mmc: mmc_spi: Add Card Detect comments and fix CD GPIO case

This patch fixes the MMC SPI driver from doing polling card detect when a
CD GPIO that supports interrupts is specified using the gpios DT property.

Without this patch the DT node below results in the following output:

 spi_gpio: spi-gpio { /* SD2 @ CN12 */
         compatible = "spi-gpio";
         #address-cells = <1>;
         #size-cells = <0>;
         gpio-sck = <&gpio6 16 GPIO_ACTIVE_HIGH>;
         gpio-mosi = <&gpio6 17 GPIO_ACTIVE_HIGH>;
         gpio-miso = <&gpio6 18 GPIO_ACTIVE_HIGH>;
         num-chipselects = <1>;
         cs-gpios = <&gpio6 21 GPIO_ACTIVE_LOW>;
         status = "okay";

         spi@0 {
                 compatible = "mmc-spi-slot";
                 reg = <0>;
                 voltage-ranges = <3200 3400>;
                 spi-max-frequency = <25000000>;
                 gpios = <&gpio6 22 GPIO_ACTIVE_LOW>;   /* CD */
         };
 };

 # dmesg | grep mmc
 mmc_spi spi32766.0: SD/MMC host mmc0, no WP, no poweroff, cd polling
 mmc0: host does not support reading read-only switch, assuming write-enable
 mmc0: new SDHC card on SPI
 mmcblk0: mmc0:0000 SU04G 3.69 GiB
 mmcblk0: p1

With this patch applied the "cd polling" portion above disappears.

Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Cc: stable@vger.kernel.org # v3.18+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: tegra: Disable UHS-I modes for tegra114

SD card support for Tegra114 started failing after commit a8e326a911d3
("mmc: tegra: implement module external clock change") was merged. This
commit was part of a series to enable UHS-I modes for Tegra. To
workaround this problem for now, disable UHS-I modes for Tegra114 by
separating the soc data structures for Tegra114 and Tegra124 so that
UHS-I is still enabled for Tegra124 but not Tegra114.

Fixes: a8e326a911d3 ("mmc: tegra: implement module external clock change")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sdhci-pltfm: remove priv variable from sdhci_pltfm_host

Now all clients migration to use sdhci_pltfm_init for private
allocation is done and there's no users of the priv variable, so we can
remove it from the sdhci_pltfm_host structure.

Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sdhci-pxav2: remove unnecessary assignment of pltfm_host->priv

The sdhci_pltfm_init() function has initialized the priv member as
NULL, so there's no need to do it again.

Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sdhci-tegra: use sdhci_pltfm_init for private allocation

Commit 0e748234293f ("mmc: sdhci: Add size for caller in init+register")
allows users of sdhci_pltfm to allocate private space in calls to
sdhci_pltfm_init+sdhci_pltfm_register. This patch migrates sdhci-tegra
to this allocation.

Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sdhci-st: use sdhci_pltfm_init for private allocation

Commit 0e748234293f ("mmc: sdhci: Add size for caller in init+register")
allows users of sdhci_pltfm to allocate private space in calls to
sdhci_pltfm_init+sdhci_pltfm_register. This patch migrates sdhci-st
to this allocation.

Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sdhci-pxav3: use sdhci_pltfm_init for private allocation

Commit 0e748234293f ("mmc: sdhci: Add size for caller in init+register")
allows users of sdhci_pltfm to allocate private space in calls to
sdhci_pltfm_init+sdhci_pltfm_register. This patch migrates sdhci-pxav3
to this allocation.

Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sdhci-of-esdhc: use sdhci_pltfm_init for private allocation

Commit 0e748234293f ("mmc: sdhci: Add size for caller in init+register")
allows users of sdhci_pltfm to allocate private space in calls to
sdhci_pltfm_init+sdhci_pltfm_register. This patch migrates the
sdhci-of-esdhc driver to this allocation.

Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sdhci-of-at91: use sdhci_pltfm_init for private allocation

Commit 0e748234293f ("mmc: sdhci: Add size for caller in init+register")
allows users of sdhci_pltfm to allocate private space in calls to
sdhci_pltfm_init+sdhci_pltfm_register. This patch migrates the
sdhci-of-at91 driver to this allocation.

Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sdhci-of-arasan: use sdhci_pltfm_init for private allocation

Commit 0e748234293f ("mmc: sdhci: Add size for caller in init+register")
allows users of sdhci_pltfm to allocate private space in calls to
sdhci_pltfm_init+sdhci_pltfm_register. This patch migrates the
sdhci-of-arasan driver to this allocation.

Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sdhci-of-arasan: fix clk issue in sdhci_arasan_remove()

sdhci_pltfm_unregister() could operate host's registers, it will cause
problems if the clk is already disabled and unprepared. Fix this issue
by moving the clk_disable_unprepare() call to the end of remove
function.

Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sdhci-msm: use sdhci_pltfm_init for private allocation

Commit 0e748234293f ("mmc: sdhci: Add size for caller in init+register")
allows users of sdhci_pltfm to allocate private space in calls to
sdhci_pltfm_init+sdhci_pltfm_register. This patch migrates sdhci-msm
to this allocation.

Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sdhci-msm: factorise sdhci_msm_pdata outisde of sdhci_msm_host

There's no need to allocate one sdhci_msm_pdata for each sdhci_msm_host.
This patch removes the sdhci_msm_pdata member from sdhci_msm_host and
uses one static global sdhci_msm_pdata for all sdhci msm hosts. It also
marks sdhci_msm_ops as const.

Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sdhci-esdhc-imx: use sdhci_pltfm_init for private allocation

Commit 0e748234293f ("mmc: sdhci: Add size for caller in init+register")
allows users of sdhci_pltfm to allocate private space in calls to
sdhci_pltfm_init+sdhci_pltfm_register. This patch migrates the sdhci
esdhc-imx driver to this allocation.

Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sdhci-bcm2835: use sdhci_pltfm_init for private allocation

Commit 0e748234293f ("mmc: sdhci: Add size for caller in init+register")
allows users of sdhci_pltfm to allocate private space in calls to
sdhci_pltfm_init+sdhci_pltfm_register. This patch migrates sdhci-bcm2835
to this allocation.

Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: mediatek: add SD write protect support

use mmc core layer's API to support sd write protect

Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sdhi: Add r8a7795 support

Registers are 64bit apart, so we refactor bus_shift handling a little and set
it based on the DT compatible. Also, EXT_ACC is different. It has been tested
on a Salvator-X (Gen3) and, to check for regressions, on a Lager (Gen2).

Signed-off-by: Ai Kyuse <ai.kyuse.uw@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sdhci: further code simplication

Further simplify the code in sdhci_prepare_data() - we don't set
SDHCI_REQ_USE_DMA anywhere else in the driver, so there is no
need to set it, and then immediately test it.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sdhci: consolidate the DMA/ADMA size/address quicks

Rather than scanning the scatterlist multiple times for each quirk,
scan it once, checking for each possible quirk.  This should be
cheaper due to the length and offset members commonly sharing the
same cache line than scanning the scatterlist multiple times.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sdhci: prepare DMA address/size quirk handling consolidation

Prepare to consolidate the DMA address/size quirk handling into one
single loop.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sdhci: cleanup DMA un-mapping

The patch "mmc: sdhci: plug DMA mapping leak on error" added
un-mapping logic to sdhci_tasklet_finish() where it is always
called, thereby preventing the mapping leaking.

Consequently the un-mapping code in sdhci_finish_data() is no
longer needed.  Remove it.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
[ Split from original "mmc: sdhci: plug DMA mapping leak on error" patch ]
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sdhci: clean up host cookie handling

Commit d31911b9374a ("mmc: sdhci: fix dma memory leak in sdhci_pre_req()")
added a complicated method to manage the DMA map state for the data
transfer, but this complexity is not required.

There are three states:
* Unmapped
* Mapped by sdhci_pre_req()
* Mapped by sdhci_prepare_data()

sdhci_prepare_data() needs to know when the data buffers have been
successfully mapped by sdhci_pre_req(), and if so, there is no need to
map them a second time.

When we come to tear down the mapping, we want to know whether
sdhci_post_req() will be called (which is determined by sdhci_pre_req()
having been previously called) so that we can postpone the unmap
operation.

Hence, it makes sense to simply record when the successful DMA map
happened (via COOKIE_PRE_MAPPED vs COOKIE_MAPPED) rather than having
the complex mechanics involving COOKIE_MAPPED vs COOKIE_GIVEN.

If a mapping is created by sdhci_prepare_data(), we must tear it down
ourselves, without waiting for sdhci_post_req() (hence, the new
COOKIE_MAPPED case).  If the mapping is created by sdhci_pre_req()
then sdhci_post_req() is responsible for tearing the mapping down.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sdhci: always unmap a mapped data transfer in sdhci_post_req()

If the host cookie indicates that the data buffers of a request are
mapped at sdhci_post_req() time, always unmap the data buffers.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sdhci: pass the cookie into sdhci_pre_dma_transfer()

Pass the desired cookie for a successful map.  This is in preparation to
clean up the MAPPED/GIVEN states.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sdhci: factor out sdhci_pre_dma_transfer() from sdhci_adma_table_pre()

In sdhci_prepare_data(), when SDHCI_REQ_USE_DMA is set, there are two
paths that prepare the data buffers for transfer.  One is when
SDHCI_USE_ADMA is set, and is located inside sdhci_adma_table_pre().
The other is when SDHCI_USE_ADMA is clear, in the else clause of the
above.

Factor out the call to sdhci_pre_dma_transfer() along with its error
checking.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sdhci: move sdhci_pre_dma_transfer()

Move sdhci_pre_dma_transfer() to avoid needing to declare this function
before use.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sdhci: factor out common DMA cleanup in sdhci_finish_data()

sdhci_finish_data() has two paths which result in identical DMA cleanup.
One is when SDHCI_USE_ADMA is clear, and the other is just before when
SDHCI_USE_ADMA is set, and is performed within sdhci_adma_table_post().

Simplify the code by removing the 'else' and eliminating the duplicate
inside sdhci_adma_table_post().

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sdhci: avoid walking SG list for writes

If we are writing data to the card, there is no point in walking the
scatterlist to find out if there are any unaligned entries; this is a
needless waste of CPU cycles.  Avoid this by checking for a non-read
tranfer first.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sdhci: clean up coding style in sdhci_adma_table_pre()

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sdhci: allocate alignment and DMA descriptor buffer together

Allocate both the alignment and DMA descriptor buffers together.  The
size of the alignment buffer will always be aligned to the hosts
required alignment, which gives appropriate alignment to the DMA
descriptors.

We have a maximum of 128 segments, and a maximum alignment of 64 bits.
This gives a maximum alignment buffer size of 1024 bytes.

The DMA descriptors are a maximum of 12 bytes, and we allocate 128 * 2
+ 1 of these, which gives a maximum DMA descriptor buffer size of 3084
bytes.

This means the allocation for a 4K page sized system will be an order-1
allocation, since the resulting overall size is 4108.  This is more
prone to failure than page-sized allocations, but since this allocation
commonly occurs at startup, the chances of failure are small.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
[ Changed to check ADMA table alignment ]
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sdhci: fix data timeout (part 2)

The calculation for the timeout based on the number of card clocks is
incorrect.  The calculation assumed:

timeout in microseconds = clock cycles / clock in Hz

which is clearly a several orders of magnitude wrong.  Fix this by
multiplying the clock cycles by 1000000 prior to dividing by the Hz
based clock.  Also, as per part 1, ensure that the division rounds
up.

As this needs 64-bit math via do_div(), avoid it if the clock cycles
is zero.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v3.15+
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sdhci: fix data timeout (part 1)

The data timeout gives the minimum amount of time that should be
waited before timing out if no data is received from the card.
Simply dividing the nanosecond part by 1000 does not give this
required guarantee, since such a division rounds down.  Use
DIV_ROUND_UP() to give the desired timeout.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v3.15+
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sdhci: further fix for DMA unmapping in sdhci_post_req()

sdhci_post_req() exists to unmap a previously mapped but already
finished request, while the next request is in progress.  However, the
state of the SDHCI_REQ_USE_DMA flag depends on the last submitted
request.

This means we can end up clearing the flag due to a quirk, which then
means that sdhci_post_req() fails to unmap the DMA buffer, potentially
leading to data corruption.

We can safely ignore the SDHCI_REQ_USE_DMA here, as testing
data->host_cookie is entirely sufficient.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
[ Re-based to apply as a separate fix ]
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.5+
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sdhci-pxav3: fix higher speed mode capabilities

Commit 1140011ee9d9 ("mmc: sdhci-pxav3: Modify clock settings for the
SDR50 and DDR50 modes") broke any chance of the SDR50 or DDR50 modes
being used.

The commit claims that SDR50 and DDR50 require clock adjustments in
the SDIO3 Configuration register, which is located via the "conf-sdio3"
resource.  However, when this resource is given, we fail to read the
host capabilities 1 register, resulting in host->caps1 being zero.
Hence, both SDHCI_SUPPORT_SDR50 and SDHCI_SUPPORT_DDR50 bits remain
zero, disabling the SDR50 and DDR50 modes.

The underlying idea in this function appears to be to read the device
capabilities, modify them, and set SDHCI_QUIRK_MISSING_CAPS to cause
our modified capabilities to be used.  Implement exactly that.

Fixes: 1140011ee9d9 ("mmc: sdhci-pxav3: Modify clock settings for the SDR50 and DDR50 modes")
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: stable@vger.kernel.org # v4.5+
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sdhci: plug DMA mapping leak on error

If we terminate a command early, we fail to properly clean up the DMA
mappings for the data part of the request.  Put this clean up to the
tasklet, which is the common path for finishing a request so we always
clean up after ourselves.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
[ Split original patch so that it now contains only the fix ]
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.5+
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sdhci: avoid unnecessary mapping/unmapping of align buffer

Unnecessarily mapping and unmapping the align buffer for SD cards is
expensive: performance measurements on iMX6 show that this gives a hit
of 10% on hdparm buffered disk reads.

MMC/SD card IO comes from the mm/vfs which gives us page based IO, so
for this case, the align buffer is not going to be used.  However, we
still map and unmap this buffer.

Eliminate this by switching the align buffer to be a DMA coherent
buffer, which needs no DMA maintenance to access the buffer.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.5+
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sdhci: fix command response CRC error handling

When we get a response CRC error on a command, it means that the
response we received back from the card was not correct.  It does not
mean that the card did not receive the command correctly.  If the
command is one which initiates a data transfer, the card can enter the
data transfer state, and start sending data.

Moreover, if the request contained a data phase, we do not clean this
up, and this results in the driver triggering DMA API debug warnings,
and also creates a race condition in the driver, between running the
finish_tasklet and the data transfer interrupts, which can trigger a
"Got data interrupt" state dump.

Fix this by handing a response CRC error slightly differently: record
the failure of the data initiating command, but allow the remainder of
the request to be processed normally.  This is safe as core MMC checks
the status of all commands and data transfer phases of the request.

If the card does not initiate a data transfer, then we should time out
according to the data transfer parameters.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
[ Fix missing parenthesis around bitwise-AND expression, and tweak subject ]
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.5+
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sdhci: clean up command error handling

Avoid multiple tests while handling a command error; simplify the code.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
[ Goes with "mmc: sdhci: fix command response CRC error handling" ]
Cc: stable@vger.kernel.org # v4.5+
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sdhci: move initialisation of command error member

When a command is started, logically it has no error.  Initialise the
command's error member to zero whenever we start a command.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
[ Goes with "mmc: sdhci: fix command response CRC error handling" ]
Cc: stable@vger.kernel.org # v4.5+
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

MAINTAINERS: mmc: Add Adrian Hunter as the maintainer for SDHCI

up the maintainer role for SDHCI. I am very pleased that Adrian Hunter
volunteered and accepted the challenge!

The SDHCI code is currently in quite poor quality, but we have agreed on
a way forward to try to reach a point where the SDHCI core becomes more of
a set of library functions. Each SDHCI driver variant can then decide
which functions to use and allows it to implement variant specific code,
without needing to also change SDHCI core code.

In the end we aim to get better optimized and maintainable code.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>

mmc: sdhci: Allow CAPS check for SDHCI_CAN_64BIT to use overridden caps

sdhci_add_host() allows the Host Controller Capability registers
to be supplied by the calling driver by using
SDHCI_QUIRK_MISSING_CAPS, but the check for the Capabilities bit
SDHCI_CAN_64BIT doesn't use the applied value and instead reads
the Host register directly. This change uses the supplied "caps"
register instead of reading the host register.

This change will allow a calling driver to simply clear the
SDHCI_CAN_64BIT bit in "caps" to handle some cases of
SDHCI_QUIRK2_BROKEN_64_BIT_DMA.

Signed-off-by: Al Cooper <alcooperx@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sdhci-pic32: Add PIC32 SDHCI host controller driver

This driver supports the SDHCI host controller found on a PIC32.

Signed-off-by: Andrei Pistirica <andrei.pistirica@microchip.com>
Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>

dt/bindings: mmc: Add bindings for PIC32 SDHCI host controller

Document the devicetree bindings for the SDHCI peripheral found on
Microchip PIC32 class devices.

Signed-off-by: Andrei Pistirica <andrei.pistirica@microchip.com>
Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>

mmc: dw_mmc: fix num_slots setting

This patch make num_slots to 1 if pdata->num_slot is not
defined. Meanwhile, we need to make sure num_slots should
not larger that the supported slots

Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: dw_mmc: remove repetitive clear interrupt

dw_mci_probe clear interrupts and disable all interrupts firstly.
While it clear interrupt again before enable some interrupts. We
can't see any reason to clear it twice here, so remove the second one.

Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: dw_mmc: fix err handle of dw_mci_probe

This patch add correct err handle if dw_mci_ctrl_reset
failed while probing.

Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: dw_mmc: remove DW_MCI_QUIRK_BROKEN_CARD_DETECTION quirk

dw_mmc already use mmc_of_parse to get "broken-cd" property,
but it considered "broken-cd" to be a quirk in its driver. We
don't need this quirk here, and just take what we need from
mmc->caps.

Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: dw_mmc: remove struct block_settings

This patch removes struct block_settings since
it's never used anywhere.

Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: dw_mmc: add hw_reset support

This patch implement hw_reset function for DesignWare
MMC controller. By adding this feature, mmc blk can
do some basic recovery.

Set the following resets:
software reset – BMOD[0] for IDMAC only
DMA reset - CTRL[2]
FIFO reset - CTRL[1] bits

Program the CARD_RESET register with a value of 0 for the bit
corresponding to the card number; This programming asserts the
RST_n signal and resets the card. After a minimum of 1 ?s, de-asserts the
RST_n signal and takes the card out of reset. The application can program
a new CMD only after a minimum of 200 us

This implementation can be easily tested by cutting off->On vmmc
while doing data accessing in background to simulate that case.

Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: dw_mmc: remove the prepare_command hook

This patch removes the prepare_command hook from entire dw_mmc driver.
Now, almost all SoCs are using by default, except Exynos.
It seems that dwmmc controller is using unnecessary hook.
To know whether needs to set this bit or not,
add the DW_MMC_CARD_NO_USE_HOLD bit.

If some SoCs need to disable this in future, just set the
DW_MMC_CARD_NO_USE_HOLD bit.
set_bit(DW_MMC_CARD_NO_USE_HOLD, &slot->flags),

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: core: report tuning command execution failure reason

Print the error code when the tuning command fails.  This allows the
reason for the failure to be reported, which aids debugging.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: block: shut up "retrying because a re-tune was needed" message

Re-tuning is part of standard requirements for the higher speed SD
card protocols, and is not an error when this occurs.  When we retry
a command due to a retune, we should not print a message to the
kernel log.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: core: improve mmc_of_parse_voltage() to return better status

Improve mmc_of_parse_voltage()'s return values so that drivers can tell
whether a voltage-range specification was present, and whether it has
been successfully parsed, or there was an error while parsing.

We return a negative errno when parsing fails, zero if no voltage-range
specification is present, or one if a voltage-range specification is
successfully parsed.

No users need modifying as no users check the return value.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: core: shut up "voltage-ranges unspecified" pr_info()

Each time a driver such as sdhci-esdhc-imx is probed, we get a info
printk complaining that the DT voltage-ranges property has not been
specified.

However, the DT binding specifically says that the voltage-ranges
property is optional.  That means we should not be complaining that
DT hasn't specified this property: by indicating that it's optional,
it is valid not to have the property in DT.

Silence the warning if the property is missing.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: tmio: disable clock before changing it

Rcar2 & 3 docs state that for going to and coming from the 0xff setting,
the clock must first be disabled before the DIV bits are changed.
Instead of tracking this, let's just do this unconditionally.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: tmio: refactor set_clock a little

Some of the indentation made the code awful to read. Fix that. Also,
introduce defines instead of magic hex values. Note that this includes
one change: We mask out know 0xff instead of 0x1ff. But 0x100 has always
been the clock enable bit. It doesn't make any sense to set it depending
on the clock calculation. Update copyright notices, too. I'll be working
on those files some more in the future.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sdhi: use faster clock handling on RCar Gen2

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: tmio: remove stale comments

These don't make sense anymore. Since commit 5d60e500541ed1 ("mmc: tmio:
add new TMIO_MMC_HAVE_HIGH_REG flags"), we don't deal with a resource
here.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: tmio: add flag to reduce delay after changing clock status

The docs for RCar Gen2 & 3 I have access to, mention delays of 5ms after
stop and 1ms after start. Make it possible to apply these values.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sdhi: error message on ENOMEM is superfluous

We will get a full dump anyhow.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sdhi: Add EXT_ACC register busy check

All the docs I have access to say that this register needs the bus busy
check.

Signed-off-by: Shinobu Uehara <shinobu.uehara.xc@renesas.com>
Signed-off-by: Ai Kyuse <ai.kyuse.uw@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: tmio_dma: remove debug messages with little information

When compiling the driver with CONFIG_MMC_DEBUG set, I got build
warnings. They have been 'fixed' meanwhile. However, because these debug
messages look random anyhow (some duplicate information printed etc),
let's just drop them and rather re-add something consistent if that
should ever be needed.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: block: don't use the OR operation for flag of data

After removed the MMC_DATA_STREAM, only two flags are remained.
(MMC_DATA_READ and MMC_DATA_WRITE)
The flags of  READ and WRITE can't be used together.
That's why it doesn't need to use "OR' operation.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: core: remove the MMC_DATA_STREAM flag

It's not set to MMC_DATA_STREAM anywhere.
It seems that it had been used with CMD11/CMD20.
But according to Spec, CMD11/CMD20 are obsolete command.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sunxi-mmc: remove the MMC_DATA_STREAM flag

Remove the MMC_DATA_STREAM flag because it isn't used anymore.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: s3cmci: remove the MMC_DATA_STREAM flag

Remove the MMC_DATA_STREAM flag because it isn't used anymore.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: pxamci: remove the MMC_DATA_STREAM flag

Remove the MMC_DATA_STREAM flag because it isn't used anymore.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: mxcmmc: remove the MMC_DATA_STREAM flag

Remove the MMC_DATA_STREAM flag because it isn't used anymore.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: jz4740_mmc: remove the MMC_DATA_STREAM flag

Remove the MMC_DATA_STREAM flag because it isn't used anymore.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: dw_mmc: remove the MMC_DATA_STREAM flag

Remove the MMC_DATA_STREAM flag because it isn't used anymore.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: davinci_mmc: remove the MMC_DATA_STREAM flag

Remove the MMC_DATA_STREAM flag because it isn't used anymore.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: bfin_sdh: remove the MMC_DATA_STREAM flag

Remove the MMC_DATA_STREAM flag because it isn't used anymore.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: atmel-mci: remove the MMC_DATA_STREAM flag

Remove the MMC_DATA_STREAM flag because it isn't used anymore.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sunxi: Enable eMMC HS-DDR (MMC_CAP_1_8V_DDR) support

Now that clock delay settings for 8 bit DDR are correct, and vqmmc
support is available, we can enable MMC_CAP_1_8V_DDR support. This
enables MMC HS-DDR at up to 52 MHz, even if signal voltage switching
is not available.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sunxi: Support 8 bit eMMC DDR transfer modes

Allwinner's MMC controller needs to run at double the card clock rate
for 8 bit DDR transfer modes. Interestingly, this is not needed for
4 bit DDR transfers.

Different clock delays are needed for 8 bit eMMC DDR, due to the
increased module clock rate. For the A80 though, the same values for
4 bit and 8 bit are shared. The new values for the other SoCs were from
A83T user manual's "new timing mode" default values, which describes
them in clock phase, rather than delay periods. These values were used
without any modification. They may not be correct, but they work.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sunxi: Support MMC_DDR52 timing modes

DDR transfer modes include UHS-1 DDR50 and MMC HS-DDR (or MMC_DDR52).
Consider MMC_DDR52 when setting clock delays.

Since MMC high speed mode goes up to 52 MHz instead of 50 MHz for SD,
and this number is visible in the capability macro, increase the
clock rate upper limit to 52 MHz.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sanitize 'bus width' in debug output

The bus width is sometimes the actual bus width, and sometimes indices
to different arrays encoding the bus width. In my debugging case "2"
could mean 8-bit as well as 4-bit, which was extremly confusing. Let's
use the human-readable actual bus width in all places.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: core: use the defined function to check whether card is removable

In linux/mmc/host.h, mmc_card_is_removable() is already defined.
There is no reason that it doesn't use.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sdhci-iproc: use sdhci_pltfm_unregister directly

The sdhci_iproc_remove() is jsut a wrapper to sdhci_pltfm_unregister.
So use the sdhci_pltfm_unregister() for the .remove hook directly.

Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: DT: sdhci-iproc: add bcm2835 compatible

Since sdhci-iproc can support bcm2835 we need add the
compatible string to the binding.

Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Scott Branden <sbranden@broadcom.com>
Acked-by: Eric Anholt <eric@anholt.net>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Scott Branden <sbranden@broadcom.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sdhci-iproc: add bcm2835 support

Scott Branden from Broadcom said that the BCM2835 eMMC IP core is
very similar to IPROC and share most of the quirks. So use this driver
instead of separate one.

The sdhci-iproc contains a better workaround for the clock domain
crossing problem which doesn't need any delays. This results in a
better write performance.

Btw we get the rid of the SDHCI_CAPABILITIES hack in the sdhci_readl
function.

Suggested-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Eric Anholt <eric@anholt.net>
Acked-by: Scott Branden <sbranden@broadcom.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sdhci-iproc: define MMC caps in platform data

This patch moves the definition of the MMC capabilities
from the probe function into iproc platform data. After
that we are able to add support for another platform more
easily.

Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Suggested-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Scott Branden <sbranden@broadcom.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: mmc_test: mention that '0' runs all tests

I had to use the source to determine what I need to write to 'test' so
that all tests are run. Let's mention this explicitly in 'testlist'.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: mmcif: don't depend on MMC_BLOCK

I don't see a reason why a host driver should depend on the card driver.
It also prevents that we can use the mmc_test driver. So, remove it.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: make MAN_BKOPS_EN message a debug

IMO this info is only useful for developers. Most users won't need this
information, since there is not much they can do about it.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: omap_hsmmc: don't print uninitialized variables

When DT based probing is used but the DMA request fails, the
driver will print uninitialized stack data from the rx_req
and tx_req variables, as indicated by this warning:

drivers/mmc/host/omap_hsmmc.c: In function 'omap_hsmmc_probe':
drivers/mmc/host/omap_hsmmc.c:2162:3: warning: 'rx_req' may be used uninitialized in this function [-Wmaybe-uninitialized]
   dev_err(mmc_dev(host->mmc), "unable to obtain RX DMA engine channel %u\n", rx_req);

This removes the DMA request line number from the warning, which
is the easiest solution and won't hurt us any more as we are
planning to remove the legacy code path anyway.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sdhci-acpi: enable sdhci-acpi device to suspend/resume asynchronously

This patch enables sdhci-acpi devices to suspend/resume asynchronously.
This will improve system suspend/resume speed. After enabling the
sdhci-acpi devices and all their child devices to suspend/resume
asynchronously on ASUS T100TA, the system suspend-to-idle time is
reduced from 1645ms to 1089ms, and the system resume time is reduced
from 940ms to 908ms.

Signed-off-by: Zhonghui Fu <zhonghui.fu@linux.intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: core: enable mmc host device to suspend/resume asynchronously

This patch enables mmc hosts to suspend/resume asynchronously.
This will improve system suspend/resume speed. After applying
this patch and enabling all mmc hosts' child devices to
suspend/resume asynchronously on ASUS T100TA, the system
suspend-to-idle time is reduced from 1645ms to 1107ms, and the
system resume time is reduced from 940ms to 914ms.

Signed-off-by: Zhonghui Fu <zhonghui.fu@linux.intel.com>
Acked-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sunxi: Support vqmmc regulator

eMMC chips require 2 power supplies, vmmc for internal logic, and vqmmc
for driving output buffers. vqmmc also controls signaling voltage. Most
boards we've seen use the same regulator for both, nevertheless the 2
have different usages, and should be set separately.

This patch adds support for vqmmc regulator supply, including voltage
switching. The MMC core can use this to try different signaling voltages
for eMMC.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sunxi: Return error on mmc_regulator_set_ocr() fail in .set_ios op

Let .set_ios() fail if mmc_regulator_set_ocr() fails to enable and set a
proper voltage for vmmc.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sunxi: Document host init sequence

sunxi_mmc_init_host() originated from Allwinner kernel sources. The
magic numbers written to various registers was never documented.

Add comments for values found in Allwinner user manuals.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sdhci-iproc: Actually enable the clock

The RPi firmware-based clocks driver can actually disable
unused clocks, so when switching to use it we ended up losing
our MMC clock once all devices were probed.

This patch adopts the changes from 1e5a0a9a58e2 ("mmc: sdhci-bcm2835:
Actually enable the clock") to sdhci-iproc.

Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: debugfs: Add a restriction to mmc debugfs clock setting

Clock frequency values written to an mmc host should not be less than
the minimum clock frequency which the mmc host supports.

Signed-off-by: Yuan Juntao <juntaox.yuan@intel.com>
Signed-off-by: Pawel Wodkowski <pawelx.wodkowski@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sdhci-iproc: Clean up platform allocations if shdci init fails

This patch adopts the changes from 475c9e43bfa7 ("mmc: sdhci-bcm2835:
Clean up platform allocations if sdhci init fails") to sdhci-iproc.

Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sdhci-of-arasan: Remove no-hispd and no-cmd23 quirks for sdhci-arasan4.9a

The Arason SD host controller supports set block count command (cmd23)
and high speed mode. This patch re-enable both of these features that
was disabled. For device that doesn't support high speed, it should
configure its capability register accordingly instead disables it
explicitly.

Signed-off-by: Rameshwar Prasad Sahu <rsahu@apm.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: host: omap_hsmmc: add a verbose print to enable CONFIG_REGULATOR_PBIAS

Since v4.3+, CONFIG_REGULATOR_PBIAS should be enabled (for platforms that
have PBIAS regulator) in order for MMC1 to work.

Add a more verbose print to help enable CONFIG_REGULATOR_PBIAS for users
using a olddefconfig or a custom .config.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: remove unnecessary assignment statements before return

Variable assignment just before return is redundant.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: core: pwrseq_simple: remove unused header file

Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: usdhi6rol0: use to_delayed_work

Use to_delayed_work() instead of open-coding it.

Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sh_mmcif: use to_delayed_work

Use to_delayed_work() instead of open-coding it.

Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>