Merge tag 'for-3.4' of git://openrisc.net/jonas/linux

Pull OpenRISC changes for 3.4 from Jonas Bonn:
 "This series for the OpenRISC architecture consists of mostly trivial
  fixups.  The most interesting bits of the series are:

  * A fix to the timer code whereby the shortest trigger period is set
    to 100 cycles; previously, it was possible to set this to 1 cycle,
    but by the time the register was written, that time had already
    passed and the timer interrupt would not go off until the cycle
    counter had gone a full cycle.

  * Allowing a device tree binary to be passed in to the kernel from
    u-boot.  The OpenRISC architecture has been recently merged into
    upstream u-boot, so this change gets OpenRISC Linux into sync with
    that project."

* tag 'for-3.4' of git://openrisc.net/jonas/linux:
  OpenRISC: Remove memory_start/end prototypes
  openrisc: remove semicolon from KSTK_ defs
  openrisc: sanitize use of orig_gpr11
  openrisc: fix virt_addr_valid
  OpenRISC: Export dump_stack()
  OpenRISC: Select GENERIC_ATOMIC64
  openrisc: Set shortest clock event to 100 ticks
  openrisc: included linux/thread_info.h twice
  OpenRISC: Use set_current_blocked() and block_sigmask()
  OpenRISC: Don't mask signals if we fail to setup signal stack
  OpenRISC: No need to reset handler if SA_ONESHOT
  OpenRISC: Don't reimplement force_sigsegv()
  openrisc: enable passing of flattened device tree pointer
  arch/openrisc/mm/init.c: trivial: use BUG_ON

Merge tag 'ia64-for-linus' of git://git./linux/kernel/git/aegl/linux

Pull miscellaneous Itanium patches from Tony Luck.

The conflicts in arch/ia64/hp/sim/simserial.c were due to patches to
simserial that had alredy been included (with lots of further cleanups)
in the serial tree.

* tag 'ia64-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux:
  Documentation/kernel-parameters: remove inttest parameter
  [IA64] Fix ISA IRQ trigger model and polarity setting
  [IA64] Fix a couple of warnings for EXPORT_SYMBOL
  [IA64] Check return from device_register() in cx_device_register()
  [IA64] Fix warning from machine_kexec.c
  [IA64] simserial, bail out when request_irq fails
  [IA64] hpsim, initialize chip for assigned irqs
  [IA64] simserial, include some headers
  [IA64] hpsim, fix SAL handling in fw-emu
  [IA64] genirq fixup for SGI/SN
  [IA64] disable interrupts when exiting from ia64_mca_cmc_int_handler()

Merge branch 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/tip

Pull additional x86 fixes from Peter Anvin:
 - address a long-standing bug related to when a kernel-spawned process
   gets a signal on an i386 kernel compiled without CONFIG_VM86.

 - fix the newly introduced build warning in arch/x86/boot.

 - fix a typo in the i386 system call table which affects building some
   libcs.

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86-32: Fix endless loop when processing signals for kernel tasks
  x86, boot: Correct CFLAGS for hostprogs
  x86-32: Fix typo for mq_getsetattr in syscall table

Merge branch 'akpm' (Andrew's patch-bomb)

Merge second batch of patches from Andrew Morton:
 - various misc things
 - core kernel changes to prctl, exit, exec, init, etc.
 - kernel/watchdog.c updates
 - get_maintainer
 - MAINTAINERS
 - the backlight driver queue
 - core bitops code cleanups
 - the led driver queue
 - some core prio_tree work
 - checkpatch udpates
 - largeish crc32 update
 - a new poll() feature for the v4l guys
 - the rtc driver queue
 - fatfs
 - ptrace
 - signals
 - kmod/usermodehelper updates
 - coredump
 - procfs updates

* emailed from Andrew Morton <akpm@linux-foundation.org>: (141 commits)
  seq_file: add seq_set_overflow(), seq_overflow()
  proc-ns: use d_set_d_op() API to set dentry ops in proc_ns_instantiate().
  procfs: speed up /proc/pid/stat, statm
  procfs: add num_to_str() to speed up /proc/stat
  proc: speed up /proc/stat handling
  fs/proc/kcore.c: make get_sparsemem_vmemmap_info() static
  coredump: add VM_NODUMP, MADV_NODUMP, MADV_CLEAR_NODUMP
  coredump: remove VM_ALWAYSDUMP flag
  kmod: make __request_module() killable
  kmod: introduce call_modprobe() helper
  usermodehelper: ____call_usermodehelper() doesn't need do_exit()
  usermodehelper: kill umh_wait, renumber UMH_* constants
  usermodehelper: implement UMH_KILLABLE
  usermodehelper: introduce umh_complete(sub_info)
  usermodehelper: use UMH_WAIT_PROC consistently
  signal: zap_pid_ns_processes: s/SEND_SIG_NOINFO/SEND_SIG_FORCED/
  signal: oom_kill_task: use SEND_SIG_FORCED instead of force_sig()
  signal: cosmetic, s/from_ancestor_ns/force/ in prepare_signal() paths
  signal: give SEND_SIG_FORCED more power to beat SIGNAL_UNKILLABLE
  Hexagon: use set_current_blocked() and block_sigmask()
  ...

seq_file: add seq_set_overflow(), seq_overflow()

It is undocumented but a seq_file's overflow state is indicated by
m->count == m->size.  Add seq_set_overflow() and seq_overflow() to
set/check overflow status explicitly.

Based on an idea from Eric Dumazet.

[akpm@linux-foundation.org: tweak code comment]
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

proc-ns: use d_set_d_op() API to set dentry ops in proc_ns_instantiate().

The namespace cleanup path leaks a dentry which holds a reference count
on a network namespace.  Keeping that network namespace from being freed
when the last user goes away.  Leaving things like vlan devices in the
leaked network namespace.

If you use ip netns add for much real work this problem becomes apparent
pretty quickly.  It light testing the problem hides because frequently
you simply don't notice the leak.

Use d_set_d_op() so that DCACHE_OP_* flags are set correctly.

This issue exists back to 3.0.

Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Reported-by: Justin Pettit <jpettit@nicira.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Cc: David Miller <davem@davemloft.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

procfs: speed up /proc/pid/stat, statm

Process accounting applications as top, ps visit some files under
/proc/<pid>.  With seq_put_decimal_ull(), we can optimize /proc/<pid>/stat
and /proc/<pid>/statm files.

This patch adds
  - seq_put_decimal_ll() for signed values.
  - allow delimiter == 0.
  - convert seq_printf() to seq_put_decimal_ull/ll in /proc/stat, statm.

Test result on a system with 2000+ procs.

Before patch:
  [kamezawa@bluextal test]$ top -b -n 1 | wc -l
  2223
  [kamezawa@bluextal test]$ time top -b -n 1 > /dev/null

  real    0m0.675s
  user    0m0.044s
  sys     0m0.121s

  [kamezawa@bluextal test]$ time ps -elf > /dev/null

  real    0m0.236s
  user    0m0.056s
  sys     0m0.176s

After patch:
  kamezawa@bluextal ~]$ time top -b -n 1 > /dev/null

  real    0m0.657s
  user    0m0.052s
  sys     0m0.100s

  [kamezawa@bluextal ~]$ time ps -elf > /dev/null

  real    0m0.198s
  user    0m0.050s
  sys     0m0.145s

Considering top, ps tend to scan /proc periodically, this will reduce cpu
consumption by top/ps to some extent.

[akpm@linux-foundation.org: checkpatch fixes]
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

procfs: add num_to_str() to speed up /proc/stat

== stat_check.py
num = 0
with open("/proc/stat") as f:
        while num < 1000 :
                data = f.read()
                f.seek(0, 0)
                num = num + 1
==

perf shows

    20.39%  stat_check.py  [kernel.kallsyms]    [k] format_decode
    13.41%  stat_check.py  [kernel.kallsyms]    [k] number
    12.61%  stat_check.py  [kernel.kallsyms]    [k] vsnprintf
    10.85%  stat_check.py  [kernel.kallsyms]    [k] memcpy
     4.85%  stat_check.py  [kernel.kallsyms]    [k] radix_tree_lookup
     4.43%  stat_check.py  [kernel.kallsyms]    [k] seq_printf

This patch removes most of calls to vsnprintf() by adding num_to_str()
and seq_print_decimal_ull(), which prints decimal numbers without rich
functions provided by printf().

On my 8cpu box.
== Before patch ==
[root@bluextal test]# time ./stat_check.py

real    0m0.150s
user    0m0.026s
sys     0m0.121s

== After patch ==
[root@bluextal test]# time ./stat_check.py

real    0m0.055s
user    0m0.022s
sys     0m0.030s

[akpm@linux-foundation.org: remove incorrect comment, use less statck in num_to_str(), move comment from .h to .c, simplify seq_put_decimal_ull()]
[andrea@betterlinux.com: avoid breaking the ABI in /proc/stat]
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrea Righi <andrea@betterlinux.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Glauber Costa <glommer@parallels.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Paul Turner <pjt@google.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

proc: speed up /proc/stat handling

On a typical 16 cpus machine, "cat /proc/stat" gives more than 4096 bytes,
and is slow :

  # strace -T -o /tmp/STRACE cat /proc/stat | wc -c
  5826
  # grep "cpu " /tmp/STRACE
  read(0, "cpu  1949310 19 2144714 12117253"..., 32768) = 5826 <0.001504>

Thats partly because show_stat() must be called twice since initial
buffer size is too small (4096 bytes for less than 32 possible cpus)

Fix this by :

 1) Taking into account nr_irqs in the initial buffer sizing.

 2) Using ksize() to allow better filling of initial buffer.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Glauber Costa <glommer@parallels.com>
Cc: Russell King - ARM Linux <linux@arm.linux.org.uk>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Paul Turner <pjt@google.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs/proc/kcore.c: make get_sparsemem_vmemmap_info() static

get_sparsemem_vmemmap_info() is only used inside fs/proc/kcore.c

Signed-off-by: Djalal Harouni <tixxdz@opendz.org>
Reviewed-by: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

coredump: add VM_NODUMP, MADV_NODUMP, MADV_CLEAR_NODUMP

Since we no longer need the VM_ALWAYSDUMP flag, let's use the freed bit
for 'VM_NODUMP' flag.  The idea is is to add a new madvise() flag:
MADV_DONTDUMP, which can be set by applications to specifically request
memory regions which should not dump core.

The specific application I have in mind is qemu: we can add a flag there
that wouldn't dump all of guest memory when qemu dumps core.  This flag
might also be useful for security sensitive apps that want to absolutely
make sure that parts of memory are not dumped.  To clear the flag use:
MADV_DODUMP.

[akpm@linux-foundation.org: s/MADV_NODUMP/MADV_DONTDUMP/, s/MADV_CLEAR_NODUMP/MADV_DODUMP/, per Roland]
[akpm@linux-foundation.org: fix up the architectures which broke]
Signed-off-by: Jason Baron <jbaron@redhat.com>
Acked-by: Roland McGrath <roland@hack.frob.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Avi Kivity <avi@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

coredump: remove VM_ALWAYSDUMP flag

The motivation for this patchset was that I was looking at a way for a
qemu-kvm process, to exclude the guest memory from its core dump, which
can be quite large.  There are already a number of filter flags in
/proc/<pid>/coredump_filter, however, these allow one to specify 'types'
of kernel memory, not specific address ranges (which is needed in this
case).

Since there are no more vma flags available, the first patch eliminates
the need for the 'VM_ALWAYSDUMP' flag.  The flag is used internally by
the kernel to mark vdso and vsyscall pages.  However, it is simple
enough to check if a vma covers a vdso or vsyscall page without the need
for this flag.

The second patch then replaces the 'VM_ALWAYSDUMP' flag with a new
'VM_NODUMP' flag, which can be set by userspace using new madvise flags:
'MADV_DONTDUMP', and unset via 'MADV_DODUMP'.  The core dump filters
continue to work the same as before unless 'MADV_DONTDUMP' is set on the
region.

The qemu code which implements this features is at:

  http://people.redhat.com/~jbaron/qemu-dump/qemu-dump.patch

In my testing the qemu core dump shrunk from 383MB -> 13MB with this
patch.

I also believe that the 'MADV_DONTDUMP' flag might be useful for
security sensitive apps, which might want to select which areas are
dumped.

This patch:

The VM_ALWAYSDUMP flag is currently used by the coredump code to
indicate that a vma is part of a vsyscall or vdso section.  However, we
can determine if a vma is in one these sections by checking it against
the gate_vma and checking for a non-NULL return value from
arch_vma_name().  Thus, freeing a valuable vma bit.

Signed-off-by: Jason Baron <jbaron@redhat.com>
Acked-by: Roland McGrath <roland@hack.frob.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Avi Kivity <avi@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kmod: make __request_module() killable

As Tetsuo Handa pointed out, request_module() can stress the system
while the oom-killed caller sleeps in TASK_UNINTERRUPTIBLE.

The task T uses "almost all" memory, then it does something which
triggers request_module().  Say, it can simply call sys_socket().  This
in turn needs more memory and leads to OOM.  oom-killer correctly
chooses T and kills it, but this can't help because it sleeps in
TASK_UNINTERRUPTIBLE and after that oom-killer becomes "disabled" by the
TIF_MEMDIE task T.

Make __request_module() killable.  The only necessary change is that
call_modprobe() should kmalloc argv and module_name, they can't live in
the stack if we use UMH_KILLABLE.  This memory is freed via
call_usermodehelper_freeinfo()->cleanup.

Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Tejun Heo <tj@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kmod: introduce call_modprobe() helper

No functional changes.  Move the call_usermodehelper code from
__request_module() into the new simple helper, call_modprobe().

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Tejun Heo <tj@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

usermodehelper: ____call_usermodehelper() doesn't need do_exit()

Minor cleanup.  ____call_usermodehelper() can simply return, no need to
call do_exit() explicitely.

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Tejun Heo <tj@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

usermodehelper: kill umh_wait, renumber UMH_* constants

No functional changes.  It is not sane to use UMH_KILLABLE with enum
umh_wait, but obviously we do not want another argument in
call_usermodehelper_* helpers.  Kill this enum, use the plain int.

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Tejun Heo <tj@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

usermodehelper: implement UMH_KILLABLE

Implement UMH_KILLABLE, should be used along with UMH_WAIT_EXEC/PROC.
The caller must ensure that subprocess_info->path/etc can not go away
until call_usermodehelper_freeinfo().

call_usermodehelper_exec(UMH_KILLABLE) does
wait_for_completion_killable.  If it fails, it uses
xchg(&sub_info->complete, NULL) to serialize with umh_complete() which
does the same xhcg() to access sub_info->complete.

If call_usermodehelper_exec wins, it can safely return.  umh_complete()
should get NULL and call call_usermodehelper_freeinfo().

Otherwise we know that umh_complete() was already called, in this case
call_usermodehelper_exec() falls back to wait_for_completion() which
should succeed "very soon".

Note: UMH_NO_WAIT == -1 but it obviously should not be used with
UMH_KILLABLE.  We delay the neccessary cleanup to simplify the back
porting.

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Tejun Heo <tj@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

usermodehelper: introduce umh_complete(sub_info)

Preparation.  Add the new trivial helper, umh_complete().  Currently it
simply does complete(sub_info->complete).

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Tejun Heo <tj@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

usermodehelper: use UMH_WAIT_PROC consistently

A few call_usermodehelper() callers use the hardcoded constant instead of
the proper UMH_WAIT_PROC, fix them.

Reported-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Lars Ellenberg <drbd-dev@lists.linbit.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Michal Januszewski <spock@gentoo.org>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Kentaro Takeda <takedakn@nttdata.co.jp>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: James Morris <jmorris@namei.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

signal: zap_pid_ns_processes: s/SEND_SIG_NOINFO/SEND_SIG_FORCED/

Change zap_pid_ns_processes() to use SEND_SIG_FORCED, it looks more
clear compared to SEND_SIG_NOINFO which relies on from_ancestor_ns logic
send_signal().

It is also more efficient if we need to kill a lot of tasks because it
doesn't alloc sigqueue.

While at it, add the __fatal_signal_pending(task) check as a minor
optimization.

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Anton Vorontsov <anton.vorontsov@linaro.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@gmail.com>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

signal: oom_kill_task: use SEND_SIG_FORCED instead of force_sig()

Change oom_kill_task() to use do_send_sig_info(SEND_SIG_FORCED) instead
of force_sig(SIGKILL).  With the recent changes we do not need force_ to
kill the CLONE_NEWPID tasks.

And this is more correct.  force_sig() can race with the exiting thread
even if oom_kill_task() checks p->mm != NULL, while
do_send_sig_info(group => true) kille the whole process.

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Anton Vorontsov <anton.vorontsov@linaro.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@gmail.com>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

signal: cosmetic, s/from_ancestor_ns/force/ in prepare_signal() paths

Cosmetic, rename the from_ancestor_ns argument in prepare_signal()
paths.  After the previous change it doesn't match the reality.

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Anton Vorontsov <anton.vorontsov@linaro.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@gmail.com>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

signal: give SEND_SIG_FORCED more power to beat SIGNAL_UNKILLABLE

force_sig_info() and friends have the special semantics for synchronous
signals, this interface should not be used if the target is not current.
And it needs the fixes, in particular the clearing of SIGNAL_UNKILLABLE
is not exactly right.

However there are callers which have to use force_ exactly because it
clears SIGNAL_UNKILLABLE and thus it can kill the CLONE_NEWPID tasks,
although this is almost always is wrong by various reasons.

With this patch SEND_SIG_FORCED ignores SIGNAL_UNKILLABLE, like we do if
the signal comes from the ancestor namespace.

This makes the naming in prepare_signal() paths insane, fixed by the
next cleanup.

Note: this only affects SIGKILL/SIGSTOP, but this is enough for
force_sig() abusers.

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Anton Vorontsov <anton.vorontsov@linaro.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@gmail.com>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Hexagon: use set_current_blocked() and block_sigmask()

As described in e6fa16ab9c1e ("signal: sigprocmask() should do
retarget_shared_pending()") the modification of current->blocked is
incorrect as we need to check whether the signal we're about to block is
pending in the shared queue.

Also, use the new helper function introduced in commit 5e6292c0f28f
("signal: add block_sigmask() for adding sigmask to current->blocked")
which centralises the code for updating current->blocked after
successfully delivering a signal and reduces the amount of duplicate
code across architectures.  In the past some architectures got this code
wrong, so using this helper function should stop that from happening
again.

Acked-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Richard Kuo <rkuo@codeaurora.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ptrace: remove PTRACE_SEIZE_DEVEL bit

PTRACE_SEIZE code is tested and ready for production use, remove the
code which requires special bit in data argument to make PTRACE_SEIZE
work.

Strace team prepares for a new release of strace, and we would like to
ship the code which uses PTRACE_SEIZE, preferably after this change goes
into released kernel.

Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Cc: Pedro Alves <palves@redhat.com>
Cc: Jan Kratochvil <jan.kratochvil@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ptrace: renumber PTRACE_EVENT_STOP so that future new options and events can match

PTRACE_EVENT_foo and PTRACE_O_TRACEfoo used to match.

New PTRACE_EVENT_STOP is the first event which has no corresponding
PTRACE_O_TRACE option.  If we will ever want to add another such option,
its PTRACE_EVENT's value will collide with PTRACE_EVENT_STOP's value.

This patch changes PTRACE_EVENT_STOP value to prevent this.

While at it, added a comment - the one atop PTRACE_EVENT block, saying
"Wait extended result codes for the above trace options", is not true
for PTRACE_EVENT_STOP.

Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Cc: Tejun Heo <tj@kernel.org>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Cc: Pedro Alves <palves@redhat.com>
Cc: Jan Kratochvil <jan.kratochvil@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ptrace: make PTRACE_SEIZE set ptrace options specified in 'data' parameter

This can be used to close a few corner cases in strace where we get
unwanted racy behavior after attach, but before we have a chance to set
options (the notorious post-execve SIGTRAP comes to mind), and removes
the need to track "did we set opts for this task" state in strace
internals.

While we are at it:

Make it possible to extend SEIZE in the future with more functionality
by passing non-zero 'addr' parameter.  To that end, error out if 'addr'
is non-zero.  PTRACE_ATTACH did not (and still does not) have such
check, and users (strace) do pass garbage there...  let's avoid
repeating this mistake with SEIZE.

Set all task->ptrace bits in one operation - before this change, we were
adding PT_SEIZED and PT_PTRACE_CAP with task->ptrace |= BIT ops.  This
was probably ok (not a bug), but let's be on a safer side.

Changes since v2: use (unsigned long) casts instead of (long) ones, move
PTRACE_SEIZE_DEVEL-related code to separate lines of code.

Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: Pedro Alves <palves@redhat.com>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Cc: Jan Kratochvil <jan.kratochvil@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ptrace: simplify PTRACE_foo constants and PTRACE_SETOPTIONS code

Exchange PT_TRACESYSGOOD and PT_PTRACE_CAP bit positions, which makes
PT_option bits contiguous and therefore makes code in
ptrace_setoptions() much simpler.

Every PTRACE_O_TRACEevent is defined to (1 << PTRACE_EVENT_event)
instead of using explicit numeric constants, to ensure we don't mess up
relationship between bit positions and event ids.

PT_EVENT_FLAG_SHIFT was not particularly useful, PT_OPT_FLAG_SHIFT with
value of PT_EVENT_FLAG_SHIFT-1 is easier to use.

PT_TRACE_MASK constant is nuked, the only its use is replaced by
(PTRACE_O_MASK << PT_OPT_FLAG_SHIFT).

Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Cc: Pedro Alves <palves@redhat.com>
Cc: Jan Kratochvil <jan.kratochvil@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ptrace: don't modify flags on PTRACE_SETOPTIONS failure

On ptrace(PTRACE_SETOPTIONS, pid, 0, <opts>), we used to set those
option bits which are known, and then fail with -EINVAL if there are
some unknown bits in <opts>.

This is inconsistent with typical error handling, which does not change
any state if input is invalid.

This patch changes PTRACE_SETOPTIONS behavior so that in this case, we
return -EINVAL and don't change any bits in task->ptrace.

It's very unlikely that there is userspace code in the wild which will
be affected by this change: it should have the form

    ptrace(PTRACE_SETOPTIONS, pid, 0, PTRACE_O_BOGUSOPT)

where PTRACE_O_BOGUSOPT is a constant unknown to the kernel.  But kernel
headers, naturally, don't contain any PTRACE_O_BOGUSOPTs, thus the only
way userspace can use one if it defines one itself.  I can't see why
anyone would do such a thing deliberately.

Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Cc: Pedro Alves <palves@redhat.com>
Cc: Jan Kratochvil <jan.kratochvil@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ptrace: don't send SIGTRAP on exec if SEIZED

ptrace_event(PTRACE_EVENT_EXEC) sends SIGTRAP if PT_TRACE_EXEC is not
set.  This is because this SIGTRAP predates PTRACE_O_TRACEEXEC option,
we do not need/want this with PT_SEIZED which can set the options during
attach.

Suggested-by: Pedro Alves <palves@redhat.com>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Chris Evans <scarybeasts@gmail.com>
Cc: Indan Zupancic <indan@nul.nu>
Cc: Denys Vlasenko <vda.linux@googlemail.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Pedro Alves <palves@redhat.com>
Cc: Jan Kratochvil <jan.kratochvil@redhat.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ptrace: the killed tracee should not enter the syscall

Another old/known problem.  If the tracee is killed after it reports
syscall_entry, it starts the syscall and debugger can't control this.
This confuses the users and this creates the security problems for
ptrace jailers.

Change tracehook_report_syscall_entry() to return non-zero if killed,
this instructs syscall_trace_enter() to abort the syscall.

Reported-by: Chris Evans <scarybeasts@gmail.com>
Tested-by: Indan Zupancic <indan@nul.nu>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Denys Vlasenko <vda.linux@googlemail.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Pedro Alves <palves@redhat.com>
Cc: Jan Kratochvil <jan.kratochvil@redhat.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fat: fix bug in enforcing Long File Name length

Since '*outlen' is initialized to zero, it is currently possible to
create a filename of length (FAT_LFN_LEN + 1) when utf8 is not enabled.
To enforce the FAT_LFN_LEN limit, we must perform one less iteration.

Signed-off-by: Namjae Jeon <linkinjeon@gmail.com>
Signed-off-by: Ravishankar N <cyberax82@gmail.com>
Acked-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fat: clean up xlate_to_uni()

xlate_to_uni() is called by vfat_build_slots() with sbi->nls_io as the
final argument.  nls_io can never be null at this point because the
check is already being done in fat_fill_super() wherein the mount fails
if it is null.

Signed-off-by: Namjae Jeon <linkinjeon@gmail.com>
Signed-off-by: Ravishankar N <cyberax82@gmail.com>
Acked-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rtc: ds1307: generalise ram size and offset

Generalise NVRAM to support RAM with other size and offset, such as the
64 bytes of SRAM on the mcp7941x.

[rdunlap@xenotime.net: fix printk format warning]
Signed-off-by: Austin Boyle <Austin.Boyle@aviatnet.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: David Anders <danders.dev@gmail.com>
Cc: Alessandro Zummo <alessandro.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rtc: ds1307: comment and format cleanup

Do some cleanup of the comment sections as well as correct some
formatting issues reported by checkpatch.pl.

Signed-off-by: David Anders <x0132446@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Austin Boyle <Austin.Boyle@aviatnet.com>
Cc: Alessandro Zummo <alessandro.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rtc: ds1307: simplify irq setup code

No need to have two seperate if-blocks for setting up the irq.

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Tested-by: David Anders <danders.dev@gmail.com>
Cc: Austin Boyle <Austin.Boyle@aviatnet.com>
Cc: Alessandro Zummo <alessandro.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rtc: ds1307: refactor chip_desc table

The chip_desc table is suboptimal.  Currently it requires an entry for
every new chip type, even if it is empty.  This has already been
forgotten for the ds1388.  Refactor the code, so new entries are only
needed, when they chip type really needs a (non-empty) description.
Also make the table visually more appealing.

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Austin Boyle <Austin.Boyle@aviatnet.com>
Cc: David Anders <danders.dev@gmail.com>
Cc: Alessandro Zummo <alessandro.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rtc: driver for DA9052/53 PMIC v1

RTC Driver for Dialog Semiconductor DA9052/53 PMICs.

This patch is functionally tested on Samsung SMDKV6410.

[akpm@linux-foundation.org: clean up file header layout, remove unneeded initialisation of local arrays]
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Ashish Jangam <ashish.jangam@kpitcummins.com>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Cc: David Dajun Chen <dchen@diasemi.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc/rtc-max8925.c: fix alarm->enabled mistake in max8925_rtc_read_alarm/max8925_rtc_set_alarm

max8925_rtc_read_alarm() should set alrm->enabled based on both
ALARM_IRQ_MASK and ALARM_CTRL setting.  max8925_rtc_set_alarm() should
enable/disable alarm according to ALARM_CTRL reg setting.

Signed-off-by: Kevin Liu <kliu5@marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc/rtc-max8925.c: fix max8925_rtc_read_alarm() return value error

max8925_rtc_read_alarm should always return 0 with success

Signed-off-by: Kevin Liu <kliu5@marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc/rtc-pm8xxx.c: make pm8xxx_rtc_pm_ops static

Signed-off-by: Navin P <zicrim@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc: remove IRQF_DISABLED

Since commit e58aa3d2d0cc ("genirq: run irq handlers with interrupts
disabled") we run all interrupt handlers with interrupts disabled and we
even check and yell when an interrupt handler returns with interrupts
enabled - see commit b738a50a2026 ("genirq: warn when handler enables
interrupts").

So now this flag is a NOOP and can be removed.

Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Wan ZongShun <mcuos.com@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc/rtc-twl.c: return correct RTC event from ISR

Following changes are made as part of this change:

1. As TWL RTC supports periodic interrupt, the correct event should be
   RTC_PF instead of RTC_UF.

2. No need to initialize variable "events" to 0 & then OR it with the
   event values.  Hence fixing it.

Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc/rtc-twl.c: simplify RTC interrupt clearing

For clearing RTC interrupt, programming ALARM bit only is sufficient, as
all other bits are any way not affected by writing 0 to them.

Hence removed unwanted OR operation.

Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc/rtc-twl.c: enable RTC irrespective of its prior state

As part of probe, before enabling RTC, RTC_CTRL register is read to check
if it is already running.  If RTC is used by kernel alone, then this read
is not required.  Even if RTC was enabled already by boot loader, setting
STOP_RTC bit again should not harm.  Hence removed unwanted read
operation.

Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc/rtc-twl.c: optimize IRQ bit access

As the TWL RTC driver has a cached copy of enabled RTC interrupt bits in
variable rtc_irq_bits, that can be checked before really setting or
masking any of the interrupt bits.

Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

MIPS: add RTC support for loongson1B

Add RTC support(TOY counter0) for loongson1B SOC

Signed-off-by: zhao zhang <zhzhl555@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rtc: convert rtc i2c drivers to module_i2c_driver

Factor out some boilerplate code for i2c driver registration into
module_i2c_driver.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Piotr Ziecik <kosmo@semihalf.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Srikanth Srinivasan <srikanth.srinivasan@freescale.com>
Cc: Mike Rapoport <mike@compulab.co.il>
Cc: Sergey Lapin <slapin@ossfans.org>
Cc: Roman Fietze <roman.fietze@telemotive.de>
Cc: Herbert Valerio Riedel <hvr@gnu.org>
Cc: Alexander Bigga <ab@mycable.de>
Cc: Dale Farnsworth <dale@farnsworth.org>
Cc: Gregory Hermant <gregory.hermant@calao-systems.com>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Martyn Welch <martyn.welch@ge.com>
Cc: Byron Bradley <byron.bbradley@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rtc: convert rtc spi drivers to module_spi_driver

Factor out some boilerplate code for spi driver registration into
module_spi_driver.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Mark Jackson <mpfj@mimc.co.uk>
Cc: Dennis Aberilla <denzzzhome@yahoo.com>
Cc: Nikolaus Voss <n.voss@weinmann.de>
Cc: "Kim B. Heino" <Kim.Heino@bluegiga.com>
Cc: Raphael Assenat <raph@raphnet.net>
Cc: Chris Verges <chrisv@cyberswitching.com>
Cc: Magnus Damm <damm@opensource.se>
Cc: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rtc/rtc-spear: call platform_set_drvdata() before registering rtc device

rtc_device_register() calls rtc-spear routines internally.  These
routines call dev_get_drvdata() to get struct spear_rtc_config.
Currently, platform_set_drvdata is called after rtc device is
registered.  This causes system to crash, as dev_get_drvdata returns
NULL.

For this we need to call platform_set_drvdata() before registering rtc
device.  This requires further cleanup, that leads to removal of
dev_set_drvdata on rtc->dev, which was just not required at all.

Also, we change the parameter to request_irq and pass pointer to config
instead of pointer to rtc struct.

This patch brings all above changes.

Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Cc: Deepak Sikri <deepak.sikri@st.com>
Acked-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rtc/spear: fix for RTC_AIE_ON and RTC_AIE_OFF ioctl errors

Define API for '.alarm_irq_enable' to enable and disable alarm irq. This
is required by the framework else RTC_AIE_ON and RTC_AIE_OFF ioctls
return errors.

Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Cc: Deepak Sikri <deepak.sikri@st.com>
Acked-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rtc-spear: fix for balancing the enable_irq_wake in Power Mgmt

Handle the fix for unbalanced irq for the cases when enable_irq_wake
fails, and a warning related to same is displayed on the console.  The
workaround is handled at the driver level.

Signed-off-by: Deepak Sikri <deepak.sikri@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

init/do_mounts.c: print error code on mount failure

Printing the error code makes it easier to debug the cause of a mount
failure.  For example I had the problem that the root file system could
not be mounted read-writeable because my SD card was write-protected.
Without an error code it looks like the SD card was not detected at all.

Signed-off-by: Bernhard Walle <bernhard@bwalle.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

init: check printed flag to skip printing message

Otherwise the 'Calibration skipped' message gets printed everytime a CPU
is hotplugged in, cluttering console for systems that frequently hotplug
CPUs.

Signed-off-by: Diwakar Tundlam <dtundlam@nvidia.com>
Cc: Phil Carmody <ext-phil.2.carmody@nokia.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Greg KH <greg@kroah.com>
Cc: Sameer Nanda <snanda@chromium.org>
Cc: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

epoll: remove unneeded variable in reverse_path_check()

We never use the length variable.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

epoll: comment the funky #ifdef

Looking for a bug in -rt, I stumbled across this code here from: commit
2dfa4eeab0fc ("epoll keyed wakeups: teach epoll about hints coming with
the wakeup key"), specifically:

  #ifdef CONFIG_DEBUG_LOCK_ALLOC
  static inline void ep_wake_up_nested(wait_queue_head_t *wqueue,
                                      unsigned long events, int subclass)
  {
         unsigned long flags;

         spin_lock_irqsave_nested(&wqueue->lock, flags, subclass);
         wake_up_locked_poll(wqueue, events);
         spin_unlock_irqrestore(&wqueue->lock, flags);
  }
  #else
  static inline void ep_wake_up_nested(wait_queue_head_t *wqueue,
                                      unsigned long events, int subclass)
  {
         wake_up_poll(wqueue, events);
  }
  #endif

You change the function of ep_wake_up_nested() depending on whether
CONFIG_DEBUG_LOCK_ALLOC is set or not.  This looks awfully suspicious,
and there's no comment to explain why.  I initially thought that this
was trying to fool lockdep, and hiding a real bug.

Investigating it, I found the creation of wake_up_nested() (which no
longer exists) but was created for the sole purpose of epoll and its
strange wake ups, as explained in commit 0ccf831cbee9 ("lockdep:
annotate epoll")

Although the commit message says "annotate epoll" the change log is much
better at explaining what is happening than what is in the actual code.
Thus a comment is really necessary here.  And to save the time of other
developers from having to go trudging through the git logs trying to
figure out why this code exists.

I took parts of the change log and placed it into a comment above the
affected code.  This will make the description of what is happening more
visible to new developers that have to look at this code for the first
time.

Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Davide Libenzi <davidel@xmailserver.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

poll: add poll_requested_events() and poll_does_not_wait() functions

In some cases the poll() implementation in a driver has to do different
things depending on the events the caller wants to poll for.  An example
is when a driver needs to start a DMA engine if the caller polls for
POLLIN, but doesn't want to do that if POLLIN is not requested but instead
only POLLOUT or POLLPRI is requested.  This is something that can happen
in the video4linux subsystem among others.

Unfortunately, the current epoll/poll/select implementation doesn't
provide that information reliably.  The poll_table_struct does have it: it
has a key field with the event mask.  But once a poll() call matches one
or more bits of that mask any following poll() calls are passed a NULL
poll_table pointer.

Also, the eventpoll implementation always left the key field at ~0 instead
of using the requested events mask.

This was changed in eventpoll.c so the key field now contains the actual
events that should be polled for as set by the caller.

The solution to the NULL poll_table pointer is to set the qproc field to
NULL in poll_table once poll() matches the events, not the poll_table
pointer itself.  That way drivers can obtain the mask through a new
poll_requested_events inline.

The poll_table_struct can still be NULL since some kernel code calls it
internally (netfs_state_poll() in ./drivers/staging/pohmelfs/netfs.h).  In
that case poll_requested_events() returns ~0 (i.e.  all events).

Very rarely drivers might want to know whether poll_wait will actually
wait.  If another earlier file descriptor in the set already matched the
events the caller wanted to wait for, then the kernel will return from the
select() call without waiting.  This might be useful information in order
to avoid doing expensive work.

A new helper function poll_does_not_wait() is added that drivers can use
to detect this situation.  This is now used in sock_poll_wait() in
include/net/sock.h.  This was the only place in the kernel that needed
this information.

Drivers should no longer access any of the poll_table internals, but use
the poll_requested_events() and poll_does_not_wait() access functions
instead.  In order to enforce that the poll_table fields are now prepended
with an underscore and a comment was added warning against using them
directly.

This required a change in unix_dgram_poll() in unix/af_unix.c which used
the key field to get the requested events.  It's been replaced by a call
to poll_requested_events().

For qproc it was especially important to change its name since the
behavior of that field changes with this patch since this function pointer
can now be NULL when that wasn't possible in the past.

Any driver accessing the qproc or key fields directly will now fail to compile.

Some notes regarding the correctness of this patch: the driver's poll()
function is called with a 'struct poll_table_struct *wait' argument.  This
pointer may or may not be NULL, drivers can never rely on it being one or
the other as that depends on whether or not an earlier file descriptor in
the select()'s fdset matched the requested events.

There are only three things a driver can do with the wait argument:

1) obtain the key field:

events = wait ? wait->key : ~0;

   This will still work although it should be replaced with the new
   poll_requested_events() function (which does exactly the same).
   This will now even work better, since wait is no longer set to NULL
   unnecessarily.

2) use the qproc callback. This could be deadly since qproc can now be
   NULL. Renaming qproc should prevent this from happening. There are no
   kernel drivers that actually access this callback directly, BTW.

3) test whether wait == NULL to determine whether poll would return without
   waiting. This is no longer sufficient as the correct test is now
   wait == NULL || wait->_qproc == NULL.

   However, the worst that can happen here is a slight performance hit in
   the case where wait != NULL and wait->_qproc == NULL. In that case the
   driver will assume that poll_wait() will actually add the fd to the set
   of waiting file descriptors. Of course, poll_wait() will not do that
   since it tests for wait->_qproc. This will not break anything, though.

   There is only one place in the whole kernel where this happens
   (sock_poll_wait() in include/net/sock.h) and that code will be replaced
   by a call to poll_does_not_wait() in the next patch.

   Note that even if wait->_qproc != NULL drivers cannot rely on poll_wait()
   actually waiting. The next file descriptor from the set might match the
   event mask and thus any possible waits will never happen.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Jonathan Corbet <corbet@lwn.net>
Reviewed-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Davide Libenzi <davidel@xmailserver.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

crc32: select an algorithm via Kconfig

Allow the kernel builder to choose a crc32* algorithm for the kernel.

Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: Bob Pearson <rpearson@systemfabricworks.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

crc32: add self-test code for crc32c

Add self-test code for crc32c.

Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: Bob Pearson <rpearson@systemfabricworks.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

crypto: crc32c should use library implementation

Since lib/crc32.c now provides crc32c, remove the software implementation
here and call the library function instead.

Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Bob Pearson <rpearson@systemfabricworks.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

crc32: bolt on crc32c

Reuse the existing crc32 code to stamp out a crc32c implementation.

Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Bob Pearson <rpearson@systemfabricworks.com>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

crc32: add note about this patchset to crc32.c

Add a comment at the top of crc32.c

[djwong@us.ibm.com: Minor changelog tweaks]
Signed-off-by: Bob Pearson <rpearson@systemfabricworks.com>
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

crc32: optimize loop counter for x86

Add two changes that improve the performance of x86 systems

1. replace main loop with incrementing counter this change improves
   the performance of the selftest by about 5-6% on Nehalem CPUs.  The
   apparent reason is that the compiler can use the loop index to perform
   an indexed memory access.  This is reported to make the performance of
   PowerPC CPUs to get worse.

2. replace the rem_len loop with incrementing counter this change
   improves the performance of the selftest, which has more than the usual
   number of occurances, by about 1-2% on x86 CPUs.  In actual work loads
   the length is most often a multiple of 4 bytes and this code does not
   get executed as often if at all.  Again this change is reported to make
   the performance of PowerPC get worse.

[djwong@us.ibm.com: Minor changelog tweaks]
Signed-off-by: Bob Pearson <rpearson@systemfabricworks.com>
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

crc32: add slice-by-8 algorithm to existing code

Add slicing-by-8 algorithm to the existing slicing-by-4 algorithm.  This
consists of:

- extend largest BITS size from 32 to 64
- extend tables from tab[4][256] to up to tab[8][256]
- Add code for inner loop.

[djwong@us.ibm.com: Minor changelog tweaks]
Signed-off-by: Bob Pearson <rpearson@systemfabricworks.com>
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

crc32: make CRC_*_BITS definition correspond to actual bit counts

crc32.c provides a choice of one of several algorithms for computing the
LSB and LSB versions of the CRC32 checksum based on the parameters
CRC_LE_BITS and CRC_BE_BITS.

In the original version the values 1, 2, 4 and 8 respectively selected
versions of the alrogithm that computed the crc 1, 2, 4 and 32 bits as a
time.

This patch series adds a new version that computes the CRC 64 bits at a
time.  To make things easier to understand the parameter has been
reinterpreted to actually stand for the number of bits processed in each
step of the algorithm so that the old value 8 has been replaced with the
value 32.

This also allows us to add in a widely used crc algorithm that computes
the crc 8 bits at a time called the Sarwate algorithm.

[djwong@us.ibm.com: Minor changelog tweaks]
Signed-off-by: Bob Pearson <rpearson@systemfabricworks.com>
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

crc32: fix mixing of endian-specific types

crc32.c in its original version freely mixed u32, __le32 and __be32 types
which caused warnings from sparse with __CHECK_ENDIAN__.  This patch fixes
these by forcing the types to u32.

[djwong@us.ibm.com: Minor changelog tweaks]
Signed-off-by: Bob Pearson <rpearson@systemfabricworks.com>
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

crc32: miscellaneous cleanups

Misc cleanup of lib/crc32.c and related files.

- remove unnecessary header files.

- straighten out some convoluted ifdef's

- rewrite some references to 2 dimensional arrays as 1 dimensional
  arrays to make them correct.  I.e.  replace tab[i] with tab[0][i].

- a few trivial whitespace changes

- fix a warning in gen_crc32tables.c caused by a mismatch in the type of
  the pointer passed to output table.  Since the table is only used at
  kernel compile time, it is simpler to make the table big enough to hold
  the largest column size used.  One cannot make the column size smaller
  in output_table because it has to be used by both the le and be tables
  and they can have different column sizes.

[djwong@us.ibm.com: Minor changelog tweaks]
Signed-off-by: Bob Pearson <rpearson@systemfabricworks.com>
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

crc32: simplify unit test code

Replace the unit test provided in crc32.c, which doesn't have a makefile
and doesn't compile with current headers, with a simpler self test
routine that also gives a measure of performance and runs at module init
time.  The self test option can be enabled through a configuration
option CONFIG_CRC32_SELFTEST.

The test stresses the pre and post loops and is thus not very realistic
since actual uses will likely have addresses and lengths that are at
least 4 byte aligned.  However, the main loop is long enough so that the
performance is dominated by that loop.

The expected values for crc32_le and crc32_be were generated with the
original version of crc32.c using CRC_BITS_LE = 8 and CRC_BITS_BE = 8.
These values were then used to check all the values of the BITS
parameters in both the original and new versions.

The performance results show some variability from run to run in spite
of attempts to both warm the cache and reduce the amount of OS noise by
limiting interrutps during the test.  To get comparable results and to
analyse options wrt performance the best time reported over a small
sample of runs has been taken.

[djwong@us.ibm.com: Minor changelog tweaks]
Signed-off-by: Bob Pearson <rpearson@systemfabricworks.com>
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

crc32: move long comment about crc32 fundamentals to Documentation/

Move a long comment from lib/crc32.c to Documentation/crc32.txt where it
will more likely get read.

Edited the resulting document to add an explanation of the slicing-by-n
algorithm.

[djwong@us.ibm.com: minor changelog tweaks]
[akpm@linux-foundation.org: fix typo, per George]
Signed-off-by: George Spelvin <linux@horizon.com>
Signed-off-by: Bob Pearson <rpearson@systemfabricworks.com>
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

crc32: remove two instances of trailing whitespaces

This patchset (re)uses Bob Pearson's crc32 slice-by-8 code to stamp out
a software crc32c implementation.  It removes the crc32c implementation
in crypto/ in favor of using the stamped-out one in lib/.  There is also
a change to Kconfig so that the kernel builder can pick an
implementation best suited for the hardware.

The motivation for this patchset is that I am working on adding full
metadata checksumming to ext4.  As far as performance impact of adding
checksumming goes, I see nearly no change with a standard mail server
ffsb simulation.  On a test that involves only file creation and
deletion and extent tree writes, I see a drop of about 50 pcercent with
the current kernel crc32c implementation; this improves to a drop of
about 20 percent with the enclosed crc32c code.

When metadata is usually a small fraction of total IO, this new
implementation doesn't help much because metadata is usually a small
fraction of total IO.  However, when we are doing IO that is almost all
metadata (such as rm -rf'ing a tree), then this patch speeds up the
operation substantially.

Incidentally, given that iscsi, sctp, and btrfs also use crc32c, this
patchset should improve their speed as well.  I have not yet quantified
that, however.  This latest submission combines Bob's patches from late
August 2011 with mine so that they can be one coherent patch set.
Please excuse my inability to combine some of the patches; I've been
advised to leave Bob's patches alone and build atop them instead.  :/

Since the last posting, I've also collected some crc32c test results on
a bunch of different x86/powerpc/sparc platforms.  The results can be
viewed here: http://goo.gl/sgt3i ; the "crc32-kern-le" and "crc32c"
columns describe the performance of the kernel's current crc32 and
crc32c software implementations.  The "crc32c-by8-le" column shows
crc32c performance with this patchset applied.  I expect crc32
performance to be roughly the same.

The two _boost columns at the right side of the spreadsheet shows how much
faster the new implementation is over the old one.  As you can see, crc32
rises substantially, and crc32c experiences a huge increase.

This patch:

- remove trailing whitespace from lib/crc32.c
- remove trailing whitespace from lib/crc32defs.h

[djwong@us.ibm.com: changelog tweaks]
Signed-off-by: Bob Pearson <rpearson@systemfabricworks.com>
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

checkpatch: check for quoted strings broken across lines

checkpatch already makes an exception to the 80-column rule for quoted
strings, and Documentation/CodingStyle recommends not splitting quoted
strings across lines, because it breaks the ability to grep for the
string.  Rather than just permitting this, actively warn about quoted
strings split across lines.

Test case:

void context(void)
{
struct { unsigned magic; const char *strdata; } foo[] = {
{ 42, "these strings"
      "do not produce warnings" },
{ 256, "though perhaps"
       "they should" },
};
pr_err("this string"
       " should produce a warning\n");
pr_err("this multi-line string\n"
       "should not produce a warning\n");
asm ("this asm\n\t"
     "should not produce a warning");
}

Results of checkpatch on that test case:

WARNING: quoted string split across lines
+        " should produce a warning\n");

total: 0 errors, 1 warnings, 15 lines checked

Signed-off-by: Josh Triplett <josh@joshtriplett.org>
Acked-by: Joe Perches <joe@perches.com>
Cc: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

checkpatch: whitespace - add/remove blank lines

Add blank lines between a few tests, remove an extraneous one.

Signed-off-by: Joe Perches <joe@perches.com>
Cc: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

checkpatch: warn on use of yield()

Using yield() is generally wrong.  Warn on its use.

Signed-off-by: Joe Perches <joe@perches.com>
Cc: Andy Whitcroft <apw@canonical.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

checkpatch: add --strict tests for braces, comments and casts

Add some more subjective --strict tests.

Add a test for block comments that start with a blank line followed only
by a line with just the comment block initiator.  Prefer a blank line
followed by /* comment...

Add a test for unnecessary spaces after a cast.

Add a test for symmetric uses of braces in if/else blocks.
If one branch needs braces, then all branches should use braces.

Signed-off-by: Joe Perches <joe@perches.com>
Cc: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

checkpatch: add [] to type extensions

Add [] to a type extensions.  Fixes false positives on:

    .attrs = (struct attribute *[]) {

Signed-off-by: Andy Whitcroft <apw@canonical.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

checkpatch: high precedence operators do not require additional parentheses in #defines

With any very high precedence operator it is not necessary to enforce
additional parentheses around simple negated expressions.  This prevents
us requesting further perentheses around the following:

    #define PMEM_IS_FREE(id, index) !(pmem[id].bitmap[index].allocated)

For now add logical and bitwise not and unary minus.

Signed-off-by: Andy Whitcroft <apw@canonical.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

checkpatch: handle string concatenation in simple #defines

Adjacent strings indicate concatentation, therefore look at identifiers
directly adjacent to literal strings as strings too.  This allows us to
better detect the form below and accept it as a simple constant:

    #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt

Signed-off-by: Andy Whitcroft <apw@canonical.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

checkpatch: allow simple character constants in #defines

Signed-off-by: Andy Whitcroft <apw@canonical.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

checkpatch: catch [ ... ] usage when not at the beginning of definition

Handle the [ A ... B ] form deeper into a definition, for example:

    static const unsigned char pci_irq_swizzle[2][PCI_MAX_DEVICES] = {
    {0, 0, 0, 0, 0, 0, 0, 27, 27, [9 ... PCI_MAX_DEVICES - 1] = 0 },
    {0, 0, 0, 0, 0, 0, 0, 29, 29, [9 ... PCI_MAX_DEVICES - 1] = 0 },
    };

Reported-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

checkpatch.pl: be silent when -q and --ignore is given

Fix checkpatch.pl when both -q and --ignore are given and prevents it from
printing a

NOTE: Ignored message types: blah

messages.

E.g., if I use -q --ignore PREFER_PACKED,PREFER_ALIGNED, i see:

NOTE: Ignored message types: PREFER_ALIGNED PREFER_PACKED

It makes no sense to print this when -q is given.

Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: Andy Whitcroft <apw@canonical.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

checkpatch: add some --strict coding style checks

Argument alignment across multiple lines should match the open
parenthesis.

Logical continuations should be at the end of the previous line, not the
start of a new line.

These are not required by CodingStyle so make the tests active only when
using --strict.

Improved by some examples from Bruce Allen.

Signed-off-by: Joe Perches <joe@perches.com>
Cc: "Bruce W. Allen" <bruce.w.allan@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

include/ and checkpatch: prefer __scanf to __attribute__((format(scanf,...)

It's equivalent to __printf, so prefer __scanf.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

prio_tree: introduce prio_set_parent()

Introduce prio_set_parent() to abstract the operation which is used to
attach the node to its parent.

Signed-off-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

prio_tree: simplify prio_tree_expand()

In current code, the deleted-node is recorded from first to last,
actually, we can directly attach these node on 'node' we will insert as
the left child, it can let the code more readable.

Signed-off-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

prio_tree: cleanup prio_tree_left()/prio_tree_right()

Introduce iter_walk_down()/iter_walk_up() to remove the common code
between prio_tree_left() and prio_tree_right().

Signed-off-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

prio_tree: remove unnecessary code in prio_tree_replace

Remove the code since 'node' has already been initialized in the begin of
the function

Signed-off-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

string: memchr_inv() speed improvements

- Generate a 64-bit pattern more efficiently

memchr_inv needs to generate a 64-bit pattern filled with a target
character.  The operation can be done by more efficient way.

- Don't call the slow check_bytes() if the memory area is 64-bit aligned

memchr_inv compares contiguous 64-bit words with the 64-bit pattern as
much as possible.  The outside of the region is checked by check_bytes()
that scans for each byte.  Unfortunately, the first 64-bit word is
unexpectedly scanned by check_bytes() even if the memory area is aligned
to a 64-bit boundary.

Both changes were originally suggested by Eric Dumazet.

Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

led-class: change back LEDS_CLASS to tristate instead of bool

After moving some core functions to led-core.c, led-class.c can be built
as module again.

Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Acked-by: Richard Purdie <richard.purdie@linuxfoundation.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/leds/leds-lm3530.c: move the code setting gen_config to one place

Improve the readability by moving the code setting gen_config to one
place.

[akpm@linux-foundation.org: fix some patch skew]
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Shreshtha Kumar Sahu <shreshthakumar.sahu@stericsson.com>
Cc: "Milo(Woogyom) Kim" <milo.kim@ti.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/leds/leds-pca9633.c: remove unused 'adapter' variable

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Peter Meerwald <p.meerwald@bct-electronic.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

leds-lm3530: replace pltfm with pdata

Use 'pdata' rather than 'pltfm' in lm3530_init_registers().

Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

leds-lm3530: remove LM3530_ALS_ZONE_REG code

LM3530_ALS_ZONE_REG is read-only register.
Writing this register is not necessary.

Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

leds-lm3530: support pwm input mode

* add 'struct lm3530_pwm_data' in the platform data
  The pwm data is the platform specific functions which generate the pwm.
  The pwm data is only valid when brightness is pwm input mode.
  Functions should be implemented by the pwm driver.
  pwm_set_intensity() : set duty of pwm.
  pwm_get_intensity() : get current the brightness.

* brightness control by pwm
  If the control mode is pwm, then brightness is changed by the duty of
  pwm=.  So pwm platform function should be called in lm3530_brightness_set().

* do not update brightness register when pwm input mode
  In pwm input mode, brightness register is not used.
  If any value is updated in this register, then the led will be off.

* when input mode is changed, set duty of pwm to 0 if unnecessary.

Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

leds-lm3530: replace i2c_client with led_classdev

To get members of lm3530_data, use 'struct led_classdev' rather than
'struct i2c_client'.

[akpm@linux-foundation.org: fix 80-column fixes more nicely]
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

leds-lm3530: set the max_brightness to 127

Only 7 bits are used for updating the brightness.  (register address :
A0h) So the max_brightness property of lm3530 should be set to 127.

On initializing registers, maximum initial brightness is limited to
'max_brightness'.

Division-by-two is removed on updating the brightness.  This arithmetic is
not necessary because the range of brightness is 0 ~ 127= .

Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/leds/leds-gpio.c: use linux/gpio.h rather than asm/gpio.h

Direct usage of the asm include has long been deprecated by the
introduction of gpiolib.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/leds: add driver for PCA9633 I2C chip

Driver for the PCA9633 I2C chip supporting four LEDs and 255 brightness
levels.

[akpm@linux-foundation.org: fix kcalloc() call]
[axel.lin@gmail.com: fix kcalloc parameters swapped]
Signed-off-by: Peter Meerwald <p.meerwald@bct-electronic.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/leds/leds-lp5523.c: constify some data

Saves ~50 bytes text and speeds things up.

Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/leds/leds-lp5521.c: ret may be uninitialized

Fix it by assigning the lp5521_read return value.

Signed-off-by: srinidhi kasagar <srinidhi.kasagar@stericsson.com>
Cc: Milo(Woogyom) Kim <milo.kim@ti.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Arun MURTHY <arun.murthy@stericsson.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/leds/leds-lp5521.c: redefinition of register bits

For better readability, values of LP5521_REG_ENABLE register were
redefined= .  Additional definitions: LP5521_ENABLE_DEFAULT and
LP5521_ENABLE_RUN_PROGRAM= .

Use definition rather than hard code value.
: 0x3F -> 'LP5521_CMD_DIRECT'

Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Arun MURTHY <arun.murthy@stericsson.com>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>