Suraj Jitindar Singh [Fri, 21 Dec 2018 03:28:39 +0000 (14:28 +1100)]
KVM: PPC: Book3S HV: Hold kvm->mmu_lock across updating nested pte rc bits
We already hold the kvm->mmu_lock spin lock across updating the rc bits
in the pte for the L1 guest. Continue to hold the lock across updating
the rc bits in the pte for the nested guest as well to prevent
invalidations from occurring.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Suraj Jitindar Singh [Fri, 14 Dec 2018 05:29:10 +0000 (16:29 +1100)]
KVM: PPC: Book3S HV: Allow passthrough of an emulated device to an L3 guest
Previously when a device was being emulated by an L1 guest for an L2
guest, that device couldn't then be passed through to an L3 guest. This
was because the L1 guest had no method for accessing L3 memory.
The hcall H_COPY_TOFROM_GUEST provides this access. Thus this setup for
passthrough can now be allowed.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Suraj Jitindar Singh [Fri, 14 Dec 2018 05:29:09 +0000 (16:29 +1100)]
KVM: PPC: Book3S: Introduce new hcall H_COPY_TOFROM_GUEST to access quadrants 1 & 2
A guest cannot access quadrants 1 or 2 as this would result in an
exception. Thus introduce the hcall H_COPY_TOFROM_GUEST to be used by a
guest when it wants to perform an access to quadrants 1 or 2, for
example when it wants to access memory for one of its nested guests.
Also provide an implementation for the kvm-hv module.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Suraj Jitindar Singh [Fri, 14 Dec 2018 05:29:08 +0000 (16:29 +1100)]
KVM: PPC: Book3S HV: Allow passthrough of an emulated device to an L2 guest
Allow for a device which is being emulated at L0 (the host) for an L1
guest to be passed through to a nested (L2) guest.
The existing kvmppc_hv_emulate_mmio function can be used here. The main
challenge is that for a load the result must be stored into the L2 gpr,
not an L1 gpr as would normally be the case after going out to qemu to
complete the operation. This presents a challenge as at this point the
L2 gpr state has been written back into L1 memory.
To work around this we store the address in L1 memory of the L2 gpr
where the result of the load is to be stored and use the new io_gpr
value KVM_MMIO_REG_NESTED_GPR to indicate that this is a nested load for
which completion must be done when returning back into the kernel. Then
in kvmppc_complete_mmio_load() the resultant value is written into L1
memory at the location of the indicated L2 gpr.
Note that we don't currently let an L1 guest emulate a device for an L2
guest which is then passed through to an L3 guest.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Suraj Jitindar Singh [Fri, 14 Dec 2018 05:29:07 +0000 (16:29 +1100)]
KVM: PPC: Update kvmppc_st and kvmppc_ld to use quadrants
The functions kvmppc_st and kvmppc_ld are used to access guest memory
from the host using a guest effective address. They do so by translating
through the process table to obtain a guest real address and then using
kvm_read_guest or kvm_write_guest to make the access with the guest real
address.
This method of access however only works for L1 guests and will give the
incorrect results for a nested guest.
We can however use the store_to_eaddr and load_from_eaddr kvmppc_ops to
perform the access for a nested guesti (and a L1 guest). So attempt this
method first and fall back to the old method if this fails and we aren't
running a nested guest.
At this stage there is no fall back method to perform the access for a
nested guest and this is left as a future improvement. For now we will
return to the nested guest and rely on the fact that a translation
should be faulted in before retrying the access.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Suraj Jitindar Singh [Fri, 14 Dec 2018 05:29:06 +0000 (16:29 +1100)]
KVM: PPC: Add load_from_eaddr and store_to_eaddr to the kvmppc_ops struct
The kvmppc_ops struct is used to store function pointers to kvm
implementation specific functions.
Introduce two new functions load_from_eaddr and store_to_eaddr to be
used to load from and store to a guest effective address respectively.
Also implement these for the kvm-hv module. If we are using the radix
mmu then we can call the functions to access quadrant 1 and 2.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Suraj Jitindar Singh [Fri, 14 Dec 2018 05:29:05 +0000 (16:29 +1100)]
KVM: PPC: Book3S HV: Implement functions to access quadrants 1 & 2
The POWER9 radix mmu has the concept of quadrants. The quadrant number
is the two high bits of the effective address and determines the fully
qualified address to be used for the translation. The fully qualified
address consists of the effective lpid, the effective pid and the
effective address. This gives then 4 possible quadrants 0, 1, 2, and 3.
When accessing these quadrants the fully qualified address is obtained
as follows:
Quadrant | Hypervisor | Guest
--------------------------------------------------------------------------
| EA[0:1] = 0b00 | EA[0:1] = 0b00
0 | effLPID = 0 | effLPID = LPIDR
| effPID = PIDR | effPID = PIDR
--------------------------------------------------------------------------
| EA[0:1] = 0b01 |
1 | effLPID = LPIDR | Invalid Access
| effPID = PIDR |
--------------------------------------------------------------------------
| EA[0:1] = 0b10 |
2 | effLPID = LPIDR | Invalid Access
| effPID = 0 |
--------------------------------------------------------------------------
| EA[0:1] = 0b11 | EA[0:1] = 0b11
3 | effLPID = 0 | effLPID = LPIDR
| effPID = 0 | effPID = 0
--------------------------------------------------------------------------
In the Guest;
Quadrant 3 is normally used to address the operating system since this
uses effPID=0 and effLPID=LPIDR, meaning the PID register doesn't need to
be switched.
Quadrant 0 is normally used to address user space since the effLPID and
effPID are taken from the corresponding registers.
In the Host;
Quadrant 0 and 3 are used as above, however the effLPID is always 0 to
address the host.
Quadrants 1 and 2 can be used by the host to address guest memory using
a guest effective address. Since the effLPID comes from the LPID register,
the host loads the LPID of the guest it would like to access (and the
PID of the process) and can perform accesses to a guest effective
address.
This means quadrant 1 can be used to address the guest user space and
quadrant 2 can be used to address the guest operating system from the
hypervisor, using a guest effective address.
Access to the quadrants can cause a Hypervisor Data Storage Interrupt
(HDSI) due to being unable to perform partition scoped translation.
Previously this could only be generated from a guest and so the code
path expects us to take the KVM trampoline in the interrupt handler.
This is no longer the case so we modify the handler to call
bad_page_fault() to check if we were expecting this fault so we can
handle it gracefully and just return with an error code. In the hash mmu
case we still raise an unknown exception since quadrants aren't defined
for the hash mmu.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Suraj Jitindar Singh [Fri, 14 Dec 2018 05:29:04 +0000 (16:29 +1100)]
KVM: PPC: Book3S HV: Add function kvmhv_vcpu_is_radix()
There exists a function kvm_is_radix() which is used to determine if a
kvm instance is using the radix mmu. However this only applies to the
first level (L1) guest. Add a function kvmhv_vcpu_is_radix() which can
be used to determine if the current execution context of the vcpu is
radix, accounting for if the vcpu is running a nested guest.
Currently all nested guests must be radix but this may change in the
future.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Suraj Jitindar Singh [Fri, 14 Dec 2018 05:29:03 +0000 (16:29 +1100)]
KVM: PPC: Book3S: Only report KVM_CAP_SPAPR_TCE_VFIO on powernv machines
The kvm capability KVM_CAP_SPAPR_TCE_VFIO is used to indicate the
availability of in kernel tce acceleration for vfio. However it is
currently the case that this is only available on a powernv machine,
not for a pseries machine.
Thus make this capability dependent on having the cpu feature
CPU_FTR_HVMODE.
[paulus@ozlabs.org - fixed compilation for Book E.]
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Paul Mackerras [Wed, 12 Dec 2018 04:17:17 +0000 (15:17 +1100)]
KVM: PPC: Book3S HV: Flush guest mappings when turning dirty tracking on/off
This adds code to flush the partition-scoped page tables for a radix
guest when dirty tracking is turned on or off for a memslot. Only the
guest real addresses covered by the memslot are flushed. The reason
for this is to get rid of any 2M PTEs in the partition-scoped page
tables that correspond to host transparent huge pages, so that page
dirtiness is tracked at a system page (4k or 64k) granularity rather
than a 2M granularity. The page tables are also flushed when turning
dirty tracking off so that the memslot's address space can be
repopulated with THPs if possible.
To do this, we add a new function kvmppc_radix_flush_memslot(). Since
this does what's needed for kvmppc_core_flush_memslot_hv() on a radix
guest, we now make kvmppc_core_flush_memslot_hv() call the new
kvmppc_radix_flush_memslot() rather than calling kvm_unmap_radix()
for each page in the memslot. This has the effect of fixing a bug in
that kvmppc_core_flush_memslot_hv() was previously calling
kvm_unmap_radix() without holding the kvm->mmu_lock spinlock, which
is required to be held.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Reviewed-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Paul Mackerras [Wed, 12 Dec 2018 04:16:48 +0000 (15:16 +1100)]
KVM: PPC: Book3S HV: Cleanups - constify memslots, fix comments
This adds 'const' to the declarations for the struct kvm_memory_slot
pointer parameters of some functions, which will make it possible to
call those functions from kvmppc_core_commit_memory_region_hv()
in the next patch.
This also fixes some comments about locking.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Reviewed-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Paul Mackerras [Wed, 12 Dec 2018 04:16:17 +0000 (15:16 +1100)]
KVM: PPC: Book3S HV: Map single pages when doing dirty page logging
For radix guests, this makes KVM map guest memory as individual pages
when dirty page logging is enabled for the memslot corresponding to the
guest real address. Having a separate partition-scoped PTE for each
system page mapped to the guest means that we have a separate dirty
bit for each page, thus making the reported dirty bitmap more accurate.
Without this, if part of guest memory is backed by transparent huge
pages, the dirty status is reported at a 2MB granularity rather than
a 64kB (or 4kB) granularity for that part, causing userspace to have
to transmit more data when migrating the guest.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Reviewed-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Bharata B Rao [Wed, 12 Dec 2018 04:15:30 +0000 (15:15 +1100)]
KVM: PPC: Pass change type down to memslot commit function
Currently, kvm_arch_commit_memory_region() gets called with a
parameter indicating what type of change is being made to the memslot,
but it doesn't pass it down to the platform-specific memslot commit
functions. This adds the `change' parameter to the lower-level
functions so that they can use it in future.
[paulus@ozlabs.org - fix book E also.]
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Reviewed-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Suraj Jitindar Singh [Fri, 7 Dec 2018 01:17:03 +0000 (12:17 +1100)]
KVM: PPC: Book3S PR: Set hflag to indicate that POWER9 supports 1T segments
When booting a kvm-pr guest on a POWER9 machine the following message is
observed:
"qemu-system-ppc64: KVM does not support 1TiB segments which guest expects"
This is because the guest is expecting to be able to use 1T segments
however we don't indicate support for it. This is because we don't set
the BOOK3S_HFLAG_MULTI_PGSIZE flag in the hflags in kvmppc_set_pvr_pr()
on POWER9.
POWER9 does indeed have support for 1T segments, so add a case for
POWER9 to the switch statement to ensure it is set.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Yangtao Li [Mon, 5 Nov 2018 14:47:17 +0000 (09:47 -0500)]
KVM: PPC: Book3S HV: Change to use DEFINE_SHOW_ATTRIBUTE macro
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Paul Mackerras [Fri, 16 Nov 2018 10:28:18 +0000 (21:28 +1100)]
KVM: PPC: Book3S HV: Fix race between kvm_unmap_hva_range and MMU mode switch
Testing has revealed an occasional crash which appears to be caused
by a race between kvmppc_switch_mmu_to_hpt and kvm_unmap_hva_range_hv.
The symptom is a NULL pointer dereference in __find_linux_pte() called
from kvm_unmap_radix() with kvm->arch.pgtable == NULL.
Looking at kvmppc_switch_mmu_to_hpt(), it does indeed clear
kvm->arch.pgtable (via kvmppc_free_radix()) before setting
kvm->arch.radix to NULL, and there is nothing to prevent
kvm_unmap_hva_range_hv() or the other MMU callback functions from
being called concurrently with kvmppc_switch_mmu_to_hpt() or
kvmppc_switch_mmu_to_radix().
This patch therefore adds calls to spin_lock/unlock on the kvm->mmu_lock
around the assignments to kvm->arch.radix, and makes sure that the
partition-scoped radix tree or HPT is only freed after changing
kvm->arch.radix.
This also takes the kvm->mmu_lock in kvmppc_rmap_reset() to make sure
that the clearing of each rmap array (one per memslot) doesn't happen
concurrently with use of the array in the kvm_unmap_hva_range_hv()
or the other MMU callbacks.
Fixes: 18c3640cefc7 ("KVM: PPC: Book3S HV: Add infrastructure for running HPT guests on radix host")
Cc: stable@vger.kernel.org # v4.15+
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Jim Mattson [Tue, 22 May 2018 16:54:20 +0000 (09:54 -0700)]
kvm: svm: Ensure an IBPB on all affected CPUs when freeing a vmcb
Previously, we only called indirect_branch_prediction_barrier on the
logical CPU that freed a vmcb. This function should be called on all
logical CPUs that last loaded the vmcb in question.
Fixes: 15d45071523d ("KVM/x86: Add IBPB support")
Reported-by: Neel Natu <neelnatu@google.com>
Signed-off-by: Jim Mattson <jmattson@google.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Junaid Shahid [Wed, 31 Oct 2018 21:53:57 +0000 (14:53 -0700)]
kvm: mmu: Fix race in emulated page table writes
When a guest page table is updated via an emulated write,
kvm_mmu_pte_write() is called to update the shadow PTE using the just
written guest PTE value. But if two emulated guest PTE writes happened
concurrently, it is possible that the guest PTE and the shadow PTE end
up being out of sync. Emulated writes do not mark the shadow page as
unsync-ed, so this inconsistency will not be resolved even by a guest TLB
flush (unless the page was marked as unsync-ed at some other point).
This is fixed by re-reading the current value of the guest PTE after the
MMU lock has been acquired instead of just using the value that was
written prior to calling kvm_mmu_pte_write().
Signed-off-by: Junaid Shahid <junaids@google.com>
Reviewed-by: Wanpeng Li <wanpengli@tencent.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Liran Alon [Tue, 13 Nov 2018 15:44:46 +0000 (17:44 +0200)]
KVM: nVMX: vmcs12 revision_id is always VMCS12_REVISION even when copied from eVMCS
vmcs12 represents the per-CPU cache of L1 active vmcs12.
This cache can be loaded by one of the following:
1) Guest making a vmcs12 active by exeucting VMPTRLD
2) Guest specifying eVMCS in VP assist page and executing
VMLAUNCH/VMRESUME.
Either way, vmcs12 should have revision_id of VMCS12_REVISION.
Which is not equal to eVMCS revision_id which specifies used
VersionNumber of eVMCS struct (e.g. KVM_EVMCS_VERSION).
Specifically, this causes an issue in restoring a nested VM state
because vmx_set_nested_state() verifies that vmcs12->revision_id
is equal to VMCS12_REVISION which was not true in case vmcs12
was populated from an eVMCS by vmx_get_nested_state() which calls
copy_enlightened_to_vmcs12().
Reviewed-by: Darren Kenny <darren.kenny@oracle.com>
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Liran Alon [Thu, 1 Nov 2018 08:57:39 +0000 (10:57 +0200)]
KVM: nVMX: Verify eVMCS revision id match supported eVMCS version on eVMCS VMPTRLD
According to TLFS section 16.11.2 Enlightened VMCS, the first u32
field of eVMCS should specify eVMCS VersionNumber.
This version should be in the range of supported eVMCS versions exposed
to guest via CPUID.0x4000000A.EAX[0:15].
The range which KVM expose to guest in this CPUID field should be the
same as the value returned in vmcs_version by nested_enable_evmcs().
According to the above, eVMCS VMPTRLD should verify that version specified
in given eVMCS is in the supported range. However, current code
mistakenly verfies this field against VMCS12_REVISION.
One can also see that when KVM use eVMCS, it makes sure that
alloc_vmcs_cpu() sets allocated eVMCS revision_id to KVM_EVMCS_VERSION.
Obvious fix should just change eVMCS VMPTRLD to verify first u32 field
of eVMCS is equal to KVM_EVMCS_VERSION.
However, it turns out that Microsoft Hyper-V fails to comply to their
own invented interface: When Hyper-V use eVMCS, it just sets first u32
field of eVMCS to revision_id specified in MSR_IA32_VMX_BASIC (In our
case: VMCS12_REVISION). Instead of used eVMCS version number which is
one of the supported versions specified in CPUID.0x4000000A.EAX[0:15].
To overcome Hyper-V bug, we accept either a supported eVMCS version
or VMCS12_REVISION as valid values for first u32 field of eVMCS.
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Nikita Leshenko <nikita.leshchenko@oracle.com>
Reviewed-by: Mark Kanda <mark.kanda@oracle.com>
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Leonid Shatz [Tue, 6 Nov 2018 10:14:25 +0000 (12:14 +0200)]
KVM: nVMX/nSVM: Fix bug which sets vcpu->arch.tsc_offset to L1 tsc_offset
Since commit
e79f245ddec1 ("X86/KVM: Properly update 'tsc_offset' to
represent the running guest"), vcpu->arch.tsc_offset meaning was
changed to always reflect the tsc_offset value set on active VMCS.
Regardless if vCPU is currently running L1 or L2.
However, above mentioned commit failed to also change
kvm_vcpu_write_tsc_offset() to set vcpu->arch.tsc_offset correctly.
This is because vmx_write_tsc_offset() could set the tsc_offset value
in active VMCS to given offset parameter *plus vmcs12->tsc_offset*.
However, kvm_vcpu_write_tsc_offset() just sets vcpu->arch.tsc_offset
to given offset parameter. Without taking into account the possible
addition of vmcs12->tsc_offset. (Same is true for SVM case).
Fix this issue by changing kvm_x86_ops->write_tsc_offset() to return
actually set tsc_offset in active VMCS and modify
kvm_vcpu_write_tsc_offset() to set returned value in
vcpu->arch.tsc_offset.
In addition, rename write_tsc_offset() callback to write_l1_tsc_offset()
to make it clear that it is meant to set L1 TSC offset.
Fixes: e79f245ddec1 ("X86/KVM: Properly update 'tsc_offset' to represent the running guest")
Reviewed-by: Liran Alon <liran.alon@oracle.com>
Reviewed-by: Mihai Carabas <mihai.carabas@oracle.com>
Reviewed-by: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Signed-off-by: Leonid Shatz <leonid.shatz@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Yi Wang [Thu, 8 Nov 2018 03:22:21 +0000 (11:22 +0800)]
x86/kvm/vmx: fix old-style function declaration
The inline keyword which is not at the beginning of the function
declaration may trigger the following build warnings, so let's fix it:
arch/x86/kvm/vmx.c:1309:1: warning: ‘inline’ is not at beginning of declaration [-Wold-style-declaration]
arch/x86/kvm/vmx.c:5947:1: warning: ‘inline’ is not at beginning of declaration [-Wold-style-declaration]
arch/x86/kvm/vmx.c:5985:1: warning: ‘inline’ is not at beginning of declaration [-Wold-style-declaration]
arch/x86/kvm/vmx.c:6023:1: warning: ‘inline’ is not at beginning of declaration [-Wold-style-declaration]
Signed-off-by: Yi Wang <wang.yi59@zte.com.cn>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Yi Wang [Thu, 8 Nov 2018 08:48:36 +0000 (16:48 +0800)]
KVM: x86: fix empty-body warnings
We get the following warnings about empty statements when building
with 'W=1':
arch/x86/kvm/lapic.c:632:53: warning: suggest braces around empty body in an ‘if’ statement [-Wempty-body]
arch/x86/kvm/lapic.c:1907:42: warning: suggest braces around empty body in an ‘if’ statement [-Wempty-body]
arch/x86/kvm/lapic.c:1936:65: warning: suggest braces around empty body in an ‘if’ statement [-Wempty-body]
arch/x86/kvm/lapic.c:1975:44: warning: suggest braces around empty body in an ‘if’ statement [-Wempty-body]
Rework the debug helper macro to get rid of these warnings.
Signed-off-by: Yi Wang <wang.yi59@zte.com.cn>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Liran Alon [Tue, 20 Nov 2018 16:03:25 +0000 (18:03 +0200)]
KVM: VMX: Update shared MSRs to be saved/restored on MSR_EFER.LMA changes
When guest transitions from/to long-mode by modifying MSR_EFER.LMA,
the list of shared MSRs to be saved/restored on guest<->host
transitions is updated (See vmx_set_efer() call to setup_msrs()).
On every entry to guest, vcpu_enter_guest() calls
vmx_prepare_switch_to_guest(). This function should also take care
of setting the shared MSRs to be saved/restored. However, the
function does nothing in case we are already running with loaded
guest state (vmx->loaded_cpu_state != NULL).
This means that even when guest modifies MSR_EFER.LMA which results
in updating the list of shared MSRs, it isn't being taken into account
by vmx_prepare_switch_to_guest() because it happens while we are
running with loaded guest state.
To fix above mentioned issue, add a flag to mark that the list of
shared MSRs has been updated and modify vmx_prepare_switch_to_guest()
to set shared MSRs when running with host state *OR* list of shared
MSRs has been updated.
Note that this issue was mistakenly introduced by commit
678e315e78a7 ("KVM: vmx: add dedicated utility to access guest's
kernel_gs_base") because previously vmx_set_efer() always called
vmx_load_host_state() which resulted in vmx_prepare_switch_to_guest() to
set shared MSRs.
Fixes: 678e315e78a7 ("KVM: vmx: add dedicated utility to access guest's kernel_gs_base")
Reported-by: Eyal Moscovici <eyal.moscovici@oracle.com>
Reviewed-by: Mihai Carabas <mihai.carabas@oracle.com>
Reviewed-by: Liam Merwick <liam.merwick@oracle.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Liran Alon [Wed, 7 Nov 2018 22:43:06 +0000 (00:43 +0200)]
KVM: x86: Fix kernel info-leak in KVM_HC_CLOCK_PAIRING hypercall
kvm_pv_clock_pairing() allocates local var
"struct kvm_clock_pairing clock_pairing" on stack and initializes
all it's fields besides padding (clock_pairing.pad[]).
Because clock_pairing var is written completely (including padding)
to guest memory, failure to init struct padding results in kernel
info-leak.
Fix the issue by making sure to also init the padding with zeroes.
Fixes: 55dd00a73a51 ("KVM: x86: add KVM_HC_CLOCK_PAIRING hypercall")
Reported-by: syzbot+a8ef68d71211ba264f56@syzkaller.appspotmail.com
Reviewed-by: Mark Kanda <mark.kanda@oracle.com>
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Liran Alon [Sat, 17 Nov 2018 12:05:06 +0000 (14:05 +0200)]
KVM: nVMX: Fix kernel info-leak when enabling KVM_CAP_HYPERV_ENLIGHTENED_VMCS more than once
Consider the case that userspace enables KVM_CAP_HYPERV_ENLIGHTENED_VMCS twice:
1) kvm_vcpu_ioctl_enable_cap() is called to enable
KVM_CAP_HYPERV_ENLIGHTENED_VMCS which calls nested_enable_evmcs().
2) nested_enable_evmcs() sets enlightened_vmcs_enabled to true and fills
vmcs_version which is then copied to userspace.
3) kvm_vcpu_ioctl_enable_cap() is called again to enable
KVM_CAP_HYPERV_ENLIGHTENED_VMCS which calls nested_enable_evmcs().
4) This time nested_enable_evmcs() just returns 0 as
enlightened_vmcs_enabled is already true. *Without filling
vmcs_version*.
5) kvm_vcpu_ioctl_enable_cap() continues as usual and copies
*uninitialized* vmcs_version to userspace which leads to kernel info-leak.
Fix this issue by simply changing nested_enable_evmcs() to always fill
vmcs_version output argument. Even when enlightened_vmcs_enabled is
already set to true.
Note that SVM's nested_enable_evmcs() should not be modified because it
always returns a non-zero value (-ENODEV) which results in
kvm_vcpu_ioctl_enable_cap() skipping the copy of vmcs_version to
userspace (as it should).
Fixes: 57b119da3594 ("KVM: nVMX: add KVM_CAP_HYPERV_ENLIGHTENED_VMCS capability")
Reported-by: syzbot+cfbc368e283d381f8cef@syzkaller.appspotmail.com
Reviewed-by: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Wei Wang [Mon, 12 Nov 2018 12:23:14 +0000 (12:23 +0000)]
svm: Add mutex_lock to protect apic_access_page_done on AMD systems
There is a race condition when accessing kvm->arch.apic_access_page_done.
Due to it, x86_set_memory_region will fail when creating the second vcpu
for a svm guest.
Add a mutex_lock to serialize the accesses to apic_access_page_done.
This lock is also used by vmx for the same purpose.
Signed-off-by: Wei Wang <wawei@amazon.de>
Signed-off-by: Amadeusz Juskowiak <ajusk@amazon.de>
Signed-off-by: Julian Stecklina <jsteckli@amazon.de>
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Wanpeng Li [Tue, 20 Nov 2018 08:34:18 +0000 (16:34 +0800)]
KVM: X86: Fix scan ioapic use-before-initialization
Reported by syzkaller:
BUG: unable to handle kernel NULL pointer dereference at
00000000000001c8
PGD
80000003ec4da067 P4D
80000003ec4da067 PUD
3f7bfa067 PMD 0
Oops: 0000 [#1] PREEMPT SMP PTI
CPU: 7 PID: 5059 Comm: debug Tainted: G OE 4.19.0-rc5 #16
RIP: 0010:__lock_acquire+0x1a6/0x1990
Call Trace:
lock_acquire+0xdb/0x210
_raw_spin_lock+0x38/0x70
kvm_ioapic_scan_entry+0x3e/0x110 [kvm]
vcpu_enter_guest+0x167e/0x1910 [kvm]
kvm_arch_vcpu_ioctl_run+0x35c/0x610 [kvm]
kvm_vcpu_ioctl+0x3e9/0x6d0 [kvm]
do_vfs_ioctl+0xa5/0x690
ksys_ioctl+0x6d/0x80
__x64_sys_ioctl+0x1a/0x20
do_syscall_64+0x83/0x6e0
entry_SYSCALL_64_after_hwframe+0x49/0xbe
The reason is that the testcase writes hyperv synic HV_X64_MSR_SINT6 msr
and triggers scan ioapic logic to load synic vectors into EOI exit bitmap.
However, irqchip is not initialized by this simple testcase, ioapic/apic
objects should not be accessed.
This can be triggered by the following program:
#define _GNU_SOURCE
#include <endian.h>
#include <stdint.h>
#include <stdio.h>
#include <stdlib.h>
#include <string.h>
#include <sys/syscall.h>
#include <sys/types.h>
#include <unistd.h>
uint64_t r[3] = {0xffffffffffffffff, 0xffffffffffffffff, 0xffffffffffffffff};
int main(void)
{
syscall(__NR_mmap, 0x20000000, 0x1000000, 3, 0x32, -1, 0);
long res = 0;
memcpy((void*)0x20000040, "/dev/kvm", 9);
res = syscall(__NR_openat, 0xffffffffffffff9c, 0x20000040, 0, 0);
if (res != -1)
r[0] = res;
res = syscall(__NR_ioctl, r[0], 0xae01, 0);
if (res != -1)
r[1] = res;
res = syscall(__NR_ioctl, r[1], 0xae41, 0);
if (res != -1)
r[2] = res;
memcpy(
(void*)0x20000080,
"\x01\x00\x00\x00\x00\x5b\x61\xbb\x96\x00\x00\x40\x00\x00\x00\x00\x01\x00"
"\x08\x00\x00\x00\x00\x00\x0b\x77\xd1\x78\x4d\xd8\x3a\xed\xb1\x5c\x2e\x43"
"\xaa\x43\x39\xd6\xff\xf5\xf0\xa8\x98\xf2\x3e\x37\x29\x89\xde\x88\xc6\x33"
"\xfc\x2a\xdb\xb7\xe1\x4c\xac\x28\x61\x7b\x9c\xa9\xbc\x0d\xa0\x63\xfe\xfe"
"\xe8\x75\xde\xdd\x19\x38\xdc\x34\xf5\xec\x05\xfd\xeb\x5d\xed\x2e\xaf\x22"
"\xfa\xab\xb7\xe4\x42\x67\xd0\xaf\x06\x1c\x6a\x35\x67\x10\x55\xcb",
106);
syscall(__NR_ioctl, r[2], 0x4008ae89, 0x20000080);
syscall(__NR_ioctl, r[2], 0xae80, 0);
return 0;
}
This patch fixes it by bailing out scan ioapic if ioapic is not initialized in
kernel.
Reported-by: Wei Wu <ww9210@gmail.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Wei Wu <ww9210@gmail.com>
Signed-off-by: Wanpeng Li <wanpengli@tencent.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Wanpeng Li [Tue, 20 Nov 2018 01:39:30 +0000 (09:39 +0800)]
KVM: LAPIC: Fix pv ipis use-before-initialization
Reported by syzkaller:
BUG: unable to handle kernel NULL pointer dereference at
0000000000000014
PGD
800000040410c067 P4D
800000040410c067 PUD
40410d067 PMD 0
Oops: 0000 [#1] PREEMPT SMP PTI
CPU: 3 PID: 2567 Comm: poc Tainted: G OE 4.19.0-rc5 #16
RIP: 0010:kvm_pv_send_ipi+0x94/0x350 [kvm]
Call Trace:
kvm_emulate_hypercall+0x3cc/0x700 [kvm]
handle_vmcall+0xe/0x10 [kvm_intel]
vmx_handle_exit+0xc1/0x11b0 [kvm_intel]
vcpu_enter_guest+0x9fb/0x1910 [kvm]
kvm_arch_vcpu_ioctl_run+0x35c/0x610 [kvm]
kvm_vcpu_ioctl+0x3e9/0x6d0 [kvm]
do_vfs_ioctl+0xa5/0x690
ksys_ioctl+0x6d/0x80
__x64_sys_ioctl+0x1a/0x20
do_syscall_64+0x83/0x6e0
entry_SYSCALL_64_after_hwframe+0x49/0xbe
The reason is that the apic map has not yet been initialized, the testcase
triggers pv_send_ipi interface by vmcall which results in kvm->arch.apic_map
is dereferenced. This patch fixes it by checking whether or not apic map is
NULL and bailing out immediately if that is the case.
Fixes: 4180bf1b65 (KVM: X86: Implement "send IPI" hypercall)
Reported-by: Wei Wu <ww9210@gmail.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Wei Wu <ww9210@gmail.com>
Signed-off-by: Wanpeng Li <wanpengli@tencent.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Luiz Capitulino [Fri, 23 Nov 2018 17:02:14 +0000 (12:02 -0500)]
KVM: VMX: re-add ple_gap module parameter
Apparently, the ple_gap parameter was accidentally removed
by commit
c8e88717cfc6b36bedea22368d97667446318291. Add it
back.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Cc: stable@vger.kernel.org
Fixes: c8e88717cfc6b36bedea22368d97667446318291
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Paolo Bonzini [Sun, 25 Nov 2018 17:56:32 +0000 (18:56 +0100)]
Merge tag 'kvm-ppc-fixes-4.20-1' of https://git./linux/kernel/git/paulus/powerpc into HEAD
PPC KVM fixes for 4.20
This has a single 1-line patch which fixes a bug in the recently-merged
nested HV KVM support.
Linus Torvalds [Sun, 18 Nov 2018 21:33:44 +0000 (13:33 -0800)]
Linux 4.20-rc3
Linus Torvalds [Sun, 18 Nov 2018 20:21:09 +0000 (12:21 -0800)]
Merge tag 'libnvdimm-fixes-4.20-rc3' of git://git./linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dan Williams:
"A small batch of fixes for v4.20-rc3.
The overflow continuation fix addresses something that has been broken
for several releases. Arguably it could wait even longer, but it's a
one line fix and this finishes the last of the known address range
scrub bug reports. The revert addresses a lockdep regression. The unit
tests are not critical to fix, but no reason to hold this fix back.
Summary:
- Address Range Scrub overflow continuation handling has been broken
since it was initially merged. It was only recently that error
injection and platform-BIOS support enabled this corner case to be
exercised.
- The recent attempt to provide more isolation for the kernel Address
Range Scrub state machine from userapace initiated sessions
triggers a lockdep report. Revert and try again at the next merge
window.
- Fix a kasan reported buffer overflow in libnvdimm unit test
infrastrucutre (nfit_test)"
* tag 'libnvdimm-fixes-4.20-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
Revert "acpi, nfit: Further restrict userspace ARS start requests"
acpi, nfit: Fix ARS overflow continuation
tools/testing/nvdimm: Fix the array size for dimm devices.
Linus Torvalds [Sun, 18 Nov 2018 19:31:26 +0000 (11:31 -0800)]
Merge branch 'akpm' (patches from Andrew)
Merge misc fixes from Andrew Morton:
"16 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm/memblock.c: fix a typo in __next_mem_pfn_range() comments
mm, page_alloc: check for max order in hot path
scripts/spdxcheck.py: make python3 compliant
tmpfs: make lseek(SEEK_DATA/SEK_HOLE) return ENXIO with a negative offset
lib/ubsan.c: don't mark __ubsan_handle_builtin_unreachable as noreturn
mm/vmstat.c: fix NUMA statistics updates
mm/gup.c: fix follow_page_mask() kerneldoc comment
ocfs2: free up write context when direct IO failed
scripts/faddr2line: fix location of start_kernel in comment
mm: don't reclaim inodes with many attached pages
mm, memory_hotplug: check zone_movable in has_unmovable_pages
mm/swapfile.c: use kvzalloc for swap_info_struct allocation
MAINTAINERS: update OMAP MMC entry
hugetlbfs: fix kernel BUG at fs/hugetlbfs/inode.c:444!
kernel/sched/psi.c: simplify cgroup_move_task()
z3fold: fix possible reclaim races
Linus Torvalds [Sun, 18 Nov 2018 18:58:20 +0000 (10:58 -0800)]
Merge branch 'sched-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull scheduler fix from Ingo Molnar:
"Fix an exec() related scalability/performance regression, which was
caused by incorrectly calculating load and migrating tasks on exec()
when they shouldn't be"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/fair: Fix cpu_util_wake() for 'execl' type workloads
Linus Torvalds [Sun, 18 Nov 2018 18:54:59 +0000 (10:54 -0800)]
Merge branch 'perf-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Fix uncore PMU enumeration for CofeeLake CPUs"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel/uncore: Support CoffeeLake 8th CBOX
perf/x86/intel/uncore: Add more IMC PCI IDs for KabyLake and CoffeeLake CPUs
Linus Torvalds [Sun, 18 Nov 2018 18:52:26 +0000 (10:52 -0800)]
Merge branch 'efi-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull EFI fixes from Ingo Molnar:
"Misc fixes: two warning splat fixes, a leak fix and persistent memory
allocation fixes for ARM"
* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi: Permit calling efi_mem_reserve_persistent() from atomic context
efi/arm: Defer persistent reservations until after paging_init()
efi/arm/libstub: Pack FDT after populating it
efi/arm: Revert deferred unmap of early memmap mapping
efi: Fix debugobjects warning on 'efi_rts_work'
Linus Torvalds [Sun, 18 Nov 2018 18:45:09 +0000 (10:45 -0800)]
Merge branch 'spectre' of git://git.armlinux.org.uk/~rmk/linux-arm
Pull ARM spectre updates from Russell King:
"These are the currently known final bits that resolve the Spectre
issues. big.Little systems used to be sufficiently identical in that
there were no differences between individual CPUs in the system that
mattered to the kernel. With the advent of the Spectre problem, the
CPUs now have differences in how the workaround is applied.
As a result of previous Spectre patches, these systems ended up
reporting quite a lot of:
"CPUx: Spectre v2: incorrect context switching function, system vulnerable"
messages due to the action of the big.Little switcher causing the CPUs
to be re-initialised regularly. This series resolves that issue by
making the CPU vtable unique to each CPU.
However, since this is used very early, before per-cpu is setup,
per-cpu can't be used. We also have a problem that two of the methods
are not called from preempt-safe paths, but thankfully these remain
identical between all CPUs in the system. To make sure, we validate
that these are identical during boot"
* 'spectre' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: spectre-v2: per-CPU vtables to work around big.Little systems
ARM: add PROC_VTABLE and PROC_TABLE macros
ARM: clean up per-processor check_bugs method call
ARM: split out processor lookup
ARM: make lookup_processor_type() non-__init
Chen Chang [Fri, 16 Nov 2018 23:08:57 +0000 (15:08 -0800)]
mm/memblock.c: fix a typo in __next_mem_pfn_range() comments
Link: http://lkml.kernel.org/r/20181107100247.13359-1-rainccrun@gmail.com
Signed-off-by: Chen Chang <rainccrun@gmail.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Mike Rapoport <rppt@linux.ibm.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michal Hocko [Fri, 16 Nov 2018 23:08:53 +0000 (15:08 -0800)]
mm, page_alloc: check for max order in hot path
Konstantin has noticed that kvmalloc might trigger the following
warning:
WARNING: CPU: 0 PID: 6676 at mm/vmstat.c:986 __fragmentation_index+0x54/0x60
[...]
Call Trace:
fragmentation_index+0x76/0x90
compaction_suitable+0x4f/0xf0
shrink_node+0x295/0x310
node_reclaim+0x205/0x250
get_page_from_freelist+0x649/0xad0
__alloc_pages_nodemask+0x12a/0x2a0
kmalloc_large_node+0x47/0x90
__kmalloc_node+0x22b/0x2e0
kvmalloc_node+0x3e/0x70
xt_alloc_table_info+0x3a/0x80 [x_tables]
do_ip6t_set_ctl+0xcd/0x1c0 [ip6_tables]
nf_setsockopt+0x44/0x60
SyS_setsockopt+0x6f/0xc0
do_syscall_64+0x67/0x120
entry_SYSCALL_64_after_hwframe+0x3d/0xa2
the problem is that we only check for an out of bound order in the slow
path and the node reclaim might happen from the fast path already. This
is fixable by making sure that kvmalloc doesn't ever use kmalloc for
requests that are larger than KMALLOC_MAX_SIZE but this also shows that
the code is rather fragile. A recent UBSAN report just underlines that
by the following report
UBSAN: Undefined behaviour in mm/page_alloc.c:3117:19
shift exponent 51 is too large for 32-bit type 'int'
CPU: 0 PID: 6520 Comm: syz-executor1 Not tainted 4.19.0-rc2 #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0xd2/0x148 lib/dump_stack.c:113
ubsan_epilogue+0x12/0x94 lib/ubsan.c:159
__ubsan_handle_shift_out_of_bounds+0x2b6/0x30b lib/ubsan.c:425
__zone_watermark_ok+0x2c7/0x400 mm/page_alloc.c:3117
zone_watermark_fast mm/page_alloc.c:3216 [inline]
get_page_from_freelist+0xc49/0x44c0 mm/page_alloc.c:3300
__alloc_pages_nodemask+0x21e/0x640 mm/page_alloc.c:4370
alloc_pages_current+0xcc/0x210 mm/mempolicy.c:2093
alloc_pages include/linux/gfp.h:509 [inline]
__get_free_pages+0x12/0x60 mm/page_alloc.c:4414
dma_mem_alloc+0x36/0x50 arch/x86/include/asm/floppy.h:156
raw_cmd_copyin drivers/block/floppy.c:3159 [inline]
raw_cmd_ioctl drivers/block/floppy.c:3206 [inline]
fd_locked_ioctl+0xa00/0x2c10 drivers/block/floppy.c:3544
fd_ioctl+0x40/0x60 drivers/block/floppy.c:3571
__blkdev_driver_ioctl block/ioctl.c:303 [inline]
blkdev_ioctl+0xb3c/0x1a30 block/ioctl.c:601
block_ioctl+0x105/0x150 fs/block_dev.c:1883
vfs_ioctl fs/ioctl.c:46 [inline]
do_vfs_ioctl+0x1c0/0x1150 fs/ioctl.c:687
ksys_ioctl+0x9e/0xb0 fs/ioctl.c:702
__do_sys_ioctl fs/ioctl.c:709 [inline]
__se_sys_ioctl fs/ioctl.c:707 [inline]
__x64_sys_ioctl+0x7e/0xc0 fs/ioctl.c:707
do_syscall_64+0xc4/0x510 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Note that this is not a kvmalloc path. It is just that the fast path
really depends on having sanitzed order as well. Therefore move the
order check to the fast path.
Link: http://lkml.kernel.org/r/20181113094305.GM15120@dhcp22.suse.cz
Signed-off-by: Michal Hocko <mhocko@suse.com>
Reported-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Reported-by: Kyungtae Kim <kt0755@gmail.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Balbir Singh <bsingharora@gmail.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Pavel Tatashin <pavel.tatashin@microsoft.com>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Aaron Lu <aaron.lu@intel.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Byoungyoung Lee <lifeasageek@gmail.com>
Cc: "Dae R. Jeong" <threeearcat@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Uwe Kleine-König [Fri, 16 Nov 2018 23:08:43 +0000 (15:08 -0800)]
scripts/spdxcheck.py: make python3 compliant
Without this change the following happens when using Python3 (3.6.6):
$ echo "GPL-2.0" | python3 scripts/spdxcheck.py -
FAIL: 'str' object has no attribute 'decode'
Traceback (most recent call last):
File "scripts/spdxcheck.py", line 253, in <module>
parser.parse_lines(sys.stdin, args.maxlines, '-')
File "scripts/spdxcheck.py", line 171, in parse_lines
line = line.decode(locale.getpreferredencoding(False), errors='ignore')
AttributeError: 'str' object has no attribute 'decode'
So as the line is already a string, there is no need to decode it and
the line can be dropped.
/usr/bin/python on Arch is Python 3. So this would indeed be worth
going into 4.19.
Link: http://lkml.kernel.org/r/20181023070802.22558-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Joe Perches <joe@perches.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Yufen Yu [Fri, 16 Nov 2018 23:08:39 +0000 (15:08 -0800)]
tmpfs: make lseek(SEEK_DATA/SEK_HOLE) return ENXIO with a negative offset
Other filesystems such as ext4, f2fs and ubifs all return ENXIO when
lseek (SEEK_DATA or SEEK_HOLE) requests a negative offset.
man 2 lseek says
: EINVAL whence is not valid. Or: the resulting file offset would be
: negative, or beyond the end of a seekable device.
:
: ENXIO whence is SEEK_DATA or SEEK_HOLE, and the file offset is beyond
: the end of the file.
Make tmpfs return ENXIO under these circumstances as well. After this,
tmpfs also passes xfstests's generic/448.
[akpm@linux-foundation.org: rewrite changelog]
Link: http://lkml.kernel.org/r/1540434176-14349-1-git-send-email-yuyufen@huawei.com
Signed-off-by: Yufen Yu <yuyufen@huawei.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Hugh Dickins <hughd@google.com>
Cc: William Kucharski <william.kucharski@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Arnd Bergmann [Fri, 16 Nov 2018 23:08:35 +0000 (15:08 -0800)]
lib/ubsan.c: don't mark __ubsan_handle_builtin_unreachable as noreturn
gcc-8 complains about the prototype for this function:
lib/ubsan.c:432:1: error: ignoring attribute 'noreturn' in declaration of a built-in function '__ubsan_handle_builtin_unreachable' because it conflicts with attribute 'const' [-Werror=attributes]
This is actually a GCC's bug. In GCC internals
__ubsan_handle_builtin_unreachable() declared with both 'noreturn' and
'const' attributes instead of only 'noreturn':
https://gcc.gnu.org/bugzilla/show_bug.cgi?id=84210
Workaround this by removing the noreturn attribute.
[aryabinin: add information about GCC bug in changelog]
Link: http://lkml.kernel.org/r/20181107144516.4587-1-aryabinin@virtuozzo.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Acked-by: Olof Johansson <olof@lixom.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Janne Huttunen [Fri, 16 Nov 2018 23:08:32 +0000 (15:08 -0800)]
mm/vmstat.c: fix NUMA statistics updates
Scan through the whole array to see if an update is needed. While we're
at it, use sizeof() to be safe against any possible type changes in the
future.
The bug here is that we wouldn't sync per-cpu counters into global ones
if there was an update of numa_stats for higher cpus. Highly
theoretical one though because it is much more probable that zone_stats
are updated so we would refresh anyway. So I wouldn't bother to mark
this for stable, yet something nice to fix.
[mhocko@suse.com: changelog enhancement]
Link: http://lkml.kernel.org/r/1541601517-17282-1-git-send-email-janne.huttunen@nokia.com
Fixes: 1d90ca897cb0 ("mm: update NUMA counter threshold size")
Signed-off-by: Janne Huttunen <janne.huttunen@nokia.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mike Rapoport [Fri, 16 Nov 2018 23:08:29 +0000 (15:08 -0800)]
mm/gup.c: fix follow_page_mask() kerneldoc comment
Commit
df06b37ffe5a ("mm/gup: cache dev_pagemap while pinning pages")
modified the signature of follow_page_mask() but left the parameter
description behind.
Update the description to make the code and comments agree again.
While at it, update formatting of the return value description to match
Documentation/doc-guide/kernel-doc.rst guidelines.
Link: http://lkml.kernel.org/r/1541603316-27832-1-git-send-email-rppt@linux.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Wengang Wang [Fri, 16 Nov 2018 23:08:25 +0000 (15:08 -0800)]
ocfs2: free up write context when direct IO failed
The write context should also be freed even when direct IO failed.
Otherwise a memory leak is introduced and entries remain in
oi->ip_unwritten_list causing the following BUG later in unlink path:
ERROR: bug expression: !list_empty(&oi->ip_unwritten_list)
ERROR: Clear inode of 215043, inode has unwritten extents
...
Call Trace:
? __set_current_blocked+0x42/0x68
ocfs2_evict_inode+0x91/0x6a0 [ocfs2]
? bit_waitqueue+0x40/0x33
evict+0xdb/0x1af
iput+0x1a2/0x1f7
do_unlinkat+0x194/0x28f
SyS_unlinkat+0x1b/0x2f
do_syscall_64+0x79/0x1ae
entry_SYSCALL_64_after_hwframe+0x151/0x0
This patch also logs, with frequency limit, direct IO failures.
Link: http://lkml.kernel.org/r/20181102170632.25921-1-wen.gang.wang@oracle.com
Signed-off-by: Wengang Wang <wen.gang.wang@oracle.com>
Reviewed-by: Junxiao Bi <junxiao.bi@oracle.com>
Reviewed-by: Changwei Ge <ge.changwei@h3c.com>
Reviewed-by: Joseph Qi <jiangqi903@gmail.com>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Randy Dunlap [Fri, 16 Nov 2018 23:08:22 +0000 (15:08 -0800)]
scripts/faddr2line: fix location of start_kernel in comment
Fix a source file reference location to the correct path name.
Link: http://lkml.kernel.org/r/1d50bd3d-178e-dcd8-779f-9711887440eb@infradead.org
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Roman Gushchin [Fri, 16 Nov 2018 23:08:18 +0000 (15:08 -0800)]
mm: don't reclaim inodes with many attached pages
Spock reported that commit
172b06c32b94 ("mm: slowly shrink slabs with a
relatively small number of objects") leads to a regression on his setup:
periodically the majority of the pagecache is evicted without an obvious
reason, while before the change the amount of free memory was balancing
around the watermark.
The reason behind is that the mentioned above change created some
minimal background pressure on the inode cache. The problem is that if
an inode is considered to be reclaimed, all belonging pagecache page are
stripped, no matter how many of them are there. So, if a huge
multi-gigabyte file is cached in the memory, and the goal is to reclaim
only few slab objects (unused inodes), we still can eventually evict all
gigabytes of the pagecache at once.
The workload described by Spock has few large non-mapped files in the
pagecache, so it's especially noticeable.
To solve the problem let's postpone the reclaim of inodes, which have
more than 1 attached page. Let's wait until the pagecache pages will be
evicted naturally by scanning the corresponding LRU lists, and only then
reclaim the inode structure.
Link: http://lkml.kernel.org/r/20181023164302.20436-1-guro@fb.com
Signed-off-by: Roman Gushchin <guro@fb.com>
Reported-by: Spock <dairinin@gmail.com>
Tested-by: Spock <dairinin@gmail.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Rik van Riel <riel@surriel.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: <stable@vger.kernel.org> [4.19.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michal Hocko [Fri, 16 Nov 2018 23:08:15 +0000 (15:08 -0800)]
mm, memory_hotplug: check zone_movable in has_unmovable_pages
Page state checks are racy. Under a heavy memory workload (e.g. stress
-m 200 -t 2h) it is quite easy to hit a race window when the page is
allocated but its state is not fully populated yet. A debugging patch to
dump the struct page state shows
has_unmovable_pages: pfn:0x10dfec00, found:0x1, count:0x0
page:
ffffea0437fb0000 count:1 mapcount:1 mapping:
ffff880e05239841 index:0x7f26e5000 compound_mapcount: 1
flags: 0x5fffffc0090034(uptodate|lru|active|head|swapbacked)
Note that the state has been checked for both PageLRU and PageSwapBacked
already. Closing this race completely would require some sort of retry
logic. This can be tricky and error prone (think of potential endless
or long taking loops).
Workaround this problem for movable zones at least. Such a zone should
only contain movable pages. Commit
15c30bc09085 ("mm, memory_hotplug:
make has_unmovable_pages more robust") has told us that this is not
strictly true though. Bootmem pages should be marked reserved though so
we can move the original check after the PageReserved check. Pages from
other zones are still prone to races but we even do not pretend that
memory hotremove works for those so pre-mature failure doesn't hurt that
much.
Link: http://lkml.kernel.org/r/20181106095524.14629-1-mhocko@kernel.org
Fixes: 15c30bc09085 ("mm, memory_hotplug: make has_unmovable_pages more robust")
Signed-off-by: Michal Hocko <mhocko@suse.com>
Reported-by: Baoquan He <bhe@redhat.com>
Tested-by: Baoquan He <bhe@redhat.com>
Acked-by: Baoquan He <bhe@redhat.com>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Vasily Averin [Fri, 16 Nov 2018 23:08:11 +0000 (15:08 -0800)]
mm/swapfile.c: use kvzalloc for swap_info_struct allocation
Commit
a2468cc9bfdf ("swap: choose swap device according to numa node")
changed 'avail_lists' field of 'struct swap_info_struct' to an array.
In popular linux distros it increased size of swap_info_struct up to 40
Kbytes and now swap_info_struct allocation requires order-4 page.
Switch to kvzmalloc allows to avoid unexpected allocation failures.
Link: http://lkml.kernel.org/r/fc23172d-3c75-21e2-d551-8b1808cbe593@virtuozzo.com
Fixes: a2468cc9bfdf ("swap: choose swap device according to numa node")
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Acked-by: Aaron Lu <aaron.lu@intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Huang Ying <ying.huang@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Aaro Koskinen [Fri, 16 Nov 2018 23:08:08 +0000 (15:08 -0800)]
MAINTAINERS: update OMAP MMC entry
Jarkko's e-mail address hasn't worked for a long time. We still want to
keep this driver working as it is critical for some of the OMAP boards.
I use and test this driver frequently, so change myself as a maintainer
with "Odd Fixes" status.
Link: http://lkml.kernel.org/r/20181106222750.12939-1-aaro.koskinen@iki.fi
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mike Kravetz [Fri, 16 Nov 2018 23:08:04 +0000 (15:08 -0800)]
hugetlbfs: fix kernel BUG at fs/hugetlbfs/inode.c:444!
This bug has been experienced several times by the Oracle DB team. The
BUG is in remove_inode_hugepages() as follows:
/*
* If page is mapped, it was faulted in after being
* unmapped in caller. Unmap (again) now after taking
* the fault mutex. The mutex will prevent faults
* until we finish removing the page.
*
* This race can only happen in the hole punch case.
* Getting here in a truncate operation is a bug.
*/
if (unlikely(page_mapped(page))) {
BUG_ON(truncate_op);
In this case, the elevated map count is not the result of a race.
Rather it was incorrectly incremented as the result of a bug in the huge
pmd sharing code. Consider the following:
- Process A maps a hugetlbfs file of sufficient size and alignment
(PUD_SIZE) that a pmd page could be shared.
- Process B maps the same hugetlbfs file with the same size and
alignment such that a pmd page is shared.
- Process B then calls mprotect() to change protections for the mapping
with the shared pmd. As a result, the pmd is 'unshared'.
- Process B then calls mprotect() again to chage protections for the
mapping back to their original value. pmd remains unshared.
- Process B then forks and process C is created. During the fork
process, we do dup_mm -> dup_mmap -> copy_page_range to copy page
tables. Copying page tables for hugetlb mappings is done in the
routine copy_hugetlb_page_range.
In copy_hugetlb_page_range(), the destination pte is obtained by:
dst_pte = huge_pte_alloc(dst, addr, sz);
If pmd sharing is possible, the returned pointer will be to a pte in an
existing page table. In the situation above, process C could share with
either process A or process B. Since process A is first in the list,
the returned pte is a pointer to a pte in process A's page table.
However, the check for pmd sharing in copy_hugetlb_page_range is:
/* If the pagetables are shared don't copy or take references */
if (dst_pte == src_pte)
continue;
Since process C is sharing with process A instead of process B, the
above test fails. The code in copy_hugetlb_page_range which follows
assumes dst_pte points to a huge_pte_none pte. It copies the pte entry
from src_pte to dst_pte and increments this map count of the associated
page. This is how we end up with an elevated map count.
To solve, check the dst_pte entry for huge_pte_none. If !none, this
implies PMD sharing so do not copy.
Link: http://lkml.kernel.org/r/20181105212315.14125-1-mike.kravetz@oracle.com
Fixes: c5c99429fa57 ("fix hugepages leak due to pagetable page sharing")
Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com>
Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: "Kirill A . Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Prakash Sangappa <prakash.sangappa@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Olof Johansson [Fri, 16 Nov 2018 23:08:00 +0000 (15:08 -0800)]
kernel/sched/psi.c: simplify cgroup_move_task()
The existing code triggered an invalid warning about 'rq' possibly being
used uninitialized. Instead of doing the silly warning suppression by
initializa it to NULL, refactor the code to bail out early instead.
Warning was:
kernel/sched/psi.c: In function `cgroup_move_task':
kernel/sched/psi.c:639:13: warning: `rq' may be used uninitialized in this function [-Wmaybe-uninitialized]
Link: http://lkml.kernel.org/r/20181103183339.8669-1-olof@lixom.net
Fixes: 2ce7135adc9ad ("psi: cgroup support")
Signed-off-by: Olof Johansson <olof@lixom.net>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Vitaly Wool [Fri, 16 Nov 2018 23:07:56 +0000 (15:07 -0800)]
z3fold: fix possible reclaim races
Reclaim and free can race on an object which is basically fine but in
order for reclaim to be able to map "freed" object we need to encode
object length in the handle. handle_to_chunks() is then introduced to
extract object length from a handle and use it during mapping.
Moreover, to avoid racing on a z3fold "headless" page release, we should
not try to free that page in z3fold_free() if the reclaim bit is set.
Also, in the unlikely case of trying to reclaim a page being freed, we
should not proceed with that page.
While at it, fix the page accounting in reclaim function.
This patch supersedes "[PATCH] z3fold: fix reclaim lock-ups".
Link: http://lkml.kernel.org/r/20181105162225.74e8837d03583a9b707cf559@gmail.com
Signed-off-by: Vitaly Wool <vitaly.vul@sony.com>
Signed-off-by: Jongseok Kim <ks77sj@gmail.com>
Reported-by-by: Jongseok Kim <ks77sj@gmail.com>
Reviewed-by: Snild Dolkow <snild@sony.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 16 Nov 2018 19:18:36 +0000 (13:18 -0600)]
Merge tag 'fsnotify_for_v4.20-rc3' of git://git./linux/kernel/git/jack/linux-fs
Pull fsnotify fix from Jan Kara:
"One small fsnotify fix for duplicate events"
* tag 'fsnotify_for_v4.20-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
fanotify: fix handling of events on child sub-directory
Linus Torvalds [Fri, 16 Nov 2018 17:38:14 +0000 (11:38 -0600)]
Merge tag 'gfs2-4.20.fixes3' of git://git./linux/kernel/git/gfs2/linux-gfs2
Pull bfs2 fixes from Andreas Gruenbacher:
"Fix two bugs leading to leaked buffer head references:
- gfs2: Put bitmap buffers in put_super
- gfs2: Fix iomap buffer head reference counting bug
And one bug leading to significant slow-downs when deleting large
files:
- gfs2: Fix metadata read-ahead during truncate (2)"
* tag 'gfs2-4.20.fixes3' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2:
gfs2: Fix iomap buffer head reference counting bug
gfs2: Fix metadata read-ahead during truncate (2)
gfs2: Put bitmap buffers in put_super
Andreas Gruenbacher [Sun, 11 Nov 2018 11:15:21 +0000 (11:15 +0000)]
gfs2: Fix iomap buffer head reference counting bug
GFS2 passes the inode buffer head (dibh) from gfs2_iomap_begin to
gfs2_iomap_end in iomap->private. It sets that private pointer in
gfs2_iomap_get. Users of gfs2_iomap_get other than gfs2_iomap_begin
would have to release iomap->private, but this isn't done correctly,
leading to a leak of buffer head references.
To fix this, move the code for setting iomap->private from
gfs2_iomap_get to gfs2_iomap_begin.
Fixes: 64bc06bb32 ("gfs2: iomap buffered write support")
Cc: stable@vger.kernel.org # v4.19+
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 16 Nov 2018 16:37:27 +0000 (10:37 -0600)]
Merge branch 'linus' of git://git./linux/kernel/git/herbert/crypto-2.6
Pull crypto fixes from Herbert Xu:
"This fixes the following issues:
- Potential memory overwrite in simd
- Kernel info leaks in crypto_user
- NULL dereference and use-after-free in hisilicon"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: user - Zeroize whole structure given to user space
crypto: user - fix leaking uninitialized memory to userspace
crypto: simd - correctly take reqsize of wrapped skcipher into account
crypto: hisilicon - Fix reference after free of memories on error path
crypto: hisilicon - Fix NULL dereference for same dst and src
Linus Torvalds [Fri, 16 Nov 2018 16:17:29 +0000 (10:17 -0600)]
Merge tag 'drm-fixes-2018-11-16' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Live from Vancouver, SoC maintainer talk, this weeks drm fixes pull
for rc3:
omapdrm:
- regression fixes for the reordering bridge stuff that went into rc1
i915:
- incorrect EU count fix
- HPD storm fix
- MST fix
- relocation fix for gen4/5
amdgpu:
- huge page handling fix
- IH ring setup
- XGMI aperture setup
- watermark setup fix
misc:
- docs and MST fix"
* tag 'drm-fixes-2018-11-16' of git://anongit.freedesktop.org/drm/drm: (23 commits)
drm/i915: Account for scale factor when calculating initial phase
drm/i915: Clean up skl_program_scaler()
drm/i915: Move programming plane scaler to its own function.
drm/i915/icl: Drop spurious register read from icl_dbuf_slices_update
drm/i915: fix broadwell EU computation
drm/amdgpu: fix huge page handling on Vega10
drm/amd/pp: Fix truncated clock value when set watermark
drm/amdgpu: fix bug with IH ring setup
drm/meson: venc: dmt mode must use encp
drm/amdgpu: set system aperture to cover whole FB region
drm/i915: Fix hpd handling for pins with two encoders
drm/i915/execlists: Force write serialisation into context image vs execution
drm/i915/icl: Fix power well 2 wrt. DC-off toggling order
drm/i915: Fix NULL deref when re-enabling HPD IRQs on systems with MST
drm/i915: Fix possible race in intel_dp_add_mst_connector()
drm/i915/ringbuffer: Delay after EMIT_INVALIDATE for gen4/gen5
drm/omap: dsi: Fix missing of_platform_depopulate()
drm/omap: Move DISPC runtime PM handling to omapdrm
drm/omap: dsi: Ensure the device is active during probe
drm/omap: hdmi4: Ensure the device is active during bind
...
Linus Torvalds [Fri, 16 Nov 2018 16:14:54 +0000 (10:14 -0600)]
Merge tag 'powerpc-4.20-3' of git://git./linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Two weeks worth of fixes since rc1.
- I broke 16-byte alignment of the stack when we moved PPR into
pt_regs. Despite being required by the ABI this broke almost
nothing, we eventually hit it in code where GCC does arithmetic on
the stack pointer assuming the bottom 4 bits are clear. Fix it by
padding the in-kernel pt_regs by 8 bytes.
- A couple of commits fixing minor bugs in the recent SLB rewrite.
- A build fix related to tracepoints in KVM in some configurations.
- Our old "IO workarounds" code written for Cell couldn't coexist in
a kernel that runs on Power9 with the Radix MMU, fix that.
- Remove the NPU DMA ops, these just printed a warning and should
never have been called.
- Suppress an overly chatty message triggered by CPU hotplug in some
configs.
- Two small selftest fixes.
Thanks to: Alistair Popple, Gustavo Romero, Nicholas Piggin, Satheesh
Rajendran, Scott Wood"
* tag 'powerpc-4.20-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
selftests/powerpc: Adjust wild_bctr to build with old binutils
powerpc/64: Fix kernel stack 16-byte alignment
powerpc/numa: Suppress "VPHN is not supported" messages
selftests/powerpc: Fix wild_bctr test to work on ppc64
powerpc/io: Fix the IO workarounds code to work with Radix
powerpc/mm/64s: Fix preempt warning in slb_allocate_kernel()
KVM: PPC: Move and undef TRACE_INCLUDE_PATH/FILE
powerpc/mm/64s: Only use slbfee on CPUs that support it
powerpc/mm/64s: Use PPC_SLBFEE macro
powerpc/mm/64s: Consolidate SLB assertions
powerpc/powernv/npu: Remove NPU DMA ops
Linus Torvalds [Fri, 16 Nov 2018 16:10:27 +0000 (10:10 -0600)]
Merge tag 'xtensa-
20181115' of git://github.com/jcmvbkbc/linux-xtensa
Pull Xtensa fixes from Max Filippov:
- fix stack alignment for bFLT binaries.
- fix physical-to-virtual address translation for boot parameters in
MMUv3 256+256 and 512+512 virtual memory layouts.
* tag 'xtensa-
20181115' of git://github.com/jcmvbkbc/linux-xtensa:
xtensa: fix boot parameters address translation
xtensa: make sure bFLT stack is 16 byte aligned
Linus Torvalds [Fri, 16 Nov 2018 15:31:59 +0000 (09:31 -0600)]
Merge tag 'for-linus-
20181115' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
- Discard loop fix, caused by integer overflow (Dave)
- Blacklist of Samsung drive that hangs with power management (Diego)
- Copy bio priority when cloning it (Hannes)
- Fix race condition exposed in floppy (me)
- Fix SCSI queue cleanup regression. While elusive, it caused oopses in
queue running (Ming)
- Fix bad string copy in kyber tracing (Omar)
* tag 'for-linus-
20181115' of git://git.kernel.dk/linux-block:
SCSI: fix queue cleanup race before queue initialization is done
block: fix 32 bit overflow in __blkdev_issue_discard()
libata: blacklist SAMSUNG MZ7TD256HAFV-000L9 SSD
block: copy ioprio in __bio_clone_fast() and bounce
kyber: fix wrong strlcpy() size in trace_kyber_latency()
floppy: fix race condition in __floppy_read_block_0()
Linus Torvalds [Fri, 16 Nov 2018 15:30:13 +0000 (09:30 -0600)]
Merge tag 'fuse-fixes-4.20-rc3' of git://git./linux/kernel/git/mszeredi/fuse
Pull fuse fixes from Miklos Szeredi:
"A couple of fixes, all bound for -stable (i.e. not regressions in this
cycle)"
* tag 'fuse-fixes-4.20-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: fix use-after-free in fuse_direct_IO()
fuse: fix possibly missed wake-up after abort
fuse: fix leaked notify reply
Dave Airlie [Thu, 15 Nov 2018 22:52:14 +0000 (08:52 +1000)]
Merge tag 'drm-intel-fixes-2018-11-15' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
- Fix Bugzilla #108712: Fix incorrect EU count report from kernel
- Fix to account for scale factor when calculating initial phase on scaled output
- Avoid too trigger-happy HPD storm detection and fix a race and an OOPS for MST systems.
- Relocation race fix for Gen4/5
- A couple ICL fixes and dependencies for above Fixes:.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181115164709.GA13430@jlahtine-desk.ger.corp.intel.com
Linus Torvalds [Thu, 15 Nov 2018 17:26:09 +0000 (11:26 -0600)]
Merge tag 'selinux-pr-
20181115' of git://git./linux/kernel/git/pcmoore/selinux
Pull SELinux fixes from Paul Moore:
"Two small SELinux fixes for v4.20.
Ondrej's patch adds a check on user input, and my patch ensures we
don't look past the end of a buffer.
Both patches are quite small and pass the selinux-testsuite"
* tag 'selinux-pr-
20181115' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux:
selinux: fix non-MLS handling in mls_context_to_sid()
selinux: check length properly in SCTP bind hook
Linus Torvalds [Thu, 15 Nov 2018 17:20:06 +0000 (11:20 -0600)]
Merge tag 'pinctrl-v4.20-2' of git://git./linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
- A bunch of fixes for the Allwinner meson platform
- Establish a git repo for Intel pin control in MAINTAINERS
* tag 'pinctrl-v4.20-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
MAINTAINERS: Add tree link for Intel pin control driver
pinctrl: meson: fix meson8b ao pull register bits
pinctrl: meson: fix meson8 ao pull register bits
pinctrl: meson: fix gxl ao pull register bits
pinctrl: meson: fix gxbb ao pull register bits
pinctrl: meson: fix pinconf bias disable
Linus Torvalds [Thu, 15 Nov 2018 16:59:37 +0000 (10:59 -0600)]
Merge tag 'nfs-for-4.20-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
"Highlights include:
Stable fixes:
- Don't exit the NFSv4 state manager without clearing
NFS4CLNT_MANAGER_RUNNING
Bugfixes:
- Fix an Oops when destroying the RPCSEC_GSS credential cache
- Fix an Oops during delegation callbacks
- Ensure that the NFSv4 state manager exits the loop on SIGKILL
- Fix a bogus get/put in generic_key_to_expire()"
* tag 'nfs-for-4.20-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFSv4: Fix an Oops during delegation callbacks
SUNRPC: Fix a bogus get/put in generic_key_to_expire()
SUNRPC: Fix a Oops when destroying the RPCSEC_GSS credential cache
NFSv4: Ensure that the state manager exits the loop on SIGKILL
NFSv4: Don't exit the state manager without clearing NFS4CLNT_MANAGER_RUNNING
Dave Airlie [Thu, 15 Nov 2018 16:14:42 +0000 (02:14 +1000)]
Merge branch 'drm-fixes-4.20' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
Fixes for 4.20:
- Fix for huge page handling that caused a GPUVM fault in some cases
- Fix IH ring setup
- Fix for xgmi aperture setup
- Fix for watermark setup for SMU
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181114171853.2866-1-alexander.deucher@amd.com
Dave Airlie [Thu, 15 Nov 2018 16:12:27 +0000 (02:12 +1000)]
Merge tag 'drm-misc-fixes-2018-11-14' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
Cross-subsystem:
- omap: Instantiate dss children in omapdss instead of mach (Laurent)
Other:
- htmldocs build warning (Sean)
- MST NULL deref fix (Stanislav)
- omap: Various runtime ref gets on probe/bind (Laurent)
- omap: Fix to the above dss children patch (Tony)
Cc: Sean Paul <sean@poorly.run>
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20181114204542.GA52569@art_vandelay
Gustavo Romero [Thu, 15 Nov 2018 02:33:30 +0000 (21:33 -0500)]
selftests/powerpc: Adjust wild_bctr to build with old binutils
Currently the selftest wild_bctr can fail to build when an old gcc is
used, notably on gcc using a binutils version <= 2.27, because the
assembler does not support the integer suffix UL.
This patch adjusts the wild_bctr test so the REG_POISON value is still
treated as an unsigned long for the shifts on compilation but the UL
suffix is absent on the stringification, so the inline asm code
generated has no UL suffixes.
Signed-off-by: Gustavo Romero <gromero@linux.vnet.ibm.com>
[mpe: Wrap long line]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Ville Syrjälä [Wed, 14 Nov 2018 13:32:55 +0000 (15:32 +0200)]
drm/i915: Account for scale factor when calculating initial phase
To get the initial phase correct we need to account for the scale
factor as well. I forgot this initially and was mostly looking at
heavily upscaled content where the minor difference between -0.5
and the proper initial phase was not readily apparent.
And let's toss in a comment that tries to explain the formula
a little bit.
v2: The initial phase upper limit is 1.5, not 24.0!
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Fixes: 0a59952b24e2 ("drm/i915: Configure SKL+ scaler initial phase correctly")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181029181820.21956-1-ville.syrjala@linux.intel.com
Tested-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Tested-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> #irc
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> #irc
(cherry picked from commit
e7a278a329dd8aa2c70c564849f164cb5673689c)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Ville Syrjälä [Wed, 14 Nov 2018 11:49:24 +0000 (13:49 +0200)]
drm/i915: Clean up skl_program_scaler()
Remove the "sizes are 0 based" stuff that is not even true for the
scaler.
v2: Rebase
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181101151736.20522-1-ville.syrjala@linux.intel.com
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
(cherry picked from commit
d0105af939769393d6447a04cee2d1ae12e3f09a)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Maarten Lankhorst [Wed, 14 Nov 2018 11:49:23 +0000 (13:49 +0200)]
drm/i915: Move programming plane scaler to its own function.
This cleans the code up slightly, and will make other changes easier.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180920102711.4184-8-maarten.lankhorst@linux.intel.com
(cherry picked from commit
ab5c60bf76755d24ae8de5c1c6ac594934656ace)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Ard Biesheuvel [Wed, 14 Nov 2018 17:55:44 +0000 (09:55 -0800)]
efi: Permit calling efi_mem_reserve_persistent() from atomic context
Currently, efi_mem_reserve_persistent() may not be called from atomic
context, since both the kmalloc() call and the memremap() call may
sleep.
The kmalloc() call is easy enough to fix, but the memremap() call
needs to be moved into an init hook since we cannot control the
memory allocation behavior of memremap() at the call site.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/20181114175544.12860-6-ard.biesheuvel@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Ard Biesheuvel [Wed, 14 Nov 2018 17:55:43 +0000 (09:55 -0800)]
efi/arm: Defer persistent reservations until after paging_init()
The new memory EFI reservation feature we introduced to allow memory
reservations to persist across kexec may trigger an unbounded number
of calls to memblock_reserve(). The memblock subsystem can deal with
this fine, but not before memblock resizing is enabled, which we can
only do after paging_init(), when the memory we reallocate the array
into is actually mapped.
So break out the memreserve table processing into a separate routine
and call it after paging_init() on arm64. On ARM, because of limited
reviewing bandwidth of the maintainer, we cannot currently fix this,
so instead, disable the EFI persistent memreserve entirely on ARM so
we can fix it later.
Tested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/20181114175544.12860-5-ard.biesheuvel@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Ard Biesheuvel [Wed, 14 Nov 2018 17:55:42 +0000 (09:55 -0800)]
efi/arm/libstub: Pack FDT after populating it
Commit:
24d7c494ce46 ("efi/arm-stub: Round up FDT allocation to mapping size")
increased the allocation size for the FDT image created by the stub to a
fixed value of 2 MB, to simplify the former code that made several
attempts with increasing values for the size. This is reasonable
given that the allocation is of type EFI_LOADER_DATA, which is released
to the kernel unless it is explicitly memblock_reserve()d by the early
boot code.
However, this allocation size leaked into the 'size' field of the FDT
header metadata, and so the entire allocation remains occupied by the
device tree binary, even if most of it is not used to store device tree
information.
So call fdt_pack() to shrink the FDT data structure to its minimum size
after populating all the fields, so that the remaining memory is no
longer wasted.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: <stable@vger.kernel.org> # v4.12+
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Fixes: 24d7c494ce46 ("efi/arm-stub: Round up FDT allocation to mapping size")
Link: http://lkml.kernel.org/r/20181114175544.12860-4-ard.biesheuvel@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Ard Biesheuvel [Wed, 14 Nov 2018 17:55:41 +0000 (09:55 -0800)]
efi/arm: Revert deferred unmap of early memmap mapping
Commit:
3ea86495aef2 ("efi/arm: preserve early mapping of UEFI memory map longer for BGRT")
deferred the unmap of the early mapping of the UEFI memory map to
accommodate the ACPI BGRT code, which looks up the memory type that
backs the BGRT table to validate it against the requirements of the UEFI spec.
Unfortunately, this causes problems on ARM, which does not permit
early mappings to persist after paging_init() is called, resulting
in a WARN() splat. Since we don't support the BGRT table on ARM anway,
let's revert ARM to the old behaviour, which is to take down the
early mapping at the end of efi_init().
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Fixes: 3ea86495aef2 ("efi/arm: preserve early mapping of UEFI memory ...")
Link: http://lkml.kernel.org/r/20181114175544.12860-3-ard.biesheuvel@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Waiman Long [Wed, 14 Nov 2018 17:55:40 +0000 (09:55 -0800)]
efi: Fix debugobjects warning on 'efi_rts_work'
The following commit:
9dbbedaa6171 ("efi: Make efi_rts_work accessible to efi page fault handler")
converted 'efi_rts_work' from an auto variable to a global variable.
However, when submitting the work, INIT_WORK_ONSTACK() was still used,
causing the following complaint from debugobjects:
ODEBUG: object
00000000ed27b500 is NOT on stack
00000000c7d38760, but annotated.
Change the macro to just INIT_WORK() to eliminate the warning.
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Sai Praneeth Prakhya <sai.praneeth.prakhya@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Fixes: 9dbbedaa6171 ("efi: Make efi_rts_work accessible to efi page fault handler")
Link: http://lkml.kernel.org/r/20181114175544.12860-2-ard.biesheuvel@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Nicholas Piggin [Thu, 15 Nov 2018 02:34:27 +0000 (12:34 +1000)]
powerpc/64: Fix kernel stack 16-byte alignment
Commit
4c2de74cc869 ("powerpc/64: Interrupts save PPR on stack rather
than thread_struct") changed sizeof(struct pt_regs) % 16 from 0 to 8,
which causes the interrupt frame allocation on kernel entry to put the
kernel stack out of alignment.
Quadword (16-byte) alignment for the stack is required by both the
64-bit v1 ABI (v1.9 § 3.2.2) and the 64-bit v2 ABI (v1.1 § 2.2.2.1).
Add a pad field to fix alignment, and add a BUILD_BUG_ON to catch this
in future.
Fixes: 4c2de74cc869 ("powerpc/64: Interrupts save PPR on stack rather than thread_struct")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Michael Roth [Fri, 9 Nov 2018 03:27:23 +0000 (21:27 -0600)]
KVM: PPC: Book3S HV: Fix handling for interrupted H_ENTER_NESTED
While running a nested guest VCPU on L0 via H_ENTER_NESTED hcall, a
pending signal in the L0 QEMU process can generate the following
sequence:
ret0 = kvmppc_pseries_do_hcall()
ret1 = kvmhv_enter_nested_guest()
ret2 = kvmhv_run_single_vcpu()
if (ret2 == -EINTR)
return H_INTERRUPT
if (ret1 == H_INTERRUPT)
kvmppc_set_gpr(vcpu, 3, 0)
return -EINTR
/* skipped: */
kvmppc_set_gpr(vcpu, 3, ret)
vcpu->arch.hcall_needed = 0
return RESUME_GUEST
which causes an exit to L0 userspace with ret0 == -EINTR.
The intention seems to be to set the hcall return value to 0 (via
VCPU r3) so that L1 will see a successful return from H_ENTER_NESTED
once we resume executing the VCPU. However, because we don't set
vcpu->arch.hcall_needed = 0, we do the following once userspace
resumes execution via kvm_arch_vcpu_ioctl_run():
...
} else if (vcpu->arch.hcall_needed) {
int i
kvmppc_set_gpr(vcpu, 3, run->papr_hcall.ret);
for (i = 0; i < 9; ++i)
kvmppc_set_gpr(vcpu, 4 + i, run->papr_hcall.args[i]);
vcpu->arch.hcall_needed = 0;
since vcpu->arch.hcall_needed == 1 indicates that userspace should
have handled the hcall and stored the return value in
run->papr_hcall.ret. Since that's not the case here, we can get an
unexpected value in VCPU r3, which can result in
kvmhv_p9_guest_entry() reporting an unexpected trap value when it
returns from H_ENTER_NESTED, causing the following register dump to
console via subsequent call to kvmppc_handle_exit_hv() in L1:
[ 350.612854] vcpu
00000000f9564cf8 (0):
[ 350.612915] pc =
c00000000013eb98 msr =
8000000000009033 trap = 1
[ 350.613020] r 0 =
c0000000004b9044 r16 =
0000000000000000
[ 350.613075] r 1 =
c00000007cffba30 r17 =
0000000000000000
[ 350.613120] r 2 =
c00000000178c100 r18 =
00007fffc24f3b50
[ 350.613166] r 3 =
c00000007ef52480 r19 =
00007fffc24fff58
[ 350.613212] r 4 =
0000000000000000 r20 =
00000a1e96ece9d0
[ 350.613253] r 5 =
70616d00746f6f72 r21 =
00000a1ea117c9b0
[ 350.613295] r 6 =
0000000000000020 r22 =
00000a1ea1184360
[ 350.613338] r 7 =
c0000000783be440 r23 =
0000000000000003
[ 350.613380] r 8 =
fffffffffffffffc r24 =
00000a1e96e9e124
[ 350.613423] r 9 =
c00000007ef52490 r25 =
00000000000007ff
[ 350.613469] r10 =
0000000000000004 r26 =
c00000007eb2f7a0
[ 350.613513] r11 =
b0616d0009eccdb2 r27 =
c00000007cffbb10
[ 350.613556] r12 =
c0000000004b9000 r28 =
c00000007d83a2c0
[ 350.613597] r13 =
c000000001b00000 r29 =
c0000000783cdf68
[ 350.613639] r14 =
0000000000000000 r30 =
0000000000000000
[ 350.613681] r15 =
0000000000000000 r31 =
c00000007cffbbf0
[ 350.613723] ctr =
c0000000004b9000 lr =
c0000000004b9044
[ 350.613765] srr0 =
0000772f954dd48c srr1 =
800000000280f033
[ 350.613808] sprg0 =
0000000000000000 sprg1 =
c000000001b00000
[ 350.613859] sprg2 =
0000772f9565a280 sprg3 =
0000000000000000
[ 350.613911] cr =
88002848 xer =
0000000020040000 dsisr =
42000000
[ 350.613962] dar =
0000772f95390000
[ 350.614031] fault dar =
c000000244b278c0 dsisr =
00000000
[ 350.614073] SLB (0 entries):
[ 350.614157] lpcr =
0040000003d40413 sdr1 =
0000000000000000 last_inst =
ffffffff
[ 350.614252] trap=0x1 | pc=0xc00000000013eb98 | msr=0x8000000000009033
followed by L1's QEMU reporting the following before stopping execution
of the nested guest:
KVM: unknown exit, hardware reason 1
NIP
c00000000013eb98 LR
c0000000004b9044 CTR
c0000000004b9000 XER
0000000020040000 CPU#0
MSR
8000000000009033 HID0
0000000000000000 HF
8000000000000000 iidx 3 didx 3
TB
00000000 00000000 DECR
00000000
GPR00
c0000000004b9044 c00000007cffba30 c00000000178c100 c00000007ef52480
GPR04
0000000000000000 70616d00746f6f72 0000000000000020 c0000000783be440
GPR08
fffffffffffffffc c00000007ef52490 0000000000000004 b0616d0009eccdb2
GPR12
c0000000004b9000 c000000001b00000 0000000000000000 0000000000000000
GPR16
0000000000000000 0000000000000000 00007fffc24f3b50 00007fffc24fff58
GPR20
00000a1e96ece9d0 00000a1ea117c9b0 00000a1ea1184360 0000000000000003
GPR24
00000a1e96e9e124 00000000000007ff c00000007eb2f7a0 c00000007cffbb10
GPR28
c00000007d83a2c0 c0000000783cdf68 0000000000000000 c00000007cffbbf0
CR
88002848 [ L L - - E L G L ] RES
ffffffffffffffff
SRR0
0000772f954dd48c SRR1
800000000280f033 PVR
00000000004e1202 VRSAVE
0000000000000000
SPRG0
0000000000000000 SPRG1
c000000001b00000 SPRG2
0000772f9565a280 SPRG3
0000000000000000
SPRG4
0000000000000000 SPRG5
0000000000000000 SPRG6
0000000000000000 SPRG7
0000000000000000
HSRR0
0000000000000000 HSRR1
0000000000000000
CFAR
0000000000000000
LPCR
0000000003d40413
PTCR
0000000000000000 DAR
0000772f95390000 DSISR
0000000042000000
Fix this by setting vcpu->arch.hcall_needed = 0 to indicate completion
of H_ENTER_NESTED before we exit to L0 userspace.
Fixes: 360cae313702 ("KVM: PPC: Book3S HV: Nested guest entry via hypercall")
Cc: linuxppc-dev@ozlabs.org
Cc: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Reviewed-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Linus Torvalds [Wed, 14 Nov 2018 23:14:40 +0000 (17:14 -0600)]
Merge tag 'riscv-for-linus-4.20-rc2' of git://git./linux/kernel/git/palmer/riscv-linux
Pull RISC-V fixes from Palmer Dabbelt:
"This contains a few patches that fix various issues in the RISC-V
port:
- enable printk timestamps in the RISC-V defconfig.
- a whitespace fix to "struct pt_regs".
- add a "vdso_install" target for RISC-V.
- a pair of build fixes: one to fix a typo in our makefile, and one
to clean up some warnings.
There will probably be more patches from us for 4.20, but I don't have
anything that's ready to go right now so I'm going to hold off a bit.
Right now the only concrete thing I know I want to make sure gets
sorted out is our 32-bit stat interface, which I don't want sitting in
limbo for another cycle as we have to get RV32I glibc sone"
* tag 'riscv-for-linus-4.20-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux:
RISC-V: Silence some module warnings on 32-bit
RISC-V: lib: Fix build error for 64-bit
riscv: add missing vdso_install target
riscv: fix spacing in struct pt_regs
RISC-V: defconfig: Enable printk timestamps
Linus Torvalds [Wed, 14 Nov 2018 23:07:01 +0000 (17:07 -0600)]
Merge tag 'kgdb-fixes-4.20-rc3' of https://git.linaro.org/people/daniel.thompson/linux
Pull kgdb fixes from Daniel Thompson:
"The most important changes here are two fixes for kdb regressions
causes by the hashing of %p pointers together with a fix for a
potential overflow in kdb tab completion handling (and warning fix).
Also included are a set of changes in preparation to (eventually)
enable -Wimplicit-fallthrough"
* tag 'kgdb-fixes-4.20-rc3' of https://git.linaro.org/people/daniel.thompson/linux:
kdb: kdb_support: mark expected switch fall-throughs
kdb: kdb_keyboard: mark expected switch fall-throughs
kdb: kdb_main: refactor code in kdb_md_line
kdb: Use strscpy with destination buffer size
kdb: print real address of pointers instead of hashed addresses
kdb: use correct pointer when 'btc' calls 'btt'
Linus Torvalds [Wed, 14 Nov 2018 23:03:24 +0000 (17:03 -0600)]
Merge branch 'fixes-v4.20-rc3' of git://git./linux/kernel/git/jmorris/linux-security
Pull integrity fix from James Morris:
"Fix a bug introduced with in this merge window in
82f94f24475c ("KEYS:
Provide software public key query function [ver #2]")"
* 'fixes-v4.20-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
integrity: support new struct public_key_signature encoding field
Linus Torvalds [Wed, 14 Nov 2018 21:36:45 +0000 (15:36 -0600)]
Merge tag 'acpi-4.20-rc3' of git://git./linux/kernel/git/rafael/linux-pm
Pull ACPI fix from Rafael Wysocki:
"Fix a recently introduced build issue in the xpower PMIC driver (Arnd
Bergmann)"
* tag 'acpi-4.20-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / PMIC: xpower: fix IOSF_MBI dependency
Linus Torvalds [Wed, 14 Nov 2018 21:33:45 +0000 (15:33 -0600)]
Merge tag 'pm-4.20-rc3' of git://git./linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These remove a stale DT entry left behind after recent removal of a
cpufreq driver without users, fix up error handling in the imx6q
cpufreq driver, fix two issues in the cpufreq documentation, and
update the ARM cpufreq driver.
Specifics:
- Drop stale DT binding for the arm_big_little_dt driver removed
recently (Sudeep Holla).
- Fix up error handling in the imx6q cpufreq driver to make it report
voltage scaling failures (Anson Huang).
- Fix two issues in the cpufreq documentation (Viresh Kumar, Zhao Wei
Liew).
- Fix ARM cpuidle driver initialization regression from the 4.19 time
frame and rework the driver registration part of it to simplify
code (Ulf Hansson)"
* tag 'pm-4.20-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ARM: cpuidle: Convert to use cpuidle_register|unregister()
ARM: cpuidle: Don't register the driver when back-end init returns -ENXIO
dt-bindings: cpufreq: remove stale arm_big_little_dt entry
Documentation: cpufreq: Correct a typo
cpufreq: imx6q: add return value check for voltage scale
Documentation: cpu-freq: Frequencies aren't always sorted
Linus Torvalds [Wed, 14 Nov 2018 21:31:15 +0000 (15:31 -0600)]
Merge tag 'nfsd-4.20-1' of git://linux-nfs.org/~bfields/linux
Pull nfsd fixes from Bruce Fields:
"Three nfsd bugfixes.
None are new bugs, but they all take a little effort to hit, which
might explain why they weren't found sooner"
* tag 'nfsd-4.20-1' of git://linux-nfs.org/~bfields/linux:
SUNRPC: drop pointless static qualifier in xdr_get_next_encode_buffer()
nfsd: COPY and CLONE operations require the saved filehandle to be set
sunrpc: correct the computation for page_ptr when truncating
Linus Torvalds [Wed, 14 Nov 2018 19:51:47 +0000 (13:51 -0600)]
Merge tag 'pci-v4.20-fixes-1' of git://git./linux/kernel/git/helgaas/pci
Pull PCI fix from Bjorn Helgaas:
"Revert a _PXM change that causes silent early boot failure on some AMD
ThreadRipper systems"
* tag 'pci-v4.20-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
Revert "ACPI/PCI: Pay attention to device-specific _PXM node values"
Linus Torvalds [Wed, 14 Nov 2018 19:49:29 +0000 (13:49 -0600)]
Merge tag 'scsi-fixes' of git://git./linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is mostly a set of minor and obvious fixes (three in one of the
new drivers).
The only substantial change is to move the ufs to the blk-mq now that
the merge window fixed the suspend/resume issues with blk-mq"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: qla2xxx: Initialize port speed to avoid setting lower speed
Revert "scsi: ufs: Disable blk-mq for now"
scsi: NCR5380: Return false instead of NULL
scsi: qla2xxx: Fix a typo in MODULE_PARM_DESC
scsi: hisi_sas: Remove set but not used variable 'dq_list'
scsi: myrs: only build on little-endian platforms
scsi: myrs: avoid stack overflow warning
scsi: lpfc: fix remoteport access
scsi: myrb: fix sprintf buffer overflow warning
scsi: target/core: Avoid that a kernel oops is triggered when COMPARE AND WRITE fails
Linus Torvalds [Wed, 14 Nov 2018 19:47:15 +0000 (13:47 -0600)]
Merge tag 'rtc-4.20-2' of git://git./linux/kernel/git/abelloni/linux
Pull RTC driver fixes from Alexandre Belloni:
- cmos: stop exporting alarms when not supported
- hctosys: correctly report range error
- pcf2127: fix a memory leak
* tag 'rtc-4.20-2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
rtc: pcf2127: fix a kmemleak caused in pcf2127_i2c_gather_write
rtc: hctosys: Add missing range error reporting
rtc: cmos: Do not export alarm rtc_ops when we do not support alarms
Linus Torvalds [Wed, 14 Nov 2018 19:44:52 +0000 (13:44 -0600)]
Merge branch 'for-linus' of git://git./linux/kernel/git/ebiederm/user-namespace
Pull namespace fix from Eric Biederman:
"Benjamin Coddington noticed an unkillable busy loop in the kernel that
anyone who is sufficiently motivated can trigger. This bug did not
exist in earlier kernels making this bug a regression.
I have tested the change personally and confirmed that the bug exists
and that the fix works. This fix has been picked up by linux-next and
hopefully the automated testing bots and no problems have been
reported from those sources.
Ordinarily I would let something like this sit a little longer but I
am going to be away at Linux Plumbers the rest of this week and I am
afraid if I don't send the pull request now this fix will get lost"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
mnt: fix __detach_mounts infinite loop
Linus Torvalds [Wed, 14 Nov 2018 19:42:41 +0000 (13:42 -0600)]
Merge branch 'parisc-4.20-3' of git://git./linux/kernel/git/deller/parisc-linux
Pull parisc fix from Helge Deller:
"Revert one patch which changed how spinlocks get released. It breaks
the rwlock implementation in glibc"
* 'parisc-4.20-3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Revert "Release spinlocks using ordered store"
Linus Torvalds [Wed, 14 Nov 2018 19:40:22 +0000 (13:40 -0600)]
Merge branch 'spectre' of git://git.armlinux.org.uk/~rmk/linux-arm
Pull ARM fix from Russell King:
"It was noticed that one of Julien's patches contained an error, this
fixes that up"
* 'spectre' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8810/1: vfp: Fix wrong assignement to ufp_exc
Ming Lei [Wed, 14 Nov 2018 08:25:51 +0000 (16:25 +0800)]
SCSI: fix queue cleanup race before queue initialization is done
c2856ae2f315d ("blk-mq: quiesce queue before freeing queue") has
already fixed this race, however the implied synchronize_rcu()
in blk_mq_quiesce_queue() can slow down LUN probe a lot, so caused
performance regression.
Then
1311326cf4755c7 ("blk-mq: avoid to synchronize rcu inside blk_cleanup_queue()")
tried to quiesce queue for avoiding unnecessary synchronize_rcu()
only when queue initialization is done, because it is usual to see
lots of inexistent LUNs which need to be probed.
However, turns out it isn't safe to quiesce queue only when queue
initialization is done. Because when one SCSI command is completed,
the user of sending command can be waken up immediately, then the
scsi device may be removed, meantime the run queue in scsi_end_request()
is still in-progress, so kernel panic can be caused.
In Red Hat QE lab, there are several reports about this kind of kernel
panic triggered during kernel booting.
This patch tries to address the issue by grabing one queue usage
counter during freeing one request and the following run queue.
Fixes: 1311326cf4755c7 ("blk-mq: avoid to synchronize rcu inside blk_cleanup_queue()")
Cc: Andrew Jones <drjones@redhat.com>
Cc: Bart Van Assche <bart.vanassche@wdc.com>
Cc: linux-scsi@vger.kernel.org
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
Cc: stable <stable@vger.kernel.org>
Cc: jianchao.wang <jianchao.w.wang@oracle.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Dave Chinner [Wed, 14 Nov 2018 15:17:18 +0000 (08:17 -0700)]
block: fix 32 bit overflow in __blkdev_issue_discard()
A discard cleanup merged into 4.20-rc2 causes fstests xfs/259 to
fall into an endless loop in the discard code. The test is creating
a device that is exactly 2^32 sectors in size to test mkfs boundary
conditions around the 32 bit sector overflow region.
mkfs issues a discard for the entire device size by default, and
hence this throws a sector count of 2^32 into
blkdev_issue_discard(). It takes the number of sectors to discard as
a sector_t - a 64 bit value.
The commit
ba5d73851e71 ("block: cleanup __blkdev_issue_discard")
takes this sector count and casts it to a 32 bit value before
comapring it against the maximum allowed discard size the device
has. This truncates away the upper 32 bits, and so if the lower 32
bits of the sector count is zero, it starts issuing discards of
length 0. This causes the code to fall into an endless loop, issuing
a zero length discards over and over again on the same sector.
Fixes: ba5d73851e71 ("block: cleanup __blkdev_issue_discard")
Tested-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Killed pointless WARN_ON().
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Mika Kuoppala [Fri, 9 Nov 2018 14:09:23 +0000 (16:09 +0200)]
drm/i915/icl: Drop spurious register read from icl_dbuf_slices_update
Register DBUF_CTL_S2 is read and it's value is not used. As
there is no explanation why we should prime the hardware with
read, remove it as spurious.
Fixes: aa9664ffe863 ("drm/i915/icl: Enable 2nd DBuf slice only when needed")
Cc: Mahesh Kumar <mahesh1.kumar@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181109140924.2663-1-mika.kuoppala@linux.intel.com
(cherry picked from commit
8577c319b6511fbc391f3775225fecd8b979bc26)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Lionel Landwerlin [Mon, 12 Nov 2018 12:39:31 +0000 (12:39 +0000)]
drm/i915: fix broadwell EU computation
subslice_mask is an array indexed by slice, not subslice.
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Fixes: 8cc7669355136f ("drm/i915: store all subslice masks")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=108712
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181112123931.2815-1-lionel.g.landwerlin@intel.com
(cherry picked from commit
63ac3328f0d1d37f286e397b14d9596ed09d7ca5)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Max Filippov [Wed, 14 Nov 2018 07:46:42 +0000 (23:46 -0800)]
xtensa: fix boot parameters address translation
The bootloader may pass physical address of the boot parameters structure
to the MMUv3 kernel in the register a2. Code in the _SetupMMU block in
the arch/xtensa/kernel/head.S is supposed to map that physical address to
the virtual address in the configured virtual memory layout.
This code haven't been updated when additional 256+256 and 512+512
memory layouts were introduced and it may produce wrong addresses when
used with these layouts.
Cc: stable@vger.kernel.org
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Satheesh Rajendran [Thu, 8 Nov 2018 05:17:56 +0000 (10:47 +0530)]
powerpc/numa: Suppress "VPHN is not supported" messages
When VPHN function is not supported and during cpu hotplug event,
kernel prints message 'VPHN function not supported. Disabling
polling...'. Currently it prints on every hotplug event, it floods
dmesg when a KVM guest tries to hotplug huge number of vcpus, let's
just print once and suppress further kernel prints.
Signed-off-by: Satheesh Rajendran <sathnaga@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Paul Moore [Wed, 14 Nov 2018 02:44:33 +0000 (21:44 -0500)]
selinux: fix non-MLS handling in mls_context_to_sid()
Commit
95ffe194204a ("selinux: refactor mls_context_to_sid() and make
it stricter") inadvertently changed how we handle labels that did not
contain MLS information. This patch restores the proper behavior in
mls_context_to_sid() and adds a comment explaining the proper
behavior to help ensure this doesn't happen again.
Fixes: 95ffe194204a ("selinux: refactor mls_context_to_sid() and make it stricter")
Reported-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Trond Myklebust [Tue, 13 Nov 2018 21:37:54 +0000 (16:37 -0500)]
NFSv4: Fix an Oops during delegation callbacks
If the server sends a CB_GETATTR or a CB_RECALL while the filesystem is
being unmounted, then we can Oops when releasing the inode in
nfs4_callback_getattr() and nfs4_callback_recall().
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
projects / openwrt / staging / blogic.git / log