[EFUSE_MODIFY_MAP][base + i]) ||
+                           (rtlefuse->efuse_map[EFUSE_INIT_MAP][base + i + 1] !=
+                            rtlefuse->efuse_map[EFUSE_MODIFY_MAP][base + i +
                                                                   1])) {

CHECK: Unnecessary parentheses around 'rtlefuse->efuse_map[EFUSE_INIT_MAP][base + i + 1] !=
                             rtlefuse->efuse_map[EFUSE_MODIFY_MAP][base + i +
                                                                   1]'
#68: FILE: drivers/net/wireless/realtek/rtlwifi/efuse.c:377:
+                       if ((rtlefuse->efuse_map[EFUSE_INIT_MAP][base + i] !=
+                            rtlefuse->efuse_map[EFUSE_MODIFY_MAP][base + i]) ||
+                           (rtlefuse->efuse_map[EFUSE_INIT_MAP][base + i + 1] !=
+                            rtlefuse->efuse_map[EFUSE_MODIFY_MAP][base + i +
                                                                   1])) {

WARNING: line over 80 characters
#70: FILE: drivers/net/wireless/realtek/rtlwifi/efuse.c:379:
+                           (rtlefuse->efuse_map[EFUSE_INIT_MAP][base + i + 1] !=

CHECK: No space is necessary after a cast
#186: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8188ee/trx.c:396:
+       status->rx_is40mhzpacket = (bool) GET_RX_DESC_BW(pdesc);

CHECK: No space is necessary after a cast
#208: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192ce/trx.c:335:
+       stats->rx_is40mhzpacket = (bool) GET_RX_DESC_BW(pdesc);

CHECK: No space is necessary after a cast
#243: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192cu/trx.c:301:
+       stats->rx_is40mhzpacket = (bool) GET_RX_DESC_BW(pdesc);

CHECK: No space is necessary after a cast
#252: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192cu/trx.c:368:
+       stats.rx_is40mhzpacket = (bool) GET_RX_DESC_BW(rxdesc);

CHECK: No space is necessary after a cast
#265: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192de/trx.c:475:
+       stats->rx_is40mhzpacket = (bool) GET_RX_DESC_BW(pdesc);

WARNING: Unnecessary space before function pointer arguments
#455: FILE: drivers/net/wireless/realtek/rtlwifi/wifi.h:1462:
+       void (*writen_sync) (struct rtl_priv *rtlpriv, u32 addr, void *buf,

WARNING: Unnecessary space before function pointer arguments
#483: FILE: drivers/net/wireless/realtek/rtlwifi/wifi.h:2257:
+       void (*fill_fake_txdesc) (struct ieee80211_hw *hw, u8 *pdesc,

Note that not all checkpatch exceptions are addressed. Those will be
handled in later patches.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: rtl8821ae: Replace old-style license information

The traditional license information is replaced by the SPDX form. There
are no code changes.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: rtl8723_common: Replace old-style license information

The traditional license information is replaced by the SPDX form. There
are no code changes.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: rtl8723be: Replace old-style license information

The traditional license information is replaced by the SPDX form. There
are no code changes.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: rtl8723ae: Replace old-style license information

The traditional license information is replaced by the SPDX form. There
are no code changes.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: rtl8192se: Replace old-style license information

The traditional license information is replaced by the SPDX form. There
are no code changes.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: rtl8192ee: Replace old-style license information

The traditional license information is replaced by the SPDX form. There
are no code changes.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: rtl8192de: Replace old-style license information

The traditional license information is replaced by the SPDX form. There
are no code changes.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: rtl8192cu: Replace old-style license information

The traditional license information is replaced by the SPDX form. There
are no code changes.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: rtl8192ce: Replace old-style license information

The traditional license information is replaced by the SPDX form. There
are no code changes.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: rtl8192com: Replace old-style license information

The traditional license information is replaced by the SPDX form. There
are no code changes.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: rtl8188ee: Replace old-style license information

The traditional license information is replaced by the SPDX form. There
are no code changes.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: btcoex: Replace old-style license information

The old-style license information is replaced by the SPDX form. There
are no code changes.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: Replace old-style license information

The traditional license information is replaced by the SPDX form. There
are no code changes.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Merge tag 'mt76-for-kvalo-2019-02-18' of https://github.com/nbd168/wireless

mt76 patches for 5.1

* beacon support for USB devices (mesh+ad-hoc only)
* mt76x0 tx power fixes
* fixes for encryption, calibration and ED/CCA
* more code unification
* USB fixes
* fix for using the correct hweight8 function

mt76: mt76x2: simplify per-chain signal strength handling

There is no need to use a for loop here, supported chips can only support
up to 2 chains.

Signed-off-by: Felix Fietkau <nbd@nbd.name>

mt76: fix resetting software IV flag on key delete

It needs to be unset instead of set

Fixes: 23405236460b9 ("mt76: fix transmission of encrypted management frames")
Signed-off-by: Felix Fietkau <nbd@nbd.name>

mt76: fix corrupted software generated tx CCMP PN

Since ccmp_pn is u8 *, the second half needs to start at array index 4
instead of 0. Fixes a connection stall after a certain amount of traffic

Fixes: 23405236460b9 ("mt76: fix transmission of encrypted management frames")
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>

mt76: fix tx status timeout processing

Remove bogus check for MT_PACKET_ID_NO_ACK in mt76_tx_status_skb_get, which
is already handled in callers and turns timeout calls into no-ops
Do not clean up pending status items on reordering of tx status information
if the timeout is not reached yet

Signed-off-by: Felix Fietkau <nbd@nbd.name>

mt76: Use the correct hweight8() function

mt76_init_stream_cap() and mt76_get_txpower() call __sw_hweight8()
directly, but that's only defined if CONFIG_GENERIC_HWEIGHT is
enabled.  The function that works on all architectures is hweight8().

Fixes: 551e1ef4d291 ("mt76: add mt76_init_stream_cap routine")
Fixes: 9313faacbb4e ("mt76: move mt76x02_get_txpower to mt76 core")
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

mt76x02u: remove bogus check and comment padding

In mt76x02u_skb_dma_info() pad is always non-zero. Patch removes
bogus check and add comments to the function.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

mt76: usb: use dev_err_ratelimited instead of dev_err in mt76u_complete_rx

During device removal the driver can report multiple error messages.
Use dev_err_ratelimited instead of dev_err to display urb errors

Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

mt76: usb: introduce disable_usb_sg parameter

Add disable_usb_sg module parameter to disable scatter-gather on demand

Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

mt76: usb: use a linear buffer for tx/rx datapath if sg is not supported

Use linear fragment and not a single usb scatter-gather buffer in mt76u
{tx,rx} datapath if the usb controller has sg data length constraints

Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

mt76: usb: do not use sg buffers for mcu messages

Do not use scatter-gather buffers for mcu commands.
Introduce mt76u_buf_alloc and mt76u_buf_alloc_sg routines.

Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

mt76: usb: move mt76u_check_sg in usb.c

Move mt76u_check_sg routine in usb.c and introduce sg_en variable
in mt76_usb in order to check if scatter-gather is supported by
mt76u layer

Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

mt76: usb: do not run mt76u_queues_deinit twice

Do not call mt76u_queues_deinit routine in mt76u_alloc_queues error path
since it will be run in mt76x0u_register_device or
mt76x2u_register_device error path. Current implementation triggers the
following kernel warning:

[   67.005516] WARNING: CPU: 2 PID: 761 at lib/refcount.c:187 refcount_sub_and_test_checked+0xa4/0xb8
[   67.019513] refcount_t: underflow; use-after-free.
[   67.099872] Hardware name: BCM2835
[   67.106268] Backtrace:
[   67.111584] [<8010c91c>] (dump_backtrace) from [<8010cc00>] (show_stack+0x20/0x24)
[   67.124974]  r6:60000013 r5:ffffffff r4:00000000 r3:a50bade6
[   67.132226] [<8010cbe0>] (show_stack) from [<807ca5f4>] (dump_stack+0xc8/0x114)
[   67.141225] [<807ca52c>] (dump_stack) from [<8011e65c>] (__warn+0xf4/0x120)
[   67.149849]  r9:000000bb r8:804d0138 r7:00000009 r6:8099dc84 r5:00000000 r4:b66c7b58
[   67.160767] [<8011e568>] (__warn) from [<8011e6d0>] (warn_slowpath_fmt+0x48/0x50)
[   67.171436]  r9:7f65e128 r8:80d1419c r7:80c0bac4 r6:b97b3044 r5:b7368e00 r4:00000000
[   67.182433] [<8011e68c>] (warn_slowpath_fmt) from [<804d0138>] (refcount_sub_and_test_checked+0xa4/0xb8)
[   67.195221]  r3:80c91c25 r2:8099dc94
[   67.200370]  r4:00000000
[   67.204397] [<804d0094>] (refcount_sub_and_test_checked) from [<804d0164>] (refcount_dec_and_test_checked+0x18/0x1c)
[   67.218046]  r4:b7368e00 r3:00000001
[   67.223125] [<804d014c>] (refcount_dec_and_test_checked) from [<805db49c>] (usb_free_urb+0x20/0x4c)
[   67.235358] [<805db47c>] (usb_free_urb) from [<7f639804>] (mt76u_buf_free+0x98/0xac [mt76_usb])
[   67.247302]  r4:00000001 r3:00000001
[   67.252468] [<7f63976c>] (mt76u_buf_free [mt76_usb]) from [<7f639ef8>] (mt76u_queues_deinit+0x44/0x100 [mt76_usb])
[   67.266102]  r8:b8fe8600 r7:b5dac480 r6:b5dace20 r5:00000001 r4:00000000 r3:00000080
[   67.277132] [<7f639eb4>] (mt76u_queues_deinit [mt76_usb]) from [<7f65c040>] (mt76x0u_cleanup+0x40/0x4c [mt76x0u])
[   67.290737]  r7:b5dac480 r6:b8fe8600 r5:ffffffea r4:b5dace20
[   67.298069] [<7f65c000>] (mt76x0u_cleanup [mt76x0u]) from [<7f65c564>] (mt76x0u_probe+0x1f0/0x354 [mt76x0u])
[   67.311174]  r4:b5dace20 r3:00000000
[   67.316312] [<7f65c374>] (mt76x0u_probe [mt76x0u]) from [<805e0b6c>] (usb_probe_interface+0x104/0x240)
[   67.328915]  r7:00000000 r6:7f65e034 r5:b6634800 r4:b8fe8620
[   67.336276] [<805e0a68>] (usb_probe_interface) from [<8056a8bc>] (really_probe+0x224/0x2f8)
[   67.347965]  r10:b65f0a00 r9:00000019 r8:7f65e034 r7:80d3e124 r6:00000000 r5:80d3e120
[   67.359175]  r4:b8fe8620 r3:805e0a68
[   67.364384] [<8056a698>] (really_probe) from [<8056ab60>] (driver_probe_device+0x6c/0x180)
[   67.375974]  r10:b65f0a00 r9:7f65e2c0 r8:b8fe8620 r7:00000000 r6:7f65e034 r5:7f65e034
[   67.387170]  r4:b8fe8620 r3:00000000
[   67.392378] [<8056aaf4>] (driver_probe_device) from [<8056ad54>] (__driver_attach+0xe0/0xe4)
[   67.404097]  r9:7f65e2c0 r8:7f65d22c r7:00000000 r6:b8fe8654 r5:7f65e034 r4:b8fe8620
[   67.415122] [<8056ac74>] (__driver_attach) from [<8056880c>] (bus_for_each_dev+0x68/0xa0)
[   67.426628]  r6:8056ac74 r5:7f65e034 r4:00000000 r3:00000027
[   67.434017] [<805687a4>] (bus_for_each_dev) from [<8056a1cc>] (driver_attach+0x28/0x30)
[   67.445394]  r6:80c6ddc8 r5:b7368f80 r4:7f65e034
[   67.451703] [<8056a1a4>] (driver_attach) from [<80569c24>] (bus_add_driver+0x194/0x21c)
[   67.463081] [<80569a90>] (bus_add_driver) from [<8056b504>] (driver_register+0x8c/0x124)
[   67.474560]  r7:80c6ddc8 r6:7f65e034 r5:00000000 r4:7f65e034
[   67.481964] [<8056b478>] (driver_register) from [<805df510>] (usb_register_driver+0x74/0x140)
[   67.493901]  r5:00000000 r4:7f65e000
[   67.499131] [<805df49c>] (usb_register_driver) from [<7f661024>] (mt76x0_driver_init+0x24/0x1000 [mt76x0u])
[   67.512258]  r9:00000001 r8:7f65e308 r7:00000000 r6:80c08d48 r5:7f661000 r4:7f65e2c0
[   67.523404] [<7f661000>] (mt76x0_driver_init [mt76x0u]) from [<80102f6c>] (do_one_initcall+0x4c/0x210)
[   67.536142] [<80102f20>] (do_one_initcall) from [<801ae63c>] (do_init_module+0x6c/0x21c)
[   67.547639]  r8:7f65e308 r7:80c08d48 r6:b65f0ac0 r5:7f65e2c0 r4:7f65e2c0
[   67.556129] [<801ae5d0>] (do_init_module) from [<801ad68c>] (load_module+0x1d10/0x2304)

Fixes: b40b15e1521f ("mt76: add usb support to mt76 layer")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

mt76: usb: fix possible memory leak in mt76u_buf_free

Move q->ndesc initialization before the for loop in mt76u_alloc_rx
since otherwise allocated urbs will not be freed in mt76u_buf_free
Double-check scatterlist pointer in mt76u_buf_free

Fixes: b40b15e1521f ("mt76: add usb support to mt76 layer")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

mt76: usb: fix possible NULL pointer dereference in mt76u_mcu_deinit

Fix possible NULL pointer dereference in mt76u_mcu_deinit routine that
can occur if initialization path fails before calling mt76u_mcu_init_rx

Fixes: ee676cd5017c ("mt76: add driver code for MT76x2u based devices")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

mt76x02u: use usb_bulk_msg to upload firmware

We don't need to send firmware data asynchronously, much simpler is just
use synchronous usb_bulk_msg().

Tested-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

mt76x0: init: introduce mt76x0_init_txpower routine

Add mt76x0_init_txpower in order to initialize max_power per channel
at device bootstrap. Modify mt76x0_get_tx_power_per_rate and
mt76x0_get_power_info signature in order to compute tx power for
non-operating channels

Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

mt76x0: phy: report target_power in debugfs

Initialize target_power variable in mt76x0_phy_set_txpower in order to
report target_power in debugfs

Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

mt76: change the return type of mt76_dma_attach()

There is no need to retun 0 in mt76_dma_attach(), so switch it to void.

Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

mt76x2: remove mt76x2_alloc_device routine

Remove mt76x2_alloc_device since it just runs mt76_alloc_device.
Move mt76_alloc_device call in mt76x2_probe

Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

mt76x0: remove mt76x0u_alloc_device routine

Remove mt76x0u_alloc_device since it just runs mt76_alloc_device.
Move mt76_alloc_device call in mt76x0u_probe and in mt76x0e_probe

Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

mt76x2u: remove mt76x2u_alloc_device routine

Remove mt76x2u_alloc_device since it just runs mt76_alloc_device.
Move mt76_alloc_device call in mt76x2u_probe

Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

mt76: move alloc_device common code in mt76_alloc_device

Move mt76x{0,2} alloc_device common code in mt76_alloc_device and
remove duplicated code

Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

mt76: increase ED/CCA tx block threshold

Block only when the busy time reaches 92%, as lower values can be reached with
heavy 802.11 traffic as well.

Signed-off-by: Felix Fietkau <nbd@nbd.name>

mt76: measure the time between mt76x02_edcca_check runs

Based on system load and time needed by other calibration runs, the time
between dev->mac_work runs can vary quite a bit.
Calculate busy time based on the actual time difference in order to avoid
potentially over-estimating busy time, which could lead to unnecessary tx
blocking.

Signed-off-by: Felix Fietkau <nbd@nbd.name>

mt76: clear CCA timer stats in mt76x02_edcca_init

Avoid triggering too early

Signed-off-by: Felix Fietkau <nbd@nbd.name>

mt76: run MAC work every 100ms

ED/CCA Tx blocking checks need to be run every 100 ms in order to avoid
triggering too late and keeping tx blocking on for too long

Signed-off-by: Felix Fietkau <nbd@nbd.name>

mt76: explicitly disable energy detect cca during scan

Avoid reusing the previous channel's tx blocking state

Signed-off-by: Felix Fietkau <nbd@nbd.name>

mt76: mt76x2: avoid running DPD calibration if tx is blocked

Doing so could lead to hangs

Signed-off-by: Felix Fietkau <nbd@nbd.name>

mt76: fix software encryption issues

Software encrypted packets can be passed not just through the drv_tx callback,
but also through the intermediate tx queue.
In order to deal with that, move the override to mt76x02_mac_write_txwi and
also take care of filling in the per-packet rate information

Signed-off-by: Felix Fietkau <nbd@nbd.name>

mt76: remove add_buf pointer in mt76_queue_ops

Remove add_buf function pointer in mt76_queue_ops data structure since
it is no longer used

Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

mt76: move mt76_dma_tx_queue_skb_raw in mt76-core module

Move mt76_dma_tx_queue_skb_raw routine in dma.c and add the
corresponding entry in mt76_queue_ops data structure.
mt76_dma_tx_queue_skb_raw  will be reused adding support for
mt7603 driver

Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

mt76x0: mcu: remove useless commented configuration

Remove useless commented out configuration in mt76x0u_load_firmware
routine

Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

mt76: move mt76_mcu_rx_event in mt76-core

Move mt76_mcu_rx_event i mt76-core module and remove duplicated code.
mt76_mcu_rx_event will be reused adding support for mt7603 driver

Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

mt76: move mt76_mcu_get_response in mt76-core

Move mt76_mcu_get_response in mt76-core module and remove duplicated
code. mt76_mcu_get_response will be reused adding support for mt7603
driver

Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

mt76: move mt76_mcu_msg_alloc in mt76-core

Move mt76_mcu_msg_alloc in mt76-core module and remove duplicated code.
mt76_mcu_msg_alloc will be reused adding support for mt7603 driver

Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

mt76x0: eeprom: fix VHT mcs{8,9} rate power offset

Fix rate power configuration for VHT mcs 8 and 9 in
mt76x0_get_tx_power_per_rate. Moreover use the rate power
offset used for HT/VHT mcs 6 even for HT/VHT mcs 7

Fixes: b37bbc8c8251 ("mt76x0: remove eeprom dependency from mt76x0_set_tx_power_per_rate")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

mt76x02: enable support for IBSS and MESH

Since we implement beconing on USB now, similar interfaces should be
supported for USB as are for MMIO. Tested only on IBSS mode and
AP mode (not enabled due to lack of PS buffering).

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

mt76: beaconing fixes for USB

Configure beaconing on USB devices without PS buffering support.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

mt76x02: init beacon config for mt76x2u

Initialize beaconing also on mt76x2u.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

mt76x02: minor beaconing init changes

Disable BEACON timer during init and configure interrupt registers
only for mmio devices.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

mt76x02: initialize mutli bss mode when set up address

BSSID is not strtirct related with beaconing (for example we can have
2 STA vifs) and more related with MAC address, so initaize BSSID when
setting MAC address.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

mt76x02: use commmon add interface for mt76x2u

Since we now support mt76x2u feature to allow set mac address
when creating interface in common code we can use it for
mt76x2u.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

mt76x02: use mask for vifs

Use vif_mask to count interfaces to allow to set mac address in HW
if there is only one interface and report error if we create
interface with wrong BSSID resulting in already used index.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Merge tag 'iwlwifi-next-for-kalle-2019-02-14' of git://git./linux/kernel/git/iwlwifi/iwlwifi-next

Fourth batch of iwlwifi patches intended for v5.1

* Work on the new debugging infrastructure continues;
* FTM (Fine Timing Measurement) initiator and responder implementation;
* Support for a new device family started;
* Bump supported FW API to 46;
* General bugfixes;
* Other cleanups;

iwlwifi: mvm: stop static queues correctly

AP interfaces still use some static TX queues (for probes,
broadcast and multicast frames). These queues were not stopped
correctly when the transport layer indicated the queue should be
stopped. As a result, when flushing the queues, new frames from
the overflow queue were tx'd, so the queues still had frames after
flushing. This ended up in an assert since trying to remove a station
with non-empty queues.

Fix it by stopping the static queues correctly when required.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

iwlwifi: dbg_ini: add early and after alive apply points to unified images

Add IWL_FW_INI_APPLY_EARLY and IWL_FW_INI_APPLY_AFTER_ALIVE apply points
to unified images.

Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

iwlwifi: mvm: Do not return an error value on HW restart

When HW restart is requested but not started yet, commands would not
be sent to the FW, and some function calls would return an error. In
case of iwl_mvm_mac_sta_state() returning an error value when a
station is removed can lead to an unneeded warning in
__sta_info_destroy_part2().

Handle this by setting the return value to 0, in case HW restart is
in progress.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

iwlwifi: mvm: Don't warn on command failure during restart

When HW restart is requested but not started yet, commands would not
be sent to the FW, and some function calls return an error. Such cases
can trigger unneeded warning messages, e.g., in iwl_mvm_mac_sta_state()
and iwl_mvm_bss_info_changed_station().

Handle a couple of these cases by also checking in the WARN_ON()
condition that HW restart is not requested.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

iwlwifi: dbg: buffer overflow in non_collect_ts_start array

The size of the buffer is IWL_FW_TRIGGER_ID_NUM - 1 which is equal to
IWL_FW_TRIGGER_ID_HOST_CHANNEL_SWITCH_COMPLETE so if the driver receives
this trigger, it will cause a buffer overflow.

Solve this by increasing the buffer size by 1.

Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Fixes: fe1b7d6c2888 ("iwlwifi: add support for triggering ini triggers")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>