Rafał Miłecki [Wed, 20 Jan 2021 20:13:08 +0000 (21:13 +0100)]
bcm4908: use backported brcmstb soc stubs patch
Final version differs slightly - uses IS_ENABLED()
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rafał Miłecki [Wed, 20 Jan 2021 19:20:24 +0000 (20:20 +0100)]
bcm4908: use backported switch & PMB DTS patches
Final versions differ slightly from what was used initially.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rafał Miłecki [Wed, 20 Jan 2021 06:39:25 +0000 (07:39 +0100)]
bcm4908: add pending mtd patches for BCM4908 partitioning
BCM4908 can have multiple firmware partitions. MTD needs to detect which
one is currently used.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rafał Miłecki [Tue, 19 Jan 2021 20:36:30 +0000 (21:36 +0100)]
kernel: backport mtd commit converting partitions doc syntax
1. It's useful for developing & validating DTS files inside OpenWrt
2. This will allow backporting later changes that depend on it
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
John Audia [Tue, 19 Jan 2021 21:13:26 +0000 (16:13 -0500)]
kernel: bump 5.4 to 5.4.91
All modification made by update_kernel.sh in a fresh clone without
existing toolchains.
Build system: x86_64
Build-tested: ipq806x/R7800, bcm27xx/bcm2711
Run-tested: ipq806x/R7800
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
Tested-by: Curtis Deptuck <curtdept@me.com> [x86/64]
Sven Eckelmann [Mon, 23 Nov 2020 12:41:34 +0000 (13:41 +0100)]
ath79: Add support for OpenMesh MR1750 v2
Device specifications:
======================
* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/240 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 3T3R 2.4 GHz Wi-Fi (11n)
* 3T3R 5 GHz Wi-Fi (11ac)
* 6x GPIO-LEDs (2x wifi, 2x status, 1x lan, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 1x ethernet
- AR8035 ethernet PHY (RGMII)
- 10/100/1000 Mbps Ethernet
- 802.3af POE
- used as LAN interface
* 12-24V 1A DC
* internal antennas
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot
0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to the
device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
[rebase, add LED migration]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Sven Eckelmann [Mon, 23 Nov 2020 12:41:34 +0000 (13:41 +0100)]
ath79: Add support for OpenMesh MR1750 v1
Device specifications:
======================
* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/240 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 3T3R 2.4 GHz Wi-Fi (11n)
* 3T3R 5 GHz Wi-Fi (11ac)
* 6x GPIO-LEDs (2x wifi, 2x status, 1x lan, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 1x ethernet
- AR8035 ethernet PHY (RGMII)
- 10/100/1000 Mbps Ethernet
- 802.3af POE
- used as LAN interface
* 12-24V 1A DC
* internal antennas
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot
0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to the
device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
[rebase, apply shared DTSI/device node, add LED migration]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Tue, 19 Jan 2021 13:53:36 +0000 (14:53 +0100)]
ath79: make OpenMesh MR900 DTSI more general
The OpenMesh MR900 and to-be-added MR1750 family are very similar.
Make the existing MR900 DTSI more general so it can be used for
the MR1750 devices as well.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Tue, 19 Jan 2021 13:28:05 +0000 (14:28 +0100)]
ath79: consolidate common definitions for OpenMesh devices
The shared image definitions for OpenMesh devices are currently
organized based on device families. This introduces some duplicate
code, as the image creation code is mostly the same for those.
This patch thus derives two basic shared definitions that work for
all devices and only requires a few variables to be moved back to
the device definitions.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Sven Eckelmann [Wed, 30 Dec 2020 20:56:55 +0000 (21:56 +0100)]
ath79: apply Engenius
ECB1750 style to OpenMesh MR900 RGMII cfg
The OpenMesh MR900 is a modified version of the Exx900/Exx1750 family.
These devices are shipped with an AR803x PHY and had various problems with
the delay configuration in ar71xx. These problems are now in the past [1]
and parts of the delay configuration should now be done in the PHY only.
Just switch to the configuration of the
ECB1750 to have an already well
tested configuration for ath79 with the newer kernel versions.
[1] https://github.com/openwrt/openwrt/pull/3505#issuecomment-
716050292
Reported-by: Michael Pratt <mcpratt@pm.me>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Sven Eckelmann [Mon, 23 Nov 2020 12:41:34 +0000 (13:41 +0100)]
ath79: Add support for OpenMesh MR900 v2
Device specifications:
======================
* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/240 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 3T3R 2.4 GHz Wi-Fi
* 3T3R 5 GHz Wi-Fi
* 6x GPIO-LEDs (2x wifi, 2x status, 1x lan, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 1x ethernet
- AR8035 ethernet PHY (RGMII)
- 10/100/1000 Mbps Ethernet
- 802.3af POE
- used as LAN interface
* 12-24V 1A DC
* internal antennas
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot
0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to the
device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
[rebase, add LED migration]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Sven Eckelmann [Mon, 23 Nov 2020 12:41:34 +0000 (13:41 +0100)]
ath79: Add support for OpenMesh MR900 v1
Device specifications:
======================
* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/240 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 3T3R 2.4 GHz Wi-Fi
* 3T3R 5 GHz Wi-Fi
* 6x GPIO-LEDs (2x wifi, 2x status, 1x lan, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 1x ethernet
- AR8035 ethernet PHY (RGMII)
- 10/100/1000 Mbps Ethernet
- 802.3af POE
- used as LAN interface
* 12-24V 1A DC
* internal antennas
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot
0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to the
device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
[rebase, add LED migration]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Sven Eckelmann [Wed, 30 Dec 2020 20:56:55 +0000 (21:56 +0100)]
ath79: apply Engenius EAP600 style to OpenMesh MR600 RGMII cfg
The OpenMesh MR600 is a modified version of the EAP600 family. These
devices are shipped with an AR803x PHY and had various problems with the
delay configuration in ar71xx. These problems are now in the past [1] and
parts of the delay configuration should now be done in the PHY only.
Just switch to the configuration of the EAP600 to have an already well
tested configuration for ath79 with the newer kernel versions.
[1] https://github.com/openwrt/openwrt/pull/3505#issuecomment-
716050292
Reported-by: Michael Pratt <mcpratt@pm.me>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Sven Eckelmann [Mon, 23 Nov 2020 12:41:34 +0000 (13:41 +0100)]
ath79: Add support for OpenMesh MR600 v2
Device specifications:
======================
* Qualcomm/Atheros AR9344 rev 2
* 560/450/225 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2T2R 2.4 GHz Wi-Fi
* 2T2R 5 GHz Wi-Fi
* 8x GPIO-LEDs (6x wifi, 1x wps, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 1x ethernet
- AR8035 ethernet PHY (RGMII)
- 10/100/1000 Mbps Ethernet
- 802.3af POE
- used as LAN interface
* 12-24V 1A DC
* internal antennas
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot
0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to the
device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
[rebase, add LED migration]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Sven Eckelmann [Mon, 23 Nov 2020 12:41:34 +0000 (13:41 +0100)]
ath79: Add support for OpenMesh MR600 v1
Device specifications:
======================
* Qualcomm/Atheros AR9344 rev 2
* 560/450/225 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2T2R 2.4 GHz Wi-Fi
* 2T2R 5 GHz Wi-Fi
* 4x GPIO-LEDs (2x wifi, 1x wps, 1x power)
* 1x GPIO-button (reset)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 1x ethernet
- AR8035 ethernet PHY (RGMII)
- 10/100/1000 Mbps Ethernet
- 802.3af POE
- used as LAN interface
* 12-24V 1A DC
* internal antennas
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot
0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to the
device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
[rebase, make WLAN LEDs consistent, add LED migration]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Nick Hainke [Sat, 16 Jan 2021 12:48:50 +0000 (13:48 +0100)]
owipcalc: remove clone in cidr_contains6
The "cidr_contains6" functions clones the given cidr. The contains4
does not clone the cidr. Both functions do not behave the same.
I see no reason to push the cidr. I think that we get only a negligible
performance gain, but it makes ipv4 and ipv6 equal again.
Signed-off-by: Nick Hainke <vincent@systemli.org>
John Audia [Sun, 17 Jan 2021 14:15:14 +0000 (09:15 -0500)]
kernel: bump 5.4 to 5.4.90
All modification made by update_kernel.sh in a fresh clone without
existing toolchains.
Build system: x86_64
Build-tested: ipq806x/R7800, bcm27xx/bcm2711
Run-tested: ipq806x/R7800
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
Tested-by: Curtis Deptuck <curtdept@me.com> [x86/64]
Hauke Mehrtens [Sun, 10 Jan 2021 23:33:07 +0000 (00:33 +0100)]
dnsmasq: Update to version 2.83
This fixes the following security problems in dnsmasq:
* CVE-2020-25681:
Dnsmasq versions before 2.83 is susceptible to a heap-based buffer
overflow in sort_rrset() when DNSSEC is used. This can allow a remote
attacker to write arbitrary data into target device's memory that can
lead to memory corruption and other unexpected behaviors on the target
device.
* CVE-2020-25682:
Dnsmasq versions before 2.83 is susceptible to buffer overflow in
extract_name() function due to missing length check, when DNSSEC is
enabled. This can allow a remote attacker to cause memory corruption
on the target device.
* CVE-2020-25683:
Dnsmasq version before 2.83 is susceptible to a heap-based buffer
overflow when DNSSEC is enabled. A remote attacker, who can create
valid DNS replies, could use this flaw to cause an overflow in a heap-
allocated memory. This flaw is caused by the lack of length checks in
rtc1035.c:extract_name(), which could be abused to make the code
execute memcpy() with a negative size in get_rdata() and cause a crash
in Dnsmasq, resulting in a Denial of Service.
* CVE-2020-25684:
A lack of proper address/port check implemented in Dnsmasq version <
2.83 reply_query function makes forging replies easier to an off-path
attacker.
* CVE-2020-25685:
A lack of query resource name (RRNAME) checks implemented in Dnsmasq's
versions before 2.83 reply_query function allows remote attackers to
spoof DNS traffic that can lead to DNS cache poisoning.
* CVE-2020-25686:
Multiple DNS query requests for the same resource name (RRNAME) by
Dnsmasq versions before 2.83 allows for remote attackers to spoof DNS
traffic, using a birthday attack (RFC 5452), that can lead to DNS
cache poisoning.
* CVE-2020-25687:
Dnsmasq versions before 2.83 is vulnerable to a heap-based buffer
overflow with large memcpy in sort_rrset() when DNSSEC is enabled. A
remote attacker, who can create valid DNS replies, could use this flaw
to cause an overflow in a heap-allocated memory. This flaw is caused
by the lack of length checks in rtc1035.c:extract_name(), which could
be abused to make the code execute memcpy() with a negative size in
sort_rrset() and cause a crash in dnsmasq, resulting in a Denial of
Service.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Mon, 18 Jan 2021 20:57:10 +0000 (21:57 +0100)]
uboot-at91: Add PKG_MIRROR_HASH to fix download
The referenced commit is gone, but we already have this file on our
mirror, use that one by providing the correct mirror hash.
I generated a tar.xz file with the given git commit hash using a random
fork on github and it generated the same tar.xz file as found on our
mirror so this looks correct.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Mon, 18 Jan 2021 20:57:05 +0000 (21:57 +0100)]
at91bootstrap: Add PKG_MIRROR_HASH to fix download
The referenced commit is gone, but we already have this file on our
mirror, use that one by providing the correct mirror hash.
I generated a tar.xz file with the given git commit hash using a random
fork on github and it generated the same tar.xz file as found on our
mirror so this looks correct.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Paul Spooren [Mon, 18 Jan 2021 19:07:22 +0000 (09:07 -1000)]
include: update logo with better kerning
Kerning seems to be very off-putting for some people so the logo
designer thankfully updated guidelines to something which is now
considered final.
Signed-off-by: Paul Spooren <mail@aparcar.org>
David Bauer [Sat, 16 Jan 2021 19:08:35 +0000 (20:08 +0100)]
ath79: rename UniFi AC kernel1 partition
These devices do not run Ubiquiti AirOS. Rename the partition to the
name used by other UniFi devices with vendor dualboot support.
Signed-off-by: David Bauer <mail@david-bauer.net>
David Bauer [Fri, 15 Jan 2021 01:15:12 +0000 (02:15 +0100)]
rockchip: use stable MAC-address for NanoPi R2S
The NanoPi R2S does not have a board specific MAC address written inside
e.g. an EEPROM, hence why it is randomly generated on first boot.
The issue with that however is the lack of a driver for the PRNG.
It often results to the same MAC address used on multiple boards by
default, as urngd is not active at this early stage resulting in low
available entropy.
There is however a semi-unique identifier available to us, which is the
CID of the used SD card. It is unique to each SD card, hence we can use
it to generate the MAC address used for LAN and WAN.
Signed-off-by: David Bauer <mail@david-bauer.net>
Rafał Miłecki [Fri, 15 Jan 2021 09:44:12 +0000 (10:44 +0100)]
bcm63xx-cfe: enable package for bcm4908
bcm4908 target needs to include cferam images in firmware files too
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rafał Miłecki [Wed, 13 Jan 2021 13:14:11 +0000 (14:14 +0100)]
firmware-utils: bcm4908img: tool adding BCM4908 image tail
Flashing image with BCM4908 CFE bootloader requires specific firmware
format. It needs 20 extra bytes with magic numbers and CRC32 appended.
This tools allows appending such a tail to the specified image and also
verifying CRC32 of existing BCM4908 image.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rosen Penev [Mon, 4 Jan 2021 00:28:43 +0000 (16:28 -0800)]
mbedtls: update to 2.16.9
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Hans Dedecker [Wed, 13 Jan 2021 19:14:47 +0000 (20:14 +0100)]
netifd: fix IPv6 routing loop on point-to-point links
c00c833 interface-ip: add unreachable route if address is offlink
e71909c interface-ip: coding style fixes
Tested-by: Karl Vogel <karl.vogel@gmail.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Hans Dedecker [Wed, 13 Jan 2021 19:06:23 +0000 (20:06 +0100)]
odhcp6c: fix routing loop on point-to-point links
53f07e9 ra: fix routing loop on point to point links
2b6959d ra: align ifindex resolving
Tested-by: Karl Vogel <karl.vogel@gmail.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Robert Marko [Fri, 30 Oct 2020 17:42:37 +0000 (18:42 +0100)]
ipq40xx: mikrotik: enable MikroTik platform driver
This enables the MikroTik platform driver, it enables us to parse
valuable info from hard_config including WLAN calibration data
extraction from sysfs.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Robert Marko [Fri, 30 Oct 2020 17:40:27 +0000 (18:40 +0100)]
ipq40xx: mikrotik: enable MikroTik NOR parser
Needed for SPI-NOR based MikroTik IPQ40xx devices like hAP ac2.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Robert Marko [Fri, 30 Oct 2020 17:39:04 +0000 (18:39 +0100)]
ipq40xx: mikrotik: enable CONFIG_MTD_ROUTERBOOT_PARTS
This enables the new MikroTik specific partition parser.
This avoids manually specifying the MikroTik specific partitions as they
can be detected by their magic values.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Robert Marko [Thu, 12 Nov 2020 17:13:26 +0000 (18:13 +0100)]
ipq40xx: add MikroTik subtarget
MikroTik devices require the use of raw vmlinux out of the self
extracting compressed kernels.
They also require 4K sectors, kernel2minor, partition parser as well as
RouterBoard platform drivers.
So in order to not add unnecessary code to the generic sub target lets
introduce a MikroTik sub target.
Signed-off-by: Robert Marko <robimarko@gmail.com>
John Thomson [Fri, 23 Oct 2020 09:49:26 +0000 (19:49 +1000)]
ipq40xx: kernel compressed boot: reset watchdog countdown
If the watchdog is enabled, set the timeout to 30 seconds before
decompress is started.
Mikrotik ipq40xx devices running with RouterBoot have the SoC watchdog
enabled and running with a timeout that does not allow time for the
kernel to decompress and manage the watchdog.
On ipq40xx RouterBoot TFTP boot the watchdog countdown is reset before:
Jumping to kernel
Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
Robert Marko [Fri, 30 Oct 2020 12:58:29 +0000 (13:58 +0100)]
ipq40xx: arm: compressed: add appended DTB section
This adds a appended_dtb section to the ARM decompressor
linker script.
This allows using the existing ARM zImage appended DTB support for
appending a DTB to the raw ELF kernel.
Its size is set to 1MB max to match the zImage appended DTB size limit.
To use it to pass the DTB to the kernel, objcopy is used:
objcopy --set-section-flags=.appended_dtb=alloc,contents \
--update-section=.appended_dtb=<target>.dtb vmlinux
This is based off the following patch:
https://github.com/openwrt/openwrt/commit/
c063e27e02a9dcac0e7f5877fb154e58fa3e1a69
Signed-off-by: Robert Marko <robimarko@gmail.com>
Rosen Penev [Mon, 4 Jan 2021 00:27:10 +0000 (16:27 -0800)]
libusb: make InstallDev explicit
Helps to see what actually gets installed.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Rosen Penev [Mon, 4 Jan 2021 00:27:09 +0000 (16:27 -0800)]
libusb: cleanup PKG_ variables
Reordered for consistency between packages.
Fixed license information.
Change PKG_BUILD_PARALLEL to 1. This is no longer a problem.1
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Rosen Penev [Mon, 4 Jan 2021 00:27:08 +0000 (16:27 -0800)]
libusb: update to 1.0.24
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Alexander Couzens [Sun, 17 Jan 2021 05:54:04 +0000 (06:54 +0100)]
ipq40xx: split generic images into own file
In preparation of the new mikrotik subtarget split the generic images
into generic.mk
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Hans Dedecker [Fri, 15 Jan 2021 19:45:38 +0000 (20:45 +0100)]
glibc: update to latest 2.32 commit (BZ #20019, BZ #27177, BZ #27130)
4c619b3eed x86: Check IFUNC definition in unrelocated executable [BZ #20019]
87450ecf8a x86: Set header.feature_1 in TCB for always-on CET [BZ #27177]
2b4f67c2b3 Update for [BZ #27130] fix
1a24bbd43e x86-64: Avoid rep movsb with short distance [BZ #27130]
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Rui Salvaterra [Wed, 2 Dec 2020 15:42:07 +0000 (15:42 +0000)]
ramips: mt7621: refresh the kernel config
The removed config symbols are already enabled by the generic kernel
configuration (or by default), while the added ones are forcefully
enabled by the specific architecture.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Adrian Schmutzler [Sat, 2 Jan 2021 14:09:09 +0000 (15:09 +0100)]
ath79: remove USB port definition for TP-Link TL-WR810N v1
The USB port definition is only needed when it is linked to a USB
LED. Since there is none for this device, we might as well remove
the port definition.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Russell Senior [Wed, 23 Dec 2020 02:32:54 +0000 (18:32 -0800)]
ath79: Add support for Ubiquiti Bullet AC
CPU: Atheros AR9342 rev 3 SoC
RAM: 64 MB DDR2
Flash: 16 MB NOR SPI
WLAN 2.4GHz: Atheros AR9342 v3 (ath9k)
WLAN 5.0GHz: QCA988X
Ports: 1x GbE
Flashing procedure is identical to other ubnt devices.
https://openwrt.org/toh/ubiquiti/common
Flashing through factory firmware
1. Ensure firmware version v8.7.0 is installed.
Up/downgrade to this exact version.
2. Patch fwupdate.real binary using
`hexdump -Cv /bin/ubntbox | sed 's/14 40 fe 27/00 00 00 00/g' | \
hexdump -R > /tmp/fwupdate.real`
3. Make the patched fwupdate.real binary executable using
`chmod +x /tmp/fwupdate.real`
4. Copy the squashfs factory image to /tmp on the device
5. Flash OpenWrt using `/tmp/fwupdate.real -m <squashfs-factory image>`
6. Wait for the device to reboot
(copied from Ubiquiti NanoBeam AC and modified)
Flashing from serial console
1. Connect serial console (115200 baud)
2. Connect ethernet to a network with a TFTP server, through a
passive PoE injector.
3. Press a key to obtain a u-boot prompt
4. Set your TFTP server's ip address, with:
setenv serverip <tftp-server-address>
5. Set the Bullet AC's ip address, with:
setenv ipaddr <bullet-ac-address>
6. Set the boot file, with:
setenv bootfile <name-of-initramfs-binary-on-tftp-server>
7. Fetch the binary with tftp:
tftpboot
8. Boot the initramfs binary:
bootm
9. From the initramfs, fetch the sysupgrade binary, and flash it with
sysupgrade.
The Bullet AC is identified as a 2WA board by Ubiquiti. As such, the UBNT_TYPE
must match from the "Flashing through factory firmware" install instructions
to work.
Phy0 is QCA988X which can tune either band (2.4 or 5GHz). Phy1 is AR9342,
on which 5GHz is disabled. It isn't currently known whether phy1 is
routed to the N connector at all.
Signed-off-by: Russell Senior <russell@personaltelco.net>
Sungbo Eo [Mon, 4 Jan 2021 13:52:20 +0000 (22:52 +0900)]
kernel: drop empty kmod-ledtrig-* packages
The following four led triggers are enabled in generic config.
* kmod-ledtrig-default-on
* kmod-ledtrig-heartbeat
* kmod-ledtrig-netdev
* kmod-ledtrig-timer
Drop the packages and remove them from DEVICE_PACKAGES.
There's no other package depending on them in this repo.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Sungbo Eo [Mon, 4 Jan 2021 13:33:34 +0000 (22:33 +0900)]
treewide: do not disable LED triggers in target config
Those targets have already enabled some other LED triggers, so enabling
a few more won't be a big problem.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Sungbo Eo [Mon, 4 Jan 2021 13:27:28 +0000 (22:27 +0900)]
kernel: enable CONFIG_LEDS_TRIGGER_HEARTBEAT
The heartbeat trigger is used by luci-mod-system, which is installed
as a part of the standard luci package set. It seems the LED trigger
will be required quite often, so let's enable it by default.
This increases uncompressed kernel size by about 100 bytes on ath79/generic.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Leon M. George [Tue, 12 Jan 2021 09:30:08 +0000 (10:30 +0100)]
hostapd: fix setting wps_state to "not configured"
With encryption disabled, it was intended to set wpa_state=1 (enabled,
not configured) through the 'wps_not_configured' flag.
The flag is set appropriately but the condition using it is broken.
Instead, 'wps_configured' is checked and wpa_state is always 2 (enabled,
configured). Fix it by using the correct variable name.
Fixes: 498d84fc4e00 ("netifd: add wireless configuration support
and port mac80211 to the new framework")
Signed-off-by: Leon M. George <leon@georgemail.eu>
[commit title/message improvements]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Sungbo Eo [Sun, 3 Jan 2021 13:40:01 +0000 (22:40 +0900)]
kernel: update kmod-thermal package
CONFIG_THERMAL option was changed to boolean in upstream linux commit
554b3529fe01 ("thermal/drivers/core: Remove the module Kconfig's option").
Switch it to 'y' and remove FILES and AUTOLOAD for non-existant module file.
And update the descripton text for the package as in upstream linux commit
eb8504620381 ("thermal: Rephrase the Kconfig text for thermal").
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Nick Hainke [Wed, 13 Jan 2021 15:06:03 +0000 (16:06 +0100)]
owipcalc: use v6 in cidr_parse6 function
The cidr_parse6 function parses a string to an ipv6-address.
The cidr struct contains a union called buf for the ipv4 and ipv6
address. Since it is a char pointer and the struct is initialized with
the maximum size (so ipv6 string) it does not make any difference.
However, we should access the buffer using the v6 name, since it could
be confusing otherwise.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Jan Alexander [Thu, 14 Jan 2021 13:55:22 +0000 (14:55 +0100)]
ipq806x: fix Ubiquiti UniFi AC HD partition map
This fixes a typo in the previously committed partition map that led to
the extension of the read-only mtd partition "SSD" into the following
partitions.
Fixes: 4e46beb31342 ("ipq806x: add support for Ubiquiti UniFi AC HD")
Signed-off-by: Jan Alexander <jan@nalx.net>
John Audia [Sat, 9 Jan 2021 14:10:40 +0000 (09:10 -0500)]
kernel: bump 5.4 to 5.4.89
All modification made by update_kernel.sh in a fresh clone without
existing toolchains.
Build system: x86_64
Build-tested: ipq806x/R7800, bcm27xx/bcm2711
Run-tested: ipq806x/R7800
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
Tested-by: Curtis Deptuck <curtdept@me.com> [x86/64]
Felix Fietkau [Fri, 15 Jan 2021 12:05:25 +0000 (13:05 +0100)]
mac80211: fix rounding error in minstrel_ht throughput calculation
Fixes rate selection with lower data rates
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Paul Spooren [Wed, 15 Apr 2020 00:49:54 +0000 (14:49 -1000)]
scripts: target-metadata don't add PROFILES twice
Since
4ee3cf2b5a profiles with alternative vendor names may appear
multiple times in `tmp/.targetinfo` or `.targetinfo` (for
ImageBuilders).
The `target-metadata.pl` script adds these profiles then twice to
`PROFILE_NAMES` and the ImageBuilder show the profile twice when running
`make info`.
This patch removes duplicate profile IDs and only adds them once to
`.profiles.mk`.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Rui Salvaterra [Thu, 14 Jan 2021 15:24:58 +0000 (15:24 +0000)]
kernel: make lwtunnel support optional
Not everyone will want to bloat their kernel by 24 kiB for such a niche
feature.
Fixes: a1a7f3274e0ed27511d45f62ee20281d8d57c7af "kernel: enable SRv6 support by
enabling lwtunnel"
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Rafał Miłecki [Wed, 13 Jan 2021 08:16:46 +0000 (09:16 +0100)]
bcm4908: prepend kernel images with a custom header
It's required for CFE to accept kernel.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rafał Miłecki [Wed, 13 Jan 2021 07:11:00 +0000 (08:11 +0100)]
firmware-utils: bcm4908kernel: tool adding BCM4908 kernel header
BCM4908 CFE bootloader requires kernel to be prepended with a custom
header. This simple tool implements support for such headers.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rosen Penev [Fri, 25 Dec 2020 00:36:16 +0000 (16:36 -0800)]
glibc: add arc700 patch
glibc does not officially support ARC700 so this adds the missing
pieces. I looked at uClibc-ng and a patch by Synopsis for glibc.
ran make toolchain/glibc/refresh to clean up fuzz.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Felix Fietkau [Thu, 14 Jan 2021 19:12:08 +0000 (20:12 +0100)]
mac80211: fix an uninitialized stack variable in the minstrel update
It can lead to out-of-bounds access and invalid rates
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Thu, 14 Jan 2021 13:05:58 +0000 (14:05 +0100)]
mt76: update to the latest version
a46f9a9160e9 mt76: mt7915: add vif check in mt7915_update_vif_beacon()
27ad12352ac9 mt76: mt7615: add vif check in mt7615_update_vif_beacon()
0a449cef024e mt76: mt7915: fix MT_CIPHER_BIP_CMAC_128 setkey
eacd2d493c61 mt76: mt7915: reset token when mac_reset happens
e4b23301e6c9 mt76: mt7615: reset token when mac_reset happens
6e22bbfe0360 mt76: mt7615: convert comma to semicolon
37865118ae2d mt76: mt7915: convert comma to semicolon
742c36b2e527 mt76: mt7915: run mt7915_configure_filter holding mt76 mutex
a515727e8423 mt76: mt7915: add support for flash mode
b6f7b3da5216 mt76: mt7915: fix endianness warning in mt7915_mcu_set_radar_th
062f3f4f06a2 mt76: mt7915: simplify mt7915_mcu_send_message routine
dbba9b993300 mt76: mt7915: drop zero-length packet to avoid Tx hang
36a745d0f71c mt76: Fix queue ID variable types after mcu queue split
a4539760b0b1 mt7915: update the testmode support to the latest upstream patch
64bd6f87e4c2 mt7915: fix crash on failure in pci_set_dma_mask
c202ace409e0 mt76: remove unused variable q
d1b827781f84 mt76: mt7915: add partial add_bss_info command on testmode init
a897a69769f5 mt76: testmode: introduce dbdc support
b44472e99822 mt76: testmode: move mtd part to mt76_dev
45e27e6cdc12 mt76: mt7915: move testmode data from dev to phy
b6673b005770 mt76: mt7615: move testmode data from dev to phy
abdd471e9f2d mt76: mt7915: fix ht mcs in mt7915_mcu_get_rx_rate()
d679b56b9585 mt76: move mac_work in mt76_core module
36cd48ab4454 mt76: move chainmask in mt76_phy
89a6781ed045 mt76: mt7915: force ldpc for bw larger than 20MHz in testmode
3d0834e78005 mt76: testmode: add support to set user-defined spe index
cc05f4679667 mt76: testmode: add attributes for ipg related parameters
77b18b16fe16 mt76: testmode: make tx queued limit adjustable
6365a58573cb mt76: mt7915: split edca update function
e56282bf67f6 mt76: mt7915: add support for ipg in testmode
6fa642903e4e mt76: mt7915: calculate new packet length when tx_time is set in testmode
729ec5daeba5 mt76: mt7915: clean hw queue before starting new testmode tx
981443da5cf7 mt76: testmode: add a new state for continuous tx
4793fc9b3d48 mt76: mt7915: rework set state part in testmode
11a1e86e5946 mt76: mt7915: add support for continuous tx in testmode
364affef82fc mt76: mt7615: mt7915: disable txpower sku when testmode enabled
9fc19db51293 mt76: mt7915: simplify peer's TxBF capability check
6377b7f330be mt76: mt7915: add implicit Tx beamforming support
983091a40633 mt76: mt7915: fix MESH ifdef block
bbb7a9e77751 mt76: mt76u: fix NULL pointer dereference in mt76u_status_worker
a28a8dd2f7de mt76: usb: fix crash on device removal
9c312f2ce2c5 mt76: mt7915: rework mcu API
e6fe82acb111 mt76: mt7915: disable RED support in the WA firmware
25d7429bdc41 mt76: mt7915: fix eeprom parsing for DBDC
7a93026dd3dc mt76: mt7915: fix eeprom DBDC band selection
4c8a09cc45d0 tools: Set mode for new file /tmp/mt76-test-%s
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Mon, 11 Jan 2021 17:03:29 +0000 (18:03 +0100)]
tools/fakeroot: fix build regression on macOS
AT_EMPTY_PATH and AT_NO_AUTOMOUNT does not exist there
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Rafał Miłecki [Thu, 14 Jan 2021 11:13:49 +0000 (12:13 +0100)]
bcm4908: backport brcmstb USB PHY driver changes
This includes BCM4908 support
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Leon M. George [Tue, 12 Jan 2021 08:38:02 +0000 (09:38 +0100)]
hostapd: fix key_mgmt typo
The key_mgmt variable was mistyped when checking against "WPS", so
the if clause was never entered.
Fixes: f5753aae233f ("hostapd: add support for WPS pushbutton station")
Signed-off-by: Leon M. George <leon@georgemail.eu>
[add commit message, bump PKG_RELEASE]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Leon M. George [Tue, 12 Jan 2021 09:32:06 +0000 (10:32 +0100)]
hostapd: remove trailing whitespaces
Signed-off-by: Leon M. George <leon@georgemail.eu>
Leon M. George [Tue, 12 Jan 2021 09:07:44 +0000 (10:07 +0100)]
hostapd: remove unused variable
'base' was never used.
Fixes: 498d84fc4e00 ("netifd: add wireless configuration support
and port mac80211 to the new framework")
Signed-off-by: Leon M. George <leon@georgemail.eu>
Leon M. George [Tue, 12 Jan 2021 08:47:47 +0000 (09:47 +0100)]
hostapd: remove unused variable
'enc_str' was never used.
Fixes: 498d84fc4e00 ("netifd: add wireless configuration support
and port mac80211 to the new framework")
Signed-off-by: Leon M. George <leon@georgemail.eu>
Daniel Golle [Sun, 10 Jan 2021 19:12:05 +0000 (19:12 +0000)]
hostapd: run as user 'network' if procd-ujail is installed
Granting capabilities CAP_NET_ADMIN and CAP_NET_RAW allows running
hostapd and wpa_supplicant without root priviledges.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Tue, 12 Jan 2021 00:29:18 +0000 (00:29 +0000)]
mac80211: improve error handling when adding hostapd config
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Tue, 12 Jan 2021 00:28:17 +0000 (00:28 +0000)]
hostapd: improve error handling when adding supplicant config
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Etan Kissling [Wed, 13 Jan 2021 08:52:02 +0000 (09:52 +0100)]
hostapd: add multicast_to_unicast and per_sta_vif
This allows configuration of multicast_to_unicast and per_sta_vif options.
- multicast_to_unicast requests multicast-to-unicast conversion.
- per_sta_vif assigns each station its own AP_VLAN interface.
Signed-off-by: Etan Kissling <etan_kissling@apple.com>
Etan Kissling [Wed, 13 Jan 2021 00:01:24 +0000 (01:01 +0100)]
mbedtls: add config option to compile with hkdf
This adds a config option to allow compiling with HKDF algorithm support
to support applications that require this feature.
Signed-off-by: Etan Kissling <etan_kissling@apple.com>
Etan Kissling [Tue, 12 Jan 2021 23:54:08 +0000 (00:54 +0100)]
nf-conntrack: allow querying conntrack info in nfqueue
This allows libnetfilter_queue to access connection tracking information
by requesting NFQA_CFG_F_CONNTRACK. Connection tracking information is
provided in the NFQA_CT attribute.
CONFIG_NETFILTER_NETLINK_GLUE_CT enables the interaction between
nf_queue and nf_conntrack_netlink. Without this option, trying to access
connection tracking information results in "Operation not supported".
Signed-off-by: Etan Kissling <etan_kissling@apple.com>
Andy Walsh [Mon, 11 Jan 2021 14:22:30 +0000 (15:22 +0100)]
kernel: drop unneeded kernel version dependency
The current master only supports kernel 5.4, and there is no reason
to remove KERNEL_IO_URING for future kernels.
Drop the unneeded dependency.
Signed-off-by: Andy Walsh <andy.walsh44+github@gmail.com>
[improve commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
David Bauer [Mon, 7 Dec 2020 03:53:02 +0000 (04:53 +0100)]
zstd: fix package source
It looks like GitHub changed the URL path for release tarballs, thus the
download for the zstd package was always falling back to the OpenWrt
sources mirror.
Fix the GitHub URL for one which works. The file hash remains unchanged.
Signed-off-by: David Bauer <mail@david-bauer.net>
Jan Alexander [Sat, 9 Jan 2021 10:33:34 +0000 (11:33 +0100)]
uboot-envtools: add support for Aruba AP-303 and AP-365
Both devices use u-boot env variables to boot OpenWrt from its flash
partition. Using u-boot envtools, it is possible to change the bootcmd
back to the stock firmware partition directly from OpenWrt without
attaching a serial cable or even physically accessing the device.
Signed-off-by: Jan Alexander <jan@nalx.net>
Jan Alexander [Mon, 30 Nov 2020 10:51:16 +0000 (11:51 +0100)]
ipq806x: add support for Ubiquiti UniFi AC HD
Hardware
--------
SoC: Qualcomm IPQ8064
RAM: 512MB DDR3
Flash: 256MB NAND (Micron MT29F2G08ABBEAH4)
32MB SPI-NOR (Macronix MX25U25635F)
WLAN: Qualcomm Atheros QCA9994 4T4R b/g/n
Qualcomm Atheros QCA9994 4T4R a/n/ac
ETH: eth0 - SECONDARY (Atheros AR8033)
eth1 - MAIN (Atheros AR8033)
USB: USB-C
LED: Dome (white / blue)
BTN: Reset
Installation
------------
Copy the OpenWrt sysupgrade image to the /tmp directory of the device
using scp. Default IP address is 192.168.1.20 and default username and
password are "ubnt".
SSH to the device and write the bootselect flag to ensure it is booting
from the mtd partition the OpenWrt image will be written to. Verify the
output device below matches mtd partition "bootselect" using /proc/mtd.
> dd if=/dev/zero bs=1 count=1 seek=7 conv=notrunc of=/dev/mtd11
Write the OpenWrt sysupgrade image to the mtd partition labeled
"kernel0". Also verify the used partition device using /proc/mtd.
> dd if=/tmp/sysupgrade.bin of=/dev/mtdblock12
Reboot the device.
Back to stock
-------------
Use the TFTP recovery procedure with the Ubiquiti firmware image to
restore the vendor firmware.
Signed-off-by: Jan Alexander <jan@nalx.net>
David Bauer [Tue, 12 Jan 2021 23:33:10 +0000 (00:33 +0100)]
uboot-rockchip: update NanoPi R2S patches
Update the NanoPi R2S to the latest version submitted
upstream.
Signed-off-by: David Bauer <mail@david-bauer.net>
Marty Jones [Mon, 11 Jan 2021 23:35:29 +0000 (18:35 -0500)]
uboot-rockchip: update to v2021.01
Update the U-Boot to version v2021.01.
Run-tested: FriendlyARM NanoPi R2S
Radxa Rock Pi 4
Pine64 RockPro64
Signed-off-by: Marty Jones <mj8263788@gmail.com>
[format commit message]
Signed-off-by: David Bauer <mail@david-bauer.net>
David Bauer [Sun, 3 Jan 2021 20:43:57 +0000 (21:43 +0100)]
iw: enable HE PHY information for iw-tiny
Currently PHY information obtained from "iw phy" lacks information about
a PHYs HE capabilities when using the by default installed iw-tiny.
As there are already 802.11ax supported devices, enabled printing this
information for the by-default installed iw variant.
Signed-off-by: David Bauer <mail@david-bauer.net>
Rafał Miłecki [Wed, 13 Jan 2021 10:01:13 +0000 (11:01 +0100)]
bcm4908: backport BCM4908 integrated switch initial support
Upstream driver supports bridging ports. There is no support for
crossbar setup or CPU port(s) yet.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rafał Miłecki [Wed, 13 Jan 2021 06:41:34 +0000 (07:41 +0100)]
bcm4908: backport PMB (Power Management Bus) driver
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rafał Miłecki [Tue, 12 Jan 2021 22:27:08 +0000 (23:27 +0100)]
bcm4908: add simple PCIe reset controller support
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rafał Miłecki [Tue, 12 Jan 2021 22:03:41 +0000 (23:03 +0100)]
bcm4908: backport upstream DTS patches
1. Netgear R8000P DTS file
2. NAND fix
3. PCIe reset block
4. Integrated switch
5. PMB block
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rafał Miłecki [Fri, 8 Jan 2021 12:32:37 +0000 (13:32 +0100)]
bcm4908: initial work on the Broadcom BCM4908 target
BCM4906, BCM4908 and BCM49408 are SoCs with 64 bit ARMv8 B53 CPUs.
Upstream Linux is slowly getting support for that SoCs family so it
makes sense to add target for it.
This prepares initial support for:
1. Asus GT-AC5300
BCM4908 based device (4 CPUs) with 1024 MiB RAM, NAND, 8 LAN ports.
2. Netgear R8000P
BCM4906 based device (2 CPUs) with 512 MiB RAM, NAND, 4 LAN ports.
Flashing info will come later as we learn how to generate proper images.
It isn't usable yet (it only produces a bootable kernel) so "source-only"
is used.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Nick Hainke [Sat, 12 Dec 2020 10:23:54 +0000 (11:23 +0100)]
kernel: enable SRv6 support by enabling lwtunnel
Enable the ability to use segment routing based on IPv6. It allows the
packet to specify a path that the packet should take through the
network.
Lwtunnel allow an easy encapsulation of a package. You can just install
ip-full package and use it:
ip -6 route add 2003::/64 dev eth0 encap seg6 mode encap \
segs 2001::1,2002::2
An IPv6 package looks like this:
[IPv6 HDR][IPv6 RH][IPv6 HDR][Data...]
Netifd support:
https://git.openwrt.org/?p=project/netifd.git;
a=commit;h=
458b1a7e9473c150a40cae5d8be174f4bb03bd39
Increases imagesize by 24.125 KiB. Therefore, only enable for devices
with enough flash.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Thomas Nixon [Sat, 9 Jan 2021 22:04:48 +0000 (22:04 +0000)]
tools/ccache: find libzstd using rpath
Previously, ccache would end up using the system libzstd, which is not
supposed to be a build requirement.
Signed-off-by: Thomas Nixon <tom@tomn.co.uk>
David Bauer [Mon, 11 Jan 2021 04:57:52 +0000 (05:57 +0100)]
rockchip: add missing Kconfig symbols
When compiling with CONFIG_ALL_KMODS enabled, compilation might stall
due to unset rockchip-specific config symbols. Disable these to avoid
stalling this step.
Signed-off-by: David Bauer <mail@david-bauer.net>
Paul Spooren [Thu, 31 Dec 2020 04:11:54 +0000 (18:11 -1000)]
qemu: remove obsolete package
Instead of using an ancient qemu version in-tree the building machine
should just have qemu-utils installed.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Paul Spooren [Wed, 30 Dec 2020 19:08:17 +0000 (09:08 -1000)]
build/image: warn if missing qemu-img for VDI/VMDK
Currently `qemu-img` is used to convert raw x86 images to VDI and VMDK
images, used for virtual machines.
Having `qemu-img` in tree requires us to maintain an ancient version of
`qemu-utils`, which recently required extra work to compile with newer
compiler version.
This commit prints a warning message in case `qemu-img` is missing.
As a next step the in-tree version of `qemu-img` can be removed.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Daniel Golle [Mon, 7 Dec 2020 13:46:43 +0000 (13:46 +0000)]
mac80211: use hostapd PID returned from config_add
Use PID returned from config_add instead of querying procd when adding
configuration to hostapd.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Mon, 7 Dec 2020 13:12:46 +0000 (13:12 +0000)]
hostapd: return PID on config_add call
To simplify the way netifd acquires the PIDs of wpa_supplicant and
hostapd let the config_add method of both of them return the PID of the
called process. Use the returned PID instead of querying procd when
adding wpa_supplicant configuration.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Hans Dedecker [Sun, 10 Jan 2021 12:11:06 +0000 (13:11 +0100)]
glibc: update to latest 2.32 commit (BZ #24973)
0d9793e82a Fix buffer overrun in EUC-KR conversion module (bz #24973)
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Florian Fainelli [Sun, 13 Sep 2020 02:48:34 +0000 (19:48 -0700)]
kernel-defaults: Manage the enabling/disabling of ZSTD
Linux 5.9 introduces support for ZSTD ramdisk and initrd compression,
make sure we enable/disable the relevant options when building an
initramfs enabled kernel.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Florian Fainelli [Sun, 13 Sep 2020 00:09:53 +0000 (17:09 -0700)]
kernel-defaults: Delete external source tree user_headers
When we use an external kernel tree which may not have been fully
cleaned, there may be user_headers left which do not match the target
architecture, leading to build failures for packages that do an explicit
inclusion of user_headers (such as iproute2 or iptables). Make sure we
delete them while preparing the directory.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Curtis Deptuck [Thu, 3 Dec 2020 00:28:39 +0000 (17:28 -0700)]
iptables: update to 1.8.6
Update iptables to 1.8.6
ChangeLog:
https://netfilter.org/projects/iptables/files/changes-iptables-1.8.6.txt
Refresh patch:
101-remove-check-already.patch
Signed-off-by: Curtis Deptuck <curtdept@me.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [refresh patches]
John Audia [Wed, 6 Jan 2021 17:37:16 +0000 (12:37 -0500)]
kernel: bump 5.4 to 5.4.87
All modification by update_kernel.sh.
Build system: x86_64
Build-tested: ipq806x/R7800, bcm27xx/bcm2711
Run-tested: ipq806x/R7800
No dmesg regressions, everything functional
Compile-tested [*]: ath79/{generic,tiny}, ipq40xx, octeon,
ramips/mt7621, realtek, x86/64.
Run-tested [*]: ramips/mt7621 (DIR-878 A1, R6800, RT-AC57U),
octeon (EdgeRouter Lite).
Signed-off-by: John Audia <graysky@archlinux.us>
Tested-by: Stijn Segers <foss@volatilesystems.org> [*]
Stijn Segers [Fri, 8 Jan 2021 13:32:48 +0000 (14:32 +0100)]
realtek: add support for ZyXEL GS1900-8HP v1 and v2
The ZyXEL GS1900-8HP is an 8 port gigabit switch with PoE+ support.
There are two versions on the market (v1 & v2) which share similar
specs (same flash size and flash layout, same RAM size, same PoE+ power
envelope) but have a different case and board layout that they each
share with other GS1900 siblings.
The v1 seems to share its PCB and case with non-PoE GS1900-8; as such,
adding support for the GS1900-8 would probably be trivial. The v2 seems
to share its casing and platform with its already supported bigger
brother, the GS1900-10HP - its board looks the same, except for two
holes where the GS1900-10 has its SFP ports.
Like their 10 port sibling, both devices have a dual firmware layout.
Both GS1900-8HP boards have the same 70W PoE+ power budget. In order to
manipulate the PoE+, one needs the rtl83xx-poe package [1].
After careful consideration it was decided to go with separate images
for each version.
Specifications (v1)
-------------------
* SoC: Realtek RTL8380M 500 MHz MIPS 4KEc
* Flash: Macronix MX25L12835F 16 MiB
* RAM: Nanya NT5TU128M8HE-AC 128 MiB DDR2 SDRAM
* Ethernet: 8x 10/100/1000 Mbit
* PoE+: Broadcom BCM59111KMLG (IEEE 802.3at-2009 compliant, 2x)
* UART: 1 serial header with populated standard pin connector on the
left side of the PCB, towards the bottom. Pins are labeled:
+ VCC (3.3V)
+ TX
+ RX
+ GND
Specifications (v2)
-------------------
* SoC: Realtek RTL8380M 500 MHz MIPS 4KEc
* Flash: Macronix MX25L12835F 16 MiB
* RAM: Samsung K4B1G0846G 128 MiB DDR3 SDRAM
* Ethernet: 8x 10/100/1000 Mbit
* PoE+: Broadcom BCM59121B0KMLG (IEEE 802.3at-2009 compliant)
* UART: 1 angled serial header with populated standard pin connector
accessible from outside through the ventilation slits on the
side. Pins from top to bottom are clearly marked on the PCB:
+ VCC (3.3V)
+ TX
+ RX
+ GND
Serial connection parameters for both devices: 115200 8N1.
Installation
------------
Instructions are identical to those for the GS1900-10HP and apply both
to the GS1900-8HP v1 and v2 as well.
* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).
* Set up a TFTP server on your client and make it serve the initramfs
image.
* Connect serial, power up the switch, interrupt U-boot by hitting the
space bar, and enable the network:
> rtk network on
* Since the GS1900-10HP is a dual-partition device, you want to keep the
OEM firmware on the backup partition for the time being. OpenWrt can
only boot off the first partition anyway (hardcoded in the DTS). To
make sure we are manipulating the first partition, issue the following
commands:
> setsys bootpartition 0
> savesys
* Download the image onto the device and boot from it:
> tftpboot 0x84f00000 192.168.1.10:openwrt-realtek-generic-zyxel_gs1900-8hp-v{1,2}-initramfs-kernel.bin
> bootm
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade /tmp//tmp/openwrt-realtek-generic-zyxel_gs1900-8hp-v{1,2}-squashfs-sysupgrade.bin
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
[merge PoE case, keep device definitions separate, change all those
hashes in the commit message to something else so they don't get
removed when changing the commit ...]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Fri, 8 Jan 2021 19:37:37 +0000 (20:37 +0100)]
realtek: remove model prefix from LED label for ZyXEL GS1900
This is used as fixed status LED, so no migration is needed.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Stijn Segers [Fri, 8 Jan 2021 13:32:47 +0000 (14:32 +0100)]
realtek: introduce shared DTSI for GS1900 series
The ZyXEL GS1900-8HP v1, v2 and GS1900-10HP are all built on a similar
Realtek RTL8380M platform. Create a common DTSI in preparation for
GS1900-8HP support, and switch to the macros defined in rtl838x.dtsi.
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
[drop redundant includes, use &mdio directly, do not replace SFP
ports]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Pawel Dembicki [Mon, 4 Jan 2021 16:59:30 +0000 (17:59 +0100)]
kernel: add hid-cp2112 driver support
This patch adds kernel module for Silicon Labs CP2112 HID USB to SMBus
Master Bridge. This is a HID device driver which registers as an i2c
adapter and gpiochip to expose these functions of the CP2112.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Leon M. George [Tue, 5 Jan 2021 09:42:34 +0000 (10:42 +0100)]
ramips: remove trailing whitespace in Makefiles
Remove trailing whitespaces in two *.mk files.
Signed-off-by: Leon M. George <leon@georgemail.eu>
[fix title, add message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Stijn Segers [Wed, 6 Jan 2021 21:45:19 +0000 (22:45 +0100)]
realtek: ZyXEL: spell as done by manufacturer
ZyXEL spells its own name all uppercase with just the Y lowercase. Adapt
the realtek target to follow this (other OpenWrt targets already do so).
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
projects / openwrt / staging / thess.git / log