John Crispin [Mon, 5 Oct 2015 10:27:34 +0000 (10:27 +0000)]
brcm2708: switch device tree compilation to linux
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 47124
John Crispin [Mon, 5 Oct 2015 10:27:18 +0000 (10:27 +0000)]
brcm2708: fix kmod-sound-soc-bcm2708-i2s config
Right now, selecting kmod-sound-soc-bcm2708-i2s causes build errors due to
missing configs.
kmod-regmap enables I2C and SPI, causing build errors due to depending
variables not defined.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 47123
John Crispin [Mon, 5 Oct 2015 10:27:09 +0000 (10:27 +0000)]
ramips: improve systick timer
when sleep mode is disable use MIPS as clocksource and clockevent instead of systick.
because MIPS timer has higher resolution 5ns less than systick 20us and
larger counter bits 32 > 16.
clean interrupt by write compare register at isr.
fix typo cause sleep mode not enable.
Signed-off-by: Michael Lee <igvtee@gmail.com>
SVN-Revision: 47122
John Crispin [Mon, 5 Oct 2015 10:27:04 +0000 (10:27 +0000)]
ramips: fix use remove_irq to release irqaction resource
Signed-off-by: Michael Lee <igvtee@gmail.com>
SVN-Revision: 47121
John Crispin [Mon, 5 Oct 2015 10:27:00 +0000 (10:27 +0000)]
ramips: add support for 16MB VoCore
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 47120
John Crispin [Mon, 5 Oct 2015 10:26:54 +0000 (10:26 +0000)]
ramips: fix size-cells for spi nodes
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 47119
John Crispin [Mon, 5 Oct 2015 10:26:40 +0000 (10:26 +0000)]
ramips: Ralink RT3883 RGMII pinmux fix.
Due to datasheet of rt3883 SoC rgmii1 port handles pins 84-95 and rgmii2 port handles pins 72-83. When this function ports gets added to rt3883_pinmux_data there's wrong pinmux bits set (RT3883_GPIO_MODE_GE1 manages 84-95 pins and RT3883_GPIO_MODE_GE2 manages 72-83). So when enabling rgmii2 as GPIO driver confuses hardware and nothing work, neither rgmii nor gpio.
Also in '0030-pinctrl-ralink-add-pinctrl-driver.patch' typo in name of rgmii2 port.
Signed-off-by: Nick Leiten <nickleiten@gmail.com>
SVN-Revision: 47118
John Crispin [Mon, 5 Oct 2015 10:26:34 +0000 (10:26 +0000)]
ramips: Enable rx of 1536 bytes ethernet frames on MT7621
The default switch frame size (with FCS + header) is 1536 bytes. But the
GMAC only accepted frames up to 1522 bytes. Setting it to 1536 allows to
receive ethernet frames using the full of MTU 1500 + an extra VLAN header +
VLAN header added by the switch.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 47117
John Crispin [Mon, 5 Oct 2015 10:26:28 +0000 (10:26 +0000)]
ramips: Fix too small rx buffer
The driver assumes that the maximum received buffer for non-jumbo frames is
1536 bytes. But the allocation of the rx fragment doesn't reflect that. It
currently allocates fragments which will only be large enough to be used as
rx buffer with the size of 1534 bytes. This is problematic because the GMAC
will now try to write to 2 bytes which don't belong to its receive buffer
when a large enough ethernet frame is received.
This may already be a problem on existing chips but will at least become a
problem when the 1536 byte rx modus is enabled on MT7621a. It is required
on this SoC to receive ethernet frames which use their full 1500 bytes MTU
and a VLAN header next to the switch VLAN tag.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 47116
John Crispin [Mon, 5 Oct 2015 10:26:21 +0000 (10:26 +0000)]
ramips: Fix setting of rx buffer length
The length of the DMA rx buffer was always set to 0 because the function
for extracting the length was used to calculate the value for setting it.
Instead the macro has to be split in a get and set function similar to the
TX_DMA_(GET_|)PLEN(0|1) macro.
No problem was noticed on MT7621a before this was changed and thus maybe it
was hidden by different problem which is not yet fixed.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 47115
John Crispin [Mon, 5 Oct 2015 10:26:09 +0000 (10:26 +0000)]
ramips: Allow to receive vlan over untag ports on MT7530
The MT7530 switch driver with enable_vlan set will automatically set all
ports to the user port mode. The hardware will remove the incoming vlan tag
on these ports and use it for its internal vlan. This is usually not wanted
and makes it impossible to communicate via vlan over the switch in both
directions.
It is possible to configure a switch port to "transparent mode" when this
port is only used as untag in the switch VLANs. This will disable the VLAN
untagging of packets when they were received on this port. The tagging on
"tag" ports based on the vlan id is still working.
The transparent port mode cannot be used when a port is both used in a VLAN
as "tag" and in another one as "untag" port.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 47114
John Crispin [Mon, 5 Oct 2015 10:26:02 +0000 (10:26 +0000)]
ramips: Add build files for HiWiFi HC5x61 models
HiWiFi HC5661/5761/5861 models are manufactured by http://www.hiwifi.com <http://www.hiwifi.com/>. These models have similar hardware specs(MT7620A + 128M DDR2 + 16M flash). This patch adds support for them.
The original author is Justin Liu (rssnsj@gmail.com). I ported the patch to trunk and submitted it here with his approval.
v3 fix
1: Spaces -> Tabs
2: Removed some packages
Signed-off-by: Xiaoning Kang <kangxn@163.com>
SVN-Revision: 47113
John Crispin [Mon, 5 Oct 2015 10:25:53 +0000 (10:25 +0000)]
ramips: Add DTS files for HiWiFi HC5x61 models
HiWiFi HC5661/5761/5861 models are manufactured by http://www.hiwifi.com. These models have similar hardware specs(MT7620A + 128M DDR2 + 16M flash). This patch adds support for them.
The original author is Justin Liu (rssnsj@gmail.com). I ported the patch to trunk and submitted it here with his approval.
v3 fix
1: Merged most stuff into dtsi file
2: Remove unnecessary empty lines.
Signed-off-by: Xiaoning Kang <kangxn@163.com>
SVN-Revision: 47112
John Crispin [Mon, 5 Oct 2015 10:25:47 +0000 (10:25 +0000)]
ramips: Add base-files for HiWiFi HC5x61 models
HiWiFi HC5661/5761/5861 models are manufactured by http://www.hiwifi.com. These models have similar hardware specs(MT7620A + 128M DDR2 + 16M flash). This patch adds support for them.
The original author is Justin Liu (rssnsj@gmail.com). I ported the patch to trunk and submitted it here with his approval.
v3 fix
1: Fixed model order
2: Remove manufacturer name from model name
3: Use a hacky but prettier way to get mac address.
Signed-off-by: Xiaoning Kang <kangxn@163.com>
SVN-Revision: 47111
John Crispin [Mon, 5 Oct 2015 10:25:40 +0000 (10:25 +0000)]
ar71xx: Correct WeIO board name
Trivial parch to correct WeIO board name in the system.
Signed-off-by: Drasko DRASKOVIC <drasko.draskovic@gmail.com>
SVN-Revision: 47110
John Crispin [Mon, 5 Oct 2015 10:25:28 +0000 (10:25 +0000)]
target/mpc85xx: check if 'generic' subtarget for image file cuImage.tl-wdr4900-v1
Only add 'cuImage.tl-wdr4900-v1' to KERNEL_IMAGES if
the selected subtarget is 'generic'.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
SVN-Revision: 47109
Jo-Philipp Wich [Mon, 5 Oct 2015 09:10:17 +0000 (09:10 +0000)]
iwinfo: nl80211: add support for reading TX power from netlink
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47108
Rafał Miłecki [Mon, 5 Oct 2015 08:54:26 +0000 (08:54 +0000)]
ar71xx: rename firmware for Chinese version of TL-WR941ND v6
It seems there are two *different* versions on TL-WR941ND v6: Chinese
and European one. Currently supported by OpenWrt is Chinese one. Rename
firmware to make it clear.
For details see:
http://wiki.openwrt.org/toh/tp-link/tl-wr941nd
https://forum.openwrt.org/viewtopic.php?id=59295
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 47107
Matteo Croce [Sun, 4 Oct 2015 22:10:18 +0000 (22:10 +0000)]
lantiq: fix gcc 5 build
SVN-Revision: 47106
Matteo Croce [Sun, 4 Oct 2015 22:03:04 +0000 (22:03 +0000)]
lantiq: fix binutils 2.15.1 build
SVN-Revision: 47105
Hauke Mehrtens [Sun, 4 Oct 2015 11:34:39 +0000 (11:34 +0000)]
kernel: update 4.1 to 4.1.10
Fixes a regression on spi flash devices (upstream commit
1583eaece6fa).
Changelogs:
* https://www.kernel.org/pub/linux/kernel/v4.x/ChangeLog-4.1.7
* https://www.kernel.org/pub/linux/kernel/v4.x/ChangeLog-4.1.8
* https://www.kernel.org/pub/linux/kernel/v4.x/ChangeLog-4.1.9
* https://www.kernel.org/pub/linux/kernel/v4.x/ChangeLog-4.1.10
096-ipv4-off-by-one-in-continuation-handling-in-proc-net.patch was applied
upstream and dropped.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
[update from 4.1.9 to 4.1.10]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47104
Jo-Philipp Wich [Sat, 3 Oct 2015 09:49:24 +0000 (09:49 +0000)]
toplevel.mk: drop LD_LIBRARY_PATH overrides
Overriding LD_LIBRARY_PATH for host utilities frequently leads to problems
with host executables loading shared libraries from the staging_dir, leading
to crashes due to incompatible ABIs.
Since most host utilties either embed a proper rpath or are reworked to link
statically we do not need the workaround anymore.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47103
Felix Fietkau [Fri, 2 Oct 2015 16:24:15 +0000 (16:24 +0000)]
libnl: Install include files into libnl3
Install header files into same location as pkgconfig/libnl-3.0.pc says:
Cflags: -I${includedir}/libnl3
Signed-off-by: Bruno Randolf <br1@einfach.org>
SVN-Revision: 47102
Steven Barth [Fri, 2 Oct 2015 08:24:35 +0000 (08:24 +0000)]
iproute2: adapt coexistence layer to new unified path
Signed-off-by: Steven Barth <steven@midlink.org>
SVN-Revision: 47081
Steven Barth [Fri, 2 Oct 2015 08:24:32 +0000 (08:24 +0000)]
base-files: sanitize and unify $PATH
Previously init and hotplug paths were different from console.
Signed-off-by: Steven Barth <steven@midlink.org>
SVN-Revision: 47080
Rafał Miłecki [Fri, 2 Oct 2015 06:03:13 +0000 (06:03 +0000)]
procd: make nand_do_platform_check check image only
Recently all targets have been updated to call nand_do_upgrade directly.
It's not needed anymore to leave a magic /tmp/sysupgrade-nand-path mark
during image check.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 47079
Felix Fietkau [Thu, 1 Oct 2015 19:50:06 +0000 (19:50 +0000)]
musl: re-enable des crypto support, fixes pppd MPPE issues
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47078
Felix Fietkau [Thu, 1 Oct 2015 19:50:01 +0000 (19:50 +0000)]
toolchain/uClibc: add support of uClibc-ng
uClibc-ng is a spin-off of original uClibc, see http://www.uclibc-ng.org/
We try to regularly add changes from uClibc to uClibc-ng.
We even sent patches and bug reports to the uClibc mailing list.
The config file is compatible between uClibc-ng 1.0 and uClibc git master.
This might change in the future.
Our main goal is to provide regularly a stable and tested release
to make embedded system developers happy.
The main advantage of uClibc-ng over olde good uClibc is regular releases
so there's no need to keep tons of patches on top of years old
0.9.33.2
Build-tested for
[1] ARM: Sunxi generic
[2] MIPS: Netgear WNDR3600/3700/3800
Run-tested for [yet out of the tree] Synopsys Designware ARC AXS101.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Waldemar Brodkorb <wbx@uclibc-ng.org>
Cc: Mathieu Olivari <mathieu@codeaurora.org>
Cc: Felix Fietkau <nbd@openwrt.org>
Cc: John Crispin <blogic@openwrt.org>
SVN-Revision: 47077
John Crispin [Thu, 1 Oct 2015 19:12:14 +0000 (19:12 +0000)]
ralink: add irq to mt7628 gpio node
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 47076
John Crispin [Thu, 1 Oct 2015 18:44:26 +0000 (18:44 +0000)]
rpcd: update to latest git HEAD
Provides ubus calls for sysupgrade and password changing.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 47075
John Crispin [Thu, 1 Oct 2015 18:13:47 +0000 (18:13 +0000)]
ralink: the mmc driver can now handle CD lines that are active low
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 47074
John Crispin [Thu, 1 Oct 2015 15:35:44 +0000 (15:35 +0000)]
ralink: speed selection was broken in spi-mt7621
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 47073
Jo-Philipp Wich [Tue, 29 Sep 2015 11:37:27 +0000 (11:37 +0000)]
quilt: add further relocatability fixes
Prevent quilt's build system from generating useless compat wrappers and
hardcoded absolute utility paths to binaries in staging_dir/host/.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47070
Jo-Philipp Wich [Tue, 29 Sep 2015 11:37:10 +0000 (11:37 +0000)]
prereq-build: test availability of Perl Thread::Queue module
This is needed for building automake.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47069
Felix Fietkau [Mon, 28 Sep 2015 12:22:35 +0000 (12:22 +0000)]
uml: backport another upstream patch to fix compile errors
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47067
Felix Fietkau [Mon, 28 Sep 2015 09:40:39 +0000 (09:40 +0000)]
base-files: add a dependency on fstools
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47066
Rafał Miłecki [Mon, 28 Sep 2015 09:09:00 +0000 (09:09 +0000)]
hostapd: check for banned client on association event
When using FullMAC drivers (e.g. brcmfmac) we don't get mgmt frames so
check for banned client in probe request handler won't ever be used.
Since cfg80211 provides us info about STA associating let's put a check
there.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 47064
Felix Fietkau [Sun, 27 Sep 2015 22:39:53 +0000 (22:39 +0000)]
mt76: update to the latest version, fixes some aggregation issues
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47063
Felix Fietkau [Sun, 27 Sep 2015 17:29:48 +0000 (17:29 +0000)]
uml: fix build with gcc 5
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47062
Felix Fietkau [Sun, 27 Sep 2015 17:29:38 +0000 (17:29 +0000)]
uml: update to linux 4.1
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47061
Rafał Miłecki [Sun, 27 Sep 2015 10:25:27 +0000 (10:25 +0000)]
mac80211: backport patch setting TX power in interface info
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 47059
Rafał Miłecki [Sun, 27 Sep 2015 06:53:12 +0000 (06:53 +0000)]
brcm47xx: describe 300-fork_cacheflush.patch & 310-no_highpage.patch
These were initially commited in r9285.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 47058
Rafał Miłecki [Sun, 27 Sep 2015 06:24:33 +0000 (06:24 +0000)]
brcm47xx: describe 160-kmap_coherent.patch
It was initially commited in r6642.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 47057
Rafał Miłecki [Sun, 27 Sep 2015 06:05:53 +0000 (06:05 +0000)]
brcm47xx: describe 610-pci_ide_fix.patch
It was initially commited in r20924.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 47056
Felix Fietkau [Sat, 26 Sep 2015 23:27:23 +0000 (23:27 +0000)]
igmpproxy: fix spurious restarts on interface events, pass used netdevs to procd instead
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47055
Felix Fietkau [Sat, 26 Sep 2015 23:18:40 +0000 (23:18 +0000)]
netifd: update to the latest version, fixes spurious client isolation in unbridged AP configurations (#20574)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47053
Rafał Miłecki [Sat, 26 Sep 2015 22:57:33 +0000 (22:57 +0000)]
bcm53xx: add early support for Linksys EA6300 V1
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 47052
Felix Fietkau [Sat, 26 Sep 2015 21:10:48 +0000 (21:10 +0000)]
bison: replace the yacc script with one that does not hardcode the path (fixes #20605)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47050
Felix Fietkau [Sat, 26 Sep 2015 21:10:37 +0000 (21:10 +0000)]
tools/patch: enable parallel build
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47049
Jo-Philipp Wich [Fri, 25 Sep 2015 08:41:12 +0000 (08:41 +0000)]
firewall: allow DHCPv6 traffic to/from fc00::/6 instead of fe80::/10
There is no RFC requirement that DHCPv6 servers must reply with a link local
address and some ISP servers in the wild appear to using addresses in the ULA
range to send DHCPv6 offers.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47048
Rafał Miłecki [Fri, 25 Sep 2015 04:22:13 +0000 (04:22 +0000)]
kernel: crypto: fix ubsec_ssb.c compilation with 4.0+
SSB_DEVTABLE_END was removed in 4.0 by upstream commit
673e2baaa6d9
("treewide: Remove unnecessary SSB_DEVTABLE_END macro").
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 47047
Felix Fietkau [Thu, 24 Sep 2015 16:07:10 +0000 (16:07 +0000)]
kernel: backport some SPI layer improvements from 4.1 to 3.18, significantly improves flash speed on ramips
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47045
Felix Fietkau [Thu, 24 Sep 2015 15:39:45 +0000 (15:39 +0000)]
mt76: update to the latest version, adds performance improvements
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47043
Felix Fietkau [Thu, 24 Sep 2015 15:02:15 +0000 (15:02 +0000)]
ath9k: fix handling of tx headroom for padding (fixes #20556)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47042
Felix Fietkau [Thu, 24 Sep 2015 15:02:07 +0000 (15:02 +0000)]
mac80211: fix a few issues with fast-xmit support
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47041
Rafał Miłecki [Thu, 24 Sep 2015 11:19:12 +0000 (11:19 +0000)]
kernel: remove old "rootfs" splitter
A year ago I made this old splitter obsolete (see r42828), it's time to
completely remove it now. For all this time we got these warnings:
"Dedicated partitioner didn't create "rootfs_data" partition, please fill a bug report!"
and
"Support for built-in "rootfs_data" splitter will be removed, please use CONFIG_MTD_SPLIT_SQUASHFS_ROOT"
but I'm not aware of any bug reports related to that.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 47040
Rafał Miłecki [Thu, 24 Sep 2015 09:18:59 +0000 (09:18 +0000)]
oxnas: add platform_pre_upgrade for sysupgrade
We're in process of cleaning nand_do_platform_check. Currently it leaves
a special mark in /tmp/sysupgrade-nand-path triggering some diffent code
path in nand_upgrade_stage1. This can be a bit confusing.
The plan is to have the check function only check the image and nothing
else. Then platform code (platform_pre_upgrade) should trigger NAND
specific upgrade path. This is what this patch implements.
This follows all other targets making it finally possible to change
nand_do_platform_check.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 47039
Rafał Miłecki [Thu, 24 Sep 2015 09:18:47 +0000 (09:18 +0000)]
oxnas: drop some unused sysupgrade code
First of all platform_do_upgrade_phase2 doesn't seem to be defined
anywhere. Other than that platform_do_upgrade is not likely to be ever
called. There is a call to nand_do_platform_check which triggers
nand_upgrade_stage1 call with "exit 0" in it.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 47038
Felix Fietkau [Thu, 24 Sep 2015 09:08:52 +0000 (09:08 +0000)]
libnl: split libnl into smaller libraries
Some modules may require only libnl-genl, some
libnl-route and fewer would require libnl-nf.
This patch splits the entire libnl package into smaller
more granular libs that can be installed individually as required.
Also added libnl*.so symlinks for convenience.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
SVN-Revision: 47037
Felix Fietkau [Thu, 24 Sep 2015 09:08:47 +0000 (09:08 +0000)]
ar71xx: Add WeIO Board Support
Add support for WeIO board (http://we-io.net).
This board is based on Carambola2 board form 8Devices.
Signed-off-by: Drasko DRASKOVIC <drasko.draskovic@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org> [some cleanups]
SVN-Revision: 47036
Felix Fietkau [Thu, 24 Sep 2015 08:41:15 +0000 (08:41 +0000)]
kernel: add missing CAN related config symbol
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47035
Felix Fietkau [Thu, 24 Sep 2015 08:37:50 +0000 (08:37 +0000)]
ar71xx: fix bogus hardcoded kernel image size for Seama images (fixes #20585)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47034
Felix Fietkau [Thu, 24 Sep 2015 08:37:40 +0000 (08:37 +0000)]
dropbear: add respawn param in case dropbear crashes
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
SVN-Revision: 47033
Felix Fietkau [Thu, 24 Sep 2015 08:37:35 +0000 (08:37 +0000)]
imx6: disable ext2/ext3 filesystem support (ext4 is enough)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47032
Felix Fietkau [Thu, 24 Sep 2015 08:37:30 +0000 (08:37 +0000)]
uml: disable ext2/ext3 filesystem support (ext4 is enough)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47031
Felix Fietkau [Thu, 24 Sep 2015 08:37:23 +0000 (08:37 +0000)]
arm64: disable ext2/ext3 filesystem support (ext4 is enough)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47030
Jo-Philipp Wich [Wed, 23 Sep 2015 18:40:42 +0000 (18:40 +0000)]
mxs: fixup permissions of image generation scripts
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47029
Felix Fietkau [Tue, 22 Sep 2015 11:28:28 +0000 (11:28 +0000)]
kernel: add a patch to fix crashes on pppoe disconnect/reconnect
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47026
Felix Fietkau [Tue, 22 Sep 2015 09:06:00 +0000 (09:06 +0000)]
px5g-standalone: use /dev/urandom instead of havege (fixes #20216)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47025
Felix Fietkau [Tue, 22 Sep 2015 08:30:15 +0000 (08:30 +0000)]
gcc: fix accidentally dropped chunk of the musl gcc 5.2.0 powerpc patch (fixes #20501)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47024
Felix Fietkau [Tue, 22 Sep 2015 08:30:05 +0000 (08:30 +0000)]
gcc: use qstrip template to fix syntax highlighting
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47023
Steven Barth [Mon, 21 Sep 2015 21:15:41 +0000 (21:15 +0000)]
package: Remove dependencies to kmod-ipv6
Since r46834, IPv6 support is builtin if selected. Therefor, dependencies
on kmod-ipv6 can no longer be fulfilled, since it is not a module anymore.
Signed-off-by: Arjen de Korte <arjen+openwrt@de-korte.org>
SVN-Revision: 47022
Zoltan Herpai [Mon, 21 Sep 2015 21:10:43 +0000 (21:10 +0000)]
mxs: re-work SD card image generation
- Duckbill uses a different partitioning approach than standard
FSL and Olimex
- use new sdimage to integrate U-Boot into the SD card images
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
SVN-Revision: 47021
Zoltan Herpai [Mon, 21 Sep 2015 21:08:08 +0000 (21:08 +0000)]
tools: add sdimage for mxs
This tool is used for SD card generation on Freescale i.MX23/i.MX28
platforms. These CPU's ROM need a tiny header of front of a boot stream.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
SVN-Revision: 47020
Zoltan Herpai [Mon, 21 Sep 2015 21:05:16 +0000 (21:05 +0000)]
mxs: adopt SD card generation to fixed U-Boot path
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
SVN-Revision: 47019
Zoltan Herpai [Mon, 21 Sep 2015 21:04:24 +0000 (21:04 +0000)]
packages: uboot-mxs: bless UBOOT_IMAGE with a meaning
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
SVN-Revision: 47018
Zoltan Herpai [Mon, 21 Sep 2015 21:03:37 +0000 (21:03 +0000)]
packages: uboot-mxs: do no modify the U-Boot image, copy as-is
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
SVN-Revision: 47017
Felix Fietkau [Mon, 21 Sep 2015 17:41:07 +0000 (17:41 +0000)]
base-files: fix ramoverlay function with kernels 3.18+
Even though there are not many users left within the OpenWrt tree it seems
this function broke during the kernel 3.18 transition.
Fix it by providing a workdir as required by overlayfs.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
SVN-Revision: 47015
Felix Fietkau [Mon, 21 Sep 2015 17:40:59 +0000 (17:40 +0000)]
uqmi: Add qmi.sh executable bit and fix option dhcp
Using protocol qmi does not work since qmi.sh is not executable.
Setting option dhcp explicitely to 0 actually enables it.
This patch fixes both problems.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 47014
Felix Fietkau [Mon, 21 Sep 2015 17:40:52 +0000 (17:40 +0000)]
omap: add Kernel 4.1
tested on Beagleboard C4
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 47013
Felix Fietkau [Mon, 21 Sep 2015 17:40:44 +0000 (17:40 +0000)]
musl: fix build on sh3
musl fails to build when compiled with gcc on sh3 (GCC target/#67260).
Work it around.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
SVN-Revision: 47012
Felix Fietkau [Mon, 21 Sep 2015 17:18:52 +0000 (17:18 +0000)]
tools/mtd-utils: fix PKG_MIRROR_MD5SUM
The checksum doesn't match the file on mirror2.openwrt.org.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 47010
Felix Fietkau [Mon, 21 Sep 2015 17:18:43 +0000 (17:18 +0000)]
ath10k: remove API v2 firmware, it is no longer needed
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47009
Zoltan Herpai [Fri, 18 Sep 2015 19:29:23 +0000 (19:29 +0000)]
packages: uboot-mxs: place binaries in the designated path
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
SVN-Revision: 47008
Zoltan Herpai [Fri, 18 Sep 2015 19:24:38 +0000 (19:24 +0000)]
packages: uboot-mxs: fix I2SE Duckbill variant
The current patch to add Duckbill support is wrong and does not
even compile. So replace this patch with a working one.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
SVN-Revision: 47007
Felix Fietkau [Fri, 18 Sep 2015 13:40:03 +0000 (13:40 +0000)]
iw: restore limited event monitor functionality (#20546)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47006
Felix Fietkau [Fri, 18 Sep 2015 13:39:55 +0000 (13:39 +0000)]
arm64: switch to Kernel 4.1
- fix Kernel dts subdir location
- enable virtio networking
we are using -M virt which supports virtio devices
changes in symbols due to make kernel_oldconfig:
- CONFIG_ARCH_BINFMT_ELF_RANDOMIZE_PIE=y : removed
fix security: upstream id:
d1fd836dcf00d2028c700c7e44d2c23404062c90
- CONFIG_ARM64_CPU_SUSPEND: removed
commit id:
af3cfdbf56b91785650f54e7c9a899d814b4b9fb
- CONFIG_ARM64_PGTABLE_LEVELS=3 : renamed PGTABLE_LEVELS
commit id:
9f25e6ad58e1fb3b4d441e4c55635c4598a6fa94
- CONFIG_GENERIC_CLOCKEVENTS_BUILD=y : removed upstream
commit id:
9f083b74df3a7eaa100b456f2dc195512daf728e
-# CONFIG_PREEMPT_RCU: unnecessary
unknown remove reasons:
-CONFIG_GENERIC_IOMAP=y
-# CONFIG_POWER_RESET_GPIO is not set
-# CONFIG_POWER_RESET_GPIO_RESTART is not set
-# CONFIG_POWER_RESET_LTC2952 is not set
-# CONFIG_POWER_RESET_SYSCON is not set
-# CONFIG_XEN is not set
tested and boot, networking work with qemu
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 47005
Felix Fietkau [Fri, 18 Sep 2015 09:05:11 +0000 (09:05 +0000)]
mac80211: add missing dependency for the hermes driver (#20543)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46998
Felix Fietkau [Fri, 18 Sep 2015 09:05:01 +0000 (09:05 +0000)]
kernel: fix dependencies of the sock_diag debloat patch (#20544)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46997
Felix Fietkau [Thu, 17 Sep 2015 15:38:58 +0000 (15:38 +0000)]
kernel: solos-pci: Increase headroom on received packets
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46993
Felix Fietkau [Thu, 17 Sep 2015 15:38:46 +0000 (15:38 +0000)]
kernel: ipv6: ip6_fragment: fix headroom tests and skb leak
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46992
Jo-Philipp Wich [Thu, 17 Sep 2015 15:31:45 +0000 (15:31 +0000)]
firewall: depend on kmod-ipt-conntrack (#20542)
Our ruleset requires kernel support for conntrack state matching, therfore
depend on the require kmod. Fixes #20542.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 46990
Jo-Philipp Wich [Thu, 17 Sep 2015 13:07:48 +0000 (13:07 +0000)]
tools/mtd-utils: avoid linking libm statically
Rework static linker flags to not link libm statically, this should fix the
build on CentOS where libm.a is not provided by the libc devel package.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 46989
Felix Fietkau [Thu, 17 Sep 2015 10:15:52 +0000 (10:15 +0000)]
x86/geode: enable DMI and Geos support (fixes #20512)
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
SVN-Revision: 46986
Felix Fietkau [Thu, 17 Sep 2015 10:15:45 +0000 (10:15 +0000)]
x86: fix Geode LX timekeeping (#20531)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46985
Felix Fietkau [Thu, 17 Sep 2015 09:45:34 +0000 (09:45 +0000)]
kernel: remove lantiq specific ATM API hacks and their kernel space users (fixes #20523)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46984
John Crispin [Wed, 16 Sep 2015 12:40:40 +0000 (12:40 +0000)]
kernel: unbreak atm ABI for 4.0 and 4.1
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 46983
Felix Fietkau [Wed, 16 Sep 2015 12:38:16 +0000 (12:38 +0000)]
build: do not overwrite already existing host commands
This prevents a later prereq check from overwriting the installed tar
binary.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46982
John Crispin [Wed, 16 Sep 2015 12:08:05 +0000 (12:08 +0000)]
kernel: properly guard the lantiq atm abi hack with an ifdef
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 46981
John Crispin [Wed, 16 Sep 2015 09:37:39 +0000 (09:37 +0000)]
opkg: Extend 'opkg list' command to optionally display package size
'opkg list' command only displays the available packages' name, version and
description. It would be useful to also see the approximate size of the
available package.
This patch extends "opkg list" command with "--size" to optionally show also
the *.ipk size.
* Default behaviour is to list the available packages as earlier:
"name - version - description"
* with "--size" the output of is "name - version - size - description".
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
SVN-Revision: 46980
projects / openwrt / staging / hauke.git / log