brcmfmac: move glom alignment setting to SDIO bus layer

txglomming alignment is a SDIO bus specific feature. It is more
appropriate to place it in SDIO bus layer instead of common layer.

Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: restrict dongle txglom disable to old SDIO core

txglomming is a firmware feature for sdio bus interface. For SDIO
device cores newer than revision 11, the default setting of
firmware should be used instead of disabling it from the host side.

Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: add support for bus specific data command

brcmfmac need to support data command setting for dongle's bus
core. A list must be placed at brcmf_bus structure before calling
brcmf_bus_start in order to be sent by brcmf_c_preinit_dcmds.

Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

bcma: define some additional cores IDs

Some of them are BCM4706 specific AFAWK. Most of them was confirmed on
Netgear WNDR450.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'wl12xx-next' into for-linville

ath9k_htc: Fix IDLE power save

Remove the radio enable/disable stuff and fix the
transition to FULL_SLEEP mode when the device is idle.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_htc: Use atomic operations for op_flags

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_htc: Change default listen interval to 1

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Fix lockdep splat

Cancel the MCI work only when MCI is actually enabled.
Fixes this:

[96833.124051] Call Trace:
[96833.124060]  [<ffffffff810afaf8>] __lock_acquire+0x1518/0x1e40
[96833.124065]  [<ffffffff810ad126>] ? mark_held_locks+0x86/0x110
[96833.124069]  [<ffffffff810ad3ad>] ? trace_hardirqs_on+0xd/0x10
[96833.124073]  [<ffffffff814464f0>] ? _raw_spin_unlock_irq+0x30/0x70
[96833.124078]  [<ffffffff81072968>] ? wait_on_cpu_work+0x98/0xc0
[96833.124082]  [<ffffffff810b0a11>] lock_acquire+0xa1/0x150
[96833.124085]  [<ffffffff81072990>] ? wait_on_cpu_work+0xc0/0xc0
[96833.124088]  [<ffffffff81072990>] ? wait_on_cpu_work+0xc0/0xc0
[96833.124092]  [<ffffffff810729e2>] wait_on_work+0x52/0x120
[96833.124095]  [<ffffffff81072990>] ? wait_on_cpu_work+0xc0/0xc0
[96833.124099]  [<ffffffff81063b3f>] ? del_timer+0x7f/0x110
[96833.124102]  [<ffffffff81072c13>] __cancel_work_timer+0x83/0x130
[96833.124106]  [<ffffffff81072cf0>] cancel_work_sync+0x10/0x20
[96833.124113]  [<ffffffffa065b5cd>] __ath_cancel_work+0x4d/0x60 [ath9k]
[96833.124119]  [<ffffffffa065cf28>] ath9k_config+0x458/0x680 [ath9k]
[96833.124125]  [<ffffffffa065dd1e>] ? ath9k_flush+0x6e/0x1d0 [ath9k]
[96833.124129]  [<ffffffff8144394d>] ? __mutex_unlock_slowpath+0x10d/0x190
[96833.124146]  [<ffffffffa056c7b5>] ieee80211_hw_config+0x135/0x2a0 [mac80211]
[96833.124163]  [<ffffffffa057ebbb>] ieee80211_do_open+0x67b/0xc50 [mac80211]
[96833.124178]  [<ffffffffa057f1fd>] ieee80211_open+0x6d/0x80 [mac80211]
[96833.124183]  [<ffffffff8137a44f>] __dev_open+0x9f/0xf0
[96833.124187]  [<ffffffff8137a701>] __dev_change_flags+0xa1/0x180
[96833.124190]  [<ffffffff8137a898>] dev_change_flags+0x28/0x70
[96833.124195]  [<ffffffff813e1179>] devinet_ioctl+0x659/0x780
[96833.124199]  [<ffffffff8137aea0>] ? dev_ioctl+0x210/0x6d0
[96833.124203]  [<ffffffff813e1db5>] inet_ioctl+0x75/0x90
[96833.124208]  [<ffffffff8135e0e0>] sock_do_ioctl+0x30/0x70
[96833.124211]  [<ffffffff8135e3dd>] sock_ioctl+0x7d/0x2c0
[96833.124218]  [<ffffffff81193c39>] do_vfs_ioctl+0x99/0x580
[96833.124222]  [<ffffffff81447415>] ? sysret_check+0x22/0x5d
[96833.124226]  [<ffffffff811941b9>] sys_ioctl+0x99/0xa0
[96833.124230]  [<ffffffff814473e9>] system_call_fastpath+0x16/0x1b

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: raise aggregation limit to 64k for HT IBSS

mac80211 adds stations in HT IBSS as soon as a frame comes by,
even if the HT capabilities are not known yet (they are often
received later, e.g. in beacons). So far, ampdu factor/density
are only calculated when the station is initially added.

This patch changes this to update ampdu factor/density settings
when starting a blockack session.

Using this patch, we had performance boosts from 60 to 150 MBit/s
between two 2x2 Atheros devices in 5 GHz HT IBSS mode.

Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8192se: Fix double inclusion of header pci.h

The command "make includecheck" yields the following for the rtlwifi tree:

/home/finger/linux-2.6/drivers/net/wireless/rtlwifi/rtl8192se/sw.c: ../pci.h is included more than once.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: Fix IRQ disabled warning

The PCI-based drivers can generate the following warning:

[ 9497.776350] ------------[ cut here ]------------
[ 9497.776366] WARNING: at kernel/softirq.c:159 local_bh_enable_ip+0x7a/0xa0()
[ 9497.776370] Hardware name: 05794NC
[ 9497.776597] Pid: 6413, comm: hostapd Not tainted 3.3.0-4.fc16.x86_64 #1
[ 9497.776601] Call Trace:
[ 9497.776612]  [<ffffffff81057b1f>] warn_slowpath_common+0x7f/0xc0
[ 9497.776633]  [<ffffffffa034a099>] ? rtl_pci_reset_trx_ring+0x199/0x230
[rtlwifi]
[ 9497.776640]  [<ffffffff81057b7a>] warn_slowpath_null+0x1a/0x20
[ 9497.776646]  [<ffffffff8105f06a>] local_bh_enable_ip+0x7a/0xa0
[ 9497.776654]  [<ffffffff815f3ef6>] _raw_spin_unlock_bh+0x16/0x20
[ 9497.776671]  [<ffffffffa03e50de>] destroy_conntrack+0x9e/0x120
[nf_conntrack]
[ 9497.776681]  [<ffffffff81511847>] nf_conntrack_destroy+0x17/0x20
[ 9497.776689]  [<ffffffff814d9c85>] skb_release_head_state+0xe5/0x120
[ 9497.776695]  [<ffffffff814d98b6>] __kfree_skb+0x16/0xa0
[ 9497.776700]  [<ffffffff814d9a35>] kfree_skb+0x45/0xc0
[ 9497.776717]  [<ffffffffa034a099>] rtl_pci_reset_trx_ring+0x199/0x230
[rtlwifi]
[ 9497.776734]  [<ffffffffa034a155>] rtl_pci_start+0x25/0x1d0 [rtlwifi]
[ 9497.776750]  [<ffffffffa03440b5>] rtl_op_start+0x55/0x90 [rtlwifi]
[ 9497.776785]  [<ffffffffa02c4956>] ieee80211_do_open+0x296/0xa10 [mac80211]
[ 9497.776794]  [<ffffffff815f7ddd>] ? notifier_call_chain+0x4d/0x70
[ 9497.776828]  [<ffffffffa02c513d>] ieee80211_open+0x6d/0x80 [mac80211]
[ 9497.776836]  [<ffffffff814e8b3f>] __dev_open+0x8f/0xe0
[ 9497.776842]  [<ffffffff814e8de1>] __dev_change_flags+0xa1/0x180
[ 9497.776847]  [<ffffffff814e8f78>] dev_change_flags+0x28/0x70
[ 9497.776856]  [<ffffffff8154e99d>] devinet_ioctl+0x61d/0x7b0
[ 9497.776863]  [<ffffffff8154ef55>] inet_ioctl+0x75/0x90
[ 9497.776870]  [<ffffffff814cdd50>] sock_do_ioctl+0x30/0x70
[ 9497.776876]  [<ffffffff814cee09>] sock_ioctl+0x79/0x2f0
[ 9497.776885]  [<ffffffff81193498>] do_vfs_ioctl+0x98/0x550
[ 9497.776891]  [<ffffffff811939e1>] sys_ioctl+0x91/0xa0
[ 9497.776897]  [<ffffffff815fc029>] system_call_fastpath+0x16/0x1b
[ 9497.776902] ---[ end trace 22886c442489082d ]---

The cause is due to calling kfree_skb() with interrupts disabled.

This bug is discussed in https://bugzilla.redhat.com/show_bug.cgi?id=797709.

Reported-and-Tested by: Ivan Ivanovich <iivanich@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'for-john' of git://git.sipsolutions.net/mac80211-next

wlcore: print stack trace in every recovery

As recovery queuing can now occur from multiple code paths
it's convenient to know what triggered it in all cases
other than an intended recovery which is part of the
switch between single role to multi role.

Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wlcore: queue recovery in case of bus errors during cmd_remove_peer

Following the addition of propagating errors from the bus ops
there's a need to distinguish between bus errors (including timeout)
and a legitimate timeout occuring in cmd_wait_for_event_or_timeout.
In case of real bus errors we need to queue recovery even in cases
where a timeout on a response from the FW to a command is acceptable.

Reported-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wlcore: fix broken TX due to wrong queuing of recovery

commit 14bba17b "wl12xx: Propagate errors from wl1271_raw_write32"
breaks down TX in certain scenarios. wl1271_irq_locked() propagates
errors from wl1271_tx_work_locked however it may return -EBUSY
when the FW queues are full which is a legitimate case and not a
a real error. In this case a recovery is triggered by wl1271_irq
and this keeps repeating itself so TX is completely broken.
Fix it by avoiding propagating return values as errors even if they
aren't. Only bus (SDIO or SPI) ops failures would be progagated
as only these should trigger recovery.

Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wlcore: fix some failure cases in wlcore_probe()

We need to release the IRQ if hw_info() or identify_chip() fails.  And
we need unregister the HW with mac80211 if there are any failures
after it's registered.

Signed-off-by: Luciano Coelho <coelho@ti.com>

wl18xx: deprecate PG1 support

The new PG2 version of the chip has a few differences in terms of FW
API if compared to PG1.  PG1 is just a sample that shouldn't be used
in real life, so to avoid having to handle both separately, mark the
PG1 version as deprecated and bail out during probe.

Signed-off-by: Luciano Coelho <coelho@ti.com>

mac80211: make ieee80211_check_concurrent_iface netdev-independent

ieee80211_check_concurrent_iface() need not use the
netdev. Remove the use of the netdev here to prepare
the function for P2P device addition.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: remove unused function

Remove the unused function is_ieee80211_device().

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

nl80211: specify RSSI threshold in scheduled scan

Support configuring an RSSI threshold in dBm (s32) when requesting
scheduled scan, below which a BSS won't be reported by the cfg80211
driver.

Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211_hwsim: fix smatch/sparse complaints

The code is fine in both cases as-is, but we can
write it slightly differently to fix smatch/sparse
complaints:
 * compare the skb pointer (which we use as a cookie)
   by casting the skb to unsigned long rather than the
   cookie to a pointer (fixes "different address spaces")
 * when transmitting, data->channel must be assigned,
   don't check it (fixes "dereferenced before check")

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: trace debug messages

It can be very useful to have all debug messages
available when debugging, but hard to correlate
between different sources, so add a trace event
for all mac80211 debug messages.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: rename driver-trace file

This file will contain more soon, so
rename it to just trace.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: clean up debugging

There are a few things that make the logging and
debugging in mac80211 less useful than it should
be right now:
 * a lot of messages should be pr_info, not pr_debug
 * wholesale use of pr_debug makes it require *both*
   Kconfig and dynamic configuration
 * there are still a lot of ifdefs
 * the style is very inconsistent, sometimes the
   sdata->name is printed in front

Clean up everything, introducing new macros and
separating out the station MLME debugging into
a new Kconfig symbol.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wlcore: prevent recovery in the middle of resume

Take the mutex early in the resume handler and use the locked version of
the IRQ routine. This ensures any recoveries queued will only take place
after resume has fully completed.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wlcore: refactor threaded IRQ routine

Separate the threaded IRQ handling routine into two functions.
The outer function takes the mutex and calls recovery on errors. It also
performs a Tx-path optimization to avoid redundant works.

The inner function is simplified - all calls to recovery are removed and
it assumes the lock is taken. The locked variant will be reused elsewhere.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wlcore: check Rx-filter functions in the suspend path

Propagate some missing return values for Rx-filter related functions.
This and makes sure we always fail the suspend in case of SDIO errors.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wlcore: force recovery on resume if suspended without recovering

If an error is detected after mac80211 is already suspended, the recovery
work will not be queued. This will leave the driver in a bad state on
resume.

Detect this in the resume op and re-queue a recovery.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wlcore: don't allow SDIO read/writes after failure

Set a flag and after the first read/write failure is encountered.
This flag will disallow further SDIO read/writes until op_stop() is
executed, which will clear all flags.

This prevents further errors from occurring, since one error usually
indicates that IO operations won't work anymore until the chip is
rebooted.  By blocking more calls, we avoid extra timeouts and having
to wait for them to occur.

[Added second paragraph explaining why the change is needed. -- Luca]

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wlcore: cancel suspend when recovery is pending

We wish to postpone suspend if recovery is pending. This will make sure
the FW is in a good state and perform wowlan wakeup.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wlcore: access the firmware memory via debugfs

Applications running in the user space needs access to the
memory of the chip. Examples of such access
- read/write global variables
- access to firmware log
- dump memory after firmware panic event

Arbitrary 4-bytes aligned location can be accessed by
read/write file wlcore/mem

[Check return value of wlcore_raw_read/write and wlcore_set_partition
calls as required by the recent IO changes. -- Luca]

Signed-off-by: Arkady Miasnikov <a-miasnikov@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

rtlwifi: Change debug level for deletion of an entry in CAM

When running in AP mode, the driver reports all deletions from CAM in
a cryptic manner that makes users think it is an error. change so that
the condition is only reported at higher-levels of debugging.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: fix smatch warning in ar9003_hw_spur_mitigate_mrc_cck

drivers/net/wireless/ath/ath9k/ar9003_phy.c:211
ar9003_hw_spur_mitigate_mrc_cck() error: potential NULL dereference
'spur_fbin_ptr'.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: rename mrcCCKOff to fix smatch warning

Rename mrcCCKOff for better code readability and also fixes
the smatch warning.

drivers/net/wireless/ath/ath9k/ar9003_phy.c:982
ar9003_hw_ani_control() Error invalid range 1 to 0.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmsmac: fix NULL pointer crash in brcms_c_regd_init()

In the function brcms_c_regd_init() the channels are validated
against the device capabilities. This is done for both 2.4G and
5G band, but there are devices that are 2.4G only, ie. BCM4313.
For that device this leads to a NULL dereference. This patch adds
a check in brcms_c_regd_init() to fix this.

Issue introduced in wireless-next tree by following commit:
cf03c5d brcm80211: smac: inform mac80211 of the X2 regulatory domain

Cc: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: make inclusion of vmalloc.h explicit fixing linux-next build

This patch fixes problem detected in linux-next build for powerpc
allyesconfig. The error message below is no longer observed:

  CC      drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.o
drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.c: In function 'brcmf_sdio_dump_console':
drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.c:3085: error: implicit declaration of function 'vzalloc'
drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.c:3085: warning: assignment makes pointer from integer without a cast
drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.c:3113: error: implicit declaration of function 'vfree'
make[2]: *** [drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.o] Error 1

Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: enhance power save for USB and PCIe chipsets

FW will not explicitly notify about host sleep activation to the
host for USB and PCIe chipsets. Hence host should generate Host
Sleep Activated event as soon as Host Sleep parameters are
configured to FW successfully.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: wake up main thread to handle Tx traffic if scan is delayed/aborted

This is a flaw in recently implemented logic to handle Tx traffic
and scan operation simultaneously. We missed to wakeup main thread
to handle Tx traffic if scan is delayed/aborted.

For some cards (SD8797, for example), firmware will send SLEEP event
if there is no activity for 50msec. While handling the SLEEP event,
main thread will be woken up and Tx packet gets sent hence. In worst
case Tx traffic will be delayed for 50msec.

For other cards, such as USB8797, firmware won't send SLEEP event.
So, Tx traffic gets stuck if no other event triggers the wakeup of
main thread.

This patch fixes above issues.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: parse WPA IE and support WPA/WPA2 mixed mode for uAP

Add support for parsing WPA IE from beacon parameter of
cfg80211_ap_settings and set it to FW.

WPA/WPA2 mixed mode is supported with this patch.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'for-linville' of git://git./linux/kernel/git/luca/wl12xx

Merge branch 'for-john' of git://git./linux/kernel/git/iwlwifi/iwlwifi-next

Merge branch 'for-john' of git://git.sipsolutions.net/mac80211-next

mac80211: pass sdata to some RX functions

For better debugging, we would like to have
the sdata pointer available later, so pass
it into these functions.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: two small verbose debug cleanups

Two instances of CONFIG_MAC80211_VERBOSE_DEBUG
should be different, fix them.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: remove TKIP debug

The TKIP code hasn't been changed in a very long
time, so it seems unlikely that anyone really has
a need for the TKIP debug code. Remove it.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wlcore: Force checking of io functions' return values

All io functions' return values should be propagated and handled. Add a
__must_check annotation to verify that the return values are checked and
to avoid future mistakes.

Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wlcore: Propagate errors from wl1271_read_hwaddr

Propagate errors from wl1271_read_hwaddr. This function is only used
when reading the FW log (following a recovery), so don't read the FW log
in case of a bus error.

Also rename prefixes of wlcore functions which their prototypes had to
be changed.

Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wlcore: Propagate errors from wl1271_raw_write32

Propagate errors from wl1271_raw_write32 and request for recovery when
appropriate.
Also rename prefixes of wlcore functions which their prototypes had to
be changed.

Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wlcore: Propagate errors from wl1271_raw_read32

Propagate errors from wl1271_raw_read32. Since the read functions had no
way of returning errors in-band, change their prototypes.
Also rename prefixes of wlcore functions which their prototypes had to
be changed.

Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wlcore: Propagate errors from wl1271_write

Propagate errors from wl1271_write and request for recovery when
appropriate.
Also rename prefixes of wlcore functions which their prototypes had to
be changed.

Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wlcore: Propagate errors from wl1271_read

Propagate errors from wl1271_read and request for recovery when
appropriate.
Also rename prefixes of wlcore functions which their prototypes had to
be changed.

Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wlcore: Propagate errors from wlcore_raw_*_data functions

wlcore_raw_read_data is called when the FW status is read which happens
while handling interrupts and when the FW log is read following a
recovery. Request a recovery in the former case, and don't read the FW
log in case the FW status read failed.

Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wlcore: Change raw io functions to return errors

Make wl1271_raw_write and wl1271_raw_read return errors so the driver
could handle these appropriately.
Since the prototype has changed, also rename the prefix of these
functions to wlcore.

Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wlcore: Change read/write ops to return errors

While bus operations may fail, either due to HW or FW issues, these are
never propagated to higher layers. As a result, the core driver has no
way of knowing that the operations failed, and will only recover if high
level logic requires it (e.g. no command completion).

Change read/write bus operations to return errors to let higher layer
functionality handle these.

Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wlcore: Disable interrupts while recovering

In case a recovery is initiated, the FW can no longer be trusted, and
the driver should not handle any new FW events.

Disable the interrupt handler when a recovery is scheduled and balance
it back in the op_stop callback.

Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wlcore: Fix sdio out-of-sync power state

wl12xx_sdio_power_off() manually powers down the card regardless of the
runtime pm state. If wl12xx_sdio_power_on() is called before the card
was suspended by runtime PM, it will not power up the card.

As part of the HW detection, the chip's power is toggled. Since this
happens in the context of probing sdio, the power reference counter will
be higher than zero. As a result, when wl12xx_sdio_power_off() is
called, the chip will be powered down while still having a positive
power reference counter. If the interface is quickly activated, the
driver might try to transfer data to a powered off chip.

Fix this by ensuring that wl12xx_sdio_power_on() explicitly powers on
the chip in case runtime pm claims the chip is already powered on. To
avoid cases in which it is not possible to determine if the chip was
really powered on (card's power reference counter is positive), operate
on the mmc_card instead of the function.

Also verify that the chip is indeed powered on before powering off, to
avoid wrong reference counter values in error cases.

Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

ieee80211: more OUI type definitions for WLAN_OUI_MICROSOFT

WMM and WPS

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: add command to get current rssi

Get current rssi (in dBm) from the driver/FW.

Instead of reporting the signal received in the last
rx packet, which might be inaccurate if rx traffic is
low and beacon filtering is enabled, get the signal
from the driver/FW.

Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Merge branch 'wl12xx-next' into for-linville

Conflicts:
drivers/net/wireless/ti/wl18xx/main.c

wl18xx: use %zu for size_t arguments in printk calls

After 934b9d1e (wl18xx: avoid some -Wformat warnings) there was still
a warning with (at least) ARM gcc version 4.4.1:

drivers/net/wireless/ti/wl18xx/main.c: In function 'wl18xx_conf_init':
drivers/net/wireless/ti/wl18xx/main.c:1026: warning: format '%ld' expects type 'long int', but argument 2 has type 'unsigned int'

Fix this by using %zu for the both formats, since the fw->size and the
macro (derived from sizeof()) are size_t.

Signed-off-by: Luciano Coelho <coelho@ti.com>

wl18xx: split siso40 HT cap between 2Ghz and 5Ghz

Remove the cap IEEE80211_HT_CAP_DSSSCCK40 from the 5Ghz variant of
the siso40 HT capabilities. It is meaningless in 5Ghz.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wl18xx: sane defaults for HT capabilities

Introduce a default set of HT capabilities that are set according to the
number of antennas on the board. Move the HT setting code down to allow
the number of antennas to be set (and optionally overridden) before it.

Remove the "mimo" HT option, since the default mode now enables MIMO is
possible.

Use this opportunity to add a helper function for setting HT
capabilities and reduce the volume of the code a bit.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wl18xx: explicitly remove the 5Ghz MIMO HT cap

The 18xx chip does not support MIMO in 5Ghz. Use the siso20 HT cap as
fallback in 5Ghz when "mimo" is requested.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wlcore: read FW logs from FW memory on watchdog recovery

FW uses a few memory blocks as a buffer to accumulate FW logs before
transmitting them to the host over SDIO. When FW WatchDog recovery
occurs, the last FW traces are still pending in the buffer. Driver is
to read these FW traces whether log mode is continuous or on demand.

FW memory blocks allocated for the log buffer are handled as a link list:
the first 4 bytes in each memory block contain FW address to the next block.
The end of list condition depends on FW log mode:
- on demand: the list is cyclic, the next address is equal to the first address
- continuous: the address is  equal to 0x2000000

Log data resides inside FW memory block with offset depending on
logger mode:
- on demand:  4 bytes (address of the next memory block)
- continuous: 4 bytes and Rx Descriptor structure size

Described FW logger API is backward compatible with previous FW versions.

Signed-off-by: Igal Chernobelsky <igalc@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wlcore: do not report noise level in get survey op

The get survey op expects the low level driver to report
the noise level for a a given channel.

The noise calculated in wlcore is (rssi-snr/2), but since
the snr reported by the FW is a derivative from the rssi
this calculation is useless, and should not be reported
to the user space.

Reporting incorrect noise, results in the wpa_supplicant
miscalculating the roaming candidate priority, thus causing
a situation where an AP with a lower rssi level would be
chosen over a better AP.

Signed-off-by: Yoni Divinsky <yoni.divinsky@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wl18xx: set Tx align quirk for PG2

Before patch b5d6d9b (wlcore/wl12xx/wl18xx: don't use TX align quirk
for wl127x), this was automatically set for all platforms. As this
should now be set explicitly, set it for PG2 as well.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wl18xx: increase Rx descriptors for PG2

New PG2 firmwares have additional Rx descriptors.

Add a module parameter to manually set the number of Rx descriptors for
older versions (PG1). We cannot discriminate based on chip-id, since
this value must be set on probe.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wlcore: reconfigure sleep_auth when removing interfaces

The sleep_auth value of the last interface to be set up prevailed when
an interface was removed. Take care of this by correctly configuring the
value according to the remaining STA/AP interfaces.

Take this opportunity to refactor the sleep_auth setting code for better
readability.

[Small style fix. -- Luca]

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wlcore: allow setting sleep_auth before interface init

Hold a value for sta_sleep_auth that is amenable to change by debugfs.
When detecting a legal value in this variable on interface init, use it
as an override value for sleep_auth.

This makes debugging more intuitive using the debugfs value.

Increment the conf version since we added an element to the conf
structure.

Note: An AP going up will always set sleep_auth to PSM_CAM.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wlcore: add a debugfs entry to allow changing the sleep mode by hand

For FW debugging purposes, we may need to change the sleep mode
(aka. sleep_auth) by hand, and set it to the mode we want.  To allow
this, a debugfs entry is added.

Now we store the sleep_auth value that has been set and use that
instead of the quirk to decide whether we should enter ELP or not.

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>

wlcore: suppress error message on Rx BA session removal

The ampdu_action() function is called on the reconfig() path to remove
existing Rx BA sessions. Since these don't exist for the low level
driver, we output an error message. Turn the message into a debug
message for now, until the mac80211 reconfig flow is changed.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

iwlwifi: limit mac_change_interface to BSS context

Currently when mac80211 asks to change the interface
type, we will accept it for both the BSS and PAN
contexts. This is not terribly complicated today,
but with the addition of the P2P Device abstraction
the PAN context handling will get more complex, so
restrict mac_change_interface to the BSS context.

Also fix a small locking issue and use is_active
instead of the vif pointer to check if the other
context is activated, guarding exclusive interface
types on the BSS context (IBSS) against the PAN
context being used for something else.

Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

iwlwifi: increase scan timeout

When the first interface is active, then scanning
on it or the second interface can take a little
longer than 7s (I observed around 8s.) Bump the
timeout to 15s to avoid aborting a scan that is
still running, just taking more time.

Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

iwlwifi: fix radio reset scan dwell vs. quiet time

My previous commit to shorten the radio reset time
caused issues as the firmware checks the active
dwell time against the quiet time, asserting that
the dwell is >= quiet time. This isn't really
needed in case of passive scanning like here, but
of course we need to pass that check.

To fix this, override the quiet time to be the
same as the radio reset dwell time.

Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

rtlwifi: rtl8192se: Fix gcc 4.7.x warning

With gcc 4.7.x, the following warning is issued as the routine that sets
the array has the possibility of not initializing the values:

  CC [M]  drivers/net/wireless/rtlwifi/rtl8192se/phy.o
drivers/net/wireless/rtlwifi/rtl8192se/phy.c: In function ‘rtl92s_phy_set_txpower’:
drivers/net/wireless/rtlwifi/rtl8192se/phy.c:1268:23: warning: ‘ofdmpowerLevel[0]’ may be used uninitialized in this function [-Wuninitialized]

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: do not sampling on ani timer when chip is in sleep

The baseband and cycle counters are being sampled during ani
processing for debugging purpose. Whenever the ani is postponded
due to sleep state, taking samples on that time is of no use and
also unneccesarily waking up the chip might increase the power
consumption on idle associated state. Hence moving debug function
within powersave block.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: fix LNA control on WLAN sleep

When WLAN enter full sleep mode, WLAN HW should send out a LNA_TAKE
message for BT to take control of the shared LNA. Otherwise BT traffic
is completely stopped whenever the wlan interface is moved full sleep
mode.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: update ar9462 dac_async_fifo initval

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: fix mci_is_enabled utility

During driver stop, btcoex is disabled and also btcoex_hw.enabled
is set to false. Afterwards mci_is_enabled returns false so that
BT is not gaining SPDT control on WLAN sleep. Fix that.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: fix BT mute at hw init

WLAN driver initialization is muting BT which is terminating
the ongoing BT traffic. The reason to mute BT is to avoid any
incoming MCI messages from BT when MCI reset is in progress that
could corrupt WLAN MCI RX state machine. But we should not
dedicate radio completely to WLAN in driver init itself. So this
patch removes the wlan weightage changes from mute BT to retain
BT connection.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: fix incorrect profile type manupulation

Two MCI interrupts are generated while adding A2DP and headset profiles
with different types and same connection handle. While disconnecting,
only one MCI interrupt is generated with last added profile type value
for both profiles.

While adding second profile type decrement first one.

Signed-off-by: Bala Shanmugam <bkamatch@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl1251: send filters to firmware as they are set

Firmware supports changing filters using ACX_RX_CFG command,
so use it in .configure_filter callback. Firmware also supports
probe request filtering, so add it too along the way.
This will also re-enable BSSID filter which is now removed by
join command while associating.

Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl1251: fix filtering support

This driver has a hack in cmd.c which effectively disables all filtering.
This seems to be triggering a firmware bug where it stops reporting any
rx packets after random time on some routers, which is eliminated (or at
least appears much more rarely) when filtering is on.
I have found that only BSSID filter needs to be disabled for association
to work, so disable only that instead of all filtering.

Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl1251: remove unused filter_work

filter_work is never used, remove it.

Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: smac: use current regulatory domain when checking whether OFDM is allowed

The brcmsmac internal regulatory data is being used to determine whether
OFDM should be allowed, and this is only done once during
initialization. To be effective this needs to be checked against
mac80211's regulatory rules for the current channel.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: smac: don't validate channels against internal regulatory data

The core regulatory support will disable channels not allowed by
regulatory rules, so brcmsmac doesn't need to check whether or not the
requested channel is permitted by regulatory.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: smac: use mac80211 channel data for tx power limits

Currently the limits from the internal X2 domain are used, regardless
of what regulatory rules are in effect. Instead use the power limits set
by the higher-level regulatory support.

The rules for the MIMO power limits are still always derived from the
world domain, pending guidance from Broadcom as to how these need to be
handled. This will be fixed later, but using the limits from the world
domain works for now.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: smac: enable/disable radio on regulatory updates

Currently the radio disable state is only updated during initialization,
and it's only checked against the internal world domain. This is
unnecessary, as there are always valid channels against this domain.
Instead, check whether any channels are enabled in the regulatory
notifier and update the radio state accordingly.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: smac: inform mac80211 of the X2 regulatory domain

brcmsmac implements enforcement of regulatory constraints internally,
using a Broadcom-specific world roaming domain named X2. Besides being
duplication of functionality this can also conflict with mac80211's
regulatory implementation, as mac80211 is unaware of the X2 domain and
thus might apply a more restrictive domain.

This patch is the first step in making brcmsmac cooperate with
mac80211's regulatory support. X2 is registered as a custom domain with
mac80211, so that at least both implementations will be enforcing the
same set of constraints. The internal enforcement of rules is kept for
now; this will be converted over to relying on mac80211 regulatory
enforcement in later patches.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: smac: clean up channel.c

Much of the code is either unsed or never put to any useful purpose.
Remove this code in advance of reworking the driver's regulatory
support.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Brett Rudley <brudley@broadcom.com>
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: smac: remove unused code for 40MHz channels

This code has been kept around in anticipation of adding support for
40MHz channels, but subsequent patches to better integrate with mac80211
regulatory support will render it completely broken. Therefore we should
go ahead and remove it.

Keep these changes separate from other cleanup patches in order to make
it easier to resurrect 40MHz channel support at some point in the
future.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: smac: always set channel specified by mac80211

In some situations brcmsmac is choosing a channel internally. This makes
it difficult at times to know what channel to use for enforcing
regulatory constraints, so instead always use the channel from the
mac80211 configuration.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: smac: don't set up tx power limits during initialization

This code is unnecessary, and in fact it's never executed because the
interface is never up when brcms_c_channels_commit() is called. Removing
it helps simplify the implementation of proper regulatory support.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Brett Rudley <brudley@broadcom.com>
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: support for WEP in AP mode

This patch adds support for WEP open/shared encryption in AP mode.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: separate uAP WPA/WPA2 parsing from other BSS parameters

To enhance readability, create a separate function for parsing
WPA/WPA2 related parameters from cfg80211_ap_settings.
There is no functional change in this patch.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: set HT capability based on cfg80211_ap_settings

Parse HT IE from cfg80211 and set HT capabilities accordingly
to FW. If HT IE is missing, 11n would be disabled in FW.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: set channel via start_ap handler for AP interface

This patch adds functionality to set channel info received from
cfg80211_ap_settings in start_ap handler.

Since set_channel cfg80211 handler has been removed and we need
not explicitely call mwifiex_uap_set_channel(); hence this
function definition is also removed.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wireless: rtl818x: rtl8180 add devices ids

from windows driver:
0x1186, 0x3301 D-Link Air DWL-510 Wireless PCI Adapter
0x1432, 0x7106 LevelOne WPC-0101 11Mbps Wireless PCMCIA CardBus Adapter

Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: clean up ANI OFDM trigger handling

Adjust ah->config.ofdm_trig_{high,low} when setting noise immunity values
to simplify threshold checks in ath9k_hw_ani_monitor

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>