git.openwrt.org Git - openwrt/staging/blogic.git/log

mt76x02: avoid status_list.lock and sta->rate_ctrl_lock dependency

Move ieee80211_tx_status_ext() outside of status_list lock section
in order to avoid locking dependency and possible deadlock reposed by
LOCKDEP in below warning.

Also do mt76_tx_status_lock() just before it's needed.

[  440.224832] WARNING: possible circular locking dependency detected
[  440.224833] 5.1.0-rc2+ #22 Not tainted
[  440.224834] ------------------------------------------------------
[  440.224835] kworker/u16:28/2362 is trying to acquire lock:
[  440.224836] 0000000089b8cacf (&(&q->lock)->rlock#2){+.-.}, at: mt76_wake_tx_queue+0x4c/0xb0 [mt76]
[  440.224842]
               but task is already holding lock:
[  440.224842] 000000002cfedc59 (&(&sta->lock)->rlock){+.-.}, at: ieee80211_stop_tx_ba_cb+0x32/0x1f0 [mac80211]
[  440.224863]
               which lock already depends on the new lock.

[  440.224863]
               the existing dependency chain (in reverse order) is:
[  440.224864]
               -> #3 (&(&sta->lock)->rlock){+.-.}:
[  440.224869]        _raw_spin_lock_bh+0x34/0x40
[  440.224880]        ieee80211_start_tx_ba_session+0xe4/0x3d0 [mac80211]
[  440.224894]        minstrel_ht_get_rate+0x45c/0x510 [mac80211]
[  440.224906]        rate_control_get_rate+0xc1/0x140 [mac80211]
[  440.224918]        ieee80211_tx_h_rate_ctrl+0x195/0x3c0 [mac80211]
[  440.224930]        ieee80211_xmit_fast+0x26d/0xa50 [mac80211]
[  440.224942]        __ieee80211_subif_start_xmit+0xfc/0x310 [mac80211]
[  440.224954]        ieee80211_subif_start_xmit+0x38/0x390 [mac80211]
[  440.224956]        dev_hard_start_xmit+0xb8/0x300
[  440.224957]        __dev_queue_xmit+0x7d4/0xbb0
[  440.224968]        ip6_finish_output2+0x246/0x860 [ipv6]
[  440.224978]        mld_sendpack+0x1bd/0x360 [ipv6]
[  440.224987]        mld_ifc_timer_expire+0x1a4/0x2f0 [ipv6]
[  440.224989]        call_timer_fn+0x89/0x2a0
[  440.224990]        run_timer_softirq+0x1bd/0x4d0
[  440.224992]        __do_softirq+0xdb/0x47c
[  440.224994]        irq_exit+0xfa/0x100
[  440.224996]        smp_apic_timer_interrupt+0x9a/0x220
[  440.224997]        apic_timer_interrupt+0xf/0x20
[  440.224999]        cpuidle_enter_state+0xc1/0x470
[  440.225000]        do_idle+0x21a/0x260
[  440.225001]        cpu_startup_entry+0x19/0x20
[  440.225004]        start_secondary+0x135/0x170
[  440.225006]        secondary_startup_64+0xa4/0xb0
[  440.225007]
               -> #2 (&(&sta->rate_ctrl_lock)->rlock){+.-.}:
[  440.225009]        _raw_spin_lock_bh+0x34/0x40
[  440.225022]        rate_control_tx_status+0x4f/0xb0 [mac80211]
[  440.225031]        ieee80211_tx_status_ext+0x142/0x1a0 [mac80211]
[  440.225035]        mt76x02_send_tx_status+0x2e4/0x340 [mt76x02_lib]
[  440.225037]        mt76x02_tx_status_data+0x31/0x40 [mt76x02_lib]
[  440.225040]        mt76u_tx_status_data+0x51/0xa0 [mt76_usb]
[  440.225042]        process_one_work+0x237/0x5d0
[  440.225043]        worker_thread+0x3c/0x390
[  440.225045]        kthread+0x11d/0x140
[  440.225046]        ret_from_fork+0x3a/0x50
[  440.225047]
               -> #1 (&(&list->lock)->rlock#8){+.-.}:
[  440.225049]        _raw_spin_lock_bh+0x34/0x40
[  440.225052]        mt76_tx_status_skb_add+0x51/0x100 [mt76]
[  440.225054]        mt76x02u_tx_prepare_skb+0xbd/0x116 [mt76x02_usb]
[  440.225056]        mt76u_tx_queue_skb+0x5f/0x180 [mt76_usb]
[  440.225058]        mt76_tx+0x93/0x190 [mt76]
[  440.225070]        ieee80211_tx_frags+0x148/0x210 [mac80211]
[  440.225081]        __ieee80211_tx+0x75/0x1b0 [mac80211]
[  440.225092]        ieee80211_tx+0xde/0x110 [mac80211]
[  440.225105]        __ieee80211_tx_skb_tid_band+0x72/0x90 [mac80211]
[  440.225122]        ieee80211_send_auth+0x1f3/0x360 [mac80211]
[  440.225141]        ieee80211_auth.cold.40+0x6c/0x100 [mac80211]
[  440.225156]        ieee80211_mgd_auth.cold.50+0x132/0x15f [mac80211]
[  440.225171]        cfg80211_mlme_auth+0x149/0x360 [cfg80211]
[  440.225181]        nl80211_authenticate+0x273/0x2e0 [cfg80211]
[  440.225183]        genl_family_rcv_msg+0x196/0x3a0
[  440.225184]        genl_rcv_msg+0x47/0x8e
[  440.225185]        netlink_rcv_skb+0x3a/0xf0
[  440.225187]        genl_rcv+0x24/0x40
[  440.225188]        netlink_unicast+0x16d/0x210
[  440.225189]        netlink_sendmsg+0x204/0x3b0
[  440.225191]        sock_sendmsg+0x36/0x40
[  440.225193]        ___sys_sendmsg+0x259/0x2b0
[  440.225194]        __sys_sendmsg+0x47/0x80
[  440.225196]        do_syscall_64+0x60/0x1f0
[  440.225197]        entry_SYSCALL_64_after_hwframe+0x49/0xbe
[  440.225198]
               -> #0 (&(&q->lock)->rlock#2){+.-.}:
[  440.225200]        lock_acquire+0xb9/0x1a0
[  440.225202]        _raw_spin_lock_bh+0x34/0x40
[  440.225204]        mt76_wake_tx_queue+0x4c/0xb0 [mt76]
[  440.225215]        ieee80211_agg_start_txq+0xe8/0x2b0 [mac80211]
[  440.225225]        ieee80211_stop_tx_ba_cb+0xb8/0x1f0 [mac80211]
[  440.225235]        ieee80211_ba_session_work+0x1c1/0x2f0 [mac80211]
[  440.225236]        process_one_work+0x237/0x5d0
[  440.225237]        worker_thread+0x3c/0x390
[  440.225239]        kthread+0x11d/0x140
[  440.225240]        ret_from_fork+0x3a/0x50
[  440.225240]
               other info that might help us debug this:

[  440.225241] Chain exists of:
                 &(&q->lock)->rlock#2 --> &(&sta->rate_ctrl_lock)->rlock --> &(&sta->lock)->rlock

[  440.225243]  Possible unsafe locking scenario:

[  440.225244]        CPU0                    CPU1
[  440.225244]        ----                    ----
[  440.225245]   lock(&(&sta->lock)->rlock);
[  440.225245]                                lock(&(&sta->rate_ctrl_lock)->rlock);
[  440.225246]                                lock(&(&sta->lock)->rlock);
[  440.225247]   lock(&(&q->lock)->rlock#2);
[  440.225248]
                *** DEADLOCK ***

[  440.225249] 5 locks held by kworker/u16:28/2362:
[  440.225250]  #0: 0000000048fcd291 ((wq_completion)phy0){+.+.}, at: process_one_work+0x1b5/0x5d0
[  440.225252]  #1: 00000000f1c6828f ((work_completion)(&sta->ampdu_mlme.work)){+.+.}, at: process_one_work+0x1b5/0x5d0
[  440.225254]  #2: 00000000433d2b2c (&sta->ampdu_mlme.mtx){+.+.}, at: ieee80211_ba_session_work+0x5c/0x2f0 [mac80211]
[  440.225265]  #3: 000000002cfedc59 (&(&sta->lock)->rlock){+.-.}, at: ieee80211_stop_tx_ba_cb+0x32/0x1f0 [mac80211]
[  440.225276]  #4: 000000009d7b9a44 (rcu_read_lock){....}, at: ieee80211_agg_start_txq+0x33/0x2b0 [mac80211]
[  440.225286]
               stack backtrace:
[  440.225288] CPU: 2 PID: 2362 Comm: kworker/u16:28 Not tainted 5.1.0-rc2+ #22
[  440.225289] Hardware name: LENOVO 20KGS23S0P/20KGS23S0P, BIOS N23ET55W (1.30 ) 08/31/2018
[  440.225300] Workqueue: phy0 ieee80211_ba_session_work [mac80211]
[  440.225301] Call Trace:
[  440.225304]  dump_stack+0x85/0xc0
[  440.225306]  print_circular_bug.isra.38.cold.58+0x15c/0x195
[  440.225307]  check_prev_add.constprop.48+0x5f0/0xc00
[  440.225309]  ? check_prev_add.constprop.48+0x39d/0xc00
[  440.225311]  ? __lock_acquire+0x41d/0x1100
[  440.225312]  __lock_acquire+0xd98/0x1100
[  440.225313]  ? __lock_acquire+0x41d/0x1100
[  440.225315]  lock_acquire+0xb9/0x1a0
[  440.225317]  ? mt76_wake_tx_queue+0x4c/0xb0 [mt76]
[  440.225319]  _raw_spin_lock_bh+0x34/0x40
[  440.225321]  ? mt76_wake_tx_queue+0x4c/0xb0 [mt76]
[  440.225323]  mt76_wake_tx_queue+0x4c/0xb0 [mt76]
[  440.225334]  ieee80211_agg_start_txq+0xe8/0x2b0 [mac80211]
[  440.225344]  ieee80211_stop_tx_ba_cb+0xb8/0x1f0 [mac80211]
[  440.225354]  ieee80211_ba_session_work+0x1c1/0x2f0 [mac80211]
[  440.225356]  process_one_work+0x237/0x5d0
[  440.225358]  worker_thread+0x3c/0x390
[  440.225359]  ? wq_calc_node_cpumask+0x70/0x70
[  440.225360]  kthread+0x11d/0x140
[  440.225362]  ? kthread_create_on_node+0x40/0x40
[  440.225363]  ret_from_fork+0x3a/0x50

Cc: stable@vger.kernel.org
Fixes: 88046b2c9f6d ("mt76: add support for reporting tx status with skb")
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rt2x00: do not increment sequence number while re-transmitting

Currently rt2x00 devices retransmit the management frames with
incremented sequence number if hardware is assigning the sequence.

This is HW bug fixed already for non-QOS data frames, but it should
be fixed for management frames except beacon.

Without fix retransmitted frames have wrong SN:

AlphaNet_e8:fb:36 Vivotek_52:31:51 Authentication, SN=1648, FN=0, Flags=........C Frame is not being retransmitted 1648 1
AlphaNet_e8:fb:36 Vivotek_52:31:51 Authentication, SN=1649, FN=0, Flags=....R...C Frame is being retransmitted 1649 1
AlphaNet_e8:fb:36 Vivotek_52:31:51 Authentication, SN=1650, FN=0, Flags=....R...C Frame is being retransmitted 1650 1

With the fix SN stays correctly the same:

88:6a:e3:e8:f9:a2 8c:f5:a3:88:76:87 Authentication, SN=1450, FN=0, Flags=........C
88:6a:e3:e8:f9:a2 8c:f5:a3:88:76:87 Authentication, SN=1450, FN=0, Flags=....R...C
88:6a:e3:e8:f9:a2 8c:f5:a3:88:76:87 Authentication, SN=1450, FN=0, Flags=....R...C

Cc: stable@vger.kernel.org
Signed-off-by: Vijayakumar Durai <vijayakumar.durai1@vivint.com>
[sgruszka: simplify code, change comments and changelog]
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mt76: mt7603: send BAR after powersave wakeup

Now that the sequence number allocation is fixed, we can finally send a BAR
at powersave wakeup time to refresh the receiver side reorder window

Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mt76: mt7603: fix sequence number assignment

If the MT_TXD3_SN_VALID flag is not set in the tx descriptor, the hardware
assigns the sequence number. However, the rest of the code assumes that the
sequence number specified in the 802.11 header gets transmitted.
This was causing issues with the aggregation setup, which worked for the
initial one (where the sequence numbers were still close), but not for
further teardown/re-establishing of sessions.

Additionally, the overwrite of the TID sequence number in WTBL2 was resetting
the hardware assigned sequence numbers, causing them to drift further apart.

Fix this by using the software assigned sequence numbers

Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mt76: mt7603: add missing initialization for dev->ps_lock

Fixes lockdep complaint and a potential race condition

Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Merge tag 'iwlwifi-for-kalle-2019-03-22' of git://git./linux/kernel/git/iwlwifi/iwlwifi-fixes

First batch of iwlwifi fixes intended for v5.1

* add some new PCI IDs (plus a struct name change they depend on);
* fix crypto with new devices, namely 22560 and above;
* a bunch of fixes (and a dependency) for the new debugging infra;

Merge git://git./pub/scm/linux/kernel/git/bpf/bpf

Daniel Borkmann says:

====================
pull-request: bpf 2019-03-29

The following pull-request contains BPF updates for your *net* tree.

The main changes are:

1) Bug fix in BTF deduplication that was mishandling an equivalence
   comparison, from Andrii.

2) libbpf Makefile fixes to properly link against libelf for the shared
   object and to actually export AF_XDP's xsk.h header, from Björn.

3) Fix use after free in bpf inode eviction, from Daniel.

4) Fix a bug in skb creation out of cpumap redirect, from Jesper.

5) Remove an unnecessary and triggerable WARN_ONCE() in max number
   of call stack frames checking in verifier, from Paul.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'mlx5-fixes-2019-03-29' of git://git./linux/kernel/git/saeed/linux

Saeed Mahameed says:

====================
Mellanox, mlx5 fixes 2019-03-29

This series introduces some fixes to mlx5 driver.

Please pull and let me know if there is any problem.

For -stable v4.11
('net/mlx5: Decrease default mr cache size')

For -stable v4.12
('net/mlx5e: Add a lock on tir list')

For -stable v4.13
('net/mlx5e: Fix error handling when refreshing TIRs')

For -stable v4.18
('net/mlx5e: Update xon formula')

For -stable v4.19
('net: mlx5: Add a missing check on idr_find, free buf')
('net/mlx5e: Update xoff formula')

net-next merge Note:
When merged with net-next the following simple conflict will appear,

drivers/net/ethernet/mellanox/mlx5/core/en/port_buffer.c

++<<<<<<< HEAD (net)
+ *   max_mtu: netdev's max_mtu
++=======
+  *    @mtu: device's MTU
++>>>>>>> net-next

To resolve: just replace the line in net-next
*    @mtu: device's MTU
to
*    @max_mtu: netdev's max_mtu
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

Revert "cxgb4: Update 1.23.3.0 as the latest firmware supported."

This reverts commit 4d31c4fa3f9ef7b7e2e79fd57d21290f64c938f5.

Accidently applied this to the wrong tree.

Signed-off-by: David S. Miller <davem@davemloft.net>

cxgb4: Update 1.23.3.0 as the latest firmware supported.

Change t4fw_version.h to update latest firmware version
number to 1.23.3.0.

Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ethtool: not call vzalloc for zero sized memory request

NULL or ZERO_SIZE_PTR will be returned for zero sized memory
request, and derefencing them will lead to a segfault

so it is unnecessory to call vzalloc for zero sized memory
request and not call functions which maybe derefence the
NULL allocated memory

this also fixes a possible memory leak if phy_ethtool_get_stats
returns error, memory should be freed before exit

Signed-off-by: Li RongQing <lirongqing@baidu.com>
Reviewed-by: Wang Li <wangli39@baidu.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: tls: prevent false connection termination with offload

Only decrypt_internal() performs zero copy on rx, all paths
which don't hit decrypt_internal() must set zc to false,
otherwise tls_sw_recvmsg() may return 0 causing the application
to believe that that connection got closed.

Currently this happens with device offload when new record
is first read from.

Fixes: d069b780e367 ("tls: Fix tls_device receive")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reported-by: David Beckett <david.beckett@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

hv_netvsc: Fix unwanted wakeup after tx_disable

After queue stopped, the wakeup mechanism may wake it up again
when ring buffer usage is lower than a threshold. This may cause
send path panic on NULL pointer when we stopped all tx queues in
netvsc_detach and start removing the netvsc device.

This patch fix it by adding a tx_disable flag to prevent unwanted
queue wakeup.

Fixes: 7b2ee50c0cd5 ("hv_netvsc: common detach logic")
Reported-by: Mohammed Gamal <mgamal@redhat.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bonding: show full hw address in sysfs for slave entries

Bond expects ethernet hwaddr for its slave, but it can be longer than 6
bytes - infiniband interface for example.

# cat /sys/devices/<skipped>/net/ib0/address
80:00:02:08:fe:80:00:00:00:00:00:00:7c:fe:90:03:00:be:5d:e1

# cat /sys/devices/<skipped>/net/ib0/bonding_slave/perm_hwaddr
80:00:02:08:fe:80

So print full hwaddr in sysfs "bonding_slave/perm_hwaddr" as well.

Signed-off-by: Konstantin Khorenko <khorenko@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/mlx5e: Consider tunnel type for encap contexts

The driver allocates an encap context based on the tunnel properties,
and reuse that context for all flows using the same tunnel properties.
Commit df2ef3bff193 ("net/mlx5e: Add GRE protocol offloading")
introduced another tunnel protocol other than the single VXLAN
previously supported. A flow that uses a tunnel with the same tunnel
properties but with a different tunnel type (GRE vs VXLAN for example)
would mistakenly reuse the previous alocated context, causing the
traffic to be sent with the wrong encapsulation. Fix that by
considering the tunnel type for encap contexts.

Fixes: df2ef3bff193 ("net/mlx5e: Add GRE protocol offloading")
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

net/mlx5e: Update xon formula

Set xon = xoff - netdev's max_mtu.
netdev's max_mtu will give enough time for the pause frame to
arrive at the sender.

Fixes: 0696d60853d5 ("net/mlx5e: Receive buffer configuration")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

net/mlx5e: Update xoff formula

Set minimum speed in xoff threshold formula to 40Gbps

Fixes: 0696d60853d5 ("net/mlx5e: Receive buffer configuration")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

net/mlx5: E-Switch, fix syndrome (0x678139) when turn on vepa

Make sure the struct mlx5_flow_destination is zero before
filling in the field.

Fixes: 8da202b24913 ("net/mlx5: E-Switch, Add support for VEPA in legacy mode.")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

net/mlx5: E-Switch, Fix esw manager vport indication for more vport commands

Traditionally, the PF (Physical Function) which resides on vport 0 was
the E-switch manager. Since the ECPF (Embedded CPU Physical Function),
which resides on vport 0xfffe, was introduced as the E-Switch manager,
the assumption that the E-switch manager is on vport 0 is incorrect.

Since the eswitch code already uses the actual vport value, all we
need is to always set other_vport=1.

Signed-off-by: Omri Kahalon <omrik@mellanox.com>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

net/mlx5: E-Switch, Protect from invalid memory access in offload fdb table

The esw offloads structures share a union with the legacy mode structs.
Reset the offloads struct to zero in init to protect from null
assumptions made by the legacy mode code.

Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

net/mlx5e: Correctly use the namespace type when allocating pedit action

The capacity of FDB offloading and NIC offloading table are
different, and when allocating the pedit actions, we should
use the correct namespace type.

Fixes: c500c86b0c75d ("net/mlx5e: support for two independent packet edit actions")
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

net/mlx5: E-Switch, Fix access to invalid memory when toggling esw modes

The esw fdb table has a union of legacy and offloads members.
So if we were in a certain esw mode we could set some memebers and not
set null which is fine as on destroy path and don't care.
But then moving from legacy to switchdev a second time, the cleanup flow
of legacy mode checks if a struct member was in use if it's not null so
we need to make sure to reset the code to null when we init legacy mode.

Fixes: 8da202b24913 ("net/mlx5: E-Switch, Add support for VEPA in legacy mode.")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

net/mlx5: ethtool, Allow legacy link-modes configuration via non-extended ptys

Allow configuration of legacy link-modes even when extended link-modes
are supported. This requires reading of legacy advertisement even when
extended link-modes are supported. Since legacy and extended
advertisement are mutually excluded, wait for empty reply from extended
advertisement before reading legacy advertisement.

Fixes: 6a897372417e ("net/mlx5: ethtool, Add ethtool support for 50Gbps per lane link modes")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

net/mlx5: ethtool, Fix type analysis of advertised link-mode

Ethtool option set_link_ksettings allows setting of legacy link-modes
or extended link-modes. Refine the decision of which type of link-modes
is set.

Fixes: 6a897372417e ("net/mlx5: ethtool, Add ethtool support for 50Gbps per lane link modes")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

net/mlx5e: Add a lock on tir list

Refresh tirs is looping over a global list of tirs while netdevs are
adding and removing tirs from that list. That is why a lock is
required.

Fixes: 724b2aa15126 ("net/mlx5e: TIRs management refactoring")
Signed-off-by: Yuval Avnery <yuvalav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

net: mlx5: Add a missing check on idr_find, free buf

idr_find() can return a NULL value to 'flow' which is used without a
check. The patch adds a check to avoid potential NULL pointer dereference.

In case of mlx5_fpga_sbu_conn_sendmsg() failure, free buf allocated
using kzalloc.

Fixes: ab412e1dd7db ("net/mlx5: Accel, add TLS rx offload routines")
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

net/mlx5e: Allow IPv4 ttl & IPv6 hop_limit rewrite for all L4 protocols

For some protocols we are not allowing IP header rewrite offload, since
the HW is not capable to properly adjust the l4 checksum. However, TTL
& HOPLIMIT modification can be done for all IP protocols, because they
are not part of the pseudo header taken into account for checksum.

Fixes: 738678817573 ("drivers: net: use flow action infrastructure")
Signed-off-by: Dmytro Linkin <dmitrolin@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

net/mlx5e: Fix error handling when refreshing TIRs

Previously, a false positive would be caught if the TIRs list is
empty, since the err value was initialized to -ENOMEM, and was only
updated if a TIR is refreshed. This is resolved by initializing the
err value to zero.

Fixes: b676f653896a ("net/mlx5e: Refactor refresh TIRs")
Signed-off-by: Gavi Teitz <gavi@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

net/mlx5: Decrease default mr cache size

Delete initialization of high order entries in mr cache to decrease initial
memory footprint. When required, the administrator can populate the
entries with memory keys via the /sys interface.

This approach is very helpful to significantly reduce the per HW function
memory footprint in virtualization environments such as SRIOV.

Fixes: 9603b61de1ee ("mlx5: Move pci device handling from mlx5_ib to mlx5_core")
Signed-off-by: Artemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reported-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

xdp: fix cpumap redirect SKB creation bug

We want to avoid leaking pointer info from xdp_frame (that is placed in
top of frame) like commit 6dfb970d3dbd ("xdp: avoid leaking info stored in
frame data on page reuse"), and followup commit 97e19cce05e5 ("bpf:
reserve xdp_frame size in xdp headroom") that reserve this headroom.

These changes also affected how cpumap constructed SKBs, as xdpf->headroom
size changed, the skb data starting point were in-effect shifted with 32
bytes (sizeof xdp_frame). This was still okay, as the cpumap frame_size
calculation also included xdpf->headroom which were reduced by same amount.

A bug was introduced in commit 77ea5f4cbe20 ("bpf/cpumap: make sure
frame_size for build_skb is aligned if headroom isn't"), where the
xdpf->headroom became part of the SKB_DATA_ALIGN rounding up. This
round-up to find the frame_size is in principle still correct as it does
not exceed the 2048 bytes frame_size (which is max for ixgbe and i40e),
but the 32 bytes offset of pkt_data_start puts this over the 2048 bytes
limit. This cause skb_shared_info to spill into next frame. It is a little
hard to trigger, as the SKB need to use above 15 skb_shinfo->frags[] as
far as I calculate. This does happen in practise for TCP streams when
skb_try_coalesce() kicks in.

KASAN can be used to detect these wrong memory accesses, I've seen:
BUG: KASAN: use-after-free in skb_try_coalesce+0x3cb/0x760
BUG: KASAN: wild-memory-access in skb_release_data+0xe2/0x250

Driver veth also construct a SKB from xdp_frame in this way, but is not
affected, as it doesn't reserve/deduct the room (used by xdp_frame) from
the SKB headroom. Instead is clears the pointers via xdp_scrub_frame(),
and allows SKB to use this area.

The fix in this patch is to do like veth and instead allow SKB to (re)use
the area occupied by xdp_frame, by clearing via xdp_scrub_frame(). (This
does kill the idea of the SKB being able to access (mem) info from this
area, but I guess it was a bad idea anyhow, and it was already killed by
the veth changes.)

Fixes: 77ea5f4cbe20 ("bpf/cpumap: make sure frame_size for build_skb is aligned if headroom isn't")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

net: core: netif_receive_skb_list: unlist skb before passing to pt->func

__netif_receive_skb_list_ptype() leaves skb->next poisoned before passing
it to pt_prev->func handler, what may produce (in certain cases, e.g. DSA
setup) crashes like:

[ 88.606777] CPU 0 Unable to handle kernel paging request at virtual address 0000000e, epc == 80687078, ra == 8052cc7c
[ 88.618666] Oops[#1]:
[ 88.621196] CPU: 0 PID: 0 Comm: swapper Not tainted 5.1.0-rc2-dlink-00206-g4192a172-dirty #1473
[ 88.630885] $ 0 : 00000000 10000400 00000002 864d7850
[ 88.636709] $ 4 : 87c0ddf0 864d7800 87c0ddf0 00000000
[ 88.642526] $ 8 : 00000000 49600000 00000001 00000001
[ 88.648342] $12 : 00000000 c288617b dadbee27 25d17c41
[ 88.654159] $16 : 87c0ddf0 85cff080 80790000 fffffffd
[ 88.659975] $20 : 80797b20 ffffffff 00000001 864d7800
[ 88.665793] $24 : 00000000 8011e658
[ 88.671609] $28 : 80790000 87c0dbc0 87cabf00 8052cc7c
[ 88.677427] Hi : 00000003
[ 88.680622] Lo : 7b5b4220
[ 88.683840] epc : 80687078 vlan_dev_hard_start_xmit+0x1c/0x1a0
[ 88.690532] ra : 8052cc7c dev_hard_start_xmit+0xac/0x188
[ 88.696734] Status: 10000404 IEp
[ 88.700422] Cause : 50000008 (ExcCode 02)
[ 88.704874] BadVA : 0000000e
[ 88.708069] PrId : 0001a120 (MIPS interAptiv (multi))
[ 88.713005] Modules linked in:
[ 88.716407] Process swapper (pid: 0, threadinfo=(ptrval), task=(ptrval), tls=00000000)
[ 88.725219] Stack : 85f61c28 00000000 0000000e 80780000 87c0ddf0 85cff080 80790000 8052cc7c
[ 88.734529] 87cabf00 00000000 00000001 85f5fb40 807b0000 864d7850 87cabf00 807d0000
[ 88.743839] 864d7800 8655f600 00000000 85cff080 87c1c000 0000006a 00000000 8052d96c
[ 88.753149] 807a0000 8057adb8 87c0dcc8 87c0dc50 85cfff08 00000558 87cabf00 85f58c50
[ 88.762460] 00000002 85f58c00 864d7800 80543308 fffffff4 00000001 85f58c00 864d7800
[ 88.771770] ...
[ 88.774483] Call Trace:
[ 88.777199] [<80687078>] vlan_dev_hard_start_xmit+0x1c/0x1a0
[ 88.783504] [<8052cc7c>] dev_hard_start_xmit+0xac/0x188
[ 88.789326] [<8052d96c>] __dev_queue_xmit+0x6e8/0x7d4
[ 88.794955] [<805a8640>] ip_finish_output2+0x238/0x4d0
[ 88.800677] [<805ab6a0>] ip_output+0xc8/0x140
[ 88.805526] [<805a68f4>] ip_forward+0x364/0x560
[ 88.810567] [<805a4ff8>] ip_rcv+0x48/0xe4
[ 88.815030] [<80528d44>] __netif_receive_skb_one_core+0x44/0x58
[ 88.821635] [<8067f220>] dsa_switch_rcv+0x108/0x1ac
[ 88.827067] [<80528f80>] __netif_receive_skb_list_core+0x228/0x26c
[ 88.833951] [<8052ed84>] netif_receive_skb_list+0x1d4/0x394
[ 88.840160] [<80355a88>] lunar_rx_poll+0x38c/0x828
[ 88.845496] [<8052fa78>] net_rx_action+0x14c/0x3cc
[ 88.850835] [<806ad300>] __do_softirq+0x178/0x338
[ 88.856077] [<8012a2d4>] irq_exit+0xbc/0x100
[ 88.860846] [<802f8b70>] plat_irq_dispatch+0xc0/0x144
[ 88.866477] [<80105974>] handle_int+0x14c/0x158
[ 88.871516] [<806acfb0>] r4k_wait+0x30/0x40
[ 88.876462] Code: afb10014 8c8200a0 00803025 <9443000c> 94a20468 00000000 10620042 00a08025 9605046a
[ 88.887332]
[ 88.888982] ---[ end trace eb863d007da11cf1 ]---
[ 88.894122] Kernel panic - not syncing: Fatal exception in interrupt
[ 88.901202] ---[ end Kernel panic - not syncing: Fatal exception in interrupt ]---

Fix this by pulling skb off the sublist and zeroing skb->next pointer
before calling ptype callback.

Fixes: 88eb1944e18c ("net: core: propagate SKB lists through packet_type lookup")
Reviewed-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: Alexander Lobakin <alobakin@dlink.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: rds: force to destroy connection if t_sock is NULL in rds_tcp_kill_sock().

When it is to cleanup net namespace, rds_tcp_exit_net() will call
rds_tcp_kill_sock(), if t_sock is NULL, it will not call
rds_conn_destroy(), rds_conn_path_destroy() and rds_tcp_conn_free() to free
connection, and the worker cp_conn_w is not stopped, afterwards the net is freed in
net_drop_ns(); While cp_conn_w rds_connect_worker() will call rds_tcp_conn_path_connect()
and reference 'net' which has already been freed.

In rds_tcp_conn_path_connect(), rds_tcp_set_callbacks() will set t_sock = sock before
sock->ops->connect, but if connect() is failed, it will call
rds_tcp_restore_callbacks() and set t_sock = NULL, if connect is always
failed, rds_connect_worker() will try to reconnect all the time, so
rds_tcp_kill_sock() will never to cancel worker cp_conn_w and free the
connections.

Therefore, the condition !tc->t_sock is not needed if it is going to do
cleanup_net->rds_tcp_exit_net->rds_tcp_kill_sock, because tc->t_sock is always
NULL, and there is on other path to cancel cp_conn_w and free
connection. So this patch is to fix this.

rds_tcp_kill_sock():
...
if (net != c_net || !tc->t_sock)
...
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
==================================================================
BUG: KASAN: use-after-free in inet_create+0xbcc/0xd28
net/ipv4/af_inet.c:340
Read of size 4 at addr ffff8003496a4684 by task kworker/u8:4/3721

CPU: 3 PID: 3721 Comm: kworker/u8:4 Not tainted 5.1.0 #11
Hardware name: linux,dummy-virt (DT)
Workqueue: krdsd rds_connect_worker
Call trace:
dump_backtrace+0x0/0x3c0 arch/arm64/kernel/time.c:53
show_stack+0x28/0x38 arch/arm64/kernel/traps.c:152
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x120/0x188 lib/dump_stack.c:113
print_address_description+0x68/0x278 mm/kasan/report.c:253
kasan_report_error mm/kasan/report.c:351 [inline]
kasan_report+0x21c/0x348 mm/kasan/report.c:409
__asan_report_load4_noabort+0x30/0x40 mm/kasan/report.c:429
inet_create+0xbcc/0xd28 net/ipv4/af_inet.c:340
__sock_create+0x4f8/0x770 net/socket.c:1276
sock_create_kern+0x50/0x68 net/socket.c:1322
rds_tcp_conn_path_connect+0x2b4/0x690 net/rds/tcp_connect.c:114
rds_connect_worker+0x108/0x1d0 net/rds/threads.c:175
process_one_work+0x6e8/0x1700 kernel/workqueue.c:2153
worker_thread+0x3b0/0xdd0 kernel/workqueue.c:2296
kthread+0x2f0/0x378 kernel/kthread.c:255
ret_from_fork+0x10/0x18 arch/arm64/kernel/entry.S:1117

Allocated by task 687:
save_stack mm/kasan/kasan.c:448 [inline]
set_track mm/kasan/kasan.c:460 [inline]
kasan_kmalloc+0xd4/0x180 mm/kasan/kasan.c:553
kasan_slab_alloc+0x14/0x20 mm/kasan/kasan.c:490
slab_post_alloc_hook mm/slab.h:444 [inline]
slab_alloc_node mm/slub.c:2705 [inline]
slab_alloc mm/slub.c:2713 [inline]
kmem_cache_alloc+0x14c/0x388 mm/slub.c:2718
kmem_cache_zalloc include/linux/slab.h:697 [inline]
net_alloc net/core/net_namespace.c:384 [inline]
copy_net_ns+0xc4/0x2d0 net/core/net_namespace.c:424
create_new_namespaces+0x300/0x658 kernel/nsproxy.c:107
unshare_nsproxy_namespaces+0xa0/0x198 kernel/nsproxy.c:206
ksys_unshare+0x340/0x628 kernel/fork.c:2577
__do_sys_unshare kernel/fork.c:2645 [inline]
__se_sys_unshare kernel/fork.c:2643 [inline]
__arm64_sys_unshare+0x38/0x58 kernel/fork.c:2643
__invoke_syscall arch/arm64/kernel/syscall.c:35 [inline]
invoke_syscall arch/arm64/kernel/syscall.c:47 [inline]
el0_svc_common+0x168/0x390 arch/arm64/kernel/syscall.c:83
el0_svc_handler+0x60/0xd0 arch/arm64/kernel/syscall.c:129
el0_svc+0x8/0xc arch/arm64/kernel/entry.S:960

Freed by task 264:
save_stack mm/kasan/kasan.c:448 [inline]
set_track mm/kasan/kasan.c:460 [inline]
__kasan_slab_free+0x114/0x220 mm/kasan/kasan.c:521
kasan_slab_free+0x10/0x18 mm/kasan/kasan.c:528
slab_free_hook mm/slub.c:1370 [inline]
slab_free_freelist_hook mm/slub.c:1397 [inline]
slab_free mm/slub.c:2952 [inline]
kmem_cache_free+0xb8/0x3a8 mm/slub.c:2968
net_free net/core/net_namespace.c:400 [inline]
net_drop_ns.part.6+0x78/0x90 net/core/net_namespace.c:407
net_drop_ns net/core/net_namespace.c:406 [inline]
cleanup_net+0x53c/0x6d8 net/core/net_namespace.c:569
process_one_work+0x6e8/0x1700 kernel/workqueue.c:2153
worker_thread+0x3b0/0xdd0 kernel/workqueue.c:2296
kthread+0x2f0/0x378 kernel/kthread.c:255
ret_from_fork+0x10/0x18 arch/arm64/kernel/entry.S:1117

The buggy address belongs to the object at ffff8003496a3f80
which belongs to the cache net_namespace of size 7872
The buggy address is located 1796 bytes inside of
7872-byte region [ffff8003496a3f80, ffff8003496a5e40)
The buggy address belongs to the page:
page:ffff7e000d25a800 count:1 mapcount:0 mapping:ffff80036ce4b000
index:0x0 compound_mapcount: 0
flags: 0xffffe0000008100(slab|head)
raw: 0ffffe0000008100 dead000000000100 dead000000000200 ffff80036ce4b000
raw: 0000000000000000 0000000080040004 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected

Memory state around the buggy address:
ffff8003496a4580: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff8003496a4600: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
>ffff8003496a4680: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^
ffff8003496a4700: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff8003496a4780: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
==================================================================

Fixes: 467fa15356ac("RDS-TCP: Support multiple RDS-TCP listen endpoints, one per netns.")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

openvswitch: fix flow actions reallocation

The flow action buffer can be resized if it's not big enough to contain
all the requested flow actions. However, this resize doesn't take into
account the new requested size, the buffer is only increased by a factor
of 2x. This might be not enough to contain the new data, causing a
buffer overflow, for example:

[   42.044472] =============================================================================
[   42.045608] BUG kmalloc-96 (Not tainted): Redzone overwritten
[   42.046415] -----------------------------------------------------------------------------

[   42.047715] Disabling lock debugging due to kernel taint
[   42.047716] INFO: 0x8bf2c4a5-0x720c0928. First byte 0x0 instead of 0xcc
[   42.048677] INFO: Slab 0xbc6d2040 objects=29 used=18 fp=0xdc07dec4 flags=0x2808101
[   42.049743] INFO: Object 0xd53a3464 @offset=2528 fp=0xccdcdebb

[   42.050747] Redzone 76f1b237: cc cc cc cc cc cc cc cc                          ........
[   42.051839] Object d53a3464: 6b 6b 6b 6b 6b 6b 6b 6b 0c 00 00 00 6c 00 00 00  kkkkkkkk....l...
[   42.053015] Object f49a30cc: 6c 00 0c 00 00 00 00 00 00 00 00 03 78 a3 15 f6  l...........x...
[   42.054203] Object acfe4220: 20 00 02 00 ff ff ff ff 00 00 00 00 00 00 00 00   ...............
[   42.055370] Object 21024e91: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
[   42.056541] Object 070e04c3: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
[   42.057797] Object 948a777a: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
[   42.059061] Redzone 8bf2c4a5: 00 00 00 00                                      ....
[   42.060189] Padding a681b46e: 5a 5a 5a 5a 5a 5a 5a 5a                          ZZZZZZZZ

Fix by making sure the new buffer is properly resized to contain all the
requested data.

BugLink: https://bugs.launchpad.net/bugs/1813244
Signed-off-by: Andrea Righi <andrea.righi@canonical.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'nfp-fix-retcode-and-disable-netpoll-on-representors'

Jakub Kicinski says:

====================
nfp: fix retcode and disable netpoll on representors

This series avoids a potential crash on nfp representor devices
when netpoll is in use. If transmitting the frame through underlying
vNIC fails we'd return an error code (by passing on error code from
__dev_queue_xmit()) and cause double free in netpoll code.

Fix the error code and disable netpoll on reprs altogether.
IRQ-safety of locking the queues and calling __dev_queue_xmit()
is questionable.

Big thanks to John Hurley for debugging and narrowing down
the trace log after I gave up! :)
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

nfp: disable netpoll on representors

NFP reprs are software device on top of the PF's vNIC.
The comment above __dev_queue_xmit() sayeth:

When calling this method, interrupts MUST be enabled. This is because
the BH enable code must have IRQs enabled so that it will not deadlock.

For netconsole we can't guarantee IRQ state, let's just
disable netpoll on representors to be on the safe side.

When the initial implementation of NFP reprs was added by the
commit 5de73ee46704 ("nfp: general representor implementation")
.ndo_poll_controller was required for netpoll to be enabled.

Fixes: ac3d9dd034e5 ("netpoll: make ndo_poll_controller() optional")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

nfp: validate the return code from dev_queue_xmit()

dev_queue_xmit() may return error codes as well as netdev_tx_t,
and it always consumes the skb. Make sure we always return a
correct netdev_tx_t value.

Fixes: eadfa4c3be99 ("nfp: add stats and xmit helpers for representors")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

netns: provide pure entropy for net_hash_mix()

net_hash_mix() currently uses kernel address of a struct net,
and is used in many places that could be used to reveal this
address to a patient attacker, thus defeating KASLR, for
the typical case (initial net namespace, &init_net is
not dynamically allocated)

I believe the original implementation tried to avoid spending
too many cycles in this function, but security comes first.

Also provide entropy regardless of CONFIG_NET_NS.

Fixes: 0b4419162aa6 ("netns: introduce the net_hash_mix "salt" for hashes")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Amit Klein <aksecurity@gmail.com>
Reported-by: Benny Pinkas <benny@pinkas.net>
Cc: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

qmi_wwan: add Olicard 600

This is a Qualcomm based device with a QMI function on interface 4.
It is mode switched from 2020:2030 using a standard eject message.

T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  6 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=2020 ProdID=2031 Rev= 2.32
S:  Manufacturer=Mobile Connect
S:  Product=Mobile Connect
S:  SerialNumber=0123456789ABCDEF
C:* #Ifs= 6 Cfg#= 1 Atr=80 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E:  Ad=83(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E:  Ad=85(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E:  Ad=87(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=89(I) Atr=03(Int.) MxPS=   8 Ivl=32ms
E:  Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=(none)
E:  Ad=8a(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=125us

Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: Implement flow_dissect callback for tag_qca

Add flow_dissect for qca tagged packet to get the right hash.

Signed-off-by: Xiaofei Shen <xiaofeis@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch '40GbE' of git://git./linux/kernel/git/jkirsher/net-queue

Jeff Kirsher says:

====================
Intel Wired LAN Driver Fixes 2019-03-26

This series contains updates to igb, ixgbe, i40e and fm10k.

Jake fixes an issue with PTP in i40e where a previous commit resulted
in a regression where the driver would interpret small negative
adjustments as large positive additions, resulting in incorrect
behavior.

Arvind Sankar fixes an issue in igb where a previous commit would cause
a warning in the PCI pm core and resulted in pci_pm_runtime_suspend
would not call pci_save_state or pci_finish_runtime_suspend.

Ivan Vecera fixes MDIO bus registration with ixgbe, where the driver was
ignoring errors returned when registering and would leave the pointer in
a NULL state which triggered a BUG when un-registering.

Stefan Assmann fixes the check for Wake-On-LAN for i40e, which only
supports magic packet.

Yue Haibing fixes a potential NULL pointer de-reference in fm10k by
adding a simple check if the value is NULL.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'batadv-net-for-davem-20190328' of git://git.open-mesh.org/linux-merge

Simon Wunderlich says:

====================
Here are some batman-adv bugfixes:

- Fix refcount underflows in bridge loop avoidance code,
by Sven Eckelmann (3 patches)

- Fix warning when CFG80211 isn't enabled, by Anders Roxell

- Fix genl notification for throughput override, by Sven Eckelmann

====================

Signed-off-by: David S. Miller <davem@davemloft.net>

bpf, libbpf: fix quiet install_headers

Both btf.h and xsk.h headers are not installed quietly due to
missing '\' for the call to QUIET_INSTALL. Lets fix it.

Before:

  # make install_headers
    INSTALL  headers
  if [ ! -d '''/usr/local/include/bpf' ]; then install -d -m 755 '''/usr/local/include/bpf'; fi; install btf.h -m 644 '''/usr/local/include/bpf';
  if [ ! -d '''/usr/local/include/bpf' ]; then install -d -m 755 '''/usr/local/include/bpf'; fi; install xsk.h -m 644 '''/usr/local/include/bpf';
  # ls /usr/local/include/bpf/
  bpf.h  btf.h  libbpf.h  xsk.h

After:

  # make install_headers
    INSTALL  headers
  # ls /usr/local/include/bpf/
  bpf.h  btf.h  libbpf.h  xsk.h

Fixes: a493f5f9d8c2 ("libbpf: Install btf.h with libbpf")
Fixes: 379e2014c95b ("libbpf: add xsk.h to install_headers target")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>

libbpf: add libelf dependency to shared library build

The DPDK project is moving forward with its AF_XDP PMD, and during
that process some libbpf issues surfaced [1]: When libbpf was built
as a shared library, libelf was not included in the linking phase.
Since libelf is an internal depedency to libbpf, libelf should be
included. This patch adds '-lelf' to resolve that.

[1] https://patches.dpdk.org/patch/50704/#93571

Fixes: 1b76c13e4b36 ("bpf tools: Introduce 'bpf' library and add bpf feature check")
Suggested-by: Luca Boccassi <bluca@debian.org>
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

libbpf: add xsk.h to install_headers target

The xsk.h header file was missing from the install_headers target in
the Makefile. This patch simply adds xsk.h to the set of installed
headers.

Fixes: 1cad07884239 ("libbpf: add support for using AF_XDP sockets")
Reported-by: Bruce Richardson <bruce.richardson@intel.com>
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

vrf: prevent adding upper devices

VRF devices don't work with upper devices. Currently, it's possible to
add a VRF device to a bridge or team, and to create macvlan, macsec, or
ipvlan devices on top of a VRF (bond and vlan are prevented respectively
by the lack of an ndo_set_mac_address op and the NETIF_F_VLAN_CHALLENGED
feature flag).

Fix this by setting the IFF_NO_RX_HANDLER flag (introduced in commit
f5426250a6ec ("net: introduce IFF_NO_RX_HANDLER")).

Cc: David Ahern <dsahern@gmail.com>
Fixes: 193125dbd8eb ("net: Introduce VRF device driver")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'thunderx-fix-receive-buffer-page-recycling'

Dean Nelson says:

====================
thunderx: fix receive buffer page recycling

In attempting to optimize receive buffer page recycling for XDP, commit
773225388dae15e72790 ("net: thunderx: Optimize page recycling for XDP")
inadvertently introduced two problems for the non-XDP case, that will be
addressed by this patch series.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

thunderx: eliminate extra calls to put_page() for pages held for recycling

For the non-XDP case, commit 773225388dae15e72790 ("net: thunderx: Optimize
page recycling for XDP") added code to nicvf_free_rbdr() that, when releasing
the additional receive buffer page reference held for recycling, repeatedly
calls put_page() until the page's _refcount goes to zero. Which results in
the page being freed.

This is not okay if the page's _refcount was greater than 1 (in the non-XDP
case), because nicvf_free_rbdr() should not be subtracting more than what
nicvf_alloc_page() had previously added to the page's _refcount, which was
only 1 (in the non-XDP case).

This can arise if a received packet is still being processed and the receive
buffer (i.e., skb->head) has not yet been freed via skb_free_head() when
nicvf_free_rbdr() is spinning through the aforementioned put_page() loop.

If this should occur, when the received packet finishes processing and
skb_free_head() is called, various problems can ensue. Exactly what, depends on
whether the page has already been reallocated or not, anything from "BUG: Bad
page state ... ", to "Unable to handle kernel NULL pointer dereference ..." or
"Unable to handle kernel paging request...".

So this patch changes nicvf_free_rbdr() to only call put_page() once for pages
held for recycling (in the non-XDP case).

Fixes: 773225388dae ("net: thunderx: Optimize page recycling for XDP")
Signed-off-by: Dean Nelson <dnelson@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

thunderx: enable page recycling for non-XDP case

Commit 773225388dae15e72790 ("net: thunderx: Optimize page recycling for XDP")
added code to nicvf_alloc_page() that inadvertently disables receive buffer
page recycling for the non-XDP case by always NULL'ng the page pointer.

This patch corrects two if-conditionals to allow for the recycling of non-XDP
mode pages by only setting the page pointer to NULL when the page is not ready
for recycling.

Fixes: 773225388dae ("net: thunderx: Optimize page recycling for XDP")
Signed-off-by: Dean Nelson <dnelson@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: mii: Fix PAUSE cap advertisement from linkmode_adv_to_lcl_adv_t() helper

With a recent link mode advertisement code update this helper
providing local pause capability translation used for flow
control link mode negotiation got broken.
For eth drivers using this helper, the issue is apparent only
if either PAUSE or ASYM_PAUSE is being advertised.

Fixes: 3c1bcc8614db ("net: ethernet: Convert phydev advertize and supported from u32 to link mode")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: fix compile error

Currently, the rules for configuring search paths in Kbuild have
changed, this will lead some erros when compiling hns3 with the
following command:

make O=DIR M=drivers/net/ethernet/hisilicon/hns3

drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_cmd.c:11:10:
fatal error: hnae3.h: No such file or directory

This patch fix it by adding $(srctree)/ prefix to the serach paths.

Signed-off-by: Xi Wang <wangxi11@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ila: Fix rhashtable walker list corruption

ila_xlat_nl_cmd_flush uses rhashtable walkers allocated from the
stack but it never frees them. This corrupts the walker list of
the hash table.

This patch fixes it.

Reported-by: syzbot+dae72a112334aa65a159@syzkaller.appspotmail.com
Fixes: b6e71bdebb12 ("ila: Flush netlink command to clear xlat...")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

MAINTAINERS: Fix documentation file name for PHY Library

MAINTAINERS still pointed to phy.txt after moving this file into the rst
format, fix this.

Reported-by: Joe Perches <joe@perches.com>
Fixes: 25fe02d00a1e ("Documentation: net: phy: switch documentation to rst format")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: datagram: fix unbounded loop in __skb_try_recv_datagram()

Christoph reported a stall while peeking datagram with an offset when
busy polling is enabled. __skb_try_recv_datagram() uses as the loop
termination condition 'queue empty'. When peeking, the socket
queue can be not empty, even when no additional packets are received.

Address the issue explicitly checking for receive queue changes,
as currently done by __skb_wait_for_more_packets().

Fixes: 2b5cd0dfa384 ("net: Change return type of sk_busy_loop from bool to void")
Reported-and-tested-by: Christoph Paasch <cpaasch@apple.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: mv88e6xxx: fix few issues in mv88e6390x_port_set_cmode

This patches fixes few issues in mv88e6390x_port_set_cmode().

1. When entering the function the old cmode may be 0, in this case
   mv88e6390x_serdes_get_lane() returns -ENODEV. As result we bail
   out and have no chance to set a new mode. Therefore deal properly
   with -ENODEV.

2. Once we have disabled power and irq, let's set the cached cmode to 0.
   This reflects the actual status and is cleaner if we bail out with an
   error in the following function calls.

3. The cached cmode is used by mv88e6390x_serdes_get_lane(),
   mv88e6390_serdes_power_lane() and mv88e6390_serdes_irq_enable().
   Currently we set the cached mode to the new one at the very end of
   the function only, means until then we use the old one what may be
   wrong.

4. When calling mv88e6390_serdes_irq_enable() we use the lane value
   belonging to the old cmode. Get the lane belonging to the new cmode
   before calling this function.

It's hard to provide a good "Fixes" tag because quite a few smaller
changes have been done to the code in question recently.

Fixes: d235c48b40d3 ("net: dsa: mv88e6xxx: power serdes on/off for 10G interfaces on 6390X")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge git://git./linux/kernel/git/davem/net

Pull networking fixes from David Miller:
"Fixes here and there, a couple new device IDs, as usual:

   1) Fix BQL race in dpaa2-eth driver, from Ioana Ciornei.

   2) Fix 64-bit division in iwlwifi, from Arnd Bergmann.

   3) Fix documentation for some eBPF helpers, from Quentin Monnet.

   4) Some UAPI bpf header sync with tools, also from Quentin Monnet.

   5) Set descriptor ownership bit at the right time for jumbo frames in
      stmmac driver, from Aaro Koskinen.

   6) Set IFF_UP properly in tun driver, from Eric Dumazet.

   7) Fix load/store doubleword instruction generation in powerpc eBPF
      JIT, from Naveen N. Rao.

   8) nla_nest_start() return value checks all over, from Kangjie Lu.

   9) Fix asoc_id handling in SCTP after the SCTP_*_ASSOC changes this
      merge window. From Marcelo Ricardo Leitner and Xin Long.

  10) Fix memory corruption with large MTUs in stmmac, from Aaro
      Koskinen.

  11) Do not use ipv4 header for ipv6 flows in TCP and DCCP, from Eric
      Dumazet.

  12) Fix topology subscription cancellation in tipc, from Erik Hugne.

  13) Memory leak in genetlink error path, from Yue Haibing.

  14) Valid control actions properly in packet scheduler, from Davide
      Caratti.

  15) Even if we get EEXIST, we still need to rehash if a shrink was
      delayed. From Herbert Xu.

  16) Fix interrupt mask handling in interrupt handler of r8169, from
      Heiner Kallweit.

  17) Fix leak in ehea driver, from Wen Yang"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (168 commits)
  dpaa2-eth: fix race condition with bql frame accounting
  chelsio: use BUG() instead of BUG_ON(1)
  net: devlink: skip info_get op call if it is not defined in dumpit
  net: phy: bcm54xx: Encode link speed and activity into LEDs
  tipc: change to check tipc_own_id to return in tipc_net_stop
  net: usb: aqc111: Extend HWID table by QNAP device
  net: sched: Kconfig: update reference link for PIE
  net: dsa: qca8k: extend slave-bus implementations
  net: dsa: qca8k: remove leftover phy accessors
  dt-bindings: net: dsa: qca8k: support internal mdio-bus
  dt-bindings: net: dsa: qca8k: fix example
  net: phy: don't clear BMCR in genphy_soft_reset
  bpf, libbpf: clarify bump in libbpf version info
  bpf, libbpf: fix version info and add it to shared object
  rxrpc: avoid clang -Wuninitialized warning
  tipc: tipc clang warning
  net: sched: fix cleanup NULL pointer exception in act_mirr
  r8169: fix cable re-plugging issue
  net: ethernet: ti: fix possible object reference leak
  net: ibm: fix possible object reference leak
  ...

Merge branch 'fix-btf_dedup'

Andrii Nakryiko says:

====================
This patch set fixes bug in btf_dedup_is_equiv() check mishandling equivalence
comparison between VOID kind in candidate type graph versus anonymous non-VOID
kind in canonical type graph.

Patch #1 fixes bug, by comparing candidate and canonical kinds for equality,
before proceeding to kind-specific checks.
Patch #2 adds a test case testing this specific scenario.
====================

Signed-off-by: Alexei Starovoitov <ast@kernel.org>

selftests/bpf: add btf_dedup test for VOID equivalence check

This patch adds specific test exposing bug in btf_dedup_is_equiv() when
comparing candidate VOID type to a non-VOID canonical type. It's
important for canonical type to be anonymous, otherwise name equality
check will do the right thing and will exit early.

Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

libbpf: fix btf_dedup equivalence check handling of different kinds

btf_dedup_is_equiv() used to compare btf_type->info fields, before doing
kind-specific equivalence check. This comparsion implicitly verified
that candidate and canonical types are of the same kind. With enum fwd
resolution logic this check couldn't be done generically anymore, as for
enums info contains vlen, which differs between enum fwd and
fully-defined enum, so this check was subsumed by kind-specific
equivalence checks.

This change caused btf_dedup_is_equiv() to let through VOID vs other
types check to reach switch, which was never meant to be handing VOID
kind, as VOID kind is always pre-resolved to itself and is only
equivalent to itself, which is checked early in btf_dedup_is_equiv().

This change adds back BTF kind equality check in place of more generic
btf_type->info check, still defering further kind-specific checks to
a per-kind switch.

Fixes: 9768095ba97c ("btf: resolve enum fwds in btf_dedup")
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

fm10k: Fix a potential NULL pointer dereference

Syzkaller report this:

kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] SMP KASAN PTI
CPU: 0 PID: 4378 Comm: syz-executor.0 Tainted: G         C        5.0.0+ #5
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014
RIP: 0010:__lock_acquire+0x95b/0x3200 kernel/locking/lockdep.c:3573
Code: 00 0f 85 28 1e 00 00 48 81 c4 08 01 00 00 5b 5d 41 5c 41 5d 41 5e 41 5f c3 4c 89 ea 48 b8 00 00 00 00 00 fc ff df 48 c1 ea 03 <80> 3c 02 00 0f 85 cc 24 00 00 49 81 7d 00 e0 de 03 a6 41 bc 00 00
RSP: 0018:ffff8881e3c07a40 EFLAGS: 00010002
RAX: dffffc0000000000 RBX: 0000000000000000 RCX: 0000000000000000
RDX: 0000000000000010 RSI: 0000000000000000 RDI: 0000000000000080
RBP: 0000000000000000 R08: 0000000000000001 R09: 0000000000000000
R10: ffff8881e3c07d98 R11: ffff8881c7f21f80 R12: 0000000000000001
R13: 0000000000000080 R14: 0000000000000000 R15: 0000000000000001
FS:  00007fce2252e700(0000) GS:ffff8881f2400000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fffc7eb0228 CR3: 00000001e5bea002 CR4: 00000000007606f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
PKRU: 55555554
Call Trace:
lock_acquire+0xff/0x2c0 kernel/locking/lockdep.c:4211
__mutex_lock_common kernel/locking/mutex.c:925 [inline]
__mutex_lock+0xdf/0x1050 kernel/locking/mutex.c:1072
drain_workqueue+0x24/0x3f0 kernel/workqueue.c:2934
destroy_workqueue+0x23/0x630 kernel/workqueue.c:4319
__do_sys_delete_module kernel/module.c:1018 [inline]
__se_sys_delete_module kernel/module.c:961 [inline]
__x64_sys_delete_module+0x30c/0x480 kernel/module.c:961
do_syscall_64+0x9f/0x450 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x462e99
Code: f7 d8 64 89 02 b8 ff ff ff ff c3 66 0f 1f 44 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 bc ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007fce2252dc58 EFLAGS: 00000246 ORIG_RAX: 00000000000000b0
RAX: ffffffffffffffda RBX: 000000000073bf00 RCX: 0000000000462e99
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000020000140
RBP: 0000000000000002 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00007fce2252e6bc
R13: 00000000004bcca9 R14: 00000000006f6b48 R15: 00000000ffffffff

If alloc_workqueue fails, it should return -ENOMEM, otherwise may
trigger this NULL pointer dereference while unloading drivers.

Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 0a38c17a21a0 ("fm10k: Remove create_workqueue")
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: fix WoL support check

The current check for WoL on i40e is broken. Code comment says only
magic packet is supported, so only check for that.

Fixes: 540a152da762 (i40e/ixgbe/igb: fail on new WoL flag setting WAKE_MAGICSECURE)
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ixgbe: fix mdio bus registration

The ixgbe ignores errors returned from mdiobus_register() and leaves
adapter->mii_bus non-NULL and MDIO bus state as MDIOBUS_ALLOCATED.
This triggers a BUG from mdiobus_unregister() during ixgbe_remove() call.

Fixes: 8fa10ef01260 ("ixgbe: register a mdiobus")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

igb: Fix WARN_ONCE on runtime suspend

The runtime_suspend device callbacks are not supposed to save
configuration state or change the power state. Commit fb29f76cc566
("igb: Fix an issue that PME is not enabled during runtime suspend")
changed the driver to not save configuration state during runtime
suspend, however the driver callback still put the device into a
low-power state. This causes a warning in the pci pm core and results in
pci_pm_runtime_suspend not calling pci_save_state or pci_finish_runtime_suspend.

Fix this by not changing the power state either, leaving that to pci pm
core, and make the same change for suspend callback as well.

Also move a couple of defines into the appropriate header file instead
of inline in the .c file.

Fixes: fb29f76cc566 ("igb: Fix an issue that PME is not enabled during runtime suspend")
Signed-off-by: Arvind Sankar <niveditas98@gmail.com>
Reviewed-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: fix i40e_ptp_adjtime when given a negative delta

Commit 0ac30ce43323 ("i40e: fix up 32 bit timespec references",
2017-07-26) claims to be cleaning up references to 32-bit timespecs.

The actual contents of the commit make no sense, as it converts a call
to timespec64_add into timespec64_add_ns. This would seem ok, if (a) the
change was documented in the commit message, and (b) timespec64_add_ns
supported negative numbers.

timespec64_add_ns doesn't work with signed deltas, because the
implementation is based around iter_div_u64_rem. This change resulted in
a regression where i40e_ptp_adjtime would interpret small negative
adjustments as large positive additions, resulting in incorrect
behavior.

This commit doesn't appear to fix anything, is not well explained, and
introduces a bug, so lets just revert it.

Reverts: 0ac30ce43323 ("i40e: fix up 32 bit timespec references", 2017-07-26)
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Merge tag 'nfs-for-5.1-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs

Pull NFS client bugfixes from Trond Myklebust:
"Highlights include:

  Stable fixes:
   - Fix nfs4_lock_state refcounting in nfs4_alloc_{lock,unlock}data()
   - fix mount/umount race in nlmclnt.
   - NFSv4.1 don't free interrupted slot on open

  Bugfixes:
   - Don't let RPC_SOFTCONN tasks time out if the transport is connected
   - Fix a typo in nfs_init_timeout_values()
   - Fix layoutstats handling during read failovers
   - fix uninitialized variable warning"

* tag 'nfs-for-5.1-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
  SUNRPC: fix uninitialized variable warning
  pNFS/flexfiles: Fix layoutstats handling during read failovers
  NFS: Fix a typo in nfs_init_timeout_values()
  SUNRPC: Don't let RPC_SOFTCONN tasks time out if the transport is connected
  NFSv4.1 don't free interrupted slot on open
  NFS: fix mount/umount race in nlmclnt.
  NFS: Fix nfs4_lock_state refcounting in nfs4_alloc_{lock,unlock}data()

bpf, doc: fix BTF docs reflow of bullet list

Section 2.2.1 BTF_KIND_INT a bullet list was collapsed due to
text reflow in commit 9ab5305dbe3f ("docs/btf: reflow text to
fill up to 78 characters").

This patch correct the mistake. Also adjust next bullet list,
which is used for comparison, to get rendered the same way.

Fixes: 9ab5305dbe3f ("docs/btf: reflow text to fill up to 78 characters")
Link: https://www.kernel.org/doc/html/latest/bpf/btf.html#btf-kind-int
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

SUNRPC: fix uninitialized variable warning

Avoid following compiler warning on uninitialized variable

net/sunrpc/xprtsock.c: In function ‘xs_read_stream_request.constprop’:
net/sunrpc/xprtsock.c:525:10: warning: ‘read’ may be used uninitialized in this function [-Wmaybe-uninitialized]
   return read;
          ^~~~
net/sunrpc/xprtsock.c:529:23: warning: ‘ret’ may be used uninitialized in this function [-Wmaybe-uninitialized]
  return ret < 0 ? ret : read;
         ~~~~~~~~~~~~~~^~~~~~

Signed-off-by: Alakesh Haloi <alakesh.haloi@gmail.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>

Merge branch 'fix-verifier-warning'

Paul Chaignon says:

====================
The BPF verifier checks the maximum number of call stack frames twice,
first in the main CFG traversal (do_check) and then in a subsequent
traversal (check_max_stack_depth). If the second check fails, it logs a
'verifier bug' warning and errors out, as the number of call stack frames
should have been verified already.

However, the second check may fail without indicating a verifier bug: if
the excessive function calls reside in dead code, the main CFG traversal
may not visit them; the subsequent traversal visits all instructions,
including dead code.

This case raises the question of how invalid dead code should be treated.
The first patch implements the conservative option and rejects such code;
the second adds a test case.
====================

Signed-off-by: Alexei Starovoitov <ast@kernel.org>

selftests/bpf: test case for invalid call stack in dead code

This patch adds a test case with an excessive number of call stack frames
in dead code.

Signed-off-by: Paul Chaignon <paul.chaignon@orange.com>
Tested-by: Xiao Han <xiao.han@orange.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

bpf: remove incorrect 'verifier bug' warning

The BPF verifier checks the maximum number of call stack frames twice,
first in the main CFG traversal (do_check) and then in a subsequent
traversal (check_max_stack_depth). If the second check fails, it logs a
'verifier bug' warning and errors out, as the number of call stack frames
should have been verified already.

However, the second check may fail without indicating a verifier bug: if
the excessive function calls reside in dead code, the main CFG traversal
may not visit them; the subsequent traversal visits all instructions,
including dead code.

This case raises the question of how invalid dead code should be treated.
This patch implements the conservative option and rejects such code.

Signed-off-by: Paul Chaignon <paul.chaignon@orange.com>
Tested-by: Xiao Han <xiao.han@orange.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

dpaa2-eth: fix race condition with bql frame accounting

It might happen that Tx conf acknowledges a frame before it was
subscribed in bql, as subscribing was previously done after the enqueue
operation.

This patch moves the netdev_tx_sent_queue call before the actual frame
enqueue, so that this can never happen.

Fixes: 569dac6a5a0d ("dpaa2-eth: bql support")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

chelsio: use BUG() instead of BUG_ON(1)

clang warns about possible bugs in a dead code branch after
BUG_ON(1) when CONFIG_PROFILE_ALL_BRANCHES is enabled:

drivers/net/ethernet/chelsio/cxgb4/sge.c:479:3: error: variable 'buf_size' is used uninitialized whenever 'if'
      condition is false [-Werror,-Wsometimes-uninitialized]
                BUG_ON(1);
                ^~~~~~~~~
include/asm-generic/bug.h:61:36: note: expanded from macro 'BUG_ON'
#define BUG_ON(condition) do { if (unlikely(condition)) BUG(); } while (0)
                                   ^~~~~~~~~~~~~~~~~~~
include/linux/compiler.h:48:23: note: expanded from macro 'unlikely'
#  define unlikely(x)   (__branch_check__(x, 0, __builtin_constant_p(x)))
                        ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/chelsio/cxgb4/sge.c:482:9: note: uninitialized use occurs here
        return buf_size;
               ^~~~~~~~
drivers/net/ethernet/chelsio/cxgb4/sge.c:479:3: note: remove the 'if' if its condition is always true
                BUG_ON(1);
                ^
include/asm-generic/bug.h:61:32: note: expanded from macro 'BUG_ON'
#define BUG_ON(condition) do { if (unlikely(condition)) BUG(); } while (0)
                               ^
drivers/net/ethernet/chelsio/cxgb4/sge.c:459:14: note: initialize the variable 'buf_size' to silence this warning
        int buf_size;
                    ^
                     = 0

Use BUG() here to create simpler code that clang understands
correctly.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: devlink: skip info_get op call if it is not defined in dumpit

In dumpit, unlike doit, the check for info_get op being defined
is missing. Add it and avoid null pointer dereference in case driver
does not define this op.

Fixes: f9cf22882c60 ("devlink: add device information API")
Reported-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: phy: bcm54xx: Encode link speed and activity into LEDs

Previously the green and amber LEDs on this quad PHY were solid, to
indicate an encoding of the link speed (10/100/1000).

This keeps the LEDs always on just as before, but now they flash on
Rx/Tx activity.

Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: change to check tipc_own_id to return in tipc_net_stop

When running a syz script, a panic occurred:

[  156.088228] BUG: KASAN: use-after-free in tipc_disc_timeout+0x9c9/0xb20 [tipc]
[  156.094315] Call Trace:
[  156.094844]  <IRQ>
[  156.095306]  dump_stack+0x7c/0xc0
[  156.097346]  print_address_description+0x65/0x22e
[  156.100445]  kasan_report.cold.3+0x37/0x7a
[  156.102402]  tipc_disc_timeout+0x9c9/0xb20 [tipc]
[  156.106517]  call_timer_fn+0x19a/0x610
[  156.112749]  run_timer_softirq+0xb51/0x1090

It was caused by the netns freed without deleting the discoverer timer,
while later on the netns would be accessed in the timer handler.

The timer should have been deleted by tipc_net_stop() when cleaning up a
netns. However, tipc has been able to enable a bearer and start d->timer
without the local node_addr set since Commit 52dfae5c85a4 ("tipc: obtain
node identity from interface by default"), which caused the timer not to
be deleted in tipc_net_stop() then.

So fix it in tipc_net_stop() by changing to check local node_id instead
of local node_addr, as Jon suggested.

While at it, remove the calling of tipc_nametbl_withdraw() there, since
tipc_nametbl_stop() will take of the nametbl's freeing after.

Fixes: 52dfae5c85a4 ("tipc: obtain node identity from interface by default")
Reported-by: syzbot+a25307ad099309f1c2b9@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: usb: aqc111: Extend HWID table by QNAP device

New device of QNAP based on aqc111u
Add this ID to blacklist of cdc_ether driver as well

Signed-off-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: sched: Kconfig: update reference link for PIE

RFC 8033 replaces the IETF draft for PIE

Signed-off-by: Leslie Monis <lesliemonis@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: qca8k: extend slave-bus implementations

This patch implements accessors for the QCA8337 MDIO access
through the MDIO_MASTER register, which makes it possible to
access the PHYs on slave-bus through the switch. In cases
where the switch ports are already mapped via external
"phy-phandles", the internal mdio-bus is disabled in order to
prevent a duplicated discovery and enumeration of the same
PHYs. Don't use mixed external and internal mdio-bus
configurations, as this is not supported by the hardware.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: qca8k: remove leftover phy accessors

This belated patch implements Andrew Lunn's request of
"remove the phy_read() and phy_write() functions."
<https://lore.kernel.org/patchwork/comment/902734/>

While seemingly harmless, this causes the switch's user
port PHYs to get registered twice. This is because the
DSA subsystem will create a slave mdio-bus not knowing
that the qca8k_phy_(read|write) accessors operate on
the external mdio-bus. So the same "bus" gets effectively
duplicated.

Cc: stable@vger.kernel.org
Fixes: 6b93fb46480a ("net-next: dsa: add new driver for qca8xxx family")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

dt-bindings: net: dsa: qca8k: support internal mdio-bus

This patch updates the qca8k's binding to document to the
approach for using the internal mdio-bus of the supported
qca8k switches.

Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

dt-bindings: net: dsa: qca8k: fix example

In the example, the phy at phy@0 is clashing with
the switch0@0 at the same address. Usually, the switches
are accessible through pseudo PHYs which in case of the
qca8k are located at 0x10 - 0x18.

Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'for-5.1-rc2-tag' of git://git./linux/kernel/git/kdave/linux

Pull btrfs fixes from David Sterba:

- fsync fixes: i_size for truncate vs fsync, dio vs buffered during
   snapshotting, remove complicated but incomplete assertion

- removed excessive warnigs, misreported device stats updates

- fix raid56 page mapping for 32bit arch

- fixes reported by static analyzer

* tag 'for-5.1-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  Btrfs: fix assertion failure on fsync with NO_HOLES enabled
  btrfs: Avoid possible qgroup_rsv_size overflow in btrfs_calculate_inode_block_rsv_size
  btrfs: Fix bound checking in qgroup_trace_new_subtree_blocks
  btrfs: raid56: properly unmap parity page in finish_parity_scrub()
  btrfs: don't report readahead errors and don't update statistics
  Btrfs: fix file corruption after snapshotting due to mix of buffered/DIO writes
  btrfs: remove WARN_ON in log_dir_items
  Btrfs: fix incorrect file size after shrinking truncate and fsync

Merge tag 'trace-v5.1-rc2' of git://git./linux/kernel/git/rostedt/linux-trace

Pull tracing fixes from Steven Rostedt:
"Three small fixes:

   - A fix to a double free in the histogram code

   - Uninitialized variable fix

   - Use NULL instead of zero fix and spelling fixes"

* tag 'trace-v5.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  ftrace: Fix warning using plain integer as NULL & spelling corrections
  tracing: initialize variable in create_dyn_event()
  tracing: Remove unnecessary var_ref destroy in track_data_destroy()

Merge tag 'locks-v5.1' of git://git./linux/kernel/git/jlayton/linux

Pull file locking bugfix from Jeff Layton:
"Just a single fix for a bug that crept into POSIX lock deadlock
detection in v5.0"

* tag 'locks-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/jlayton/linux:
locks: wake any locks blocked on request before deadlock check

ftrace: Fix warning using plain integer as NULL & spelling corrections

Changed 0 --> NULL to avoid sparse warning
Corrected spelling mistakes reported by checkpatch.pl
Sparse warning below:

sudo make C=2 CF=-D__CHECK_ENDIAN__ M=kernel/trace

CHECK kernel/trace/ftrace.c
kernel/trace/ftrace.c:3007:24: warning: Using plain integer as NULL pointer
kernel/trace/ftrace.c:4758:37: warning: Using plain integer as NULL pointer

Link: http://lkml.kernel.org/r/20190323183523.GA2244@hari-Inspiron-1545
Signed-off-by: Hariprasad Kelam <hariprasad.kelam@gmail.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>

tracing: initialize variable in create_dyn_event()

Fix compile warning in create_dyn_event(): 'ret' may be used uninitialized
in this function [-Wuninitialized].

Link: http://lkml.kernel.org/r/1553237900-8555-1-git-send-email-frowand.list@gmail.com
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Tom Zanussi <tom.zanussi@linux.intel.com>
Cc: Ravi Bangoria <ravi.bangoria@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org
Fixes: 5448d44c3855 ("tracing: Add unified dynamic event framework")
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>

tracing: Remove unnecessary var_ref destroy in track_data_destroy()

Commit 656fe2ba85e8 (tracing: Use hist trigger's var_ref array to
destroy var_refs) centralized the destruction of all the var_refs
in one place so that other code didn't have to do it.

The track_data_destroy() added later ignored that and also destroyed
the track_data var_ref, causing a double-free error flagged by KASAN.

==================================================================
BUG: KASAN: use-after-free in destroy_hist_field+0x30/0x70
Read of size 8 at addr ffff888086df2210 by task bash/1694

CPU: 6 PID: 1694 Comm: bash Not tainted 5.1.0-rc1-test+ #15
Hardware name: Hewlett-Packard HP Compaq Pro 6300 SFF/339A, BIOS K01 v03.03
07/14/2016
Call Trace:
dump_stack+0x71/0xa0
? destroy_hist_field+0x30/0x70
print_address_description.cold.3+0x9/0x1fb
? destroy_hist_field+0x30/0x70
? destroy_hist_field+0x30/0x70
kasan_report.cold.4+0x1a/0x33
? __kasan_slab_free+0x100/0x150
? destroy_hist_field+0x30/0x70
destroy_hist_field+0x30/0x70
track_data_destroy+0x55/0xe0
destroy_hist_data+0x1f0/0x350
hist_unreg_all+0x203/0x220
event_trigger_open+0xbb/0x130
do_dentry_open+0x296/0x700
? stacktrace_count_trigger+0x30/0x30
? generic_permission+0x56/0x200
? __x64_sys_fchdir+0xd0/0xd0
? inode_permission+0x55/0x200
? security_inode_permission+0x18/0x60
path_openat+0x633/0x22b0
? path_lookupat.isra.50+0x420/0x420
? __kasan_kmalloc.constprop.12+0xc1/0xd0
? kmem_cache_alloc+0xe5/0x260
? getname_flags+0x6c/0x2a0
? do_sys_open+0x149/0x2b0
? do_syscall_64+0x73/0x1b0
? entry_SYSCALL_64_after_hwframe+0x44/0xa9
? _raw_write_lock_bh+0xe0/0xe0
? __kernel_text_address+0xe/0x30
? unwind_get_return_address+0x2f/0x50
? __list_add_valid+0x2d/0x70
? deactivate_slab.isra.62+0x1f4/0x5a0
? getname_flags+0x6c/0x2a0
? set_track+0x76/0x120
do_filp_open+0x11a/0x1a0
? may_open_dev+0x50/0x50
? _raw_spin_lock+0x7a/0xd0
? _raw_write_lock_bh+0xe0/0xe0
? __alloc_fd+0x10f/0x200
do_sys_open+0x1db/0x2b0
? filp_open+0x50/0x50
do_syscall_64+0x73/0x1b0
entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x7fa7b24a4ca2
Code: 25 00 00 41 00 3d 00 00 41 00 74 4c 48 8d 05 85 7a 0d 00 8b 00 85 c0
75 6d 89 f2 b8 01 01 00 00 48 89 fe bf 9c ff ff ff 0f 05 <48> 3d 00 f0 ff ff
0f 87 a2 00 00 00 48 8b 4c 24 28 64 48 33 0c 25
RSP: 002b:00007fffbafb3af0 EFLAGS: 00000246 ORIG_RAX: 0000000000000101
RAX: ffffffffffffffda RBX: 000055d3648ade30 RCX: 00007fa7b24a4ca2
RDX: 0000000000000241 RSI: 000055d364a55240 RDI: 00000000ffffff9c
RBP: 00007fffbafb3bf0 R08: 0000000000000020 R09: 0000000000000002
R10: 00000000000001b6 R11: 0000000000000246 R12: 0000000000000000
R13: 0000000000000003 R14: 0000000000000001 R15: 000055d364a55240
==================================================================

So remove the track_data_destroy() destroy_hist_field() call for that
var_ref.

Link: http://lkml.kernel.org/r/1deffec420f6a16d11dd8647318d34a66d1989a9.camel@linux.intel.com
Fixes: 466f4528fbc69 ("tracing: Generalize hist trigger onmax and save action")
Reported-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Tom Zanussi <tom.zanussi@linux.intel.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>

bpf: fix use after free in bpf_evict_inode

syzkaller was able to generate the following UAF in bpf:

  BUG: KASAN: use-after-free in lookup_last fs/namei.c:2269 [inline]
  BUG: KASAN: use-after-free in path_lookupat.isra.43+0x9f8/0xc00 fs/namei.c:2318
  Read of size 1 at addr ffff8801c4865c47 by task syz-executor2/9423

  CPU: 0 PID: 9423 Comm: syz-executor2 Not tainted 4.20.0-rc1-next-20181109+
  #110
  Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
  Google 01/01/2011
  Call Trace:
    __dump_stack lib/dump_stack.c:77 [inline]
    dump_stack+0x244/0x39d lib/dump_stack.c:113
    print_address_description.cold.7+0x9/0x1ff mm/kasan/report.c:256
    kasan_report_error mm/kasan/report.c:354 [inline]
    kasan_report.cold.8+0x242/0x309 mm/kasan/report.c:412
    __asan_report_load1_noabort+0x14/0x20 mm/kasan/report.c:430
    lookup_last fs/namei.c:2269 [inline]
    path_lookupat.isra.43+0x9f8/0xc00 fs/namei.c:2318
    filename_lookup+0x26a/0x520 fs/namei.c:2348
    user_path_at_empty+0x40/0x50 fs/namei.c:2608
    user_path include/linux/namei.h:62 [inline]
    do_mount+0x180/0x1ff0 fs/namespace.c:2980
    ksys_mount+0x12d/0x140 fs/namespace.c:3258
    __do_sys_mount fs/namespace.c:3272 [inline]
    __se_sys_mount fs/namespace.c:3269 [inline]
    __x64_sys_mount+0xbe/0x150 fs/namespace.c:3269
    do_syscall_64+0x1b9/0x820 arch/x86/entry/common.c:290
    entry_SYSCALL_64_after_hwframe+0x49/0xbe
  RIP: 0033:0x457569
  Code: fd b3 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7
  48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff
  ff 0f 83 cb b3 fb ff c3 66 2e 0f 1f 84 00 00 00 00
  RSP: 002b:00007fde6ed96c78 EFLAGS: 00000246 ORIG_RAX: 00000000000000a5
  RAX: ffffffffffffffda RBX: 0000000000000005 RCX: 0000000000457569
  RDX: 0000000020000040 RSI: 0000000020000000 RDI: 0000000000000000
  RBP: 000000000072bf00 R08: 0000000020000340 R09: 0000000000000000
  R10: 0000000000200000 R11: 0000000000000246 R12: 00007fde6ed976d4
  R13: 00000000004c2c24 R14: 00000000004d4990 R15: 00000000ffffffff

  Allocated by task 9424:
    save_stack+0x43/0xd0 mm/kasan/kasan.c:448
    set_track mm/kasan/kasan.c:460 [inline]
    kasan_kmalloc+0xc7/0xe0 mm/kasan/kasan.c:553
    __do_kmalloc mm/slab.c:3722 [inline]
    __kmalloc_track_caller+0x157/0x760 mm/slab.c:3737
    kstrdup+0x39/0x70 mm/util.c:49
    bpf_symlink+0x26/0x140 kernel/bpf/inode.c:356
    vfs_symlink+0x37a/0x5d0 fs/namei.c:4127
    do_symlinkat+0x242/0x2d0 fs/namei.c:4154
    __do_sys_symlink fs/namei.c:4173 [inline]
    __se_sys_symlink fs/namei.c:4171 [inline]
    __x64_sys_symlink+0x59/0x80 fs/namei.c:4171
    do_syscall_64+0x1b9/0x820 arch/x86/entry/common.c:290
    entry_SYSCALL_64_after_hwframe+0x49/0xbe

  Freed by task 9425:
    save_stack+0x43/0xd0 mm/kasan/kasan.c:448
    set_track mm/kasan/kasan.c:460 [inline]
    __kasan_slab_free+0x102/0x150 mm/kasan/kasan.c:521
    kasan_slab_free+0xe/0x10 mm/kasan/kasan.c:528
    __cache_free mm/slab.c:3498 [inline]
    kfree+0xcf/0x230 mm/slab.c:3817
    bpf_evict_inode+0x11f/0x150 kernel/bpf/inode.c:565
    evict+0x4b9/0x980 fs/inode.c:558
    iput_final fs/inode.c:1550 [inline]
    iput+0x674/0xa90 fs/inode.c:1576
    do_unlinkat+0x733/0xa30 fs/namei.c:4069
    __do_sys_unlink fs/namei.c:4110 [inline]
    __se_sys_unlink fs/namei.c:4108 [inline]
    __x64_sys_unlink+0x42/0x50 fs/namei.c:4108
    do_syscall_64+0x1b9/0x820 arch/x86/entry/common.c:290
    entry_SYSCALL_64_after_hwframe+0x49/0xbe

In this scenario path lookup under RCU is racing with the final
unlink in case of symlinks. As Linus puts it in his analysis:

  [...] We actually RCU-delay the inode freeing itself, but
  when we do the final iput(), the "evict()" function is called
  synchronously. Now, the simple fix would seem to just RCU-delay
  the kfree() of the symlink data in bpf_evict_inode(). Maybe
  that's the right thing to do. [...]

Al suggested to piggy-back on the ->destroy_inode() callback in
order to implement RCU deferral there which can then kfree() the
inode->i_link eventually right before putting inode back into
inode cache. By reusing free_inode_nonrcu() from there we can
avoid the need for our own inode cache and just reuse generic
one as we currently do.

And in-fact on top of all this we should just get rid of the
bpf_evict_inode() entirely. This means truncate_inode_pages_final()
and clear_inode() will then simply be called by the fs core via
evict(). Dropping the reference should really only be done when
inode is unhashed and nothing reachable anymore, so it's better
also moved into the final ->destroy_inode() callback.

Fixes: 0f98621bef5d ("bpf, inode: add support for symlinks and fix mtime/ctime")
Reported-by: syzbot+fb731ca573367b7f6564@syzkaller.appspotmail.com
Reported-by: syzbot+a13e5ead792d6df37818@syzkaller.appspotmail.com
Reported-by: syzbot+7a8ba368b47fdefca61e@syzkaller.appspotmail.com
Suggested-by: Al Viro <viro@zeniv.linux.org.uk>
Analyzed-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Link: https://lore.kernel.org/lkml/0000000000006946d2057bbd0eef@google.com/T/

net: phy: don't clear BMCR in genphy_soft_reset

So far we effectively clear the BMCR register. Some PHY's can deal
with this (e.g. because they reset BMCR to a default as part of a
soft-reset) whilst on others this causes issues because e.g. the
autoneg bit is cleared. Marvell is an example, see also thread [0].
So let's be a little bit more gentle and leave all bits we're not
interested in as-is. This change is needed for PHY drivers to
properly deal with the original patch.

[0] https://marc.info/?t=155264050700001&r=1&w=2

Fixes: 6e2d85ec0559 ("net: phy: Stop with excessive soft reset")
Tested-by: Phil Reid <preid@electromag.com.au>
Tested-by: liweihang <liweihang@hisilicon.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Revert "parport: daisy: use new parport device model"

This reverts commit 1aec4211204d9463d1fd209eb50453de16254599.

Steven Rostedt reports that it causes a hang at bootup and bisected it
to this commit.

The troigger is apparently a module alias for "parport_lowlevel" that
points to "parport_pc", which causes a hang with

    modprobe -q -- parport_lowlevel

blocking forever with a backtrace like this:

    wait_for_completion_killable+0x1c/0x28
    call_usermodehelper_exec+0xa7/0x108
    __request_module+0x351/0x3d8
    get_lowlevel_driver+0x28/0x41 [parport]
    __parport_register_driver+0x39/0x1f4 [parport]
    daisy_drv_init+0x31/0x4f [parport]
    parport_bus_init+0x5d/0x7b [parport]
    parport_default_proc_register+0x26/0x1000 [parport]
    do_one_initcall+0xc2/0x1e0
    do_init_module+0x50/0x1d4
    load_module+0x1c2e/0x21b3
    sys_init_module+0xef/0x117

Supid says:
"Due to the new device model daisy driver will now try to find the
  parallel ports while trying to register its driver so that it can bind
  with them. Now, since daisy driver is loaded while parport bus is
  initialising the list of parport is still empty and it tries to load
  the lowlevel driver, which has an alias set to parport_pc, now causes
  a deadlock"

But I don't think the daisy driver should be loaded by the parport
initialization in the first place, so let's revert the whole change.

If the daisy driver can just initialize separately on its own (like a
driver should), instead of hooking into the parport init sequence
directly, this issue probably would go away.

Reported-and-bisected-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Reported-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

locks: wake any locks blocked on request before deadlock check

Andreas reported that he was seeing the tdbtorture test fail in some
cases with -EDEADLCK when it wasn't before. Some debugging showed that
deadlock detection was sometimes discovering the caller's lock request
itself in a dependency chain.

While we remove the request from the blocked_lock_hash prior to
reattempting to acquire it, any locks that are blocked on that request
will still be present in the hash and will still have their fl_blocker
pointer set to the current request.

This causes posix_locks_deadlock to find a deadlock dependency chain
when it shouldn't, as a lock request cannot block itself.

We are going to end up waking all of those blocked locks anyway when we
go to reinsert the request back into the blocked_lock_hash, so just do
it prior to checking for deadlocks. This ensures that any lock blocked
on the current request will no longer be part of any blocked request
chain.

URL: https://bugzilla.kernel.org/show_bug.cgi?id=202975
Fixes: 5946c4319ebb ("fs/locks: allow a lock request to block other requests.")
Cc: stable@vger.kernel.org
Reported-by: Andreas Schneider <asn@redhat.com>
Signed-off-by: Neil Brown <neilb@suse.com>
Signed-off-by: Jeff Layton <jlayton@kernel.org>

batman-adv: Fix genl notification for throughput_override

The throughput_override sysfs file is not below the meshif but below a
hardif. The kobj has therefore not a pointer which can be used to find the
batadv_priv data. The pointer stored in the hardif object must be used
instead to find the correct meshif private data.

Fixes: 7e6f461efe25 ("batman-adv: Trigger genl notification on sysfs config change")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>

batman-adv: fix warning in function batadv_v_elp_get_throughput

When CONFIG_CFG80211 isn't enabled the compiler correcly warns about
'sinfo.pertid' may be unused. It can also happen for other error
conditions that it not warn about.

net/batman-adv/bat_v_elp.c: In function ‘batadv_v_elp_get_throughput.isra.0’:
include/net/cfg80211.h:6370:13: warning: ‘sinfo.pertid’ may be used
uninitialized in this function [-Wmaybe-uninitialized]
kfree(sinfo->pertid);
~~~~~^~~~~~~~

Rework so that we only release '&sinfo' if cfg80211_get_station returns
zero.

Fixes: 7d652669b61d ("batman-adv: release station info tidstats")
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>

batman-adv: Reduce tt_global hash refcnt only for removed entry

The batadv_hash_remove is a function which searches the hashtable for an
entry using a needle, a hashtable bucket selection function and a compare
function. It will lock the bucket list and delete an entry when the compare
function matches it with the needle. It returns the pointer to the
hlist_node which matches or NULL when no entry matches the needle.

The batadv_tt_global_free is not itself protected in anyway to avoid that
any other function is modifying the hashtable between the search for the
entry and the call to batadv_hash_remove. It can therefore happen that the
entry either doesn't exist anymore or an entry was deleted which is not the
same object as the needle. In such an situation, the reference counter (for
the reference stored in the hashtable) must not be reduced for the needle.
Instead the reference counter of the actually removed entry has to be
reduced.

Otherwise the reference counter will underflow and the object might be
freed before all its references were dropped. The kref helpers reported
this problem as:

refcount_t: underflow; use-after-free.

Fixes: 7683fdc1e886 ("batman-adv: protect the local and the global trans-tables with rcu")
Reported-by: Martin Weinelt <martin@linuxlounge.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>

batman-adv: Reduce tt_local hash refcnt only for removed entry

The batadv_hash_remove is a function which searches the hashtable for an
entry using a needle, a hashtable bucket selection function and a compare
function. It will lock the bucket list and delete an entry when the compare
function matches it with the needle. It returns the pointer to the
hlist_node which matches or NULL when no entry matches the needle.

The batadv_tt_local_remove is not itself protected in anyway to avoid that
any other function is modifying the hashtable between the search for the
entry and the call to batadv_hash_remove. It can therefore happen that the
entry either doesn't exist anymore or an entry was deleted which is not the
same object as the needle. In such an situation, the reference counter (for
the reference stored in the hashtable) must not be reduced for the needle.
Instead the reference counter of the actually removed entry has to be
reduced.

Otherwise the reference counter will underflow and the object might be
freed before all its references were dropped. The kref helpers reported
this problem as:

refcount_t: underflow; use-after-free.

Fixes: ef72706a0543 ("batman-adv: protect tt_local_entry from concurrent delete events")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>

batman-adv: Reduce claim hash refcnt only for removed entry

The batadv_hash_remove is a function which searches the hashtable for an
entry using a needle, a hashtable bucket selection function and a compare
function. It will lock the bucket list and delete an entry when the compare
function matches it with the needle. It returns the pointer to the
hlist_node which matches or NULL when no entry matches the needle.

The batadv_bla_del_claim is not itself protected in anyway to avoid that
any other function is modifying the hashtable between the search for the
entry and the call to batadv_hash_remove. It can therefore happen that the
entry either doesn't exist anymore or an entry was deleted which is not the
same object as the needle. In such an situation, the reference counter (for
the reference stored in the hashtable) must not be reduced for the needle.
Instead the reference counter of the actually removed entry has to be
reduced.

Otherwise the reference counter will underflow and the object might be
freed before all its references were dropped. The kref helpers reported
this problem as:

refcount_t: underflow; use-after-free.

Fixes: 23721387c409 ("batman-adv: add basic bridge loop avoidance code")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>

Merge git://git./pub/scm/linux/kernel/git/bpf/bpf

Alexei Starovoitov says:

====================
pull-request: bpf 2019-03-24

The following pull-request contains BPF updates for your *net* tree.

The main changes are:

1) libbpf verision fix up from Daniel.

2) fix liveness propagation from Jakub.

3) fix verbose print of refcounted regs from Martin.

4) fix for large map allocations from Martynas.

5) fix use after free in sanitize_ptr_alu from Xu.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'libbpf-fixup'

Daniel Borkmann says:

====================
First one is fixing version in Makefile and shared object and
second one clarifies bump in version. Thanks!

v1 -> v2:
- Fix up soname, thanks Stanislav!
====================

Signed-off-by: Alexei Starovoitov <ast@kernel.org>

bpf, libbpf: clarify bump in libbpf version info

The current documentation suggests that we would need to bump the
libbpf version on every change. Lets clarify this a bit more and
reflect what we do today in practice, that is, bumping it once per
development cycle.

Fixes: 76d1b894c515 ("libbpf: Document API and ABI conventions")
Reported-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

bpf, libbpf: fix version info and add it to shared object

Even though libbpf's versioning script for the linker (libbpf.map)
is pointing to 0.0.2, the BPF_EXTRAVERSION in the Makefile has
not been updated along with it and is therefore still on 0.0.1.

While fixing up, I also noticed that the generated shared object
versioning information is missing, typical convention is to have
a linker name (libbpf.so), soname (libbpf.so.0) and real name
(libbpf.so.0.0.2) for library management. This is based upon the
LIBBPF_VERSION as well.

The build will then produce the following bpf libraries:

  # ll libbpf*
  libbpf.a
  libbpf.so -> libbpf.so.0.0.2
  libbpf.so.0 -> libbpf.so.0.0.2
  libbpf.so.0.0.2

  # readelf -d libbpf.so.0.0.2 | grep SONAME
  0x000000000000000e (SONAME)             Library soname: [libbpf.so.0]

And install them accordingly:

  # rm -rf /tmp/bld; mkdir /tmp/bld; make -j$(nproc) O=/tmp/bld install

  Auto-detecting system features:
  ...                        libelf: [ on  ]
  ...                           bpf: [ on  ]

    CC       /tmp/bld/libbpf.o
    CC       /tmp/bld/bpf.o
    CC       /tmp/bld/nlattr.o
    CC       /tmp/bld/btf.o
    CC       /tmp/bld/libbpf_errno.o
    CC       /tmp/bld/str_error.o
    CC       /tmp/bld/netlink.o
    CC       /tmp/bld/bpf_prog_linfo.o
    CC       /tmp/bld/libbpf_probes.o
    CC       /tmp/bld/xsk.o
    LD       /tmp/bld/libbpf-in.o
    LINK     /tmp/bld/libbpf.a
    LINK     /tmp/bld/libbpf.so.0.0.2
    LINK     /tmp/bld/test_libbpf
    INSTALL  /tmp/bld/libbpf.a
    INSTALL  /tmp/bld/libbpf.so.0.0.2

  # ll /usr/local/lib64/libbpf.*
  /usr/local/lib64/libbpf.a
  /usr/local/lib64/libbpf.so -> libbpf.so.0.0.2
  /usr/local/lib64/libbpf.so.0 -> libbpf.so.0.0.2
  /usr/local/lib64/libbpf.so.0.0.2

Fixes: 1bf4b05810fe ("tools: bpftool: add probes for eBPF program types")
Fixes: 1b76c13e4b36 ("bpf tools: Introduce 'bpf' library and add bpf feature check")
Reported-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

Linux 5.1-rc2