git.openwrt.org Git - openwrt/staging/blogic.git/log

drm: meson: crtc: use proper macros instead of magic constants

This patch add new macros which describe couple bits field of the
following registers:
- VD1_BLEND_SRC_CTRL
- VPP_SC_MISC

Signed-off-by: Julien Masson <jmasson@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/86wohb82fa.fsf@baylibre.com

drm: meson: mask value when writing bits relaxed

The value used in the macro writel_bits_relaxed has to be masked since
we don't want change the bits outside the mask.

Signed-off-by: Julien Masson <jmasson@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/86y31r82fo.fsf@baylibre.com

drm/panel: simple: Support TI nspire panels

This adds support for the TI nspire panels to the simple panel
roster. This code is based on arch/arm/mach-nspire/clcd.c.
This includes likely the first grayscale panel supported.

These panels will be used with the PL11x DRM driver.

Cc: Daniel Tang <dt.tangr@gmail.com>
Cc: Fabian Vogt <fabian@ritter-vogt.de>
Tested-by: Fabian Vogt <fabian@ritter-vogt.de>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190805085847.25554-4-linus.walleij@linaro.org

drm/panel: simple: Add TI nspire panel bindings

Add bindings for the TI NSPIRE simple display panels.

Cc: devicetree@vger.kernel.org
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190806135437.7451-1-linus.walleij@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

drm/pl111: Support grayscale

Migrating the TI nspire calculators to use the PL111 driver for
framebuffer requires grayscale support for the elder panel
which uses 8bit grayscale only.

DRM does not support 8bit grayscale framebuffers in memory,
but by defining the bus format to be MEDIA_BUS_FMT_Y8_1X8 we
can get the hardware to turn on a grayscaling feature and
convert the RGB framebuffer to grayscale for us.

Cc: Daniel Tang <dt.tangr@gmail.com>
Cc: Fabian Vogt <fabian@ritter-vogt.de>
Tested-by: Fabian Vogt <fabian@ritter-vogt.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190805085847.25554-2-linus.walleij@linaro.org

drm/panfrost: Add madvise and shrinker support

Add support for madvise and a shrinker similar to other drivers. This
allows userspace to mark BOs which can be freed when there is memory
pressure.

Unlike other implementations, we don't depend on struct_mutex. The
driver maintains a list of BOs which can be freed when the shrinker
is called. Access to the list is serialized with the shrinker_lock.

Cc: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Acked-by: Alyssa Rosenzweig <alyssa.rosenzweig@collabora.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190805143358.21245-2-robh@kernel.org

drm/shmem: Add madvise state and purge helpers

Add support to the shmem GEM helpers for tracking madvise state and
purging pages. This is based on the msm implementation.

The BO provides a list_head, but the list management is handled outside
of the shmem helpers as there are different locking requirements.

Cc: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Eric Anholt <eric@anholt.net>
Acked-by: Acked-by: Alyssa Rosenzweig <alyssa.rosenzweig@collabora.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190805143358.21245-1-robh@kernel.org

drm/panfrost: Remove completed features still in TODO

There's a few features the driver supports which we forgot to remove, so
remove them now.

Cc: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190802195727.1963-1-robh@kernel.org

drm/rockchip: fix VOP_WIN_GET macro

Commit 9a61c54b9bff ("drm/rockchip: vop: group vop registers") seems to
have unintentionally changed the defintion of this macro. Since it is
unused, this was not spotted but any attempt to use it results in
compilation errors.

Revert to the previous definition.

Fixes: 9a61c54b9bff ("drm/rockchip: vop: group vop registers")
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20190703095111.29117-1-john@metanate.com

Revert "drm/gem: Rename drm_gem_dumb_map_offset() to drm_gem_map_offset()"

This reverts commit 220df83a5394fbf7c1486ba7848794b7b351d598.

Turns out drm_gem_dumb_map_offset really only worked for the dumb buffer
case, so revert the name change.

Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20190807145253.2037-2-sean@poorly.run

Revert "drm/panfrost: Use drm_gem_map_offset()"

This reverts commit 583bbf46133c726bae277e8f4e32bfba2a528c7f.

Turns out we need mmap to work on imported BOs even if the current code
is buggy.

Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20190807145253.2037-3-sean@poorly.run

drm/vgem: drop DRM_AUTH usage from the driver

The authentication can be circumvented, by design, by using the render
node.

From the driver POV there is no distinction between primary and render
nodes, thus we can drop the token.

Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190527081741.14235-11-emil.l.velikov@gmail.com

drm/msm: drop DRM_AUTH usage from the driver

The authentication can be circumvented, by design, by using the render
node.

From the driver POV there is no distinction between primary and render
nodes, thus we can drop the token.

Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: freedreno@lists.freedesktop.org
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190527081741.14235-7-emil.l.velikov@gmail.com

drm/nouveau: remove open-coded drm_invalid_op()

Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: nouveau@lists.freedesktop.org
Signed-off-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190522150219.13913-2-emil.l.velikov@gmail.com

Revert "drm/nouveau: remove open-coded drm_invalid_op()"

This reverts commit ccdae42575695ab442941310bd67c7ed1714e273.

Mandatory review was missing from this patch.

Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190807142101.251400-6-sean@poorly.run

Revert "drm/msm: drop DRM_AUTH usage from the driver"

This reverts commit 88209d2c5035737f96bcfc2fd73c0fd8d80e9bf1.

Mandatory review was missing from this patch.

Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190807142101.251400-5-sean@poorly.run

Revert "drm/vgem: drop DRM_AUTH usage from the driver"

This reverts commit e4eee93d25776da998ec2dfaabe7d2206598d26d.

Mandatory review was missing from this patch.

Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190807142101.251400-4-sean@poorly.run

Revert "Revert "drm/panfrost: Use drm_gem_map_offset()""

This reverts commit be855382bacb5ccfd24f9be6098d87acf4cfbb15.

Mandatory review was missing from this patch.

Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190807142101.251400-3-sean@poorly.run

Revert "Revert "drm/gem: Rename drm_gem_dumb_map_offset() to drm_gem_map_offset()""

This reverts commit 415d2e9e07574d3de63b8df77dc686e0ebf64865.

Mandatory review was missing from this patch.

Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190807142101.251400-2-sean@poorly.run

drm/sti: fix opencoded use of drm_panel_*

Use the drm_panel_(enable|disable|get_modes) functions.

Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Vincent Abriou <vincent.abriou@st.com>
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190804201637.1240-9-sam@ravnborg.org

dma-buf: simplify reservation_object_get_fences_rcu a bit

We can add the exclusive fence to the list after making sure we got
a consistent state.

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/322034/?series=64786&rev=1

drm/i915: stop using seqcount for fence pruning

After waiting for a reservation object use reservation_object_test_signaled_rcu
to opportunistically prune the fences on the object.

This allows removal of the seqcount handling in the reservation object.

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/322032/?series=64786&rev=1

dma-buf: fix shared fence list handling in reservation_object_copy_fences

Add some helpers to correctly allocate/free reservation_object_lists.

Otherwise we might forget to drop dma_fence references on list destruction.

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/322031/?series=64786&rev=1

dma-buf: fix busy wait for new shared fences

When reservation_object_add_shared_fence is replacing an old fence with a new
one we should not drop the old one before the new one is in place.

Otherwise other cores can busy wait for the new one to appear.

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/322030/

drm/crc-debugfs: Add notes about CRC<->commit interactions

CRC generation can be impacted by commits coming from userspace, and
enabling CRC generation may itself trigger a commit. Add notes about
this to the kerneldoc.

Changes since v1:
- Clarified that anything that would disable CRCs counts as a full
modeset, and so userspace needs to reconfigure after full modesets

Changes since v2:
- Add these notes
- Rebase onto drm-misc-next (trivial conflict in comment)

Signed-off-by: Brian Starkey <brian.starkey@arm.com>
Signed-off-by: Ayan Kumar Halder <ayan.halder@arm.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link:- https://patchwork.freedesktop.org/patch/321974/

drm/hdcp: reference for srm file format

In the kernel documentation, HDCP specifications links are shared as a
reference for SRM table format.

v2:
Fixed small nits. [Shashank]

Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
Acked-by: Pekka Paalanen <pekka.paalanen@collabora.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/320968/?series=57232&rev=14

drm/i915: update the hdcp state with uevent

drm function to update the content protection property state and to
generate a uevent is invoked from the intel hdcp property work.

Hence whenever kernel changes the property state, userspace will be
updated with a uevent.

v2:
state update is moved into drm function [daniel]

Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Pekka Paalanen <pekka.paalanen@collabora.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/320965/?series=57232&rev=14

drm/hdcp: update content protection property with uevent

drm function is defined and exported to update a connector's
content protection property state and to generate a uevent along
with it.

Pekka have completed the Weston DRM-backend review in
https://gitlab.freedesktop.org/wayland/weston/merge_requests/48
and the UAPI for HDCP 2.2 looks good.

The userspace is accepted in Weston.

v2:
  Update only when state is different from old one.
v3:
  KDoc is added [Daniel]
v4:
  KDoc is extended bit more [pekka]
v5:
  Uevent usage is documented at kdoc of "Content Protection" also
  [pekka]

Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Pekka Paalanen <pekka.paalanen@collabora.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/320963/?series=57232&rev=14

drm: uevent for connector status change

DRM API for generating uevent for a status changes of connector's
property.

This uevent will have following details related to the status change:

  HOTPLUG=1, CONNECTOR=<connector_id> and PROPERTY=<property_id>

Pekka have completed the Weston DRM-backend review in
https://gitlab.freedesktop.org/wayland/weston/merge_requests/48
and the UAPI for HDCP 2.2 looks good.

The userspace is accepted in Weston.

v2:
  Minor fixes at KDoc comments [Daniel]
v3:
  Check the property is really attached with connector [Daniel]
v4:
  Typos and string length suggestions are addressed [Sean]

Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Sean Paul <sean@poorly.run>
Acked-by: Pekka Paalanen <pekka.paalanen@collabora.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/320961/?series=57232&rev=14

drm/i915: Attach content type property

Attaches the content type property for HDCP2.2 capable connectors.

Implements the update of content type from property and apply the
restriction on HDCP version selection.

Need ACK for content type property from userspace consumer.

v2:
  s/cp_content_type/content_protection_type [daniel]
  disable at hdcp_atomic_check to avoid check at atomic_set_property
[Maarten]
v3:
  s/content_protection_type/hdcp_content_type [Pekka]
v4:
  hdcp disable incase of type change is moved into commit [daniel].
v5:
  Simplified the Type change procedure. [Daniel]
v6:
  Type change with UNDESIRED state is ignored.

Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Pekka Paalanen <pekka.paalanen@collabora.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/320959/?series=57232&rev=14

drm: Add Content protection type property

This patch adds a DRM ENUM property to the selected connectors.
This property is used for mentioning the protected content's type
from userspace to kernel HDCP authentication.

Type of the stream is decided by the protected content providers.
Type 0 content can be rendered on any HDCP protected display wires.
But Type 1 content can be rendered only on HDCP2.2 protected paths.

So when a userspace sets this property to Type 1 and starts the HDCP
enable, kernel will honour it only if HDCP2.2 authentication is through
for type 1. Else HDCP enable will be failed.

Pekka have completed the Weston DRM-backend review in
https://gitlab.freedesktop.org/wayland/weston/merge_requests/48
and the UAPI for HDCP 2.2 looks good.

The userspace is accepted in Weston.

v2:
  cp_content_type is replaced with content_protection_type [daniel]
  check at atomic_set_property is removed [Maarten]
v3:
  %s/content_protection_type/hdcp_content_type [Pekka]
v4:
  property is created for the first requested connector and then reused.
[Danvet]
v5:
  kernel doc nits addressed [Daniel]
  Rebased as part of patch reordering.
v6:
  Kernel docs are modified [pekka]
v7:
  More details in Kernel docs. [pekka]
v8:
  Few more clarification into kernel doc of content type [pekka]
v9:
  Small fixes in coding style.
v10:
  Moving DRM_MODE_HDCP_CONTENT_TYPEx definition to drm_hdcp.h [pekka]

Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Pekka Paalanen <pekka.paalanen@collabora.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/320957/?series=57232&rev=14

drm/bochs: Use dev_get_drvdata

Instead of using to_pci_dev + pci_get_drvdata,
use dev_get_drvdata to make code simpler.

Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20190723101103.30250-1-hslester96@gmail.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>

drm/qxl: Use dev_get_drvdata where possible

Instead of using to_pci_dev + pci_get_drvdata,
use dev_get_drvdata to make code simpler.

Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20190723103959.4078-1-hslester96@gmail.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>

drm/ttm: drop ttm_buffer_object->resv

All users moved to ttm_buffer_object->base.resv

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20190805140119.7337-18-kraxel@redhat.com

drm/virtio: switch driver from bo->resv to bo->base.resv

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Christian König <christian.koenig@amd.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20190805140119.7337-17-kraxel@redhat.com

drm/qxl: switch driver from bo->resv to bo->base.resv

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Christian König <christian.koenig@amd.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20190805140119.7337-16-kraxel@redhat.com

drm/nouveau: switch driver from bo->resv to bo->base.resv

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20190805140119.7337-15-kraxel@redhat.com

drm/amdgpu: switch driver from bo->resv to bo->base.resv

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20190805140119.7337-14-kraxel@redhat.com

drm/vmwgfx: switch driver from bo->resv to bo->base.resv

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Thomas Hellstrom <thellstrom@vmware.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20190805140119.7337-13-kraxel@redhat.com

drm/radeon: switch driver from bo->resv to bo->base.resv

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20190805140119.7337-12-kraxel@redhat.com

drm/ttm: switch ttm core from bo->resv to bo->base.resv

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20190805140119.7337-11-kraxel@redhat.com

drm/ttm: set both resv and base.resv pointers

Initialize both ttm_buffer_object->resv and ttm_buffer_object->base.resv
pointers. This allows to move users from the former to the latter. When
all users are moved we can drop ttm_buffer_object->resv.

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20190805140119.7337-10-kraxel@redhat.com

drm/ttm: use gem vma_node

Drop vma_node from ttm_buffer_object, use the gem struct
(base.vma_node) instead.

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20190805140119.7337-9-kraxel@redhat.com

drm/ttm: use gem reservation object

Drop ttm_resv from ttm_buffer_object, use the gem reservation object
(base._resv) instead.

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20190805140119.7337-8-kraxel@redhat.com

drm/nouveau: use embedded gem object

Drop drm_gem_object from nouveau_bo, use the
ttm_buffer_object.base instead.

Build tested only.

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Christian König <christian.koenig@amd.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20190805140119.7337-7-kraxel@redhat.com

drm/amdgpu: use embedded gem object

Drop drm_gem_object from amdgpu_bo, use the
ttm_buffer_object.base instead.

Build tested only.

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20190805140119.7337-6-kraxel@redhat.com

drm/radeon: use embedded gem object

Drop drm_gem_object from radeon_bo, use the
ttm_buffer_object.base instead.

Build tested only.

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20190805140119.7337-5-kraxel@redhat.com

drm/qxl: use embedded gem object

Drop drm_gem_object from qxl_bo, use the
ttm_buffer_object.base instead.

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Christian König <christian.koenig@amd.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20190805140119.7337-4-kraxel@redhat.com

drm/vram: use embedded gem object

Drop drm_gem_object from drm_gem_vram_object, use the
ttm_buffer_object.base instead.

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: http://patchwork.freedesktop.org/patch/msgid/20190805140119.7337-3-kraxel@redhat.com

drm/ttm: add gem base object

Add drm_gem_object struct to ttm_buffer_object, so ttm objects are a gdm
object superclass. Add a function to check whenever a given bo actually
uses the embedded drm_gem_object.

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20190805140119.7337-2-kraxel@redhat.com

backlight: drop EARLY_EVENT_BLANK support

There was no users left - so drop the code to support EARLY_EVENT_BLANK.
This patch removes the support in backlight,
and drop the notifier in fbmem.

That EARLY_EVENT_BLANK is not used can be verified that no driver set any of:

lcd_ops.early_set_power()
lcd_ops.r_early_set_power()

Noticed while browsing backlight code for other reasons.

v2:
- Fix changelog to say "EARLY_EVENT_BLANK" (Daniel)

Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: "Michał Mirosław" <mirq-linux@rere.qmqm.pl>
Cc: Peter Rosin <peda@axentia.se>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-fbdev@vger.kernel.org
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190725143224.GB31803@ravnborg.org

drm/bridge/parade: Drop legacy GPIO header

This driver uses the new GPIO API from <linux/gpio/consumer.h>
so drop the inclusion of the legacy header.

Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190708113154.12985-1-linus.walleij@linaro.org

drm/bridge/nxp-ptn3460: Drop legacy GPIO headers

This driver uses exclusively the new GPIO API from
<linux/gpio/consumer.h> so just drop the old API headers.

Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190708113009.12723-1-linus.walleij@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

drm/bridge/megachips: Drop GPIO header

This file isn't using any interfaces from <linux/gpio.h> so
just drop the include.

Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190708112803.12432-1-linus.walleij@linaro.org

drm/pl111: Fix unused variable warning

drivers/gpu/drm/pl111/pl111_display.c: In function ‘pl111_display_init’:
drivers/gpu/drm/pl111/pl111_display.c:551:17: warning: unused variable
‘dev’ [-Wunused-variable]
struct device *dev = drm->dev;
^
Fixes: d6781e490179 ("drm/pl111: Drop special pads config check")
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Eric Anholt <eric@anholt.net>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1564996456-55677-1-git-send-email-zhangshaokun@hisilicon.com

dma-buf: fix stack corruption in dma_fence_chain_release

We can't free up the chain using recursion or we run into a stack overflow.

Manually free up the dangling chain nodes to avoid recursion.

Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Fixes: 7bf60c52e093 ("dma-buf: add new dma_fence_chain container v7")
Link: https://patchwork.freedesktop.org/patch/321612/

dma-buf: add more reservation object locking wrappers

Complete the abstraction of the ww_mutex inside the reservation object.

This allows us to add more handling and debugging to the reservation
object in the future.

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/320761/

drm/vblank: drop use of DRM_WAIT_ON()

DRM_WAIT_ON() is from the deprecated drm_os_linux header and
the modern replacement is the wait_event_*.

The return values differ, so a conversion is needed to
keep the original interface towards userspace.
Introduced a switch/case to make code obvious.

Analysis from Michel Dänzer:

The waiting condition rely on all relevant places where vblank_count
is modified calls wake_up(&vblank->queue).

drm_handle_vblank():
- Calls wake_up(&vblank->queue)

drm_vblank_enable():
- There is no need here because there can be no sleeping waiters
  in the queue, because vblank->enabled == false immediately
  terminates any waits.

drm_crtc_accurate_vblank_count():
- This is called from interrupt handlers, at least from
  amdgpu_dm.c:dm_pflip_high_irq(). Not sure it needs to wake up
  the queue though, the driver should call
  drm_(crtc_)_handle_vblank anyway.

drm_vblank_disable_and_save():
- It can be called from an interrupt, via drm_handle_vblank ->
  vblank_disable_fn. However, the only place where
  drm_vblank_disable_and_save can be called with sleeping waiters
  in the queue is in drm_crtc_vblank_off, which wakes up the queue
  afterwards (which terminates all waits, because
  vblank->enabled == false at this point).

v3:
- Added analysis to changelog from Michel Dänzer
- Moved return result handling inside if (req_seq != seq) (Daniel V)
- Reused more of the former logic - resulting in simpler code
- Dropped Reviewed-by from Sean Paul as this is a new implementation

v2:
- Fix so the case where req_seq equals seq was handled properly
- quick hack to check if IGT became happy
- Only sent to igt, not to dri-devel

Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Cc: Sean Paul <sean@poorly.run>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190726210658.GA6299@ravnborg.org

drm/pl111: Drop special pads config check

This drops the check of the surplus "pads" configuration
from the device tree that is completely unused in the DRM
driver.

This was only used to work around limitations in the earlier
fbdev driver.

Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Liviu Dudau <Liviu.Dudau@arm.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190724134959.2365-2-linus.walleij@linaro.org

drm/pl111: Deprecate the pads from the DT binding

The pads were an earlier workaround for the internal image
pipeline in the Linux fbdev subsystem. As we move to generic
definition of display properties and drivers that no longer
need this to work, deprecate this property.

Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Liviu Dudau <Liviu.Dudau@arm.com>
Cc: devicetree@vger.kernel.org
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190724134959.2365-1-linus.walleij@linaro.org

drm/komeda: Enable dual-link support

Komeda HW can support dual-link which splits display frame to two halves
(left/link0, right/link1) and output them by two output links.
Due to the halved pixel rate of each link, the pxlclk of dual-link can be
reduced two times compare with single-link.

For enabling dual-link:
- The DT need to configure two output-links for the pipeline node.
- Komeda enable dual-link when both link0 and link1 have been connected.

Example of how the pipeline node will look like for dual-link setup

pipe0: pipeline@0 {
clocks = <&fpgaosc2>;
clock-names = "pxclk";
reg = <0>;

#address-cells = <1>;
#size-cells = <0>;

port@0 {
reg = <0>;

#address-cells = <1>;
#size-cells = <0>;
dp0_pipe0_link0: endpoint@0 {
reg = <0>;
remote-endpoint = <&dlink_connector_in0>;

};
dp0_pipe0_link1: endpoint@1 {
reg = <1>;
remote-endpoint = <&dlink_connector_in1>;
};
};
};

Signed-off-by: James Qian Wang (Arm Technology China) <james.qian.wang@arm.com>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190618081013.13638-3-james.qian.wang@arm.com

drm/komeda: Use drm_display_mode "crtc_" prefixed hardware timings

struct drm_display_mode contains two copies of timings.
- plain timings.
- hardware timings, the ones with "crtc_" prefix.
According to the definition, update komeda to use the hardware timing.

Signed-off-by: James Qian Wang (Arm Technology China) <james.qian.wang@arm.com>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190618081013.13638-2-james.qian.wang@arm.com

drm/drm_debugfs_crc.c: Document that .verify_crc_source vfunc is required for enabling CRC support.

drm_debugfs_crtc_crc_add() function checks that both .set_crc_source and
.verify_crc_source hooks are provided before enabling debugfs support for
reading per-frame CRC data. Make that explicit in the documentation.

Cc: Daniel Vetter <daniel@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190703150330.21992-1-Liviu.Dudau@arm.com

drm: mali-dp: Mark expected switch fall-through

Now that -Wimplicit-fallthrough is passed to GCC by default, the
following warnings shows up:

../drivers/gpu/drm/arm/malidp_hw.c: In function ‘malidp_format_get_bpp’:
../drivers/gpu/drm/arm/malidp_hw.c:387:8: warning: this statement may fall
through [-Wimplicit-fallthrough=]
    bpp = 30;
    ~~~~^~~~
../drivers/gpu/drm/arm/malidp_hw.c:388:3: note: here
   case DRM_FORMAT_YUV420_10BIT:
   ^~~~
../drivers/gpu/drm/arm/malidp_hw.c: In function ‘malidp_se_irq’:
../drivers/gpu/drm/arm/malidp_hw.c:1311:4: warning: this statement may fall
through [-Wimplicit-fallthrough=]
    drm_writeback_signal_completion(&malidp->mw_connector, 0);
    ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
../drivers/gpu/drm/arm/malidp_hw.c:1313:3: note: here
   case MW_START:
   ^~~~

Rework to add a 'break;' in a case that didn't have it so that
the compiler doesn't warn about fall-through.

Cc: stable@vger.kernel.org # v5.2+
Fixes: b8207562abdd ("drm/arm/malidp: Specified the rotation memory requirements for AFBC YUV formats")
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190730153056.3606-1-anders.roxell@linaro.org

drm/tilcdc: Remove obsolete crtc_mode_valid() hack

Earlier there were no mode_valid() helper for crtc and tilcdc had a
hack to over come this limitation. But now the mode_valid() helper is
there (has been since v4.13), so it is about time to get rid of that
hack.

Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/

Revert "drm/radeon: Provide ddc symlink in connector sysfs directory"

This reverts commit bed7a2182de6833f5d0f990a656bffb1c6000c70.

It causes the following build error:
../drm/radeon/radeon_connectors.c: In function 'radeon_add_legacy_connector':
../drm/radeon/radeon_connectors.c:2433:5: error: 'ddc' undeclared (first use in this function)
ddc = &radeon_connector->ddc_bus->adapter;
^~~

Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190801115313.22562-1-narmstrong@baylibre.com

drm/radeon: Provide ddc symlink in connector sysfs directory

Use the ddc pointer provided by the generic connector.

Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/0836f34238730afce3f4d6b13f5cf04f832b668a.1564161140.git.andrzej.p@collabora.com

drm/amdgpu: Provide ddc symlink in connector sysfs directory

Use the ddc pointer provided by the generic connector.

Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/7fee0fa0d0f77af6595d283d5f3ae5d551475821.1564161140.git.andrzej.p@collabora.com

drm/bridge: ti-tfp410: Provide ddc symlink in connector sysfs directory

Use the ddc pointer provided by the generic connector.

Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/3b61da77a6456805db0deffe6d1a2343dd784730.1564161140.git.andrzej.p@collabora.com

drm/bridge: dw-hdmi: Provide ddc symlink in connector sysfs directory

Use the ddc pointer provided by the generic connector.

Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/4bcf0f154c683c9787fa34f911ebc52de6b4a7a1.1564161140.git.andrzej.p@collabora.com

drm/bridge: dumb-vga-dac: Provide ddc symlink in connector sysfs directory

Use the ddc pointer provided by the generic connector.

Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ebb75e71b8b7c8d65d54a947a03fd21b8969fb3a.1564161140.git.andrzej.p@collabora.com

drm/ast: Provide ddc symlink in connector sysfs directory

Use the ddc pointer provided by the generic connector.

Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ff968add8074d109aeed02f0708edd85138246c3.1564161140.git.andrzej.p@collabora.com

drm/mgag200: Provide ddc symlink in connector sysfs directory

Use the ddc pointer provided by the generic connector.

Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/d9e8d4281f6778e5598410a44f1b29c85df1c16d.1564161140.git.andrzej.p@collabora.com

drm: sti: Provide ddc symlink in hdmi connector sysfs directory

Use the ddc pointer provided by the generic connector.

Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/510765aff8ef99683aa2da48bd08004376b1980a.1564161140.git.andrzej.p@collabora.com

drm/imx: imx-tve: Provide ddc symlink in connector's sysfs

Use the ddc pointer provided by the generic connector.

Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1c660776741760b8094484268b670a09da8a9042.1564161140.git.andrzej.p@collabora.com

drm/imx: imx-ldb: Provide ddc symlink in connector's sysfs

Use the ddc pointer provided by the generic connector.

Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/bcfe39a0333df951a7d160b3a946c2c32e7eac7f.1564161140.git.andrzej.p@collabora.com

drm/sun4i: hdmi: Provide ddc symlink in sun4i hdmi connector sysfs directory

Use the ddc pointer provided by the generic connector.

Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/b5a8881b226a9af7d31eb6a57d7fe0fccdcb3a47.1564161140.git.andrzej.p@collabora.com

drm: Add drm_connector_init() variant with ddc

Allow passing ddc adapter pointer to the init function. Even if
drm_connector_init() sometime in the future decides to e.g. memset() all
connector fields to zeros, the newly added function ensures that at its
completion the ddc member of connector is correctly set.

Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/3915224ae895240fd0973cf7f06b9d453e4d8520.1564161140.git.andrzej.p@collabora.com

drm: Add ddc link in sysfs created by drm_connector

Add generic code which creates symbolic links in sysfs, pointing to ddc
interface used by a particular video output. For example:

ls -l /sys/class/drm/card0-HDMI-A-1/ddc
lrwxrwxrwx 1 root root 0 Jun 24 10:42 /sys/class/drm/card0-HDMI-A-1/ddc \
-> ../../../../soc/13880000.i2c/i2c-2

This makes it easy for user to associate a display with its ddc adapter
and use e.g. ddcutil to control the chosen monitor.

This patch adds an i2c_adapter pointer to struct drm_connector. Particular
drivers can then use it instead of using their own private instance. If a
connector contains a ddc, then create a symbolic link in sysfs.

Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/d470def6cd661b777faeee67b5838a4623c4010e.1564161140.git.andrzej.p@collabora.com

drm/gm12u320: Move driver to drm/tiny

Move the driver to the new haven for tiny DRM drivers.

Cc: Hans de Goede <hdegoede@redhat.com>
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190725105132.22545-4-noralf@tronnes.org

drm/tinydrm: Rename folder to tiny

The drm in tinydrm is superfluous so rename to tiny.

Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190725105132.22545-3-noralf@tronnes.org

drm/tinydrm/Kconfig: Remove menuconfig DRM_TINYDRM

This makes the tiny drivers visible by default without having to enable a
knob.

Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com> to it once
Link: https://patchwork.freedesktop.org/patch/msgid/20190725105132.22545-2-noralf@tronnes.org

drm/prime: Ditch gem_prime_res_obj hook

Everyone is just using gem_object->resv now.

Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20190725132655.11951-5-daniel.vetter@ffwll.ch

drm/amdgpu: Fill out gem_object->resv

That way we can ditch our gem_prime_res_obj implementation. Since ttm
absolutely needs the right reservation object all the boilerplate is
already there and we just have to wire it up correctly.

Note that gem/prime doesn't care when we do this, as long as we do it
before the bo is registered and someone can call the handle2fd ioctl
on it.

Aside: ttm_buffer_object.ttm_resv could probably be ditched in favour
of always passing a non-NULL resv to ttm_bo_init(). At least for gem
drivers that would avoid having two of these, on in ttm_buffer_object
and the other in drm_gem_object, one just there for confusion.

Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: "Michel Dänzer" <michel.daenzer@amd.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Huang Rui <ray.huang@amd.com>
Cc: Felix Kuehling <Felix.Kuehling@amd.com>
Cc: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Cc: Evan Quan <evan.quan@amd.com>
Cc: Sonny Jiang <sonny.jiang@amd.com>
Cc: Amber Lin <Amber.Lin@amd.com>
Cc: "Michał Mirosław" <mirq-linux@rere.qmqm.pl>
Cc: Junwei Zhang <Jerry.Zhang@amd.com>
Cc: Thomas Zimmermann <contact@tzimmermann.org>
Cc: Samuel Li <Samuel.Li@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190725132655.11951-4-daniel.vetter@ffwll.ch

drm/nouveau: Fill out gem_object->resv

That way we can ditch our gem_prime_res_obj implementation. Since ttm
absolutely needs the right reservation object all the boilerplate is
already there and we just have to wire it up correctly.

Note that gem/prime doesn't care when we do this, as long as we do it
before the bo is registered and someone can call the handle2fd ioctl
on it.

Aside: ttm_buffer_object.ttm_resv could probably be ditched in favour
of always passing a non-NULL resv to ttm_bo_init(). At least for gem
drivers that would avoid having two of these, on in ttm_buffer_object
and the other in drm_gem_object, one just there for confusion.

Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: nouveau@lists.freedesktop.org
Reviewed-by: Ben Skeggs <bskeggs@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190725132655.11951-3-daniel.vetter@ffwll.ch

drm/radeon: Fill out gem_object->resv

That way we can ditch our gem_prime_res_obj implementation. Since ttm
absolutely needs the right reservation object all the boilerplate is
already there and we just have to wire it up correctly.

Note that gem/prime doesn't care when we do this, as long as we do it
before the bo is registered and someone can call the handle2fd ioctl
on it.

Aside: ttm_buffer_object.ttm_resv could probably be ditched in favour
of always passing a non-NULL resv to ttm_bo_init(). At least for gem
drivers that would avoid having two of these, on in ttm_buffer_object
and the other in drm_gem_object, one just there for confusion.

Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: "David (ChunMing) Zhou" <David1.Zhou@amd.com>
Cc: amd-gfx@lists.freedesktop.org
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190725132655.11951-2-daniel.vetter@ffwll.ch

drm/rockchip: Make analogix_dp_atomic_check static

Fix sparse warning:

drivers/gpu/drm/bridge/analogix/analogix_dp_core.c:1151:5: warning:
symbol 'analogix_dp_atomic_check' was not declared. Should it be static?

Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190730150057.57388-1-yuehaibing@huawei.com

drm/syncobj: fix leaking dma_fence in drm_syncobj_query_ioctl

We need to check the context number instead if the previous sequence to detect
an error and if an error is detected we need to drop the reference to the
current fence or otherwise would leak it.

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Fixes: 27b575a9aa2f ("drm/syncobj: add timeline payload query ioctl v6")
Link: https://patchwork.freedesktop.org/patch/319123/

drm: sti: Mark expected switch fall-throughs

Mark switch cases where we are expecting to fall through.

This patch fixes the following warning (Building: arm):

drivers/gpu/drm/sti/sti_hdmi.c: In function ‘hdmi_audio_configure’:
drivers/gpu/drm/sti/sti_hdmi.c:851:13: warning: this statement may fall through [-Wimplicit-fallthrough=]
   audio_cfg |= HDMI_AUD_CFG_CH78_VALID;
drivers/gpu/drm/sti/sti_hdmi.c:852:2: note: here
  case 6:
  ^~~~
drivers/gpu/drm/sti/sti_hdmi.c:853:13: warning: this statement may fall through [-Wimplicit-fallthrough=]
   audio_cfg |= HDMI_AUD_CFG_CH56_VALID;
drivers/gpu/drm/sti/sti_hdmi.c:854:2: note: here
  case 4:
  ^~~~
drivers/gpu/drm/sti/sti_hdmi.c:855:13: warning: this statement may fall through [-Wimplicit-fallthrough=]
   audio_cfg |= HDMI_AUD_CFG_CH34_VALID | HDMI_AUD_CFG_8CH;
drivers/gpu/drm/sti/sti_hdmi.c:856:2: note: here
  case 2:
  ^~~~

Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190729222752.GA20277@embeddedor

drm/mst: Fix sphinx warnings in drm_dp_msg_connector register functions

Fixes the following warnings:

../drivers/gpu/drm/drm_dp_mst_topology.c:1593: warning: Excess function parameter 'drm_connector' description in 'drm_dp_mst_connector_late_register'
../drivers/gpu/drm/drm_dp_mst_topology.c:1613: warning: Excess function parameter 'drm_connector' description in 'drm_dp_mst_connector_early_unregister'
../drivers/gpu/drm/drm_dp_mst_topology.c:1594: warning: Function parameter or member 'connector' not described in 'drm_dp_mst_connector_late_register'
../drivers/gpu/drm/drm_dp_mst_topology.c:1614: warning: Function parameter or member 'connector' not described in 'drm_dp_mst_connector_early_unregister'

Fixes: 562836a269e3 ("drm/dp_mst: Enable registration of AUX devices for MST ports")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Lyude Paul <lyude@redhat.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190726142057.224121-1-sean@poorly.run

drm/rockchip: Use drm_atomic_helper_commit_tail_rpm

Now that we use the drm psr helpers, we no longer need to hand-roll our
atomic_commit_tail implementation. So use the helper

Changes in v2:
- None
Changes in v3:
- None
Changes in v4:
- None
Changes in v5:
- None

Link to v1: https://patchwork.freedesktop.org/patch/msgid/20190228210939.83386-6-sean@poorly.run
Link to v2: https://patchwork.freedesktop.org/patch/msgid/20190326204509.96515-5-sean@poorly.run
Link to v3: https://patchwork.freedesktop.org/patch/msgid/20190502194956.218441-11-sean@poorly.run
Link to v4: https://patchwork.freedesktop.org/patch/msgid/20190508160920.144739-12-sean@poorly.run

Cc: Zain Wang <wzz@rock-chips.com>
Cc: Tomasz Figa <tfiga@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190611160844.257498-12-sean@poorly.run

drm/rockchip: Don't fully disable vop on self refresh

Instead of fully disabling and re-enabling the vop on self refresh
transitions, only disable the active windows. This will speed up
self refresh exits substantially and is still a power-savings win.

This patch integrates portions of Zain's patch from here:
https://patchwork.kernel.org/patch/9615063/

Changes in v2:
- None
Changes in v3:
- None
Changes in v4:
- Adjust for preceding vop_win_disable changes
Changes in v5:
- None

Link to v1: https://patchwork.freedesktop.org/patch/msgid/20190228210939.83386-5-sean@poorly.run
Link to v2: https://patchwork.freedesktop.org/patch/msgid/20190326204509.96515-4-sean@poorly.run
Link to v3: https://patchwork.freedesktop.org/patch/msgid/20190502194956.218441-10-sean@poorly.run
Link to v4: https://patchwork.freedesktop.org/patch/msgid/20190508160920.144739-11-sean@poorly.run

Cc: Zain Wang <wzz@rock-chips.com>
Cc: Tomasz Figa <tfiga@chromium.org>
Cc: Kristian H. Kristensen <hoegsberg@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190611160844.257498-11-sean@poorly.run

drm/rockchip: Use vop_win in vop_win_disable instead of vop_win_data

Change the argument to vop_win_disable to vop_win to accomodate future
changes to the function.

Changes in v4:
- Added to the patchset
Changes in v5:
- None

Link to v4: https://patchwork.freedesktop.org/patch/msgid/20190508160920.144739-10-sean@poorly.run

Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190611160844.257498-10-sean@poorly.run

drm/rockchip: Use the helpers for PSR

Instead of rolling our own implementation for tracking when PSR should
be [in]active, use the new self refresh helpers to do the heavy lifting.

Changes in v2:
- updated to reflect changes made in the helpers
Changes in v3:
- use the new atomic hooks to inspect crtc state instead of needing conn state (Daniel)
Changes in v4:
- Use Laurent's get_new_connector_for_encoder helper (Daniel)
- Exit vop disable early if it's already off
Changes in v5:
- Rebase on latest drm-misc-next
- Resolve conflict with s/edp_vsc_psr/dp_sdp/ rename
- Resolve conflict with drm_atomic.h header inclusion

Link to v1: https://patchwork.freedesktop.org/patch/msgid/20190228210939.83386-4-sean@poorly.run
Link to v2: https://patchwork.freedesktop.org/patch/msgid/20190326204509.96515-3-sean@poorly.run
Link to v3: https://patchwork.freedesktop.org/patch/msgid/20190502194956.218441-9-sean@poorly.run
Link to v4: https://patchwork.freedesktop.org/patch/msgid/20190508160920.144739-9-sean@poorly.run

Cc: Zain Wang <wzz@rock-chips.com>
Cc: Tomasz Figa <tfiga@chromium.org>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
[seanpaul resolved some conflicts with drmP.h work and Helen's async fixes]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190611160844.257498-9-sean@poorly.run

drm/rockchip: Check for fast link training before enabling psr

Once we start shutting off the link during PSR, we're going to want fast
training to work. If the display doesn't support fast training, don't
enable psr.

Changes in v2:
- None
Changes in v3:
- None
Changes in v4:
- None
Changes in v5:
- None

Link to v1: https://patchwork.freedesktop.org/patch/msgid/20190228210939.83386-3-sean@poorly.run
Link to v2: https://patchwork.freedesktop.org/patch/msgid/20190326204509.96515-2-sean@poorly.run
Link to v3: https://patchwork.freedesktop.org/patch/msgid/20190502194956.218441-9-sean@poorly.run
Link to v4: https://patchwork.freedesktop.org/patch/msgid/20190508160920.144739-8-sean@poorly.run

Cc: Zain Wang <wzz@rock-chips.com>
Cc: Tomasz Figa <tfiga@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190611160844.257498-8-sean@poorly.run

drm/panel: jh057n00900: Use drm_panel_{unprepare, disable} consistently

We were already using the generic functions in our debugfs code, do the
same in jh057n_shutdown. This was suggested by Sam Ravnborg.

Signed-off-by: Guido Günther <agx@sigxcpu.org>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/a37dd5083462064f437ff62fd84e6576d8a7c8dc.1564146727.git.agx@sigxcpu.org

drm/panel: jh057n00900: Print error code on all DRM_DEV_ERROR()s

Most of them had these already but two mere missing. This eases
debugging.

Signed-off-by: Guido Günther <agx@sigxcpu.org>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/6b237a570cb368dc4471fb8feb3a0441813cd576.1564146727.git.agx@sigxcpu.org

drm/panel: jh057n00900: Move mipi_dsi_dcs_set_display_off to disable()

This makes it symmetric with the panel init happening in enable().

Signed-off-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/e2c31d34ce1f917065d590297e5115a4ca954874.1564146727.git.agx@sigxcpu.org

drm/panel: jh057n00900: Move panel DSI init to enable()

If the panel is wrapped in a panel_bridge it gets prepar()ed before the
upstream DSI bridge which can cause hangs (e.g. with imx-nwl since clocks
are not enabled yet). To avoid this move the panel's first DSI access to
enable() so the upstream bridge can prepare the DSI host controller in
it's pre_enable().

This is also in line with other panel drivers.

Signed-off-by: Guido Günther <agx@sigxcpu.org>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/12c3495b234952aafe11980a9e06cfd246134660.1564146727.git.agx@sigxcpu.org