git.openwrt.org Git - openwrt/staging/blogic.git/log

net: stmmac: tc: Remove the speed dependency

XGMAC3 supports full CBS features with speeds that can go up to 10G so
we can now remove the maximum speed check of CBS.

Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: stmmac: xgmac: Add C45 PHY support in the MDIO callbacks

Add the support for C45 PHYs in the MDIO callbacks for XGMAC. This was
tested using Synopsys DesignWare XPCS.

v2:
- Pull out the readl_poll_timeout() calls into common code (Andrew)

Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: stmmac: gmac4+: Add Split Header support

GMAC4+ cores also support the Split Header feature.

Add the support for Split Header feature in the RX path following the
same implementation logic that XGMAC followed.

Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: stmmac: Fix sparse warning

The VID is converted to le16 so the variable must be __le16 type.

Reported-by: kbuild test robot <lkp@intel.com>
Fixes: c7ab0b8088d7 ("net: stmmac: Fallback to VLAN Perfect filtering if HASH is not available")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

cxgb4: remove redundant assignment to hdr_len

Variable hdr_len is being assigned a value that is never read.
The assignment is redundant and hence can be removed.

Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: fix update of the uninitialized variable err

Variable err is not uninitialized and hence can potentially contain
any garbage value. This may cause an error when logical or'ing the
return values from the calls to functions crypto_aead_setauthsize or
crypto_aead_setkey. Fix this by setting err to the return of
crypto_aead_setauthsize rather than or'ing in the return into the
uninitialized variable

Addresses-Coverity: ("Uninitialized scalar variable")
Fixes: fc1b6d6de220 ("tipc: introduce TIPC encryption & authentication")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Documentation: networking: dpaa_eth: adjust sysfs paths

The sysfs paths changed, updating to the current ones.

Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Documentation: networking: dpaa_eth: adjust buffer pool info

Recent changes in the dpaa_eth driver reduced the number of
buffer pools per interface from three to one.

Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

samples/bpf: adjust Makefile and README.rst

Side effect of some kbuild changes resulted in breaking the
documented way to build samples/bpf/.

This patch change the samples/bpf/Makefile to work again, when
invoking make from the subdir samples/bpf/. Also update the
documentation in README.rst, to reflect the new way to build.

Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlxsw: core: Enable devlink reload only on probe

Call devlink enable only during probe time and avoid deadlock
during reload.

Reported-by: Shalom Toledo <shalomt@mellanox.com>
Fixes: a0c76345e3d3 ("devlink: disallow reload operation during device cleanup")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Tested-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

r8169: add support for RTL8117

Add support for chip version RTL8117. Settings have been copied from
Realtek's r8168 driver, there however chip ID 54a belongs to a chip
version called RTL8168FP. It was confirmed that RTL8117 works with
Realtek's driver, so both chip versions seem to be the same or at
least compatible.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'sfp-Allow-slow-to-initialise-GPON-modules-to-work'

Russell King says:

====================
sfp: Allow slow to initialise GPON modules to work

Some GPON modules take longer than the SFF MSA specified time to
initialise and respond to transactions on the I2C bus for either
both 0x50 and 0x51, or 0x51 bus addresses.  Technically these modules
are non-compliant with the SFP Multi-Source Agreement, they have
been around for some time, so are difficult to just ignore.

Most of the patch series is restructuring the code to make it more
readable, and split various things into separate functions.

We split the three state machines into three separate functions, and
re-arrange them to start probing the module as soon as a module has
been detected (without waiting for the network device.)  We try to
read the module's EEPROM, retrying quickly for the first second, and
then once every five seconds for about a minute until we have read
the EEPROM.  So that the kernel isn't entirely silent, we print a
message indicating that we're waiting for the module to respond after
the first second, or when all retries have expired.

Once the module ID has been read, we kick off a delayed work queue
which attempts to register the hwmon, retrying for up to a minute if
the monitoring parameters are unreadable; this allows us to proceed
with module initialisation independently of the hwmon state.

With high-power modules, we wait for the netdev to be attached before
switching the module power mode, and retry this in a similar way to
before until we have successfully read and written the EEPROM at 0x51.

We also move the handling of the TX_DISABLE signal entirely to the main
state machine, and avoid probing any on-board PHY while TX_FAULT is
set.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

net: sfp: allow modules with slow diagnostics to probe

When a module is inserted, we attempt to read read the ID from address
0x50.  Once we are able to read the ID, we immediately attempt to
initialise the hwmon support by reading from address 0x51.  If this
fails, then we fall into error state, and assume that the module is
not usable.

Modules such as the ALCATELLUCENT 3FE46541AA use a real EEPROM for
I2C address 0x50, which responds immediately.  However, address 0x51
is an emulated, which only becomes available once the on-board firmware
has booted.  This prompts us to fall into the error state.

Since the module may be usable without diagnostics, arrange for the
hwmon probe independent of the rest of the SFP itself, retrying every
5s for up to about 60s for the monitoring to become available, and
print an error message if it doesn't become available.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: sfp: allow sfp to probe slow to initialise GPON modules

Some GPON modules (e.g. Huawei MA5671A) take a significant amount of
time to start responding on the I2C bus, contary to the SFF
specifications.

Work around this by implementing a two-level timeout strategy, where
we initially quickly retry for the module, and then use a slower retry
after we exceed a maximum number of quick attempts.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: sfp: move module insert reporting out of probe

Move the module insertion reporting out of the probe handling, but
after we have detected that the upstream has attached (since that is
whom we are reporting insertion to.)

Only report module removal if we had previously reported a module
insertion.

This gives cleaner semantics, and means we can probe the module before
we have an upstream attached.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: sfp: split power mode switching from probe

Switch the power mode switching from the probe, so that we don't
repeatedly re-probe the SFP device if there is a problem accessing
the registers at I2C address 0x51.

In splitting this out, we can also fix a bug where we leave the module
in high-power mode when the upstream device is detached but the module
is still inserted.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: sfp: track upstream's attachment state in state machine

Track the upstream's attachment state in the state machine rather than
maintaining a boolean, which ensures that we have a strict order of
ATTACH followed by an UP event - we can never believe that a newly
attached upstream will be anything but down.

Rearrange the order of state machines so we run the module state
machine after the upstream device's state machine, so the module state
machine can check the current state of the device and take action to
e.g. reset back to empty state when the upstream is detached.

This is to allow the module detection to run independently of the
network device becoming available.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: sfp: ensure TX_FAULT has deasserted before probing the PHY

TX_FAULT should be deasserted to indicate that the module has completed
its initialisation. This may include the on-board PHY, so wait until
the module has deasserted TX_FAULT before probing the PHY.

This means that we need an extra state to handle a TX_FAULT that
remains set for longer than t_init, since using the existing handling
state would bypass the PHY probe.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: sfp: allow fault processing to transition to other states

Add the next state to sfp_sm_fault() so that it can branch to other
states. This will be necessary to improve the initialisation path.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: sfp: eliminate mdelay() from PHY probe

Rather than using mdelay() to wait before probing the PHY (which holds
several locks, including the rtnl lock), add an extra wait state to
the state machine to introduce the 50ms delay without holding any
locks.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: sfp: split the PHY probe from sfp_sm_mod_init()

Move the PHY probe into a separate function, splitting it from
sfp_sm_mod_init(). This will allow us to eliminate the 50ms mdelay()
inside the state machine.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: sfp: control TX_DISABLE and phy only from main state machine

We initialise TX_DISABLE when the sfp cage is probed, and then
maintain its state in the main state machine.  However, the module
state machine:
- negates it when detecting a newly inserted module when it's already
  guaranteed to be negated.
- negates it when the module is removed, but the main state machine
  will do this anyway.

Make TX_DISABLE entirely controlled by the main state machine.

The main state machine also probes the module for a PHY, and removes
the PHY when the the module is removed.  Hence, removing the PHY in
sfp_sm_module_remove() is also redundant, and is a left-over from
when we tried to probe for the PHY from the module state machine.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: sfp: avoid power switch on address-change modules

If the module indicates that it requires an address change sequence to
switch between address 0x50 and 0x51, which we don't support, we can't
write to the register that controls the power mode to switch to high
power mode. Warn the user that the module may not be functional in
this case, and don't try to change the power mode.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: sfp: parse SFP power requirement earlier

Parse the SFP power requirement earlier, in preparation for moving the
power level setup code.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: sfp: rename T_PROBE_WAIT to T_SERIAL

SFF-8472 rev 12.2 defines the time for the serial bus to become ready
using t_serial. Use this as our identifier for this timeout to make
it clear what we are referring to.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: sfp: handle module remove outside state machine

Removing a module resets the module state machine back to its initial
state. Rather than explicitly handling this in every state, handle it
early on outside of the state machine.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: sfp: rename sfp_sm_ins_next() as sfp_sm_mod_next()

sfp_sm_ins_next() modifies the module state machine. Change it's name
to reflect this.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: sfp: move tx disable on device down to main state machine

Move the tx disable assertion on device down to the main state
machine.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: sfp: move sfp sub-state machines into separate functions

Move the SFP sub-state machines out of the main state machine function,
in preparation for it doing a bit more with the device state. By doing
so, we ensure that our debug after the main state machine is always
printed.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: sfp: fix sfp_bus_put() kernel documentation

The kbuild test robot found a problem with htmldocs with the recent
change to the SFP interfaces. Fix the kernel documentation for
sfp_bus_put() which was missing an '@' before the argument name
description.

Fixes: 727b3668b730 ("net: sfp: rework upstream interface")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

r8169: respect EEE user setting when restarting network

Currently, if network is re-started, we advertise all supported EEE
modes, thus potentially overriding a manual adjustment the user made
e.g. via ethtool. Be friendly to the user and preserve a manual
setting on network re-start.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

lwtunnel: ignore any TUNNEL_OPTIONS_PRESENT flags set by users

TUNNEL_OPTIONS_PRESENT (TUNNEL_GENEVE_OPT|TUNNEL_VXLAN_OPT|
TUNNEL_ERSPAN_OPT) flags should be set only according to
tb[LWTUNNEL_IP_OPTS], which is done in ip_tun_parse_opts().

When setting info key.tun_flags, the TUNNEL_OPTIONS_PRESENT
bits in tb[LWTUNNEL_IP(6)_FLAGS] passed from users should
be ignored.

While at it, replace all (TUNNEL_GENEVE_OPT|TUNNEL_VXLAN_OPT|
TUNNEL_ERSPAN_OPT) with 'TUNNEL_OPTIONS_PRESENT'.

Fixes: 3093fbe7ff4b ("route: Per route IP tunnel metadata via lightweight tunnel")
Fixes: 32a2b002ce61 ("ipv6: route: per route IP tunnel metadata via lightweight tunnel")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

lwtunnel: get nlsize for erspan options properly

erspan v1 has OPT_ERSPAN_INDEX while erspan v2 has OPT_ERSPAN_DIR and
OPT_ERSPAN_HWID attributes, and they require different nlsize when
dumping.

So this patch is to get nlsize for erspan options properly according
to erspan version.

Fixes: b0a21810bd5e ("lwtunnel: add options setting and dumping for erspan")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

lwtunnel: change to use nla_parse_nested on new options

As the new options added in kernel, all should always use strict
parsing from the beginning with nla_parse_nested(), instead of
nla_parse_nested_deprecated().

Fixes: b0a21810bd5e ("lwtunnel: add options setting and dumping for erspan")
Fixes: edf31cbb1502 ("lwtunnel: add options setting and dumping for vxlan")
Fixes: 4ece47787077 ("lwtunnel: add options setting and dumping for geneve")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'Accomodate-DSA-front-end-into-Ocelot'

Vladimir Oltean says:

====================
Accomodate DSA front-end into Ocelot

After the nice "change-my-mind" discussion about Ocelot, Felix and
LS1028A (which can be read here: https://lkml.org/lkml/2019/6/21/630),
we have decided to take the route of reworking the Ocelot implementation
in a way that is DSA-compatible.

This is a large series, but hopefully is easy enough to digest, since it
contains mostly code refactoring. What needs to be changed:
- The struct net_device, phy_device needs to be isolated from Ocelot
  private structures (struct ocelot, struct ocelot_port). These will
  live as 1-to-1 equivalents to struct dsa_switch and struct dsa_port.
- The function prototypes need to be compatible with DSA (of course,
  struct dsa_switch will become struct ocelot).
- The CPU port needs to be assigned via a higher-level API, not
  hardcoded in the driver.

What is going to be interesting is that the new DSA front-end of Ocelot
will need to have features in lockstep with the DSA core itself. At the
moment, some more advanced tc offloading features of Ocelot (tc-flower,
etc) are not available in the DSA front-end due to lack of API in the
DSA core. It also means that Ocelot practically re-implements large
parts of DSA (although it is not a DSA switch per se) - see the FDB API
for example.

The code has been only compile-tested on Ocelot, since I don't have
access to any VSC7514 hardware. It was proven to work on NXP LS1028A,
which instantiates a DSA derivative of Ocelot. So I would like to ask
Alex Belloni if you could confirm this series causes no regression on
the Ocelot MIPS SoC.

The goal is to get this rework upstream as quickly as possible,
precisely because it is a large volume of code that risks gaining merge
conflicts if we keep it for too long.

This is but the first chunk of the LS1028A Felix DSA driver upstreaming.
For those who are interested, the concept can be seen on my private
Github repo, the user of this reworked Ocelot driver living under
drivers/net/dsa/vitesse/:
https://github.com/vladimiroltean/ls1028ardb-linux
====================

Acked-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: mscc: ocelot: don't hardcode the number of the CPU port

VSC7514 is a 10-port switch with 2 extra "CPU ports" (targets in the
queuing subsystem for terminating traffic locally).

There are 2 issues with hardcoding the CPU port as #10:
- It is not clear which snippets of the code are configuring something
  for one of the CPU ports, and which snippets are just doing something
  related to the number of physical ports.
- Actually any physical port can act as a CPU port connected to an
  external CPU (in addition to the local CPU). This is called NPI mode
  (Node Processor Interface) and is the way that the 6-port VSC9959
  (Felix) switch is integrated inside NXP LS1028A (the "local management
  CPU" functionality is not used there).

This patch makes it clear that the ocelot_bridge_stp_state_set function
operates on the CPU port (by making it an implicit member of the
bridging domain), and at the same time adds logic for the NPI port (aka
a physical port) to play the role of a CPU port (it shouldn't be part of
bridge_fwd_mask, as it's not explicitly enslaved to a bridge).

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: mscc: ocelot: split assignment of the cpu port into a separate function

Now that the places that configure routing destinations for the CPU port
have been marked as such, allow callers to specify their own CPU port
that is different than ocelot->num_phys_ports. A user will be the Felix
DSA driver, where the CPU port is one of the physical ports (NPI mode).

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: mscc: ocelot: refactor adjust_link into a netdev-independent function

This will be called from the Felix DSA frontend, which will work in
PHYLIB compatibility mode initially.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: mscc: ocelot: initialize list of multicast addresses in common code

This is just common path code that belongs to ocelot_init,
it has nothing to do with a specific SoC/board instance.

Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: mscc: ocelot: separate the common implementation of ndo_open and ndo_stop

Allow these functions to be called from the .port_enable and
.port_disable callbacks of DSA.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: mscc: ocelot: move port initialization into separate function

We need a function for the DSA front-end that does none of the
net_device registration, but initializes the hardware ports.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: mscc: ocelot: limit vlan ingress filtering to actual number of ports

The VSC7514 switch (Ocelot) is a 10-port device, while VSC9959 (Felix)
is 6-port. Therefore the VLAN filtering mask would be out of bounds when
calling for this new switch. Fix that.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: mscc: ocelot: refactor ethtool callbacks

Convert them into an implementation that can be called from DSA as well.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: mscc: ocelot: separate net_device related items out of ocelot_port

The ocelot and ocelot_port structures will be used by a new DSA driver,
so the ocelot_board.c file will have to allocate and work with a private
structure (ocelot_port_private), which embeds the generic struct
ocelot_port. This is because in DSA, at least one interface does not
have a net_device, and the DSA driver API does not interact with that
anyway.

The ocelot_port structure is equivalent to dsa_port, and ocelot to
dsa_switch. The members of ocelot_port which have an equivalent in
dsa_port (such as dp->vlan_filtering) have been moved to
ocelot_port_private.

We want to enforce the coding convention that "ocelot_port" refers to
the structure, and "port" refers to the integer index. One can retrieve
the structure at any time from ocelot->ports[port].

The patch is large but only contains variable renaming and mechanical
movement of fields from one structure to another.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: mscc: ocelot: refactor struct ocelot_port out of function prototypes

The ocelot_port structure has a net_device embedded in it, which makes
it unsuitable for leaving it in the driver implementation functions.

Leave ocelot_flower.c untouched. In that file, ocelot_port is used as an
interface to the tc shared blocks. That will be addressed in the next
patch.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: mscc: ocelot: change prototypes of switchdev port attribute handlers

This is needed so that the Felix DSA front-end can call the Ocelot
implementations.

The implementation of the "mc_disabled" switchdev attribute has also
been simplified by using the read-modify-write macro instead of
open-coding that operation.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: mscc: ocelot: change prototypes of hwtstamping ioctls

This is needed in order to present a simpler prototype to the DSA
front-end of ocelot.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: mscc: ocelot: break out fdb operations into abstract implementations

To be able to implement a DSA front-end over ocelot_fdb_add,
ocelot_fdb_del, ocelot_fdb_dump, these need to have a simple function
prototype that is independent of struct net_device, netlink skb, etc.

So rename the ndo ops of the ocelot driver into
ocelot_port_fdb_{add,del,dump}, and have them all call the abstract
implementations. At the same time, refactor ocelot_port_fdb_do_dump into
a function whose prototype is compatible with dsa_fdb_dump_cb_t, so that
the do_dump implementations can live together and be called by the
ocelot_fdb_dump through a function pointer.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: mscc: ocelot: break apart vlan operations into ocelot_vlan_{add, del}

We need an implementation of these functions that is agnostic to the
higher layer (switchdev or dsa).

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: mscc: ocelot: break apart ocelot_vlan_port_apply

This patch transforms the ocelot_vlan_port_apply function ("apply
what?") into 3 standalone functions:

- ocelot_port_vlan_filtering
- ocelot_port_set_native_vlan
- ocelot_port_set_pvid

These functions have a prototype that is better aligned to the DSA API.

The function also had some static initialization (TPID, drop frames with
multicast source MAC) which was not being changed from any place, so
that was just moved to ocelot_probe_port (one of the 6 callers of
ocelot_vlan_port_apply).

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'net-dsa-mv88e6xxx-Add-support-for-port-mirroring'

Iwan R Timmer says:

====================
net: dsa: mv88e6xxx: Add support for port mirroring

This patch series add support for port mirroring in the mv88e6xx switch driver.
The first patch changes the set_egress_port function to allow different egress
ports for egress and ingress traffic. The second patch adds the actual code for
port mirroring support.

Tested on a 88E6176 with:

tc qdisc add dev wan0 clsact
tc filter add dev wan0 ingress matchall skip_sw \
action mirred egress mirror dev lan2
tc filter add dev wan0 egress matchall skip_sw \
action mirred egress mirror dev lan3

Changes in v3

- Use enum for egress traffic direction
- Keep track of egress ports on mv88e6390
- Move booleans in struct for better structure packing

Changes in v2

- Support mirroring egress and ingress traffic to different ports
- Check for invalid configurations when multiple ports are mirrored
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: mv88e6xxx: Add support for port mirroring

Add support for configuring port mirroring through the cls_matchall
classifier. We do a full ingress and/or egress capture towards a
capture port. It allows setting a different capture port for ingress
and egress traffic.

It keeps track of the mirrored ports and the destination ports to
prevent changes to the capture port while other ports are being
mirrored.

Signed-off-by: Iwan R Timmer <irtimmer@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: mv88e6xxx: Split monitor port configuration

Separate the configuration of the egress and ingress monitor port.
This allows the port mirror functionality to do ingress and egress
port mirroring to separate ports.

Signed-off-by: Iwan R Timmer <irtimmer@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Support LAN743x PTP periodic output on any GPIO

The LAN743x Ethernet controller provides two independent PTP event
channels. Each one can be used to generate a periodic output from
the PTP clock. The output can be routed to any one of the available
GPIO pins on the device.

The PTP clock API can now be used to:
- select any LAN743x GPIO pin to function as a periodic output
- select either LAN743x PTP event channel to generate the output

The LAN7430 has 4 GPIO pins that are multiplexed with its internal
PHY LED control signals. A pin assigned to the LED control function
will be assigned to the GPIO function if selected for PTP periodic
output.

Signed-off-by: John Efstathiades <john.efstathiades@pebblebay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'Unlock-new-potential-in-SJA1105-with-PTP-system-timestamping'

Vladimir Oltean says:

====================
Unlock new potential in SJA1105 with PTP system timestamping

The SJA1105 being an automotive switch means it is designed to live in a
set-and-forget environment, far from the configure-at-runtime nature of
Linux. Frequently resetting the switch to change its static config means
it loses track of its PTP time, which is not good.

This patch series implements PTP system timestamping for this switch
(using the API introduced for SPI here:
https://www.mail-archive.com/netdev@vger.kernel.org/msg316725.html),
adding the following benefits to the driver:
- When under control of a user space PTP servo loop (ptp4l, phc2sys),
  the loss of sync during a switch reset is much more manageable, and
  the switch still remains in the s2 (locked servo) state.
- When synchronizing the switch using the software technique (based on
  reading clock A and writing the value to clock B, as opposed to
  relying on hardware timestamping), e.g. by using phc2sys, the sync
  accuracy is vastly improved due to the fact that the actual switch PTP
  time can now be more precisely correlated with something of better
  precision (CLOCK_REALTIME). The issue is that SPI transfers are
  inherently bad for measuring time with low jitter, but the newly
  introduced API aims to alleviate that issue somewhat.

This series is also a requirement for a future patch set that adds full
time-aware scheduling offload support for the switch.
====================

Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: Disallow management xmit during switch reset

The purpose here is to avoid ptp4l fail due to this condition:

  timed out while polling for tx timestamp
  increasing tx_timestamp_timeout may correct this issue, but it is likely caused by a driver bug
  port 1: send peer delay request failed

So either reset the switch before the management frame was sent, or
after it was timestamped as well, but not in the middle.

The condition may arise either due to a true timeout (i.e. because
re-uploading the static config takes time), or due to the TX timestamp
actually getting lost due to reset. For the former we can increase
tx_timestamp_timeout in userspace, for the latter we need this patch.

Locking all traffic during switch reset does not make sense at all,
though. Forcing all CPU-originated traffic to potentially block waiting
for a sleepable context to send > 800 bytes over SPI is not a good idea.
Flows that are autonomously forwarded by the switch will get dropped
anyway during switch reset no matter what. So just let all other
CPU-originated traffic be dropped as well.

Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: Restore PTP time after switch reset

The PTP time of the switch is not preserved when uploading a new static
configuration. Work around this hardware oddity by reading its PTP time
before a static config upload, and restoring it afterwards.

Static config changes are expected to occur at runtime even in scenarios
directly related to PTP, i.e. the Time-Aware Scheduler of the switch is
programmed in this way.

Perhaps the larger implication of this patch is that the PTP .gettimex64
and .settime functions need to be exposed to sja1105_main.c, where the
PTP lock needs to be held during this entire process. So their core
implementation needs to move to some common functions which get exposed
in sja1105_ptp.h.

Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: Implement the .gettimex64 system call for PTP

Through the PTP_SYS_OFFSET_EXTENDED ioctl, it is possible for userspace
applications (i.e. phc2sys) to compensate for the delays incurred while
reading the PHC's time.

The task itself of taking the software timestamp is delegated to the SPI
subsystem, through the newly introduced API in struct spi_transfer. The
goal is to cross-timestamp I/O operations on the switch's PTP clock with
values in the local system clock (CLOCK_REALTIME). For that we need to
understand a bit of the hardware internals.

The 'read PTP time' message is a 12 byte structure, first 4 bytes of
which represent the SPI header, and the last 8 bytes represent the
64-bit PTP time. The switch itself starts processing the command
immediately after receiving the last bit of the address, i.e. at the
middle of byte 3 (last byte of header). The PTP time is shadowed to a
buffer register in the switch, and retrieved atomically during the
subsequent SPI frames.

A similar thing goes on for the 'write PTP time' message, although in
that case the switch waits until the 64-bit PTP time becomes fully
available before taking any action. So the byte that needs to be
software-timestamped is byte 11 (last) of the transfer.

The patch creates a common (and local) sja1105_xfer implementation for
the SPI I/O, and offers 3 front-ends:

- sja1105_xfer_u32 and sja1105_xfer_u64: these are capable of optionally
  requesting a PTP timestamp

- sja1105_xfer_buf: this is for large transfers (e.g. the static config
  buffer) and other misc data, and there is no point in giving
  timestamping capabilities to this.

Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'r8169-improve-PHY-configuration'

Heiner Kallweit says:

====================
r8169: improve PHY configuration

This series adds helpers to improve and simplify the PHY
configuration on various network chip versions.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

r8169: remove rtl8168c_4_hw_phy_config

rtl8168c_4_hw_phy_config() duplicates rtl8168c_3_hw_phy_config(),
so we can remove the function.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

r8169: add helper r8168d_modify_extpage

Certain integrated PHY's from RTL8168d support extended pages. On page
0x0007 the number of the extended page is written to register 0x1e,
then the registers on the extended page can be accessed. Add a helper
for this to improve readability and simplify the code.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

r8169: switch to phylib functions in more places

Use the phylib MDIO access functions in more places to simplify
the code.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

r8169: add helper r8168d_phy_param

Integrated PHY's from RTL8168d support an indirect access method for
PHY parameters. On page 0x0005 parameter number is written to register
0x05, then the parameter can be accessed via register 0x06.
Add a helper for this to improve readability and simplify the code.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

r8169: add helper r8168g_phy_param

Integrated PHY's from RTL8168g support an indirect access method for
PHY parameters. On page 0x0a43 parameter number is written to register
0x13, then the parameter can be accessed via register 0x14.
Add a helper for this to improve readability and simplify the code.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: sfp: rework upstream interface

The current upstream interface is an all-or-nothing, which is
sub-optimal for future changes, as it doesn't allow the upstream driver
to prepare for the SFP module becoming available, as it is at boot.

Switch to a find-sfp-bus, add-upstream, del-upstream, put-sfp-bus
interface structure instead, which allows the upstream driver to
prepare for a module being available as soon as add-upstream is called.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge git://git./linux/kernel/git/netdev/net

One conflict in the BPF samples Makefile, some fixes in 'net' whilst
we were converting over to Makefile.target rules in 'net-next'.

Signed-off-by: David S. Miller <davem@davemloft.net>

Merge git://git./linux/kernel/git/netdev/net

Pull networking fixes from David Miller:

1) BPF sample build fixes from Björn Töpel

2) Fix powerpc bpf tail call implementation, from Eric Dumazet.

3) DCCP leaks jiffies on the wire, fix also from Eric Dumazet.

4) Fix crash in ebtables when using dnat target, from Florian Westphal.

5) Fix port disable handling whne removing bcm_sf2 driver, from Florian
    Fainelli.

6) Fix kTLS sk_msg trim on fallback to copy mode, from Jakub Kicinski.

7) Various KCSAN fixes all over the networking, from Eric Dumazet.

8) Memory leaks in mlx5 driver, from Alex Vesker.

9) SMC interface refcounting fix, from Ursula Braun.

10) TSO descriptor handling fixes in stmmac driver, from Jose Abreu.

11) Add a TX lock to synchonize the kTLS TX path properly with crypto
    operations. From Jakub Kicinski.

12) Sock refcount during shutdown fix in vsock/virtio code, from Stefano
    Garzarella.

13) Infinite loop in Intel ice driver, from Colin Ian King.

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (108 commits)
  ixgbe: need_wakeup flag might not be set for Tx
  i40e: need_wakeup flag might not be set for Tx
  igb/igc: use ktime accessors for skb->tstamp
  i40e: Fix for ethtool -m issue on X722 NIC
  iavf: initialize ITRN registers with correct values
  ice: fix potential infinite loop because loop counter being too small
  qede: fix NULL pointer deref in __qede_remove()
  net: fix data-race in neigh_event_send()
  vsock/virtio: fix sock refcnt holding during the shutdown
  net: ethernet: octeon_mgmt: Account for second possible VLAN header
  mac80211: fix station inactive_time shortly after boot
  net/fq_impl: Switch to kvmalloc() for memory allocation
  mac80211: fix ieee80211_txq_setup_flows() failure path
  ipv4: Fix table id reference in fib_sync_down_addr
  ipv6: fixes rt6_probe() and fib6_nh->last_probe init
  net: hns: Fix the stray netpoll locks causing deadlock in NAPI path
  net: usb: qmi_wwan: add support for DW5821e with eSIM support
  CDC-NCM: handle incomplete transfer of MTU
  nfc: netlink: fix double device reference drop
  NFC: st21nfca: fix double free
  ...

Merge tag 'for-linus-2019-11-08' of git://git.kernel.dk/linux-block

Pull block fixes from Jens Axboe:

- Two NVMe device removal crash fixes, and a compat fixup for for an
   ioctl that was introduced in this release (Anton, Charles, Max - via
   Keith)

- Missing error path mutex unlock for drbd (Dan)

- cgroup writeback fixup on dead memcg (Tejun)

- blkcg online stats print fix (Tejun)

* tag 'for-linus-2019-11-08' of git://git.kernel.dk/linux-block:
  cgroup,writeback: don't switch wbs immediately on dead wbs if the memcg is dead
  block: drbd: remove a stray unlock in __drbd_send_protocol()
  blkcg: make blkcg_print_stat() print stats only for online blkgs
  nvme: change nvme_passthru_cmd64 to explicitly mark rsvd
  nvme-multipath: fix crash in nvme_mpath_clear_ctrl_paths
  nvme-rdma: fix a segmentation fault during module unload

Merge branch '40GbE' of git://git./linux/kernel/git/jkirsher/net-queue

Jeff Kirsher says:

====================
Intel Wired LAN Driver Fixes 2019-11-08

This series contains fixes to igb, igc, ixgbe, i40e, iavf and ice
drivers.

Colin Ian King fixes a potentially wrap-around counter in a for-loop.

Nick fixes the default ITR values for the iavf driver to 50 usecs
interval.

Arkadiusz fixes 'ethtool -m' for X722 devices where the correct value
cannot be obtained from the firmware, so add X722 to the check to ensure
the wrong value is not returned.

Jake fixes igb and igc drivers in their implementation of launch time
support by declaring skb->tstamp value as ktime_t instead of s64.

Magnus fixes ixgbe and i40e where the need_wakeup flag for transmit may
not be set for AF_XDP sockets that are only used to send packets.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

ixgbe: need_wakeup flag might not be set for Tx

The need_wakeup flag for Tx might not be set for AF_XDP sockets that
are only used to send packets. This happens if there is at least one
outstanding packet that has not been completed by the hardware and we
get that corresponding completion (which will not generate an
interrupt since interrupts are disabled in the napi poll loop) between
the time we stopped processing the Tx completions and interrupts are
enabled again. In this case, the need_wakeup flag will have been
cleared at the end of the Tx completion processing as we believe we
will get an interrupt from the outstanding completion at a later point
in time. But if this completion interrupt occurs before interrupts
are enable, we lose it and should at that point really have set the
need_wakeup flag since there are no more outstanding completions that
can generate an interrupt to continue the processing. When this
happens, user space will see a Tx queue need_wakeup of 0 and skip
issuing a syscall, which means will never get into the Tx processing
again and we have a deadlock.

This patch introduces a quick fix for this issue by just setting the
need_wakeup flag for Tx to 1 all the time. I am working on a proper
fix for this that will toggle the flag appropriately, but it is more
challenging than I anticipated and I am afraid that this patch will
not be completed before the merge window closes, therefore this easier
fix for now. This fix has a negative performance impact in the range
of 0% to 4%. Towards the higher end of the scale if you have driver
and application on the same core and issue a lot of packets, and
towards no negative impact if you use two cores, lower transmission
speeds and/or a workload that also receives packets.

Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: need_wakeup flag might not be set for Tx

The need_wakeup flag for Tx might not be set for AF_XDP sockets that
are only used to send packets. This happens if there is at least one
outstanding packet that has not been completed by the hardware and we
get that corresponding completion (which will not generate an
interrupt since interrupts are disabled in the napi poll loop) between
the time we stopped processing the Tx completions and interrupts are
enabled again. In this case, the need_wakeup flag will have been
cleared at the end of the Tx completion processing as we believe we
will get an interrupt from the outstanding completion at a later point
in time. But if this completion interrupt occurs before interrupts
are enable, we lose it and should at that point really have set the
need_wakeup flag since there are no more outstanding completions that
can generate an interrupt to continue the processing. When this
happens, user space will see a Tx queue need_wakeup of 0 and skip
issuing a syscall, which means will never get into the Tx processing
again and we have a deadlock.

This patch introduces a quick fix for this issue by just setting the
need_wakeup flag for Tx to 1 all the time. I am working on a proper
fix for this that will toggle the flag appropriately, but it is more
challenging than I anticipated and I am afraid that this patch will
not be completed before the merge window closes, therefore this easier
fix for now. This fix has a negative performance impact in the range
of 0% to 4%. Towards the higher end of the scale if you have driver
and application on the same core and issue a lot of packets, and
towards no negative impact if you use two cores, lower transmission
speeds and/or a workload that also receives packets.

Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

igb/igc: use ktime accessors for skb->tstamp

When implementing launch time support in the igb and igc drivers, the
skb->tstamp value is assumed to be a s64, but it's declared as a ktime_t
value.

Although ktime_t is typedef'd to s64 it wasn't always, and the kernel
provides accessors for ktime_t values.

Use the ktime_to_timespec64 and ktime_set accessors instead of directly
assuming that the variable is always an s64.

This improves portability if the code is ever moved to another kernel
version, or if the definition of ktime_t ever changes again in the
future.

Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: Fix for ethtool -m issue on X722 NIC

This patch contains fix for a problem with command:
'ethtool -m <dev>'
which breaks functionality of:
'ethtool <dev>'
when called on X722 NIC

Disallowed update of link phy_types on X722 NIC
Currently correct value cannot be obtained from FW
Previously wrong value returned by FW was used and was
a root cause for incorrect output of 'ethtool <dev>' command

Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

iavf: initialize ITRN registers with correct values

Since commit 92418fb14750 ("i40e/i40evf: Use usec value instead of reg
value for ITR defines") the driver tracks the interrupt throttling
intervals in single usec units, although the actual ITRN registers are
programmed in 2 usec units. Most register programming flows in the driver
correctly handle the conversion, although it is currently not applied when
the registers are initialized to their default values. Most of the time
this doesn't present a problem since the default values are usually
immediately overwritten through the standard adaptive throttling mechanism,
or updated manually by the user, but if adaptive throttling is disabled and
the interval values are left alone then the incorrect value will persist.

Since the intended default interval of 50 usecs (vs. 100 usecs as
programmed) performs better for most traffic workloads, this can lead to
performance regressions.

This patch adds the correct conversion when writing the initial values to
the ITRN registers.

Signed-off-by: Nicholas Nunley <nicholas.d.nunley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: fix potential infinite loop because loop counter being too small

Currently the for-loop counter i is a u8 however it is being checked
against a maximum value hw->num_tx_sched_layers which is a u16. Hence
there is a potential wrap-around of counter i back to zero if
hw->num_tx_sched_layers is greater than 255. Fix this by making i
a u16.

Addresses-Coverity: ("Infinite loop")
Fixes: b36c598c999c ("ice: Updates to Tx scheduler code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Merge branch 'sctp-rfc7829'

Xin Long says:

====================
sctp: update from rfc7829

SCTP-PF was implemented based on a Internet-Draft in 2012:

  https://tools.ietf.org/html/draft-nishida-tsvwg-sctp-failover-05

It's been updated quite a few by rfc7829 in 2016.

This patchset adds the following features:

  1. add SCTP_ADDR_POTENTIALLY_FAILED notification
  2. add pf_expose per netns/sock/asoc
  3. add SCTP_EXPOSE_POTENTIALLY_FAILED_STATE sockopt
  4. add ps_retrans per netns/sock/asoc/transport
     (Primary Path Switchover)
  5. add spt_pathcpthld for SCTP_PEER_ADDR_THLDS sockopt

v1->v2:
  - See Patch 2/5 and Patch 5/5.
v2->v3:
  - See Patch 1/5, 2/5 and 3/5.
v3->v4:
  - See Patch 1/5, 2/5, 3/5 and 4/5.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: add SCTP_PEER_ADDR_THLDS_V2 sockopt

Section 7.2 of rfc7829: "Peer Address Thresholds (SCTP_PEER_ADDR_THLDS)
Socket Option" extends 'struct sctp_paddrthlds' with 'spt_pathcpthld'
added to allow a user to change ps_retrans per sock/asoc/transport, as
other 2 paddrthlds: pf_retrans, pathmaxrxt.

Note: to not break the user's program, here to support pf_retrans dump
and setting by adding a new sockopt SCTP_PEER_ADDR_THLDS_V2, and a new
structure sctp_paddrthlds_v2 instead of extending sctp_paddrthlds.

Also, when setting ps_retrans, the value is not allowed to be greater
than pf_retrans.

v1->v2:
- use SCTP_PEER_ADDR_THLDS_V2 to set/get pf_retrans instead,
as Marcelo and David Laight suggested.

Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: add support for Primary Path Switchover

This is a new feature defined in section 5 of rfc7829: "Primary Path
Switchover". By introducing a new tunable parameter:

  Primary.Switchover.Max.Retrans (PSMR)

The primary path will be changed to another active path when the path
error counter on the old primary path exceeds PSMR, so that "the SCTP
sender is allowed to continue data transmission on a new working path
even when the old primary destination address becomes active again".

This patch is to add this tunable parameter, 'ps_retrans' per netns,
sock, asoc and transport. It also allows a user to change ps_retrans
per netns by sysctl, and ps_retrans per sock/asoc/transport will be
initialized with it.

The check will be done in sctp_do_8_2_transport_strike() when this
feature is enabled.

Note this feature is disabled by initializing 'ps_retrans' per netns
as 0xffff by default, and its value can't be less than 'pf_retrans'
when changing by sysctl.

v3->v4:
  - add define SCTP_PS_RETRANS_MAX 0xffff, and use it on extra2 of
    sysctl 'ps_retrans'.
  - add a new entry for ps_retrans on ip-sysctl.txt.

Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: add SCTP_EXPOSE_POTENTIALLY_FAILED_STATE sockopt

This is a sockopt defined in section 7.3 of rfc7829: "Exposing
the Potentially Failed Path State", by which users can change
pf_expose per sock and asoc.

The new sockopt SCTP_EXPOSE_POTENTIALLY_FAILED_STATE is also
known as SCTP_EXPOSE_PF_STATE for short.

v2->v3:
  - return -EINVAL if params.assoc_value > SCTP_PF_EXPOSE_MAX.
  - define SCTP_EXPOSE_PF_STATE SCTP_EXPOSE_POTENTIALLY_FAILED_STATE.
v3->v4:
  - improve changelog.

Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: add SCTP_ADDR_POTENTIALLY_FAILED notification

SCTP Quick failover draft section 5.1, point 5 has been removed
from rfc7829. Instead, "the sender SHOULD (i) notify the Upper
Layer Protocol (ULP) about this state transition", as said in
section 3.2, point 8.

So this patch is to add SCTP_ADDR_POTENTIALLY_FAILED, defined
in section 7.1, "which is reported if the affected address
becomes PF". Also remove transport cwnd's update when moving
from PF back to ACTIVE , which is no longer in rfc7829 either.

Note that ulp_notify will be set to false if asoc->expose is
not 'enabled', according to last patch.

v2->v3:
  - define SCTP_ADDR_PF SCTP_ADDR_POTENTIALLY_FAILED.
v3->v4:
  - initialize spc_state with SCTP_ADDR_AVAILABLE, as Marcelo suggested.
  - check asoc->pf_expose in sctp_assoc_control_transport(), as Marcelo
    suggested.

Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: add pf_expose per netns and sock and asoc

As said in rfc7829, section 3, point 12:

  The SCTP stack SHOULD expose the PF state of its destination
  addresses to the ULP as well as provide the means to notify the
  ULP of state transitions of its destination addresses from
  active to PF, and vice versa.  However, it is recommended that
  an SCTP stack implementing SCTP-PF also allows for the ULP to be
  kept ignorant of the PF state of its destinations and the
  associated state transitions, thus allowing for retention of the
  simpler state transition model of [RFC4960] in the ULP.

Not only does it allow to expose the PF state to ULP, but also
allow to ignore sctp-pf to ULP.

So this patch is to add pf_expose per netns, sock and asoc. And in
sctp_assoc_control_transport(), ulp_notify will be set to false if
asoc->expose is not 'enabled' in next patch.

It also allows a user to change pf_expose per netns by sysctl, and
pf_expose per sock and asoc will be initialized with it.

Note that pf_expose also works for SCTP_GET_PEER_ADDR_INFO sockopt,
to not allow a user to query the state of a sctp-pf peer address
when pf_expose is 'disabled', as said in section 7.3.

v1->v2:
  - Fix a build warning noticed by Nathan Chancellor.
v2->v3:
  - set pf_expose to UNUSED by default to keep compatible with old
    applications.
v3->v4:
  - add a new entry for pf_expose on ip-sysctl.txt, as Marcelo suggested.
  - change this patch to 1/5, and move sctp_assoc_control_transport
    change into 2/5, as Marcelo suggested.
  - use SCTP_PF_EXPOSE_UNSET instead of SCTP_PF_EXPOSE_UNUSED, and
    set SCTP_PF_EXPOSE_UNSET to 0 in enum, as Marcelo suggested.

Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

devlink: disallow reload operation during device cleanup

There is a race between driver code that does setup/cleanup of device
and devlink reload operation that in some drivers works with the same
code. Use after free could we easily obtained by running:

while true; do
        echo 10 > /sys/bus/netdevsim/new_device
        devlink dev reload netdevsim/netdevsim10 &
        echo 10 > /sys/bus/netdevsim/del_device
done

Fix this by enabling reload only after setup of device is complete and
disabling it at the beginning of the cleanup process.

Reported-by: Ido Schimmel <idosch@mellanox.com>
Fixes: 2d8dc5bbf4e7 ("devlink: Add support for reload")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

selftest: net: add alternative names test

Add a simple test for recently added netdevice alternative names.

Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: fix NULL pointer deref in __qede_remove()

While rebooting the system with SR-IOV vfs enabled leads
to below crash due to recurrence of __qede_remove() on the VF
devices (first from .shutdown() flow of the VF itself and
another from PF's .shutdown() flow executing pci_disable_sriov())

This patch adds a safeguard in __qede_remove() flow to fix this,
so that driver doesn't attempt to remove "already removed" devices.

[  194.360134] BUG: unable to handle kernel NULL pointer dereference at 00000000000008dc
[  194.360227] IP: [<ffffffffc03553c4>] __qede_remove+0x24/0x130 [qede]
[  194.360304] PGD 0
[  194.360325] Oops: 0000 [#1] SMP
[  194.360360] Modules linked in: tcp_lp fuse tun bridge stp llc devlink bonding ip_set nfnetlink ib_isert iscsi_target_mod ib_srpt target_core_mod ib_srp scsi_transport_srp scsi_tgt ib_ipoib ib_umad rpcrdma sunrpc rdma_ucm ib_uverbs ib_iser rdma_cm iw_cm ib_cm libiscsi scsi_transport_iscsi dell_smbios iTCO_wdt iTCO_vendor_support dell_wmi_descriptor dcdbas vfat fat pcc_cpufreq skx_edac intel_powerclamp coretemp intel_rapl iosf_mbi kvm_intel kvm irqbypass crc32_pclmul ghash_clmulni_intel aesni_intel lrw gf128mul glue_helper ablk_helper cryptd qedr ib_core pcspkr ses enclosure joydev ipmi_ssif sg i2c_i801 lpc_ich mei_me mei wmi ipmi_si ipmi_devintf ipmi_msghandler tpm_crb acpi_pad acpi_power_meter xfs libcrc32c sd_mod crc_t10dif crct10dif_generic crct10dif_pclmul crct10dif_common crc32c_intel mgag200
[  194.361044]  qede i2c_algo_bit drm_kms_helper qed syscopyarea sysfillrect nvme sysimgblt fb_sys_fops ttm nvme_core mpt3sas crc8 ptp drm pps_core ahci raid_class scsi_transport_sas libahci libata drm_panel_orientation_quirks nfit libnvdimm dm_mirror dm_region_hash dm_log dm_mod [last unloaded: ip_tables]
[  194.361297] CPU: 51 PID: 7996 Comm: reboot Kdump: loaded Not tainted 3.10.0-1062.el7.x86_64 #1
[  194.361359] Hardware name: Dell Inc. PowerEdge MX840c/0740HW, BIOS 2.4.6 10/15/2019
[  194.361412] task: ffff9cea9b360000 ti: ffff9ceabebdc000 task.ti: ffff9ceabebdc000
[  194.361463] RIP: 0010:[<ffffffffc03553c4>]  [<ffffffffc03553c4>] __qede_remove+0x24/0x130 [qede]
[  194.361534] RSP: 0018:ffff9ceabebdfac0  EFLAGS: 00010282
[  194.361570] RAX: 0000000000000000 RBX: ffff9cd013846098 RCX: 0000000000000000
[  194.361621] RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff9cd013846098
[  194.361668] RBP: ffff9ceabebdfae8 R08: 0000000000000000 R09: 0000000000000000
[  194.361715] R10: 00000000bfe14201 R11: ffff9ceabfe141e0 R12: 0000000000000000
[  194.361762] R13: ffff9cd013846098 R14: 0000000000000000 R15: ffff9ceab5e48000
[  194.361810] FS:  00007f799c02d880(0000) GS:ffff9ceacb0c0000(0000) knlGS:0000000000000000
[  194.361865] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  194.361903] CR2: 00000000000008dc CR3: 0000001bdac76000 CR4: 00000000007607e0
[  194.361953] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[  194.362002] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[  194.362051] PKRU: 55555554
[  194.362073] Call Trace:
[  194.362109]  [<ffffffffc0355500>] qede_remove+0x10/0x20 [qede]
[  194.362180]  [<ffffffffb97d0f3e>] pci_device_remove+0x3e/0xc0
[  194.362240]  [<ffffffffb98b3c52>] __device_release_driver+0x82/0xf0
[  194.362285]  [<ffffffffb98b3ce3>] device_release_driver+0x23/0x30
[  194.362343]  [<ffffffffb97c86d4>] pci_stop_bus_device+0x84/0xa0
[  194.362388]  [<ffffffffb97c87e2>] pci_stop_and_remove_bus_device+0x12/0x20
[  194.362450]  [<ffffffffb97f153f>] pci_iov_remove_virtfn+0xaf/0x160
[  194.362496]  [<ffffffffb97f1aec>] sriov_disable+0x3c/0xf0
[  194.362534]  [<ffffffffb97f1bc3>] pci_disable_sriov+0x23/0x30
[  194.362599]  [<ffffffffc02f83c3>] qed_sriov_disable+0x5e3/0x650 [qed]
[  194.362658]  [<ffffffffb9622df6>] ? kfree+0x106/0x140
[  194.362709]  [<ffffffffc02cc0c0>] ? qed_free_stream_mem+0x70/0x90 [qed]
[  194.362754]  [<ffffffffb9622df6>] ? kfree+0x106/0x140
[  194.362803]  [<ffffffffc02cd659>] qed_slowpath_stop+0x1a9/0x1d0 [qed]
[  194.362854]  [<ffffffffc035544e>] __qede_remove+0xae/0x130 [qede]
[  194.362904]  [<ffffffffc03554e0>] qede_shutdown+0x10/0x20 [qede]
[  194.362956]  [<ffffffffb97cf90a>] pci_device_shutdown+0x3a/0x60
[  194.363010]  [<ffffffffb98b180b>] device_shutdown+0xfb/0x1f0
[  194.363066]  [<ffffffffb94b66c6>] kernel_restart_prepare+0x36/0x40
[  194.363107]  [<ffffffffb94b66e2>] kernel_restart+0x12/0x60
[  194.363146]  [<ffffffffb94b6959>] SYSC_reboot+0x229/0x260
[  194.363196]  [<ffffffffb95f200d>] ? handle_mm_fault+0x39d/0x9b0
[  194.363253]  [<ffffffffb942b621>] ? __switch_to+0x151/0x580
[  194.363304]  [<ffffffffb9b7ec28>] ? __schedule+0x448/0x9c0
[  194.363343]  [<ffffffffb94b69fe>] SyS_reboot+0xe/0x10
[  194.363387]  [<ffffffffb9b8bede>] system_call_fastpath+0x25/0x2a
[  194.363430] Code: f9 e9 37 ff ff ff 90 0f 1f 44 00 00 55 48 89 e5 41 57 41 56 41 55 4c 8d af 98 00 00 00 41 54 4c 89 ef 41 89 f4 53 e8 4c e4 55 f9 <80> b8 dc 08 00 00 01 48 89 c3 4c 8d b8 c0 08 00 00 4c 8b b0 c0
[  194.363712] RIP  [<ffffffffc03553c4>] __qede_remove+0x24/0x130 [qede]
[  194.363764]  RSP <ffff9ceabebdfac0>
[  194.363791] CR2: 00000000000008dc

Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Sudarsana Kalluru <skalluru@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

packet: fix data-race in fanout_flow_is_huge()

KCSAN reported the following data-race [1]

Adding a couple of READ_ONCE()/WRITE_ONCE() should silence it.

Since the report hinted about multiple cpus using the history
concurrently, I added a test avoiding writing on it if the
victim slot already contains the desired value.

[1]

BUG: KCSAN: data-race in fanout_demux_rollover / fanout_demux_rollover

read to 0xffff8880b01786cc of 4 bytes by task 18921 on cpu 1:
fanout_flow_is_huge net/packet/af_packet.c:1303 [inline]
fanout_demux_rollover+0x33e/0x3f0 net/packet/af_packet.c:1353
packet_rcv_fanout+0x34e/0x490 net/packet/af_packet.c:1453
deliver_skb net/core/dev.c:1888 [inline]
dev_queue_xmit_nit+0x15b/0x540 net/core/dev.c:1958
xmit_one net/core/dev.c:3195 [inline]
dev_hard_start_xmit+0x3f5/0x430 net/core/dev.c:3215
__dev_queue_xmit+0x14ab/0x1b40 net/core/dev.c:3792
dev_queue_xmit+0x21/0x30 net/core/dev.c:3825
neigh_direct_output+0x1f/0x30 net/core/neighbour.c:1530
neigh_output include/net/neighbour.h:511 [inline]
ip6_finish_output2+0x7a2/0xec0 net/ipv6/ip6_output.c:116
__ip6_finish_output net/ipv6/ip6_output.c:142 [inline]
__ip6_finish_output+0x2d7/0x330 net/ipv6/ip6_output.c:127
ip6_finish_output+0x41/0x160 net/ipv6/ip6_output.c:152
NF_HOOK_COND include/linux/netfilter.h:294 [inline]
ip6_output+0xf2/0x280 net/ipv6/ip6_output.c:175
dst_output include/net/dst.h:436 [inline]
ip6_local_out+0x74/0x90 net/ipv6/output_core.c:179
ip6_send_skb+0x53/0x110 net/ipv6/ip6_output.c:1795
udp_v6_send_skb.isra.0+0x3ec/0xa70 net/ipv6/udp.c:1173
udpv6_sendmsg+0x1906/0x1c20 net/ipv6/udp.c:1471
inet6_sendmsg+0x6d/0x90 net/ipv6/af_inet6.c:576
sock_sendmsg_nosec net/socket.c:637 [inline]
sock_sendmsg+0x9f/0xc0 net/socket.c:657
___sys_sendmsg+0x2b7/0x5d0 net/socket.c:2311
__sys_sendmmsg+0x123/0x350 net/socket.c:2413
__do_sys_sendmmsg net/socket.c:2442 [inline]
__se_sys_sendmmsg net/socket.c:2439 [inline]
__x64_sys_sendmmsg+0x64/0x80 net/socket.c:2439
do_syscall_64+0xcc/0x370 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x44/0xa9

write to 0xffff8880b01786cc of 4 bytes by task 18922 on cpu 0:
fanout_flow_is_huge net/packet/af_packet.c:1306 [inline]
fanout_demux_rollover+0x3a4/0x3f0 net/packet/af_packet.c:1353
packet_rcv_fanout+0x34e/0x490 net/packet/af_packet.c:1453
deliver_skb net/core/dev.c:1888 [inline]
dev_queue_xmit_nit+0x15b/0x540 net/core/dev.c:1958
xmit_one net/core/dev.c:3195 [inline]
dev_hard_start_xmit+0x3f5/0x430 net/core/dev.c:3215
__dev_queue_xmit+0x14ab/0x1b40 net/core/dev.c:3792
dev_queue_xmit+0x21/0x30 net/core/dev.c:3825
neigh_direct_output+0x1f/0x30 net/core/neighbour.c:1530
neigh_output include/net/neighbour.h:511 [inline]
ip6_finish_output2+0x7a2/0xec0 net/ipv6/ip6_output.c:116
__ip6_finish_output net/ipv6/ip6_output.c:142 [inline]
__ip6_finish_output+0x2d7/0x330 net/ipv6/ip6_output.c:127
ip6_finish_output+0x41/0x160 net/ipv6/ip6_output.c:152
NF_HOOK_COND include/linux/netfilter.h:294 [inline]
ip6_output+0xf2/0x280 net/ipv6/ip6_output.c:175
dst_output include/net/dst.h:436 [inline]
ip6_local_out+0x74/0x90 net/ipv6/output_core.c:179
ip6_send_skb+0x53/0x110 net/ipv6/ip6_output.c:1795
udp_v6_send_skb.isra.0+0x3ec/0xa70 net/ipv6/udp.c:1173
udpv6_sendmsg+0x1906/0x1c20 net/ipv6/udp.c:1471
inet6_sendmsg+0x6d/0x90 net/ipv6/af_inet6.c:576
sock_sendmsg_nosec net/socket.c:637 [inline]
sock_sendmsg+0x9f/0xc0 net/socket.c:657
___sys_sendmsg+0x2b7/0x5d0 net/socket.c:2311
__sys_sendmmsg+0x123/0x350 net/socket.c:2413
__do_sys_sendmmsg net/socket.c:2442 [inline]
__se_sys_sendmmsg net/socket.c:2439 [inline]
__x64_sys_sendmmsg+0x64/0x80 net/socket.c:2439
do_syscall_64+0xcc/0x370 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x44/0xa9

Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 18922 Comm: syz-executor.3 Not tainted 5.4.0-rc6+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011

Fixes: 3b3a5b0aab5b ("packet: rollover huge flows before small flows")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'TIPC-Encryption'

Tuong Lien says:

====================
TIPC Encryption

This series provides TIPC encryption feature, kernel part. There will be
another one in the 'iproute2/tipc' for user space to set key.

v2: add select crypto 'aes(gcm)' for TIPC_CRYPTO in Kconfig
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: add support for AEAD key setting via netlink

This commit adds two netlink commands to TIPC in order for user to be
able to set or remove AEAD keys:
- TIPC_NL_KEY_SET
- TIPC_NL_KEY_FLUSH

When the 'KEY_SET' is given along with the key data, the key will be
initiated and attached to TIPC crypto. On the other hand, the
'KEY_FLUSH' command will remove all existing keys if any.

Acked-by: Ying Xue <ying.xue@windreiver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: introduce TIPC encryption & authentication

This commit offers an option to encrypt and authenticate all messaging,
including the neighbor discovery messages. The currently most advanced
algorithm supported is the AEAD AES-GCM (like IPSec or TLS). All
encryption/decryption is done at the bearer layer, just before leaving
or after entering TIPC.

Supported features:
- Encryption & authentication of all TIPC messages (header + data);
- Two symmetric-key modes: Cluster and Per-node;
- Automatic key switching;
- Key-expired revoking (sequence number wrapped);
- Lock-free encryption/decryption (RCU);
- Asynchronous crypto, Intel AES-NI supported;
- Multiple cipher transforms;
- Logs & statistics;

Two key modes:
- Cluster key mode: One single key is used for both TX & RX in all
nodes in the cluster.
- Per-node key mode: Each nodes in the cluster has one specific TX key.
For RX, a node requires its peers' TX key to be able to decrypt the
messages from those peers.

Key setting from user-space is performed via netlink by a user program
(e.g. the iproute2 'tipc' tool).

Internal key state machine:

                                 Attach    Align(RX)
                                     +-+   +-+
                                     | V   | V
        +---------+      Attach     +---------+
        |  IDLE   |---------------->| PENDING |(user = 0)
        +---------+                 +---------+
           A   A                   Switch|  A
           |   |                         |  |
           |   | Free(switch/revoked)    |  |
     (Free)|   +----------------------+  |  |Timeout
           |              (TX)        |  |  |(RX)
           |                          |  |  |
           |                          |  v  |
        +---------+      Switch     +---------+
        | PASSIVE |<----------------| ACTIVE  |
        +---------+       (RX)      +---------+
        (user = 1)                  (user >= 1)

The number of TFMs is 10 by default and can be changed via the procfs
'net/tipc/max_tfms'. At this moment, as for simplicity, this file is
also used to print the crypto statistics at runtime:

echo 0xfff1 > /proc/sys/net/tipc/max_tfms

The patch defines a new TIPC version (v7) for the encryption message (-
backward compatibility as well). The message is basically encapsulated
as follows:

   +----------------------------------------------------------+
   | TIPCv7 encryption  | Original TIPCv2    | Authentication |
   | header             | packet (encrypted) | Tag            |
   +----------------------------------------------------------+

The throughput is about ~40% for small messages (compared with non-
encryption) and ~9% for large messages. With the support from hardware
crypto i.e. the Intel AES-NI CPU instructions, the throughput increases
upto ~85% for small messages and ~55% for large messages.

By default, the new feature is inactive (i.e. no encryption) until user
sets a key for TIPC. There is however also a new option - "TIPC_CRYPTO"
in the kernel configuration to enable/disable the new code when needed.

MAINTAINERS | add two new files 'crypto.h' & 'crypto.c' in tipc

Acked-by: Ying Xue <ying.xue@windreiver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: add new AEAD key structure for user API

The new structure 'tipc_aead_key' is added to the 'tipc.h' for user to
be able to transfer a key to TIPC in kernel. Netlink will be used for
this purpose in the later commits.

Acked-by: Ying Xue <ying.xue@windreiver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: enable creating a "preliminary" node

When user sets RX key for a peer not existing on the own node, a new
node entry is needed to which the RX key will be attached. However,
since the peer node address (& capabilities) is unknown at that moment,
only the node-ID is provided, this commit allows the creation of a node
with only the data that we call as “preliminary”.

A preliminary node is not the object of the “tipc_node_find()” but the
“tipc_node_find_by_id()”. Once the first message i.e. LINK_CONFIG comes
from that peer, and is successfully decrypted by the own node, the
actual peer node data will be properly updated and the node will
function as usual.

In addition, the node timer always starts when a node object is created
so if a preliminary node is not used, it will be cleaned up.

The later encryption functions will also use the node timer and be able
to create a preliminary node automatically when needed.

Acked-by: Ying Xue <ying.xue@windreiver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: add reference counter to bearer

As a need to support the crypto asynchronous operations in the later
commits, apart from the current RCU mechanism for bearer pointer, we
add a 'refcnt' to the bearer object as well.

So, a bearer can be hold via 'tipc_bearer_hold()' without being freed
even though the bearer or interface can be disabled in the meanwhile.
If that happens, the bearer will be released then when the crypto
operation is completed and 'tipc_bearer_put()' is called.

Acked-by: Ying Xue <ying.xue@windreiver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fix data-race in neigh_event_send()

KCSAN reported the following data-race [1]

The fix will also prevent the compiler from optimizing out
the condition.

[1]

BUG: KCSAN: data-race in neigh_resolve_output / neigh_resolve_output

write to 0xffff8880a41dba78 of 8 bytes by interrupt on cpu 1:
neigh_event_send include/net/neighbour.h:443 [inline]
neigh_resolve_output+0x78/0x480 net/core/neighbour.c:1474
neigh_output include/net/neighbour.h:511 [inline]
ip_finish_output2+0x4af/0xe40 net/ipv4/ip_output.c:228
__ip_finish_output net/ipv4/ip_output.c:308 [inline]
__ip_finish_output+0x23a/0x490 net/ipv4/ip_output.c:290
ip_finish_output+0x41/0x160 net/ipv4/ip_output.c:318
NF_HOOK_COND include/linux/netfilter.h:294 [inline]
ip_output+0xdf/0x210 net/ipv4/ip_output.c:432
dst_output include/net/dst.h:436 [inline]
ip_local_out+0x74/0x90 net/ipv4/ip_output.c:125
__ip_queue_xmit+0x3a8/0xa40 net/ipv4/ip_output.c:532
ip_queue_xmit+0x45/0x60 include/net/ip.h:237
__tcp_transmit_skb+0xe81/0x1d60 net/ipv4/tcp_output.c:1169
tcp_transmit_skb net/ipv4/tcp_output.c:1185 [inline]
__tcp_retransmit_skb+0x4bd/0x15f0 net/ipv4/tcp_output.c:2976
tcp_retransmit_skb+0x36/0x1a0 net/ipv4/tcp_output.c:2999
tcp_retransmit_timer+0x719/0x16d0 net/ipv4/tcp_timer.c:515
tcp_write_timer_handler+0x42d/0x510 net/ipv4/tcp_timer.c:598
tcp_write_timer+0xd1/0xf0 net/ipv4/tcp_timer.c:618

read to 0xffff8880a41dba78 of 8 bytes by interrupt on cpu 0:
neigh_event_send include/net/neighbour.h:442 [inline]
neigh_resolve_output+0x57/0x480 net/core/neighbour.c:1474
neigh_output include/net/neighbour.h:511 [inline]
ip_finish_output2+0x4af/0xe40 net/ipv4/ip_output.c:228
__ip_finish_output net/ipv4/ip_output.c:308 [inline]
__ip_finish_output+0x23a/0x490 net/ipv4/ip_output.c:290
ip_finish_output+0x41/0x160 net/ipv4/ip_output.c:318
NF_HOOK_COND include/linux/netfilter.h:294 [inline]
ip_output+0xdf/0x210 net/ipv4/ip_output.c:432
dst_output include/net/dst.h:436 [inline]
ip_local_out+0x74/0x90 net/ipv4/ip_output.c:125
__ip_queue_xmit+0x3a8/0xa40 net/ipv4/ip_output.c:532
ip_queue_xmit+0x45/0x60 include/net/ip.h:237
__tcp_transmit_skb+0xe81/0x1d60 net/ipv4/tcp_output.c:1169
tcp_transmit_skb net/ipv4/tcp_output.c:1185 [inline]
__tcp_retransmit_skb+0x4bd/0x15f0 net/ipv4/tcp_output.c:2976
tcp_retransmit_skb+0x36/0x1a0 net/ipv4/tcp_output.c:2999
tcp_retransmit_timer+0x719/0x16d0 net/ipv4/tcp_timer.c:515
tcp_write_timer_handler+0x42d/0x510 net/ipv4/tcp_timer.c:598

Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.4.0-rc3+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011

Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch '100GbE' of git://git./linux/kernel/git/jkirsher/next-queue

Jeff Kirsher says:

====================
100GbE Intel Wired LAN Driver Updates 2019-11-08

Another series that contains updates to the ice driver only.

Anirudh cleans up the code of kernel config of ifdef wrappers by moving
code that is needed by DCB to disable and enable the PF VSI for
configuration.  Implements ice_vsi_type_str() to convert an VSI type
enum value to its string equivalent to help identify VSI types from
module print statements.

Usha and Tarun add support for setting the maximum per-queue bit rate
for transmit queues.

Dave implements dcb_nl set functions and supporting software DCB
functions to support the callbacks defined in the dcbnl_rtnl_ops
structure.

Henry adds a check to ensure we are not resetting the device when trying
to configure it, and to return -EBUSY during a reset.

Usha fixes a call trace caused by the receive/transmit descriptor size
change request via ethtool when DCB is configured by using the number of
enabled queues and not the total number of allocated queues.

Paul cleans up and refactors the software LLDP configuration to handle
when firmware DCBX is disabled.

Akeem adds checks to ensure the VF or PF is not disabled before honoring
mailbox messages to configure the VF.

Brett corrects the check to make sure the vector_id passed down from
iavf is less than the max allowed interrupts per VF.  Updates a flag bit
to align with the current specification.

Bruce updates a switch statement to use the correct status of the
Download Package AQ command.  Does some housekeeping by cleaning up a
conditional check that is not needed.

Mitch shortens up the delay for SQ responses to resolve issues with VF
resets failing.

Jake cleans up the code reducing namespace pollution and to simplify
ice_debug_cq() since it always uses the same mask, not need to pass it
in.  Improve debugging by adding the command opcode in the debug
messages that print an error code.

v2: fixed reverse christmas tree issue in patch 3 of the series.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'pwm/for-5.4-rc7' of git://git./linux/kernel/git/thierry.reding/linux-pwm

Pull pwm fix from Thierry Reding:
"One more fix to keep a reference to the driver's module as long as
there are users of the PWM exposed by the driver"

* tag 'pwm/for-5.4-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
pwm: bcm-iproc: Prevent unloading the driver module while in use

cgroup,writeback: don't switch wbs immediately on dead wbs if the memcg is dead

cgroup writeback tries to refresh the associated wb immediately if the
current wb is dead.  This is to avoid keeping issuing IOs on the stale
wb after memcg - blkcg association has changed (ie. when blkcg got
disabled / enabled higher up in the hierarchy).

Unfortunately, the logic gets triggered spuriously on inodes which are
associated with dead cgroups.  When the logic is triggered on dead
cgroups, the attempt fails only after doing quite a bit of work
allocating and initializing a new wb.

While c3aab9a0bd91 ("mm/filemap.c: don't initiate writeback if mapping
has no dirty pages") alleviated the issue significantly as it now only
triggers when the inode has dirty pages.  However, the condition can
still be triggered before the inode is switched to a different cgroup
and the logic simply doesn't make sense.

Skip the immediate switching if the associated memcg is dying.

This is a simplified version of the following two patches:

* https://lore.kernel.org/linux-mm/20190513183053.GA73423@dennisz-mbp/
* http://lkml.kernel.org/r/156355839560.2063.5265687291430814589.stgit@buzz

Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Fixes: e8a7abf5a5bd ("writeback: disassociate inodes from dying bdi_writebacks")
Acked-by: Dennis Zhou <dennis@kernel.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

net: icmp: fix data-race in cmp_global_allow()

This code reads two global variables without protection
of a lock. We need READ_ONCE()/WRITE_ONCE() pairs to
avoid load/store-tearing and better document the intent.

KCSAN reported :
BUG: KCSAN: data-race in icmp_global_allow / icmp_global_allow

read to 0xffffffff861a8014 of 4 bytes by task 11201 on cpu 0:
icmp_global_allow+0x36/0x1b0 net/ipv4/icmp.c:254
icmpv6_global_allow net/ipv6/icmp.c:184 [inline]
icmpv6_global_allow net/ipv6/icmp.c:179 [inline]
icmp6_send+0x493/0x1140 net/ipv6/icmp.c:514
icmpv6_send+0x71/0xb0 net/ipv6/ip6_icmp.c:43
ip6_link_failure+0x43/0x180 net/ipv6/route.c:2640
dst_link_failure include/net/dst.h:419 [inline]
vti_xmit net/ipv4/ip_vti.c:243 [inline]
vti_tunnel_xmit+0x27f/0xa50 net/ipv4/ip_vti.c:279
__netdev_start_xmit include/linux/netdevice.h:4420 [inline]
netdev_start_xmit include/linux/netdevice.h:4434 [inline]
xmit_one net/core/dev.c:3280 [inline]
dev_hard_start_xmit+0xef/0x430 net/core/dev.c:3296
__dev_queue_xmit+0x14c9/0x1b60 net/core/dev.c:3873
dev_queue_xmit+0x21/0x30 net/core/dev.c:3906
neigh_direct_output+0x1f/0x30 net/core/neighbour.c:1530
neigh_output include/net/neighbour.h:511 [inline]
ip6_finish_output2+0x7a6/0xec0 net/ipv6/ip6_output.c:116
__ip6_finish_output net/ipv6/ip6_output.c:142 [inline]
__ip6_finish_output+0x2d7/0x330 net/ipv6/ip6_output.c:127
ip6_finish_output+0x41/0x160 net/ipv6/ip6_output.c:152
NF_HOOK_COND include/linux/netfilter.h:294 [inline]
ip6_output+0xf2/0x280 net/ipv6/ip6_output.c:175
dst_output include/net/dst.h:436 [inline]
ip6_local_out+0x74/0x90 net/ipv6/output_core.c:179

write to 0xffffffff861a8014 of 4 bytes by task 11183 on cpu 1:
icmp_global_allow+0x174/0x1b0 net/ipv4/icmp.c:272
icmpv6_global_allow net/ipv6/icmp.c:184 [inline]
icmpv6_global_allow net/ipv6/icmp.c:179 [inline]
icmp6_send+0x493/0x1140 net/ipv6/icmp.c:514
icmpv6_send+0x71/0xb0 net/ipv6/ip6_icmp.c:43
ip6_link_failure+0x43/0x180 net/ipv6/route.c:2640
dst_link_failure include/net/dst.h:419 [inline]
vti_xmit net/ipv4/ip_vti.c:243 [inline]
vti_tunnel_xmit+0x27f/0xa50 net/ipv4/ip_vti.c:279
__netdev_start_xmit include/linux/netdevice.h:4420 [inline]
netdev_start_xmit include/linux/netdevice.h:4434 [inline]
xmit_one net/core/dev.c:3280 [inline]
dev_hard_start_xmit+0xef/0x430 net/core/dev.c:3296
__dev_queue_xmit+0x14c9/0x1b60 net/core/dev.c:3873
dev_queue_xmit+0x21/0x30 net/core/dev.c:3906
neigh_direct_output+0x1f/0x30 net/core/neighbour.c:1530
neigh_output include/net/neighbour.h:511 [inline]
ip6_finish_output2+0x7a6/0xec0 net/ipv6/ip6_output.c:116
__ip6_finish_output net/ipv6/ip6_output.c:142 [inline]
__ip6_finish_output+0x2d7/0x330 net/ipv6/ip6_output.c:127
ip6_finish_output+0x41/0x160 net/ipv6/ip6_output.c:152
NF_HOOK_COND include/linux/netfilter.h:294 [inline]
ip6_output+0xf2/0x280 net/ipv6/ip6_output.c:175

Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 11183 Comm: syz-executor.2 Not tainted 5.4.0-rc3+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011

Fixes: 4cdf507d5452 ("icmp: add a global rate limitation")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'ceph-for-5.4-rc7' of git://github.com/ceph/ceph-client

Pull ceph fixes from Ilya Dryomov:
"Some late-breaking dentry handling fixes from Al and Jeff, a patch to
  further restrict copy_file_range() to avoid potential data corruption
  from Luis and a fix for !CONFIG_CEPH_FSCACHE kernels.

  Everything but the fscache fix is marked for stable"

* tag 'ceph-for-5.4-rc7' of git://github.com/ceph/ceph-client:
  ceph: return -EINVAL if given fsc mount option on kernel w/o support
  ceph: don't allow copy_file_range when stripe_count != 1
  ceph: don't try to handle hashed dentries in non-O_CREAT atomic_open
  ceph: add missing check in d_revalidate snapdir handling
  ceph: fix RCU case handling in ceph_d_revalidate()
  ceph: fix use-after-free in __ceph_remove_cap()

net/sched: annotate lockless accesses to qdisc->empty

KCSAN reported the following race [1]

BUG: KCSAN: data-race in __dev_queue_xmit / net_tx_action

read to 0xffff8880ba403508 of 1 bytes by task 21814 on cpu 1:
__dev_xmit_skb net/core/dev.c:3389 [inline]
__dev_queue_xmit+0x9db/0x1b40 net/core/dev.c:3761
dev_queue_xmit+0x21/0x30 net/core/dev.c:3825
neigh_hh_output include/net/neighbour.h:500 [inline]
neigh_output include/net/neighbour.h:509 [inline]
ip6_finish_output2+0x873/0xec0 net/ipv6/ip6_output.c:116
__ip6_finish_output net/ipv6/ip6_output.c:142 [inline]
__ip6_finish_output+0x2d7/0x330 net/ipv6/ip6_output.c:127
ip6_finish_output+0x41/0x160 net/ipv6/ip6_output.c:152
NF_HOOK_COND include/linux/netfilter.h:294 [inline]
ip6_output+0xf2/0x280 net/ipv6/ip6_output.c:175
dst_output include/net/dst.h:436 [inline]
ip6_local_out+0x74/0x90 net/ipv6/output_core.c:179
ip6_send_skb+0x53/0x110 net/ipv6/ip6_output.c:1795
udp_v6_send_skb.isra.0+0x3ec/0xa70 net/ipv6/udp.c:1173
udpv6_sendmsg+0x1906/0x1c20 net/ipv6/udp.c:1471
inet6_sendmsg+0x6d/0x90 net/ipv6/af_inet6.c:576
sock_sendmsg_nosec net/socket.c:637 [inline]
sock_sendmsg+0x9f/0xc0 net/socket.c:657
___sys_sendmsg+0x2b7/0x5d0 net/socket.c:2311
__sys_sendmmsg+0x123/0x350 net/socket.c:2413
__do_sys_sendmmsg net/socket.c:2442 [inline]
__se_sys_sendmmsg net/socket.c:2439 [inline]
__x64_sys_sendmmsg+0x64/0x80 net/socket.c:2439
do_syscall_64+0xcc/0x370 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x44/0xa9

write to 0xffff8880ba403508 of 1 bytes by interrupt on cpu 0:
qdisc_run_begin include/net/sch_generic.h:160 [inline]
qdisc_run include/net/pkt_sched.h:120 [inline]
net_tx_action+0x2b1/0x6c0 net/core/dev.c:4551
__do_softirq+0x115/0x33f kernel/softirq.c:292
do_softirq_own_stack+0x2a/0x40 arch/x86/entry/entry_64.S:1082
do_softirq.part.0+0x6b/0x80 kernel/softirq.c:337
do_softirq kernel/softirq.c:329 [inline]
__local_bh_enable_ip+0x76/0x80 kernel/softirq.c:189
local_bh_enable include/linux/bottom_half.h:32 [inline]
rcu_read_unlock_bh include/linux/rcupdate.h:688 [inline]
ip6_finish_output2+0x7bb/0xec0 net/ipv6/ip6_output.c:117
__ip6_finish_output net/ipv6/ip6_output.c:142 [inline]
__ip6_finish_output+0x2d7/0x330 net/ipv6/ip6_output.c:127
ip6_finish_output+0x41/0x160 net/ipv6/ip6_output.c:152
NF_HOOK_COND include/linux/netfilter.h:294 [inline]
ip6_output+0xf2/0x280 net/ipv6/ip6_output.c:175
dst_output include/net/dst.h:436 [inline]
ip6_local_out+0x74/0x90 net/ipv6/output_core.c:179
ip6_send_skb+0x53/0x110 net/ipv6/ip6_output.c:1795
udp_v6_send_skb.isra.0+0x3ec/0xa70 net/ipv6/udp.c:1173
udpv6_sendmsg+0x1906/0x1c20 net/ipv6/udp.c:1471
inet6_sendmsg+0x6d/0x90 net/ipv6/af_inet6.c:576
sock_sendmsg_nosec net/socket.c:637 [inline]
sock_sendmsg+0x9f/0xc0 net/socket.c:657
___sys_sendmsg+0x2b7/0x5d0 net/socket.c:2311
__sys_sendmmsg+0x123/0x350 net/socket.c:2413
__do_sys_sendmmsg net/socket.c:2442 [inline]
__se_sys_sendmmsg net/socket.c:2439 [inline]
__x64_sys_sendmmsg+0x64/0x80 net/socket.c:2439
do_syscall_64+0xcc/0x370 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x44/0xa9

Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 21817 Comm: syz-executor.2 Not tainted 5.4.0-rc6+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011

Fixes: d518d2ed8640 ("net/sched: fix race between deactivation and dequeue for NOLOCK qdisc")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

vsock/virtio: fix sock refcnt holding during the shutdown

The "42f5cda5eaf4" commit rightly set SOCK_DONE on peer shutdown,
but there is an issue if we receive the SHUTDOWN(RDWR) while the
virtio_transport_close_timeout() is scheduled.
In this case, when the timeout fires, the SOCK_DONE is already
set and the virtio_transport_close_timeout() will not call
virtio_transport_reset() and virtio_transport_do_close().
This causes that both sockets remain open and will never be released,
preventing the unloading of [virtio|vhost]_transport modules.

This patch fixes this issue, calling virtio_transport_reset() and
virtio_transport_do_close() when we receive the SHUTDOWN(RDWR)
and there is nothing left to read.

Fixes: 42f5cda5eaf4 ("vsock/virtio: set SOCK_DONE on peer shutdown")
Cc: Stephen Barber <smbarber@chromium.org>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ice: print opcode when printing controlq errors

To help aid in debugging, display the command opcode in debug messages
that print an error code. This makes it easier to see what command
failed if only ICE_DBG_AQ_MSG is enabled.

Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>