Mieczyslaw Nalewaj [Sun, 28 Jul 2024 12:49:44 +0000 (14:49 +0200)]
archs38: use kernel 6.6 by default
Switch to Linux kernel version 6.6.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16021
Signed-off-by: Robert Marko <robimarko@gmail.com>
INAGAKI Hiroshi [Wed, 24 Apr 2024 16:08:41 +0000 (01:08 +0900)]
ath79: add support for NEC Aterm WG600HP
NEC Aterm WG600HP is a 2.4/5 GHz band 11n (Wi-Fi 4) router, based on
AR9344.
Specification:
- SoC : Atheros AR9344
- RAM : DDR2 128 MiB (2x Hynix H5PS5162GFR-S6C)
- Flash : SPI-NOR 8 MiB (Macronix MX25L6406EMI-12G)
- WLAN : 2.4/5 GHz 2T2R
- 2.4 GHz : Atheros AR9344 (SoC)
- 5 GHz : Atheros AR9382
- Ethernet : 5x 10/100/1000 Mbps
- switch : Atheros AR8327
- LEDs/Keys (GPIO): 10x/4x
- note : all LEDs are controlled by ath9k chip (AR9382)
- UART : through-hole on PCB
- assignment : 3.3V, GND, NC, TX, RX from tri-angle marking
- settings : 9600n8
- USB : 1x USB 2.0 Type-A
- hub (internal): NEC uPD720114
- Power : 12 VDC, 1.5 A (Max. 16 W)
- Stock OS : NetBSD based
Flash instruction using initramfs-factory.bin image (StockFW WebUI):
1. Boot WG600HP with router mode normally
2. Access to the WebUI ("http://aterm.me/" or "http://192.168.0.1/") on
the device and open firmware update page ("ファームウェア更新")
3. Select the OpenWrt initramfs-factory.bin image and click update
("更新") button
4. After updating, the device will be rebooted and booted with OpenWrt
initramfs image
5. On the initramfs image, upload (or download) uboot.bin and
sysupgrade.bin image to the device
6. Replace the bootloader with a uboot.bin image
mtd write <uboot.bin image> bootloader
7. Perform sysupgrade with a sysupgrade.bin image
sysupgrade <sysupgrade image>
8. Wait ~120 seconds to complete flashing
Flash instruction using initramfs-factory.bin image (bootloader CLI):
1. Connect and open serial console
2. Power on WG600HP and interrupt bootloader by ESC key
3. Login to the bootloader CLI with a password "chiron"
4. Start TFTP server by "tftpd" command
5. Upload initramfs-factory.bin via tftp from your computer
example (Windows): tftp -i 192.168.0.1 PUT initramfs-factory.bin
6. Boot initramfs image by "boot" command
7. On the initramfs image, back up the stock bootloader and firmware if
needed
8. Upload (or download) uboot.bin and sysupgrade.bin image to the device
9. Replace the bootloader with a uboot.bin image
10. Perform sysupgrade with a sysupgrade.bin image
11. Wait ~120 seconds to complete flashing
Notes:
- All LEDs are connected to the GPIO controller on the ath9k chip
(AR9382) and controlled by it. Those LEDs are probed after probing of
ath9k chip, so they cannot be handled as status LEDs of OpenWrt while
booting.
- A reset pin of the internal USB hub is connected to the GPIO
controller of the ath9k chip, like LEDs above. That hub will be
detected after probing of the ath9k chip.
- The stock bootloader requires an unknown filesystem on firmware area
in the flash. Booting of OpenWrt from that filesystem cannot be
handled, so the bootloader needs to be replaced to mainline U-Boot
before OpenWrt installation.
MAC Addresses:
LAN : A4:12:42:xx:xx:A0 (config, 0x6 (hex))
WAN : A4:12:42:xx:xx:A1 (config, 0xc (hex))
2.4 GHz: A4:12:42:xx:xx:A2 (config, 0x0 (hex) / art, 0x1002 (hex))
5 GHz : A4:12:42:xx:xx:A3 (config, 0x12 (hex) / art, 0x5002 (hex))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15432
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
INAGAKI Hiroshi [Wed, 24 Apr 2024 16:08:41 +0000 (01:08 +0900)]
ath79: add support for NEC Aterm WR9500N
NEC Aterm WR9500N is a 2.4/5 GHz band 11n (Wi-Fi 4) router, based on
AR9344.
Specification:
- SoC : Atheros AR9344
- RAM : DDR2 128 MiB (2x Nanya NT5TU32M16DG-AC)
- Flash : SPI-NOR 16 MiB (Macronix MX25L12845EMI-10G)
- WLAN : 2.4/5 GHz
- 2.4 GHz : 2T2R, Atheros AR9344 (SoC)
- 5 GHz : 3T3R, Atheros AR9380
- Ethernet : 5x 10/100/1000 Mbps
- switch : Atheros AR8327
- LEDs/Keys (GPIO): 12x/4x
- note : all LEDs are controlled by ath9k chip (AR9380)
- UART : pad on PCB (near shielded ath9k chip, white circle)
- assignment : 3.3V, GND, TX, RX from AR8327 side
- settings : 9600n8
- USB : 1x USB 2.0 Type-A
- hub (internal): NEC uPD720114
- Power : 12 VDC, 1.5 A (Max. 17 W)
- Stock OS : NetBSD based
Flash instruction using initramfs-factory.bin image (StockFW WebUI):
1. Boot WR9500N with router mode normally
2. Access to the WebUI ("http://aterm.me/" or "http://192.168.0.1/") on
the device and open firmware update page ("ファームウェア更新")
3. Select the OpenWrt initramfs-factory.bin image and click update
("更新") button
4. After updating, the device will be rebooted and booted with OpenWrt
initramfs image
5. On the initramfs image, upload (or download) uboot.bin and
sysupgrade.bin image to the device
6. Replace the bootloader with a uboot.bin image
mtd write <uboot.bin image> bootloader
7. Perform sysupgrade with a sysupgrade.bin image
sysupgrade <sysupgrade image>
8. Wait ~120 seconds to complete flashing
Flash instruction using initramfs-factory.bin image (bootloader CLI):
1. Connect and open serial console
2. Power on WR9500N and interrupt bootloader by ESC key
3. Login to the bootloader CLI with a password "chiron"
4. Start TFTP server by "tftpd" command
5. Upload initramfs-factory.bin via tftp from your computer
example (Windows): tftp -i 192.168.0.1 PUT initramfs-factory.bin
6. Boot initramfs image by "boot" command
7. On the initramfs image, back up the stock bootloader and firmware if
needed
8. Upload (or download) uboot.bin and sysupgrade.bin image to the device
9. Replace the bootloader with a uboot.bin image
10. Perform sysupgrade with a sysupgrade.bin image
11. Wait ~120 seconds to complete flashing
Notes:
- All LEDs are connected to the GPIO controller on the ath9k chip
(AR9380) and controlled by it. Those LEDs are probed after probing of
ath9k chip, so they cannot be handled as status LEDs of OpenWrt while
booting.
- A reset pin of the internal USB hub is connected to the GPIO
controller of the ath9k chip, like LEDs above. That hub will be
detected after probing of the ath9k chip.
- The stock bootloader requires an unknown filesystem on firmware area
in the flash. Booting of OpenWrt from that filesystem cannot be
handled, so the bootloader needs to be replaced to mainline U-Boot
before OpenWrt installation.
MAC Addresses:
LAN : 1C:B1:7F:xx:xx:60 (config, 0x6 (hex))
WAN : 1C:B1:7F:xx:xx:61 (config, 0xc (hex))
2.4 GHz: 1C:B1:7F:xx:xx:62 (config, 0x0 (hex) / art, 0x1002 (hex))
5 GHz : 1C:B1:7F:xx:xx:63 (config, 0x12 (hex) / art, 0x5002 (hex))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15432
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
INAGAKI Hiroshi [Wed, 24 Apr 2024 16:08:41 +0000 (01:08 +0900)]
ath79: add support for NEC Aterm WR8750N
NEC Aterm WR8750N is a 2.4/5 GHz band 11n (Wi-Fi 4) router, based on
AR9344.
Specification:
- SoC : Atheros AR9344
- RAM : DDR2 128 MiB (2x Hynix H5PS5162GFR-S6C)
- Flash : SPI-NOR 8 MiB (Macronix MX25L6406EMI-12G)
- WLAN : 2.4/5 GHz 2T2R
- 2.4 GHz : Atheros AR9344 (SoC)
- 5 GHz : Atheros AR9382
- Ethernet : 5x 10/100/1000 Mbps
- switch : Atheros AR8327
- LEDs/Keys (GPIO): 10x/4x
- note : all LEDs are controlled by ath9k chip (AR9382)
- UART : through-hole on PCB
- assignment : 3.3V, GND, NC, TX, RX from tri-angle marking
- settings : 9600n8
- USB : 1x USB 2.0 Type-A
- hub (internal): NEC uPD720114
- Power : 12 VDC, 1.5 A (Max. 16 W)
- Stock OS : NetBSD based
Flash instruction using initramfs-factory.bin image (StockFW WebUI):
1. Boot WR8750N with router mode normally
2. Access to the WebUI ("http://aterm.me/" or "http://192.168.0.1/") on
the device and open firmware update page ("ファームウェア更新")
3. Select the OpenWrt initramfs-factory.bin image and click update
("更新") button
4. After updating, the device will be rebooted and booted with OpenWrt
initramfs image
5. On the initramfs image, upload (or download) uboot.bin and
sysupgrade.bin image to the device
6. Replace the bootloader with a uboot.bin image
mtd write <uboot.bin image> bootloader
7. Perform sysupgrade with a sysupgrade.bin image
sysupgrade <sysupgrade image>
8. Wait ~120 seconds to complete flashing
Flash instruction using initramfs-factory.bin image (bootloader CLI):
1. Connect and open serial console
2. Power on WR8750N and interrupt bootloader by ESC key
3. Login to the bootloader CLI with a password "chiron"
4. Start TFTP server by "tftpd" command
5. Upload initramfs-factory.bin via tftp from your computer
example (Windows): tftp -i 192.168.0.1 PUT initramfs-factory.bin
6. Boot initramfs image by "boot" command
7. On the initramfs image, back up the stock bootloader and firmware if
needed
8. Upload (or download) uboot.bin and sysupgrade.bin image to the device
9. Replace the bootloader with a uboot.bin image
10. Perform sysupgrade with a sysupgrade.bin image
11. Wait ~120 seconds to complete flashing
Notes:
- All LEDs are connected to the GPIO controller on the ath9k chip
(AR9382) and controlled by it. Those LEDs are probed after probing of
ath9k chip, so they cannot be handled as status LEDs of OpenWrt while
booting.
- A reset pin of the internal USB hub is connected to the GPIO
controller of the ath9k chip, like LEDs above. That hub will be
detected after probing of the ath9k chip.
- The stock bootloader requires an unknown filesystem on firmware area
in the flash. Booting of OpenWrt from that filesystem cannot be
handled, so the bootloader needs to be replaced to mainline U-Boot
before OpenWrt installation.
MAC Addresses:
LAN : 1C:B1:7F:xx:xx:00 (config, 0x6 (hex))
WAN : 1C:B1:7F:xx:xx:01 (config, 0xc (hex))
2.4 GHz: 1C:B1:7F:xx:xx:02 (config, 0x0 (hex) / art, 0x1002 (hex))
5 GHz : 1C:B1:7F:xx:xx:03 (config, 0x12 (hex) / art, 0x5002 (hex))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15432
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
INAGAKI Hiroshi [Fri, 26 Apr 2024 14:54:57 +0000 (23:54 +0900)]
ath79: add missing reset de-assertion of PCIe endpoint
Fix PCIe initialization by de-assertion of PCIe endpoint reset.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15432
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
INAGAKI Hiroshi [Fri, 26 Apr 2024 14:53:58 +0000 (23:53 +0900)]
ath79: fix PCIe initialization on AR934x
Fix PCIe initialization on AR934x by clearing PLL_PWD bit in addition to
PPL(PLL?)_RESET bit of AR724x.
Refresh patches by `make target/linux/refresh`.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15432
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
INAGAKI Hiroshi [Fri, 26 Apr 2024 14:34:31 +0000 (23:34 +0900)]
uboot-ath79: add support for NEC Aterm series based on AR9344
Add support for NEC Aterm series devices based on Atheros AR9344.
The following devices have almost the same hardware, so the same U-Boot
binary can be used for them.
- NEC Aterm WR8750N
- NEC Aterm WR9500N
- NEC Aterm WG600HP
By the way, on NetBSD-based NEC Aterm devices, only 0x20000 (128KiB) is
available for a bootloader on the flash chip and that limitation is too
small for mainline U-Boot with the default options. So many
features/commands not required for booting OpenWrt and recoverying are
disabled on that devices, like the followings.
- networking support
- FIT support
- all decompression methods support
etc...
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15432
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
INAGAKI Hiroshi [Fri, 26 Apr 2024 14:33:24 +0000 (23:33 +0900)]
uboot-ath79: add new U-Boot package for Atheros/QCA devices
Add U-Boot package for the devices that based on Atheros/Qualcomm
Atheros SoCs.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15432
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Thu, 25 Jul 2024 20:13:35 +0000 (22:13 +0200)]
ipq40xx: eth: Fix PHY access over ipqess driver
.ndo_do_ioctl is not called any more. For PHY MII ioctl handling, the
kernel calls .ndo_eth_ioctl now.
See upstream Linux kernel commit:
https://git.kernel.org/linus/
a76053707dbf0dc020a73b4d90cd952409ef3691
Link: https://github.com/openwrt/openwrt/pull/16005
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Thu, 25 Jul 2024 20:09:04 +0000 (22:09 +0200)]
ramips: eth: Fix PHY access over mtk_eth_soc driver
.ndo_do_ioctl is not called any more. For PHY MII ioctl handling, the
kernel calls .ndo_eth_ioctl now.
See upstream Linux kernel commit:
https://git.kernel.org/linus/
a76053707dbf0dc020a73b4d90cd952409ef3691
Link: https://github.com/openwrt/openwrt/pull/16005
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Thu, 25 Jul 2024 20:05:11 +0000 (22:05 +0200)]
ath79: Fix PHY access over ag71xx driver
.ndo_do_ioctl is not called any more. For PHY MII ioctl handling, the
kernel calls .ndo_eth_ioctl now.
The SIOCSIFHWADDR and SIOCGIFHWADDR operation are handled in the generic
code in the same way just with more input validation.
See upstream Linux kernel commit:
https://git.kernel.org/linus/
a76053707dbf0dc020a73b4d90cd952409ef3691
Reported-by: Cthulhu88 in https://forum.openwrt.org/t/ethernet-leds-control-for-tp-link-tl-wr1043nd-v2-v3/202378
Link: https://github.com/openwrt/openwrt/pull/16005
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Thu, 25 Jul 2024 19:51:42 +0000 (21:51 +0200)]
ltq-ptm: Fix netdev ioctls with kernel > 5.15
.ndo_do_ioctl is not called for SIOCDEVPRIVATE any more, the kernel
calls .ndo_siocdevprivate now.
The function gets the data pointer from the callback directly, make use
of it.
See upstream Linux kernel commit:
https://git.kernel.org/linus/
b9067f5dc4a07c8e24e01a1b277c6722d91be39e
Link: https://github.com/openwrt/openwrt/pull/16005
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Mieczyslaw Nalewaj [Thu, 25 Jul 2024 18:54:55 +0000 (20:54 +0200)]
archs38: enable 6.6 testing kernel
The archs38 now supports 6.6 kernel as testing.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16004
Signed-off-by: Robert Marko <robimarko@gmail.com>
Mieczyslaw Nalewaj [Sat, 27 Jul 2024 21:51:16 +0000 (23:51 +0200)]
generic: 6.6: backport fix uninitialized variable warnings
Fix uninitialized variable warnings in function regcache_maple_drop
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16004
Signed-off-by: Robert Marko <robimarko@gmail.com>
Mieczyslaw Nalewaj [Thu, 25 Jul 2024 18:42:30 +0000 (20:42 +0200)]
archs38: refresh config-6.6
Refresh kernel config for Linux 6.6.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16004
Signed-off-by: Robert Marko <robimarko@gmail.com>
Mieczyslaw Nalewaj [Thu, 25 Jul 2024 16:18:49 +0000 (18:18 +0200)]
kernel/archs38: Restore kernel files for v6.1
This is an automatically generated commit which aids following Kernel patch
history, as git will see the move and copy as a rename thus defeating the
purpose.
For the original discussion see:
https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16004
Signed-off-by: Robert Marko <robimarko@gmail.com>
Mieczyslaw Nalewaj [Thu, 25 Jul 2024 16:18:39 +0000 (18:18 +0200)]
kernel/archs38: Create kernel files for v6.6 (from v6.1)
This is an automatically generated commit.
When doing `git bisect`, consider `git bisect --skip`.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16004
Signed-off-by: Robert Marko <robimarko@gmail.com>
Michael Pratt [Thu, 11 Jul 2024 10:33:55 +0000 (06:33 -0400)]
tools/7z: update to 24.05
Update to a more recent stable release.
Most notably, this version includes
some fixes for building on an OS like Alpine.
This allows for the removal of hacks
that fixed building on Alpine,
but broke building on ARM archs.
Manually adjust:
- 7-zip-flags.patch
- 7-zip-musl.patch
Link: https://7-zip.org/history.txt
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Link: https://github.com/openwrt/openwrt/pull/15991
Signed-off-by: Robert Marko <robimarko@gmail.com>
Michael Pratt [Thu, 11 Jul 2024 07:54:29 +0000 (03:54 -0400)]
tools/7z: cleanup Makefile
Define the version in one variable,
and use Make functions to use variations of it elsewhere.
Correct the CPE ID.
Override the default tar directory flag
by adding a new value to the tar options
instead of defining the entire command.
Use variables for adjusting build recipes
instead of adding custom build recipes.
Remove unnecessary lines and add spacing.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Link: https://github.com/openwrt/openwrt/pull/15991
Signed-off-by: Robert Marko <robimarko@gmail.com>
Michael Pratt [Thu, 11 Jul 2024 06:36:18 +0000 (02:36 -0400)]
build: add support for host building in a subdirectory
Add HOST_MAKE_PATH and use it in order to execute Make
in a subdirectory of the build directory
and in a similar way that MAKE_PATH is used for target building.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Link: https://github.com/openwrt/openwrt/pull/15991
Signed-off-by: Robert Marko <robimarko@gmail.com>
Thomas Weißschuh [Tue, 23 Jul 2024 19:22:17 +0000 (21:22 +0200)]
util-linux: update to v2.40.2
Release Notes:
https://mirrors.edge.kernel.org/pub/linux/utils/util-linux/v2.40/v2.40-ReleaseNotes
https://mirrors.edge.kernel.org/pub/linux/utils/util-linux/v2.40/v2.40.1-ReleaseNotes
https://mirrors.edge.kernel.org/pub/linux/utils/util-linux/v2.40/v2.40.2-ReleaseNotes
Remove upstreamed:
0001-meson-Fix-build-python-option.patch
Signed-off-by: Thomas Weißschuh <thomas@t-8ch.de>
Link: https://github.com/openwrt/openwrt/pull/15995
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Thomas Weißschuh [Tue, 23 Jul 2024 19:24:39 +0000 (21:24 +0200)]
tools: util-linux: update to v2.40.2
Also switch from .tar.gz to .tar.xz to align with
package/utils/util-linux/Makefile.
This makes synchronized updates easier.
Release Notes:
https://mirrors.edge.kernel.org/pub/linux/utils/util-linux/v2.40/v2.40-ReleaseNotes
https://mirrors.edge.kernel.org/pub/linux/utils/util-linux/v2.40/v2.40.1-ReleaseNotes
https://mirrors.edge.kernel.org/pub/linux/utils/util-linux/v2.40/v2.40.2-ReleaseNotes
Signed-off-by: Thomas Weißschuh <thomas@t-8ch.de>
Link: https://github.com/openwrt/openwrt/pull/15995
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Rafał Miłecki [Fri, 12 Jul 2024 09:36:48 +0000 (11:36 +0200)]
base-files: upgrade: nand: allow custom fw extraction in nand_do_upgrade()
By default nand_do_upgrade() can only deal with raw and gzipped firmware
files. Vendors often use custom firmware containers. Allow passing
custom extraction command to allow using nand_do_upgrade() with vendor
firmwares.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Chukun Pan [Tue, 18 Jun 2024 15:02:12 +0000 (23:02 +0800)]
mediatek: add support for TP-Link TL-XTR8488
Hardware specification:
SoC: MediaTek MT7986A 4x A53
Flash: ESMT F50L1G41LB 128MB
RAM: MT40A512M16TB-062ER 1GB
Ethernet: 2x 2.5G, 4x 1G Lan
WiFi1: MT7976GN 2.4GHz 4T4R
WiFi2: MT7976AN 5.2GHz 4T4R
WiFi3: MT7915AN 5.8GHz 4T4R
Button: Reset, WPS, Turbo
USB: 1 x USB 3.0
Power: DC 12V 5A
Flash instructions:
1. Execute the following operation to open nc shell:
https://openwrt.org/inbox/toh/tp-link/xdr-6086#rooting
2. Replace the stock bootloader to OpenWrt's:
dd bs=131072 conv=sync of=/dev/mtdblock9 if=/tmp/xxx-preloader.bin
dd bs=131072 conv=sync of=/dev/mtdblock9 seek=28 if=/tmp/xxx-bl31-uboot.fip
3. Connect to your PC via the Gigabit port of the router,
set a static ip on the ethernet interface of your PC.
4. Download the initramfs image, and restart the router,
waiting for tftp recovery to complete.
5. After openwrt boots up, perform sysupgrade.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/15930
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Chukun Pan [Mon, 17 Jun 2024 12:10:06 +0000 (20:10 +0800)]
uboot-mediatek: add TP-LINK TL-XTR8488 support
Same as TP-Link TL-XDR608x, this router comes with locked vendor
loader. Add U-Boot build for replacement loader for this device.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/15930
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
FUKAUMI Naoki [Wed, 24 Jul 2024 05:48:09 +0000 (14:48 +0900)]
rockchip: add support for Radxa ROCK 3A
Radxa ROCK 3A is a credit card sized SBC with rich interfaces[1] using
the Rockchip RK3328 SoC.
Hardware
--------
- Rockchip RK3568 SoC
- Quad Cortex-A55 CPU
- Mail G52 GPU
- 1 TOPs NPU
- 2/4/8GB LPDDR4 RAM
- 1x eMMC connector
- 1x M.2 M Key (2-lane PCIe 3.0) supporting NVMe SSD
- 1x Micro SD card slot
- 1x 1000M Ethernet with PoE support (additional PoE HAT required)
- 1x USB 3.0 Type-A port (Host)
- 1x USB 3.0 Type-A port (OTG)
- 2x USB 2.0 Type-A ports (Host)
- 40 pin color GPIO header
[1] https://radxa.com/products/rock3/3a
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/15985
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Rafał Miłecki [Thu, 18 Jul 2024 08:37:38 +0000 (10:37 +0200)]
treewide: fixup models names for UniFi U6 series
Ubiquiti has a set of UniFi 802.11ax (Wi-Fi 6) AP devices. All models
include "U6" in their names and also have code names with no special
characters (including spaces).
Examples:
1. U6 Lite (codename U6-Lite)
2. U6 Long-Range (codename U6-LR)
3. U6+ (codename U6-PLUS)
4. U6 Pro (codename U6-Pro)
5. U6 Mesh (codename U6-Mesh)
6. U6 Mesh Pro (codename U6-Mesh-Pro)
7. U6 Enterprise (codename U6-Enterprise)
Use proper full names for those devices. Names in OpenWrt/DTS code may
need updating too but it can be handled later.
Cc: Elbert Mai <code@elbertmai.com>
Cc: Daniel Golle <daniel@makrotopia.org>
Cc: Henrik Riomar <henrik.riomar@gmail.com>
Cc: David Bauer <mail@david-bauer.net>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
FUKAUMI Naoki [Sun, 21 Jul 2024 23:01:56 +0000 (08:01 +0900)]
rockchip: add support for Radxa ROCK Pi S
Radxa ROCK Pi S is a small in size, full in features SBC[1] using the
Rockchip RK3308B SoC.
Hardware
--------
- Rockchip RK3308B SoC
- Quad A35 CPU
- 256/512MB DDR3 RAM
- Optional 4/8GB eMMC
- Micro SD Card slot
- Optional WiFi 4 and BT 4 (not supported yet)
- 1x 100M Ethernet with PoE support (additional PoE HAT required)
- 1x USB 2.0 Type-A port (Host)
- 1x USB 2.0 Type-C port (OTG)
- 2x 26 Pin GPIO header
[1] https://radxa.com/products/rockpi/pis
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/15933
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
FUKAUMI Naoki [Wed, 10 Jul 2024 21:33:41 +0000 (06:33 +0900)]
wifi-scripts: add missing dependency on ucode-mod-rtnl
rtnl is used in hostap/common.uc.
$ grep -r rtnl files
files/usr/share/hostap/common.uc:import * as rtnl from "rtnl";
files/usr/share/hostap/common.uc: rtnl.request(rtnl.const.RTM_SETLINK, 0, { dev: reuse_ifname, ifname: name}) != false))
files/usr/share/hostap/common.uc: rtnl.request(rtnl.const.RTM_SETLINK, 0, { dev: name, change: 1, flags: up ? 1 : 0 });
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/15922
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Michel Promonet [Sun, 23 Jun 2024 19:46:46 +0000 (21:46 +0200)]
sunxi: add csi video support for nanopi-neo-air
add dtc configuration that declare CSI connection with ov5640
Signed-off-by: Michel Promonet <michel.promonet@free.fr>
Link: https://github.com/openwrt/openwrt/pull/15967
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Martin Schiller [Wed, 21 Aug 2019 07:04:15 +0000 (09:04 +0200)]
firmware: add Intel/Lantiq VRX518 DSL firmware package
This is required by the DSL CPE API driver.
Signed-off-by: Martin Schiller <ms.3headeddevs@gmail.com>
[update for new license]
Signed-off-by: Andre Heider <a.heider@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15550
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Martin Schiller [Wed, 21 Aug 2019 06:32:09 +0000 (08:32 +0200)]
firmware: add Intel/Lantiq VRX518 PPE firmware package
This firmware is used by the vrx518 tc driver.
Signed-off-by: Martin Schiller <ms.3headeddevs@gmail.com>
[update for new license]
Signed-off-by: Andre Heider <a.heider@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15550
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Martin Schiller [Wed, 21 Aug 2019 06:05:06 +0000 (08:05 +0200)]
firmware: add Intel/Lantiq VRX518 ACA firmware package
This firmware is used by the vrx518 ep driver.
Signed-off-by: Martin Schiller <ms.3headeddevs@gmail.com>
[update for new license]
Signed-off-by: Andre Heider <a.heider@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15550
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Maxim Anisimov [Tue, 18 Jun 2024 13:09:35 +0000 (16:09 +0300)]
ramips: add support for Keenetic KN-3510
Keenetic KN-3510 is a 2.4/5 Ghz band 11ax access point
Specification:
- System-On-Chip: MT7621AT
- CPU/Speed: 880 MHz
- Flash-Chip: Macronix MX30LF1G28AD-TI
- Flash size: 128 MiB
- RAM: 256 MiB
- 2x 10/100/1000 Mbps Ethernet
- PoE, 802.3af/at
- 4x internal antennas
- UART (J1) header on PCB (115200 8n1)
- WiFi: MT7915 2x2 2.4G 573.5Mbps + 2x2 5G 1201Mbps
- 2x LED, 2x button, 1x mode switch
Notes:
- The device supports dual boot mode
- The firmware partitions were concatinated into one
Flash instruction:
The only way to flash OpenWrt image is to use tftp recovery mode in U-Boot:
1. Configure PC with static IP 192.168.1.2/24 and tftp server.
2. Rename "openwrt-ramips-mt7621-keenetic_kn-3510-squashfs-factory.bin"
to "KN-3510_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
the router and keep button pressed until power led start blinking.
4. Router will download file from server, write it to flash and reboot
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15744
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Borys Zhukov [Sun, 7 Jul 2024 22:54:07 +0000 (18:54 -0400)]
ramips: add support for Netgear WAX214v2
Netgear WAX214v2 is an 802.11ax (Wi-Fi 6) wireless access point.
Specifications:
* SoC: MediaTek MT7621AT
* RAM: 512 MiB
* Flash: NAND 128 MiB (ESMT PSU1GA30DT)
* Wi-Fi: 2.4/5 GHz 4T4R (MediaTek MT7915E)
* Ethernet: 1x 10/100/1000 Mbps LAN
* Switch: MediaTek MT7530 (SoC built-in)
* LEDs/Keys
* Power (green, blue, amber)
* LAN (green, amber)
* WLAN 2.4GHz (green, blue)
* WLAN 5GHz (green, blue)
* Reset button
* USB: None
* UART: Marked J1 on board, 115200 8N1
* Power
* 12 VDC, 1.5 A
* IEEE 802.3at (PoE+)
Load addresses (same as Netgear WAX202):
* stock
* 0x80010000: FIT image
* 0x81001000: kernel image -> entry
* OpenWrt
* 0x80010000: FIT image
* 0x82000000: uncompressed kernel+relocate image
* 0x80001000: relocated kernel image -> entry
MAC addresses as verified by OEM firmware:
vendor OpenWrt address
eth0 lan label
ra0 phy0 label + 2
rax0 phy1 label + 3
Installation:
* Flash the factory image by TFTP to the bootloader.
NMRP can be used to TFTP without opening the case.
Revert to stock firmware:
* Flash the stock firmware to the bootloader using TFTP/NMRP.
References to WAX214v2 GPL source:
https://www.downloads.netgear.com/files/GPL/WAX214v2-V1.0.1.5-gpl-src.tar.gz
* openwrt/target/linux/ramips/dts/mt7621-ax-nand-wax214v2.dts
DTS file for this device.
Signed-off-by: Borys Zhukov <borys@zhukov.org>
Link: https://github.com/openwrt/openwrt/pull/14401
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Luiz Angelo Daros de Luca [Sat, 6 Jul 2024 07:37:42 +0000 (04:37 -0300)]
kernel: modules: video: add kmod-video-gspca-pac7302
Add the package for the Pixart PAC7302 USB Camera Driver kernel module.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15886
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Eros Brigmann [Thu, 4 Jul 2024 18:10:25 +0000 (20:10 +0200)]
ramips: add support for Wavlink WL-WN531G3-A2
This device is exactly the same as WL-WN531G3 but with different partition layout and different MAC layout. Labeled as Quantum D4G Rev.: A2.
Hardware
--------
SoC: Mediatek MT7620A
RAM: 64MB
FLASH: 8MB NOR (GigaDevice GD25Q64CS)
ETH:
- 2x 10/100/1000 Mbps Ethernet (RTL8211F)
- 3x 10/100 Mbps Ethernet (integrated in SOC)
WIFI:
- 2.4GHz: 1x (integrated in SOC) (2x2:2)
- 5GHz: 1x MT7612E (2x2:2)
- 4 external antennas
BTN:
- 1x Reset button
- 1x Touchlink button
- 1x Turbo button
- 1x Wps button
- 1x ON/OFF switch
LEDS:
- 1x Red led (system status)
- 1x Blue led (system status)
- 5x Blue leds (ethernet ports)
- 1x Power led
- 1x Wifi led
UART:
- 57600-8-N-1
Everything works correctly.
Installation
------------
Flash the initramfs image in the OEM firmware interface
When Openwrt boots, flash the sysupgrade image otherwise you won't be
able to keep configuration between reboots.
Notes
-----
1) Router mac addresses:
LAN XX:XX:XX:XX:XX:0F (factory @ 0x28)
WAN XX:XX:XX:XX:XX:10 (factory @ 0x2e)
WIFI 2G XX:XX:XX:XX:XX:11 (factory @ 0x04)
WIFI 5G XX:XX:XX:XX:XX:12 (factory @ 0x8004)
LABEL XX:XX:XX:XX:XX:11
Signed-off-by: Eros Brigmann <erosbrigmann@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15876
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
FUKAUMI Naoki [Wed, 10 Jul 2024 21:20:21 +0000 (06:20 +0900)]
rockchip: make SATA(AHCI) really work on Radxa E25
kmod-ahci-dwc is required to use SATA(AHCI) on Radxa E25.
Fixes: f7c732bf9e ("rockchip: add Radxa E25 board support")
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/15923
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Luca Piccirillo [Wed, 10 Jul 2024 16:48:39 +0000 (18:48 +0200)]
treewide: match the COMFAST brand name across supported devices
COMFAST CF-E393AX
COMFAST CF-E390AX & CF-EW72 V2
COMFAST CF-WR617AC
Signed-off-by: Luca Piccirillo <luca.piccirillo@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14690
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Kristian Skramstad [Fri, 12 Jul 2024 06:47:23 +0000 (08:47 +0200)]
ath79: qca9563: Amplifi Router HD: add DEVICE_VENDOR Ubiquiti
In make menuconfig the name is [Amplifi Router HD], and
is missing Ubiquiti. Lets fix that by adding
DEVICE_VENDOR := Ubiquiti to generic-ubnt.mk so the name is:
[Ubiquiti Amplifi Router HD].
Signed-off-by: Kristian Skramstad <kristian+github@83.no>
Link: https://github.com/openwrt/openwrt/pull/15932
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Philip Prindeville [Sun, 14 Jul 2024 20:07:53 +0000 (14:07 -0600)]
base-files: ipcalc.sh handle start and range being empty strings
If we're being paranoid and quote all the arguments to ipcalc.sh,
it's possible to pass in empty start and range arguments. This
should be handled the same as their being absent.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Link: https://github.com/openwrt/openwrt/pull/15946
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Marco von Rosenberg [Sun, 31 Mar 2024 15:07:13 +0000 (17:07 +0200)]
ath79: add support for Huawei AP6010DN
Huawei AP6010DN is a dual-band, dual-radio 802.11a/b/g/n 2x2 MIMO
enterprise access point with one Gigabit Ethernet port and PoE
support.
Hardware highlights:
- CPU: AR9344 SoC at 480MHz
- RAM: 128MB DDR2
- Flash: 32MB SPI-NOR
- Wi-Fi 2.4GHz: AR9344-internal radio
- Wi-Fi 5GHz: AR9580 PCIe WLAN SoC
- Ethernet: 10/100/1000 Mbps Ethernet through Atheros AR8035 PHY
- PoE: yes
- Standalone 12V/2A power input
- Serial console externally available through RJ45 port
- External watchdog: CAT706SVI (1.6s timeout)
Serial console:
9600n8 (9600 baud, no stop bits, no parity, 8 data bits)
MAC addresses:
Each device has 32 consecutive MAC addresses allocated by
the vendor, which don't overlap between devices.
This was confirmed with multiple devices with consecutive
serial numbers.
The MAC address range starts with the address on the label.
To be able to distinguish between the interfaces,
the following MAC address scheme is used:
- eth0 = label MAC
- radio0 (Wi-Fi 2.4GHz) = label MAC + 1
- radio1 (Wi-Fi 5GHz) = label MAC + 2
Installation:
0. Connect some sort of RJ45-to-USB adapter to "Console" port of the AP
1. Power up the AP
2. At prompt "Press f or F to stop Auto-Boot in 3 seconds",
do what they say.
Log in with default admin password "admin@huawei.com".
3. Boot the OpenWrt initramfs from TFTP using the hidden script "run ramboot".
Replace IP address as needed:
> setenv serverip 192.168.1.10
> setenv ipaddr 192.168.1.1
> setenv rambootfile openwrt-ath79-generic-huawei_ap6010dn-initramfs-kernel.bin
> saveenv
> run ramboot
4. Optional but recommended as the factory firmware cannot be downloaded publicly:
Back up contents of "firmware" partition using the web interface or ssh:
$ ssh root@192.168.1.1 cat /dev/mtd11 > huawei_ap6010dn_fw_backup.bin
5. Run sysupgrade using sysupgrade image. OpenWrt
shall boot from flash afterwards.
Return to factory firmware (using firmware upgrade package downloaded from non-public Huawei website):
1. Start a TFTP server in the directory where
the firmware upgrade package is located
2. Boot to u-boot as described above
3. Install firmware upgrade package and format the config partitions:
> update system FatAP6X10XN_SOMEVERSION.bin
> format_fs
Return to factory firmware (from previously created backup):
1. Copy over the firmware partition backup to /tmp,
for example using scp
2. Use sysupgrade with force to restore the backup:
sysupgrade -F huawei_ap6010dn_fw_backup.bin
3. Boot AP to U-Boot as described above
Quirks and known issues:
- The stock firmware has a semi dual boot concept where the primary
kernel uses a squashfs as root partition and the secondary kernel uses
an initramfs. This dual boot concept is circumvented on purpose to gain
more flash space and since the stock firmware's flash layout isn't
compatible with mtdsplit.
- The external watchdog's timeout of 1.6s is very hard to satisfy
during bootup. This is why the GPIO15 pin connected to the watchdog input
is configured directly in the LZMA loader to output the AHB_CLK/2 signal
which keeps the watchdog happy until the wdt-gpio kernel driver takes
over. Because it would also take too long to read the whole kernel image
from flash, the uImage header only includes the loader which then reads
the kernel image from flash after GPIO15 is configured.
Signed-off-by: Marco von Rosenberg <marcovr@selfnet.de>
Link: https://github.com/openwrt/openwrt/pull/15941
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tianling Shen [Sat, 6 Jul 2024 07:30:31 +0000 (15:30 +0800)]
mediatek: add ABT ASR3000 support
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: 128 MB SPI-NAND
RAM: 256MB
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset, Mesh
Power: DC 12V 1A
Gain telnet access:
1. Login into web interface, and download the configuration.
2. Decode and uncompress the configuration:
* Enter fakeroot if you are not login as root.
base64 -d e-xxxxxxxxxxxx-cfg.tar.gz | tar -zx
3. Edit 'etc/passwd', remove root password: 'root::1:0:99999:7:::'.
4. Edit 'etc/rc.local', insert telnetd command before 'exit 0':
( sleep 3s; /usr/sbin/telnetd; ) &
5. Repack the configuration:
tar -zc etc/ | base64 > e-xxxxxxxxxxxx-cfg.tar.gz
6. Upload new configuration via web interface, now you can connect to
ASR3000 via telnet.
Flash instructions:
1. Connect to ASR3000, backup everything, especially 'Factory' part.
2. Write new BL2:
mtd write openwrt-mediatek-filogic-abt_asr3000-preloader.bin BL2
3. Write new FIP:
mtd write openwrt-mediatek-filogic-abt_asr3000-bl31-uboot.fip FIP
4. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt has booted, perform sysupgrade.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/15887
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Mieczyslaw Nalewaj [Wed, 19 Jun 2024 12:49:44 +0000 (14:49 +0200)]
ramips: mt7620: remove kmod-switch-rtl8366-smi from package list
Remove kmod-switch-rtl8366-smi from the package list, as it is still loaded
because kmod-switch-rtl8367b depends on it
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15757
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Aleksander Jan Bajkowski [Sat, 13 Jul 2024 10:36:02 +0000 (12:36 +0200)]
lantiq: fix checkpatch warnings in etop driver
This commit fixes all errors reported by the checkpatch script. This
should make it easier to accept upstream this patch.
There should be no functional changes.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/15939
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Aleksander Jan Bajkowski [Sat, 13 Jul 2024 10:11:34 +0000 (12:11 +0200)]
lantiq: properly release descriptors in etop driver detach
This patch fixes two issues in the driver detach:
* double free of the same descriptor (upstream bug, backported in
66177c081f1b05e4eb7f6c23d97954e8172c4336),
* releasing tx descriptor instead of rx (downstream bug).
The driver is compiled into the kernel that is why the error
is not visible in normal use.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/15939
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Sean Khan [Sat, 13 Jul 2024 20:40:30 +0000 (16:40 -0400)]
mac80211: fix kconf build warnings
This patch cleans up the following warnings during build:
"warning: format not a string literal"
```
conf.c: In function 'conf_askvalue':
conf.c:89:17: warning: format not a string literal and no format arguments [-Wformat-security]
89 | printf(_("(NEW) "));
| ^~~~~~
conf.c: In function 'conf_choice':
conf.c:285:33: warning: format not a string literal and no format arguments [-Wformat-security]
285 | printf(_(" (NEW)"));
| ^~~~~~
conf.c: In function 'check_conf':
conf.c:440:41: warning: format not a string literal and no format arguments [-Wformat-security]
440 | printf(_("*\n* Restart config...\n*\n"));
| ^~~~~~
conf.c: In function 'main':
conf.c:617:41: warning: format not a string literal and no format arguments [-Wformat-security]
617 | _("\n*** The configuration requires explicit update.\n\n"));
| ^
conf.c:669:25: warning: format not a string literal and no format arguments [-Wformat-security]
669 | fprintf(stderr, _("\n*** Error during writing of the configuration.\n\n"));
| ^~~~~~~
conf.c:673:25: warning: format not a string literal and no format arguments [-Wformat-security]
673 | fprintf(stderr, _("\n*** Error during update of the configuration.\n\n"));
| ^~~~~~~
conf.c:684:25: warning: format not a string literal and no format arguments [-Wformat-security]
684 | fprintf(stderr, _("\n*** Error during writing of the configuration.\n\n"));
| ^~~~~~~
```
And POSIX Yacc warnings
```
lex -ozconf.lex.c -L zconf.l
yacc -ozconf.tab.c -t -l zconf.y
zconf.y:34.1-7: warning: POSIX Yacc does not support %expect [-Wyacc]
34 | %expect 32
| ^~~~~~~
zconf.y:97.1-11: warning: POSIX Yacc does not support %destructor [-Wyacc]
97 | %destructor {
| ^~~~~~~~~~~
gcc -Wall -Wmissing-prototypes -Wstrict-prototypes -O2 -fomit-frame-pointer -DKBUILD_NO_NLS -c -o zconf.tab.o zconf.tab.c
gcc conf.o zconf.tab.o -o conf
```
After:
gcc -Wall -Wmissing-prototypes -Wstrict-prototypes -O2 -fomit-frame-pointer -DKBUILD_NO_NLS -c -o conf.o conf.c
yacc -Wno-yacc -ozconf.tab.c -t -l zconf.y
gcc -Wall -Wmissing-prototypes -Wstrict-prototypes -O2 -fomit-frame-pointer -DKBUILD_NO_NLS -c -o zconf.tab.o zconf.tab.c
gcc conf.o zconf.tab.o -o conf
Signed-off-by: Sean Khan <datapronix@protonmail.com>
Link: https://github.com/openwrt/openwrt/pull/15953
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tony Ambardar [Mon, 15 Jul 2024 05:21:52 +0000 (22:21 -0700)]
libbpf: Update to v1.4.5
Update to the latest upstream release to include recent improvements and
bugfixes.
Link: https://github.com/libbpf/libbpf/releases/tag/v1.4.5
Link: https://github.com/libbpf/libbpf/releases/tag/v1.4.4
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
John Audia [Thu, 18 Jul 2024 20:15:36 +0000 (16:15 -0400)]
kernel: bump 6.6 to 6.6.41
Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.6.41
Manually rebased:
lantiq/patches-6.6/0028-NET-lantiq-various-etop-fixes.patch
All other patches automatically rebased.
Build system: x86/64
Build-tested: x86/64/AMD Cezanne, flogic/xiaomi_redmi-router-ax6000-ubootmod
Run-tested: x86/64/AMD Cezanne, flogic/xiaomi_redmi-router-ax6000-ubootmod
Signed-off-by: John Audia <therealgraysky@proton.me>
Zxl hhyccc [Thu, 18 Jul 2024 16:45:20 +0000 (00:45 +0800)]
kernel: bump 6.1 to 6.1.100
https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.1.100
All patches automatically rebased.
Build system: bcm53xx ath79
Signed-off-by: Zxl hhyccc <zxlhhy@gmail.com>
Rafał Miłecki [Fri, 12 Jul 2024 09:36:47 +0000 (11:36 +0200)]
base-files: upgrade: nand: use "cmd" argument for extracting command
NAND code uses either "cat" or "zcat" for getting firmware image
content. Code was full of duplicated ${gz}cat calls. Use "cmd" variable
that is determined by a caller and passed to lower level functions. This
avoids code duplication and allows adding support for more formats.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rafał Miłecki [Fri, 12 Jul 2024 09:36:46 +0000 (11:36 +0200)]
base-files: upgrade: nand: document nand_do_upgrade()
Describe what firmware files are supported.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Tianling Shen [Tue, 2 Apr 2024 12:26:45 +0000 (20:26 +0800)]
mediatek: switch to fitblk for cmcc rax3000m
Use the new fitblk driver.
Tested-by: Yangyu Chen <cyy@cyyself.name>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Tianling Shen [Tue, 2 Apr 2024 12:26:45 +0000 (20:26 +0800)]
mediatek: convert eeprom/macaddr to nvmem format for cmcc rax3000m
Switch to new nvmem binding.
Also fixes a issue that the MAC address assigned to lan/wan was
reversed on eMMC boards.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Martin Schiller [Thu, 18 Jul 2024 11:53:37 +0000 (13:53 +0200)]
target.mk: init default configs if they are missing in the .config
The config options that are enabled by default and where other default
packages depends on should not only be set if there is no .config file,
but also if the .config exists but the config option (e.g.
CONFIG_SECCOMP) is missing in the file.
This is relevant, for example, if you are working with .config templates
and then want to complete the configuration using make defconfig.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Martin Schiller [Wed, 17 Jul 2024 11:00:38 +0000 (13:00 +0200)]
target.mk: further improve handling of default enabled SECCOMP
The fix in commit
847fad476f3d ("target.mk: improve handling of default
enabled SECCOMP") unfortunately does not work for targets where the ARCH
variable is set in ./$(SUBTARGET)/target.mk.
To get this working, the ./$(SUBTARGET)/target.mk must be included
before the check.
Fixes: 847fad476f3d ("target.mk: improve handling of default enabled SECCOMP")
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Daniel Golle [Thu, 18 Jul 2024 10:56:13 +0000 (11:56 +0100)]
mediatek: fix platform_copy_config()
Also use env variables exported by export_fitblk_rootdev() in
platform_copy_config().
Fixes: 4448d6325f ("mediatek: make use of common uImage.FIT upgrade functions")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Wed, 17 Jul 2024 15:25:59 +0000 (16:25 +0100)]
base-files: remove fitblk_get_bootdev() from /lib/upgrade/common.sh
The function was moved to /lib/upgrade/fit.sh which is part of the fitblk
package. Remove it from /lib/upgrade/common.sh to safe space on boards
not using unified uImage.FIT images.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Wed, 17 Jul 2024 15:25:05 +0000 (16:25 +0100)]
uboot-envtools: use /lib/upgrade/fit.sh
Use export_fitblk_bootdev() in /lib/upgrade/fit.sh instead of now
deprecated fitblk_get_bootdev() function. Include /lib/upgrade/fit.sh
instead of /lib/upgrade/common.sh to allow removing the function there.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Wed, 17 Jul 2024 15:24:03 +0000 (16:24 +0100)]
mediatek: make use of common uImage.FIT upgrade functions
Use newly introduced fit_do_upgrade() function in /lib/upgrade/platform.sh.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Wed, 17 Jul 2024 15:22:10 +0000 (16:22 +0100)]
fitblk: move shell functions to common file
Move shell functions used for sysupgrade into /lib/upgrade/fit.sh.
Introduce improved fitblk boot device detection function which
works also in case ubiblock devices have not yet been created or
even UBI itself not yet being attached.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Jan Hoffmann [Sat, 13 Jul 2024 12:49:09 +0000 (14:49 +0200)]
omap: re-enable target
The target was marked source-only due do the broken Ethernet port on
some devices. With that fixed, it can be enabled again.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Jan Hoffmann [Sat, 13 Jul 2024 12:49:08 +0000 (14:49 +0200)]
omap: switch back to old cpsw ethernet driver
The new cpsw-switch driver reserves VLAN 1 for internal use, which
conflicts with the default network configuration of OpenWrt.
Switch back to the older cpsw driver to make the network connection on
the affected devices (BeagleBone Black and AM335x EVM) usable again.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Zxl hhyccc [Tue, 16 Jul 2024 06:14:08 +0000 (14:14 +0800)]
kernel: bump 6.1 to 6.1.99
https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.1.99
All patches automatically rebased.
Build system: Kirkwood bcm53xx
Signed-off-by: Zxl hhyccc <zxlhhy@gmail.com>
Christian Marangi [Tue, 16 Jul 2024 17:00:29 +0000 (19:00 +0200)]
imagebuilder: remove initramfs image files
Initramfs images are not supported by imagebuilder. With recent changes
to support Per Device Rootfs, we now generate an image and a vmlinux for
each Rootfs and these additional files are all shipped in the
imagebuilder tar.
Drop these new file and any vmlinux-initramfs as they are not used and
increase the final size of the imagebuilder archive.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
John Audia [Mon, 15 Jul 2024 19:37:46 +0000 (15:37 -0400)]
kernel: bump 6.6 to 6.6.40
Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.6.40
All patches (one in this case) automatically rebased.
Build system: x86/64
Build-tested: x86/64/AMD Cezanne, flogic/glinet_gl-mt6000
Run-tested: x86/64/AMD Cezanne, flogic/glinet_gl-mt6000
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/15956
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sun, 14 Jul 2024 23:06:38 +0000 (01:06 +0200)]
wolfssl: Update to version 5.7.2
This fixes multiple security problems:
* [Medium] CVE-2024-1544
Potential ECDSA nonce side channel attack in versions of wolfSSL before 5.6.6 with wc_ecc_sign_hash calls.
* [Medium] CVE-2024-5288
A private key blinding operation, enabled by defining the macro WOLFSSL_BLIND_PRIVATE_KEY, was added to mitigate a potential row hammer attack on ECC operations.
* [Low] When parsing a provided maliciously crafted certificate directly using wolfSSL API, outside of a TLS connection, a certificate with an excessively large number of extensions could lead to a potential DoS.
* [Low] CVE-2024-5991
In the function MatchDomainName(), input param str is treated as a NULL terminated string despite being user provided and unchecked.
* [Medium] CVE-2024-5814
A malicious TLS1.2 server can force a TLS1.3 client with downgrade capability to use a ciphersuite that it did not agree to and achieve a successful connection.
* [Medium] OCSP stapling version 2 response verification bypass issue when a crafted response of length 0 is received.
* [Medium] OCSP stapling version 2 revocation bypass with a retry of a TLS connection attempt.
Unset DISABLE_NLS to prevent setting the unsupported configuration
option --disable-nls which breaks the build now.
Link: https://github.com/openwrt/openwrt/pull/15948
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Chad Monroe [Mon, 15 Jul 2024 17:37:55 +0000 (10:37 -0700)]
mediatek: filogic: disable eMMC HS400 mode for Mount Stuart series
The eMMC chip used in a small batch of these devices has issues operating
in HS400 mode. Reducing to HS200 mode works around the problem and does
not cause any noticeable performance penalties as smaller chips are not fast
enough to saturate the bus. Root cause analysis is pending.
Signed-off-by: Chad Monroe <chad@monroe.io>
Felix Fietkau [Mon, 15 Jul 2024 09:55:20 +0000 (11:55 +0200)]
uboot-mediatek: fix build error on mt7988-rfb
Remove an unnecessary config option that was breaking the build
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Zxl hhyccc [Fri, 12 Jul 2024 17:37:10 +0000 (01:37 +0800)]
kernel: bump 6.1 to 6.1.98
https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.1.98
All patches automatically rebased.
Build system: bcm53xx ath79
Signed-off-by: Zxl hhyccc <zxlhhy@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15935
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
John Audia [Thu, 11 Jul 2024 20:00:56 +0000 (16:00 -0400)]
kernel: bump 6.6 to 6.6.39
Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.6.39
Manually rebased:
generic/backport-6.6/0080-v6.9-smp-Avoid-setup_max_cpus_namespace_collision_shadowing.patch
Removed upstreamed:
generic/backport-6.6/801-v6.11-gpio-mmio-do-not-calculate-bgpio_bits-via-ngpios.patch[1]
generic/backport-6.6/0081-v6.10-cpu-Fix-broken-cmdline-nosmp-and-maxcpus-0.patch[2]
All other patches automatically rebased.
1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.39&id=
dee87316b5f5f167a201491a774bbd6e10c8dd94
2. https://github.com/gregkh/linux/commit/
69787793e7f0673465c89714d1522fde978bbfa8
Build system: x86/64
Build-tested: x86/64/AMD Cezanne, flogic/glinet_gl-mt6000, flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3
Run-tested: x86/64/AMD Cezanne, flogic/glinet_gl-mt6000, flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3
Signed-off-by: John Audia <therealgraysky@proton.me>
Co-authored-by: Hauke Mehrtens <hauke@hauke-m.de>
Link: https://github.com/openwrt/openwrt/pull/15928
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Daniel Golle [Sun, 14 Jul 2024 18:44:26 +0000 (19:44 +0100)]
fstools: update to git HEAD
408c2cc libfstools: skip JFFS2 padding when BLOCKSIZE was given
013050f fstools: remove redundant F2FS_MINSIZE definition
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Sun, 14 Jul 2024 15:28:42 +0000 (16:28 +0100)]
mediatek: add BPi-R3 mini to platform_check_image()
Add entry for the BananaPi R3 mini to the platform_check_image()
function where it has been missing.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Tue, 9 Jul 2024 16:01:41 +0000 (17:01 +0100)]
uboot-mediatek: remove hard-coded UBI volume numbers
There is no point in hard-coding the UBI volume numbers as we are
dynamically looking up the volume by volume name in all cases by now.
Remove this relict as it causes problems without being useful for
anything.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Shiji Yang [Fri, 5 Jul 2024 05:52:06 +0000 (13:52 +0800)]
uboot-mediatek: refresh device defconfig files
It seems that most of them are manually modified. However, we can
use `make savedefconfig` to generate a clean defconfig file.
Refreshed by:
```
Boards=(
mt7623n_bpir2_defconfig \
mt7623a_unielec_u7623_02_defconfig \
mt7622_bananapi_bpi-r64-sdmmc_defconfig \
mt7622_bananapi_bpi-r64-emmc_defconfig \
mt7622_bananapi_bpi-r64-snand_defconfig \
mt7622_linksys_e8450_defconfig \
mt7622_ubnt_unifi-6-lr-v1_defconfig \
mt7622_ubnt_unifi-6-lr-v2_defconfig \
mt7622_ubnt_unifi-6-lr-v3_defconfig \
ravpower-rp-wd009-ram_defconfig \
mt7621_zbtlink_zbt-wg3526-16m_defconfig \
mt7986_netcore_n60_defconfig \
mt7986a_bpi-r3-emmc_defconfig \
mt7986a_bpi-r3-nor_defconfig \
mt7986a_bpi-r3-sd_defconfig \
mt7986a_bpi-r3-snand_defconfig \
mt7986_xiaomi_redmi-ax6000_defconfig \
mt7986_tplink_tl-xdr4288_defconfig \
mt7986_tplink_tl-xdr6086_defconfig \
mt7986_tplink_tl-xdr6088_defconfig \
mt7981_qihoo-360t7_defconfig \
mt7981_xiaomi_mi-router-wr30u_defconfig \
mt7981_h3c_magic-nx30-pro_defconfig \
mt7986a_glinet_gl-mt6000_defconfig \
mt7981_cmcc_rax3000m-emmc_defconfig \
mt7981_cmcc_rax3000m-nand_defconfig \
mt7981_jcg_q30-pro_defconfig \
mt7986_zyxel_ex5601-t0_defconfig \
mt7981_xiaomi_mi-router-ax3000t_defconfig \
mt7986a_jdcloud_re-cp-03_defconfig \
mt7986a_bpi-r3-mini-emmc_defconfig \
mt7986a_bpi-r3-mini-snand_defconfig \
mt7981_nokia_ea0326gmp_defconfig \
mt7988a_bananapi_bpi-r4-emmc_defconfig \
mt7988a_bananapi_bpi-r4-sdmmc_defconfig \
mt7988a_bananapi_bpi-r4-snand_defconfig \
mt7988a_bananapi_bpi-r4-poe-emmc_defconfig \
mt7988a_bananapi_bpi-r4-poe-sdmmc_defconfig \
mt7988a_bananapi_bpi-r4-poe-snand_defconfig \
mt7622_xiaomi_redmi-router-ax6s-ubi-loader_defconfig \
mt7981_openwrt-one-nor_defconfig \
mt7981_openwrt-one-spi-nand_defconfig \
)
for Board in ${Boards[@]}
do
echo "Refresh board ${Board}"
make ${Board}
make savedefconfig
cat ./defconfig > ./configs/${Board}
done
```
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Shiji Yang [Fri, 5 Jul 2024 05:52:06 +0000 (13:52 +0800)]
uboot-mediatek: update to U-Boot release v2024.07
1. Rename function _do_env_set() to env_do_env_set().
2. Replace kwbimage hack with UBOOT_CUSTOMIZE_CONFIG:
"--disable TOOLS_KWBIMAGE" and "--disable TOOLS_LIBCRYPTO".
3. Disable CONFIG_CMD_BOOTEFI_BOOTMGR for all supported devices
because the newly added UEFI bootmenu entries doesn't work.
4. Enable CONFIG_VERSION_VARIABLE for the OpenWrt One.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Co-authored-by: Daniel Golle <daniel@makrotopia.org>
Felix Fietkau [Sat, 13 Jul 2024 13:31:11 +0000 (15:31 +0200)]
mt76: update to Git HEAD (2024-07-13)
564cd93961fc mt76: sync with upstream changes
3b47d9df427c wifi: mt76: mt7915: fix oops on non-dbdc mt7986
Signed-off-by: Felix Fietkau <nbd@nbd.name>
谢致邦 (XIE Zhibang) [Mon, 17 Jun 2024 16:07:53 +0000 (16:07 +0000)]
netfilter: kmod-nft-netdev: add egress support
The netdev egress hook was added in Linux kernel 5.16.
Link: https://patchwork.ozlabs.org/project/openwrt/patch/tencent_EB1DF62723D08576A747D0DAE16FFB99B505@qq.com/
Signed-off-by: 谢致邦 (XIE Zhibang) <Yeking@Red54.com>
Shiji Yang [Sat, 6 Jul 2024 10:27:19 +0000 (18:27 +0800)]
ramips: fix image recipe for ASUS RT-N56U
The OpenWrt image metadata includes checksum validation. Therefore,
it must be generated at the end.
Fixes: https://github.com/openwrt/openwrt/issues/9045
Fixes: https://github.com/openwrt/openwrt/issues/13674
Link: https://patchwork.ozlabs.org/project/openwrt/patch/TYCP286MB08952FAACDFA234C5E052131BCD82@TYCP286MB0895.JPNP286.PROD.OUTLOOK.COM/
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Tomasz Maciej Nowak [Thu, 11 Jul 2024 19:38:22 +0000 (21:38 +0200)]
tegra: promote kernel 6.6 as default
It has been stable so far. As result of this change drop 5.15 files.
Link: https://patchwork.ozlabs.org/project/openwrt/patch/20240711194120.11563-1-tmn505@terefe.re/
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Shiji Yang [Sat, 13 Jul 2024 08:50:59 +0000 (16:50 +0800)]
rtl8812au-ct: fix build with mac80211 6.9.9 backport
The change_beacon() API has been updated since the 6.7 kernel. Ref:
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.9.9&id=
66f85d57b7109baf8a7d5ee04049ac9412611d35
Fix build error:
../rtl8812au-ct-2022.10.26~
9b2b203a/os_dep/linux/ioctl_cfg80211.c:5984:26: error: initialization of 'int (*)(struct wiphy *, struct net_device *, struct cfg80211_ap_update *)' from incompatible pointer type 'int (*)(struct wiphy *, struct net_device *, struct cfg80211_beacon_data *)' [-Werror=incompatible-pointer-types]
5984 | .change_beacon = cfg80211_rtw_change_beacon,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~
../rtl8812au-ct-2022.10.26~
9b2b203a/os_dep/linux/ioctl_cfg80211.c:5984:26: note: (near initialization for 'rtw_cfg80211_ops.change_beacon')
Link: https://patchwork.ozlabs.org/project/openwrt/patch/TYCP286MB0895A26BA1C0517F2CBE71F0BCA72@TYCP286MB0895.JPNP286.PROD.OUTLOOK.COM/
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Shiji Yang [Sat, 13 Jul 2024 03:47:21 +0000 (11:47 +0800)]
mac80211: rt2x00: remove upstreamed patch
This BBP register fix patch has already been upstreamed. Ref:
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.9.9&id=
50da74e1e8b682853d1e07fc8bbe3a0774ae5e09
Fixes: 1bfcc1ea8a78 ("mac80211: update to version 6.9.9")
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Felix Fietkau [Fri, 12 Jul 2024 16:26:56 +0000 (18:26 +0200)]
ath10k-ct: fix mac80211 backport patch to account for the bump to 6.7
Fixes build error
Fixes: 1bfcc1ea8a78 ("mac80211: update to version 6.9.9")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Thu, 11 Jul 2024 13:03:13 +0000 (15:03 +0200)]
ucode: update to Git HEAD (2024-07-11)
73644a036f5a nl80211: move access to tb array out of uc_nl_convert_attr and below
6e3cf83a77a7 nl80211: add support for multi-attribute arrays
6ff24d5488a9 nl80211: update nl80211.h to latest wireless-next
abc2aef28641 nl80211: add wiphy multi-radio support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Wed, 19 Jun 2024 11:51:47 +0000 (13:51 +0200)]
mac80211: update to version 6.9.9
Brings lots of driver updates and API changes needed for mt76 updates.
Disable iwlwifi and ath11k on 5.15, since backport is too difficult,
and the only remaining targets won't need those drivers.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Fri, 12 Jul 2024 13:04:12 +0000 (15:04 +0200)]
kernel: add mhi bus firmware download backport to 6.1
Required by a newer mac80211 backport
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Robert Marko [Thu, 11 Jul 2024 13:16:27 +0000 (15:16 +0200)]
mvebu: rb5009: wire SFP led by default
There is no reason not to wire up the default netdev trigger for the SFP
LED since we have a separate SFP interface visible.
Link: https://github.com/openwrt/openwrt/pull/15927
Signed-off-by: Robert Marko <robimarko@gmail.com>
Robert Marko [Thu, 11 Jul 2024 13:14:47 +0000 (15:14 +0200)]
mvebu: rb5009: convert LEDs to color/function
Since we are trying to get rid of using labels, lets convert RB5009 to the
function/color combo.
Link: https://github.com/openwrt/openwrt/pull/15927
Signed-off-by: Robert Marko <robimarko@gmail.com>
Robert Marko [Thu, 11 Jul 2024 13:02:28 +0000 (15:02 +0200)]
mvebu: rb5009: fix QCA8081 LED polarity
Currently, QCA8081 LED is never configured and the default configuration
has the LED polarity inverted so it will be lit when there is nothing
connected to the PHY.
So lets define the LED as active-low and configure the trigger via 01_leds.
Fixes: 85d9fd6f0ec7 ("mvebu: add support for RB5009UG+S+IN")
Link: https://github.com/openwrt/openwrt/pull/15927
Signed-off-by: Robert Marko <robimarko@gmail.com>
FUKAUMI Naoki [Thu, 11 Jul 2024 05:01:39 +0000 (14:01 +0900)]
rockchip: stop "heartbeat" LED for Radxa CM3I(E25)
stop "heartbeat" which happens before OpenWrt controls LED. instead,
just turn LED on.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/15913
Signed-off-by: Robert Marko <robimarko@gmail.com>
Daniel Golle [Fri, 12 Jul 2024 01:38:53 +0000 (02:38 +0100)]
ramips: mt7621: reduce MMC clock to 48 MHz
The switch to the upstream mmc-mtk driver caused problems with MT7621
because of unstable too high clock frequency:
[ 49.643291] mmc0: error -88 whilst initialising SD card
[ 49.890047] mmc0: error -88 whilst initialising SD card
[ 50.142414] mmc0: error -88 whilst initialising SD card
[ 50.419218] mmc0: error -88 whilst initialising SD card
...
Fix this by reducing the clock speed to 48 MHz instead of 50 MHz, which
is also the value used in upstream Linux mt7621.dtsi.
With that change applied SD cards work as expected on MT7621 devices
also with the new driver.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Shiji Yang [Tue, 9 Jul 2024 17:26:52 +0000 (01:26 +0800)]
ramips: improve support for HiWiFi HC5861 SDHC
1. Override max clock frequency to a stable value 24 MHz.
2. Use voltage regulator to control the power supply.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Shiji Yang [Tue, 9 Jul 2024 16:16:36 +0000 (00:16 +0800)]
ramips: switch default SDHC driver to kmod-mmc-mtk
Now that the SDHC of MT762{0,1,8} has been supported upstream, it's
time to switch the default driver to the upstream one. We will still
keep the old driver for users to choose from.
Tested on HiWiFi HC5861 (MT7620A) and HiWiFi HC5661A (MT7628N).
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Shiji Yang [Tue, 9 Jul 2024 16:16:36 +0000 (00:16 +0800)]
ramips: make SoC dtsi compatible with upstream mmc-mtk driver
Add all essential MTK SDHC properties to support the new mmc-mtk
driver. Since this driver relies on power regulators, we also
need to enable this feature for MT7620, just like MT762{1,8}.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Co-authored-by: John Thomson <git@johnthomson.fastmail.com.au>
Shiji Yang [Tue, 9 Jul 2024 16:16:36 +0000 (00:16 +0800)]
ramips: modules: add Mediatek MMC driver package
This is the upstream implementation of the MTK SD/SDIO/MMC card
reader driver. It is an alternative solution for the downstream
driver package "kmod-sdhci-mt7620".
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Co-authored-by: John Thomson <git@johnthomson.fastmail.com.au>
Shiji Yang [Tue, 9 Jul 2024 16:16:36 +0000 (00:16 +0800)]
ramips: mtk-sd: initialize pad delay and drive strength
Port vendor register init values to upstream MTK SHDC driver.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Shiji Yang [Tue, 9 Jul 2024 16:16:36 +0000 (00:16 +0800)]
ramips: mtk-mmc: use "cd-inverted" to set CD line polarity
"cd-inverted" is an upstream documented property used to indicate
the CD line is actived high. We will introduce a new upstream SDHC
driver, and this change will make them compatible with each other.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Felix Fietkau [Wed, 3 Jul 2024 15:45:33 +0000 (17:45 +0200)]
mac80211: clear vif private data in order to fix accidental reuse
Fixes potential issues when bringing an interface down and then up again
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Kristian Skramstad [Sat, 6 Jul 2024 07:12:58 +0000 (09:12 +0200)]
firmware: ipq-wifi: update to version 2024-07-04
Added:
[+] qcn9074: add Cambium Networks XE3-4 BDF
[+] ipq60xx: add Cambium Networks XE3-4 BDF
Signed-off-by: Kristian Skramstad <kristian+github@83.no>
Link: https://github.com/openwrt/openwrt/pull/15884
Signed-off-by: Robert Marko <robimarko@gmail.com>
Hauke Mehrtens [Wed, 10 Jul 2024 21:52:41 +0000 (23:52 +0200)]
wireless-regdb: Update to version 2024.07.04
Changes:
2a768c4 wireless-regdb: Update regulatory rules for Mongolia (MN) on 6GHz
04875d9 wireless-regdb: Update regulatory rules for Saudi Arabia (SA) on 6GHz
b7bced8 wireless-regdb: Update regulatory rules for South Africa (ZA) on 6GHz
7bc8615 wireless-regdb: Update regulatory info for Thailand (TH) on 6GHz
f901fa9 wireless-regdb: Update regulatory info for Malaysia (MY) for 2022
d72d288 wireless-regdb: Update regulatory info for Morocco (MA) on 6GHz
414face wireless-regdb: Update regulatory info for Chile (CL) on 6GHz
1156a08 wireless-regdb: Update regulatory info for Mexico (MX) on 6GHz
cc6cf7c wireless-regdb: Update regulatory info for Iceland (IS) on 6GHz
ce03cc0 wireless-regdb: Update regulatory info for Mauritius(MU) on 6GHz
7e37778 wireless-regdb: Update regulatory info for Argentina (AR) on 6GHz
56f3a43 wireless-regdb: Update regulatory info for United Arab Emirates (AE) on 6GHz
3cb8b91 wireless-regdb: Update regulatory info for Colombia (CO) on 6GHz
3682ce5 wireless-regdb: Update regulatory info for Costa Rica (CR) for 2021
dd4ffe7 wireless-regdb: Update regulatory info for Dominican Republic (DO) on 6GHz
f8ef7da wireless-regdb: Update regulatory info for Liechtenstein (LI) on 6GHz
a9ecabe wireless-regdb: Update regulatory info for Jordan (JO) for 2022
5a9fdad wireless-regdb: Update regulatory info for Kenya (KE) for 2022
19326c3 wireless-regdb: Update regulatory info for Macao (MO) for 2024
4838054 wireless-regdb: update regulatory database based on preceding changes
Link: https://github.com/openwrt/openwrt/pull/15921
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
projects / openwrt / staging / svanheule.git / log