Daniel Golle [Mon, 18 Sep 2023 15:40:30 +0000 (16:40 +0100)]
arm-trusted-firmware-mediatek: fix copy&paste error in Makefile
When adding builds for MT7981 the related Makefile sections for MT7986
have apparently been copied, but in one instance the rename from 7986 to
7981 has been omitted. Fix that now.
Fixes: 602cb4f325 ("arm-trusted-firmware-mediatek: add build for MT7981 DDR3")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Mon, 11 Sep 2023 21:49:59 +0000 (22:49 +0100)]
kernel: serial: 8250_mtk: track busclk state to avoid bus error
UARTs not used as boot console are currently broken on some MediaTek
targets due to register access depending on the bus clock being enabled.
Add patch to make sure this dependency is always met.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
David Bauer [Wed, 20 Sep 2023 18:59:35 +0000 (20:59 +0200)]
mpc85xx: correct WS-AP3715i eth LED assignment
Ethernet LED assignments were incorrectly swapped. Fix the assignment
logic so the correct LED is illuminated for the LAN LEDs.
Signed-off-by: David Bauer <mail@david-bauer.net>
Felix Fietkau [Wed, 20 Sep 2023 16:40:17 +0000 (18:40 +0200)]
hostapd: add missing NULL pointer check in uc_hostapd_iface_stop
Avoid crashing if the interface has already been removed
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Andreas Böhler [Sat, 9 Sep 2023 20:54:01 +0000 (22:54 +0200)]
ipq4019: add support for ZTE MF282 Plus aka DreiTube
The ZTE MF282 Plus is a LTE router used (exclusively?) by the network
operator "3". It is very similar to the MF286/MF287 but in the form factor
of the MF282.
Specifications
==============
SoC: IPQ4019
RAM: 256MiB
Flash: 8MiB SPI-NOR + 128MiB SPI-NAND
LAN: 1x GBit LAN
LTE: ZTE Cat6
WiFi: 802.11a/b/g/n/ac SoC-integrated
MAC addresses
=============
LAN: from config
WiFi 1: from config + 1
WiFi 2: from config + 2
Installation
============
Option 1 - TFTP
---------------
TFTP installation using UART is preferred. Disassemble the device and
connect serial. Put the initramfs image as openwrt.bin to your TFTP server
and configure a static IP of 192.168.1.100. Load the initramfs image by
typing:
setenv serverip 192.168.1.100
setenv ipaddr 192.168.1.1
tftpboot 0x84000000 openwrt.bin
bootm 0x84000000
From this intiramfs boot you can take a backup of the currently installed
partitions as no vendor firmware is available for download:
ubiattach -m9
cat /dev/ubi0_0 > /tmp/ubi0_0
cat /dev/ubi0_1 > /tmp/ubi0_1
Copy the files /tmp/ubi0_0 and /tmp/ubi0_1 somewhere save.
Once booted, transfer the sysupgrade image and run sysupgrade. You might
have to delete the stock volumes first:
ubirmvol /dev/ubi0 -N ubi_rootfs
ubirmvol /dev/ubi0 -N kernel
Option 2 - From stock firmware
------------------------------
The installation from stock requires an exploit first. The exploit consists
of a backup file that forces the firmware to download telnetd via TFTP from
192.168.0.22 and run it. Once exploited, you can connect via telnet and
login as admin:admin.
The exploit will be available at the device wiki page.
Once inside the stock firmware, you can transfer the -factory.bin file to
/tmp by using "scp" from the stock frmware or "tftp".
ZTE has blocked writing to the NAND. Fortunately, it's easy to allow write
access - you need to read from one file in /proc. Once done, you need to
erase the UBI partition and flash OpenWrt. Before performing the operation,
make sure that mtd9 is the partition labelled "rootfs" by calling
"cat /proc/mtd".
Complete commands:
cd /tmp
tftp -g -r factory.bin 192.168.0.22
cat /proc/driver/sensor_id
flash_erase /dev/mtd9 0 0
dd if=/tmp/factory.bin of=/dev/mtdblock9 bs=131072
Afterwards, reboot your device and you should have a working OpenWrt
installation.
Restore Stock
=============
Option 1 - via UART
-------------------
Boot an OpenWrt initramfs image via TFTP as for the initial installation.
Transfer the two backed-up files to your box to /tmp.
Then, run the following commands - replace $kernel_length and $rootfs_size
by the size of ubi0_0 and ubi0_1 in bytes.
ubiattach -m 9
ubirmvol /dev/ubi0 -N kernel
ubirmvol /dev/ubi0 -N rootfs
ubirmvol /dev/ubi0 -N rootfs_data
ubimkvol /dev/ubi0 -N kernel -s $kernel_length
ubimkvol /dev/ubi0 -N ubi_rootfs -s $rootfs_size
ubiupdatevol /dev/ubi0_0 /tmp/ubi0_0
ubiupdatevol /dev/ubi0_1 /tmp/ubi0_1
Option 2 - from within OpenWrt
------------------------------
This option requires to flash an initramfs version first so that access
to the flash is possible. This can be achieved by sysupgrading to the
recovery.bin version and rebooting. Once rebooted, you are again in a
default OpenWrt installation, but no partition is mounted.
Follow the commands from Option 1 to flash back to stock.
LTE Modem
=========
The LTE modem is similar to the MF286R, it provides an RNDIS interface
and an AT interface.
Other Notes
===========
There is one GPIO Switch "Power button blocker" which, if enabled, does not
trigger a reset of the SoC if the modem reboots. If disabled, the SoC is
rebooted along with the modem. The modem can be rebooted via the exported
GPIO "modem-reset" in /sys/class/gpio.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
John Audia [Tue, 19 Sep 2023 19:04:14 +0000 (15:04 -0400)]
kernel: bump 5.15 to 5.15.132
Changelog: https://cdn.kernel.org/pub/linux/kernel/v5.x/ChangeLog-5.15.132
Removed upstreamed:
bcm53xx/patches-5.15/037-v6.6-0006-ARM-dts-BCM53573-Add-cells-sizes-to-PCIe-node.patch[1]
bcm53xx/patches-5.15/037-v6.6-0007-ARM-dts-BCM53573-Use-updated-spi-gpio-binding-proper.patch[2]
bcm53xx/patches-5.15/037-v6.6-0008-ARM-dts-BCM5301X-Extend-RAM-to-full-256MB-for-Linksy.patch[3]
All other patches automatically rebased.
1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.132&id=
b35f3ca1877e024887df205ede952863d65dad36
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.132&id=
2840d9b9c8750be270fb1153ccd5b983cbb5d592
3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.132&id=
f086e859ddc252c32f0438edff241859c0f022ce
Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3
Signed-off-by: John Audia <therealgraysky@proton.me>
Felix Fietkau [Wed, 20 Sep 2023 11:43:14 +0000 (13:43 +0200)]
hostapd: fix a crash when disabling an interface during channel list update
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Alexander Couzens [Mon, 18 Sep 2023 22:23:40 +0000 (00:23 +0200)]
toolchain: assign PKG_CPE_ID
The PKG_CPE_ID links to NIST CPE version 2.2.
Assign PKG_CPE_ID to all remaining package which have a CPE ID.
Not every package has a CPE id.
Related: https://github.com/openwrt/packages/issues/8534
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Alexander Couzens [Mon, 18 Sep 2023 22:10:03 +0000 (00:10 +0200)]
tools: assign PKG_CPE_ID
The PKG_CPE_ID links to NIST CPE version 2.2.
Assign PKG_CPE_ID to all remaining tools which have a CPE ID.
Not every tool has CPE id.
Related: https://github.com/openwrt/packages/issues/8534
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Alexander Couzens [Mon, 18 Sep 2023 20:53:14 +0000 (22:53 +0200)]
packages: assign PKG_CPE_ID for all missing packages
The PKG_CPE_ID links to NIST CPE version 2.2.
Assign PKG_CPE_ID to all remaining package which have a CPE ID.
Not every package has CPE id.
Related: https://github.com/openwrt/packages/issues/8534
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
John Audia [Thu, 3 Aug 2023 18:18:49 +0000 (14:18 -0400)]
sdk: add cpupower to userspace sources
For https://github.com/openwrt/packages/pull/21533 to be merged,
this source tree is needed to be included.
Signed-off-by: John Audia <therealgraysky@proton.me>
Robert Marko [Thu, 3 Aug 2023 11:16:05 +0000 (13:16 +0200)]
mvebu: eDPU: add support for version with external switch
New revision of eDPU uses an Marvell MV88E6361 switch to connect the SFP
cage and G.hn IC instead of connecting them directly to the ethernet
controllers.
The same image can be used on both versions as U-Boot will enable the
switch node and disable the unused ethernet controller.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Robert Marko [Fri, 18 Aug 2023 10:22:29 +0000 (12:22 +0200)]
uboot-mvebu: eDPU: add support for version with external switch
New revision of eDPU uses an Marvell MV88E6361 switch to connect the SFP
cage and G.hn IC instead of connecting them directly to the ethernet
controllers.
In order to use the same image for both boards, U-Boot is responsible for
detecting the revision and enabling/disabling DTS nodes.
So, to make it easy for users, lets add the pending U-Boot patches to build
in OpenWrt.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Robert Marko [Fri, 4 Aug 2023 12:39:18 +0000 (14:39 +0200)]
generic: 6.1: backport support for Marvell
88E6361 switch
New revision of Methode eDPU boards uses Marvell
88E6361 switch, so lets
backport it from kernel 6.5.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Robert Marko [Thu, 14 Sep 2023 10:44:02 +0000 (12:44 +0200)]
generic: 5.15: backport support for Marvell
88E6361 switch
New revision of Methode eDPU boards uses Marvell
88E6361 switch, so lets
backport it from kernel 6.5.
Since 5.15 doesnt have phylink_get_caps I had to modify the backport to
use the old mv88e6393x_phylink_validate instead.
I had to fixup one more instance of port_max_speed_mode as well that is not
present in 6.5.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Felix Fietkau [Tue, 19 Sep 2023 09:46:16 +0000 (11:46 +0200)]
netifd: update to the latest version
7a58b995fdbe wireless: update prev_config on SET_DATA notify
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Tue, 19 Sep 2023 09:02:54 +0000 (11:02 +0200)]
hostapd: use phy name for hostapd interfaces instead of first-bss ifname
Improves reliability in error handling
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Andreas Böhler [Mon, 18 Sep 2023 10:08:18 +0000 (12:08 +0200)]
ipq40xx: ZTE MF287 series: move to gpio-export for modem-reset GPIO
Turn the "gpio-restart" node into a "gpio-export" node for all MF287
variants, similar to the MF287 Pro. Unfortunately, there doesn't seem to be
a "power button blocker" GPIO for the MF287 and MF287 Plus, so a modem
reset always triggers a system reset.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
Andreas Böhler [Sat, 16 Sep 2023 19:55:01 +0000 (21:55 +0200)]
ipq40xx: refactor ZTE MF287 series
The ZTE MF287 requires a different board calibration file for ath10k than
the ZTE MF287+. The two devices receive their own DTS, thus the device tree
is slightly refactored.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
Pascal Coudurier [Sun, 20 Aug 2023 13:07:34 +0000 (15:07 +0200)]
x86: add 6.1 testing kernel
Enable building with 6.1 as testing kernel
Compile-tested: x86_64, x86_generic, x86_legacy, x86_geode
Run-tested: x86_64, x86_generic (qemu), x86_legacy (qemu)
Signed-off-by: Pascal Coudurier <coudu@gmx.com>
Pascal Coudurier [Wed, 23 Aug 2023 20:45:31 +0000 (22:45 +0200)]
kernel: modules: video: adapt drm-amdgpu and drm-radeon for kernel 6.1
Package and add dependencies to drm-amdgpu and drm-radeon for 6.1
* package acpi-video, drm-display-helper and drm-buddy
* add acpi-video, drm-display-helper and drm-buddy as dependencies for
drm-amdgpu
* add acpi-video and drm-display-helper as dependencies for drm-radeon
Signed-off-by: Pascal Coudurier <coudu@gmx.com>
Pascal Coudurier [Mon, 21 Aug 2023 19:19:51 +0000 (21:19 +0200)]
kernel: modules: netdevices: adapt mlx5-core for kernel 6.1
Set CONFIG_MLX5_VFIO_PCI=n for kernel greater than 5.18
Signed-off-by: Pascal Coudurier <coudu@gmx.com>
Pascal Coudurier [Sun, 20 Aug 2023 13:12:16 +0000 (15:12 +0200)]
kernel: modules: hwmon: adapt nct6775 for kernel 6.1
nct6775 module splited in 5.19 kernel:
* add nct6775-core module @ge5.19
* add regmap dependency for 6.1
Signed-off-by: Pascal Coudurier <coudu@gmx.com>
Pascal Coudurier [Mon, 21 Aug 2023 12:23:13 +0000 (14:23 +0200)]
x86: refresh kernel configs for 6.1
refresh and add missing symbols for target and subtargets
Signed-off-by: Pascal Coudurier <coudu@gmx.com>
Pascal Coudurier [Sun, 20 Aug 2023 13:01:31 +0000 (15:01 +0200)]
x86: copy 5.15 configs to 6.1
Copy 5.15 configs to 6.1 as a starting point
Signed-off-by: Pascal Coudurier <coudu@gmx.com>
Pascal Coudurier [Sun, 20 Aug 2023 12:54:22 +0000 (14:54 +0200)]
x86: refresh patches for 6.1
Removed upstream merged patch:
113-v5.21-platform-x86-pmc_atom-Add-Lex-3I380NX-industrial-PC-.patch
Manually rebased:
103-pcengines_apu6_platform.patch
Signed-off-by: Pascal Coudurier <coudu@gmx.com>
Pascal Coudurier [Sun, 20 Aug 2023 12:48:42 +0000 (14:48 +0200)]
x86: copy 5.15 patches to 6.1
Copy existing patches from 5.15 to 6.1
Signed-off-by: Pascal Coudurier <coudu@gmx.com>
Zoltan HERPAI [Sun, 13 Aug 2023 00:29:06 +0000 (02:29 +0200)]
sunxi: add support for Bananapi P2 Zero
CPU: Allwinner H2+ quad-core Cortex-A7 @ 1.2GHz
Memory: 512Mb DDR3
Storage: SDcard, 8GB eMMC
Network: 10/100M ethernet, optional PoE support, Ampak AP6212 wifi + BT
USB: 1x USB 2.0 OTG
Other: 40-pin expansion header, mini-HDMI
Flashing instructions:
Standard sunxi SD card installation procedure - copy image to SD card,
insert into SD card slot on the device and boot.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Felix Fietkau [Mon, 18 Sep 2023 14:50:35 +0000 (16:50 +0200)]
hostapd: fix dynamically adding interfaces with 802.11ax support disabled in the build
Move an important code line outside of #ifdef CONFIG_IEEE80211AX
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Christian Marangi [Mon, 18 Sep 2023 11:43:59 +0000 (13:43 +0200)]
sunxi: refresh kernel patches
Refresh kernel patches for sunxi target.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Felix Fietkau [Mon, 18 Sep 2023 10:46:12 +0000 (12:46 +0200)]
mt76: update to the latest version
b5d13611d35e mt76: mt7915: fix monitor mode issues
bbbac7deee3d wifi: mt76: rename mt76_packet_id_init/flush to mt76_wcid_init/cleanup
f1e1e67d97d1 wifi: mt76: fix race condition related to checking tx queue fill status
b3f739a64e6b wifi: mt76: mt7996: add eht rx rate support
ca4917062f17 wifi: mt76: mt76x0: remove dead code in mt76x0_phy_get_target_power
325a0c493199 wifi: mt76: mt7996: fill txd by host driver
cd371fcc98d4 mt76: mt7996: sync with upstream
d71f8d1b172b wifi: mt76: use atomic iface iteration for pre-TBTT work
8d5ea32d4895 wifi: mt76: remove unused error path in mt76_connac_tx_complete_skb
01860c02c505 wifi: mt76: add DMA mapping error check in mt76_alloc_txwi()
62ddb6d46a97 wifi: mt76: connac: introduce helper for mt7925 chipset
0837f37e998b wifi: mt76: mt792x: support mt7925 chip init
899ff378082b wifi: mt76: connac: export functions for mt7925
c3858b5bf347 wifi: mt76: connac: add eht support for phy mode config
5df6b26a9fc5 wifi: mt76: connac: add eht support for tx power
a8081345c636 wifi: mt76: connac: add data field in struct tlv
9b38aebecf78 wifi: mt76: connac: add more unified command IDs
84984e6dc87d wifi: mt76: connac: add more unified event IDs
6fe92398c9ce wifi: mt76: mt7996: set correct wcid in txp
2cfe2fb0bb80 wifi: mt76: mt7996: fix beamform mcu cmd configuration
e512241bb5bb wifi: mt76: mt7996: fix beamformee ss subfield in EHT PHY cap
719a98f832c7 wifi: mt76: mt7996: fix wmm queue mapping
9723562f2a5b wifi: mt76: mt7996: fix rx rate report for CBW320-2
1bb5a6a54943 wifi: mt76: mt7996: fix TWT command format
751b054891f6 wifi: mt76: mt7996: only set vif teardown cmds at remove interface
fea1e10c7741 wifi: mt76: mt7996: support more options for mt7996_set_bitrate_mask()
d497ee8aa2f5 wifi: mt76: mt7996: support per-band LED control
8ccc84111141 wifi: mt76: Use PTR_ERR_OR_ZERO() to simplify code
161f70217edf wifi: mt76: mt7921e: Support MT7992 IP in Xiaomi Redmibook 15 Pro (2023)
7d25bfc3f0cc wifi: mt76: fix clang-specific fortify warnings
5971aa968401 wifi: mt76: connac: add MBSSID support for mt7996
5a47dd323be1 wifi: mt76: update beacon size limitation
d5b4b81dcc9e wifi: mt76: check sta rx control frame to multibss capability
af0e1f6dafb5 wifi: mt76: fix potential memory leak of beacon commands
65d91a833b01 wifi: mt76: get rid of false alamrs of tx emission issues
29411e52059f wifi: mt76: fix per-band IEEE80211_CONF_MONITOR flag comparison
4da62774038a wifi: mt76: check vif type before reporting cca and csa
4a85678fe089 wifi: mt76: mt7915: update mpdu density capability
791a45cffadf wifi: mt76: mt7915: fix beamforming availability check
08e1e6cb7d41 wifi: mt76: Drop unnecessary error check for debugfs_create_dir()
d1881b1b2bf6 wifi: mt76: move struct ieee80211_chanctx_conf up to struct mt76_vif
66d5694e1898 wifi: mt76: mt7921: fix the wrong rate pickup for the chanctx driver
9fc37b0ac546 wifi: mt76: mt7921: fix the wrong rate selected in fw for the chanctx driver
2afc7285f75d wifi: mt76: mt7925: add Mediatek Wi-Fi7 driver for mt7925 chips
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Mon, 18 Sep 2023 10:50:45 +0000 (12:50 +0200)]
mac80211: backport upstream patch required for mt76 update
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Chukun Pan [Wed, 3 May 2023 15:18:48 +0000 (23:18 +0800)]
ipq40xx: add support for YYeTs LE1
Hardware Highlights:
SoC: Qualcomm IPQ4019 717 MHz
RAM: 512M NT5CC256M16ER-EK
Flash: 32M SPI NOR MX25L25635F
WIFI1: 2.4 GHz 2T2R integrated
WIFI2: 5 GHz 2T2R integrated
Ethernet: QCA8075 (4x LAN, 1x WAN)
LEDS: power, wlan2g, wlan5g, usb
USB: 1x 3.0
Button: Reset
Installation:
Upload factory.bin in stock firmware's upgrade
page, and this will take a few minutes.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Chukun Pan [Sun, 17 Sep 2023 15:18:05 +0000 (23:18 +0800)]
ipq-wifi: update to version 2023-09-16
Contains following updates:
* ipq8074: add Asus RT-AX89X BDF
* ipq8074: update RegDB in new submitted BDF
* ipq40xx: add YYeTs LE1 BDF
* ipq8074: add Netgear WAX620
* qca-wireless: ipq40xx: add BDFs for ZTE MF287
* ipq8174: Add Linksys MX4200
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Andreas Böhler [Tue, 12 Sep 2023 17:57:55 +0000 (19:57 +0200)]
ipq40xx: fix image building for ZTE MF287 series
For the ZTE MF287 series, a special recovery image is built. The Makefile
worked fine on snapshot, but created corrupt images on the 23.05 images.
By using the appropriate variable, this should be fixed.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
Zoltan HERPAI [Fri, 1 Sep 2023 22:18:18 +0000 (00:18 +0200)]
sunxi: add support for H616 SoC and Orangepi Zero 2
Specifications:
SoC: Allwinner H616 @ 1.5 Ghz
DRAM: 1Gb LPDDR3
Power: 5V USB-C
Video: HDMI (Type 2.0A - micro)
Network: 10/100/1000Mbps Ethernet (Realtek RTL8211F), AW859A BT+wifi
Storage: microSD / 2Mb SPI flash
USB: 1 USB2.0 Host
Debug Serial UART
Flashing instructions:
Standard sunxi SD card installation procedure - copy image to SD card,
insert into SD card slot on the device and boot.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Max Qian [Fri, 15 Sep 2023 04:54:30 +0000 (21:54 -0700)]
ramips: RT1800: fix invalid octal number error
This commit removes the padded zeros in the date formatting.
The padded zeros from the date command causes the numbers
to be interpreted as an octal number by printf. Months, days,
and years with the number 08 or 09 raise an error in printf as an
"invalid octal number" and get interpreted as a zero.
Signed-off-by: Max Qian <public@maxqia.com>
Robert Marko [Sun, 17 Sep 2023 20:19:23 +0000 (22:19 +0200)]
ipq40xx: 6.1: add missing secure QFPROM symbol
Kernel config for 6.1 on ipq40xx is missing the config for
CONFIG_NVMEM_QCOM_SEC_QFPROM which them makes the build stop with a prompt.
Symbol is there in 5.15 config but 6.1 config was based of a version that
does not yet have it set as it was introduced after the 6.1 PR.
So, disable CONFIG_NVMEM_QCOM_SEC_QFPROM to fix building on 6.1.
Fixes: 825cfa4e36cb ("ipq40xx: 6.1: refresh kernel config")
Signed-off-by: Robert Marko <robimarko@gmail.com>
Robert Marko [Mon, 14 Aug 2023 10:08:07 +0000 (12:08 +0200)]
ipq40xx: add 6.1 as testing kernel
Allow selecting 6.1 as the testing kernel.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Robert Marko [Mon, 14 Aug 2023 16:49:37 +0000 (18:49 +0200)]
ipq40xx: 6.1: refresh kernel config
Refresh the kernel config via make kernel_menuconfig.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Robert Marko [Mon, 21 Aug 2023 21:42:54 +0000 (23:42 +0200)]
ipq40xx: 6.1: use latest DSA and ethernet patches
This pulls-in the latest version of qca8k based IPQ4019 driver as well as
the latest version of IPQESS that was sent upstream.
Both qca8k and IPQESS have been improved and cleaned up compared to current
version of patches.
PSGMII PHY mode and missing reset have been upstreamed and will be in
the kernel 6.6.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Robert Marko [Mon, 14 Aug 2023 16:45:59 +0000 (18:45 +0200)]
ipq40xx: 6.1: adapt and refresh patches
Adapt and refresh patches to apply.
DSA and ethernet driver patches are dropped as they will be replaced with
the latest version that was sent upstream.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Robert Marko [Mon, 14 Aug 2023 16:42:18 +0000 (18:42 +0200)]
ipq40xx: qca807x: adapt for 6.1
Kernel 6.1 has changed format of sfp_parse_support(), so lets adapt to
those changes so it works on newer kernels as well.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Robert Marko [Mon, 14 Aug 2023 11:16:12 +0000 (13:16 +0200)]
ipq40xx: copy 5.15 patches and config to 6.1
Copy the 5.15 patches and config as a base for 6.1 support.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Robert Marko [Mon, 14 Aug 2023 11:06:27 +0000 (13:06 +0200)]
ipq40xx: update ESS reset patch with pending upstream
Use the split version of ESS reset patch that was sent upstream.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Robert Marko [Mon, 14 Aug 2023 10:56:49 +0000 (12:56 +0200)]
ipq40xx: move DSA and ethernet driver to 5.15 specific directory
As a preparation to move to 6.1, we need to move the DSA and ethernet
drivers to a 5.15 specific directory as 6.1 will use the latest patchset
that was sent upstream which is too hard to backport to 5.15.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Matthijs Kooijman [Thu, 31 Aug 2023 19:10:23 +0000 (21:10 +0200)]
ath79: fix packetloss on some WLR-7100
On some WLR-7100 routers, significant packet loss was observed. This is
fixed by configuring a delay on the GMAC0 RXD and RXDV lines.
The values used in this commit are copied from the values used by the
stock firmare (based on register dumping).
Out of four test routers, the problem was consistently observed on two.
It is unclear what the relevant difference is exactly (the two working
routers were v1 001 with AR1022 and v1 002 with AR9342, the two broken
routers were both v1 002 with AR1022). All PCB routing also seems
identical, so maybe there is some stray capacitance on some of these
that adds just enough delay or so...
With this change, the packet loss disappears on the broken routers,
without introducing new packet loss on the previously working routers.
Note that the PHY *also* has delays enabled (through
`qca,ar8327-initvals`) on both RX and TX lines, but apparently that is
not enough, or it is not effective (registers have been verified to be
written).
For detailed discussion of this issue and debug history, see
https://forum.openwrt.org/t/sitecom-wlr-7100-development-progress/79641
Signed-off-by: Matthijs Kooijman <matthijs@stdin.nl>
Robert Marko [Sat, 16 Sep 2023 10:02:50 +0000 (12:02 +0200)]
mac80211: ath11k: sync with ath-next
Synchronize the ath11k backports with the current ath-next tree.
All of the changes are various bugfixes, there is no new major feature.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Robert Marko [Sat, 16 Sep 2023 09:26:35 +0000 (11:26 +0200)]
mac80211: ath11k: drop upstreamed patches
Commit
ed3725e15a154ebebf44e0c34806c57525483f92
("wifi: ath11k: Fix qmi_msg_handler data structure initialization")
has been present upstream since 6.1.2 but it seems Quilt refreshed it
wrongly so it appeared like a completely different patch.
Commit
7c15430822e71e90203d87e6d0cfe83fa058b0dc
("wifi: ath11k: allow system suspend to survive ath11k")
has been present upstream since 6.1.16 but somehow quilt still happily
applied it.
So, drop both of them.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Zoltan HERPAI [Sat, 16 Sep 2023 15:52:57 +0000 (17:52 +0200)]
sunxi: use kernel 6.1 as default
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Erik Karlsson [Wed, 6 Sep 2023 10:33:17 +0000 (12:33 +0200)]
procd: create /dev/fd symlink
This is needed for ksh/bash style process substitution such as
<(command) and >(command) which was introduced in ash as of busybox
version 1.34.0 to work.
Signed-off-by: Erik Karlsson <erik.karlsson@genexis.eu>
Roger Pueyo Centelles [Wed, 2 Jun 2021 16:45:30 +0000 (18:45 +0200)]
ath79: add support for MikroTik RouterBOARD 750 r2 (hEX lite)
This patch adds support for the MikroTik RouterBOARD 750 r2, marketed as
hEX lite, a small indoor router with 5x 10/100 Mbps Ethernet ports, one
with PoE in. The device was already supported by the ar71xx target.
Specifications:
- SoC: Qualcomm Atheros QCA9533
- Flash: 16 MB SPI NOR
- RAM: 64 MB
- Ethernet: 4x 10/100 Mbps LAN, 1x 10/100 Mbps WAN (PoE in)
- LEDs: 5x Ethernet port activity (green), 1x user (green)
- Buttons: 1x reset
See https://mikrotik.com/product/RB750r2 for more details.
Not working:
- Serial port (already not working in ar71xx)
Flashing:
TFTP boot initramfs image and then perform sysupgrade. Only the
"Internet" port will ask for an initramfs image. Follow common
MikroTik procedure as in https://openwrt.org/toh/mikrotik/common.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Hannu Nyman [Wed, 13 Sep 2023 13:49:03 +0000 (16:49 +0300)]
scripts/download.pl: Remove stale download sites and convert to https
Remove the stale site definitions from @APACHE, KERNEL etc.
* Remove site that had dropped APACHE
* Remove KERNEL site leading to wrong directory
* Remove dead sites
* Convert ftp/http URLs to https, if possible. Remove duplicate
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Thomas Makin [Tue, 5 Sep 2023 00:00:14 +0000 (20:00 -0400)]
ipq40xx: add support for Netgear RBX40
This adds support for the RBR40 and RBS40 (sold together as RBK40),
two netgear routers identical to SRR60/SRS60 in all but antennae (and
hardware id). See
2cb24b3f3c for details.
Signed-off-by: Thomas Makin <halorocker89@gmail.com>
Felix Fietkau [Fri, 15 Sep 2023 18:40:59 +0000 (20:40 +0200)]
netifd: update to the latest version
88a3a9e2be07 wireless: clean up prev_config handling
afcd3825dad9 wireless: dynamically enable/disable virtual interfaces base on network interface autostart
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Fri, 15 Sep 2023 18:38:45 +0000 (20:38 +0200)]
hostapd: add missing ubus ACL entries for AP+client (#13449)
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Fri, 15 Sep 2023 12:25:23 +0000 (14:25 +0200)]
hostapd: support dynamic reload of vlan files when renaming interfaces
Avoids unnecessary AP restart on ifname changes when wifi-vlan sections
are present.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Fri, 15 Sep 2023 11:10:27 +0000 (13:10 +0200)]
netifd: update to the latest version
3d425f16d6a6 wireless: rework and fix vlan/station config reload handling
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Daniel Maslowski [Thu, 14 Sep 2023 19:56:58 +0000 (21:56 +0200)]
kernel: decouple 9P virtio from 9P net
General support for 9P is desirable on platforms without virtualization.
This decouples the 9P general networking support for use on more platforms.
Signed-off-by: Daniel Maslowski <info@orangecms.org>
Arne Zachlod [Wed, 13 Sep 2023 16:20:03 +0000 (18:20 +0200)]
toolchain: musl: add PKG_CPE_ID
Vulnerabilities of musl libc are tracked as
cpe:/a:musl-libc:musl
Signed-off-by: Arne Zachlod <arne@nerdkeller.org>
Felix Fietkau [Thu, 14 Sep 2023 17:08:34 +0000 (19:08 +0200)]
hostapd: fix more AP+STA issues
When STA is disconnected, ensure that the interface is in a cleanly stopped
state:
- if in regular enable/disable state, stop beacons if necessary
- in any other state, disable the interface
When the STA is up, ignore repeated start commands for the same channel, in
order to avoid unnecessary AP restarts
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Thu, 14 Sep 2023 11:35:17 +0000 (13:35 +0200)]
hostapd: fix more dynamic reload issues
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Thu, 14 Sep 2023 11:28:14 +0000 (13:28 +0200)]
mac80211: fix AP reconfiguration on DFS channels in non-ETSI regdomain
Allow grace period for DFS available after shutting down beacons on the channel
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Wed, 13 Sep 2023 20:57:47 +0000 (22:57 +0200)]
hostapd: add missing return statement
Avoids crash due to uninitialized stack/register garbage
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Wed, 13 Sep 2023 09:00:53 +0000 (11:00 +0200)]
mac80211: only add the mbssid option to the config when set
This avoids errors when the feature is not built into the hostapd binary
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Wed, 13 Sep 2023 15:07:17 +0000 (17:07 +0200)]
hostapd: do not modify hapd->started when stopping an AP
It can cause cleanup to be skipped on wifi restart, which can lead to
use-after-free bugs
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Wed, 13 Sep 2023 09:00:53 +0000 (11:00 +0200)]
hostapd: update to the latest version
8e6485a1bcb0 PEAP client: Update Phase 2 authentication requirements
de9a11f4dde9 TTLS client: Support phase2_auth=2
b2a1e7fe7ab9 tests: PEAP and TTLS phase2_auth behavior
518ae8c7cca8 P2P: Do not print control characters in debug
a4c133ea73c7 WPS: Optimize attribute parsing workaround
7a37a94eaa0d Check whether element parsing has failed
f80d83368818 ACS: Remove invalid debug print
fb2b7858a728 FILS: Fix HE MCS field initialization
50ee26fc7044 P2P: Check p2p_channel_select() return value
a50d1ea6a2b3 Add QCA vendor attributes for user defined power save parameters
4636476b7f22 Set RRM used config if the (Re)Association Request frame has RRM IE
e53d44ac63e8 AP MLD: Use STA assoc link address in external auth status to the driver
99a96b2f9df7 AP MLD: OWE when SME is offloaded to the driver
96deacf5d710 nl80211: Skip STA MLO link channel switch handling in AP mode
d320692d918a AP MLD: Handle new STA event when using SME offload to the driver
faee8b99e928 tests: Fix eht_mld_sae_legacy_client to restore sae_pwe
c3f465c56c94 wlantest: Handle variable length MIC field in EAPOL-Key with OWE
605034240e0c wlantest: Support multiple input files
053bd8af8ed2 Recognize FTE MLO subelements
43b5f11d969a Defragmentation of FTE
3973300b8ded FTE protected element check for MLO Reassociation Response frame
74e4a0a6f1e4 wlantest: Learn AP MLD MAC address from Beacon frames
a5a0b2cf7b1b wlantest: Find non-AP MLD only from affiliated BSSs of the AP MLD
74472758584d wlantest: Recognize non-AP MLD based on any link address for decryption
1ffabd697c67 wlantest: Learn non-AP MLD MAC address from (Re)Association Request frames
4e8e515f92b9 wlantest: Use MLO search for the STA in reassociation
49bf9f2df95a wlantest: Use the MLD MAC address as well for matching STA entries
5434a42ec69c wlantest: Search for FT Target AP using MLD MAC address as well
a19fcf685cae wlantest: Include the MLD MAC address of the AP MLD in new-STA prints
709d46da73da wlantest: Do not claim update to AP MD MAC address if no change
770760454f9e wlantest: Do not update BSS entries for other AP MLDs in PTK cloning
084745ffc508 Add QCA vendor attributes for NDP setup
bf9cbb462fd9 Fix writing of BIGTK in FT protocol
011775af9443 tests: Check for beacon loss when using beacon protection
8f148d51322f Fix a compiler warning on prototype mismatch
b7db495ad9c9 AP: Fix ieee802_1x_ml_set_sta_authorized()
232667eafe0d Fix CCMP test vector issues
30771e6e05ed Include PTID in PV1 nonce construction for CCMP test vector
34841cfd9aba Minor formatting changes to CCMP test vectors
a685d84139e6 BSS coloring: Fix CCA with multiple BSS
bc0636841a70 wpa_supplicant: Fix configuration parsing error for tx_queue_*
2763d1d97e66 hostapd: Fix AID assignment in multiple BSSID
763a19286e2f AP: Add configuration option to specify the desired MLD address
bd209633eb10 AP: Use is_zero_ether_addr() to check if BSSID is NULL
bc0268d053b4 wlantest: Guess SAE/OWE group from EAPOL-Key length mismatch
a94ba5322803 EHT: Support puncturing for 320 MHz channel bandwidth
7e1f5c44c97e EHT: 320 MHz DFS support
6f293b32112a QCA vendor attributes for updating roaming AP BSSID info
5856373554eb Extend QCA vendor command to include more parameters for netdev events
e080930aa0a5 Define QCA vendor roam control RSSI attributes
fe72afe713ad Define QCA vendor attribute for high RSSI roam trigger threshold
47a65ccbfde2 P2P: Clean wpa_s->last_ssid when removing a temporary group network
884125ab7d21 tests: P2P autonomous GO and clearing of networking information
7637d0f25053 P2P: Do not filter pref_freq_list if the driver does not provide one
dd1330b502ff Fix hostapd interface cleanup with multiple interfaces
0a6842d5030e nl80211: Fix beacon rate configuration for legacy rates 36, 48, 54 Mbps
d606efe054d5 tests: Beacon rate configuration for 54 Mbps
f91d10c0e6aa tests: Update RSA 3k certificates
07d3c1177bbb tests: Make sae_proto_hostapd_status_* more robust
1085e3bdc6f6 Update iface->current_mode when fetching new hw_features
338a78846b44 Add a QCA vendor sub command for transmit latency statistics
9318db7c38bc wlantest: Use local variables for AA/SPA in FT Request/Response processing
628b9f10223d wlantest: Derive PMK-R1 and PTK using AA/SPA for MLO FT over-the-DS
104aa291e5c8 wlantest: Fix FT over-the-DS decryption
37c87efecfe3 wlantest: Search SPA using MLO aware find for FT Request/Response frame
19f33d7929e8 wlantest: Learn the Link ID for AP MLD affiliated BSSs
6ae43bb10323 wlantest: Learn link address for assoc link from (Re)Association Request
4c079dcc64da Increment hmac_sha*_vector() maximum num_elem value to 25
e6f64a8e1daf FT: FTE MIC calculation for MLO Reassociation Request frame
a83575df5994 wlantest: FTE MIC calculation for MLO Reassociation Request frames
ff02f734baf8 wlantest: Allow specific link BSS to be found with bss_find_mld()
7381c60db8f0 FT: Make FTE MIC calculation more flexible
ac9bf1cc2a4c Decrement hmac_sha*_vector() maximum num_elem value to 11
aa08d9d76803 Fix use of defragmented FTE information
78b153f90a74 Calculate defragmented FTE length during IE parsing
8cf919ffd5c4 wlantest: FTE MIC calculation for MLO Reassociation Response frame
d12a3dce82a9 wlantest: Store and check SNonce/ANonce for FT Authentication
20febfd7838d wlantest: Dump MLO association information in debug
609864d6a8a1 Add QCA vendor attribute to configure MLD ID in ML probe request
12154861e24a Add support for conversion to little endian for 24 bits
c437665041c0 Add Non EHT SCS Capability in (Re)Association Request frames
33da386553b7 SCS: Add support for QoS Characteristics in SCS request
edfca280cbe8 SCS: Add support for optional QoS Charateristics parameters
32dcec9529ec Send actual MFP configuration when driver takes care of BSS selection
123d16d860fa Update hw_mode when CSA finishes
b3d852560bda Change QCA vendor configure attribution name of peer MAC address
12fabc4765c2 Add QCA vendor attribute for configuring max A-MPDU aggregation count
f6eaa7b729cb Add QCA vendor attribute for TTLM negotiation support type
f6dcd326fea7 wlantest: Indicate ToDS/FromDS values for BSS DATA entries
6ce745bb87d4 wlantest: MLO support for decrypting 4-address frames
850dc1482953 wlantest: Remove duplicated A1/A2/A3 override detection for MLO
770e5a808fbb wlantest: Determine whether A1 points to STA once in rx_data_bss_prot()
377d617b574a Define new BSS command info mask for AP MLD address
d3ab6e001f62 wlantest: Use non-AP MLD's MLD MAC address in FT over-the-air derivation
a845601ffe32 wlantest: Derive PTK in MLO using MLD MAC addresses for FT over-the-air
0cd2bfc8a402 wlantest: Fix FTE MIC calculation for MLO Reassociation Response frames
528abdeb673b wlantest: Learn group keys from MLO FT Reassociation Response frames
990600753dd9 wlantest: Defragment Basic MLE before processing
de043ec01ab5 wlantest: Defragment the Per-STA Profile subelement
bae1ec693c44 wlantest: Minimal parsing of Basic MLE STA Profile
ba1579f3bf7c Clear BIGTK values from wpa_supplicant state machine when not needed
b46c4b9a916a tests: Beacon protection and reconnection
3e71516936b7 Document per-ESS MAC address (mac_addr=3 and mac_value)
f85b2b2dee3b Extend wpa_parse_kde_ies() to include EHT capabilities
e3a68081bc1e driver: Add option for link ID to be specified for send_tdls_mgmt()
c7561502f2e8 nl80211: Use a QCA vendor command to set the link for TDLS Discovery Response
a41c8dbdd84e TDLS: Copy peer's EHT capabilities
626501434be1 TDLS: Learn MLD link ID from TDLS Discovery Response
5f30f62eead7 TDLS: Reply to Discovery Request on the link with matching BSSID
940ef9a05c0f TDLS: Use link-specific BSSID instead of sm->bssid for MLO cases
f429064189c3 TDLS: Set EHT/MLO information for TDLS STA into the driver
dd25885a9daa Remove space-before-tab in QCA vendor related definitions
af6e0306b2a9 Fix typos in QCA vendor related definitions
4c9af238c1e4 Fix inconsistent whitespace use in QCA vendor related definitions
e5ccbfc69ecf Split long comment lines in QCA vendor related definitions
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Sat, 9 Sep 2023 15:07:09 +0000 (17:07 +0200)]
hostapd: rework reload support and MAC address handling
MAC address and interface name assigned by mac80211.sh depend on the order in
which interfaces are brought up. This order changes when interfaces get added
or removed, which can cause unnecessary reload churn.
One part of the fix it making MAC address allocation more dynamic in both
wpa_supplicant and hostapd, by ignoring the provided MAC address using
the next available one, whenever the config does not explicitly specify one.
The other part is making use of support for renaming netdevs at runtime and
preserving the MAC address for renamed netdevs.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Thu, 7 Sep 2023 20:11:18 +0000 (22:11 +0200)]
mac80211: add multiple BSSID support
This advertises multiple BSS interfaces in a single set of beacons
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Thu, 7 Sep 2023 19:45:11 +0000 (21:45 +0200)]
mac80211: add support for configuring number of globally allocated MAC addresses
When a device has more than one reserved mac address, they can be used for
virtual interfaces without the local bit in the first byte
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Wed, 6 Sep 2023 14:58:09 +0000 (16:58 +0200)]
hostapd: move mac address allocation from mac80211.sh to wdev.uc
Preparation for upcoming hostapd reload improvements
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Wed, 6 Sep 2023 08:33:30 +0000 (10:33 +0200)]
hostapd: add internal API for renaming AP interfaces
Will be used for improving reload support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Wed, 13 Sep 2023 10:36:15 +0000 (12:36 +0200)]
hostapd: fix AP+STA configuration with autochannel enabled
Properly disable the interface when requested
Disable ACS when bringing it back up on the new channel
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Wed, 13 Sep 2023 09:56:20 +0000 (11:56 +0200)]
mac80211: disable automatically created sta interfaces
They are not useful for anything on the system and are annoying when a PHY
is disabled in the config
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Wed, 13 Sep 2023 08:47:34 +0000 (10:47 +0200)]
hostapd: update interface/bss list after set_config calls
set_config causes the ucode bss resource to be re-created and because of that
the bss list needs to be updated as well
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Wed, 13 Sep 2023 05:53:39 +0000 (07:53 +0200)]
mac80211: add missing kernel modules for brcmfmac
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Michał Kwiatek [Thu, 24 Aug 2023 10:18:02 +0000 (12:18 +0200)]
ath11k-firmware: update to stable WLAN.HK.2.9.0.1-01890
Changelog from quic:
Bug fixes, stability improvements from previous releases
are present. There are no backward comatibility issues
with this release.
Known issues:
IPV6 connectivity problem, see: https://github.com/openwrt/openwrt/pull/13203#issuecomment-
1666947749
Tested-by: Michał Kwiatek <michal@kwiatek.it> # Xiaomi AX3600
Signed-off-by: Michał Kwiatek <michal@kwiatek.it>
Brian Norris [Sun, 10 Sep 2023 21:10:50 +0000 (14:10 -0700)]
ipq806x: Correct OnHub sysupgrade config logic
There's a typo in here: board_name is a function, not a variable. This
issue was pointed out on the OpenWrt forum.
Closes: #13409
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Felix Fietkau [Tue, 12 Sep 2023 13:17:23 +0000 (15:17 +0200)]
mac80211: fix mesh id corruption on 32 bit systems
increase size of ifmsh->mbss_changed
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Aviana Cruz [Mon, 20 Jun 2022 13:55:45 +0000 (21:55 +0800)]
ramips: add support for mtk eip93 crypto engine
Mediatek EIP93 Crypto engine is a crypto accelerator which
is available in the Mediatek MT7621 SoC.
Signed-off-by: Aviana Cruz <gwencroft@proton.me>
Co-authored-by: Richard van Schagen <vschagen@icloud.com>
Co-authored-by: Chukun Pan <amadeus@jmu.edu.cn>
Hannu Nyman [Fri, 8 Sep 2023 16:47:01 +0000 (19:47 +0300)]
base-files: sysupgrade: Add 2 sec sleep into process KILL loop
Add 2 seconds sleep after each forcibly killed/tried-to-kill process
in the final process termination loop in sysupgrade stage2.
This is needed especially for qualcommax/ipq807x, where ath11k
wireless driver may have a long 10-20 seconds delay after termination
before actually getting killed. This often breaks sysupgrade.
The current KILL loop in kill_remaining does all 10 kill attempts
consecutively without any delay, as evidenced here in a failing sysupgrade.
It does not allow any time for the process to finalize its internal
termination.
Sat Sep 2 19:05:56 EEST 2023 upgrade: Sending TERM to remaining processes ...
Sat Sep 2 19:05:56 EEST 2023 upgrade: Sending signal TERM to hostapd (2122)
Sat Sep 2 19:05:56 EEST 2023 upgrade: Sending signal TERM to hostapd (2138)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending KILL to remaining processes ...
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending signal KILL to hostapd (2122)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending signal KILL to hostapd (2138)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending signal KILL to hostapd (2138)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending signal KILL to hostapd (2138)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending signal KILL to hostapd (2138)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending signal KILL to hostapd (2138)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending signal KILL to hostapd (2138)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending signal KILL to hostapd (2138)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending signal KILL to hostapd (2138)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending signal KILL to hostapd (2138)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending signal KILL to hostapd (2138)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Failed to kill all processes.
sysupgrade aborted with return code: 256
The change in this commit adds a 2 seconds delay after each kill attempt
in order to allow some processes to more gracefully handle their
internal termination.
The result is like this:
Sun Sep 3 11:15:10 EEST 2023 upgrade: Sending TERM to remaining processes ...
Sun Sep 3 11:15:10 EEST 2023 upgrade: Sending signal TERM to hostapd (2309)
Sun Sep 3 11:15:10 EEST 2023 upgrade: Sending signal TERM to hostapd (2324)
Sun Sep 3 11:15:14 EEST 2023 upgrade: Sending KILL to remaining processes ...
Sun Sep 3 11:15:14 EEST 2023 upgrade: Sending signal KILL to hostapd (2309)
[ 699.827521] br-lan: port 7(hn5wpa2r) entered disabled state
[ 699.908673] device hn5wpa2r left promiscuous mode
[ 699.908721] br-lan: port 7(hn5wpa2r) entered disabled state
[ 701.038029] br-lan: port 6(hn5wpa3) entered disabled state
Sun Sep 3 11:15:16 EEST 2023 upgrade: Sending signal KILL to hostapd (2324)
[ 702.058256] br-lan: port 5(hn2wlan) entered disabled state
[ 709.250063] stage2 (8237): drop_caches: 3
Sun Sep 3 11:15:25 EEST 2023 upgrade: Switching to ramdisk...
The delay introduced here only kicks in if there is some process that
does not get terminated by the first TERM call. Then there is at least
one 2 sec wait after the first KILL loop round.
This commit is related to discussion in PRs #12235 and #12632
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Felix Fietkau [Tue, 12 Sep 2023 12:09:26 +0000 (14:09 +0200)]
hostapd: fix bringing up AP in AP+mesh configurations
Pass the correct frequency + secondary channel offset to hostapd
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Tue, 12 Sep 2023 11:32:40 +0000 (13:32 +0200)]
hostapd: clear ucode interface/bss resource pointers
Avoids potential use-after-free bugs
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Tue, 12 Sep 2023 10:57:52 +0000 (12:57 +0200)]
hostapd: fix applying gratuitous ARP settings with bridge-vlan
The arp_accept setting needs to be applied to the snoop_iface
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Tue, 12 Sep 2023 09:18:35 +0000 (11:18 +0200)]
mac80211: add missing dependency for iwlwifi
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Jonas Gorski [Sat, 9 Sep 2023 10:44:42 +0000 (12:44 +0200)]
x86: geode: fix hwrng register accesses
When the membase and pci_dev pointer were moved to a new struct in priv,
the actual membase users were left untouched, and they started reading
out arbitrary memory behind the struct instead of registers. This
unfortunately turned the RNG into a constant number generator, depending
on the content of what was at that offset.
To fix this, update geode_rng_data_{read,present}() to also get the
membase via amd_geode_priv, and properly read from the right addresses
again.
Closes #13417.
Reported-by: Timur I. Davletshin <timur.davletshin@gmail.com>
Tested-by: Timur I. Davletshin <timur.davletshin@gmail.com>
Suggested-by: Jo-Philipp Wich <jo@mein.io>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Felix Fietkau [Mon, 11 Sep 2023 16:54:04 +0000 (18:54 +0200)]
mac80211: fix build regressions on linux 6.1
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Daniel Golle [Mon, 11 Sep 2023 11:50:38 +0000 (12:50 +0100)]
kernel: backport two fixes for MediaTek Ethernet driver
Fix PSE port assignment for 3rd GMAC on MT7988 and make sure dma_addr
is always initialized to prevent potentially accessing uninitialized
stack memory in the error path.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Felix Fietkau [Wed, 30 Aug 2023 10:31:44 +0000 (12:31 +0200)]
mac80211: update to version 6.5
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Piotr Dymacz [Fri, 28 Jul 2023 10:21:49 +0000 (12:21 +0200)]
uboot-envtools: ramips: add support for ALFA Network AX1800RM
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Piotr Dymacz [Fri, 28 Jul 2023 09:41:14 +0000 (11:41 +0200)]
ramips: add support for ALFA Network AX1800RM
ALFA Network AX1800RM (FCC ID:
2AB877621) is a dual-band Wi-Fi 6
(AX1800) router, based on MediaTek MT7621A + MT79x5D platform.
Specifications:
- SOC: MT7621A (880 MHz)
- DRAM: DDR3 256 MiB (Nanya NT5CC128M16JR-EK)
- Flash: 16 MiB SPI NOR (EN25QH128A-104HIP)
- Ethernet: 4x 10/100/1000 Mbps (SOC's built-in switch)
- Wi-Fi: 2x2:2 2.4/5 GHz (MT7905DAN + MT7975DN)
(MT7905DAN doesn't support background DFS scan/BT)
- LED: 6x green, 1x green/red
- Buttons: 2x (reset, WPS)
- Antenna: 4x external, non-detachable omnidirectional
- UART: 1x 4-pin (2.54 mm pitch, J4, not populated)
- Power: 12 V DC/1 A (DC jack)
MAC addresses:
LAN: 00:c0:ca:xx:xx:4e (factory 0x4, +2)
WAN: 00:c0:ca:xx:xx:4f (factory 0x4, +3)
2.4 GHz: 00:c0:ca:xx:xx:4c (factory 0x4, device's label)
5 GHz: 00:c0:ca:xx:xx:4c (factory 0xa)
Flash instructions for web-based U-Boot recovery:
1. Power the device with WPS button pressed and wait around 10 seconds.
2. Setup static IP 192.168.1.2/24 on your PC.
3. Go to 192.168.1.1 in browser and upload 'recovery' image.
The device runs LEDE 17.01 (kernel 4.4.x) based firmware with 'failsafe'
mode available which allows alternative upgrade method:
1. Run device in 'failsafe' mode and change password for default user.
2. SSH to the device, transfer 'sysupgrade' image and perform upgrade
in forced mode, without preserving settings: 'sysupgrade -n -F ...'.
Other notes:
If you own early version of this device, the vendor firmware might
refuse OpenWrt image because of missing custom header. In that case,
ask vendor's customer support for stock firmware without custom header
support/requirement.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Daniel Golle [Sun, 10 Sep 2023 22:39:33 +0000 (23:39 +0100)]
arm-trusted-firmware-mediatek: fix hang on reboot on MT7622
With recent updates of TF-A the previously already fixed bug slipped
back into the source tree. Again, reorder bl2 init for MT7622 and
initialize WDT only after DRAM init has completed to avoid the
notorious hang.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Fri, 1 Sep 2023 23:54:40 +0000 (00:54 +0100)]
uboot-mediatek: sync mtk-snand driver with SDK
Sync SPI-NAND/ECC controller driver for MT7622, MT7981, MT7986 and MT7988:
* Platform data for MT7981 was actually missing and is now added.
* Add support for Winbond W25N01KV 1Gbit chip.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
David Bauer [Sat, 9 Sep 2023 06:42:04 +0000 (08:42 +0200)]
Revert "ath79: use kernel 6.1 as default"
This reverts commit
c94383de018c561355c5e239524fbefca4aee3aa.
THis commit was not meant to be pushed to main yet.
Signed-off-by: David Bauer <mail@david-bauer.net>
John Audia [Thu, 7 Sep 2023 10:07:43 +0000 (06:07 -0400)]
kernel: bump 6.1 to 6.1.52
Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.1.52
All patches automatically rebased.
Build system: x86/64
Build-tested: x86/64/AMD Cezanne
Run-tested: x86/64/AMD Cezanne
Signed-off-by: John Audia <therealgraysky@proton.me>
Tomasz Maciej Nowak [Thu, 7 Sep 2023 15:06:29 +0000 (17:06 +0200)]
mvebu: cortexa72: enable USB PHY
Since kernel 5.13 this is needed to enable USB ports on all devices in
subtarget. Previously TF-A and COMPHY driver might have set up this PHY,
but not anymore.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Tested-by: Robert Marko <robimarko@gmail.com>
Tomasz Maciej Nowak [Thu, 7 Sep 2023 15:06:28 +0000 (17:06 +0200)]
mvebu: refresh 6.1 configs
This should be a part of kernel major bump. Fortunately it didn't stall
compilation, so no fixes tag.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Patricia Lee [Wed, 30 Aug 2023 11:50:54 +0000 (19:50 +0800)]
mediatek: add support for Cetron CT3003
**Hardware specification:**
- SoC: MediaTek MT7981B 2x A53
- Flash: ESMT F50L1G41LB 128MB
- RAM: Nanya NT5CC128M16JR-EK 256MB
- Ethernet: 4 x 10/100/1000 Mbps
- Switch: MediaTek MT7531AE
- WiFi: MediaTek MT7976C
- Button: Reset, Mesh
- Power: DC 12V 1A
- UART: 3.3v, 115200n8
| Layout: |
| :-------- |
| <Antenna> |
| VCC |
| GND |
| Tx |
| Rx |
**Flash instructions:**
1. Rename `openwrt-mediatek-filogic-cetron_ct3003-squashfs-factory.bin` to `factory.bin`.
2. Upload the `factory.bin` using the device's Web interface.
3. Click the upgrade button and wait for the process to finish.
4. Access the OpenWrt interface using the same password.
5. Use the 'Restore' function to reset the firmware to its initial state.
**Notes:**
If you plan to recovery the stock firmware in the future, it's advisable
to connect the device via the serial port and enter failsafe mode to
back up all the MTD partitions before proceeding the steps above.
Signed-off-by: Patricia Lee <patricialee320@gmail.com>
John Audia [Thu, 7 Sep 2023 10:55:41 +0000 (06:55 -0400)]
kernel: bump 5.15 to 5.15.131
Changelog: https://cdn.kernel.org/pub/linux/kernel/v5.x/ChangeLog-5.15.131
All patches automatically rebased.
Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3
Signed-off-by: John Audia <therealgraysky@proton.me>
David Bauer [Fri, 8 Sep 2023 19:00:23 +0000 (21:00 +0200)]
ath79: use kernel 6.1 as default
Signed-off-by: David Bauer <mail@david-bauer.net>
projects / openwrt / staging / blocktrron.git / log